diff options
Diffstat (limited to 'Documentation/hwmon/w83791d')
| -rw-r--r-- | Documentation/hwmon/w83791d | 43 |
1 files changed, 33 insertions, 10 deletions
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d index a67d3b7a7098..5663e491655c 100644 --- a/Documentation/hwmon/w83791d +++ b/Documentation/hwmon/w83791d @@ -58,29 +58,35 @@ internal state that allows no clean access (Bank with ID register is not currently selected). If you know the address of the chip, use a 'force' parameter; this will put it into a more well-behaved state first. -The driver implements three temperature sensors, five fan rotation speed -sensors, and ten voltage sensors. +The driver implements three temperature sensors, ten voltage sensors, +five fan rotation speed sensors and manual PWM control of each fan. Temperatures are measured in degrees Celsius and measurement resolution is 1 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when the temperature gets higher than the Overtemperature Shutdown value; it stays on until the temperature falls below the Hysteresis value. +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + Fan rotation speeds are reported in RPM (rotations per minute). An alarm is triggered if the rotation speed has dropped below a programmable limit. Fan readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or 128 for all fans) to give the readings more range or accuracy. -Voltage sensors (also known as IN sensors) report their values in millivolts. -An alarm is triggered if the voltage has crossed a programmable minimum -or maximum limit. +Each fan controlled is controlled by PWM. The PWM duty cycle can be read and +set for each fan separately. Valid values range from 0 (stop) to 255 (full). +PWM 1-3 support Thermal Cruise mode, in which the PWMs are automatically +regulated to keep respectively temp 1-3 at a certain target temperature. +See below for the description of the sysfs-interface. The w83791d has a global bit used to enable beeping from the speaker when an alarm is triggered as well as a bitmask to enable or disable the beep for specific alarms. You need both the global beep enable bit and the corresponding beep bit to be on for a triggered alarm to sound a beep. -The sysfs interface to the gloabal enable is via the sysfs beep_enable file. +The sysfs interface to the global enable is via the sysfs beep_enable file. This file is used for both legacy and new code. The sysfs interface to the beep bitmask has migrated from the original legacy @@ -105,6 +111,27 @@ going forward. The driver reads the hardware chip values at most once every three seconds. User mode code requesting values more often will receive cached values. +/sys files +---------- +The sysfs-interface is documented in the 'sysfs-interface' file. Only +chip-specific options are documented here. + +pwm[1-3]_enable - this file controls mode of fan/temperature control for + fan 1-3. Fan/PWM 4-5 only support manual mode. + * 1 Manual mode + * 2 Thermal Cruise mode + * 3 Fan Speed Cruise mode (no further support) + +temp[1-3]_target - defines the target temperature for Thermal Cruise mode. + Unit: millidegree Celsius + RW + +temp[1-3]_tolerance - temperature tolerance for Thermal Cruise mode. + Specifies an interval around the target temperature + in which the fan speed is not changed. + Unit: millidegree Celsius + RW + Alarms bitmap vs. beep_mask bitmask ------------------------------------ For legacy code using the alarms and beep_mask files: @@ -132,7 +159,3 @@ tart2 : alarms: 0x020000 beep_mask: 0x080000 <== mismatch tart3 : alarms: 0x040000 beep_mask: 0x100000 <== mismatch case_open : alarms: 0x001000 beep_mask: 0x001000 global_enable: alarms: -------- beep_mask: 0x800000 (modified via beep_enable) - -W83791D TODO: ---------------- -Provide a patch for smart-fan control (still need appropriate motherboard/fans) |