diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
5 files changed, 139 insertions, 31 deletions
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index dc975064fa27..64ee489571c4 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -38,6 +38,8 @@ Optional properties: specifiers, one for transmission, and one for reception. - dma-names : Must contain a list of two DMA names, "tx" and "rx". +- spi-slave : Empty property indicating the SPI controller is used + in slave mode. - renesas,dtdl : delay sync signal (setup) in transmit mode. Must contain one of the following values: 0 (no bit delay) diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 4b1d6e74c744..1f6e86f787ef 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -1,17 +1,23 @@ SPI (Serial Peripheral Interface) busses -SPI busses can be described with a node for the SPI master device -and a set of child nodes for each SPI slave on the bus. For this -discussion, it is assumed that the system's SPI controller is in -SPI master mode. This binding does not describe SPI controllers -in slave mode. +SPI busses can be described with a node for the SPI controller device +and a set of child nodes for each SPI slave on the bus. The system's SPI +controller may be described for use in SPI master mode or in SPI slave mode, +but not for both at the same time. -The SPI master node requires the following properties: +The SPI controller node requires the following properties: +- compatible - Name of SPI bus controller following generic names + recommended practice. + +In master mode, the SPI controller node requires the following additional +properties: - #address-cells - number of cells required to define a chip select address on the SPI bus. - #size-cells - should be zero. -- compatible - name of SPI bus controller following generic names - recommended practice. + +In slave mode, the SPI controller node requires one additional property: +- spi-slave - Empty property. + No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -21,7 +27,7 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. -Optional properties: +Optional properties (master mode only): - cs-gpios - gpios chip select. - num-cs - total number of chipselects. @@ -41,28 +47,36 @@ cs1 : native cs2 : &gpio1 1 0 cs3 : &gpio1 2 0 -SPI slave nodes must be children of the SPI master node and can -contain the following properties. -- reg - (required) chip select address of device. -- compatible - (required) name of SPI device following generic names - recommended practice. -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz. -- spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode. -- spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode. -- spi-cs-high - (optional) Empty property indicating device requires - chip select active high. -- spi-3wire - (optional) Empty property indicating device requires - 3-wire mode. -- spi-lsb-first - (optional) Empty property indicating device requires - LSB first mode. -- spi-tx-bus-width - (optional) The bus width (number of data wires) that is - used for MOSI. Defaults to 1 if not present. -- spi-rx-bus-width - (optional) The bus width (number of data wires) that is - used for MISO. Defaults to 1 if not present. -- spi-rx-delay-us - (optional) Microsecond delay after a read transfer. -- spi-tx-delay-us - (optional) Microsecond delay after a write transfer. + +SPI slave nodes must be children of the SPI controller node. + +In master mode, one or more slave nodes (up to the number of chip selects) can +be present. Required properties are: +- compatible - Name of SPI device following generic names recommended + practice. +- reg - Chip select address of device. +- spi-max-frequency - Maximum SPI clocking speed of device in Hz. + +In slave mode, the (single) slave node is optional. +If present, it must be called "slave". Required properties are: +- compatible - Name of SPI device following generic names recommended + practice. + +All slave nodes can contain the following optional properties: +- spi-cpol - Empty property indicating device requires inverse clock + polarity (CPOL) mode. +- spi-cpha - Empty property indicating device requires shifted clock + phase (CPHA) mode. +- spi-cs-high - Empty property indicating device requires chip select + active high. +- spi-3wire - Empty property indicating device requires 3-wire mode. +- spi-lsb-first - Empty property indicating device requires LSB first mode. +- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI. + Defaults to 1 if not present. +- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO. + Defaults to 1 if not present. +- spi-rx-delay-us - Microsecond delay after a read transfer. +- spi-tx-delay-us - Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index dc6d0313324a..825c39cae74a 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -20,3 +20,34 @@ Required properties: #address-cells = <1>; #size-cells = <0>; }; + +* SPICC (SPI Communication Controller) + +The Meson SPICC is generic SPI controller for general purpose Full-Duplex +communications with dedicated 16 words RX/TX PIO FIFOs. + +Required properties: + - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs. + - reg: physical base address and length of the controller registers + - interrupts: The interrupt specifier + - clock-names: Must contain "core" + - clocks: phandle of the input clock for the baud rate generator + - #address-cells: should be 1 + - #size-cells: should be 0 + +Optional properties: + - resets: phandle of the internal reset line + +See ../spi/spi-bus.txt for more details on SPI bus master and slave devices +required and optional properties. + +Example : + spi@c1108d80 { + compatible = "amlogic,meson-gx-spicc"; + reg = <0xc1108d80 0x80>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core"; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index e43f4cf4cf35..e0318cf92d73 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -3,7 +3,9 @@ Binding for MTK SPI controller Required properties: - compatible: should be one of the following. - mediatek,mt2701-spi: for mt2701 platforms + - mediatek,mt2712-spi: for mt2712 platforms - mediatek,mt6589-spi: for mt6589 platforms + - mediatek,mt7622-spi: for mt7622 platforms - mediatek,mt8135-spi: for mt8135 platforms - mediatek,mt8173-spi: for mt8173 platforms diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt new file mode 100644 index 000000000000..1b3fa2c119d5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt @@ -0,0 +1,59 @@ +STMicroelectronics STM32 SPI Controller + +The STM32 SPI controller is used to communicate with external devices using +the Serial Peripheral Interface. It supports full-duplex, half-duplex and +simplex synchronous serial communication with external devices. It supports +from 4 to 32-bit data size. Although it can be configured as master or slave, +only master is supported by the driver. + +Required properties: +- compatible: Must be "st,stm32h7-spi". +- reg: Offset and length of the device's register set. +- interrupts: Must contain the interrupt id. +- clocks: Must contain an entry for spiclk (which feeds the internal clock + generator). +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- resets: Must contain the phandle to the reset controller. +- A pinctrl state named "default" may be defined to set pins in mode of + operation for SPI transfer. +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. +- dma-names: DMA request names should include "tx" and "rx" if present. +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Optional properties: +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in + nanoseconds inserted between two consecutive data frames. + + +Example: + spi2: spi@40003800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x40003800 0x400>; + interrupts = <36>; + clocks = <&rcc SPI2_CK>; + resets = <&rcc 1166>; + dmas = <&dmamux1 0 39 0x400 0x01>, + <&dmamux1 1 40 0x400 0x01>; + dma-names = "rx", "tx"; + pinctrl-0 = <&spi2_pins_b>; + pinctrl-names = "default"; + cs-gpios = <&gpioa 11 0>; + + aardvark@0 { + compatible = "totalphase,aardvark"; + reg = <0>; + spi-max-frequency = <4000000>; + st,spi-midi-ns = <4000>; + }; + }; |