diff options
Diffstat (limited to 'Documentation')
26 files changed, 202 insertions, 76 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm index 5cedf72df358..f7be0e88b139 100644 --- a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm +++ b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm @@ -19,6 +19,25 @@ Description: Set to 0 to pad all frames. Set greater than tx_max to disable all padding. +What: /sys/class/net/<iface>/cdc_ncm/ndp_to_end +Date: Dec 2015 +KernelVersion: 4.5 +Contact: Bjørn Mork <bjorn@mork.no> +Description: + Boolean attribute showing the status of the "NDP to + end" quirk. Defaults to 'N', except for devices + already known to need it enabled. + + The "NDP to end" quirk makes the driver place the NDP + (the packet index table) after the payload. The NCM + specification does not mandate this, but some devices + are known to be more restrictive. Write 'Y' to this + attribute for temporary testing of a suspect device + failing to work with the default driver settings. + + A device entry should be added to the driver if this + quirk is found to be required. + What: /sys/class/net/<iface>/cdc_ncm/rx_max Date: May 2014 KernelVersion: 3.16 diff --git a/Documentation/ABI/testing/sysfs-class-net-mesh b/Documentation/ABI/testing/sysfs-class-net-mesh index c46406296631..c2b956d44a95 100644 --- a/Documentation/ABI/testing/sysfs-class-net-mesh +++ b/Documentation/ABI/testing/sysfs-class-net-mesh @@ -8,7 +8,7 @@ Description: What: /sys/class/net/<mesh_iface>/mesh/<vlan_subdir>/ap_isolation Date: May 2011 -Contact: Antonio Quartulli <antonio@meshcoding.com> +Contact: Antonio Quartulli <a@unstable.cc> Description: Indicates whether the data traffic going from a wireless client to another wireless client will be @@ -70,7 +70,7 @@ Description: What: /sys/class/net/<mesh_iface>/mesh/isolation_mark Date: Nov 2013 -Contact: Antonio Quartulli <antonio@meshcoding.com> +Contact: Antonio Quartulli <a@unstable.cc> Description: Defines the isolation mark (and its bitmask) which is used to classify clients as "isolated" by the diff --git a/Documentation/ABI/testing/sysfs-class-net-qmi b/Documentation/ABI/testing/sysfs-class-net-qmi new file mode 100644 index 000000000000..fa5a00bb1143 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-net-qmi @@ -0,0 +1,23 @@ +What: /sys/class/net/<iface>/qmi/raw_ip +Date: Dec 2015 +KernelVersion: 4.4 +Contact: Bjørn Mork <bjorn@mork.no> +Description: + Boolean. Default: 'N' + + Set this to 'Y' to change the network device link + framing from '802.3' to 'raw-ip'. + + The netdev will change to reflect the link framing + mode. The netdev is an ordinary ethernet device in + '802.3' mode, and the driver expects to exchange + frames with an ethernet header over the USB link. The + netdev is a headerless p-t-p device in 'raw-ip' mode, + and the driver expects to echange IPv4 or IPv6 packets + without any L2 header over the USB link. + + Userspace is in full control of firmware configuration + through the delegation of the QMI protocol. Userspace + is responsible for coordination of driver and firmware + link framing mode, changing this setting to 'Y' if the + firmware is configured for 'raw-ip' mode. diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 31d1d658827f..c0d8788e75d3 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -587,7 +587,7 @@ used to control it: modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type> preaction=<preaction type> preop=<preop type> start_now=x - nowayout=x ifnum_to_use=n + nowayout=x ifnum_to_use=n panic_wdt_timeout=<t> ifnum_to_use specifies which interface the watchdog timer should use. The default is -1, which means to pick the first one registered. @@ -597,7 +597,9 @@ is the amount of seconds before the reset that the pre-timeout panic will occur (if pretimeout is zero, then pretimeout will not be enabled). Note that the pretimeout is the time before the final timeout. So if the timeout is 50 seconds and the pretimeout is 10 seconds, then the pretimeout -will occur in 40 second (10 seconds before the timeout). +will occur in 40 second (10 seconds before the timeout). The panic_wdt_timeout +is the value of timeout which is set on kernel panic, in order to let actions +such as kdump to occur during panic. The action may be "reset", "power_cycle", or "power_off", and specifies what to do when the timer times out, and defaults to @@ -634,6 +636,7 @@ for configuring the watchdog: ipmi_watchdog.preop=<preop type> ipmi_watchdog.start_now=x ipmi_watchdog.nowayout=x + ipmi_watchdog.panic_wdt_timeout=<t> The options are the same as the module parameter options. diff --git a/Documentation/arm/keystone/Overview.txt b/Documentation/arm/keystone/Overview.txt index f17bc4c9dff9..400c0c270d2e 100644 --- a/Documentation/arm/keystone/Overview.txt +++ b/Documentation/arm/keystone/Overview.txt @@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:- The device tree documentation for the keystone machines are located at Documentation/devicetree/bindings/arm/keystone/keystone.txt -Known issues & workaround -------------------------- - -Some of the device drivers used on keystone are re-used from that from -DaVinci and other TI SoCs. These device drivers may use clock APIs directly. -Some of the keystone specific drivers such as netcp uses run time power -management API instead to enable clock. As this API has limitations on -keystone, following workaround is needed to boot Linux. - - Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise - clock frameworks will try to disable clocks that are unused and disable - the hardware. This is because netcp related power domain and clock - domains are enabled in u-boot as run time power management API currently - doesn't enable clocks for netcp due to a limitation. This workaround is - expected to be removed in the future when proper API support becomes - available. Until then, this work around is needed. - - Document Author --------------- Murali Karicheri <m-karicheri2@ti.com> diff --git a/Documentation/block/null_blk.txt b/Documentation/block/null_blk.txt index 2f6c6ff7161d..d8880ca30af4 100644 --- a/Documentation/block/null_blk.txt +++ b/Documentation/block/null_blk.txt @@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0 parameter. 1: The multi-queue block layer is instantiated with a hardware dispatch queue for each CPU node in the system. + +use_lightnvm=[0/1]: Default: 0 + Register device with LightNVM. Requires blk-mq to be used. diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index d3d0a4fb1c73..079b42a81d7c 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -22,8 +22,7 @@ Required properties: Optional properties: - ti,hwmods: Name of the hwmods associated to the eDMA CC - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow - these channels will be SW triggered channels. The list must - contain 16 bits numbers, see example. + these channels will be SW triggered channels. See example. - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by the driver, they are allocated to be used by for example the DSP. See example. @@ -56,10 +55,9 @@ edma: edma@49000000 { ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>; /* Channel 20 and 21 is allocated for memcpy */ - ti,edma-memcpy-channels = /bits/ 16 <20 21>; - /* The following PaRAM slots are reserved: 35-45 and 100-110 */ - ti,edma-reserved-slot-ranges = /bits/ 16 <35 10>, - /bits/ 16 <100 10>; + ti,edma-memcpy-channels = <20 21>; + /* The following PaRAM slots are reserved: 35-44 and 100-109 */ + ti,edma-reserved-slot-ranges = <35 10>, <100 10>; }; edma_tptc0: tptc@49800000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index f2455c50533d..120bc4971cf3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -11,6 +11,10 @@ Required properties: 0 = active high 1 = active low +Optional properties: +- little-endian : GPIO registers are used as little endian. If not + present registers are used as big endian by default. + Example: gpio0: gpio@1100 { diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt index b9c32f6fd687..4357e498ef04 100644 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -12,7 +12,7 @@ Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": Required subnode-properties: - label: Descriptive name of the key. - linux,code: Keycode to emit. - - channel: Channel this key is attached to, mut be 0 or 1. + - channel: Channel this key is attached to, must be 0 or 1. - voltage: Voltage in µV at lradc input when this key is pressed. Example: diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index f1e2a02381a4..1c63e40659fc 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -6,7 +6,9 @@ used for what purposes, but which don't use an on-flash partition table such as RedBoot. The partition table should be a subnode of the mtd node and should be named -'partitions'. Partitions are defined in subnodes of the partitions node. +'partitions'. This node should have the following property: +- compatible : (required) must be "fixed-partitions" +Partitions are then defined in subnodes of the partitions node. For backwards compatibility partitions as direct subnodes of the mtd device are supported. This use is discouraged. @@ -36,6 +38,7 @@ Examples: flash@0 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; @@ -53,6 +56,7 @@ flash@0 { flash@1 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <2>; @@ -66,6 +70,7 @@ flash@1 { flash@2 { partitions { + compatible = "fixed-partitions"; #address-cells = <2>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 9853f8e70966..28a4781ab6d7 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -40,18 +40,18 @@ Optional properties: Slave Properties: Required properties: -- phy_id : Specifies slave phy id - phy-mode : See ethernet.txt file in the same directory Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy_id : Specifies slave phy id - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the properties phy_id and phy-mode, - or the sub-node fixed-link can be specified + Either the property phy_id, or the sub-node + fixed-link can be specified Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 04e6bef3ac3f..5fdbbcdf8c4b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -31,6 +31,8 @@ A switch child node has the following optional property: switch. Must be set if the switch can not detect the presence and/or size of a connected EEPROM, otherwise optional. +- reset-gpios : phandle and specifier to a gpio line connected to + reset pin of the switch chip. A switch may have multiple "port" children nodes @@ -114,6 +116,7 @@ Example: #size-cells = <0>; reg = <17 1>; /* MDIO address 17, switch 1 in tree */ mii-bus = <&mii_bus1>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; switch1port0: port@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt index 9c23fdf25018..4a7ede9657b0 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt @@ -1,7 +1,12 @@ Hisilicon MDIO bus controller Properties: -- compatible: "hisilicon,mdio","hisilicon,hns-mdio". +- compatible: can be one of: + "hisilicon,hns-mdio" + "hisilicon,mdio" + "hisilicon,hns-mdio" is recommended to be used for hip05 and later SOCs, + while "hisilicon,mdio" is optional for backwards compatibility only on + hip04 Soc. - reg: The base address of the MDIO bus controller register bank. - #address-cells: Must be <1>. - #size-cells: Must be <0>. MDIO addresses have no size component. diff --git a/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt new file mode 100644 index 000000000000..dea5124cdc52 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt @@ -0,0 +1,18 @@ +* ADF7242 IEEE 802.15.4 * + +Required properties: + - compatible: should be "adi,adf7242" + - spi-max-frequency: maximal bus speed (12.5 MHz) + - reg: the chipselect index + - interrupts: the interrupt generated by the device via pin IRQ1. + IRQ_TYPE_LEVEL_HIGH (4) or IRQ_TYPE_EDGE_FALLING (1) + +Example: + + adf7242@0 { + compatible = "adi,adf7242"; + spi-max-frequency = <10000000>; + reg = <0>; + interrupts = <98 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index b5d79761ac97..38c8e845ac5d 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -19,6 +19,9 @@ Required properties: Optional elements: 'tx_clk' - clocks: Phandles to input clocks. +Optional properties for PHY child node: +- reset-gpios : Should specify the gpio for phy reset + Examples: macb0: ethernet@fffc4000 { @@ -29,4 +32,8 @@ Examples: local-mac-address = [3a 0e 03 04 05 06]; clock-names = "pclk", "hclk", "tx_clk"; clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; + ethernet-phy@1 { + reg = <0x1>; + reset-gpios = <&pioE 6 1>; + }; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index f5a8ca29aff0..aeea50c84e92 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -8,6 +8,11 @@ Required properties: - phy-mode: See ethernet.txt file in the same directory - clocks: a pointer to the reference clock for this device. +Optional properties: +- tx-csum-limit: maximum mtu supported by port that allow TX checksum. + Value is presented in bytes. If not used, by default 1600B is set for + "marvell,armada-370-neta" and 9800B for others. + Example: ethernet@d0070000 { @@ -15,6 +20,7 @@ ethernet@d0070000 { reg = <0xd0070000 0x2500>; interrupts = <8>; clocks = <&gate_clk 4>; + tx-csum-limit = <9800> status = "okay"; phy = <&phy0>; phy-mode = "rgmii-id"; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 692076fda0e5..f9c32adab5c6 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,8 +1,9 @@ Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY -Some boards require special tuning values, particularly when it comes to -clock delays. You can specify clock delay values by adding -micrel-specific properties to an Ethernet OF device node. +Some boards require special tuning values, particularly when it comes +to clock delays. You can specify clock delay values in the PHY OF +device node. Deprecated, but still supported, these properties can +also be added to an Ethernet OF device node. Note that these settings are applied after any phy-specific fixup from phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), @@ -57,16 +58,6 @@ KSZ9031: Examples: - /* Attach to an Ethernet device with autodetected PHY */ - &enet { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - status = "okay"; - }; - - /* Attach to an explicitly-specified PHY */ mdio { phy0: ethernet-phy@0 { rxc-skew-ps = <3000>; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index b486f3f5f6a3..81a9f9e6b45f 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -5,8 +5,18 @@ interface contains. Required properties: - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC. + "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC. "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC. "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC. + "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface. + "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of (1) the register block and (2) the stream buffer. - interrupts: A list of interrupt-specifiers, one for each entry in interrupt-names. @@ -37,7 +47,7 @@ Optional properties: Example: ethernet@e6800000 { - compatible = "renesas,etheravb-r8a7795"; + compatible = "renesas,etheravb-r8a7795", "renesas,etheravb-rcar-gen3"; reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 3a9d67951606..72d82d684342 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -11,6 +11,8 @@ Required properties: designware version numbers documented in stmmac.txt - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. + - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock + for ptp ref clk. This affects all emacs as the clock is common. Optional properties: altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index f34fc3c81a75..e862a922bd3f 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -35,18 +35,18 @@ Optional properties: - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given - max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock and - the second clock should be peripheral's register interface clock. Further - clocks may be specified in derived bindings. -- clock-names: One name for each entry in the clocks property, the - first one should be "stmmaceth" and the second one should be "pclk". -- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is - available this clock is used for programming the Timestamp Addend Register. - If not passed then the system clock will be used and this is fine on some - platforms. +- clocks: If present, the first clock should be the GMAC main clock + The optional second clock should be peripheral's register interface clock. + The third optional clock should be the ptp reference clock. + Further clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property. + The first one should be "stmmaceth". + The optional second one should be "pclk". + The optional third one should be "clk_ptp_ref". - snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory +- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: @@ -65,4 +65,11 @@ Examples: tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: ethernet-phy@0 { + }; + }; }; diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index b38200d2583a..0dfa60d88dd3 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -1,7 +1,9 @@ * Temperature Sensor ADC (TSADC) on rockchip SoCs Required properties: -- compatible : "rockchip,rk3288-tsadc" +- compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3368-tsadc": found on RK3368 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/fault-injection/notifier-error-inject.txt b/Documentation/fault-injection/notifier-error-inject.txt index 09adabef513f..83d3f4e43e91 100644 --- a/Documentation/fault-injection/notifier-error-inject.txt +++ b/Documentation/fault-injection/notifier-error-inject.txt @@ -10,6 +10,7 @@ modules that can be used to test the following notifiers. * PM notifier * Memory hotplug notifier * powerpc pSeries reconfig notifier + * Netdevice notifier CPU notifier error injection module ----------------------------------- @@ -87,6 +88,30 @@ Possible pSeries reconfig notifier events to be failed are: * PSERIES_DRCONF_MEM_ADD * PSERIES_DRCONF_MEM_REMOVE +Netdevice notifier error injection module +---------------------------------------------- +This feature is controlled through debugfs interface +/sys/kernel/debug/notifier-error-inject/netdev/actions/<notifier event>/error + +Netdevice notifier events which can be failed are: + + * NETDEV_REGISTER + * NETDEV_CHANGEMTU + * NETDEV_CHANGENAME + * NETDEV_PRE_UP + * NETDEV_PRE_TYPE_CHANGE + * NETDEV_POST_INIT + * NETDEV_PRECHANGEMTU + * NETDEV_PRECHANGEUPPER + * NETDEV_CHANGEUPPER + +Example: Inject netdevice mtu change error (-22 == -EINVAL) + + # cd /sys/kernel/debug/notifier-error-inject/netdev + # echo -22 > actions/NETDEV_CHANGEMTU/error + # ip link set eth0 mtu 1024 + RTNETLINK answers: Invalid argument + For more usage examples ----------------------- There are tools/testing/selftests using the notifier error injection features diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 6a4b1af724f8..1bba38dd2637 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -32,6 +32,7 @@ Supported adapters: * Intel Sunrise Point-LP (PCH) * Intel DNV (SOC) * Intel Broxton (SOC) + * Intel Lewisburg (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index f8aae632f02f..742f69d18fc8 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1583,9 +1583,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. hwp_only Only load intel_pstate on systems which support hardware P state control (HWP) if available. - no_acpi - Don't use ACPI processor performance control objects - _PSS and _PPC specified limits. intremap= [X86-64, Intel-IOMMU] on enable Interrupt Remapping (default) diff --git a/Documentation/networking/e100.txt b/Documentation/networking/e100.txt index f862cf3aff34..42ddbd4b52a9 100644 --- a/Documentation/networking/e100.txt +++ b/Documentation/networking/e100.txt @@ -181,17 +181,3 @@ For general information, go to the Intel support website at: If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to e1000-devel@lists.sourceforge.net. - - -License -======= - -This software program is released under the terms of a license agreement -between you ('Licensee') and Intel. Do not use or load this software or any -associated materials (collectively, the 'Software') until you have carefully -read the full terms and conditions of the file COPYING located in this software -package. By loading or using the Software, you agree to the terms of this -Agreement. If you do not agree with the terms of this Agreement, do not install -or use the Software. - -* Other names and brands may be claimed as the property of others. diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 2ea4c45cf1c8..ceb44a095a27 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -335,6 +335,14 @@ tcp_keepalive_intvl - INTEGER after probes started. Default value: 75sec i.e. connection will be aborted after ~11 minutes of retries. +tcp_l3mdev_accept - BOOLEAN + Enables child sockets to inherit the L3 master device index. + Enabling this option allows a "global" listen socket to work + across L3 master domains (e.g., VRFs) with connected sockets + derived from the listen socket to be bound to the L3 domain in + which the packets originated. Only valid when the kernel was + compiled with CONFIG_NET_L3_MASTER_DEV. + tcp_low_latency - BOOLEAN If set, the TCP stack makes decisions that prefer lower latency as opposed to higher throughput. By default, this @@ -1723,6 +1731,25 @@ addip_enable - BOOLEAN Default: 0 +pf_enable - INTEGER + Enable or disable pf (pf is short for potentially failed) state. A value + of pf_retrans > path_max_retrans also disables pf state. That is, one of + both pf_enable and pf_retrans > path_max_retrans can disable pf state. + Since pf_retrans and path_max_retrans can be changed by userspace + application, sometimes user expects to disable pf state by the value of + pf_retrans > path_max_retrans, but occasionally the value of pf_retrans + or path_max_retrans is changed by the user application, this pf state is + enabled. As such, it is necessary to add this to dynamically enable + and disable pf state. See: + https://datatracker.ietf.org/doc/draft-ietf-tsvwg-sctp-failover for + details. + + 1: Enable pf. + + 0: Disable pf. + + Default: 1 + addip_noauth_enable - BOOLEAN Dynamic Address Reconfiguration (ADD-IP) requires the use of authentication to protect the operations of adding or removing new @@ -1799,7 +1826,9 @@ pf_retrans - INTEGER having to reduce path_max_retrans to a very low value. See: http://www.ietf.org/id/draft-nishida-tsvwg-sctp-failover-05.txt for details. Note also that a value of pf_retrans > path_max_retrans - disables this feature + disables this feature. Since both pf_retrans and path_max_retrans can + be changed by userspace application, a variable pf_enable is used to + disable pf state. Default: 0 |