diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 69 |
1 files changed, 56 insertions, 13 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 742f69d18fc8..b7d44871effc 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -472,6 +472,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted. Change the amount of debugging information output when initialising the APIC and IO-APIC components. + apic_extnmi= [APIC,X86] External NMI delivery setting + Format: { bsp (default) | all | none } + bsp: External NMI is delivered only to CPU 0 + all: External NMIs are broadcast to all CPUs as a + backup of CPU 0 + none: External NMI is masked for all CPUs. This is + useful so that a dump capture kernel won't be + shot down by NMI + autoconf= [IPV6] See Documentation/networking/ipv6.txt. @@ -721,16 +730,17 @@ bytes respectively. Such letter suffixes can also be entirely omitted. uart[8250],io,<addr>[,options] uart[8250],mmio,<addr>[,options] + uart[8250],mmio16,<addr>[,options] uart[8250],mmio32,<addr>[,options] uart[8250],0x<addr>[,options] Start an early, polled-mode console on the 8250/16550 UART at the specified I/O port or MMIO address, switching to the matching ttyS device later. MMIO inter-register address stride is either 8-bit - (mmio) or 32-bit (mmio32). - If none of [io|mmio|mmio32], <addr> is assumed to be - equivalent to 'mmio'. 'options' are specified in the - same format described for ttyS above; if unspecified, + (mmio), 16-bit (mmio16), or 32-bit (mmio32). + If none of [io|mmio|mmio16|mmio32], <addr> is assumed + to be equivalent to 'mmio'. 'options' are specified in + the same format described for ttyS above; if unspecified, the h/w is not re-initialized. hvc<n> Use the hypervisor console device <n>. This is for @@ -1002,10 +1012,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted. unspecified, the h/w is not initialized. pl011,<addr> + pl011,mmio32,<addr> Start an early, polled-mode console on a pl011 serial port at the specified address. The pl011 serial port must already be setup and configured. Options are not - yet supported. + yet supported. If 'mmio32' is specified, then only + the driver will use only 32-bit accessors to read/write + the device registers. msm_serial,<addr> Start an early, polled-mode console on an msm serial @@ -2575,8 +2588,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. notsc [BUGS=X86-32] Disable Time Stamp Counter - nousb [USB] Disable the USB subsystem - nowatchdog [KNL] Disable both lockup detectors, i.e. soft-lockup and NMI watchdog (hard-lockup). @@ -3296,18 +3307,35 @@ bytes respectively. Such letter suffixes can also be entirely omitted. rcutorture.verbose= [KNL] Enable additional printk() statements. + rcupdate.rcu_cpu_stall_suppress= [KNL] + Suppress RCU CPU stall warning messages. + + rcupdate.rcu_cpu_stall_timeout= [KNL] + Set timeout for RCU CPU stall warning messages. + rcupdate.rcu_expedited= [KNL] Use expedited grace-period primitives, for example, synchronize_rcu_expedited() instead of synchronize_rcu(). This reduces latency, but can increase CPU utilization, degrade real-time latency, and degrade energy efficiency. - - rcupdate.rcu_cpu_stall_suppress= [KNL] - Suppress RCU CPU stall warning messages. - - rcupdate.rcu_cpu_stall_timeout= [KNL] - Set timeout for RCU CPU stall warning messages. + No effect on CONFIG_TINY_RCU kernels. + + rcupdate.rcu_normal= [KNL] + Use only normal grace-period primitives, + for example, synchronize_rcu() instead of + synchronize_rcu_expedited(). This improves + real-time latency, CPU utilization, and + energy efficiency, but can expose users to + increased grace-period latency. This parameter + overrides rcupdate.rcu_expedited. No effect on + CONFIG_TINY_RCU kernels. + + rcupdate.rcu_normal_after_boot= [KNL] + Once boot has completed (that is, after + rcu_end_inkernel_boot() has been invoked), use + only normal grace-period primitives. No effect + on CONFIG_TINY_RCU kernels. rcupdate.rcu_task_stall_timeout= [KNL] Set timeout in jiffies for RCU task stall warning @@ -3874,6 +3902,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. usbcore.usbfs_snoop= [USB] Set to log all usbfs traffic (default 0 = off). + usbcore.usbfs_snoop_max= + [USB] Maximum number of bytes to snoop in each URB + (default = 65536). + usbcore.blinkenlights= [USB] Set to cycle leds on hubs (default 0 = off). @@ -3894,6 +3926,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. USB_REQ_GET_DESCRIPTOR request in milliseconds (default 5000 = 5.0 seconds). + usbcore.nousb [USB] Disable the USB subsystem + usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. @@ -4114,6 +4148,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted. or other driver-specific files in the Documentation/watchdog/ directory. + workqueue.watchdog_thresh= + If CONFIG_WQ_WATCHDOG is configured, workqueue can + warn stall conditions and dump internal state to + help debugging. 0 disables workqueue stall + detection; otherwise, it's the stall threshold + duration in seconds. The default value is 30 and + it can be updated at runtime by writing to the + corresponding sysfs file. + workqueue.disable_numa By default, all work items queued to unbound workqueues are affine to the NUMA nodes they're |