diff options
Diffstat (limited to 'Documentation/devicetree')
125 files changed, 3257 insertions, 87 deletions
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index c78576bb7729..11d3056dc2bd 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -26,6 +26,10 @@ Raspberry Pi Model B+ Required root node properties: compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; +Raspberry Pi 2 Model B +Required root node properties: +compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; + Raspberry Pi Compute Module Required root node properties: compatible = "raspberrypi,compute-module", "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt index 6b0f49f6f499..8608a776caa7 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt @@ -5,4 +5,11 @@ Boards with the BCM4708 SoC shall have the following properties: Required root node property: +bcm4708 compatible = "brcm,bcm4708"; + +bcm4709 +compatible = "brcm,bcm4709"; + +bcm53012 +compatible = "brcm,bcm53012"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt new file mode 100644 index 000000000000..677ef9d9f445 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt @@ -0,0 +1,39 @@ +Broadcom Northstar Plus SoC CPU Enable Method +--------------------------------------------- +This binding defines the enable method used for starting secondary +CPU in the following Broadcom SoCs: + BCM58522, BCM58525, BCM58535, BCM58622, BCM58623, BCM58625, BCM88312 + +The enable method is specified by defining the following required +properties in the corresponding secondary "cpu" device tree node: + - enable-method = "brcm,bcm-nsp-smp"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register which should hold the common +entry point for a secondary CPU. This entry is cpu node specific +and should be added per cpu. E.g., in case of NSP (BCM58625) which +is a dual core CPU SoC, this entry should be added to cpu1 node. + + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + enable-method = "brcm,bcm-nsp-smp"; + secondary-boot-reg = <0xffff042c>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/compulab-boards.txt b/Documentation/devicetree/bindings/arm/compulab-boards.txt new file mode 100644 index 000000000000..42a10285af9c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/compulab-boards.txt @@ -0,0 +1,25 @@ +CompuLab SB-SOM is a multi-module baseboard capable of carrying: + - CM-T43 + - CM-T54 + - CM-QS600 + - CL-SOM-AM57x + - CL-SOM-iMX7 +modules with minor modifications to the SB-SOM assembly. + +Required root node properties: + - compatible = should be "compulab,sb-som" + +Compulab CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on +Freescale i.MX7 ARM Cortex-A7 System-on-Chip. + +Required root node properties: + - compatible = "compulab,cl-som-imx7", "fsl,imx7d"; + +Compulab SBC-iMX7 is a single board computer based on the +Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with +the CL-SOM-iMX7 System-on-Module providing most of the functions, +and SB-SOM-iMX7 carrier board providing additional peripheral +functions and connectors. + +Required root node properties: + - compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index c352c11bd641..ae9be074d09f 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -191,6 +191,8 @@ nodes to be present and contain the properties described below. "allwinner,sun6i-a31" "allwinner,sun8i-a23" "arm,psci" + "arm,realview-smp" + "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" @@ -201,6 +203,7 @@ nodes to be present and contain the properties described below. "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" + "rockchip,rk3036-smp" "rockchip,rk3066-smp" "ste,dbx500-smp" diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 34c88b0c7ab4..752a685d926f 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -131,6 +131,10 @@ Example: Freescale ARMv8 based Layerscape SoC family Device Tree Bindings ---------------------------------------------------------------- +LS1043A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; + LS2080A ARMv8 based Simulator model Required root node properties: - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 6ac7c000af22..e3ccab114006 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -187,6 +187,22 @@ Example: reg = <0xb0000000 0x10000>; }; +Hisilicon HiP05 PERISUB system controller + +Required properties: +- compatible : "hisilicon,hip05-perisubc", "syscon"; +- reg : Register address and size + +The HiP05 PERISUB system controller is shared by peripheral controllers in +HiP05 Soc to implement some basic configurations. The peripheral +controllers include mdio, ddr, iic, uart, timer and so on. + +Example: + /* for HiP05 perisub-ctrl-c system */ + peri_c_subctrl: syscon@80000000 { + compatible = "hisilicon,hip05-perisubc", "syscon"; + reg = <0x0 0x80000000 0x0 0x10000>; + }; ----------------------------------------------------------------------- Hisilicon CPU controller diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt index 5171ad8f48ff..ab0c9cdf388e 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -24,6 +24,8 @@ board. Currently known boards are: "buffalo,lswxl" "buffalo,lsxhl" "buffalo,lsxl" +"cloudengines,pogo02" +"cloudengines,pogoplugv4" "dlink,dns-320" "dlink,dns-320-a1" "dlink,dns-325" diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 618a91994a18..54f43bc2df44 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -6,6 +6,7 @@ following property: Required root node property: compatible: Must contain one of + "mediatek,mt2701" "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" @@ -17,6 +18,9 @@ compatible: Must contain one of Supported boards: +- Evaluation board for MT2701: + Required root node properties: + - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; - Evaluation board for MT6580: Required root node properties: - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index f6cd3e4192ff..aaf8d1460c4d 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -18,7 +18,7 @@ The available clocks are defined in dt-bindings/clock/mt*-clk.h. Also it uses the common reset controller binding from Documentation/devicetree/bindings/reset/reset.txt. The available reset outputs are defined in -dt-bindings/reset-controller/mt*-resets.h +dt-bindings/reset/mt*-resets.h Example: diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index f25b85499a6f..2f6ff86df49f 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -18,7 +18,7 @@ The available clocks are defined in dt-bindings/clock/mt*-clk.h. Also it uses the common reset controller binding from Documentation/devicetree/bindings/reset/reset.txt. The available reset outputs are defined in -dt-bindings/reset-controller/mt*-resets.h +dt-bindings/reset/mt*-resets.h Example: diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 9f4e5136e568..a2bd593881ca 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -138,9 +138,21 @@ Boards: - AM335X phyBOARD-WEGA: Single Board Computer dev kit compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4 + compatible = "compulab,cm-t335", "ti,am33xx" + +- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4 + compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" +- AM437x CM-T43 + compatible = "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + +- AM437x SBC-T43 + compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" + - AM43x EPOS EVM compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" @@ -150,6 +162,12 @@ Boards: - AM437x SK EVM: AM437x StarterKit Evaluation Module compatible = "ti,am437x-sk-evm", "ti,am4372", "ti,am43" +- AM57XX CL-SOM-AM57x + compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM57XX SBC-AM57x + compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 8e985dd2f181..078c14fcdaaa 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -1,6 +1,10 @@ Rockchip platforms device tree bindings --------------------------------------- +- Kylin RK3036 board: + Required root node properties: + - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036"; + - MarsBoard RK3066 board: Required root node properties: - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a"; @@ -35,6 +39,11 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- Google Brain (dev-board): + Required root node properties: + - compatible = "google,veyron-brain-rev0", "google,veyron-brain", + "google,veyron", "rockchip,rk3288"; + - Google Jaq (Haier Chromebook 11 and more): Required root node properties: - compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", @@ -49,6 +58,15 @@ Rockchip platforms device tree bindings "google,veyron-jerry-rev3", "google,veyron-jerry", "google,veyron", "rockchip,rk3288"; +- Google Mickey (Asus Chromebit CS10): + Required root node properties: + - compatible = "google,veyron-mickey-rev8", "google,veyron-mickey-rev7", + "google,veyron-mickey-rev6", "google,veyron-mickey-rev5", + "google,veyron-mickey-rev4", "google,veyron-mickey-rev3", + "google,veyron-mickey-rev2", "google,veyron-mickey-rev1", + "google,veyron-mickey-rev0", "google,veyron-mickey", + "google,veyron", "rockchip,rk3288"; + - Google Minnie (Asus Chromebook Flip C100P): Required root node properties: - compatible = "google,veyron-minnie-rev4", "google,veyron-minnie-rev3", @@ -69,6 +87,14 @@ Rockchip platforms device tree bindings "google,veyron-speedy-rev3", "google,veyron-speedy-rev2", "google,veyron-speedy", "google,veyron", "rockchip,rk3288"; +- Rockchip RK3368 evb: + Required root node properties: + - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368"; + - Rockchip R88 board: Required root node properties: - compatible = "rockchip,r88", "rockchip,rk3368"; + +- Rockchip RK3228 Evaluation board: + Required root node properties: + - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index f46ca9a316a2..ccaaec6014bd 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -47,6 +47,9 @@ Required properties: - samsung,syscon-phandle Contains the PMU system controller node (To access the ADC_PHY register on Exynos5250/5420/5800/3250) +Optional properties: +- has-touchscreen: If present, indicates that a touchscreen is + connected an usable. Note: child nodes can be added for auto probing from device tree. diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt index c447680519bb..08a587875996 100644 --- a/Documentation/devicetree/bindings/arm/scu.txt +++ b/Documentation/devicetree/bindings/arm/scu.txt @@ -10,10 +10,13 @@ References: Revision r2p0 - Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual Revision r0p1 +- ARM11 MPCore: see DDI0360F ARM 11 MPCore Processor Technical Reference + Manial Revision r2p0 - compatible : Should be: "arm,cortex-a9-scu" "arm,cortex-a5-scu" + "arm,arm11mp-scu" - reg : Specify the base address and the size of the SCU register window. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 40bb9007cd0d..9cf67e48f222 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -27,6 +27,8 @@ SoCs: compatible = "renesas,r8a7793" - R-Car E2 (R8A77940) compatible = "renesas,r8a7794" + - R-Car H3 (R8A77950) + compatible = "renesas,r8a7795" Boards: @@ -57,5 +59,7 @@ Boards: compatible = "renesas,marzen", "renesas,r8a7779" - Porter (M2-LCDP) compatible = "renesas,porter", "renesas,r8a7791" + - Salvator-X (RTP0RC7795SIPB0010S) + compatible = "renesas,salvator-x", "renesas,r8a7795"; - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" diff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt new file mode 100644 index 000000000000..842298894cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/technologic.txt @@ -0,0 +1,6 @@ +Technologic Systems Platforms Device Tree Bindings +-------------------------------------------------- + +TS-4800 board +Required root node properties: + - compatible = "technologic,imx51-ts4800", "fsl,imx51"; diff --git a/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt new file mode 100644 index 000000000000..68ef80afff16 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt @@ -0,0 +1,66 @@ +UniPhier System Bus + +The UniPhier System Bus is an external bus that connects on-board devices to +the UniPhier SoC. It is a simple (semi-)parallel bus with address, data, and +some control signals. It supports up to 8 banks (chip selects). + +Before any access to the bus, the bus controller must be configured; the bus +controller registers provide the control for the translation from the offset +within each bank to the CPU-viewed address. The needed setup includes the base +address, the size of each bank. Optionally, some timing parameters can be +optimized for faster bus access. + +Required properties: +- compatible: should be "socionext,uniphier-system-bus". +- reg: offset and length of the register set for the bus controller device. +- #address-cells: should be 2. The first cell is the bank number (chip select). + The second cell is the address offset within the bank. +- #size-cells: should be 1. +- ranges: should provide a proper address translation from the System Bus to + the parent bus. + +Note: +The address region(s) that can be assigned for the System Bus is implementation +defined. Some SoCs can use 0x00000000-0x0fffffff and 0x40000000-0x4fffffff, +while other SoCs can only use 0x40000000-0x4fffffff. There might be additional +limitations depending on SoCs and the boot mode. The address translation is +arbitrary as long as the banks are assigned in the supported address space with +the required alignment and they do not overlap one another. +For example, it is possible to map: + bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff +It is also possible to map: + bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff +There is no reason to stick to a particular translation mapping, but the +"ranges" property should provide a "reasonable" default that is known to work. +The software should initialize the bus controller according to it. + +Example: + + system-bus { + compatible = "socionext,uniphier-system-bus"; + reg = <0x58c00000 0x400>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <1 0x00000000 0x42000000 0x02000000 + 5 0x00000000 0x46000000 0x01000000>; + + ethernet@1,01f00000 { + compatible = "smsc,lan9115"; + reg = <1 0x01f00000 0x1000>; + interrupts = <0 48 4> + phy-mode = "mii"; + }; + + uart@5,00200000 { + compatible = "ns16550a"; + reg = <5 0x00200000 0x20>; + interrupts = <0 49 4> + clock-frequency = <12288000>; + }; + }; + +In this example, + - the Ethernet device is connected at the offset 0x01f00000 of CS1 and + mapped to 0x43f00000 of the parent bus. + - the UART device is connected at the offset 0x00200000 of CS5 and + mapped to 0x46200000 of the parent bus. diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt new file mode 100644 index 000000000000..8b7177cecb36 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -0,0 +1,40 @@ +ARM System Controller ICST clocks + +The ICS525 and ICS307 oscillators are produced by Integrated Devices +Technology (IDT). ARM integrated these oscillators deeply into their +reference designs by adding special control registers that manage such +oscillators to their system controllers. + +The ARM system controller contains logic to serialize and initialize +an ICST clock request after a write to the 32 bit register at an offset +into the system controller. Furthermore, to even be able to alter one of +these frequencies, the system controller must first be unlocked by +writing a special token to another offset in the system controller. + +The ICST oscillator must be provided inside a system controller node. + +Required properties: +- lock-offset: the offset address into the system controller where the + unlocking register is located +- vco-offset: the offset address into the system controller where the + ICST control register is located (even 32 bit address) +- compatible: must be one of "arm,syscon-icst525" or "arm,syscon-icst307" +- #clock-cells: must be <0> +- clocks: parent clock, since the ICST needs a parent clock to derive its + frequency from, this attribute is compulsory. + +Example: + +syscon: syscon@10000000 { + compatible = "syscon"; + reg = <0x10000000 0x1000>; + + oscclk0: osc0@0c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x0c>; + clocks = <&xtal24mhz>; + }; + (...) +}; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt new file mode 100644 index 000000000000..7a837d2182ac --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt @@ -0,0 +1,31 @@ +Broadcom BCM2835 auxiliary peripheral support + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +The auxiliary peripherals (UART, SPI1, and SPI2) have a small register +area controlling clock gating to the peripherals, and providing an IRQ +status register. + +Required properties: +- compatible: Should be "brcm,bcm2835-aux" +- #clock-cells: Should be <1>. The permitted clock-specifier values can be + found in include/dt-bindings/clock/bcm2835-aux.h +- reg: Specifies base physical address and size of the registers +- clocks: The parent clock phandle + +Example: + + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + clocks = <&clk_osc>; + }; + + aux: aux@0x7e215004 { + compatible = "brcm,bcm2835-aux"; + #clock-cells = <1>; + reg = <0x7e215000 0x8>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index ede65a55e21b..0b35e71b39e8 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -208,3 +208,8 @@ These clock IDs are defined in: ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED + +BCM63138 +-------- +PLL and leaf clock compatible strings for BCM63138 are: + "brcm,bcm63138-armpll" diff --git a/Documentation/devicetree/bindings/clock/cs2000-cp.txt b/Documentation/devicetree/bindings/clock/cs2000-cp.txt new file mode 100644 index 000000000000..54e6df0bee8a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/cs2000-cp.txt @@ -0,0 +1,22 @@ +CIRRUS LOGIC Fractional-N Clock Synthesizer & Clock Multiplier + +Required properties: + +- compatible: "cirrus,cs2000-cp" +- reg: The chip select number on the I2C bus +- clocks: common clock binding for CLK_IN, XTI/REF_CLK +- clock-names: CLK_IN : clk_in, XTI/REF_CLK : ref_clk +- #clock-cells: must be <0> + +Example: + +&i2c2 { + ... + cs2000: clk_multiplier@4f { + #clock-cells = <0>; + compatible = "cirrus,cs2000-cp"; + reg = <0x4f>; + clocks = <&rcar_sound 0>, <&x12_clk>; + clock-names = "clk_in", "ref_clk"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/dove-divider-clock.txt b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt new file mode 100644 index 000000000000..e3eb0f657c5e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt @@ -0,0 +1,28 @@ +PLL divider based Dove clocks + +Marvell Dove has a 2GHz PLL, which feeds into a set of dividers to provide +high speed clocks for a number of peripherals. These dividers are part of +the PMU, and thus this node should be a child of the PMU node. + +The following clocks are provided: + +ID Clock +------------- +0 AXI bus clock +1 GPU clock +2 VMeta clock +3 LCD clock + +Required properties: +- compatible : shall be "marvell,dove-divider-clock" +- reg : shall be the register address of the Core PLL and Clock Divider + Control 0 register. This will cover that register, as well as the + Core PLL and Clock Divider Control 1 register. Thus, it will have + a size of 8. +- #clock-cells : from common clock binding; shall be set to 1 + +divider_clk: core-clock@0064 { + compatible = "marvell,dove-divider-clock"; + reg = <0x0064 0x8>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt new file mode 100644 index 000000000000..26f237f641b7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt @@ -0,0 +1,56 @@ +NVIDIA Tegra210 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra210-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra210-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra210-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA210_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt b/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt new file mode 100644 index 000000000000..20cbca3f41d8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt @@ -0,0 +1,30 @@ +NXP LPC32xx Clock Controller + +Required properties: +- compatible: should be "nxp,lpc3220-clk" +- reg: should contain clock controller registers location and length +- #clock-cells: must be 1, the cell holds id of a clock provided by the + clock controller +- clocks: phandles of external oscillators, the list must contain one + 32768 Hz oscillator and may have one optional high frequency oscillator +- clock-names: list of external oscillator clock names, must contain + "xtal_32k" and may have optional "xtal" + +Examples: + + /* System Control Block */ + scb { + compatible = "simple-bus"; + ranges = <0x0 0x040004000 0x00001000>; + #address-cells = <1>; + #size-cells = <1>; + + clk: clock-controller@0 { + compatible = "nxp,lpc3220-clk"; + reg = <0x00 0x114>; + #clock-cells = <1>; + + clocks = <&xtal_32k>, <&xtal>; + clock-names = "xtal_32k", "xtal"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt b/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt new file mode 100644 index 000000000000..0aa249409b51 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt @@ -0,0 +1,22 @@ +NXP LPC32xx USB Clock Controller + +Required properties: +- compatible: should be "nxp,lpc3220-usb-clk" +- reg: should contain clock controller registers location and length +- #clock-cells: must be 1, the cell holds id of a clock provided by the + USB clock controller + +Examples: + + usb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x0 0x31020000 0x00001000>; + + usbclk: clock-controller@f00 { + compatible = "nxp,lpc3220-usb-clk"; + reg = <0xf00 0x100>; + #clock-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 152dfaab2575..72f82f444091 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -13,6 +13,7 @@ Required properties : "qcom,gcc-msm8974" "qcom,gcc-msm8974pro" "qcom,gcc-msm8974pro-ac" + "qcom,gcc-msm8996" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index 34e7614d5074..8b0f7841af8d 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -9,6 +9,7 @@ Required properties : "qcom,mmcc-msm8660" "qcom,mmcc-msm8960" "qcom,mmcc-msm8974" + "qcom,mmcc-msm8996" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt index 38dcf0370143..ae36ab842919 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt @@ -20,6 +20,10 @@ Required Properties: clocks must be specified. For clocks with multiple parents, invalid settings must be specified as "<0>". - #clock-cells: Must be 0 + + +Optional Properties: + - clock-output-names: The name of the clock as a free-form string diff --git a/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt b/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt index 36c2b528245c..399e0da22348 100644 --- a/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt +++ b/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt @@ -2,7 +2,7 @@ Required Properties: - - compatible: Must be "renesas,sh73a0-h8300-div-clock" + - compatible: Must be "renesas,h8300-div-clock" - clocks: Reference to the parent clocks ("extal1" and "extal2") diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt new file mode 100644 index 000000000000..ace05992a262 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt @@ -0,0 +1,56 @@ +* Rockchip RK3036 Clock and Reset Unit + +The RK3036 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3036-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3036-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3036-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@20060000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20060000 0x100>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt new file mode 100644 index 000000000000..f323048127eb --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt @@ -0,0 +1,58 @@ +* Rockchip RK3228 Clock and Reset Unit + +The RK3228 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3228-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3228-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + - "ext_hsadc" - external HSADC clock - optional + - "phy_50m_out" - output clock of the pll in the mac phy + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3228-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10110000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10110000 0x100>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 8a47b77abfca..e59f57b24777 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -27,7 +27,9 @@ Required properties: "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 + "allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80 "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31 + "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80 @@ -55,6 +57,9 @@ Required properties: "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 + "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3 + "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80 + "allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10 "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 "allwinner,sun4i-a10-mmc-clk" - for the MMC clock "allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80 @@ -68,8 +73,10 @@ Required properties: "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 "allwinner,sun8i-a23-usb-clk" - for usb gates + resets on A23 + "allwinner,sun8i-h3-usb-clk" - for usb gates + resets on H3 "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 + "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock Required properties for all clocks: - reg : shall be the control register address for the clock. @@ -89,6 +96,9 @@ Required properties for all clocks: And "allwinner,*-usb-clk" clocks also require: - reset-cells : shall be set to 1 +The "allwinner,sun4i-a10-ve-clk" clock also requires: +- reset-cells : shall be set to 0 + The "allwinner,sun9i-a80-mmc-config-clk" clock also requires: - #reset-cells : shall be set to 1 - resets : shall be the reset control phandle for the mmc block. diff --git a/Documentation/devicetree/bindings/clock/tango4-clock.txt b/Documentation/devicetree/bindings/clock/tango4-clock.txt new file mode 100644 index 000000000000..19c580a7bda2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/tango4-clock.txt @@ -0,0 +1,23 @@ +* Sigma Designs Tango4 Clock Generator + +The Tango4 clock generator outputs cpu_clk and sys_clk (the latter is used +for RAM and various peripheral devices). The clock binding described here +is applicable to all Tango4 SoCs. + +Required Properties: + +- compatible: should be "sigma,tango4-clkgen". +- reg: physical base address of the device and length of memory mapped region. +- clocks: phandle of the input clock (crystal oscillator). +- clock-output-names: should be "cpuclk" and "sysclk". +- #clock-cells: should be set to 1. + +Example: + + clkgen: clkgen@10000 { + compatible = "sigma,tango4-clkgen"; + reg = <0x10000 0x40>; + clocks = <&xtal>; + clock-output-names = "cpuclk", "sysclk"; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt index 0715695e94a9..2aa06ac0fac5 100644 --- a/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt +++ b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt @@ -12,7 +12,7 @@ must be present contiguously. Generic DT driver will check only node 'x' for cpu:x. Required properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt +- operating-points: Refer to Documentation/devicetree/bindings/opp/opp.txt for details Optional properties: diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt index e41c98ffbccb..dd3929e85dec 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt @@ -11,7 +11,7 @@ Required properties: - None Optional properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt for +- operating-points: Refer to Documentation/devicetree/bindings/opp/opp.txt for details. OPPs *must* be supplied either via DT, i.e. this property, or populated at runtime. - clock-latency: Specify the possible maximum transition latency for clock, diff --git a/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt b/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt new file mode 100644 index 000000000000..ed5e0a7894ad --- /dev/null +++ b/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt @@ -0,0 +1,54 @@ +Etnaviv DRM master device +========================= + +The Etnaviv DRM master device is a virtual device needed to list all +Vivante GPU cores that comprise the GPU subsystem. + +Required properties: +- compatible: Should be one of + "fsl,imx-gpu-subsystem" + "marvell,dove-gpu-subsystem" +- cores: Should contain a list of phandles pointing to Vivante GPU devices + +example: + +gpu-subsystem { + compatible = "fsl,imx-gpu-subsystem"; + cores = <&gpu_2d>, <&gpu_3d>; +}; + + +Vivante GPU core devices +======================== + +Required properties: +- compatible: Should be "vivante,gc" + A more specific compatible is not needed, as the cores contain chip + identification registers at fixed locations, which provide all the + necessary information to the driver. +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain the cores interrupt line +- clocks: should contain one clock for entry in clock-names + see Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: + - "bus": AXI/register clock + - "core": GPU core clock + - "shader": Shader clock (only required if GPU has feature PIPE_3D) + +Optional properties: +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt + +example: + +gpu_3d: gpu@00130000 { + compatible = "vivante,gc"; + reg = <0x00130000 0x4000>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_GPU3D_AXI>, + <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>; + clock-names = "bus", "core", "shader"; + power-domains = <&gpc 1>; +}; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index 64693f2ebc51..fe4a7a2dea9c 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -1,3 +1,20 @@ +Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP) + +DisplayPort is industry standard to accommodate the growing board adoption +of digital display technology within the PC and CE industries. +It consolidates the internal and external connection methods to reduce device +complexity and cost. It also supports necessary features for important cross +industry applications and provides performance scalability to enable the next +generation of displays that feature higher color depths, refresh rates, and +display resolutions. + +eDP (embedded display port) device is compliant with Embedded DisplayPort +standard as follows, +- DisplayPort standard 1.1a for Exynos5250 and Exynos5260. +- DisplayPort standard 1.3 for Exynos5422s and Exynos5800. + +eDP resides between FIMD and panel or FIMD and bridge such as LVDS. + The Exynos display port interface should be configured based on the type of panel connected to it. @@ -66,8 +83,15 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection - -video interfaces: Device node can contain video interface port - nodes according to [1]. +Video interfaces: + Device node can contain video interface port nodes according to [1]. + The following are properties specific to those nodes: + + endpoint node connected to bridge or panel node: + - remote-endpoint: specifies the endpoint in panel or bridge node. + This node is required in all kinds of exynos dp + to represent the connection between dp and bridge + or dp and panel. [1]: Documentation/devicetree/bindings/media/video-interfaces.txt @@ -111,9 +135,18 @@ Board Specific portion: }; ports { - port@0 { + port { dp_out: endpoint { - remote-endpoint = <&bridge_in>; + remote-endpoint = <&dp_in>; + }; + }; + }; + + panel { + ... + port { + dp_in: endpoint { + remote-endpoint = <&dp_out>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index 1fd8cf9cbfac..d474f59be6d6 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -2,10 +2,9 @@ Device-Tree bindings for drm hdmi driver Required properties: - compatible: value should be one among the following: - 1) "samsung,exynos5-hdmi" <DEPRECATED> - 2) "samsung,exynos4210-hdmi" - 3) "samsung,exynos4212-hdmi" - 4) "samsung,exynos5420-hdmi" + 1) "samsung,exynos4210-hdmi" + 2) "samsung,exynos4212-hdmi" + 3) "samsung,exynos5420-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index f344b9e49198..e7423bea1424 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -14,17 +14,20 @@ Required properties: - clocks: device clocks See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. - clock-names: the following clocks are required: + * "mdp_core_clk" + * "iface_clk" * "bus_clk" - * "byte_clk" - * "core_clk" * "core_mmss_clk" - * "iface_clk" - * "mdp_core_clk" + * "byte_clk" * "pixel_clk" + * "core_clk" + For DSIv2, we need an additional clock: + * "src_clk" - vdd-supply: phandle to vdd regulator device node - vddio-supply: phandle to vdd-io regulator device node - vdda-supply: phandle to vdda regulator device node - qcom,dsi-phy: phandle to DSI PHY device node +- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) Optional properties: - panel@0: Node of panel connected to this DSI controller. @@ -51,6 +54,7 @@ Required properties: * "qcom,dsi-phy-28nm-hpm" * "qcom,dsi-phy-28nm-lp" * "qcom,dsi-phy-20nm" + * "qcom,dsi-phy-28nm-8960" - reg: Physical base address and length of the registers of PLL, PHY and PHY regulator - reg-names: The names of register regions. The following regions are required: diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt index 0833edaba4c3..a214f6cd0363 100644 --- a/Documentation/devicetree/bindings/display/msm/mdp.txt +++ b/Documentation/devicetree/bindings/display/msm/mdp.txt @@ -2,18 +2,28 @@ Qualcomm adreno/snapdragon display controller Required properties: - compatible: - * "qcom,mdp" - mdp4 + * "qcom,mdp4" - mdp4 + * "qcom,mdp5" - mdp5 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt signal from the display controller. - connectors: array of phandles for output device(s) - clocks: device clocks See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "src_clk" - * "hdmi_clk" - * "mpd_clk" +- clock-names: the following clocks are required. + For MDP4: + * "core_clk" + * "iface_clk" + * "lut_clk" + * "src_clk" + * "hdmi_clk" + * "mdp_clk" + For MDP5: + * "bus_clk" + * "iface_clk" + * "core_clk_src" + * "core_clk" + * "lut_clk" (some MDP5 versions may not need this) + * "vsync_clk" Optional properties: - gpus: phandle for gpu device @@ -26,7 +36,7 @@ Example: ... mdp: qcom,mdp@5100000 { - compatible = "qcom,mdp"; + compatible = "qcom,mdp4"; reg = <0x05100000 0xf0000>; interrupts = <GIC_SPI 75 0>; connectors = <&hdmi>; diff --git a/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt b/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt new file mode 100644 index 000000000000..50be5e2438b2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt @@ -0,0 +1,7 @@ +Boe Corporation 8.0" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "boe,tv080wum-nl0" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt b/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt new file mode 100644 index 000000000000..649744620ae1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt @@ -0,0 +1,7 @@ +Innolux Corporation 12.1" G121X1-L03 XGA (1024x768) TFT LCD panel + +Required properties: +- compatible: should be "innolux,g121x1-l03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt b/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt new file mode 100644 index 000000000000..a8e940fe731e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt @@ -0,0 +1,7 @@ +Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel + +Required properties: +- compatible: should be "kyo,tcg121xglp" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt new file mode 100644 index 000000000000..37dedf6a6702 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt @@ -0,0 +1,20 @@ +Panasonic 10" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "panasonic,vvx10f034n00" +- reg: DSI virtual channel of the peripheral +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel + +Example: + + mdss_dsi@fd922800 { + panel@0 { + compatible = "panasonic,vvx10f034n00"; + reg = <0>; + power-supply = <&vreg_vsp>; + backlight = <&lp8566_wled>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt b/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt new file mode 100644 index 000000000000..0fbdab89ac3d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt @@ -0,0 +1,7 @@ +QiaoDian XianShi Corporation 4"3 TFT LCD panel + +Required properties: +- compatible: should be "qiaodian,qd43003c0-40" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt new file mode 100644 index 000000000000..3770a111968b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt @@ -0,0 +1,22 @@ +Sharp Microelectronics 4.3" qHD TFT LCD panel + +Required properties: +- compatible: should be "sharp,ls043t1le01-qhd" +- reg: DSI virtual channel of the peripheral +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- reset-gpios: a GPIO spec for the reset pin + +Example: + + mdss_dsi@fd922800 { + panel@0 { + compatible = "sharp,ls043t1le01-qhd"; + reg = <0>; + avdd-supply = <&pm8941_l22>; + backlight = <&pm8941_wled>; + reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt new file mode 100644 index 000000000000..70cd8d18d841 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt @@ -0,0 +1,4 @@ +Startek Electronic Technology Co. KD050C 5.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "startek,startek-kd050c" diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt new file mode 100644 index 000000000000..1753f0cc6fad --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -0,0 +1,60 @@ +Rockchip specific extensions to the Synopsys Designware MIPI DSI +================================ + +Required properties: +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. +- compatible: "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi". +- reg: Represent the physical address range of the controller. +- interrupts: Represent the controller's interrupt to the CPU(s). +- clocks, clock-names: Phandles to the controller's pll reference + clock(ref) and APB clock(pclk), as described in [1]. +- rockchip,grf: this soc should set GRF regs to mux vopl/vopb. +- ports: contain a port node with endpoint definitions as defined in [2]. + For vopb,set the reg = <0> and set the reg = <1> for vopl. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + mipi_dsi: mipi@ff960000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi"; + reg = <0xff960000 0x4000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>; + clock-names = "ref", "pclk"; + rockchip,grf = <&grf>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + mipi_in: port { + #address-cells = <1>; + #size-cells = <0>; + mipi_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_mipi>; + }; + mipi_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_mipi>; + }; + }; + }; + + panel { + compatible ="boe,tv080wum-nl0"; + reg = <0>; + + enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_en>; + backlight = <&backlight>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index d15351f2313d..5489b59e3d41 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -7,6 +7,7 @@ buffer to an external LCD interface. Required properties: - compatible: value should be one of the following "rockchip,rk3288-vop"; + "rockchip,rk3036-vop"; - interrupts: should contain a list of all VOP IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer.txt b/Documentation/devicetree/bindings/display/simple-framebuffer.txt index 4474ef6e0b95..8c9e9f515c87 100644 --- a/Documentation/devicetree/bindings/display/simple-framebuffer.txt +++ b/Documentation/devicetree/bindings/display/simple-framebuffer.txt @@ -47,10 +47,14 @@ Required properties: - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r). Optional properties: -- clocks : List of clocks used by the framebuffer. Clocks listed here - are expected to already be configured correctly. The OS must - ensure these clocks are not modified or disabled while the - simple framebuffer remains active. +- clocks : List of clocks used by the framebuffer. +- *-supply : Any number of regulators used by the framebuffer. These should + be named according to the names in the device's design. + + The above resources are expected to already be configured correctly. + The OS must ensure they are not modified or disabled while the simple + framebuffer remains active. + - display : phandle pointing to the primary display hardware node Example: @@ -68,6 +72,7 @@ chosen { stride = <(1600 * 2)>; format = "r5g6b5"; clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>; + lcd-supply = <®_dc1sw>; display = <&lcdc0>; }; stdout-path = "display0"; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 09daeef1ff22..5b902ac8d97e 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -14,7 +14,14 @@ not described in these device tree bindings. Required Properties: -- compatible: must contain "renesas,rcar-dmac" +- compatible: "renesas,dmac-<soctype>", "renesas,rcar-dmac" as fallback. + Examples with soctypes are: + - "renesas,dmac-r8a7790" (R-Car H2) + - "renesas,dmac-r8a7791" (R-Car M2-W) + - "renesas,dmac-r8a7792" (R-Car V2H) + - "renesas,dmac-r8a7793" (R-Car M2-N) + - "renesas,dmac-r8a7794" (R-Car E2) + - "renesas,dmac-r8a7795" (R-Car H3) - reg: base address and length of the registers block for the DMAC @@ -35,7 +42,7 @@ Required Properties: Example: R8A7790 (R-Car H2) SYS-DMACs dmac0: dma-controller@e6700000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xe6700000 0 0x20000>; interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH 0 200 IRQ_TYPE_LEVEL_HIGH @@ -65,7 +72,7 @@ Example: R8A7790 (R-Car H2) SYS-DMACs }; dmac1: dma-controller@e6720000 { - compatible = "renesas,rcar-dmac"; + compatible = "renesas,dmac-r8a7790", "renesas,rcar-dmac"; reg = <0 0xe6720000 0 0x20000>; interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH 0 216 IRQ_TYPE_LEVEL_HIGH diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 13df9933f4cd..6b4a98f74be3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -25,6 +25,7 @@ Required properties: ti,tca6416 ti,tca6424 ti,tca9539 + onsemi,pca9654 exar,xra1202 Example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt index ba2bb84eeac3..c809acb9c71b 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt @@ -5,7 +5,8 @@ Required properties: - compatible: should be "semtech,sx1506q", "semtech,sx1508q", - "semtech,sx1509q". + "semtech,sx1509q", + "semtech,sx1502q". - reg: The I2C slave address for this device. diff --git a/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt b/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt new file mode 100644 index 000000000000..ba051074bedc --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt @@ -0,0 +1,16 @@ +* TPS65086 GPO Controller bindings + +Required properties: + - compatible : Should be "ti,tps65086-gpio". + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number + and the second cell is used to specify flags. + See ../gpio/gpio.txt for possible values. + +Example: + + gpio4: gpio { + compatible = "ti,tps65086-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index cf1333d1dd52..21641236c095 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -6,6 +6,7 @@ Required properties: Optional properties: - autorepeat: Boolean, Enable auto repeat feature of Linux input subsystem. + - label: String, name of the input device. Each button (key) is represented as a sub-node of "gpio-keys": Subnode properties: diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index afef6a85ac51..b8e1674c7837 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -14,6 +14,7 @@ Required properties: "mediatek,mt6582-sysirq" "mediatek,mt6580-sysirq" "mediatek,mt6577-sysirq" + "mediatek,mt2701-sysirq" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Use the same format as specified by GIC in Documentation/devicetree/bindings/arm/gic.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt new file mode 100644 index 000000000000..c3a1b37c4c35 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt @@ -0,0 +1,67 @@ +Microchip PIC32 Interrupt Controller +==================================== + +The Microchip PIC32 contains an Enhanced Vectored Interrupt Controller (EVIC). +It handles all internal and external interrupts. This controller exists outside +of the CPU and is the arbitrator of all interrupts (including interrupts from +the CPU itself) before they are presented to the CPU. + +External interrupts have a software configurable edge polarity. Non external +interrupts have a type and polarity that is determined by the source of the +interrupt. + +Required properties +------------------- + +- compatible: Should be "microchip,pic32mzda-evic" +- reg: Specifies physical base address and size of register range. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt cells: Specifies the number of cells used to encode an interrupt + source connected to this controller. The value shall be 2 and interrupt + descriptor shall have the following format: + + <hw_irq irq_type> + + hw_irq - represents the hardware interrupt number as in the data sheet. + irq_type - is used to describe the type and polarity of an interrupt. For + internal interrupts use IRQ_TYPE_EDGE_RISING for non persistent interrupts and + IRQ_TYPE_LEVEL_HIGH for persistent interrupts. For external interrupts use + IRQ_TYPE_EDGE_RISING or IRQ_TYPE_EDGE_FALLING to select the desired polarity. + +Optional properties +------------------- +- microchip,external-irqs: u32 array of external interrupts with software + polarity configuration. This array corresponds to the bits in the INTCON + SFR. + +Example +------- + +evic: interrupt-controller@1f810000 { + compatible = "microchip,pic32mzda-evic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1f810000 0x1000>; + microchip,external-irqs = <3 8 13 18 23>; +}; + +Each device/peripheral must request its interrupt line with the associated type +and polarity. + +Internal interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <113 IRQ_TYPE_LEVEL_HIGH>; + ... +}; + +External interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + ... +}; diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index cd29083e16ec..48ffb38f699e 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -7,7 +7,15 @@ connected to the IPMMU through a port called micro-TLB. Required Properties: - - compatible: Must contain "renesas,ipmmu-vmsa". + - compatible: Must contain SoC-specific and generic entries from below. + + - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. + - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. + - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. + - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. + - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. + - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. + - reg: Base address and size of the IPMMU registers. - interrupts: Specifiers for the MMU fault interrupts. For instances that support secure mode two interrupts must be specified, for non-secure and @@ -27,7 +35,7 @@ node with the following property: Example: R8A7791 IPMMU-MX and VSP1-D0 bus master ipmmu_mx: mmu@fe951000 { - compatible = "renasas,ipmmu-vmsa"; + compatible = "renasas,ipmmu-r8a7791", "renasas,ipmmu-vmsa"; reg = <0 0xfe951000 0 0x1000>; interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 0604d42f38d1..5fe9372abb37 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -7,6 +7,10 @@ Required properties: - reg: should contain G-Scaler physical address location and length. - interrupts: should contain G-Scaler interrupt number +Optional properties: +- samsung,sysreg: handle to syscon used to control the system registers to + set writeback input and destination + Example: gsc_0: gsc@0x13e00000 { diff --git a/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt new file mode 100644 index 000000000000..1c8dbc45feec --- /dev/null +++ b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt @@ -0,0 +1,31 @@ +* Microchip PIC32MZDA Platforms + +PIC32MZDA Starter Kit +Required root node properties: + - compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda" + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required. Required properties: + - device_type: Must be "cpu". + - compatible: Must be "mti,mips14KEc". +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,mips14KEc"; + }; + }; + +Boot protocol +-------------- +In accordance with Unified Hosting Interface Reference Manual (MD01069), the +bootloader must pass the following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt new file mode 100644 index 000000000000..aa6313024176 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt @@ -0,0 +1,26 @@ +Mediatek Gigabit Switch +======================= + +The mediatek gigabit switch can be found on Mediatek SoCs (mt7620, mt7621). + +Required properties: +- compatible: Should be "mediatek,mt7620-gsw" or "mediatek,mt7621-gsw" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the gigabit switches interrupt +- resets: Should contain the gigabit switches resets +- reset-names: Should contain the reset names "gsw" + +Example: + +gsw@10110000 { + compatible = "ralink,mt7620-gsw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "gsw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt new file mode 100644 index 000000000000..88b095d1f13b --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt @@ -0,0 +1,61 @@ +Ralink Frame Engine Ethernet controller +======================================= + +The Ralink frame engine ethernet controller can be found on Ralink and +Mediatek SoCs (RT288x, RT3x5x, RT366x, RT388x, rt5350, mt7620, mt7621, mt76x8). + +Depending on the SoC, there is a number of ports connected to the CPU port +directly and/or via a (gigabit-)switch. + +* Ethernet controller node + +Required properties: +- compatible: Should be one of "ralink,rt2880-eth", "ralink,rt3050-eth", + "ralink,rt3050-eth", "ralink,rt3883-eth", "ralink,rt5350-eth", + "mediatek,mt7620-eth", "mediatek,mt7621-eth" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the frame engines interrupt +- resets: Should contain the frame engines resets +- reset-names: Should contain the reset names "fe". If a switch is present + "esw" is also required. + + +* Ethernet port node + +Required properties: +- compatible: Should be "ralink,eth-port" +- reg: The number of the physical port +- phy-handle: reference to the node describing the phy + +Example: + +mdio-bus { + ... + phy0: ethernet-phy@0 { + phy-mode = "mii"; + reg = <0>; + }; +}; + +ethernet@400000 { + compatible = "ralink,rt2880-eth"; + reg = <0x00400000 10000>; + + #address-cells = <1>; + #size-cells = <0>; + + resets = <&rstctrl 18>; + reset-names = "fe"; + + interrupt-parent = <&cpuintc>; + interrupts = <5>; + + port@0 { + compatible = "ralink,eth-port"; + reg = <0>; + phy-handle = <&phy0>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt new file mode 100644 index 000000000000..2e79bd376c56 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt @@ -0,0 +1,32 @@ +Ralink Fast Ethernet Embedded Switch +==================================== + +The ralink fast ethernet embedded switch can be found on Ralink and Mediatek +SoCs (RT3x5x, RT5350, MT76x8). + +Required properties: +- compatible: Should be "ralink,rt3050-esw" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the embedded switches interrupt +- resets: Should contain the embedded switches resets +- reset-names: Should contain the reset names "esw" + +Optional properties: +- ralink,portmap: can be used to choose if the default switch setup is + llllw or wllll +- ralink,led_polarity: override the active high/low settings of the leds + +Example: + +esw@10110000 { + compatible = "ralink,rt3050-esw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "esw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt index 45c2a8094a9f..01b88f4e0d5b 100644 --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -1,7 +1,10 @@ * Broadcom iProc PCIe controller with the platform bus interface Required properties: -- compatible: Must be "brcm,iproc-pcie" +- compatible: Must be "brcm,iproc-pcie" for PAXB, or "brcm,iproc-pcie-paxc" + for PAXC. PAXB-based root complex is used for external endpoint devices. + PAXC-based root complex is connected to emulated endpoint devices + internal to the ASIC - reg: base address and length of the PCIe controller I/O register space - #interrupt-cells: set to <1> - interrupt-map-mask and interrupt-map, standard PCI properties to define the @@ -32,6 +35,28 @@ Optional: - brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to increase the outbound window size +MSI support (optional): + +For older platforms without MSI integrated in the GIC, iProc PCIe core provides +an event queue based MSI support. The iProc MSI uses host memories to store +MSI posted writes in the event queues + +- msi-parent: Link to the device node of the MSI controller. On newer iProc +platforms, the MSI controller may be gicv2m or gicv3-its. On older iProc +platforms without MSI support in its interrupt controller, one may use the +event queue based MSI support integrated within the iProc PCIe core. + +When the iProc event queue based MSI is used, one needs to define the +following properties in the MSI device node: +- compatible: Must be "brcm,iproc-msi" +- msi-controller: claims itself as an MSI controller +- interrupt-parent: Link to its parent interrupt device +- interrupts: List of interrupt IDs from its parent interrupt device + +Optional properties: +- brcm,pcie-msi-inten: Needs to be present for some older iProc platforms that +require the interrupt enable registers to be set explicitly to enable MSI + Example: pcie0: pcie@18012000 { compatible = "brcm,iproc-pcie"; @@ -58,6 +83,19 @@ Example: brcm,pcie-ob-oarr-size; brcm,pcie-ob-axi-offset = <0x00000000>; brcm,pcie-ob-window-size = <256>; + + msi-parent = <&msi0>; + + /* iProc event queue based MSI */ + msi0: msi@18012000 { + compatible = "brcm,iproc-msi"; + msi-controller; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>, + <GIC_SPI 97 IRQ_TYPE_NONE>, + <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + }; }; pcie1: pcie@18013000 { diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index 17c6ed9c6059..b721beacfe4d 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -1,4 +1,4 @@ -HiSilicon PCIe host bridge DT description +HiSilicon Hip05 and Hip06 PCIe host bridge DT description HiSilicon PCIe host controller is based on Designware PCI core. It shares common functions with PCIe Designware core driver and inherits @@ -7,8 +7,8 @@ Documentation/devicetree/bindings/pci/designware-pci.txt. Additional properties are described here: -Required properties: -- compatible: Should contain "hisilicon,hip05-pcie". +Required properties +- compatible: Should contain "hisilicon,hip05-pcie" or "hisilicon,hip06-pcie". - reg: Should contain rc_dbi, config registers location and length. - reg-names: Must include the following entries: "rc_dbi": controller configuration registers; @@ -20,7 +20,7 @@ Optional properties: - status: Either "ok" or "disabled". - dma-coherent: Present if DMA operations are coherent. -Example: +Hip05 Example (note that Hip06 is the same except compatible): pcie@0xb0080000 { compatible = "hisilicon,hip05-pcie", "snps,dw-pcie"; reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 7fab84b33531..4e8b90e43dd8 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -8,7 +8,14 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; - "renesas,pci-r8a7794" for the R8A7794 SoC. + "renesas,pci-r8a7794" for the R8A7794 SoC; + "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device + + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: A list of physical regions to access the device: the first is the operational registers for the OHCI/EHCI controllers and the second is for the bridge configuration and control registers. @@ -24,10 +31,15 @@ Required properties: - interrupt-map-mask: standard property that helps to define the interrupt mapping. +Optional properties: +- dma-ranges: a single range for the inbound memory region. If not supplied, + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the + allowed combinations of address and size. + Example SoC configuration: pci0: pci@ee090000 { - compatible = "renesas,pci-r8a7790"; + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; clocks = <&mstp7_clks R8A7790_CLK_EHCI>; reg = <0x0 0xee090000 0x0 0xc00>, <0x0 0xee080000 0x0 0x1100>; @@ -38,6 +50,7 @@ Example SoC configuration: #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; interrupt-map-mask = <0xff00 0 0 0x7>; interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt new file mode 100644 index 000000000000..4059a6f89bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -0,0 +1,233 @@ +* Qualcomm PCI express root complex + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain + - "qcom,pcie-ipq8064" for ipq8064 + - "qcom,pcie-apq8064" for apq8064 + - "qcom,pcie-apq8084" for apq8084 + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Must include the following entries + - "parf" Qualcomm specific registers + - "dbi" Designware PCIe registers + - "elbi" External local bus interface registers + - "config" PCIe configuration space + +- device_type: + Usage: required + Value type: <string> + Definition: Should be "pci". As specified in designware-pcie.txt + +- #address-cells: + Usage: required + Value type: <u32> + Definition: Should be 3. As specified in designware-pcie.txt + +- #size-cells: + Usage: required + Value type: <u32> + Definition: Should be 2. As specified in designware-pcie.txt + +- ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: MSI interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "msi" + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: Should be 1. As specified in designware-pcie.txt + +- interrupt-map-mask: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- interrupt-map: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: List of phandle and clock specifier pairs as listed + in clock-names property + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries + - "iface" Configuration AHB clock + +- clock-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "core" Clocks the pcie hw block + - "phy" Clocks the pcie PHY block +- clock-names: + Usage: required for apq8084 + Value type: <stringlist> + Definition: Should contain the following entries + - "aux" Auxiliary (AUX) clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: List of phandle and reset specifier pairs as listed + in reset-names property + +- reset-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "axi" AXI reset + - "ahb" AHB reset + - "por" POR reset + - "pci" PCI reset + - "phy" PHY reset + +- reset-names: + Usage: required for apq8084 + Value type: <stringlist> + Definition: Should contain the following entries + - "core" Core reset + +- power-domains: + Usage: required for apq8084 + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pair to the + power domain which is responsible for collapsing + and restoring power to the peripheral + +- vdda-supply: + Usage: required + Value type: <phandle> + Definition: A phandle to the core analog power supply + +- vdda_phy-supply: + Usage: required for ipq/apq8064 + Value type: <phandle> + Definition: A phandle to the analog power supply for PHY + +- vdda_refclk-supply: + Usage: required for ipq/apq8064 + Value type: <phandle> + Definition: A phandle to the analog power supply for IC which generates + reference clock + +- phys: + Usage: required for apq8084 + Value type: <phandle> + Definition: List of phandle(s) as listed in phy-names property + +- phy-names: + Usage: required for apq8084 + Value type: <stringlist> + Definition: Should contain "pciephy" + +- <name>-gpios: + Usage: optional + Value type: <prop-encoded-array> + Definition: List of phandle and gpio specifier pairs. Should contain + - "perst-gpios" PCIe endpoint reset signal line + - "wake-gpios" PCIe endpoint wake signal line + +* Example for ipq/apq8064 + pcie@1b500000 { + compatible = "qcom,pcie-apq8064", "qcom,pcie-ipq8064", "snps,dw-pcie"; + reg = <0x1b500000 0x1000 + 0x1b502000 0x80 + 0x1b600000 0x100 + 0x0ff00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */ + 0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */ + interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc PCIE_A_CLK>, + <&gcc PCIE_H_CLK>, + <&gcc PCIE_PHY_CLK>; + clock-names = "core", "iface", "phy"; + resets = <&gcc PCIE_ACLK_RESET>, + <&gcc PCIE_HCLK_RESET>, + <&gcc PCIE_POR_RESET>, + <&gcc PCIE_PCI_RESET>, + <&gcc PCIE_PHY_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy"; + pinctrl-0 = <&pcie_pins_default>; + pinctrl-names = "default"; + }; + +* Example for apq8084 + pcie0@fc520000 { + compatible = "qcom,pcie-apq8084", "snps,dw-pcie"; + reg = <0xfc520000 0x2000>, + <0xff000000 0x1000>, + <0xff001000 0x1000>, + <0xff002000 0x2000>; + reg-names = "parf", "dbi", "elbi", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0 0xff200000 0 0x00100000 /* I/O */ + 0x82000000 0 0x00300000 0xff300000 0 0x00d00000>; /* memory */ + interrupts = <GIC_SPI 243 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>; + clock-names = "iface", "master_bus", "slave_bus", "aux"; + resets = <&gcc GCC_PCIE_0_BCR>; + reset-names = "core"; + power-domains = <&gcc PCIE0_GDSC>; + vdda-supply = <&pma8084_l3>; + phys = <&pciephy0>; + phy-names = "pciephy"; + perst-gpio = <&tlmm 70 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins_default>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 29d3b989d3b0..558fe528ae19 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -1,8 +1,16 @@ * Renesas RCar PCIe interface Required properties: -- compatible: should contain one of the following - "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; + "renesas,pcie-r8a7790" for the R8A7790 SoC; + "renesas,pcie-r8a7791" for the R8A7791 SoC; + "renesas,pcie-r8a7795" for the R8A7795 SoC; + "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: base address and length of the pcie controller registers. - #address-cells: set to <3> - #size-cells: set to <2> @@ -25,7 +33,7 @@ Example: SoC specific DT Entry: pcie: pcie@fe000000 { - compatible = "renesas,pcie-r8a7791"; + compatible = "renesas,pcie-r8a7791", "renesas,pcie-rcar-gen2"; reg = <0 0xfe000000 0 0x80000>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt new file mode 100644 index 000000000000..cafe2197dad9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt @@ -0,0 +1,18 @@ +* Atheros AR71XX/9XXX USB PHY + +Required properties: +- compatible: "qca,ar7100-usb-phy" +- #phys-cells: should be 0 +- reset-names: "usb-phy"[, "usb-suspend-override"] +- resets: references to the reset controllers + +Example: + + usb-phy { + compatible = "qca,ar7100-usb-phy"; + + reset-names = "usb-phy", "usb-suspend-override"; + resets = <&rst 4>, <&rst 3>; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt index cfe1db3bb6e9..74b5bc5dd19a 100644 --- a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt @@ -6,7 +6,12 @@ Required properties: Examples: -pwm@0x4005C000 { +pwm@4005c000 { compatible = "nxp,lpc3220-pwm"; - reg = <0x4005C000 0x8>; + reg = <0x4005c000 0x4>; +}; + +pwm@4005c004 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005c004 0x4>; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt new file mode 100644 index 000000000000..5befb538db95 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt @@ -0,0 +1,18 @@ +* OMAP PWM for dual-mode timers + +Required properties: +- compatible: Shall contain "ti,omap-dmtimer-pwm". +- ti,timers: phandle to PWM capable OMAP timer. See arm/omap/timer.txt for info + about these timers. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Optional properties: +- ti,prescaler: Should be a value between 0 and 7, see the timers datasheet + +Example: + pwm9: dmtimer-pwm@9 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer9>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt b/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt new file mode 100644 index 000000000000..8f14df9d1205 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt @@ -0,0 +1,34 @@ +TI LMU LM363x regulator device tree bindings + +LM363x regulator driver supports LM3631 and LM3632. +LM3631 has five regulators and LM3632 supports three regulators. + +Required property: + - compatible: "ti,lm363x-regulator" + +Optional properties: + LM3632 has external enable pins for two LDOs. + - ti,lcm-en1-gpio: A GPIO specifier for Vpos control pin. + - ti,lcm-en2-gpio: A GPIO specifier for Vneg control pin. + +Child nodes: + LM3631 + - vboost + - vcont + - voref + - vpos + - vneg + + LM3632 + - vboost + - vpos + - vneg + + Optional properties of a child node: + Each sub-node should contain the constraints and initialization. + Please refer to [1]. + +Examples: Please refer to ti-lmu dt-bindings [2]. + +[1] ../regulator/regulator.txt +[2] ../mfd/ti-lmu.txt diff --git a/Documentation/devicetree/bindings/regulator/pv88060.txt b/Documentation/devicetree/bindings/regulator/pv88060.txt new file mode 100644 index 000000000000..10a6dadc008e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88060.txt @@ -0,0 +1,124 @@ +* Powerventure Semiconductor PV88060 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88060". +- reg: I2C slave address, usually 0x49. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4, + SW5, and SW6. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88060@49 { + compatible = "pvs,pv88060"; + reg = <0x49>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <4387500>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + regulator-boot-on; + }; + + LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + SW1 { + regulator-name = "sw1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + SW2 { + regulator-name = "sw2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW3 { + regulator-name = "sw3"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW4 { + regulator-name = "sw4"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW5 { + regulator-name = "sw5"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW6 { + regulator-name = "sw6"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + }; + };
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/regulator/pv88090.txt b/Documentation/devicetree/bindings/regulator/pv88090.txt new file mode 100644 index 000000000000..e52b2a95cdde --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88090.txt @@ -0,0 +1,65 @@ +* Powerventure Semiconductor PV88090 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88090". +- reg: I2C slave address, usually 0x48. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, BUCK2, BUCK3, LDO1, and LDO2. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88090@48 { + compatible = "pvs,pv88090"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = < 220000>; + regulator-max-microamp = <7040000>; + regulator-boot-on; + }; + + BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + + BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + regulator-boot-on; + }; + + LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <4350000>; + regulator-boot-on; + }; + + LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = < 650000>; + regulator-max-microvolt = <2225000>; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index e27f5c4c54fd..1f8d6f84b657 100644 --- a/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -1,27 +1,17 @@ -Qualcomm Resource Power Manager (RPM) over SMD +QCOM SMD RPM REGULATOR -This driver is used to interface with the Resource Power Manager (RPM) found in -various Qualcomm platforms. The RPM allows each component in the system to vote -for state of the system resources, such as clocks, regulators and bus -frequencies. +The Qualcomm RPM over SMD regulator is modelled as a subdevice of the RPM. +Because SMD is used as the communication transport mechanism, the RPM resides as +a subnode of the SMD. As such, the SMD-RPM regulator requires that the SMD and +RPM nodes be present. -- compatible: - Usage: required - Value type: <string> - Definition: must be one of: - "qcom,rpm-msm8974" +Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt for +information pertaining to the SMD node. -- qcom,smd-channels: - Usage: required - Value type: <stringlist> - Definition: Shared Memory channel used for communication with the RPM +Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt for +information regarding the RPM node. -= SUBDEVICES - -The RPM exposes resources to its subnodes. The below bindings specify the set -of valid subnodes that can operate on these resources. - -== Regulators +== Regulator Regulator nodes are identified by their compatible: @@ -30,7 +20,9 @@ Regulator nodes are identified by their compatible: Value type: <string> Definition: must be one of: "qcom,rpm-pm8841-regulators" + "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pma8084-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -48,6 +40,19 @@ Regulator nodes are identified by their compatible: - vdd_s1-supply: - vdd_s2-supply: - vdd_s3-supply: +- vdd_s4-supply: +- vdd_l1_l2_l3-supply: +- vdd_l4_l5_l6-supply: +- vdd_l7-supply: +- vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18-supply: + Usage: optional (pm8916 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: - vdd_l1_l3-supply: - vdd_l2_lvs1_2_3-supply: - vdd_l4_l11-supply: @@ -63,6 +68,35 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vdd_s9-supply: +- vdd_s10-supply: +- vdd_s11-supply: +- vdd_s12-supply: +- vdd_l1_l11-supply: +- vdd_l2_l3_l4_l27-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l14_l15_l26-supply: +- vdd_l8-supply: +- vdd_l9_l10_l13_l20_l23_l24-supply: +- vdd_l16_l25-supply: +- vdd_l17-supply: +- vdd_l18-supply: +- vdd_l19-supply: +- vdd_l21-supply: +- vdd_l22-supply: + Usage: optional (pma8084 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -70,11 +104,20 @@ of the pmics below. pm8841: s1, s2, s3, s4, s5, s6, s7, s8 +pm8916: + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18 + pm8941: s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, 5vs1, 5vs2 +pma8084: + s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, + l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, + l21, l22, l23, l24, l25, l26, l27, lvs1, lvs2, lvs3, lvs4, 5vs1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. @@ -114,4 +157,3 @@ see regulator.txt. }; }; }; - diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index 4f05d208c95c..d18109657da6 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -26,7 +26,11 @@ Example: ti,pmic-shutdown-controller; regulators { + #address-cells = <1>; + #size-cells = <0>; + dcdc1_reg: dcdc1 { + reg = <0>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -34,6 +38,7 @@ Example: }; dcdc2_reg: dcdc2 { + reg = <1>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -41,6 +46,7 @@ Example: }; dcdc3_reg: dcc3 { + reg = <2>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; @@ -48,6 +54,7 @@ Example: }; ldo1_reg: ldo1 { + reg = <3>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -55,6 +62,7 @@ Example: }; ldo2_reg: ldo2 { + reg = <4>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -62,6 +70,7 @@ Example: }; ldo3_reg: ldo3 { + reg = <5>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -69,6 +78,7 @@ Example: }; ldo4_reg: ldo4 { + reg = <6>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt new file mode 100644 index 000000000000..e0b185a944ba --- /dev/null +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -0,0 +1,34 @@ +Hisilicon System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller registers are part of the system-ctl block on +hi6220 SoC. + +Required properties: +- compatible: may be "hisilicon,hi6220-sysctrl" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +Example: +sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== +example: + + uart1: serial@..... { + ... + resets = <&sys_ctrl PERIPH_RSTEN3_UART1>; + ... + }; + +The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>. diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 91d5ab0e60fc..936ab5b87324 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -14,7 +14,6 @@ Required properties: tegra132, or tegra210. - "nxp,lpc3220-uart" - "ralink,rt2880-uart" - - "ibm,qpace-nwp-serial" - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 2d47add34765..a833a016f656 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -2,15 +2,15 @@ Required properties: - compatible should contain: - * "mediatek,mt8135-uart" for MT8135 compatible UARTS + * "mediatek,mt2701-uart" for MT2701 compatible UARTS + * "mediatek,mt6580-uart" for MT6580 compatible UARTS + * "mediatek,mt6582-uart" for MT6582 compatible UARTS + * "mediatek,mt6589-uart" for MT6589 compatible UARTS + * "mediatek,mt6795-uart" for MT6795 compatible UARTS * "mediatek,mt8127-uart" for MT8127 compatible UARTS + * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS - * "mediatek,mt6795-uart" for MT6795 compatible UARTS - * "mediatek,mt6589-uart" for MT6589 compatible UARTS - * "mediatek,mt6582-uart" for MT6582 compatible UARTS - * "mediatek,mt6580-uart" for MT6580 compatible UARTS - * "mediatek,mt6577-uart" for all compatible UARTS (MT8173, MT6795, - MT6589, MT6582, MT6580, MT6577) + * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt new file mode 100644 index 000000000000..30942cf7992b --- /dev/null +++ b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt @@ -0,0 +1,47 @@ +Raspberry Pi power domain driver + +Required properties: + +- compatible: Should be "raspberrypi,bcm2835-power". +- firmware: Reference to the RPi firmware device node. +- #power-domain-cells: Should be <1>, we providing multiple power domains. + +The valid defines for power domain are: + + RPI_POWER_DOMAIN_I2C0 + RPI_POWER_DOMAIN_I2C1 + RPI_POWER_DOMAIN_I2C2 + RPI_POWER_DOMAIN_VIDEO_SCALER + RPI_POWER_DOMAIN_VPU1 + RPI_POWER_DOMAIN_HDMI + RPI_POWER_DOMAIN_USB + RPI_POWER_DOMAIN_VEC + RPI_POWER_DOMAIN_JPEG + RPI_POWER_DOMAIN_H264 + RPI_POWER_DOMAIN_V3D + RPI_POWER_DOMAIN_ISP + RPI_POWER_DOMAIN_UNICAM0 + RPI_POWER_DOMAIN_UNICAM1 + RPI_POWER_DOMAIN_CCP2RX + RPI_POWER_DOMAIN_CSI2 + RPI_POWER_DOMAIN_CPI + RPI_POWER_DOMAIN_DSI0 + RPI_POWER_DOMAIN_DSI1 + RPI_POWER_DOMAIN_TRANSPOSER + RPI_POWER_DOMAIN_CCP2TX + RPI_POWER_DOMAIN_CDP + RPI_POWER_DOMAIN_ARM + +Example: + +power: power { + compatible = "raspberrypi,bcm2835-power"; + firmware = <&firmware>; + #power-domain-cells = <1>; +}; + +Example for using power domain: + +&usb { + power-domains = <&power RPI_POWER_DOMAIN_USB>; +}; diff --git a/Documentation/devicetree/bindings/soc/dove/pmu.txt b/Documentation/devicetree/bindings/soc/dove/pmu.txt new file mode 100644 index 000000000000..edd40b796b74 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/dove/pmu.txt @@ -0,0 +1,56 @@ +Device Tree bindings for Marvell PMU + +Required properties: + - compatible: value should be "marvell,dove-pmu". + May also include "simple-bus" if there are child devices, in which + case the ranges node is required. + - reg: two base addresses and sizes of the PM controller and PMU. + - interrupts: single interrupt number for the PMU interrupt + - interrupt-controller: must be specified as the PMU itself is an + interrupt controller. + - #interrupt-cells: must be 1. + - #reset-cells: must be 1. + - domains: sub-node containing domain descriptions + +Optional properties: + - ranges: defines the address mapping for child devices, as per the + standard property of this name. Required when compatible includes + "simple-bus". + +Power domain descriptions are listed as child nodes of the "domains" +sub-node. Each domain has the following properties: + +Required properties: + - #power-domain-cells: must be 0. + +Optional properties: + - marvell,pmu_pwr_mask: specifies the mask value for PMU power register + - marvell,pmu_iso_mask: specifies the mask value for PMU isolation register + - resets: points to the reset manager (PMU node) and reset index. + +Example: + + pmu: power-management@d0000 { + compatible = "marvell,dove-pmu"; + reg = <0xd0000 0x8000>, <0xd8000 0x8000>; + interrupts = <33>; + interrupt-controller; + #interrupt-cells = <1>; + #reset-cells = <1>; + + domains { + vpu_domain: vpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000008>; + marvell,pmu_iso_mask = <0x00000001>; + resets = <&pmu 16>; + }; + + gpu_domain: gpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000004>; + marvell,pmu_iso_mask = <0x00000002>; + resets = <&pmu 18>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index a6c8afc8385a..e8f15e34027f 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -21,6 +21,18 @@ Required properties: These are the clocks which hardware needs to be enabled before enabling certain power domains. +Optional properties: +- vdec-supply: Power supply for the vdec power domain +- venc-supply: Power supply for the venc power domain +- isp-supply: Power supply for the isp power domain +- mm-supply: Power supply for the mm power domain +- venc_lt-supply: Power supply for the venc_lt power domain +- audio-supply: Power supply for the audio power domain +- usb-supply: Power supply for the usb power domain +- mfg_async-supply: Power supply for the mfg_async power domain +- mfg_2d-supply: Power supply for the mfg_2d power domain +- mfg-supply: Power supply for the mfg power domain + Example: scpsys: scpsys@10006000 { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt new file mode 100644 index 000000000000..a48049ccf6d0 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt @@ -0,0 +1,58 @@ +Qualcomm Resource Power Manager (RPM) over SMD + +This driver is used to interface with the Resource Power Manager (RPM) found in +various Qualcomm platforms. The RPM allows each component in the system to vote +for state of the system resources, such as clocks, regulators and bus +frequencies. + +The SMD information for the RPM edge should be filled out. See qcom,smd.txt for +the required edge properties. All SMD related properties will reside within the +RPM node itself. + += SUBDEVICES + +The RPM exposes resources to its subnodes. The rpm_requests node must be +present and this subnode may contain children that designate regulator +resources. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-apq8084" + "qcom,rpm-msm8916" + "qcom,rpm-msm8974" + +- qcom,smd-channels: + Usage: required + Value type: <string> + Definition: must be "rpm_requests" + +Refer to Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +for information on the regulator subnodes that can exist under the rpm_requests. + +Example: + + soc { + apcs: syscon@f9011000 { + compatible = "syscon"; + reg = <0xf9011000 0x1000>; + }; + }; + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + ... + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt new file mode 100644 index 000000000000..5cc82b8353d8 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory Point 2 Point binding + +The Shared Memory Point to Point (SMP2P) protocol facilitates communication of +a single 32-bit value between two processors. Each value has a single writer +(the local side) and a single reader (the remote side). Values are uniquely +identified in the system by the directed edge (local processor ID to remote +processor ID) and a string identifier. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smp2p" + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: one entry specifying the smp2p notification interrupt + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote end of the smp2p edge: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smem: + Usage: required + Value type: <u32 array> + Definition: two identifiers of the inbound and outbound smem items used + for this edge + +- qcom,local-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the local endpoint of this edge + +- qcom,remote-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the remote endpoint of this edge + += SUBNODES +Each SMP2P pair contain a set of inbound and outbound entries, these are +described in subnodes of the smp2p device node. The node names are not +important. + +- qcom,entry-name: + Usage: required + Value type: <string> + Definition: specifies the name of this entry, for inbound entries this + will be used to match against the remotely allocated entry + and for outbound entries this name is used for allocating + entries + +- interrupt-controller: + Usage: required for incoming entries + Value type: <empty> + Definition: marks the entry as inbound; the node should be specified + as a two cell interrupt-controller as defined in + "../interrupt-controller/interrupts.txt" + If not specified this node will denote the outgoing entry + +- #interrupt-cells: + Usage: required for incoming entries + Value type: <u32> + Definition: must be 2 - denoting the bit in the entry and IRQ flags + +- #qcom,state-cells: + Usage: required for outgoing entries + Value type: <u32> + Definition: must be 1 - denoting the bit in the entry + += EXAMPLE +The following example shows the SMP2P setup with the wireless processor, +defined from the 8974 apps processor's point-of-view. It encompasses one +inbound and one outbound entry: + +wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <431>, <451>; + + interrupts = <0 143 1>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt new file mode 100644 index 000000000000..a6634c70850d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory State Machine + +The Shared Memory State Machine facilitates broadcasting of single bit state +information between the processors in a Qualcomm SoC. Each processor is +assigned 32 bits of state that can be modified. A processor can through a +matrix of bitmaps signal subscription of notifications upon changes to a +certain bit owned by a certain remote processor. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smsm" + +- qcom,ipc-N: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the N:th remote processor + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,local-host: + Usage: optional + Value type: <u32> + Definition: identifier of the local processor in the list of hosts, or + in other words specifier of the column in the subscription + matrix representing the local processor + defaults to host 0 + +- #address-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: <u32> + Definition: must be 0 + += SUBNODES +Each processor's state bits are described by a subnode of the smsm device node. +Nodes can either be flagged as an interrupt-controller to denote a remote +processor's state bits or the local processors bits. The node names are not +important. + +- reg: + Usage: required + Value type: <u32> + Definition: specifies the offset, in words, of the first bit for this + entry + +- #qcom,state-cells: + Usage: required for local entry + Value type: <u32> + Definition: must be 1 - denotes bit number + +- interrupt-controller: + Usage: required for remote entries + Value type: <empty> + Definition: marks the entry as a interrupt-controller and the state bits + to belong to a remote processor + +- #interrupt-cells: + Usage: required for remote entries + Value type: <u32> + Definition: must be 2 - denotes bit number and IRQ flags + +- interrupts: + Usage: required for remote entries + Value type: <prop-encoded-array> + Definition: one entry specifying remote IRQ used by the remote processor + to signal changes of its state bits + + += EXAMPLE +The following example shows the SMEM setup for controlling properties of the +wireless processor, defined from the 8974 apps processor's point-of-view. It +encompasses one outbound entry and the outgoing interrupt for the wireless +processor. + +smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + qcom,ipc-3 = <&apcs 8 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,state-cells = <1>; + }; + + wcnss_smsm: wcnss@7 { + reg = <7>; + interrupts = <0 144 1>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt new file mode 100644 index 000000000000..401550487ed6 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt @@ -0,0 +1,57 @@ +Wakeup M3 IPC Driver +===================== + +The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor +(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks +that cannot be controlled from the MPU, like suspend/resume and certain deep +C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver +to boot the wkup_m3, it handles communication with the CM3 using IPC registers +present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an +API to allow the SoC PM code to execute specific PM tasks. + +Wkup M3 Device Node: +==================== +A wkup_m3_ipc device node is used to represent the IPC registers within an +SoC. + +Required properties: +-------------------- +- compatible: Should be, + "ti,am3352-wkup-m3-ipc" for AM33xx SoCs + "ti,am4372-wkup-m3-ipc" for AM43xx SoCs +- reg: Contains the IPC register address space to communicate + with the Wakeup M3 processor +- interrupts: Contains the interrupt information for the wkup_m3 + interrupt that signals the MPU. +- ti,rproc: phandle to the wkup_m3 rproc node so the IPC driver + can boot it. +- mboxes: phandles used by IPC framework to get correct mbox + channel for communication. Must point to appropriate + mbox_wkupm3 child node. + +Example: +-------- +/* AM33xx */ + l4_wkup: l4_wkup@44c00000 { + ... + + scm: scm@210000 { + compatible = "ti,am3-scm", "simple-bus"; + reg = <0x210000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x210000 0x2000>; + + ... + + wkup_m3_ipc: wkup_m3_ipc@1324 { + compatible = "ti,am3352-wkup-m3-ipc"; + reg = <0x1324 0x24>; + interrupts = <78>; + ti,rproc = <&wkup_m3>; + mboxes = <&mailbox &mbox_wkupm3>; + }; + + ... + }; + }; diff --git a/Documentation/devicetree/bindings/sound/ak4613.txt b/Documentation/devicetree/bindings/sound/ak4613.txt index 15a919522b42..1783f9ef0930 100644 --- a/Documentation/devicetree/bindings/sound/ak4613.txt +++ b/Documentation/devicetree/bindings/sound/ak4613.txt @@ -7,6 +7,16 @@ Required properties: - compatible : "asahi-kasei,ak4613" - reg : The chip select number on the I2C bus +Optional properties: +- asahi-kasei,in1-single-end : Boolean. Indicate input / output pins are single-ended. +- asahi-kasei,in2-single-end rather than differential. +- asahi-kasei,out1-single-end +- asahi-kasei,out2-single-end +- asahi-kasei,out3-single-end +- asahi-kasei,out4-single-end +- asahi-kasei,out5-single-end +- asahi-kasei,out6-single-end + Example: &i2c { diff --git a/Documentation/devicetree/bindings/sound/atmel-pdmic.txt b/Documentation/devicetree/bindings/sound/atmel-pdmic.txt new file mode 100644 index 000000000000..e0875f17c229 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-pdmic.txt @@ -0,0 +1,55 @@ +* Atmel PDMIC driver under ALSA SoC architecture + +Required properties: +- compatible + Should be "atmel,sama5d2-pdmic". +- reg + Should contain PDMIC registers location and length. +- interrupts + Should contain the IRQ line for the PDMIC. +- dmas + One DMA specifiers as described in atmel-dma.txt and dma.txt files. +- dma-names + Must be "rx". +- clock-names + Required elements: + - "pclk" peripheral clock + - "gclk" generated clock +- clocks + Must contain an entry for each required entry in clock-names. + Please refer to clock-bindings.txt. +- atmel,mic-min-freq + The minimal frequency that the micphone supports. +- atmel,mic-max-freq + The maximal frequency that the micphone supports. + +Optional properties: +- pinctrl-names, pinctrl-0 + Please refer to pinctrl-bindings.txt. +- atmel,model + The user-visible name of this sound card. + The default value is "PDMIC". +- atmel,mic-offset + The offset that should be added. + The range is from -32768 to 32767. + The default value is 0. + +Example: + pdmic@f8018000 { + compatible = "atmel,sama5d2-pdmic"; + reg = <0xf8018000 0x124>; + interrupts = <48 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(50))>; + dma-names = "rx"; + clocks = <&pdmic_clk>, <&pdmic_gclk>; + clock-names = "pclk", "gclk"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pdmic_default>; + atmel,model = "PDMIC @ sama5d2_xplained"; + atmel,mic-min-freq = <1000000>; + atmel,mic-max-freq = <3246000>; + atmel,mic-offset = <0x0>; + }; diff --git a/Documentation/devicetree/bindings/sound/da7218.txt b/Documentation/devicetree/bindings/sound/da7218.txt new file mode 100644 index 000000000000..5ca5a709b6aa --- /dev/null +++ b/Documentation/devicetree/bindings/sound/da7218.txt @@ -0,0 +1,104 @@ +Dialog Semiconductor DA7218 Audio Codec bindings + +DA7218 is an audio codec with HP detect feature. + +====== + +Required properties: +- compatible : Should be "dlg,da7217" or "dlg,da7218" +- reg: Specifies the I2C slave address + +- VDD-supply: VDD power supply for the device +- VDDMIC-supply: VDDMIC power supply for the device +- VDDIO-supply: VDDIO power supply for the device + (See Documentation/devicetree/bindings/regulator/regulator.txt for further + information relating to regulators) + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from DA7218 are delivered to. +- interrupts: IRQ line info for DA7218 chip. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + further information relating to interrupt properties) +- interrupt-names : Name associated with interrupt line. Should be "wakeup" if + interrupt is to be used to wake system, otherwise "irq" should be used. +- wakeup-source: Flag to indicate this device can wake system (suspend/resume). + +- clocks : phandle and clock specifier for codec MCLK. +- clock-names : Clock name string for 'clocks' attribute, should be "mclk". + +- dlg,micbias1-lvl-millivolt : Voltage (mV) for Mic Bias 1 + [<1200>, <1600>, <1800>, <2000>, <2200>, <2400>, <2600>, <2800>, <3000>] +- dlg,micbias2-lvl-millivolt : Voltage (mV) for Mic Bias 2 + [<1200>, <1600>, <1800>, <2000>, <2200>, <2400>, <2600>, <2800>, <3000>] +- dlg,mic1-amp-in-sel : Mic1 input source type + ["diff", "se_p", "se_n"] +- dlg,mic2-amp-in-sel : Mic2 input source type + ["diff", "se_p", "se_n"] +- dlg,dmic1-data-sel : DMIC1 channel select based on clock edge. + ["lrise_rfall", "lfall_rrise"] +- dlg,dmic1-samplephase : When to sample audio from DMIC1. + ["on_clkedge", "between_clkedge"] +- dlg,dmic1-clkrate-hz : DMic1 clock frequency (Hz). + [<1500000>, <3000000>] +- dlg,dmic2-data-sel : DMic2 channel select based on clock edge. + ["lrise_rfall", "lfall_rrise"] +- dlg,dmic2-samplephase : When to sample audio from DMic2. + ["on_clkedge", "between_clkedge"] +- dlg,dmic2-clkrate-hz : DMic2 clock frequency (Hz). + [<1500000>, <3000000>] +- dlg,hp-diff-single-supply : Boolean flag, use single supply for HP + (DA7217 only) + +====== + +Optional Child node - 'da7218_hpldet' (DA7218 only): + +Optional properties: +- dlg,jack-rate-us : Time between jack detect measurements (us) + [<5>, <10>, <20>, <40>, <80>, <160>, <320>, <640>] +- dlg,jack-debounce : Number of debounce measurements taken for jack detect + [<0>, <2>, <3>, <4>] +- dlg,jack-threshold-pct : Threshold level for jack detection (% of VDD) + [<84>, <88>, <92>, <96>] +- dlg,comp-inv : Boolean flag, invert comparator output +- dlg,hyst : Boolean flag, enable hysteresis +- dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal + +====== + +Example: + + codec: da7218@1a { + compatible = "dlg,da7218"; + reg = <0x1a>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + wakeup-source; + + VDD-supply = <®_audio>; + VDDMIC-supply = <®_audio>; + VDDIO-supply = <®_audio>; + + clocks = <&clks 201>; + clock-names = "mclk"; + + dlg,micbias1-lvl-millivolt = <2600>; + dlg,micbias2-lvl-millivolt = <2600>; + dlg,mic1-amp-in-sel = "diff"; + dlg,mic2-amp-in-sel = "diff"; + + dlg,dmic1-data-sel = "lrise_rfall"; + dlg,dmic1-samplephase = "on_clkedge"; + dlg,dmic1-clkrate-hz = <3000000>; + dlg,dmic2-data-sel = "lrise_rfall"; + dlg,dmic2-samplephase = "on_clkedge"; + dlg,dmic2-clkrate-hz = <3000000>; + + da7218_hpldet { + dlg,jack-rate-us = <40>; + dlg,jack-debounce = <2>; + dlg,jack-threshold-pct = <84>; + dlg,hyst; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/da7219.txt b/Documentation/devicetree/bindings/sound/da7219.txt index 1b7030911a3b..cf61681826b6 100644 --- a/Documentation/devicetree/bindings/sound/da7219.txt +++ b/Documentation/devicetree/bindings/sound/da7219.txt @@ -28,13 +28,15 @@ Optional properties: - clocks : phandle and clock specifier for codec MCLK. - clock-names : Clock name string for 'clocks' attribute, should be "mclk". -- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine - [<1050>, <1100>, <1200>, <1400>] - dlg,micbias-lvl : Voltage (mV) for Mic Bias - [<1800>, <2000>, <2200>, <2400>, <2600>] + [<1600>, <1800>, <2000>, <2200>, <2400>, <2600>] - dlg,mic-amp-in-sel : Mic input source type ["diff", "se_p", "se_n"] +Deprecated properties: +- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine + (LDO unavailable in production HW so property no longer required). + ====== Child node - 'da7219_aad': diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index b93362a570be..3e26a9478e57 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -25,6 +25,11 @@ Required properties: "mem" Peripheral access clock to access registers. "ipg" Peripheral clock to driver module. "asrck_<0-f>" Clock sources for input and output clock. + "spba" The spba clock is required when ASRC is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - big-endian : If this property is absent, the little endian mode will be in use as default. Otherwise, the big endian diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index d3b6b5f48010..cd3ee5d84f03 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -27,6 +27,11 @@ Required properties: derive HCK, SCK and FS. "fsys" The system clock derived from ahb clock used to derive HCK, SCK and FS. + "spba" The spba clock is required when ESAI is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - fsl,fifo-depth : The number of elements in the transmit and receive FIFOs. This number is the maximum allowed value for diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index b5ee32ee3706..4ca39ddc0417 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -27,6 +27,11 @@ Required properties: Transceiver Clock Diagram" of SoC reference manual. It can also be referred to TxClk_Source bit of register SPDIF_STC. + "spba" The spba clock is required when SPDIF is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode diff --git a/Documentation/devicetree/bindings/sound/img,i2s-in.txt b/Documentation/devicetree/bindings/sound/img,i2s-in.txt new file mode 100644 index 000000000000..423265cfc3d6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,i2s-in.txt @@ -0,0 +1,47 @@ +Imagination Technologies I2S Input Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,i2s-in" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Must include the following entry: + "sys" The system clock + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "rx" Single DMA channel used by all active I2S channels + + - img,i2s-channels : Number of I2S channels instantiated in the I2S in block + +Optional Properties: + + - interrupts : Contains the I2S in interrupts. Depending on + the configuration, there may be no interrupts, one interrupt, + or an interrupt per I2S channel. For the case where there is + one interrupt per channel, the interrupts should be listed + in ascending channel order + + - resets: Contains a phandle to the I2S in reset signal + + - reset-names: Contains the reset signal name "rst" + +Example: + +i2s_in: i2s-in@18100800 { + compatible = "img,i2s-in"; + reg = <0x18100800 0x200>; + interrupts = <GIC_SHARED 7 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 30 0xffffffff 0>; + dma-names = "rx"; + clocks = <&cr_periph SYS_CLK_I2S_IN>; + clock-names = "sys"; + img,i2s-channels = <6>; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,i2s-out.txt b/Documentation/devicetree/bindings/sound/img,i2s-out.txt new file mode 100644 index 000000000000..0159415b3338 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,i2s-out.txt @@ -0,0 +1,51 @@ +Imagination Technologies I2S Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,i2s-out" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Must include the following entries: + "sys" The system clock + "ref" The reference clock + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" Single DMA channel used by all active I2S channels + + - img,i2s-channels : Number of I2S channels instantiated in the I2S out block + + - resets: Contains a phandle to the I2S out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the I2S out interrupts. Depending on + the configuration, there may be no interrupts, one interrupt, + or an interrupt per I2S channel. For the case where there is + one interrupt per channel, the interrupts should be listed + in ascending channel order + +Example: + +i2s_out: i2s-out@18100A00 { + compatible = "img,i2s-out"; + reg = <0x18100A00 0x200>; + interrupts = <GIC_SHARED 13 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 23 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_I2S_OUT>, + <&clk_core CLK_I2S>; + clock-names = "sys", "ref"; + img,i2s-channels = <6>; + resets = <&pistachio_reset PISTACHIO_RESET_I2S_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,parallel-out.txt b/Documentation/devicetree/bindings/sound/img,parallel-out.txt new file mode 100644 index 000000000000..a3015d2a06e0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,parallel-out.txt @@ -0,0 +1,44 @@ +Imagination Technologies Parallel Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,parallel-out". + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device. + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Includes the following entries: + "sys" The system clock + "ref" The reference clock + + - resets: Contains a phandle to the parallel out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the parallel out interrupt, if present + +Example: + +parallel_out: parallel-out@18100C00 { + compatible = "img,parallel-out"; + reg = <0x18100C00 0x100>; + interrupts = <GIC_SHARED 19 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 16 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_PAUD_OUT>, + <&clk_core CLK_AUDIO_DAC>; + clock-names = "sys", "ref"; + resets = <&pistachio_reset PISTACHIO_RESET_PRL_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt b/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt new file mode 100644 index 000000000000..4cc18fc0477e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt @@ -0,0 +1,18 @@ +Pistachio internal DAC DT bindings + +Required properties: + + - compatible: "img,pistachio-internal-dac" + + - img,cr-top : Must contain a phandle to the top level control syscon + node which contains the internal dac control registers + + - VDD-supply : Digital power supply regulator (+1.8V or +3.3V) + +Examples: + +internal_dac: internal-dac { + compatible = "img,pistachio-internal-dac"; + img,cr-top = <&cr_top>; + VDD-supply = <&supply3v3>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-in.txt b/Documentation/devicetree/bindings/sound/img,spdif-in.txt new file mode 100644 index 000000000000..aab9a81f7e13 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,spdif-in.txt @@ -0,0 +1,41 @@ +Imagination Technologies SPDIF Input Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,spdif-in" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "rx" + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Includes the following entries: + "sys" The system clock + +Optional Properties: + + - resets: Should contain a phandle to the spdif in reset signal, if any + + - reset-names: Should contain the reset signal name "rst", if a + reset phandle is given + + - interrupts : Contains the spdif in interrupt, if present + +Example: + +spdif_in: spdif-in@18100E00 { + compatible = "img,spdif-in"; + reg = <0x18100E00 0x100>; + interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 15 0xffffffff 0>; + dma-names = "rx"; + clocks = <&cr_periph SYS_CLK_SPDIF_IN>; + clock-names = "sys"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-out.txt b/Documentation/devicetree/bindings/sound/img,spdif-out.txt new file mode 100644 index 000000000000..470a5191e101 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,spdif-out.txt @@ -0,0 +1,44 @@ +Imagination Technologies SPDIF Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,spdif-out" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Includes the following entries: + "sys" The system clock + "ref" The reference clock + + - resets: Contains a phandle to the spdif out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the parallel out interrupt, if present + +Example: + +spdif_out: spdif-out@18100D00 { + compatible = "img,spdif-out"; + reg = <0x18100D00 0x100>; + interrupts = <GIC_SHARED 21 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 14 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_SPDIF_OUT>, + <&clk_core CLK_SPDIF>; + clock-names = "sys", "ref"; + resets = <&pistachio_reset PISTACHIO_RESET_SPDIF_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/inno-rk3036.txt b/Documentation/devicetree/bindings/sound/inno-rk3036.txt new file mode 100644 index 000000000000..758de8e27561 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/inno-rk3036.txt @@ -0,0 +1,20 @@ +Inno audio codec for RK3036 + +Inno audio codec is integrated inside RK3036 SoC. + +Required properties: +- compatible : Should be "rockchip,rk3036-codec". +- reg : The registers of codec. +- clock-names : Should be "acodec_pclk". +- clocks : The clock of codec. +- rockchip,grf : The phandle of grf device node. + +Example: + + acodec: acodec-ana@20030000 { + compatible = "rk3036-codec"; + reg = <0x20030000 0x4000>; + rockchip,grf = <&grf>; + clock-names = "acodec_pclk"; + clocks = <&cru ACLK_VCODEC>; + }; diff --git a/Documentation/devicetree/bindings/sound/pcm1792a.txt b/Documentation/devicetree/bindings/sound/pcm179x.txt index 970ba1ed576f..4ae70d3462d6 100644 --- a/Documentation/devicetree/bindings/sound/pcm1792a.txt +++ b/Documentation/devicetree/bindings/sound/pcm179x.txt @@ -1,4 +1,4 @@ -Texas Instruments pcm1792a DT bindings +Texas Instruments pcm179x DT bindings This driver supports the SPI bus. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index c57cbd65736c..8ee0fa91e4a0 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -7,8 +7,11 @@ Required properties: "renesas,rcar_sound-gen3" if generation3 Examples with soctypes are: - "renesas,rcar_sound-r8a7778" (R-Car M1A) + - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) - "renesas,rcar_sound-r8a7791" (R-Car M2-W) + - "renesas,rcar_sound-r8a7793" (R-Car M2-N) + - "renesas,rcar_sound-r8a7794" (R-Car E2) - "renesas,rcar_sound-r8a7795" (R-Car H3) - reg : Should contain the register physical address. required register is @@ -34,6 +37,8 @@ Required properties: see below for detail. - #sound-dai-cells : it must be 0 if your system is using single DAI it must be 1 if your system is using multi DAI + +Optional properties: - #clock-cells : it must be 0 if your system has audio_clkout it must be 1 if your system has audio_clkout0/1/2/3 - clock-frequency : for all audio_clkout0/1/2/3 @@ -244,3 +249,80 @@ rcar_sound: sound@ec500000 { }; }; }; + +Example: simple sound card + + rsnd_ak4643: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; + }; + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + status = "okay"; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &src2 &dvc0>; + capture = <&ssi1 &src3 &dvc1>; + }; + }; +}; + +&ssi1 { + shared-pin; +}; + +Example: simple sound card for TDM + + rsnd_tdm: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + dai-tdm-slot-num = <6>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&xxx>; + }; + }; + +Example: simple sound card for Multi channel + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + status = "okay"; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index 962748a8d919..2b2caa281ce3 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -4,8 +4,8 @@ Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC Required properties: -- compatible : "renesas,rsrc-card,<board>" - Examples with soctypes are: +- compatible : "renesas,rsrc-card{,<board>}" + Examples with boards are: - "renesas,rsrc-card" - "renesas,rsrc-card,lager" - "renesas,rsrc-card,koelsch" diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 2267d249ca0e..b7f3a9325ebd 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -19,6 +19,7 @@ Required properties: - clock-names: should contain followings: - "i2s_hclk": clock for I2S BUS - "i2s_clk" : clock for I2S controller +- rockchip,playback-channels: max playback channels, if not set, 8 channels default. - rockchip,capture-channels: max capture channels, if not set, 2 channels default. Example for rk3288 I2S controller: @@ -31,5 +32,6 @@ i2s@ff890000 { dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; + rockchip,playback-channels = <8>; rockchip,capture-channels = <2>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5616.txt b/Documentation/devicetree/bindings/sound/rt5616.txt new file mode 100644 index 000000000000..efc48c65198d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5616.txt @@ -0,0 +1,26 @@ +RT5616 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5616". + +- reg : The I2C address of the device. + +Pins on the device (for linking into audio routes) for RT5616: + + * IN1P + * IN2P + * IN2N + * LOUTL + * LOUTR + * HPOL + * HPOR + +Example: + +codec: rt5616@1b { + compatible = "realtek,rt5616"; + reg = <0x1b>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5651.txt b/Documentation/devicetree/bindings/sound/rt5651.txt new file mode 100644 index 000000000000..3875233095f5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5651.txt @@ -0,0 +1,41 @@ +RT5651 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5651". + +- reg : The I2C address of the device. + +Optional properties: + +- realtek,in2-differential + Boolean. Indicate MIC2 input are differential, rather than single-ended. + +- realtek,dmic-en + Boolean. true if dmic is used. + +Pins on the device (for linking into audio routes) for RT5651: + + * DMIC L1 + * DMIC R1 + * IN1P + * IN2P + * IN2N + * IN3P + * HPOL + * HPOR + * LOUTL + * LOUTR + * PDML + * PDMR + +Example: + +codec: rt5651@1a { + compatible = "realtek,rt5651"; + reg = <0x1a>; + realtek,dmic-en = "true"; + realtek,in2-diff = "false"; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5659.txt b/Documentation/devicetree/bindings/sound/rt5659.txt new file mode 100644 index 000000000000..5f79e7fde032 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5659.txt @@ -0,0 +1,75 @@ +RT5659/RT5658 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5659" or "realtek,rt5658". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using IN2N pin as dmic1 data pin + 2: using GPIO5 pin as dmic1 data pin + 3: using GPIO9 pin as dmic1 data pin + 4: using GPIO11 pin as dmic1 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using IN2P pin as dmic2 data pin + 2: using GPIO6 pin as dmic2 data pin + 3: using GPIO10 pin as dmic2 data pin + 4: using GPIO12 pin as dmic2 data pin + +- realtek,jd-src + 0: No JD is used + 1: using JD3 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. +- realtek,reset-gpios : The GPIO that controls the CODEC's RESET pin. + +Pins on the device (for linking into audio routes) for RT5659/RT5658: + + * DMIC L1 + * DMIC R1 + * DMIC L2 + * DMIC R2 + * IN1P + * IN1N + * IN2P + * IN2N + * IN3P + * IN3N + * IN4P + * IN4N + * HPOL + * HPOR + * SPOL + * SPOR + * LOUTL + * LOUTR + * MONOOUT + * PDML + * PDMR + * SPDIF + +Example: + +rt5659 { + compatible = "realtek,rt5659"; + reg = <0x1b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5677.txt b/Documentation/devicetree/bindings/sound/rt5677.txt index f07078997f87..1b3c13d206ff 100644 --- a/Documentation/devicetree/bindings/sound/rt5677.txt +++ b/Documentation/devicetree/bindings/sound/rt5677.txt @@ -18,7 +18,7 @@ Required properties: Optional properties: - realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin. -- realtek,reset-gpio : The GPIO that controls the CODEC's RESET pin. +- realtek,reset-gpio : The GPIO that controls the CODEC's RESET pin. Active low. - realtek,in1-differential - realtek,in2-differential diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index c92966bd5488..0dce690f78f5 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -14,6 +14,9 @@ Required properties: - "apb": the parent APB clock for this controller - "codec": the parent module clock +Optional properties: +- allwinner,pa-gpios: gpio to enable external amplifier + Example: codec: codec@01c22c00 { #sound-dai-cells = <0>; diff --git a/Documentation/devicetree/bindings/sound/ti,pcm3168a.txt b/Documentation/devicetree/bindings/sound/ti,pcm3168a.txt new file mode 100644 index 000000000000..5d9cb84c661d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,pcm3168a.txt @@ -0,0 +1,48 @@ +Texas Instruments pcm3168a DT bindings + +This driver supports both SPI and I2C bus access for this codec + +Required properties: + + - compatible: "ti,pcm3168a" + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Includes the following entries: + "scki" The system clock + + - VDD1-supply : Digital power supply regulator 1 (+3.3V) + + - VDD2-supply : Digital power supply regulator 2 (+3.3V) + + - VCCAD1-supply : ADC power supply regulator 1 (+5V) + + - VCCAD2-supply : ADC power supply regulator 2 (+5V) + + - VCCDA1-supply : DAC power supply regulator 1 (+5V) + + - VCCDA2-supply : DAC power supply regulator 2 (+5V) + +For required properties on SPI/I2C, consult SPI/I2C device tree documentation + +Examples: + +i2c0: i2c0@0 { + + ... + + pcm3168a: audio-codec@44 { + compatible = "ti,pcm3168a"; + reg = <0x44>; + clocks = <&clk_core CLK_AUDIO>; + clock-names = "scki"; + VDD1-supply = <&supply3v3>; + VDD2-supply = <&supply3v3>; + VCCAD1-supply = <&supply5v0>; + VCCAD2-supply = <&supply5v0>; + VCCDA1-supply = <&supply5v0>; + VCCDA2-supply = <&supply5v0>; + pinctrl-names = "default"; + pinctrl-0 = <&dac_clk_pin>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/wlf,wm8974.txt b/Documentation/devicetree/bindings/sound/wlf,wm8974.txt new file mode 100644 index 000000000000..01d3a7c83419 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wlf,wm8974.txt @@ -0,0 +1,15 @@ +WM8974 audio CODEC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + - compatible: "wlf,wm8974" + - reg: the I2C address or SPI chip select number of the device + +Examples: + +codec: wm8974@1a { + compatible = "wlf,wm8974"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 601a360531a5..cc8304aa64ac 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -15,14 +15,32 @@ Recommended properties: - spi-max-frequency: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +Optional properties: +- syscon-chipselects: Handle to system control region contains QSPI + chipselect register and offset of that register. + Example: +For am4372: qspi: qspi@4b300000 { - compatible = "ti,dra7xxx-qspi"; - reg = <0x47900000 0x100>, <0x30000000 0x3ffffff>; + compatible = "ti,am4372-qspi"; + reg = <0x47900000 0x100>, <0x30000000 0x4000000>; reg-names = "qspi_base", "qspi_mmap"; #address-cells = <1>; #size-cells = <0>; spi-max-frequency = <25000000>; ti,hwmods = "qspi"; }; + +For dra7xx: +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>, + <0x5c000000 0x4000000>, + reg-names = "qspi_base", "qspi_mmap"; + syscon-chipselects = <&scm_conf 0x558>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <48000000>; + ti,hwmods = "qspi"; +}; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt new file mode 100644 index 000000000000..66223d561972 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -0,0 +1,63 @@ +* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs + +Required properties: +- compatible : Must include "fsl,qoriq-tmu". The version of the device is + determined by the TMU IP Block Revision Register (IPBRR0) at + offset 0x0BF8. + Table of correspondences between IPBRR0 values and example chips: + Value Device + ---------- ----- + 0x01900102 T1040 +- reg : Address range of TMU registers. +- interrupts : Contains the interrupt for TMU. +- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by + the SoC reference manual. The first cell is TTR0CR, the second is + TTR1CR, etc. +- fsl,tmu-calibration : A list of cell pairs containing temperature + calibration data, as specified by the SoC reference manual. + The first cell of each pair is the value to be written to TTCFGR, + and the second is the value to be written to TSCFGR. + +Example: + +tmu@f0000 { + compatible = "fsl,qoriq-tmu"; + reg = <0xf0000 0x1000>; + interrupts = <18 2 0 0>; + fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>; + fsl,tmu-calibration = <0x00000000 0x00000025 + 0x00000001 0x00000028 + 0x00000002 0x0000002d + 0x00000003 0x00000031 + 0x00000004 0x00000036 + 0x00000005 0x0000003a + 0x00000006 0x00000040 + 0x00000007 0x00000044 + 0x00000008 0x0000004a + 0x00000009 0x0000004f + 0x0000000a 0x00000054 + + 0x00010000 0x0000000d + 0x00010001 0x00000013 + 0x00010002 0x00000019 + 0x00010003 0x0000001f + 0x00010004 0x00000025 + 0x00010005 0x0000002d + 0x00010006 0x00000033 + 0x00010007 0x00000043 + 0x00010008 0x0000004b + 0x00010009 0x00000053 + + 0x00020000 0x00000010 + 0x00020001 0x00000017 + 0x00020002 0x0000001f + 0x00020003 0x00000029 + 0x00020004 0x00000031 + 0x00020005 0x0000003c + 0x00020006 0x00000042 + 0x00020007 0x0000004d + 0x00020008 0x00000056 + + 0x00030000 0x00000012 + 0x00030001 0x0000001d>; +}; diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index 0dfa60d88dd3..08efe6bc2193 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -2,8 +2,10 @@ Required properties: - compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3228-tsadc": found on RK3228 SoCs "rockchip,rk3288-tsadc": found on RK3288 SoCs "rockchip,rk3368-tsadc": found on RK3368 SoCs + "rockchip,rk3399-tsadc": found on RK3399 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 64083bc5633c..8ff54eb464dc 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -3,6 +3,7 @@ Mediatek MT6577, MT6572 and MT6589 Timers Required properties: - compatible should contain: + * "mediatek,mt2701-timer" for MT2701 compatible timers * "mediatek,mt6580-timer" for MT6580 compatible timers * "mediatek,mt6589-timer" for MT6589 compatible timers * "mediatek,mt8127-timer" for MT8127 compatible timers diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index a4f2035569ce..72e2c5a2b327 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -33,6 +33,7 @@ auo AU Optronics Corporation avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB +boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH boundary Boundary Devices Inc. brcm Broadcom Corporation @@ -123,6 +124,8 @@ jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies +kosagi Sutajio Ko-Usagi PTE Ltd. +kyo Kyocera Corporation lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. @@ -181,6 +184,7 @@ qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qemu QEMU, a generic and open source machine emulator and virtualizer qi Qi Hardware +qiaodian QiaoDian XianShi Corporation qnap QNAP Systems, Inc. radxa Radxa raidsonic RaidSonic Technology GmbH @@ -219,11 +223,13 @@ sony Sony Corporation spansion Spansion Inc. sprd Spreadtrum Communications Inc. st STMicroelectronics +startek Startek ste ST-Ericsson stericsson ST-Ericsson synology Synology, Inc. tbs TBS Technologies tcl Toby Churchill Ltd. +technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility @@ -239,6 +245,7 @@ v3 V3 Semiconductor variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium +vivante Vivante Corporation voipac Voipac Technologies s.r.o. wexler Wexler winbond Winbond Electronics corp. diff --git a/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt b/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt new file mode 100644 index 000000000000..75b265a04047 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt @@ -0,0 +1,35 @@ +Alphascale asm9260 Watchdog timer + +Required properties: + +- compatible : should be "alphascale,asm9260-wdt". +- reg : Specifies base physical address and size of the registers. +- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt +- clock-names : should be set to + "mod" - source for tick counter. + "ahb" - ahb gate. +- resets : phandle pointing to the system reset controller with + line index for the watchdog. +- reset-names : should be set to "wdt_rst". + +Optional properties: +- timeout-sec : shall contain the default watchdog timeout in seconds, + if unset, the default timeout is 30 seconds. +- alphascale,mode : three modes are supported + "hw" - hw reset (default). + "sw" - sw reset. + "debug" - no action is taken. + +Example: + +watchdog0: watchdog@80048000 { + compatible = "alphascale,asm9260-wdt"; + reg = <0x80048000 0x10>; + clocks = <&acc CLKID_SYS_WDT>, <&acc CLKID_AHB_WDT>; + clock-names = "mod", "ahb"; + interrupts = <55>; + resets = <&rst WDT_RESET>; + reset-names = "wdt_rst"; + timeout-sec = <30>; + alphascale,mode = "hw"; +}; diff --git a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt index 9200fc2d508c..ae70185d96e6 100644 --- a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -2,7 +2,7 @@ Meson SoCs Watchdog timer Required properties: -- compatible : should be "amlogic,meson6-wdt" +- compatible : should be "amlogic,meson6-wdt" or "amlogic,meson8b-wdt" - reg : Specifies base physical address and size of the registers. Example: diff --git a/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt b/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt new file mode 100644 index 000000000000..c15ef0ef609f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt @@ -0,0 +1,12 @@ +Ralink Watchdog Timers + +Required properties: +- compatible: must be "mediatek,mt7621-wdt" +- reg: physical base address of the controller and length of the register range + +Example: + + watchdog@100 { + compatible = "mediatek,mt7621-wdt"; + reg = <0x100 0x10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index af9eb5b8a253..6a00939a059a 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -2,7 +2,11 @@ Mediatek SoCs Watchdog timer Required properties: -- compatible : should be "mediatek,mt6589-wdt" +- compatible should contain: + * "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers + * "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701, + MT6589) + - reg : Specifies base physical address and size of the registers. Example: diff --git a/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt b/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt new file mode 100644 index 000000000000..5b7ec2c707d8 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt @@ -0,0 +1,18 @@ +Sigma Designs SMP86xx/SMP87xx watchdog + +Required properties: +- compatible: Should be "sigma,smp8642-wdt" +- reg: Specifies the physical address region +- clocks: Should be a phandle to the clock + +Optional properties: +- timeout-sec: watchdog timeout in seconds + +Example: + +watchdog@1fd00 { + compatible = "sigma,smp8642-wdt"; + reg = <0x1fd00 8>; + clocks = <&xtal_in_clk>; + timeout-sec = <30>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sp805-wdt.txt b/Documentation/devicetree/bindings/watchdog/sp805-wdt.txt new file mode 100644 index 000000000000..edc4f0ea54a3 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sp805-wdt.txt @@ -0,0 +1,31 @@ +* ARM SP805 Watchdog Timer (WDT) Controller + +SP805 WDT is a ARM Primecell Peripheral and has a standard-id register that +can be used to identify the peripheral type, vendor, and revision. +This value can be used for driver matching. + +As SP805 WDT is a primecell IP, it follows the base bindings specified in +'arm/primecell.txt' + +Required properties: +- compatible : Should be "arm,sp805-wdt", "arm,primecell" +- reg : Base address and size of the watchdog timer registers. +- clocks : From common clock binding. + First clock is PCLK and the second is WDOGCLK. + WDOGCLK can be equal to or be a sub-multiple of the PCLK frequency. +- clock-names : From common clock binding. + Shall be "apb_pclk" for first clock and "wdog_clk" for the + second one. + +Optional properties: +- interrupts : Should specify WDT interrupt number. + +Examples: + + cluster1_core0_watchdog: wdt@c000000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc000000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + diff --git a/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt new file mode 100644 index 000000000000..8f6caad4258d --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt @@ -0,0 +1,25 @@ +Technologic Systems Watchdog + +Required properties: +- compatible: must be "technologic,ts4800-wdt" +- syscon: phandle / integer array that points to the syscon node which + describes the FPGA's syscon registers. + - phandle to FPGA's syscon + - offset to the watchdog register + +Optional property: +- timeout-sec: contains the watchdog timeout in seconds. + +Example: + +syscon: syscon@b0010000 { + compatible = "syscon", "simple-mfd"; + reg = <0xb0010000 0x3d>; + reg-io-width = <2>; + + wdt@e { + compatible = "technologic,ts4800-wdt"; + syscon = <&syscon 0xe>; + timeout-sec = <10>; + }; +} diff --git a/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt b/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt new file mode 100644 index 000000000000..3d878184ec3f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt @@ -0,0 +1,19 @@ +Zodiac RAVE Watchdog Timer + +Required properties: +- compatible: must be "zii,rave-wdt" +- reg: i2c slave address of device, usually 0x38 + +Optional Properties: +- timeout-sec: Watchdog timeout value in seconds. +- reset-duration-ms: Duration of the pulse generated when the watchdog times + out. Value in milliseconds. + +Example: + + watchdog@38 { + compatible = "zii,rave-wdt"; + reg = <0x38>; + timeout-sec = <30>; + reset-duration-ms = <30>; + }; |