diff options
Diffstat (limited to 'Documentation')
8 files changed, 194 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt new file mode 100644 index 000000000000..c93d88fdd858 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt @@ -0,0 +1,39 @@ +Microchip PIC32 Clock Controller Binding +---------------------------------------- +Microchip clock controller is consists of few oscillators, PLL, multiplexer +and few divider modules. + +This binding uses common clock bindings. +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "microchip,pic32mzda-clk". +- reg: shall contain base address and length of clock registers. +- #clock-cells: shall be 1. + +Optional properties: +- microchip,pic32mzda-sosc: shall be added only if platform has + secondary oscillator connected. + +Example: + rootclk: clock-controller@1f801200 { + compatible = "microchip,pic32mzda-clk"; + reg = <0x1f801200 0x200>; + #clock-cells = <1>; + /* optional */ + microchip,pic32mzda-sosc; + }; + + +The clock consumer shall specify the desired clock-output of the clock +controller (as defined in [2]) by specifying output-id in its "clock" +phandle cell. +[2] include/dt-bindings/clock/microchip,pic32-clock.h + +For example for UART2: +uart2: serial@2 { + compatible = "microchip,pic32mzda-uart"; + reg = <>; + interrupts = <>; + clocks = <&rootclk PB2CLK>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt new file mode 100644 index 000000000000..4040905388d9 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt @@ -0,0 +1,57 @@ +Broadcom BCM6345-style Level 1 interrupt controller + +This block is a first level interrupt controller that is typically connected +directly to one of the HW INT lines on each CPU. + +Key elements of the hardware design include: + +- 32, 64 or 128 incoming level IRQ lines + +- Most onchip peripherals are wired directly to an L1 input + +- A separate instance of the register set for each CPU, allowing individual + peripheral IRQs to be routed to any CPU + +- Contains one or more enable/status word pairs per CPU + +- No atomic set/clear operations + +- No polarity/level/edge settings + +- No FIFO or priority encoder logic; software is expected to read all + 2-4 status words to determine which IRQs are pending + +Required properties: + +- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc" +- reg: specifies the base physical address and size of the registers; + the number of supported IRQs is inferred from the size argument +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller(s) + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node; valid values depend on the type of parent interrupt controller + +If multiple reg ranges and interrupt-parent entries are present on an SMP +system, the driver will allow IRQ SMP affinity to be set up through the +/proc/irq/ interface. In the simplest possible configuration, only one +reg range and one interrupt-parent is needed. + +The driver operates in native CPU endian by default, there is no support for +specifying an alternative endianness. + +Example: + +periph_intc: interrupt-controller@10000000 { + compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc"; + reg = <0x10000020 0x20>, + <0x10000040 0x20>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>, <3>; +}; diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt index 7bab90cc4a7b..4a7e030e4f9b 100644 --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -4,7 +4,8 @@ Required properties: - compatible: "brcm,bcm3384", "brcm,bcm33843" "brcm,bcm3384-viper", "brcm,bcm33843-viper" - "brcm,bcm6328", "brcm,bcm6368", + "brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6368", + "brcm,bcm63168", "brcm,bcm63268", "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu3.txt b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt new file mode 100644 index 000000000000..616862ad2b71 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit v3 + +Properties: +- compatible: "cavium,octeon-7890-ciu3" + + Compatibility with 78XX and 73XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is source number. + The second cell indicates the triggering semantics, and may have a + value of either 4 for level semantics, or 1 for edge semantics. + +Example: + interrupt-controller@1010000000000 { + compatible = "cavium,octeon-7890-ciu3"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Source number (20 significant bits) + * 2) Trigger type: (4 == level, 1 == edge) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10100 0x00000000 0x0 0xb0000000>; + }; diff --git a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt new file mode 100644 index 000000000000..65b38bf60ae0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt @@ -0,0 +1,29 @@ +* Microchip Universal Asynchronous Receiver Transmitter (UART) + +Required properties: +- compatible: Should be "microchip,pic32mzda-uart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the UART peripheral. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +Optional properties: +- cts-gpios: CTS pin for UART + +Example: + uart1: serial@1f822000 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822000 0x50>; + interrupts = <112 IRQ_TYPE_LEVEL_HIGH>, + <113 IRQ_TYPE_LEVEL_HIGH>, + <114 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&PBCLK2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 + &pinctrl_uart1_cts + &pinctrl_uart1_rts>; + cts-gpios = <&gpio1 15 0>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 021bbe7866e0..316412dc7913 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -72,6 +72,8 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +dptechnics DPTechnics +dragino Dragino Technology Co., Limited ea Embedded Artists AB ebv EBV Elektronik edt Emerging Display Technologies @@ -176,6 +178,7 @@ nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. olimex OLIMEX Ltd. +onion Onion Corporation onnn ON Semiconductor Corp. opencores OpenCores.org option Option NV diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt new file mode 100644 index 000000000000..852f694f3177 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt @@ -0,0 +1,19 @@ +* Microchip PIC32 Deadman Timer + +The deadman timer is used to reset the processor in the event of a software +malfunction. It is a free-running instruction fetch timer, which is clocked +whenever an instruction fetch occurs until a count match occurs. + +Required properties: +- compatible: must be "microchip,pic32mzda-dmt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of parent clock (should be &PBCLK7). + +Example: + + watchdog@1f800a00 { + compatible = "microchip,pic32mzda-dmt"; + reg = <0x1f800a00 0x80>; + clocks = <&PBCLK7>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt new file mode 100644 index 000000000000..d1401030e75c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt @@ -0,0 +1,18 @@ +* Microchip PIC32 Watchdog Timer + +When enabled, the watchdog peripheral can be used to reset the device if the +WDT is not cleared periodically in software. + +Required properties: +- compatible: must be "microchip,pic32mzda-wdt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of source clk. should be <&LPRC> clk. + +Example: + + watchdog@1f800800 { + compatible = "microchip,pic32mzda-wdt"; + reg = <0x1f800800 0x200>; + clocks = <&LPRC>; + }; |