diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 8 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/fb/sm501fb.txt b/Documentation/devicetree/bindings/fb/sm501fb.txt index 7d319fba9b5b..9d9f0098092b 100644 --- a/Documentation/devicetree/bindings/fb/sm501fb.txt +++ b/Documentation/devicetree/bindings/fb/sm501fb.txt @@ -18,9 +18,9 @@ Optional properties: - edid : verbatim EDID data block describing attached display. Data from the detailed timing descriptor will be used to program the display controller. -- little-endian: availiable on big endian systems, to +- little-endian: available on big endian systems, to set different foreign endian. -- big-endian: availiable on little endian systems, to +- big-endian: available on little endian systems, to set different foreign endian. Example for MPC5200: diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt index a48b2cadc7f0..00f1f546b32e 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -15,7 +15,7 @@ Optional properties: - gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins (R/B#). For multi-chip devices, "n" GPIO definitions are required according to the number of chips. -- chip-delay : chip dependent delay for transfering data from array to +- chip-delay : chip dependent delay for transferring data from array to read registers (tR). Required if property "gpios" is not used (R/B# pins not connected). diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt index d6d209ded937..c2dbcec0ee31 100644 --- a/Documentation/devicetree/bindings/net/can/sja1000.txt +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -39,7 +39,7 @@ Optional properties: - nxp,no-comparator-bypass : Allows to disable the CAN input comperator. -For futher information, please have a look to the SJA1000 data sheet. +For further information, please have a look to the SJA1000 data sheet. Examples: diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt index 8aa10f45ebe6..4f6145859aab 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -199,7 +199,7 @@ EXAMPLE 4 EXAMPLE 5 /* - * Definition of an error interrupt (interupt type 1). + * Definition of an error interrupt (interrupt type 1). * SoC interrupt number is 16 and the specific error * interrupt bit in the error interrupt summary register * is 23. diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 55fd2623445b..50619a0720a8 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -138,7 +138,7 @@ and properties to be present. This will be described in detail in section III, but, for example, the kernel does not require you to create a node for every PCI device in the system. It is a requirement to have a node for PCI host bridges in order to provide interrupt -routing informations and memory/IO ranges, among others. It is also +routing information and memory/IO ranges, among others. It is also recommended to define nodes for on chip devices and other buses that don't specifically fit in an existing OF specification. This creates a great flexibility in the way the kernel can then probe those and match @@ -385,7 +385,7 @@ struct boot_param_header { among others, by kexec. If you are on an SMP system, this value should match the content of the "reg" property of the CPU node in the device-tree corresponding to the CPU calling the kernel entry - point (see further chapters for more informations on the required + point (see further chapters for more information on the required device-tree contents) - size_dt_strings @@ -553,7 +553,7 @@ looks like in practice. This tree is almost a minimal tree. It pretty much contains the minimal set of required nodes and properties to boot a linux kernel; -that is, some basic model informations at the root, the CPUs, and the +that is, some basic model information at the root, the CPUs, and the physical memory layout. It also includes misc information passed through /chosen, like in this example, the platform type (mandatory) and the kernel command line arguments (optional). |