diff options
Diffstat (limited to 'Documentation/devicetree')
19 files changed, 439 insertions, 39 deletions
diff --git a/Documentation/devicetree/bindings/arc/pmu.txt b/Documentation/devicetree/bindings/arc/pmu.txt new file mode 100644 index 000000000000..49d517340de3 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/pmu.txt @@ -0,0 +1,24 @@ +* ARC Performance Monitor Unit + +The ARC 700 can be configured with a pipeline performance monitor for counting +CPU and cache events like cache misses and hits. + +Note that: + * ARC 700 refers to a family of ARC processor cores; + - There is only one type of PMU available for the whole family; + - The PMU may support different sets of events; supported events are probed + at boot time, as required by the reference manual. + + * The ARC 700 PMU does not support interrupts; although HW events may be + counted, the HW events themselves cannot serve as a trigger for a sample. + +Required properties: + +- compatible : should contain + "snps,arc700-pmu" + +Example: + +pmu { + compatible = "snps,arc700-pmu"; +}; diff --git a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt index f770ac0893d4..049675944b78 100644 --- a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt +++ b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt @@ -1,7 +1,9 @@ Calxeda DDR memory controller Properties: -- compatible : Should be "calxeda,hb-ddr-ctrl" +- compatible : Should be: + - "calxeda,hb-ddr-ctrl" for ECX-1000 + - "calxeda,ecx-2000-ddr-ctrl" for ECX-2000 - reg : Address and size for DDR controller registers. - interrupts : Interrupt for DDR controller. diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index e1f343c7a34b..f69bcf5a6343 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -28,7 +28,7 @@ The three cells in order are: dependent: - bit 7-0: peripheral identifier for the hardware handshaking interface. The identifier can be different for tx and rx. - - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 1 for ASAP. + - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 2 for ASAP. Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt new file mode 100644 index 000000000000..1b87b741fa8e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-bcm-kona.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 000000000000..056732cfdcee --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,44 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt new file mode 100644 index 000000000000..897cfcd5ce92 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -0,0 +1,23 @@ +I2C for R-Car platforms + +Required properties: +- compatible: Must be one of + "renesas,i2c-rcar" + "renesas,i2c-r8a7778" + "renesas,i2c-r8a7779" + "renesas,i2c-r8a7790" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@e6500000 { + compatible = "renesas,i2c-rcar-h2"; + reg = <0 0xe6500000 0 0x428>; + interrupts = <0 174 0x4>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 000000000000..437e0db3823c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&CLK_S_ICN_REG_0>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index c98e5a2934d8..b1cb3415e6f1 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -15,6 +15,7 @@ adi,adt7461 +/-1C TDM Extended Temp Range I.C adt7461 +/-1C TDM Extended Temp Range I.C at,24c08 i2c serial eeprom (24cxx) atmel,24c02 i2c serial eeprom (24cxx) +atmel,at97sc3204t i2c trusted platform module (TPM) catalyst,24c32 i2c serial eeprom dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock dallas,ds1338 I2C RTC with 56-Byte NV RAM @@ -45,6 +46,7 @@ mc,rv3029c2 Real Time Clock Module with I2C-Bus national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface +nuvoton,npct501 i2c trusted platform module (TPM) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar @@ -62,3 +64,4 @@ taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor +winbond,wpct301 i2c trusted platform module (TPM) diff --git a/Documentation/devicetree/bindings/media/st-rc.txt b/Documentation/devicetree/bindings/media/st-rc.txt new file mode 100644 index 000000000000..05c432d08bca --- /dev/null +++ b/Documentation/devicetree/bindings/media/st-rc.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for ST IRB IP + +Required properties: + - compatible: Should contain "st,comms-irb". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - rx-mode: can be "infrared" or "uhf". This property specifies the L1 + protocol used for receiving remote control signals. rx-mode should + be present iff the rx pins are wired up. + - tx-mode: should be "infrared". This property specifies the L1 + protocol used for transmitting remote control signals. tx-mode should + be present iff the tx pins are wired up. + +Optional properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing + properly for IRB pins. + - clocks : phandle with clock-specifier pair for IRB. + +Example node: + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 1dd622546d06..9046ba06c47a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -12,6 +12,11 @@ Required properties: Optional properties: - fsl,cd-controller : Indicate to use controller internal card detection - fsl,wp-controller : Indicate to use controller internal write protection +- fsl,delay-line : Specify the number of delay cells for override mode. + This is used to set the clock delay for DLL(Delay Line) on override mode + to select a proper data sampling window in case the clock quality is not good + due to signal path is too long on the board. Please refer to eSDHC/uSDHC + chapter, DLL (Delay Line) section in RM for details. Examples: diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 066a78b034ca..8f3f13315358 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -52,6 +52,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. +* clock-freq-min-max: Minimum and Maximum clock frequency for card output + clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value @@ -66,6 +69,10 @@ Optional properties: * supports-highspeed: Enables support for high speed cards (up to 50MHz) +* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode + +* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode + * broken-cd: as documented in mmc core bindings. * vmmc-supply: The phandle to the regulator to use for vmmc. If this is @@ -93,8 +100,10 @@ board specific portions as listed below. dwmmc0@12200000 { clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; num-slots = <1>; supports-highspeed; + caps2-mmc-hs200-1_8v; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt new file mode 100644 index 000000000000..d5c706216df5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/twl-charger.txt @@ -0,0 +1,20 @@ +TWL BCI (Battery Charger Interface) + +Required properties: +- compatible: + - "ti,twl4030-bci" +- interrupts: two interrupt lines from the TWL SIH (secondary + interrupt handler) - interrupts 9 and 2. + +Optional properties: +- ti,bb-uvolt: microvolts for charging the backup battery. +- ti,bb-uamp: microamps for charging the backup battery. + +Examples: + +bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt new file mode 100644 index 000000000000..4f6a550184d0 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt @@ -0,0 +1,32 @@ +TI BQ24735 Charge Controller +~~~~~~~~~~ + +Required properties : + - compatible : "ti,bq24735" + +Optional properties : + - interrupts : Specify the interrupt to be used to trigger when the AC + adapter is either plugged in or removed. + - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter + presence. This is a Host GPIO that is configured as an input and + connected to the bq24735. + - ti,charge-current : Used to control and set the charging current. This value + must be between 128mA and 8.128A with a 64mA step resolution. The POR value + is 0x0000h. This number is in mA (e.g. 8192), see spec for more information + about the ChargeCurrent (0x14h) register. + - ti,charge-voltage : Used to control and set the charging voltage. This value + must be between 1.024V and 19.2V with a 16mV step resolution. The POR value + is 0x0000h. This number is in mV (e.g. 19200), see spec for more information + about the ChargeVoltage (0x15h) register. + - ti,input-current : Used to control and set the charger input current. This + value must be between 128mA and 8.064A with a 128mA step resolution. The + POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for + more information about the InputCurrent (0x3fh) register. + +Example: + + bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + } diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt index 2a4b4bce6110..7fc1b010fa75 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -1,33 +1,30 @@ -* Freescale 83xx DMA Controller +* Freescale DMA Controllers -Freescale PowerPC 83xx have on chip general purpose DMA controllers. +** Freescale Elo DMA Controller + This is a little-endian 4-channel DMA controller, used in Freescale mpc83xx + series chips such as mpc8315, mpc8349, mpc8379 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" -- reg : <registers mapping for DMA general status reg> -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- compatible : must include "fsl,elo-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - cell-index : controller index. 0 for controller @ 0x8100 -- interrupts : <interrupt mapping for DMA IRQ> +- interrupts : interrupt specifier for DMA IRQ - interrupt-parent : optional, if needed for interrupt mapping - - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel". However, see note below. - - reg : <registers mapping for channel> - - cell-index : dma channel index starts at 0. + - compatible : must include "fsl,elo-dma-channel" + However, see note below. + - reg : DMA channel specific registers + - cell-index : DMA channel index starts at 0. Optional properties: - - interrupts : <interrupt mapping for DMA channel IRQ> - (on 83xx this is expected to be identical to - the interrupts property of the parent node) + - interrupts : interrupt specifier for DMA channel IRQ + (on 83xx this is expected to be identical to + the interrupts property of the parent node) - interrupt-parent : optional, if needed for interrupt mapping Example: @@ -70,30 +67,27 @@ Example: }; }; -* Freescale 85xx/86xx DMA Controller - -Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. +** Freescale EloPlus DMA Controller + This is a 4-channel DMA controller with extended addresses and chaining, + mainly used in Freescale mpc85xx/86xx, Pxxx and BSC series chips, such as + mpc8540, mpc8641 p4080, bsc9131 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" -- reg : <registers mapping for DMA general status reg> +- compatible : must include "fsl,eloplus-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels - cell-index : controller index. 0 for controller @ 0x21000, 1 for controller @ 0xc000 -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel". However, see note below. - - cell-index : dma channel index starts at 0. - - reg : <registers mapping for channel> - - interrupts : <interrupt mapping for DMA channel IRQ> + - compatible : must include "fsl,eloplus-dma-channel" + However, see note below. + - cell-index : DMA channel index starts at 0. + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ - interrupt-parent : optional, if needed for interrupt mapping Example: @@ -134,6 +128,76 @@ Example: }; }; +** Freescale Elo3 DMA Controller + DMA controller which has same function as EloPlus except that Elo3 has 8 + channels while EloPlus has only 4, it is used in Freescale Txxx and Bxxx + series chips, such as t1040, t4240, b4860. + +Required properties: + +- compatible : must include "fsl,elo3-dma" +- reg : contains two entries for DMA General Status Registers, + i.e. DGSR0 which includes status for channel 1~4, and + DGSR1 for channel 5~8 +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller + +- DMA channel nodes: + - compatible : must include "fsl,eloplus-dma-channel" + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ + - interrupt-parent : optional, if needed for interrupt mapping + +Example: +dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elo3-dma"; + reg = <0x100300 0x4>, + <0x100600 0x4>; + ranges = <0x0 0x100100 0x500>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + interrupts = <31 2 0 0>; + }; + dma-channel@300 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x300 0x80>; + interrupts = <76 2 0 0>; + }; + dma-channel@380 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x380 0x80>; + interrupts = <77 2 0 0>; + }; + dma-channel@400 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x400 0x80>; + interrupts = <78 2 0 0>; + }; + dma-channel@480 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x480 0x80>; + interrupts = <79 2 0 0>; + }; +}; + Note on DMA channel compatible properties: The compatible property must say "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA driver (fsldma). Any DMA channel used by fsldma cannot be used by another diff --git a/Documentation/devicetree/bindings/watchdog/dw_wdt.txt b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt new file mode 100644 index 000000000000..08e16f684f2d --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt @@ -0,0 +1,21 @@ +Synopsys Designware Watchdog Timer + +Required Properties: + +- compatible : Should contain "snps,dw-wdt" +- reg : Base address and size of the watchdog timer registers. +- clocks : phandle + clock-specifier for the clock that drives the + watchdog timer. + +Optional Properties: + +- interrupts : The interrupt used for the watchdog timeout warning. + +Example: + + watchdog0: wd@ffd02000 { + compatible = "snps,dw-wdt"; + reg = <0xffd02000 0x1000>; + interrupts = <0 171 4>; + clocks = <&per_base_clk>; + }; diff --git a/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt index 370dee3226d9..370dee3226d9 100644 --- a/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt diff --git a/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt new file mode 100644 index 000000000000..1169857d1d12 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt @@ -0,0 +1,15 @@ +MOXA ART Watchdog timer + +Required properties: + +- compatible : Must be "moxa,moxart-watchdog" +- reg : Should contain registers location and length +- clocks : Should contain phandle for the clock that drives the counter + +Example: + + watchdog: watchdog@98500000 { + compatible = "moxa,moxart-watchdog"; + reg = <0x98500000 0x10>; + clocks = <&coreclk>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt new file mode 100644 index 000000000000..d7bab3db9d1f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt @@ -0,0 +1,19 @@ +Ralink Watchdog Timers + +Required properties: +- compatible: must be "ralink,rt2880-wdt" +- reg: physical base address of the controller and length of the register range + +Optional properties: +- interrupt-parent: phandle to the INTC device node +- interrupts: Specify the INTC interrupt number + +Example: + + watchdog@120 { + compatible = "ralink,rt2880-wdt"; + reg = <0x120 0x10>; + + interrupt-parent = <&intc>; + interrupts = <1>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt new file mode 100644 index 000000000000..9cbc76c89b2b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt @@ -0,0 +1,14 @@ +SiRFSoC Timer and Watchdog Timer(WDT) Controller + +Required properties: +- compatible: "sirf,prima2-tick" +- reg: Address range of tick timer/WDT register set +- interrupts: interrupt number to the cpu + +Example: + +timer@b0020000 { + compatible = "sirf,prima2-tick"; + reg = <0xb0020000 0x1000>; + interrupts = <0>; +}; |