diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/README.ipw2200 | 2 | ||||
| -rw-r--r-- | Documentation/networking/bonding.txt | 84 | ||||
| -rw-r--r-- | Documentation/networking/caif/spi_porting.txt | 208 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/packet_mmap.txt | 26 | ||||
| -rw-r--r-- | Documentation/networking/pktgen.txt | 5 |
6 files changed, 323 insertions, 4 deletions
diff --git a/Documentation/networking/README.ipw2200 b/Documentation/networking/README.ipw2200 index c276490165e7..616a8e540b0b 100644 --- a/Documentation/networking/README.ipw2200 +++ b/Documentation/networking/README.ipw2200 @@ -171,7 +171,7 @@ Where the supported parameter are: led Can be used to turn on experimental LED code. - 0 = Off, 1 = On. Default is 0. + 0 = Off, 1 = On. Default is 1. mode Can be used to set the default mode of the adapter. diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index e0ec7cb3f672..d2b62b71b617 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,6 +49,7 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs +3.5 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -1318,8 +1319,87 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves - -4. Querying Bonding Configuration +3.5 Overriding Configuration for Special Cases +---------------------------------------------- +When using the bonding driver, the physical port which transmits a frame is +typically selected by the bonding driver, and is not relevant to the user or +system administrator. The output port is simply selected using the policies of +the selected bonding mode. On occasion however, it is helpful to direct certain +classes of traffic to certain physical interfaces on output to implement +slightly more complex policies. For example, to reach a web server over a +bonded interface in which eth0 connects to a private network, while eth1 +connects via a public network, it may be desirous to bias the bond to send said +traffic over eth0 first, using eth1 only as a fall back, while all other traffic +can safely be sent over either interface. Such configurations may be achieved +using the traffic control utilities inherent in linux. + +By default the bonding driver is multiqueue aware and 16 queues are created +when the driver initializes (see Documentation/networking/multiqueue.txt +for details). If more or less queues are desired the module parameter +tx_queues can be used to change this value. There is no sysfs parameter +available as the allocation is done at module init time. + +The output of the file /proc/net/bonding/bondX has changed so the output Queue +ID is now printed for each slave: + +Bonding Mode: fault-tolerance (active-backup) +Primary Slave: None +Currently Active Slave: eth0 +MII Status: up +MII Polling Interval (ms): 0 +Up Delay (ms): 0 +Down Delay (ms): 0 + +Slave Interface: eth0 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cb +Slave queue ID: 0 + +Slave Interface: eth1 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cc +Slave queue ID: 2 + +The queue_id for a slave can be set using the command: + +# echo "eth1:2" > /sys/class/net/bond0/bonding/queue_id + +Any interface that needs a queue_id set should set it with multiple calls +like the one above until proper priorities are set for all interfaces. On +distributions that allow configuration via initscripts, multiple 'queue_id' +arguments can be added to BONDING_OPTS to set all needed slave queues. + +These queue id's can be used in conjunction with the tc utility to configure +a multiqueue qdisc and filters to bias certain traffic to transmit on certain +slave devices. For instance, say we wanted, in the above configuration to +force all traffic bound to 192.168.1.100 to use eth1 in the bond as its output +device. The following commands would accomplish this: + +# tc qdisc add dev bond0 handle 1 root multiq + +# tc filter add dev bond0 protocol ip parent 1: prio 1 u32 match ip dst \ + 192.168.1.100 action skbedit queue_mapping 2 + +These commands tell the kernel to attach a multiqueue queue discipline to the +bond0 interface and filter traffic enqueued to it, such that packets with a dst +ip of 192.168.1.100 have their output queue mapping value overwritten to 2. +This value is then passed into the driver, causing the normal output path +selection policy to be overridden, selecting instead qid 2, which maps to eth1. + +Note that qid values begin at 1. Qid 0 is reserved to initiate to the driver +that normal output policy selection should take place. One benefit to simply +leaving the qid for a slave to 0 is the multiqueue awareness in the bonding +driver that is now present. This awareness allows tc filters to be placed on +slave devices as well as bond devices and the bonding driver will simply act as +a pass-through for selecting output queues on the slave device rather than +output port selection. + +This feature first appeared in bonding driver version 3.7.0 and support for +output slave selection was limited to round-robin and active-backup modes. + +4 Querying Bonding Configuration ================================= 4.1 Bonding Configuration diff --git a/Documentation/networking/caif/spi_porting.txt b/Documentation/networking/caif/spi_porting.txt new file mode 100644 index 000000000000..61d7c9247453 --- /dev/null +++ b/Documentation/networking/caif/spi_porting.txt @@ -0,0 +1,208 @@ +- CAIF SPI porting - + +- CAIF SPI basics: + +Running CAIF over SPI needs some extra setup, owing to the nature of SPI. +Two extra GPIOs have been added in order to negotiate the transfers + between the master and the slave. The minimum requirement for running +CAIF over SPI is a SPI slave chip and two GPIOs (more details below). +Please note that running as a slave implies that you need to keep up +with the master clock. An overrun or underrun event is fatal. + +- CAIF SPI framework: + +To make porting as easy as possible, the CAIF SPI has been divided in +two parts. The first part (called the interface part) deals with all +generic functionality such as length framing, SPI frame negotiation +and SPI frame delivery and transmission. The other part is the CAIF +SPI slave device part, which is the module that you have to write if +you want to run SPI CAIF on a new hardware. This part takes care of +the physical hardware, both with regard to SPI and to GPIOs. + +- Implementing a CAIF SPI device: + + - Functionality provided by the CAIF SPI slave device: + + In order to implement a SPI device you will, as a minimum, + need to implement the following + functions: + + int (*init_xfer) (struct cfspi_xfer * xfer, struct cfspi_dev *dev): + + This function is called by the CAIF SPI interface to give + you a chance to set up your hardware to be ready to receive + a stream of data from the master. The xfer structure contains + both physical and logical adresses, as well as the total length + of the transfer in both directions.The dev parameter can be used + to map to different CAIF SPI slave devices. + + void (*sig_xfer) (bool xfer, struct cfspi_dev *dev): + + This function is called by the CAIF SPI interface when the output + (SPI_INT) GPIO needs to change state. The boolean value of the xfer + variable indicates whether the GPIO should be asserted (HIGH) or + deasserted (LOW). The dev parameter can be used to map to different CAIF + SPI slave devices. + + - Functionality provided by the CAIF SPI interface: + + void (*ss_cb) (bool assert, struct cfspi_ifc *ifc); + + This function is called by the CAIF SPI slave device in order to + signal a change of state of the input GPIO (SS) to the interface. + Only active edges are mandatory to be reported. + This function can be called from IRQ context (recommended in order + not to introduce latency). The ifc parameter should be the pointer + returned from the platform probe function in the SPI device structure. + + void (*xfer_done_cb) (struct cfspi_ifc *ifc); + + This function is called by the CAIF SPI slave device in order to + report that a transfer is completed. This function should only be + called once both the transmission and the reception are completed. + This function can be called from IRQ context (recommended in order + not to introduce latency). The ifc parameter should be the pointer + returned from the platform probe function in the SPI device structure. + + - Connecting the bits and pieces: + + - Filling in the SPI slave device structure: + + Connect the necessary callback functions. + Indicate clock speed (used to calculate toggle delays). + Chose a suitable name (helps debugging if you use several CAIF + SPI slave devices). + Assign your private data (can be used to map to your structure). + + - Filling in the SPI slave platform device structure: + Add name of driver to connect to ("cfspi_sspi"). + Assign the SPI slave device structure as platform data. + +- Padding: + +In order to optimize throughput, a number of SPI padding options are provided. +Padding can be enabled independently for uplink and downlink transfers. +Padding can be enabled for the head, the tail and for the total frame size. +The padding needs to be correctly configured on both sides of the link. +The padding can be changed via module parameters in cfspi_sspi.c or via +the sysfs directory of the cfspi_sspi driver (before device registration). + +- CAIF SPI device template: + +/* + * Copyright (C) ST-Ericsson AB 2010 + * Author: Daniel Martensson / Daniel.Martensson@stericsson.com + * License terms: GNU General Public License (GPL), version 2. + * + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <linux/wait.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <net/caif/caif_spi.h> + +MODULE_LICENSE("GPL"); + +struct sspi_struct { + struct cfspi_dev sdev; + struct cfspi_xfer *xfer; +}; + +static struct sspi_struct slave; +static struct platform_device slave_device; + +static irqreturn_t sspi_irq(int irq, void *arg) +{ + /* You only need to trigger on an edge to the active state of the + * SS signal. Once a edge is detected, the ss_cb() function should be + * called with the parameter assert set to true. It is OK + * (and even advised) to call the ss_cb() function in IRQ context in + * order not to add any delay. */ + + return IRQ_HANDLED; +} + +static void sspi_complete(void *context) +{ + /* Normally the DMA or the SPI framework will call you back + * in something similar to this. The only thing you need to + * do is to call the xfer_done_cb() function, providing the pointer + * to the CAIF SPI interface. It is OK to call this function + * from IRQ context. */ +} + +static int sspi_init_xfer(struct cfspi_xfer *xfer, struct cfspi_dev *dev) +{ + /* Store transfer info. For a normal implementation you should + * set up your DMA here and make sure that you are ready to + * receive the data from the master SPI. */ + + struct sspi_struct *sspi = (struct sspi_struct *)dev->priv; + + sspi->xfer = xfer; + + return 0; +} + +void sspi_sig_xfer(bool xfer, struct cfspi_dev *dev) +{ + /* If xfer is true then you should assert the SPI_INT to indicate to + * the master that you are ready to recieve the data from the master + * SPI. If xfer is false then you should de-assert SPI_INT to indicate + * that the transfer is done. + */ + + struct sspi_struct *sspi = (struct sspi_struct *)dev->priv; +} + +static void sspi_release(struct device *dev) +{ + /* + * Here you should release your SPI device resources. + */ +} + +static int __init sspi_init(void) +{ + /* Here you should initialize your SPI device by providing the + * necessary functions, clock speed, name and private data. Once + * done, you can register your device with the + * platform_device_register() function. This function will return + * with the CAIF SPI interface initialized. This is probably also + * the place where you should set up your GPIOs, interrupts and SPI + * resources. */ + + int res = 0; + + /* Initialize slave device. */ + slave.sdev.init_xfer = sspi_init_xfer; + slave.sdev.sig_xfer = sspi_sig_xfer; + slave.sdev.clk_mhz = 13; + slave.sdev.priv = &slave; + slave.sdev.name = "spi_sspi"; + slave_device.dev.release = sspi_release; + + /* Initialize platform device. */ + slave_device.name = "cfspi_sspi"; + slave_device.dev.platform_data = &slave.sdev; + + /* Register platform device. */ + res = platform_device_register(&slave_device); + if (res) { + printk(KERN_WARNING "sspi_init: failed to register dev.\n"); + return -ENODEV; + } + + return res; +} + +static void __exit sspi_exit(void) +{ + platform_device_del(&slave_device); +} + +module_init(sspi_init); +module_exit(sspi_exit); diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index d0536b5a4e01..f350c69b2bb4 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -903,7 +903,7 @@ arp_ignore - INTEGER arp_notify - BOOLEAN Define mode for notification of address and device changes. 0 - (default): do nothing - 1 - Generate gratuitous arp replies when device is brought up + 1 - Generate gratuitous arp requests when device is brought up or hardware address changes. arp_accept - BOOLEAN diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt index 2a72262fbadf..073894d1c093 100644 --- a/Documentation/networking/packet_mmap.txt +++ b/Documentation/networking/packet_mmap.txt @@ -493,6 +493,32 @@ The user can also use poll() to check if a buffer is available: pfd.events = POLLOUT; retval = poll(&pfd, 1, timeout); +------------------------------------------------------------------------------- ++ PACKET_TIMESTAMP +------------------------------------------------------------------------------- + +The PACKET_TIMESTAMP setting determines the source of the timestamp in +the packet meta information. If your NIC is capable of timestamping +packets in hardware, you can request those hardware timestamps to used. +Note: you may need to enable the generation of hardware timestamps with +SIOCSHWTSTAMP. + +PACKET_TIMESTAMP accepts the same integer bit field as +SO_TIMESTAMPING. However, only the SOF_TIMESTAMPING_SYS_HARDWARE +and SOF_TIMESTAMPING_RAW_HARDWARE values are recognized by +PACKET_TIMESTAMP. SOF_TIMESTAMPING_SYS_HARDWARE takes precedence over +SOF_TIMESTAMPING_RAW_HARDWARE if both bits are set. + + int req = 0; + req |= SOF_TIMESTAMPING_SYS_HARDWARE; + setsockopt(fd, SOL_PACKET, PACKET_TIMESTAMP, (void *) &req, sizeof(req)) + +If PACKET_TIMESTAMP is not set, a software timestamp generated inside +the networking stack is used (the behavior before this setting was added). + +See include/linux/net_tstamp.h and Documentation/networking/timestamping +for more information on hardware timestamps. + -------------------------------------------------------------------------------- + THANKS -------------------------------------------------------------------------------- diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt index 61bb645d50e0..75e4fd708ccb 100644 --- a/Documentation/networking/pktgen.txt +++ b/Documentation/networking/pktgen.txt @@ -151,6 +151,8 @@ Examples: pgset stop aborts injection. Also, ^C aborts generator. + pgset "rate 300M" set rate to 300 Mb/s + pgset "ratep 1000000" set rate to 1Mpps Example scripts =============== @@ -241,6 +243,9 @@ src6 flows flowlen +rate +ratep + References: ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/ ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/ |