diff options
Diffstat (limited to 'Documentation/devicetree')
15 files changed, 599 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/media/cec.txt b/Documentation/devicetree/bindings/media/cec.txt new file mode 100644 index 000000000000..22d7aae3d3d7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec.txt @@ -0,0 +1,8 @@ +Common bindings for HDMI CEC adapters + +- hdmi-phandle: phandle to the HDMI controller. + +- needs-hpd: if present the CEC support is only available when the HPD + is high. Some boards only let the CEC pin through if the HPD is high, + for example if there is a level converter that uses the HPD to power + up or down. diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt index 4da486f96ff6..552b6a82cb1f 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7180.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt @@ -6,6 +6,8 @@ digital interfaces like MIPI CSI-2 or parallel video. Required Properties : - compatible : value must be one of "adi,adv7180" + "adi,adv7180cp" + "adi,adv7180st" "adi,adv7182" "adi,adv7280" "adi,adv7280-m" @@ -15,6 +17,19 @@ Required Properties : "adi,adv7282" "adi,adv7282-m" +Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one +'port' child node per device input and output port, in accordance with the +video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port +nodes are numbered as follows. + + Port adv7180cp adv7180st +------------------------------------------------------------------- + Input 0-2 0-5 + Output 3 6 + +The digital output port node must contain at least one endpoint. + Optional Properties : - powerdown-gpios: reference to the GPIO connected to the powerdown pin, if any. diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt new file mode 100644 index 000000000000..02b4e9cd7b1b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt @@ -0,0 +1,59 @@ +Maxim Integrated MAX2175 RF to Bits tuner +----------------------------------------- + +The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with +RF to BitsĀ® front-end designed for software-defined radio solutions. + +Required properties: +-------------------- +- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner. +- clocks: clock specifier. +- port: child port node corresponding to the I2S output, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional properties: +-------------------- +- maxim,master : phandle to the master tuner if it is a slave. This + is used to define two tuners in diversity mode + (1 master, 1 slave). By default each tuner is an + individual master. +- maxim,refout-load : load capacitance value (in picofarads) on reference + output drive level. The possible load values are: + 0 (default - refout disabled) + 10 + 20 + 30 + 40 + 60 + 70 +- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used + in this hardware for AM antenna input. + +Example: +-------- + +Board specific DTS file + +/* Fixed XTAL clock node */ +maxim_xtal: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <36864000>; +}; + +/* A tuner device instance under i2c bus */ +max2175_0: tuner@60 { + compatible = "maxim,max2175"; + reg = <0x60>; + clocks = <&maxim_xtal>; + maxim,refout-load = <10>; + + port { + max2175_0_ep: endpoint { + remote-endpoint = <&slave_rx_device>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt new file mode 100644 index 000000000000..540b36c4b1f2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -0,0 +1,45 @@ +* Omnivision OV5640 MIPI CSI-2 sensor + +Required Properties: +- compatible: should be "ovti,ov5640" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". +- DOVDD-supply: Digital I/O voltage supply, 1.8 volts +- AVDD-supply: Analog voltage supply, 2.8 volts +- DVDD-supply: Digital core voltage supply, 1.5 volts + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the reset pin, if any. + This is an active low signal to the OV5640. +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, + if any. This is an active high signal to the OV5640. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + + port { + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt new file mode 100644 index 000000000000..77f4b0a7fd2b --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx.txt @@ -0,0 +1,53 @@ +Freescale i.MX Media Video Device +================================= + +Video Media Controller node +--------------------------- + +This is the media controller node for video capture support. It is a +virtual device that lists the camera serial interface nodes that the +media device will control. + +Required properties: +- compatible : "fsl,imx-capture-subsystem"; +- ports : Should contain a list of phandles pointing to camera + sensor interface ports of IPU devices + +example: + +capture-subsystem { + compatible = "fsl,imx-capture-subsystem"; + ports = <&ipu1_csi0>, <&ipu1_csi1>; +}; + + +mipi_csi2 node +-------------- + +This is the device node for the MIPI CSI-2 Receiver core in the i.MX +SoC. This is a Synopsys Designware MIPI CSI-2 host controller core +combined with a D-PHY core mixed into the same register block. In +addition this device consists of an i.MX-specific "CSI2IPU gasket" +glue logic, also controlled from the same register block. The CSI2IPU +gasket demultiplexes the four virtual channel streams from the host +controller's 32-bit output image bus onto four 16-bit parallel busses +to the i.MX IPU CSIs. + +Required properties: +- compatible : "fsl,imx6-mipi-csi2"; +- reg : physical base address and length of the register set; +- clocks : the MIPI CSI-2 receiver requires three clocks: hsi_tx + (the D-PHY clock), video_27m (D-PHY PLL reference + clock), and eim_podf; +- clock-names : must contain "dphy", "ref", "pix"; +- port@* : five port nodes must exist, containing endpoints + connecting to the source and sink devices according to + of_graph bindings. The first port is an input port, + connecting with a MIPI CSI-2 source, and ports 1 + through 4 are output ports connecting with parallel + bus sink endpoint nodes and correspond to the four + MIPI CSI-2 virtual channel outputs. + +Optional properties: +- interrupts : must contain two level-triggered interrupts, + in order: 100 and 101; diff --git a/Documentation/devicetree/bindings/media/mediatek-mdp.txt b/Documentation/devicetree/bindings/media/mediatek-mdp.txt index 4182063a54db..0d03e3ae2be2 100644 --- a/Documentation/devicetree/bindings/media/mediatek-mdp.txt +++ b/Documentation/devicetree/bindings/media/mediatek-mdp.txt @@ -2,7 +2,7 @@ Media Data Path is used for scaling and color space conversion. -Required properties (controller (parent) node): +Required properties (controller node): - compatible: "mediatek,mt8173-mdp" - mediatek,vpu: the node of video processor unit, see Documentation/devicetree/bindings/media/mediatek-vpu.txt for details. @@ -32,21 +32,16 @@ Required properties (DMA function blocks, child node): for details. Example: -mdp { - compatible = "mediatek,mt8173-mdp"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - mediatek,vpu = <&vpu>; - mdp_rdma0: rdma@14001000 { compatible = "mediatek,mt8173-mdp-rdma"; + "mediatek,mt8173-mdp"; reg = <0 0x14001000 0 0x1000>; clocks = <&mmsys CLK_MM_MDP_RDMA0>, <&mmsys CLK_MM_MUTEX_32K>; power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; iommus = <&iommu M4U_PORT_MDP_RDMA0>; mediatek,larb = <&larb0>; + mediatek,vpu = <&vpu>; }; mdp_rdma1: rdma@14002000 { @@ -106,4 +101,3 @@ mdp { iommus = <&iommu M4U_PORT_MDP_WROT1>; mediatek,larb = <&larb4>; }; -}; diff --git a/Documentation/devicetree/bindings/media/qcom,venus.txt b/Documentation/devicetree/bindings/media/qcom,venus.txt new file mode 100644 index 000000000000..2693449daf73 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,venus.txt @@ -0,0 +1,107 @@ +* Qualcomm Venus video encoder/decoder accelerators + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain one of: + - "qcom,msm8916-venus" + - "qcom,msm8996-venus" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base address and length of the register map. +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain interrupt line number. +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: A List of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required for msm8916 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Core video accelerator clock + - "iface" Video accelerator AHB clock + - "bus" Video accelerator AXI clock +- clock-names: + Usage: required for msm8996 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Core video accelerator clock + - "iface" Video accelerator AHB clock + - "bus" Video accelerator AXI clock + - "mbus" Video MAXI clock +- power-domains: + Usage: required + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the peripheral. +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the firmware + memory region. + +* Subnodes +The Venus video-codec node must contain two subnodes representing +video-decoder and video-encoder. + +Every of video-encoder or video-decoder subnode should have: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain "venus-decoder" or "venus-encoder" +- clocks: + Usage: required for msm8996 + Value type: <prop-encoded-array> + Definition: A List of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required for msm8996 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Subcore video accelerator clock + +- power-domains: + Usage: required for msm8996 + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the subcore. + +* An Example + video-codec@1d00000 { + compatible = "qcom,msm8916-venus"; + reg = <0x01d00000 0xff000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_VENUS0_VCODEC0_CLK>, + <&gcc GCC_VENUS0_AHB_CLK>, + <&gcc GCC_VENUS0_AXI_CLK>; + clock-names = "core", "iface", "bus"; + power-domains = <&gcc VENUS_GDSC>; + iommus = <&apps_iommu 5>; + memory-region = <&venus_mem>; + + video-decoder { + compatible = "venus-decoder"; + clocks = <&mmcc VIDEO_SUBCORE0_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE0_GDSC>; + }; + + video-encoder { + compatible = "venus-encoder"; + clocks = <&mmcc VIDEO_SUBCORE1_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE1_GDSC>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 6a4e61cbe011..6e4ef8caf759 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -1,5 +1,5 @@ -Renesas RCar Video Input driver (rcar_vin) ------------------------------------------- +Renesas R-Car Video Input driver (rcar_vin) +------------------------------------------- The rcar_vin device provides video input capabilities for the Renesas R-Car family of devices. The current blocks are always slaves and suppot one input diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt new file mode 100644 index 000000000000..39516b94c28f --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt @@ -0,0 +1,176 @@ +Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) +------------------------------------------------------------ + +R-Car Gen3 DRIF is a SPI like receive only slave device. A general +representation of DRIF interfacing with a master device is shown below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| |-----SD0------->|D0 | +| |-----SD1------->|D1 | ++---------------------+ +---------------------+ + +As per datasheet, each DRIF channel (drifn) is made up of two internal +channels (drifn0 & drifn1). These two internal channels share the common +CLK & SYNC. Each internal channel has its own dedicated resources like +irq, dma channels, address space & clock. This internal split is not +visible to the external master device. + +The device tree model represents each internal channel as a separate node. +The internal channels sharing the CLK & SYNC are tied together by their +phandles using a property called "renesas,bonding". For the rest of +the documentation, unless explicitly stated, the word channel implies an +internal channel. + +When both internal channels are enabled they need to be managed together +as one (i.e.) they cannot operate alone as independent devices. Out of the +two, one of them needs to act as a primary device that accepts common +properties of both the internal channels. This channel is identified by a +property called "renesas,primary-bond". + +To summarize, + - When both the internal channels that are bonded together are enabled, + the zeroth channel is selected as primary-bond. This channels accepts + properties common to all the members of the bond. + - When only one of the bonded channels need to be enabled, the property + "renesas,bonding" or "renesas,primary-bond" will have no effect. That + enabled channel can act alone as any other independent device. + +Required properties of an internal channel: +------------------------------------------- +- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. + "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of that channel. +- interrupts: associated with that channel. +- clocks: phandle and clock specifier of that channel. +- clock-names: clock input name string: "fck". +- dmas: phandles to the DMA channels. +- dma-names: names of the DMA channel: "rx". +- renesas,bonding: phandle to the other channel. + +Optional properties of an internal channel: +------------------------------------------- +- power-domains: phandle to the respective power domain. + +Required properties of an internal channel when: + - It is the only enabled channel of the bond (or) + - If it acts as primary among enabled bonds +-------------------------------------------------------- +- pinctrl-0: pin control group to be used for this channel. +- pinctrl-names: must be "default". +- renesas,primary-bond: empty property indicating the channel acts as primary + among the bonded channels. +- port: child port node corresponding to the data input, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional endpoint property: +--------------------------- +- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. + This property maps to SYNCAC bit in the hardware manual. The + default is 1 (active high). + +Example: +-------- + +(1) Both internal channels enabled: +----------------------------------- + +When interfacing with a third party tuner device with two data pins as shown +below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| |-----SD0------->|D0 | +| |-----SD1------->|D1 | ++---------------------+ +---------------------+ + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + renesas,primary-bond; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + }; + }; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + }; + + +(2) Internal channel 1 alone is enabled: +---------------------------------------- + +When interfacing with a third party tuner device with one data pin as shown +below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| | |D0 (unused) | +| |-----SD-------->|D1 | ++---------------------+ +---------------------+ + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + sync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt index 4bb08d9d940b..1b1a10ba48ce 100644 --- a/Documentation/devicetree/bindings/media/s5p-cec.txt +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -15,7 +15,11 @@ Required properties: - clock-names : from common clock binding: must contain "hdmicec", corresponding to entry in the clocks property. - samsung,syscon-phandle - phandle to the PMU system controller - - hdmi-phandle - phandle to the HDMI controller + - hdmi-phandle - phandle to the HDMI controller, see also cec.txt. + +Optional: + - needs-hpd : if present the CEC support is only available when the HPD + is high. See cec.txt for more details. Example: diff --git a/Documentation/devicetree/bindings/media/st,stm32-cec.txt b/Documentation/devicetree/bindings/media/st,stm32-cec.txt new file mode 100644 index 000000000000..6be2381c180d --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-cec.txt @@ -0,0 +1,19 @@ +STMicroelectronics STM32 CEC driver + +Required properties: + - compatible : value should be "st,stm32-cec" + - reg : Physical base address of the IP registers and length of memory + mapped region. + - clocks : from common clock binding: handle to CEC clocks + - clock-names : from common clock binding: must be "cec" and "hdmi-cec". + - interrupts : CEC interrupt number to the CPU. + +Example for stm32f746: + +cec: cec@40006c00 { + compatible = "st,stm32-cec"; + reg = <0x40006C00 0x400>; + interrupts = <94>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(CEC)>, <&rcc 1 CLK_HDMI_CEC>; + clock-names = "cec", "hdmi-cec"; +}; diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt new file mode 100644 index 000000000000..249790a93017 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt @@ -0,0 +1,45 @@ +STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) + +Required properties: +- compatible: "st,stm32-dcmi" +- reg: physical base address and length of the registers set for the device +- interrupts: should contain IRQ line for the DCMI +- resets: reference to a reset controller, + see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property +- clock-names: must contain "mclk", which is the DCMI peripherial clock +- pinctrl: the pincontrol settings to configure muxing properly + for pins that connect to DCMI device. + See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt. +- dmas: phandle to DMA controller node, + see Documentation/devicetree/bindings/dma/stm32-dma.txt +- dma-names: must contain "tx", which is the transmit channel from DCMI to DMA + +DCMI supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + dcmi: dcmi@50050000 { + compatible = "st,stm32-dcmi"; + reg = <0x50050000 0x400>; + interrupts = <78>; + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>; + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>; + clock-names = "mclk"; + pinctrl-names = "default"; + pinctrl-0 = <&dcmi_pins>; + dmas = <&dma2 1 1 0x414 0x3>; + dma-names = "tx"; + port { + dcmi_0: endpoint { + remote-endpoint = <...>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/stih-cec.txt b/Documentation/devicetree/bindings/media/stih-cec.txt index 289a08b33651..8be2a040c6c6 100644 --- a/Documentation/devicetree/bindings/media/stih-cec.txt +++ b/Documentation/devicetree/bindings/media/stih-cec.txt @@ -9,7 +9,7 @@ Required properties: - pinctrl-names: Contains only one value - "default" - pinctrl-0: Specifies the pin control groups used for CEC hardware. - resets: Reference to a reset controller - - hdmi-phandle: Phandle to the HDMI controller + - hdmi-phandle: Phandle to the HDMI controller, see also cec.txt. Example for STIH407: diff --git a/Documentation/devicetree/bindings/media/video-mux.txt b/Documentation/devicetree/bindings/media/video-mux.txt new file mode 100644 index 000000000000..63b9dc913e45 --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-mux.txt @@ -0,0 +1,60 @@ +Video Multiplexer +================= + +Video multiplexers allow to select between multiple input ports. Video received +on the active input port is passed through to the output port. Muxes described +by this binding are controlled by a multiplexer controller that is described by +the bindings in Documentation/devicetree/bindings/mux/mux-controller.txt + +Required properties: +- compatible : should be "video-mux" +- mux-controls : mux controller node to use for operating the mux +- #address-cells: should be <1> +- #size-cells: should be <0> +- port@*: at least three port nodes containing endpoints connecting to the + source and sink devices according to of_graph bindings. The last port is + the output port, all others are inputs. + +Optionally, #address-cells, #size-cells, and port nodes can be grouped under a +ports node as described in Documentation/devicetree/bindings/graph.txt. + +Example: + + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + + video-mux { + compatible = "video-mux"; + mux-controls = <&mux>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mux_in0: endpoint { + remote-endpoint = <&video_source0_out>; + }; + }; + + port@1 { + reg = <1>; + + mux_in1: endpoint { + remote-endpoint = <&video_source1_out>; + }; + }; + + port@2 { + reg = <2>; + + mux_out: endpoint { + remote-endpoint = <&capture_interface_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt index 0849618a9df0..45ce054d844d 100644 --- a/Documentation/devicetree/bindings/property-units.txt +++ b/Documentation/devicetree/bindings/property-units.txt @@ -30,6 +30,7 @@ Electricity -micro-ohms : micro Ohms -microwatt-hours: micro Watt-hours -microvolt : micro volts +-picofarads : picofarads Temperature ---------------------------------------- |