diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 64 |
1 files changed, 47 insertions, 17 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index e87bdbfbcc75..7bcdebffdab3 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -56,7 +56,6 @@ parameter is applicable: ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. - KMEMTRACE kmemtrace is enabled. LIBATA Libata driver is enabled LP Printer support is enabled. LOOP Loopback device support is enabled. @@ -329,11 +328,6 @@ and is between 256 and 4096 characters. It is defined in the file flushed before they will be reused, which is a lot of faster - amd_iommu_size= [HW,X86-64] - Define the size of the aperture for the AMD IOMMU - driver. Possible values are: - '32M', '64M' (default), '128M', '256M', '512M', '1G' - amijoy.map= [HW,JOY] Amiga joystick support Map of devices attached to JOY0DAT and JOY1DAT Format: <a>,<b> @@ -646,6 +640,13 @@ and is between 256 and 4096 characters. It is defined in the file DMA-API debugging code disables itself because the architectural default is too low. + dma_debug_driver=<driver_name> + With this option the DMA-API debugging driver + filter feature can be enabled at boot time. Just + pass the driver to filter for as the parameter. + The filter can be disabled or changed to another + driver later using sysfs. + dscc4.setup= [NET] dtc3181e= [HW,SCSI] @@ -752,12 +753,25 @@ and is between 256 and 4096 characters. It is defined in the file ia64_pal_cache_flush instead of SAL_CACHE_FLUSH. ftrace=[tracer] - [ftrace] will set and start the specified tracer + [FTRACE] will set and start the specified tracer as early as possible in order to facilitate early boot debugging. ftrace_dump_on_oops - [ftrace] will dump the trace buffers on oops. + [FTRACE] will dump the trace buffers on oops. + + ftrace_filter=[function-list] + [FTRACE] Limit the functions traced by the function + tracer at boot up. function-list is a comma separated + list of functions. This list can be changed at run + time by the set_ftrace_filter file in the debugfs + tracing directory. + + ftrace_notrace=[function-list] + [FTRACE] Do not trace the functions specified in + function-list. This list can be changed at run time + by the set_ftrace_notrace file in the debugfs + tracing directory. gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad @@ -914,6 +928,12 @@ and is between 256 and 4096 characters. It is defined in the file Formt: { "sha1" | "md5" } default: "sha1" + ima_tcb [IMA] + Load a policy which meets the needs of the Trusted + Computing Base. This means IMA will measure all + programs exec'd, files mmap'd for exec, and all files + opened for read by uid=0. + in2000= [HW,SCSI] See header of drivers/scsi/in2000.c. @@ -1054,15 +1074,6 @@ and is between 256 and 4096 characters. It is defined in the file use the HighMem zone if it exists, and the Normal zone if it does not. - kmemtrace.enable= [KNL,KMEMTRACE] Format: { yes | no } - Controls whether kmemtrace is enabled - at boot-time. - - kmemtrace.subbufs=n [KNL,KMEMTRACE] Overrides the number of - subbufs kmemtrace's relay channel has. Set this - higher than default (KMEMTRACE_N_SUBBUFS in code) if - you experience buffer overruns. - kgdboc= [HW] kgdb over consoles. Requires a tty driver that supports console polling. (only serial suported for now) @@ -1072,6 +1083,10 @@ and is between 256 and 4096 characters. It is defined in the file Configure the RouterBoard 532 series on-chip Ethernet adapter MAC address. + kmemleak= [KNL] Boot-time kmemleak enable/disable + Valid arguments: on, off + Default: on + kstack=N [X86] Print N words from the kernel stack in oops dumps. @@ -1535,6 +1550,10 @@ and is between 256 and 4096 characters. It is defined in the file register save and restore. The kernel will only save legacy floating-point registers on task switch. + noxsave [BUGS=X86] Disables x86 extended register state save + and restore using xsave. The kernel will fallback to + enabling legacy floating-point and sse state. + nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or wfi(ARM) instruction doesn't work correctly and not to use it. This is also useful when using JTAG debugger. @@ -1571,6 +1590,9 @@ and is between 256 and 4096 characters. It is defined in the file noinitrd [RAM] Tells the kernel not to load any configured initial RAM disk. + nointremap [X86-64, Intel-IOMMU] Do not enable interrupt + remapping. + nointroute [IA-64] nojitter [IA64] Disables jitter checking for ITC timers. @@ -1656,6 +1678,14 @@ and is between 256 and 4096 characters. It is defined in the file oprofile.timer= [HW] Use timer interrupt instead of performance counters + oprofile.cpu_type= Force an oprofile cpu type + This might be useful if you have an older oprofile + userland or if you want common events. + Format: { archperfmon } + archperfmon: [X86] Force use of architectural + perfmon on Intel CPUs instead of the + CPU specific event set. + osst= [HW,SCSI] SCSI Tape Driver Format: <buffer_size>,<write_threshold> See also Documentation/scsi/st.txt. |