diff options
Diffstat (limited to 'Documentation/sound/oss/CMI8330')
| -rw-r--r-- | Documentation/sound/oss/CMI8330 | 152 |
1 files changed, 0 insertions, 152 deletions
diff --git a/Documentation/sound/oss/CMI8330 b/Documentation/sound/oss/CMI8330 deleted file mode 100644 index 8a5fd1611c6f..000000000000 --- a/Documentation/sound/oss/CMI8330 +++ /dev/null @@ -1,152 +0,0 @@ -Documentation for CMI 8330 (SoundPRO) -------------------------------------- -Alessandro Zummo <azummo@ita.flashnet.it> - -( Be sure to read Documentation/sound/oss/SoundPro too ) - - -This adapter is now directly supported by the sb driver. - - The only thing you have to do is to compile the kernel sound -support as a module and to enable kernel ISAPnP support, -as shown below. - - -CONFIG_SOUND=m -CONFIG_SOUND_SB=m - -CONFIG_PNP=y -CONFIG_ISAPNP=y - - -and optionally: - - -CONFIG_SOUND_MPU401=m - - for MPU401 support. - - -(I suggest you to use "make menuconfig" or "make xconfig" - for a more comfortable configuration editing) - - - -Then you can do - - modprobe sb - -and everything will be (hopefully) configured. - -You should get something similar in syslog: - -sb: CMI8330 detected. -sb: CMI8330 sb base located at 0x220 -sb: CMI8330 mpu base located at 0x330 -sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it> -sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5 - - - - -The old documentation file follows for reference -purposes. - - -How to enable CMI 8330 (SOUNDPRO) soundchip on Linux ------------------------------------------- -Stefan Laudat <Stefan.Laudat@asit.ro> - -[Note: The CMI 8338 is unrelated and is supported by cmpci.o] - - - In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but -you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/. - - Of course you will have to compile kernel sound support as module, as shown below: - -CONFIG_SOUND=m -CONFIG_SOUND_OSS=m -CONFIG_SOUND_SB=m -CONFIG_SOUND_ADLIB=m -CONFIG_SOUND_MPU401=m -# Mikro$chaft sound system (kinda useful here ;)) -CONFIG_SOUND_MSS=m - - The /etc/isapnp.conf file will be: - -<snip below> - - -(READPORT 0x0203) -(ISOLATE PRESERVE) -(IDENTIFY *) -(VERBOSITY 2) -(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING -(VERIFYLD N) - - -# WSS - -(CONFIGURE CMI0001/16777472 (LD 0 -(IO 0 (SIZE 8) (BASE 0x0530)) -(IO 1 (SIZE 8) (BASE 0x0388)) -(INT 0 (IRQ 7 (MODE +E))) -(DMA 0 (CHANNEL 0)) -(NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# MPU - -(CONFIGURE CMI0001/16777472 (LD 1 -(IO 0 (SIZE 2) (BASE 0x0330)) -(INT 0 (IRQ 11 (MODE +E))) -(NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# Joystick - -(CONFIGURE CMI0001/16777472 (LD 2 -(IO 0 (SIZE 8) (BASE 0x0200)) -(NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# SoundBlaster - -(CONFIGURE CMI0001/16777472 (LD 3 -(IO 0 (SIZE 16) (BASE 0x0220)) -(INT 0 (IRQ 5 (MODE +E))) -(DMA 0 (CHANNEL 1)) -(DMA 1 (CHANNEL 5)) -(NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - - -(WAITFORKEY) - -<end of snip> - - The module sequence is trivial: - -/sbin/insmod soundcore -/sbin/insmod sound -/sbin/insmod uart401 -# insert this first -/sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1 -# The sb module is an alternative to the ad1848 (Microsoft Sound System) -# Anyhow, this is full duplex and has MIDI -/sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330 - - - -Alma Chao <elysian@ethereal.torsion.org> suggests the following in -a /etc/modprobe.d/*conf file: - -alias sound ad1848 -alias synth0 opl3 -options ad1848 io=0x530 irq=7 dma=0 soundpro=1 -options opl3 io=0x388 |