3 files changed, 10 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt
index 4611aa83531b..f20b111b502a 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/m25p80.txt
@@ -3,10 +3,13 @@
 Required properties:
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
   representing partitions.
-- compatible : Should be the manufacturer and the name of the chip. Bear in mind
-               the DT binding is not Linux-only, but in case of Linux, see the
-               "spi_nor_ids" table in drivers/mtd/spi-nor/spi-nor.c for the list
-               of supported chips.
+- compatible : May include a device-specific string consisting of the
+               manufacturer and name of the chip. Bear in mind the DT binding
+               is not Linux-only, but in case of Linux, see the "m25p_ids"
+               table in drivers/mtd/devices/m25p80.c for the list of supported
+               chips.
+               Must also include "nor-jedec" for any SPI NOR flash that can be
+               identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -22,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80";
+		compatible = "spansion,m25p80", "nor-jedec";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;
diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
index de8b517a5521..4f833e3c4f51 100644
--- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
@@ -14,7 +14,7 @@ Optional properties:
  - marvell,nand-enable-arbiter:	Set to enable the bus arbiter
  - marvell,nand-keep-config:	Set to keep the NAND controller config as set
 				by the bootloader
- - num-cs:			Number of chipselect lines to usw
+ - num-cs:			Number of chipselect lines to use
  - nand-on-flash-bbt: 		boolean to enable on flash bbt option if
 				not present false
  - nand-ecc-strength:           number of bits to correct per ECC step
diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt
index 0273adb8638c..086d6f44c4b9 100644
--- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt
@@ -21,7 +21,7 @@ Optional properties:
 - nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft",
   "soft_bch" or "none")
 
-see Documentation/devicetree/mtd/nand.txt for generic bindings.
+see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
 
 
 Examples: