diff options
Diffstat (limited to 'Documentation/devicetree')
9 files changed, 285 insertions, 30 deletions
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt new file mode 100644 index 000000000000..e7caefa0b9c2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt @@ -0,0 +1,109 @@ +MediaTek XS-PHY binding +-------------------------- + +The XS-PHY controller supports physical layer functionality for USB3.1 +GEN2 controller on MediaTek SoCs. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy", + soc-model is the name of SoC, such as mt3611 etc; + when using "mediatek,xsphy" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt3611-xsphy" + + - #address-cells, #size-cells : should use the same values as the root node + - ranges: must be present + +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple U3 ports, + exclude port's private register, if only U2 ports provided, + shouldn't use the property. + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate + calibrate + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on + SoC process + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeedPlus analog phy, sometimes is + 24M, 25M or 27M, depended on platform. +- #phy-cells : should be 1 + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +The following optional properties are only for debug or HQA test +Optional properties (PHY_TYPE_USB2 port (child) node): +- mediatek,eye-src : u32, the value of slew rate calibrate +- mediatek,eye-vrt : u32, the selection of VRT reference voltage +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage +- mediatek,efuse-intr : u32, the selection of Internal Resistor + +Optional properties (PHY_TYPE_USB3 port (child) node): +- mediatek,efuse-intr : u32, the selection of Internal Resistor +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance + +Banks layout of xsphy +------------------------------------------------------------- +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u2 port2 0x2000 MISC + ... +u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB +u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN +u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + +DIG_GLB & PHYA_GLB are shared by U31 ports. + +Example: + +u3phy: usb-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0 0x11c43000 0 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0 0x11c40000 0 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0 0x11c43400 0 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index dcf1b8f691d5..266a1bb8bb6e 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -9,7 +9,8 @@ Required properties: "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, - "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy. + "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. - reg: offset and length of register set for PHY's common serdes block. diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt index 42c97426836e..03025d97998b 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. Required properties: - compatible: compatible list, contains "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY. + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. - reg: offset and length of the PHY register set. - #phy-cells: must be 0. @@ -27,6 +27,27 @@ Optional properties: tuning parameter value for qusb2 phy. - qcom,tcsr-syscon: Phandle to TCSR syscon register region. + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY + tuning parameter that may vary for different boards of same SOC. + This property is applicable to only QUSB2 v2 PHY (sdm845). + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX + output current. + Possible range is - 15mA to 24mA (stepsize of 600 uA). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 22.2mA for sdm845. + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level. + Possible range is 0 to 15% (stepsize of 5%). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 10% for sdm845. +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX + pre-emphasis (specified using qcom,preemphasis-level) must be in + effect. Duration could be half-bit of full-bit. + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is full-bit width for sdm845. Example: hsusb_phy: phy@7411000 { diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 0e03344e2e8b..2e9318151df7 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -76,6 +76,10 @@ Optional properties: needs to make sure it does not send more than 90% maximum_periodic_data_per_frame. The use case is multiple transactions, but less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -102,4 +106,6 @@ Example: rx-burst-size-dword = <0x10>; extcon = <0>, <&usb_id>; phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0dbd3083e7dd..7f13ebef06cb 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -7,6 +7,26 @@ Required properties: - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. + - clock-names: should contain "ref", "bus_early", "suspend" + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "amlogic,meson-axg-dwc3" + "amlogic,meson-gxl-dwc3" + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" Optional properties: - usb-phy : array of phandle for the PHY device. The first element @@ -15,6 +35,7 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" or "usb3-phy". + - resets: a single pair of phandle and reset specifier - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 472facfa5a71..6087dc7f209e 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -6,12 +6,6 @@ Required properties : - interrupts : Interrupt specifier Optional properties : -- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink -- fcs,max-sink-microamp : Maximum current to negotiate when configured as sink -- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink - If this is less then max-sink-microvolt * - max-sink-microamp then the configured current will - be clamped. - fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink when negotiating diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt new file mode 100644 index 000000000000..f4633496b122 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt @@ -0,0 +1,45 @@ +HiSilicon STB xHCI + +The device node for HiSilicon STB xHCI host controller + +Required properties: + - compatible: should be "hisilicon,hi3798cv200-xhci" + - reg: specifies physical base address and size of the registers + - interrupts : interrupt used by the controller + - clocks: a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names: must contain + "bus": for bus clock + "utmi": for utmi clock + "pipe": for pipe clock + "suspend": for suspend clock + - resets: a list of phandle and reset specifier pairs as listed in + reset-names property. + - reset-names: must contain + "soft": for soft reset + - phys: a list of phandle + phy specifier pairs + - phy-names: must contain at least one of following: + "inno": for inno phy + "combo": for combo phy + +Optional properties: + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - imod-interval-ns: default interrupt moderation interval is 40000ns + +Example: + +xhci0: xchi@f98a0000 { + compatible = "hisilicon,hi3798cv200-xhci"; + reg = <0xf98a0000 0x10000>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_USB3_BUS_CLK>, + <&crg HISTB_USB3_UTMI_CLK>, + <&crg HISTB_USB3_PIPE_CLK>, + <&crg HISTB_USB3_SUSPEND_CLK>; + clock-names = "bus", "utmi", "pipe", "suspend"; + resets = <&crg 0xb0 12>; + reset-names = "soft"; + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>; + phy-names = "inno", "combo"; +}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index bc8a2fa5d2bf..95afdcf3c337 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -1,54 +1,95 @@ Qualcomm SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: should contain "qcom,dwc3" +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node - clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names -- clock-names: Should contain the following: +- clock-names: Should contain the following: "core" Master/Core clock, have to be >= 125 MHz for SS operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). Optional clocks: - "iface" System bus AXI clock. Not present on all platforms - "sleep" Sleep clock, used when USB3 core goes into low - power mode (U3). + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. Required child node: A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY Example device nodes: hs_phy: phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qusb2-v2-phy"; + ... }; ss_phy: phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qmp-v3-usb3-phy"; + ... }; - usb3_0: usb30@0 { + usb3_0: usb30@a6f8800 { compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; #address-cells = <1>; #size-cells = <1>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - ranges; + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; dwc3@10000000 { compatible = "snps,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt new file mode 100644 index 000000000000..09e847e92e5e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -0,0 +1,17 @@ +Richtek RT1711H TypeC PD Controller. + +Required properties: + - compatible : Must be "richtek,rt1711h". + - reg : Must be 0x4e, it's slave address of RT1711H. + - interrupt-parent : the phandle for the interrupt controller that + provides interrupts for this device. + - interrupts : <a b> where a is the interrupt number and b represents an + encoding of the sense and level information for the interrupt. + +Example : +rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + interrupt-parent = <&gpio26>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +}; |