diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 122 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt index 64fc82bc8928..0df6acacfaea 100644 --- a/Documentation/devicetree/bindings/arm/primecell.txt +++ b/Documentation/devicetree/bindings/arm/primecell.txt @@ -16,14 +16,31 @@ Optional properties: - clocks : From common clock binding. First clock is phandle to clock for apb pclk. Additional clocks are optional and specific to those peripherals. - clock-names : From common clock binding. Shall be "apb_pclk" for first clock. +- dmas : From common DMA binding. If present, refers to one or more dma channels. +- dma-names : From common DMA binding, needs to match the 'dmas' property. + Devices with exactly one receive and transmit channel shall name + these "rx" and "tx", respectively. +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- interrupts : one or more interrupt specifiers +- interrupt-names : names corresponding to the interrupts properties Example: serial@fff36000 { compatible = "arm,pl011", "arm,primecell"; arm,primecell-periphid = <0x00341011>; + clocks = <&pclk>; clock-names = "apb_pclk"; - + + dmas = <&dma-controller 4>, <&dma-controller 5>; + dma-names = "rx", "tx"; + + pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; + pinctrl-1 = <&uart0_sleep_mode>; + pinctrl-names = "default","sleep"; + + interrupts = <0 11 0x4>; }; diff --git a/Documentation/devicetree/bindings/ata/pata-arasan.txt b/Documentation/devicetree/bindings/ata/pata-arasan.txt index 95ec7f825ede..2aff154be84e 100644 --- a/Documentation/devicetree/bindings/ata/pata-arasan.txt +++ b/Documentation/devicetree/bindings/ata/pata-arasan.txt @@ -6,6 +6,26 @@ Required properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupt: Should contain the CF interrupt number +- clock-frequency: Interface clock rate, in Hz, one of + 25000000 + 33000000 + 40000000 + 50000000 + 66000000 + 75000000 + 100000000 + 125000000 + 150000000 + 166000000 + 200000000 + +Optional properties: +- arasan,broken-udma: if present, UDMA mode is unusable +- arasan,broken-mwdma: if present, MWDMA mode is unusable +- arasan,broken-pio: if present, PIO mode is unusable +- dmas: one DMA channel, as described in bindings/dma/dma.txt + required unless both UDMA and MWDMA mode are broken +- dma-names: the corresponding channel name, must be "data" Example: @@ -14,4 +34,6 @@ Example: reg = <0xfc000000 0x1000>; interrupt-parent = <&vic1>; interrupts = <12>; + dmas = <&dma-controller 23>; + dma-names = "data"; }; diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt new file mode 100644 index 000000000000..5d2e840ae65c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -0,0 +1,17 @@ +* ARM AMBA Primecell PL011 serial UART + +Required properties: +- compatible: must be "arm,primecell", "arm,pl011" +- reg: exactly one register range with length 0x1000 +- interrupts: exactly one interrupt specifier + +Optional properties: +- pinctrl: When present, must have one state named "sleep" + and one state named "default" +- clocks: When present, must refer to exactly one clock named + "apb_pclk" +- dmas: When present, may have one or two dma channels. + The first one must be named "rx", the second one + must be named "tx". + +See also bindings/arm/primecell.txt diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index f158fd31cfda..22ed6797216d 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -16,6 +16,11 @@ Optional properties: device will be suspended immediately - pl022,rt : indicates the controller should run the message pump with realtime priority to minimise the transfer latency on the bus (boolean) +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. SPI slave nodes must be children of the SPI master node and can @@ -32,3 +37,34 @@ contain the following properties. - pl022,wait-state : Microwire interface: Wait state - pl022,duplex : Microwire interface: Full/Half duplex + +Example: + + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma-controller 23 1>, + <&dma-controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; + diff --git a/Documentation/devicetree/bindings/timer/arm,sp804.txt b/Documentation/devicetree/bindings/timer/arm,sp804.txt new file mode 100644 index 000000000000..5cd8eee74af1 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt @@ -0,0 +1,29 @@ +ARM sp804 Dual Timers +--------------------------------------- + +Required properties: +- compatible: Should be "arm,sp804" & "arm,primecell" +- interrupts: Should contain the list of Dual Timer interrupts. This is the + interrupt for timer 1 and timer 2. In the case of a single entry, it is + the combined interrupt or if "arm,sp804-has-irq" is present that + specifies which timer interrupt is connected. +- reg: Should contain location and length for dual timer register. +- clocks: clocks driving the dual timer hardware. This list should be 1 or 3 + clocks. With 3 clocks, the order is timer0 clock, timer1 clock, + apb_pclk. A single clock can also be specified if the same clock is + used for all clock inputs. + +Optional properties: +- arm,sp804-has-irq = <#>: In the case of only 1 timer irq line connected, this + specifies if the irq connection is for timer 1 or timer 2. A value of 1 + or 2 should be used. + +Example: + + timer0: timer@fc800000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0xfc800000 0x1000>; + interrupts = <0 0 4>, <0 1 4>; + clocks = <&timclk1 &timclk2 &pclk>; + clock-names = "timer1", "timer2", "apb_pclk"; + }; |