diff options
Diffstat (limited to 'Documentation/devicetree')
9 files changed, 118 insertions, 24 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 04e6bef3ac3f..5fdbbcdf8c4b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -31,6 +31,8 @@ A switch child node has the following optional property: switch. Must be set if the switch can not detect the presence and/or size of a connected EEPROM, otherwise optional. +- reset-gpios : phandle and specifier to a gpio line connected to + reset pin of the switch chip. A switch may have multiple "port" children nodes @@ -114,6 +116,7 @@ Example: #size-cells = <0>; reg = <17 1>; /* MDIO address 17, switch 1 in tree */ mii-bus = <&mii_bus1>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; switch1port0: port@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt index 9c23fdf25018..4a7ede9657b0 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt @@ -1,7 +1,12 @@ Hisilicon MDIO bus controller Properties: -- compatible: "hisilicon,mdio","hisilicon,hns-mdio". +- compatible: can be one of: + "hisilicon,hns-mdio" + "hisilicon,mdio" + "hisilicon,hns-mdio" is recommended to be used for hip05 and later SOCs, + while "hisilicon,mdio" is optional for backwards compatibility only on + hip04 Soc. - reg: The base address of the MDIO bus controller register bank. - #address-cells: Must be <1>. - #size-cells: Must be <0>. MDIO addresses have no size component. diff --git a/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt new file mode 100644 index 000000000000..dea5124cdc52 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt @@ -0,0 +1,18 @@ +* ADF7242 IEEE 802.15.4 * + +Required properties: + - compatible: should be "adi,adf7242" + - spi-max-frequency: maximal bus speed (12.5 MHz) + - reg: the chipselect index + - interrupts: the interrupt generated by the device via pin IRQ1. + IRQ_TYPE_LEVEL_HIGH (4) or IRQ_TYPE_EDGE_FALLING (1) + +Example: + + adf7242@0 { + compatible = "adi,adf7242"; + spi-max-frequency = <10000000>; + reg = <0>; + interrupts = <98 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index b5d79761ac97..5c397ca14cfe 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP available on sama5d3 SoCs. + Use "cdns,np4-macb" for NP4 SoC devices. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". @@ -19,6 +20,9 @@ Required properties: Optional elements: 'tx_clk' - clocks: Phandles to input clocks. +Optional properties for PHY child node: +- reset-gpios : Should specify the gpio for phy reset + Examples: macb0: ethernet@fffc4000 { @@ -29,4 +33,8 @@ Examples: local-mac-address = [3a 0e 03 04 05 06]; clock-names = "pclk", "hclk", "tx_clk"; clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; + ethernet-phy@1 { + reg = <0x1>; + reset-gpios = <&pioE 6 1>; + }; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 692076fda0e5..f9c32adab5c6 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,8 +1,9 @@ Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY -Some boards require special tuning values, particularly when it comes to -clock delays. You can specify clock delay values by adding -micrel-specific properties to an Ethernet OF device node. +Some boards require special tuning values, particularly when it comes +to clock delays. You can specify clock delay values in the PHY OF +device node. Deprecated, but still supported, these properties can +also be added to an Ethernet OF device node. Note that these settings are applied after any phy-specific fixup from phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), @@ -57,16 +58,6 @@ KSZ9031: Examples: - /* Attach to an Ethernet device with autodetected PHY */ - &enet { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - status = "okay"; - }; - - /* Attach to an explicitly-specified PHY */ mdio { phy0: ethernet-phy@0 { rxc-skew-ps = <3000>; diff --git a/Documentation/devicetree/bindings/net/nfc/st95hf.txt b/Documentation/devicetree/bindings/net/nfc/st95hf.txt new file mode 100644 index 000000000000..ea3178bc9ddd --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st95hf.txt @@ -0,0 +1,50 @@ +* STMicroelectronics : NFC Transceiver ST95HF + +ST NFC Transceiver is required to attach with SPI bus. +ST95HF node should be defined in DT as SPI slave device of SPI +master with which ST95HF transceiver is physically connected. +The properties defined below are required to be the part of DT +to include ST95HF transceiver into the platform. + +Required properties: +=================== +- reg: Address of SPI slave "ST95HF transceiver" on SPI master bus. + +- compatible: should be "st,st95hf" for ST95HF NFC transceiver + +- spi-max-frequency: Max. operating SPI frequency for ST95HF + transceiver. + +- enable-gpio: GPIO line to enable ST95HF transceiver. + +- interrupt-parent : Standard way to specify the controller to which + ST95HF transceiver's interrupt is routed. + +- interrupts : Standard way to define ST95HF transceiver's out + interrupt. + +Optional property: +================= +- st95hfvin-supply : This is an optional property. It contains a + phandle to ST95HF transceiver's regulator supply node in DT. + +Example: +======= +spi@9840000 { + reg = <0x9840000 0x110>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pio0 4>; + status = "okay"; + + st95hf@0{ + reg = <0>; + compatible = "st,st95hf"; + status = "okay"; + spi-max-frequency = <1000000>; + enable-gpio = <&pio4 0>; + interrupt-parent = <&pio0>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index b486f3f5f6a3..81a9f9e6b45f 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -5,8 +5,18 @@ interface contains. Required properties: - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC. + "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC. "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC. "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC. + "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface. + "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of (1) the register block and (2) the stream buffer. - interrupts: A list of interrupt-specifiers, one for each entry in interrupt-names. @@ -37,7 +47,7 @@ Optional properties: Example: ethernet@e6800000 { - compatible = "renesas,etheravb-r8a7795"; + compatible = "renesas,etheravb-r8a7795", "renesas,etheravb-rcar-gen3"; reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 3a9d67951606..72d82d684342 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -11,6 +11,8 @@ Required properties: designware version numbers documented in stmmac.txt - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. + - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock + for ptp ref clk. This affects all emacs as the clock is common. Optional properties: altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index f34fc3c81a75..e862a922bd3f 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -35,18 +35,18 @@ Optional properties: - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given - max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock and - the second clock should be peripheral's register interface clock. Further - clocks may be specified in derived bindings. -- clock-names: One name for each entry in the clocks property, the - first one should be "stmmaceth" and the second one should be "pclk". -- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is - available this clock is used for programming the Timestamp Addend Register. - If not passed then the system clock will be used and this is fine on some - platforms. +- clocks: If present, the first clock should be the GMAC main clock + The optional second clock should be peripheral's register interface clock. + The third optional clock should be the ptp reference clock. + Further clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property. + The first one should be "stmmaceth". + The optional second one should be "pclk". + The optional third one should be "clk_ptp_ref". - snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory +- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: @@ -65,4 +65,11 @@ Examples: tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: ethernet-phy@0 { + }; + }; }; |