diff options
Diffstat (limited to 'Documentation/devicetree')
41 files changed, 601 insertions, 42 deletions
diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt index 4408af693d0c..6f44df94101c 100644 --- a/Documentation/devicetree/bindings/dma/stm32-dma.txt +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -71,7 +71,7 @@ channel: a phandle to the DMA controller plus the following four integer cells: Example: usart1: serial@40011000 { - compatible = "st,stm32-usart", "st,stm32-uart"; + compatible = "st,stm32-uart"; reg = <0x40011000 0x400>; interrupts = <37>; clocks = <&clk_pclk2>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt index 439a7430fc68..439a7430fc68 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt diff --git a/Documentation/devicetree/bindings/hwmon/max1619.txt b/Documentation/devicetree/bindings/hwmon/max1619.txt new file mode 100644 index 000000000000..c70dbbe1e56f --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/max1619.txt @@ -0,0 +1,12 @@ +Bindings for MAX1619 Temperature Sensor + +Required properties: +- compatible : "maxim,max1619" +- reg : I2C address, one of 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, or + 0x4d, 0x4e + +Example: + temp@4c { + compatible = "maxim,max1619"; + reg = <0x4c>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/max31785.txt b/Documentation/devicetree/bindings/hwmon/max31785.txt new file mode 100644 index 000000000000..106e08c56aaa --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/max31785.txt @@ -0,0 +1,22 @@ +Bindings for the Maxim MAX31785 Intelligent Fan Controller +========================================================== + +Reference: + +https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf + +The Maxim MAX31785 is a PMBus device providing closed-loop, multi-channel fan +management with temperature and remote voltage sensing. Various fan control +features are provided, including PWM frequency control, temperature hysteresis, +dual tachometer measurements, and fan health monitoring. + +Required properties: +- compatible : One of "maxim,max31785" or "maxim,max31785a" +- reg : I2C address, one of 0x52, 0x53, 0x54, 0x55. + +Example: + + fans@52 { + compatible = "maxim,max31785"; + reg = <0x52>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt index bcd3ac8e6e0c..7d64753df949 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt @@ -29,15 +29,29 @@ Required properties: "microchip,mcp3204" "microchip,mcp3208" "microchip,mcp3301" + "microchip,mcp3550-50" + "microchip,mcp3550-60" + "microchip,mcp3551" + "microchip,mcp3553" NOTE: The use of the compatibles with no vendor prefix is deprecated and only listed because old DT use them. + - spi-cpha, spi-cpol (boolean): + Either SPI mode (0,0) or (1,1) must be used, so specify + none or both of spi-cpha, spi-cpol. The MCP3550/1/3 + is more efficient in mode (1,1) as only 3 instead of + 4 bytes need to be read from the ADC, but not all SPI + masters support it. + + - vref-supply: Phandle to the external reference voltage supply. + Examples: spi_controller { mcp3x0x@0 { compatible = "mcp3002"; reg = <0>; spi-max-frequency = <1000000>; + vref-supply = <&vref_reg>; }; }; diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt index 64dc4843c180..0df9befdaecc 100644 --- a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -12,6 +12,7 @@ for the Thermal Controller which holds a phandle to the AUXADC. Required properties: - compatible: Should be one of: - "mediatek,mt2701-auxadc": For MT2701 family of SoCs + - "mediatek,mt2712-auxadc": For MT2712 family of SoCs - "mediatek,mt7622-auxadc": For MT7622 family of SoCs - "mediatek,mt8173-auxadc": For MT8173 family of SoCs - reg: Address range of the AUXADC unit. diff --git a/Documentation/devicetree/bindings/iio/dac/ds4424.txt b/Documentation/devicetree/bindings/iio/dac/ds4424.txt new file mode 100644 index 000000000000..eaebbf8dab40 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ds4424.txt @@ -0,0 +1,20 @@ +Maxim Integrated DS4422/DS4424 7-bit Sink/Source Current DAC Device Driver + +Datasheet publicly available at: +https://datasheets.maximintegrated.com/en/ds/DS4422-DS4424.pdf + +Required properties: + - compatible: Should be one of + maxim,ds4422 + maxim,ds4424 + - reg: Should contain the DAC I2C address + +Optional properties: + - vcc-supply: Power supply is optional. If not defined, driver will ignore it. + +Example: + ds4224@10 { + compatible = "maxim,ds4424"; + reg = <0x10>; /* When A0, A1 pins are ground */ + vcc-supply = <&vcc_3v3>; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/ti-dac082s085.txt b/Documentation/devicetree/bindings/iio/dac/ti-dac082s085.txt new file mode 100644 index 000000000000..9cb0e10df704 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti-dac082s085.txt @@ -0,0 +1,34 @@ +Texas Instruments 8/10/12-bit 2/4-channel DAC driver + +Required properties: + - compatible: Must be one of: + "ti,dac082s085" + "ti,dac102s085" + "ti,dac122s085" + "ti,dac084s085" + "ti,dac104s085" + "ti,dac124s085" + - reg: Chip select number. + - spi-cpha, spi-cpol: SPI mode (0,1) or (1,0) must be used, so specify + either spi-cpha or spi-cpol (but not both). + - vref-supply: Phandle to the external reference voltage supply. + +For other required and optional properties of SPI slave nodes please refer to +../../spi/spi-bus.txt. + +Example: + vref_2v5_reg: regulator-vref { + compatible = "regulator-fixed"; + regulator-name = "2v5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + dac@0 { + compatible = "ti,dac082s085"; + reg = <0>; + spi-max-frequency = <40000000>; + spi-cpol; + vref-supply = <&vref_2v5_reg>; + }; diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt index 295a9edfa4fd..8d8176459d09 100644 --- a/Documentation/devicetree/bindings/iio/health/max30100.txt +++ b/Documentation/devicetree/bindings/iio/health/max30100.txt @@ -20,9 +20,9 @@ Optional properties: Example: -max30100@057 { +max30100@57 { compatible = "maxim,max30100"; - reg = <57>; + reg = <0x57>; maxim,led-current-microamp = <24000 50000>; interrupt-parent = <&gpio1>; interrupts = <16 2>; diff --git a/Documentation/devicetree/bindings/iio/health/max30102.txt b/Documentation/devicetree/bindings/iio/health/max30102.txt index c695e7cbeefb..8629c18b0e78 100644 --- a/Documentation/devicetree/bindings/iio/health/max30102.txt +++ b/Documentation/devicetree/bindings/iio/health/max30102.txt @@ -20,7 +20,7 @@ Optional properties: Example: -max30100@57 { +max30102@57 { compatible = "maxim,max30102"; reg = <0x57>; maxim,red-led-current-microamp = <7000>; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index 9ec6f5ce54fc..6f626f73417e 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -46,6 +46,8 @@ Accelerometers: - st,h3lis331dl-accel - st,lng2dm-accel - st,lis3l02dq +- st,lis2dw12 +- st,lis3dhh Gyroscopes: - st,l3g4200d-gyro @@ -71,3 +73,5 @@ Pressure sensors: - st,lps25h-press - st,lps331ap-press - st,lps22hb-press +- st,lps33hw +- st,lps35hw diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt new file mode 100644 index 000000000000..a83f9a5734ca --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -0,0 +1,36 @@ +Amlogic meson GPIO interrupt controller + +Meson SoCs contains an interrupt controller which is able to watch the SoC +pads and generate an interrupt on edge or level. The controller is essentially +a 256 pads to 8 GIC interrupt multiplexer, with a filter block to select edge +or level and polarity. It does not expose all 256 mux inputs because the +documentation shows that the upper part is not mapped to any pad. The actual +number of interrupt exposed depends on the SoC. + +Required properties: + +- compatible : must have "amlogic,meson8-gpio-intc” and either + “amlogic,meson8-gpio-intc” for meson8 SoCs (S802) or + “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or + “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or + “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912) +- interrupt-parent : a phandle to the GIC the interrupts are routed to. + Usually this is provided at the root level of the device tree as it is + common to most of the SoC. +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 2. +- meson,channel-interrupts: Array with the 8 upstream hwirq numbers. These + are the hwirqs used on the parent interrupt controller. + +Example: + +gpio_interrupt: interrupt-controller@9880 { + compatible = "amlogic,meson-gxbb-gpio-intc", + "amlogic,meson-gpio-intc"; + reg = <0x0 0x9880 0x0 0x10>; + interrupt-controller; + #interrupt-cells = <2>; + meson,channel-interrupts = <64 65 66 67 68 69 70 71>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 5eb108e180fa..0a57f2f4167d 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -75,6 +75,10 @@ These nodes must have the following properties: - reg: Specifies the base physical address and size of the ITS registers. +Optional: +- socionext,synquacer-pre-its: (u32, u32) tuple describing the untranslated + address and size of the pre-ITS window. + The main GIC node must contain the appropriate #address-cells, #size-cells and ranges properties for the reg property of all ITS nodes. diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt index 448273a30a11..36df06c5c567 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt @@ -2,7 +2,8 @@ Broadcom Generic Level 2 Interrupt Controller Required properties: -- compatible: should be "brcm,l2-intc" +- compatible: should be "brcm,l2-intc" for latched interrupt controllers + should be "brcm,bcm7271-l2-intc" for level interrupt controllers - reg: specifies the base physical address and size of the registers - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/openrisc,ompic.txt b/Documentation/devicetree/bindings/interrupt-controller/openrisc,ompic.txt new file mode 100644 index 000000000000..caec07cc7149 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/openrisc,ompic.txt @@ -0,0 +1,22 @@ +Open Multi-Processor Interrupt Controller + +Required properties: + +- compatible : This should be "openrisc,ompic" +- reg : Specifies base physical address and size of the register space. The + size is based on the number of cores the controller has been configured + to handle, this should be set to 8 bytes per cpu core. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : This should be set to 0 as this will not be an irq + parent. +- interrupts : Specifies the interrupt line to which the ompic is wired. + +Example: + +ompic: interrupt-controller@98000000 { + compatible = "openrisc,ompic"; + reg = <0x98000000 16>; + interrupt-controller; + #interrupt-cells = <0>; + interrupts = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index e3f052d8c11a..33c9a10fdc91 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -13,6 +13,9 @@ Required properties: - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) - "renesas,intc-ex-r8a7795" (R-Car H3) + - "renesas,intc-ex-r8a7796" (R-Car M3-W) + - "renesas,intc-ex-r8a77970" (R-Car V3M) + - "renesas,intc-ex-r8a77995" (R-Car D3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory - clocks: Must contain a reference to the functional clock. diff --git a/Documentation/devicetree/bindings/interrupt-controller/socionext,synquacer-exiu.txt b/Documentation/devicetree/bindings/interrupt-controller/socionext,synquacer-exiu.txt new file mode 100644 index 000000000000..8b2faefe29ca --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/socionext,synquacer-exiu.txt @@ -0,0 +1,32 @@ +Socionext SynQuacer External Interrupt Unit (EXIU) + +The Socionext Synquacer SoC has an external interrupt unit (EXIU) +that forwards a block of 32 configurable input lines to 32 adjacent +level-high type GICv3 SPIs. + +Required properties: + +- compatible : Should be "socionext,synquacer-exiu". +- reg : Specifies base physical address and size of the + control registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : phandle of the GIC these interrupts are routed to. +- socionext,spi-base : The SPI number of the first SPI of the 32 adjacent + ones the EXIU forwards its interrups to. + +Notes: + +- Only SPIs can use the EXIU as an interrupt parent. + +Example: + + exiu: interrupt-controller@510c0000 { + compatible = "socionext,synquacer-exiu"; + reg = <0x0 0x510c0000 0x0 0x20>; + interrupt-controller; + interrupt-parent = <&gic>; + #interrupt-cells = <3>; + socionext,spi-base = <112>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt index 6e7703d4ff5b..edf03f09244b 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -2,7 +2,9 @@ STM32 External Interrupt Controller Required properties: -- compatible: Should be "st,stm32-exti" +- compatible: Should be: + "st,stm32-exti" + "st,stm32h7-exti" - reg: Specifies base physical address and size of the registers - interrupt-controller: Indentifies the node as an interrupt controller - #interrupt-cells: Specifies the number of cells to encode an interrupt diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt new file mode 100644 index 000000000000..8765c605e6bc --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt @@ -0,0 +1,54 @@ +* Amlogic Meson6, Meson8 and Meson8b SDIO/MMC controller + +The highspeed MMC host controller on Amlogic SoCs provides an interface +for MMC, SD, SDIO and SDHC types of memory cards. + +Supported maximum speeds are the ones of the eMMC standard 4.41 as well +as the speed of SD standard 2.0. + +The hardware provides an internal "mux" which allows up to three slots +to be controlled. Only one slot can be accessed at a time. + +Required properties: + - compatible : must be one of + - "amlogic,meson8-sdio" + - "amlogic,meson8b-sdio" + along with the generic "amlogic,meson-mx-sdio" + - reg : mmc controller base registers + - interrupts : mmc controller interrupt + - #address-cells : must be 1 + - size-cells : must be 0 + - clocks : phandle to clock providers + - clock-names : must contain "core" and "clkin" + +Required child nodes: +A node for each slot provided by the MMC controller is required. +NOTE: due to a driver limitation currently only one slot (= child node) + is supported! + +Required properties on each child node (= slot): + - compatible : must be "mmc-slot" (see mmc.txt within this directory) + - reg : the slot (or "port") ID + +Optional properties on each child node (= slot): + - bus-width : must be 1 or 4 (8-bit bus is not supported) + - for cd and all other additional generic mmc parameters + please refer to mmc.txt within this directory + +Examples: + mmc@c1108c20 { + compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio"; + reg = <0xc1108c20 0x20>; + interrupts = <0 28 1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; + clock-names = "core", "clkin"; + + slot@1 { + compatible = "mmc-slot"; + reg = <1>; + + bus-width = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index b32ade645ad9..94a90b49a692 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -53,6 +53,9 @@ Optional properties: - no-sdio: controller is limited to send sdio cmd during initialization - no-sd: controller is limited to send sd cmd during initialization - no-mmc: controller is limited to send mmc cmd during initialization +- fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. + The value <n> is the driver type as specified in the eMMC specification + (table 206 in spec version 5.1). *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index 4182ea36ca5b..72d2a734ab85 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -7,10 +7,18 @@ This file documents differences between the core properties in mmc.txt and the properties used by the msdc driver. Required properties: -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc" +- compatible: value should be either of the following. + "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 + "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 + "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 +- reg: physical base address of the controller and length - interrupts: Should contain MSDC interrupt number -- clocks: MSDC source clock, HCLK -- clock-names: "source", "hclk" +- clocks: Should contain phandle for the clock feeding the MMC controller +- clock-names: Should contain the following: + "source" - source clock (required) + "hclk" - HCLK which used for host (required) + "source_cg" - independent source clock gate (required for MT2712) - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl @@ -30,6 +38,10 @@ Optional properties: - mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection If present,HS400 command responses are sampled on rising edges. If not present,HS400 command responses are sampled on falling edges. +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc + error caused by stop clock(fifo full) + Valid range = [0:0x7]. if not present, default value is 0. + applied to compatible "mediatek,mt2701-mmc". Examples: mmc0: mmc@11230000 { diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt index de2c53cff4f1..3ee9263adf73 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt @@ -15,6 +15,8 @@ Required properties: Optional properties: - vqmmc-supply: phandle to the regulator device tree node, mentioned as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host + requires the CMD_DAT_DELAY control to be enabled. Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 0576264eab5e..bfdcdc4ccdff 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -18,6 +18,8 @@ Required properties: "core" - SDC MMC clock (MCLK) (required) "bus" - SDCC bus voter clock (optional) "xo" - TCXO clock (optional) + "cal" - reference clock for RCLK delay calibration (optional) + "sleep" - sleep clock for RCLK delay calibration (optional) Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt new file mode 100644 index 000000000000..51775a372c06 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -0,0 +1,16 @@ +* TI OMAP SDHCI Controller + +Refer to mmc.txt for standard MMC bindings. + +Required properties: +- compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers +- ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + +Example: + mmc1: mmc@4809c000 { + compatible = "ti,dra7-sdhci"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 54ef642f23a0..3c6762430fd9 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -10,7 +10,7 @@ described in mmc.txt, can be used. Additionally the following tmio_mmc-specific optional bindings can be used. Required properties: -- compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit +- compatible: should contain one or more of the following: "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC @@ -26,6 +26,16 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller + "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller + "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 + SDHI controller + "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller + + + When compatible with the generic version, nodes must list + the SoC-specific version corresponding to the platform + first followed by the generic version. - clocks: Most controllers only have 1 clock source per channel. However, on some variations of this controller, the internal card detection @@ -43,3 +53,61 @@ Optional properties: - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl + +Example: R8A7790 (R-Car H2) SDHI controller nodes + + sdhi0: sd@ee100000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee100000 0 0x328>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 314>; + dmas = <&dmac0 0xcd>, <&dmac0 0xce>, + <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 314>; + status = "disabled"; + }; + + sdhi1: sd@ee120000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee120000 0 0x328>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 313>; + dmas = <&dmac0 0xc9>, <&dmac0 0xca>, + <&dmac1 0xc9>, <&dmac1 0xca>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 313>; + status = "disabled"; + }; + + sdhi2: sd@ee140000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee140000 0 0x100>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 312>; + dmas = <&dmac0 0xc1>, <&dmac0 0xc2>, + <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 312>; + status = "disabled"; + }; + + sdhi3: sd@ee160000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee160000 0 0x100>; + interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 311>; + dmas = <&dmac0 0xd3>, <&dmac0 0xd4>, + <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 311>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/openrisc/opencores/or1ksim.txt b/Documentation/devicetree/bindings/openrisc/opencores/or1ksim.txt new file mode 100644 index 000000000000..4950c794ecbb --- /dev/null +++ b/Documentation/devicetree/bindings/openrisc/opencores/or1ksim.txt @@ -0,0 +1,39 @@ +OpenRISC Generic SoC +==================== + +Boards and FPGA SoC's which support the OpenRISC standard platform. The +platform essentially follows the conventions of the OpenRISC architecture +specification, however some aspects, such as the boot protocol have been defined +by the Linux port. + +Required properties +------------------- + - compatible: Must include "opencores,or1ksim" + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required for at least CPU 0. Since the topology may +be probed via CPS, it is not necessary to specify secondary CPUs. Required +properties: + - compatible: Must be "opencores,or1200-rtlsvn481". + - reg: CPU number. + - clock-frequency: The CPU clock frequency in Hz. +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "opencores,or1200-rtlsvn481"; + reg = <0>; + clock-frequency = <20000000>; + }; + }; + + +Boot protocol +------------- +The bootloader may pass the following arguments to the kernel: + - r3: address of a flattened device-tree blob or 0x0. diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index 0f2a6f8fcafd..27717e816e71 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,8 +1,9 @@ -* Dialog Semiconductor DA9211/DA9212/DA9213/DA9214/DA9215 Voltage Regulator +* Dialog Semiconductor DA9211/DA9212/DA9213/DA9223/DA9214/DA9224/DA9215/DA9225 + Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" - or "dlg,da9214" or "dlg,da9215" +- compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" or "dlg,da9223" + or "dlg,da9214" or "dlg,da9224" or "dlg,da9215" or "dlg,da9225" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -16,7 +17,6 @@ Optional properties: - Any optional property defined in regulator.txt Example 1) DA9211 - pmic: da9211@68 { compatible = "dlg,da9211"; reg = <0x68>; @@ -35,7 +35,6 @@ Example 1) DA9211 }; Example 2) DA9212 - pmic: da9212@68 { compatible = "dlg,da9212"; reg = <0x68>; @@ -79,7 +78,25 @@ Example 3) DA9213 }; }; -Example 4) DA9214 +Example 4) DA9223 + pmic: da9223@68 { + compatible = "dlg,da9223"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; + }; + }; + +Example 5) DA9214 pmic: da9214@68 { compatible = "dlg,da9214"; reg = <0x68>; @@ -105,7 +122,33 @@ Example 4) DA9214 }; }; -Example 5) DA9215 +Example 6) DA9224 + pmic: da9224@68 { + compatible = "dlg,da9224"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; + +Example 7) DA9215 pmic: da9215@68 { compatible = "dlg,da9215"; reg = <0x68>; @@ -131,3 +174,28 @@ Example 5) DA9215 }; }; +Example 8) DA9225 + pmic: da9225@68 { + compatible = "dlg,da9225"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index 444c47831a40..c6dd3f5e485b 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -21,7 +21,7 @@ Each regulator is defined using the standard binding for regulators. Example 1: PFUZE100 - pmic: pfuze100@08 { + pmic: pfuze100@8 { compatible = "fsl,pfuze100"; reg = <0x08>; @@ -122,7 +122,7 @@ Example 1: PFUZE100 Example 2: PFUZE200 - pmic: pfuze200@08 { + pmic: pfuze200@8 { compatible = "fsl,pfuze200"; reg = <0x08>; @@ -216,7 +216,7 @@ Example 2: PFUZE200 Example 3: PFUZE3000 - pmic: pfuze3000@08 { + pmic: pfuze3000@8 { compatible = "fsl,pfuze3000"; reg = <0x08>; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 0fa3b0fac129..57d2c65899df 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -8,6 +8,7 @@ Qualcomm SPMI Regulators "qcom,pm8916-regulators" "qcom,pm8941-regulators" "qcom,pm8994-regulators" + "qcom,pmi8994-regulators" - interrupts: Usage: optional @@ -100,6 +101,15 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_l1-supply: + Usage: optional (pmi8994 only) + Value type: <phandle> + Definition: Reference to regulator supplying the input pin, as + described in the data sheet. + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each @@ -122,6 +132,9 @@ pm8994: l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 +pmi8994: + s1, s2, s3, l1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt - with additional custom properties described below: diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index e6e6142e33ac..7c0d6b2f53e4 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -24,6 +24,7 @@ Optional properties: - dma-names: "rx" for RX channel, "tx" for TX channel. - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO capable USARTs. +- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt <chip> compatible description: - at91rm9200: legacy USART support diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 574c3a2c77d5..860a9559839a 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -9,6 +9,7 @@ Optional properties: - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. +- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt Please check Documentation/devicetree/bindings/serial/serial.txt for the complete list of generic properties. diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index a1252a047f78..59567b51cf09 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -16,6 +16,7 @@ Required properties: Optional properties: - dmas: A list of two dma specifiers, one for each entry in dma-names. - dma-names: should contain "tx" and "rx". +- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt Note: Optional properties for DMA support. Write them both or both not. diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index 7a71b5de77d6..43eac675f21f 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -19,6 +19,7 @@ Optional properties: - dmas : DMA specifier, consisting of a phandle to the DMA controller node and a DMA channel number. - dma-names : "rx" for receive channel, "tx" for transmit channel. +- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt Example: diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt index 3657f9f9d17a..d150b04a6229 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -2,14 +2,10 @@ Required properties: - compatible: can be either: - - "st,stm32-usart", - "st,stm32-uart", - - "st,stm32f7-usart", - "st,stm32f7-uart", - - "st,stm32h7-usart" - "st,stm32h7-uart". - depending on whether the device supports synchronous mode - and is compatible with stm32(f4), stm32f7 or stm32h7. + depending is compatible with stm32(f4), stm32f7 or stm32h7. - reg: The address and length of the peripheral registers space - interrupts: - The interrupt line for the USART instance, @@ -33,7 +29,7 @@ usart4: serial@40004c00 { }; usart2: serial@40004400 { - compatible = "st,stm32-usart", "st,stm32-uart"; + compatible = "st,stm32-uart"; reg = <0x40004400 0x400>; interrupts = <38>; clocks = <&clk_pclk1>; @@ -43,7 +39,7 @@ usart2: serial@40004400 { }; usart1: serial@40011000 { - compatible = "st,stm32-usart", "st,stm32-uart"; + compatible = "st,stm32-uart"; reg = <0x40011000 0x400>; interrupts = <37>; clocks = <&rcc 0 164>; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index e865855726a2..bdd83959019c 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,7 +1,9 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,msiof-r8a7790" (R-Car H2) +- compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) @@ -10,7 +12,7 @@ Required properties: "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) - "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device) + "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) "renesas,sh-msiof" (deprecated) diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index f5916c92fe91..1925277bfc1e 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -24,6 +24,16 @@ Required properties: based on a specific SoC configuration. - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle + For 66AK2G this property should be set per binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +SoC-specific Required Properties: + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the SPI device id + value. This property is as per the binding, Optional: - cs-gpios: gpio chip selects diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 8f4169f63936..3b02b3a7cfb2 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -5,11 +5,14 @@ Required properties: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. For Renesas Serial Peripheral Interface on RZ/A1H: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. - For Quad Serial Peripheral Interface on R-Car Gen2: + For Quad Serial Peripheral Interface on R-Car Gen2 and + RZ/G1 devices: "renesas,qspi-<soctype>", "renesas,qspi" as fallback. Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) - "renesas,qspi-r8a7792" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt new file mode 100644 index 000000000000..8de589b376ce --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt @@ -0,0 +1,58 @@ +Spreadtrum ADI controller + +ADI is the abbreviation of Anolog-Digital interface, which is used to access +analog chip (such as PMIC) from digital chip. ADI controller follows the SPI +framework for its hardware implementation is alike to SPI bus and its timing +is compatile to SPI timing. + +ADI controller has 50 channels including 2 software read/write channels and +48 hardware channels to access analog chip. For 2 software read/write channels, +users should set ADI registers to access analog chip. For hardware channels, +we can configure them to allow other hardware components to use it independently, +which means we can just link one analog chip address to one hardware channel, +then users can access the mapped analog chip address by this hardware channel +triggered by hardware components instead of ADI software channels. + +Thus we introduce one property named "sprd,hw-channels" to configure hardware +channels, the first value specifies the hardware channel id which is used to +transfer data triggered by hardware automatically, and the second value specifies +the analog chip address where user want to access by hardware components. + +Since we have multi-subsystems will use unique ADI to access analog chip, when +one system is reading/writing data by ADI software channels, that should be under +one hardware spinlock protection to prevent other systems from reading/writing +data by ADI software channels at the same time, or two parallel routine of setting +ADI registers will make ADI controller registers chaos to lead incorrect results. +Then we need one hardware spinlock to synchronize between the multiple subsystems. + +Required properties: +- compatible: Should be "sprd,sc9860-adi". +- reg: Offset and length of ADI-SPI controller register space. +- hwlocks: Reference to a phandle of a hwlock provider node. +- hwlock-names: Reference to hwlock name strings defined in the same order + as the hwlocks, should be "adi". +- #address-cells: Number of cells required to define a chip select address + on the ADI-SPI bus. Should be set to 1. +- #size-cells: Size of cells required to define a chip select address size + on the ADI-SPI bus. Should be set to 0. + +Optional properties: +- sprd,hw-channels: This is an array of channel values up to 49 channels. + The first value specifies the hardware channel id which is used to + transfer data triggered by hardware automatically, and the second + value specifies the analog chip address where user want to access + by hardware components. + +SPI slave nodes must be children of the SPI controller node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + adi_bus: spi@40030000 { + compatible = "sprd,sc9860-adi"; + reg = <0 0x40030000 0 0x10000>; + hwlocks = <&hwlock1 0>; + hwlock-names = "adi"; + #address-cells = <1>; + #size-cells = <0>; + sprd,hw-channels = <30 0x8c20>; + }; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index 6ca6b9e582a0..d740989eb569 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -20,16 +20,16 @@ Required Properties: (CMT1 on sh73a0 and r8a7740) This is a fallback for the above renesas,cmt-48-* entries. - - "renesas,cmt0-r8a73a4" for the 32-bit CMT0 device included in r8a73a4. - - "renesas,cmt1-r8a73a4" for the 48-bit CMT1 device included in r8a73a4. - - "renesas,cmt0-r8a7790" for the 32-bit CMT0 device included in r8a7790. - - "renesas,cmt1-r8a7790" for the 48-bit CMT1 device included in r8a7790. - - "renesas,cmt0-r8a7791" for the 32-bit CMT0 device included in r8a7791. - - "renesas,cmt1-r8a7791" for the 48-bit CMT1 device included in r8a7791. - - "renesas,cmt0-r8a7793" for the 32-bit CMT0 device included in r8a7793. - - "renesas,cmt1-r8a7793" for the 48-bit CMT1 device included in r8a7793. - - "renesas,cmt0-r8a7794" for the 32-bit CMT0 device included in r8a7794. - - "renesas,cmt1-r8a7794" for the 48-bit CMT1 device included in r8a7794. + - "renesas,r8a73a4-cmt0" for the 32-bit CMT0 device included in r8a73a4. + - "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4. + - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790. + - "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790. + - "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791. + - "renesas,r8a7791-cmt1" for the 48-bit CMT1 device included in r8a7791. + - "renesas,r8a7793-cmt0" for the 32-bit CMT0 device included in r8a7793. + - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793. + - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. + - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2. - "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2. @@ -46,7 +46,7 @@ Required Properties: Example: R8A7790 (R-Car H2) CMT0 and CMT1 nodes cmt0: timer@ffca0000 { - compatible = "renesas,cmt0-r8a7790", "renesas,rcar-gen2-cmt0"; + compatible = "renesas,r8a7790-cmt0", "renesas,rcar-gen2-cmt0"; reg = <0 0xffca0000 0 0x1004>; interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>, <0 142 IRQ_TYPE_LEVEL_HIGH>; @@ -55,7 +55,7 @@ Example: R8A7790 (R-Car H2) CMT0 and CMT1 nodes }; cmt1: timer@e6130000 { - compatible = "renesas,cmt1-r8a7790", "renesas,rcar-gen2-cmt1"; + compatible = "renesas,r8a7790-cmt1", "renesas,rcar-gen2-cmt1"; reg = <0 0xe6130000 0 0x1004>; interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>, <0 121 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index af284fbd4d23..8bcac6ee73da 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -71,6 +71,7 @@ isil,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor isil,isl29030 Intersil ISL29030 Ambient Light and Proximity Sensor maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs +maxim,max6621 PECI-to-I2C translator for PECI-to-SMBus/I2C protocol conversion maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus mcube,mc3230 mCube 3-axis 8-bit digital accelerometer diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 1afd298eddd7..b1eeca851d6f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -246,6 +246,7 @@ onion Onion Corporation onnn ON Semiconductor Corp. ontat On Tat Industrial Company opencores OpenCores.org +openrisc OpenRISC.io option Option NV ORCL Oracle Corporation ortustech Ortus Technology Co., Ltd. |