diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 44 |
1 files changed, 28 insertions, 16 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 54f21a5c262b..be3bde51b564 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -44,6 +44,7 @@ parameter is applicable: FB The frame buffer device is enabled. HW Appropriate hardware is enabled. IA-64 IA-64 architecture is enabled. + IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. ISAPNP ISA PnP code is enabled. @@ -492,10 +493,12 @@ and is between 256 and 4096 characters. It is defined in the file Default: 64 hpet= [X86-32,HPET] option to control HPET usage - Format: { enable (default) | disable | force } + Format: { enable (default) | disable | force | + verbose } disable: disable HPET and use PIT instead force: allow force enabled of undocumented chips (ICH4, VIA, nVidia) + verbose: show contents of HPET registers during setup com20020= [HW,NET] ARCnet - COM20020 chipset Format: @@ -829,6 +832,15 @@ and is between 256 and 4096 characters. It is defined in the file hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC) terminal devices. Valid values: 0..8 + hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs. + If specified, z/VM IUCV HVC accepts connections + from listed z/VM user IDs only. + + i2c_bus= [HW] Override the default board specific I2C bus speed + or register an additional I2C bus that is not + registered from board initialization code. + Format: + <bus_id>,<clkrate> i8042.debug [HW] Toggle i8042 debug mode i8042.direct [HW] Put keyboard port into non-translated mode @@ -902,6 +914,15 @@ and is between 256 and 4096 characters. It is defined in the file ihash_entries= [KNL] Set number of hash buckets for inode cache. + ima_audit= [IMA] + Format: { "0" | "1" } + 0 -- integrity auditing messages. (Default) + 1 -- enable informational integrity auditing messages. + + ima_hash= [IMA] + Formt: { "sha1" | "md5" } + default: "sha1" + in2000= [HW,SCSI] See header of drivers/scsi/in2000.c. @@ -1310,8 +1331,13 @@ and is between 256 and 4096 characters. It is defined in the file memtest= [KNL,X86] Enable memtest Format: <integer> - range: 0,4 : pattern number default : 0 <disable> + Specifies the number of memtest passes to be + performed. Each pass selects another test + pattern from a given set of patterns. Memtest + fills the memory with this pattern, validates + memory contents and reserves bad memory + regions that are detected. meye.*= [HW] Set MotionEye Camera parameters See Documentation/video4linux/meye.txt. @@ -1816,11 +1842,6 @@ and is between 256 and 4096 characters. It is defined in the file autoconfiguration. Ranges are in pairs (memory base and size). - dynamic_printk Enables pr_debug()/dev_dbg() calls if - CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. - These can also be switched on/off via - <debugfs>/dynamic_printk/modules - print-fatal-signals= [KNL] debug: print fatal signals print-fatal-signals=1: print segfault info to @@ -2009,15 +2030,6 @@ and is between 256 and 4096 characters. It is defined in the file If enabled at boot time, /selinux/disable can be used later to disable prior to initial policy load. - selinux_compat_net = - [SELINUX] Set initial selinux_compat_net flag value. - Format: { "0" | "1" } - 0 -- use new secmark-based packet controls - 1 -- use legacy packet controls - Default value is 0 (preferred). - Value can be changed at runtime via - /selinux/compat_net. - serialnumber [BUGS=X86-32] shapers= [NET] |