diff options
Diffstat (limited to 'Documentation/devicetree')
12 files changed, 264 insertions, 75 deletions
diff --git a/Documentation/devicetree/bindings/media/cec-gpio.txt b/Documentation/devicetree/bindings/media/cec-gpio.txt index 12fcd55ed153..47e8d73d32a3 100644 --- a/Documentation/devicetree/bindings/media/cec-gpio.txt +++ b/Documentation/devicetree/bindings/media/cec-gpio.txt @@ -4,8 +4,8 @@ The HDMI CEC GPIO module supports CEC implementations where the CEC line is hooked up to a pull-up GPIO line and - optionally - the HPD line is hooked up to another GPIO line. -Please note: the maximum voltage for the CEC line is 3.63V, for the HPD -line it is 5.3V. So you may need some sort of level conversion circuitry +Please note: the maximum voltage for the CEC line is 3.63V, for the HPD and +5V lines it is 5.3V. So you may need some sort of level conversion circuitry when connecting them to a GPIO line. Required properties: @@ -19,18 +19,24 @@ following property is also required: - hdmi-phandle - phandle to the HDMI controller, see also cec.txt. If the CEC line is not associated with an HDMI receiver/transmitter, then -the following property is optional: +the following property is optional and can be used for debugging HPD changes: - hpd-gpios: gpio that the HPD line is connected to. +This property is optional and can be used for debugging changes on the 5V line: + + - v5-gpios: gpio that the 5V line is connected to. + Example for the Raspberry Pi 3 where the CEC line is connected to -pin 26 aka BCM7 aka CE1 on the GPIO pin header and the HPD line is -connected to pin 11 aka BCM17 (some level shifter is needed for this!): +pin 26 aka BCM7 aka CE1 on the GPIO pin header, the HPD line is +connected to pin 11 aka BCM17 and the 5V line is connected to pin +15 aka BCM22 (some level shifter is needed for the HPD and 5V lines!): #include <dt-bindings/gpio/gpio.h> cec-gpio { - compatible = "cec-gpio"; - cec-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; - hpd-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + compatible = "cec-gpio"; + cec-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + hpd-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + v5-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt new file mode 100644 index 000000000000..aa3e24b41241 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ak7375.txt @@ -0,0 +1,8 @@ +Asahi Kasei Microdevices AK7375 voice coil lens driver + +AK7375 is a camera voice coil lens. + +Mandatory properties: + +- compatible: "asahi-kasei,ak7375" +- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt new file mode 100644 index 000000000000..bd896e9f67d1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt @@ -0,0 +1,46 @@ +* Aptina MT9V111 CMOS sensor +---------------------------- + +The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core +based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP). + +The sensor has an active pixel array of 640x480 pixels and can output a number +of image resolution and formats controllable through a simple two-wires +interface. + +Required properties: +-------------------- + +- compatible: shall be "aptina,mt9v111". +- clocks: reference to the system clock input provider. + +Optional properties: +-------------------- + +- enable-gpios: output enable signal, pin name "OE#". Active low. +- standby-gpios: low power state control signal, pin name "STANDBY". + Active high. +- reset-gpios: chip reset signal, pin name "RESET#". Active low. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: +-------- + + &i2c1 { + camera@48 { + compatible = "aptina,mt9v111"; + reg = <0x48>; + + clocks = <&camera_clk>; + + port { + mt9v111_out: endpoint { + remote-endpoint = <&ceu_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt new file mode 100644 index 000000000000..c4701f1eaaf6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt @@ -0,0 +1,9 @@ +Dongwoon Anatech DW9807 voice coil lens driver + +DW9807 is a 10-bit DAC with current sink capability. It is intended for +controlling voice coil lenses. + +Mandatory properties: + +- compatible: "dongwoon,dw9807-vcm" +- reg: I2C slave address diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt index 33f10a94c381..8ee7c7972ac7 100644 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -29,6 +29,9 @@ Optional properties - reset-gpios: XSHUTDOWN GPIO - flash-leds: See ../video-interfaces.txt - lens-focus: See ../video-interfaces.txt +- rotation: Integer property; valid values are 0 (sensor mounted upright) + and 180 (sensor mounted upside down). See + ../video-interfaces.txt . Endpoint node mandatory properties diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt new file mode 100644 index 000000000000..11e925ed9dad --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt @@ -0,0 +1,46 @@ +* Omnivision OV2680 MIPI CSI-2 sensor + +Required Properties: +- compatible: should be "ovti,ov2680". +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- DOVDD-supply: Digital I/O voltage supply. +- DVDD-supply: Digital core voltage supply. +- AVDD-supply: Analog voltage supply. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the powerdown/reset pin, + if any. This is an active low signal to the OV2680. + +The device node must contain one 'port' child node for its digital output +video port, and this port must have a single endpoint in accordance with + the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0). +- data-lanes: should be set to <1> (one CSI-2 lane supported). + +Example: + +&i2c2 { + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + DOVDD-supply = <&sw2_reg>; + DVDD-supply = <&sw2_reg>; + AVDD-supply = <®_peri_3p15v>; + + port { + ov2680_to_mipi: endpoint { + remote-endpoint = <&mipi_from_sensor>; + clock-lanes = <0>; + data-lanes = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt index 8e36da0d8406..c97c2f2da12d 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -13,6 +13,10 @@ Optional Properties: This is an active low signal to the OV5640. - powerdown-gpios: reference to the GPIO connected to the powerdown pin, if any. This is an active high signal to the OV5640. +- rotation: as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + valid values are 0 (sensor mounted upright) and 180 (sensor + mounted upside down). The device node must contain one 'port' child node for its digital output video port, in accordance with the video interface bindings defined in @@ -51,6 +55,7 @@ Examples: DVDD-supply = <&vgen2_reg>; /* 1.5v */ powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + rotation = <180>; port { /* MIPI CSI-2 bus endpoint */ diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt index 470237ed6fe5..7302e949e662 100644 --- a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt +++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt @@ -27,9 +27,15 @@ Required properties: - sxe - clocks : Must include the following entries: - vde -- resets : Must include the following entries: +- resets : Must contain an entry for each entry in reset-names. +- reset-names : Should include the following entries: - vde +Optional properties: +- resets : Must contain an entry for each entry in reset-names. +- reset-names : Must include the following entries: + - mc + Example: video-codec@6001a000 { @@ -51,5 +57,6 @@ video-codec@6001a000 { <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */ interrupt-names = "sync-token", "bsev", "sxe"; clocks = <&tegra_car TEGRA20_CLK_VDE>; - resets = <&tegra_car 61>; + reset-names = "vde", "mc"; + resets = <&tegra_car 61>, <&mc TEGRA20_MC_RESET_VDE>; }; diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt index cadecebc73f7..09eb6ed99114 100644 --- a/Documentation/devicetree/bindings/media/qcom,camss.txt +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt @@ -5,8 +5,9 @@ Qualcomm Camera Subsystem - compatible: Usage: required Value type: <stringlist> - Definition: Should contain: + Definition: Should contain one of: - "qcom,msm8916-camss" + - "qcom,msm8996-camss" - reg: Usage: required Value type: <prop-encoded-array> @@ -19,11 +20,16 @@ Qualcomm Camera Subsystem - "csiphy0_clk_mux" - "csiphy1" - "csiphy1_clk_mux" + - "csiphy2" (8996 only) + - "csiphy2_clk_mux" (8996 only) - "csid0" - "csid1" + - "csid2" (8996 only) + - "csid3" (8996 only) - "ispif" - "csi_clk_mux" - "vfe0" + - "vfe1" (8996 only) - interrupts: Usage: required Value type: <prop-encoded-array> @@ -34,10 +40,14 @@ Qualcomm Camera Subsystem Definition: Should contain the following entries: - "csiphy0" - "csiphy1" + - "csiphy2" (8996 only) - "csid0" - "csid1" + - "csid2" (8996 only) + - "csid3" (8996 only) - "ispif" - "vfe0" + - "vfe1" (8996 only) - power-domains: Usage: required Value type: <prop-encoded-array> @@ -53,25 +63,42 @@ Qualcomm Camera Subsystem Usage: required Value type: <stringlist> Definition: Should contain the following entries: - - "camss_top_ahb" - - "ispif_ahb" - - "csiphy0_timer" - - "csiphy1_timer" - - "csi0_ahb" - - "csi0" - - "csi0_phy" - - "csi0_pix" - - "csi0_rdi" - - "csi1_ahb" - - "csi1" - - "csi1_phy" - - "csi1_pix" - - "csi1_rdi" - - "camss_ahb" - - "camss_vfe_vfe" - - "camss_csi_vfe" - - "iface" - - "bus" + - "top_ahb" + - "ispif_ahb" + - "csiphy0_timer" + - "csiphy1_timer" + - "csiphy2_timer" (8996 only) + - "csi0_ahb" + - "csi0" + - "csi0_phy" + - "csi0_pix" + - "csi0_rdi" + - "csi1_ahb" + - "csi1" + - "csi1_phy" + - "csi1_pix" + - "csi1_rdi" + - "csi2_ahb" (8996 only) + - "csi2" (8996 only) + - "csi2_phy" (8996 only) + - "csi2_pix" (8996 only) + - "csi2_rdi" (8996 only) + - "csi3_ahb" (8996 only) + - "csi3" (8996 only) + - "csi3_phy" (8996 only) + - "csi3_pix" (8996 only) + - "csi3_rdi" (8996 only) + - "ahb" + - "vfe0" + - "csi_vfe0" + - "vfe0_ahb", (8996 only) + - "vfe0_stream", (8996 only) + - "vfe1", (8996 only) + - "csi_vfe1", (8996 only) + - "vfe1_ahb", (8996 only) + - "vfe1_stream", (8996 only) + - "vfe_ahb" + - "vfe_axi" - vdda-supply: Usage: required Value type: <phandle> @@ -90,22 +117,27 @@ Qualcomm Camera Subsystem - reg: Usage: required Value type: <u32> - Definition: Selects CSI2 PHY interface - PHY0 or PHY1. + Definition: Selects CSI2 PHY interface - PHY0, PHY1 + or PHY2 (8996 only) Endpoint node properties: - clock-lanes: Usage: required Value type: <u32> - Definition: The physical clock lane index. The value - must always be <1> as the physical clock - lane is lane 1. + Definition: The physical clock lane index. On 8916 + the value must always be <1> as the physical + clock lane is lane 1. On 8996 the value must + always be <7> as the hardware supports D-PHY + and C-PHY, indexes are in a common set and + D-PHY physical clock lane is labeled as 7. - data-lanes: Usage: required Value type: <prop-encoded-array> - Definition: An array of physical data lanes indexes. - Position of an entry determines the logical - lane number, while the value of an entry - indicates physical lane index. Lane swapping - is supported. + Definition: An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. Physical lane indexes for + 8916: 0, 2, 3, 4; for 8996: 0, 1, 2, 3. * An Example @@ -161,25 +193,25 @@ Qualcomm Camera Subsystem <&gcc GCC_CAMSS_CSI_VFE0_CLK>, <&gcc GCC_CAMSS_VFE_AHB_CLK>, <&gcc GCC_CAMSS_VFE_AXI_CLK>; - clock-names = "camss_top_ahb", - "ispif_ahb", - "csiphy0_timer", - "csiphy1_timer", - "csi0_ahb", - "csi0", - "csi0_phy", - "csi0_pix", - "csi0_rdi", - "csi1_ahb", - "csi1", - "csi1_phy", - "csi1_pix", - "csi1_rdi", - "camss_ahb", - "camss_vfe_vfe", - "camss_csi_vfe", - "iface", - "bus"; + clock-names = "top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "ahb", + "vfe0", + "csi_vfe0", + "vfe_ahb", + "vfe_axi"; vdda-supply = <&pm8916_l2>; iommus = <&apps_iommu 3>; ports { diff --git a/Documentation/devicetree/bindings/media/qcom,venus.txt b/Documentation/devicetree/bindings/media/qcom,venus.txt index 2693449daf73..00d0d1bf7647 100644 --- a/Documentation/devicetree/bindings/media/qcom,venus.txt +++ b/Documentation/devicetree/bindings/media/qcom,venus.txt @@ -6,6 +6,7 @@ Definition: Value should contain one of: - "qcom,msm8916-venus" - "qcom,msm8996-venus" + - "qcom,sdm845-venus" - reg: Usage: required Value type: <prop-encoded-array> diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index a19517e1c669..2f420050d57f 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -21,7 +21,9 @@ on Gen3 platforms to a CSI-2 receiver. - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7796" for the R8A7796 device + - "renesas,vin-r8a77965" for the R8A77965 device - "renesas,vin-r8a77970" for the R8A77970 device + - "renesas,vin-r8a77995" for the R8A77995 device - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 or RZ/G1 compatible device. @@ -37,30 +39,51 @@ Additionally, an alias named vinX will need to be created to specify which video input device this is. The per-board settings Gen2 platforms: - - port sub-node describing a single endpoint connected to the vin - as described in video-interfaces.txt[1]. Only the first one will - be considered as each vin interface has one input port. + +- port - sub-node describing a single endpoint connected to the VIN + from external SoC pins as described in video-interfaces.txt[1]. + Only the first one will be considered as each vin interface has one + input port. + + - Optional properties for endpoint nodes: + - hsync-active: see [1] for description. Default is active high. + - vsync-active: see [1] for description. Default is active high. + If both HSYNC and VSYNC polarities are not specified, embedded + synchronization is selected. + - field-active-even: see [1] for description. Default is active high. + - bus-width: see [1] for description. The selected bus width depends on + the SoC type and selected input image format. + Valid values are: 8, 10, 12, 16, 24 and 32. + - data-shift: see [1] for description. Valid values are 0 and 8. + - data-enable-active: polarity of CLKENB signal, see [1] for + description. Default is active high. The per-board settings Gen3 platforms: Gen3 platforms can support both a single connected parallel input source -from external SoC pins (port0) and/or multiple parallel input sources -from local SoC CSI-2 receivers (port1) depending on SoC. +from external SoC pins (port@0) and/or multiple parallel input sources +from local SoC CSI-2 receivers (port@1) depending on SoC. - renesas,id - ID number of the VIN, VINx in the documentation. - ports - - port 0 - sub-node describing a single endpoint connected to the VIN - from external SoC pins described in video-interfaces.txt[1]. - Describing more then one endpoint in port 0 is invalid. Only VIN - instances that are connected to external pins should have port 0. - - port 1 - sub-nodes describing one or more endpoints connected to + - port@0 - sub-node describing a single endpoint connected to the VIN + from external SoC pins as described in video-interfaces.txt[1]. + Describing more than one endpoint in port@0 is invalid. Only VIN + instances that are connected to external pins should have port@0. + + Endpoint nodes of port@0 support the optional properties listed in + the Gen2 per-board settings description. + + - port@1 - sub-nodes describing one or more endpoints connected to the VIN from local SoC CSI-2 receivers. The endpoint numbers must use the following schema. - - Endpoint 0 - sub-node describing the endpoint connected to CSI20 - - Endpoint 1 - sub-node describing the endpoint connected to CSI21 - - Endpoint 2 - sub-node describing the endpoint connected to CSI40 - - Endpoint 3 - sub-node describing the endpoint connected to CSI41 + - endpoint@0 - sub-node describing the endpoint connected to CSI20 + - endpoint@1 - sub-node describing the endpoint connected to CSI21 + - endpoint@2 - sub-node describing the endpoint connected to CSI40 + - endpoint@3 - sub-node describing the endpoint connected to CSI41 + + Endpoint nodes of port@1 do not support any optional endpoint property. Device node example for Gen2 platforms -------------------------------------- @@ -107,9 +130,6 @@ Board setup example for Gen2 platforms (vin1 composite video input) status = "okay"; port { - #address-cells = <1>; - #size-cells = <0>; - vin1ep0: endpoint { remote-endpoint = <&adv7180>; bus-width = <8>; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 258b8dfddf48..baf9d9756b3c 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -85,6 +85,10 @@ Optional properties - lens-focus: A phandle to the node of the focus lens controller. +- rotation: The device, typically an image sensor, is not mounted upright, + but a number of degrees counter clockwise. Typical values are 0 and 180 + (upside down). + Optional endpoint properties ---------------------------- @@ -109,6 +113,8 @@ Optional endpoint properties Note, that if HSYNC and VSYNC polarities are not specified, embedded synchronization may be required, where supported. - data-active: similar to HSYNC and VSYNC, specifies data line polarity. +- data-enable-active: similar to HSYNC and VSYNC, specifies the data enable + signal polarity. - field-even-active: field signal level during the even field data transmission. - pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock signal. |