diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
26 files changed, 1190 insertions, 406 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index b864916e087f..fc3dd7ec0445 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -95,6 +95,10 @@ wants to support one of the below features, it should adapt these bindings. - smbus-alert states that the optional SMBus-Alert feature apply to this bus. +- mctp-controller + indicates that the system is accessible via this bus as an endpoint for + MCTP over I2C transport. + Required properties (per child device) -------------------------------------- diff --git a/Documentation/devicetree/bindings/net/can/allwinner,sun4i-a10-can.yaml b/Documentation/devicetree/bindings/net/can/allwinner,sun4i-a10-can.yaml index c93fe9d3ea82..3c51b2d02957 100644 --- a/Documentation/devicetree/bindings/net/can/allwinner,sun4i-a10-can.yaml +++ b/Documentation/devicetree/bindings/net/can/allwinner,sun4i-a10-can.yaml @@ -10,6 +10,9 @@ maintainers: - Chen-Yu Tsai <wens@csie.org> - Maxime Ripard <mripard@kernel.org> +allOf: + - $ref: can-controller.yaml# + properties: compatible: oneOf: diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml index 401ab7cdb379..b7f9803c1c6d 100644 --- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml +++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml @@ -9,7 +9,10 @@ title: Bosch MCAN controller Bindings description: Bosch MCAN controller for CAN bus maintainers: - - Sriram Dash <sriram.dash@samsung.com> + - Chandrasekar Ramakrishnan <rcsekar@samsung.com> + +allOf: + - $ref: can-controller.yaml# properties: compatible: @@ -66,8 +69,8 @@ properties: M_CAN includes the following elements according to user manual: 11-bit Filter 0-128 elements / 0-128 words 29-bit Filter 0-64 elements / 0-128 words - Rx FIFO 0 0-64 elements / 0-1152 words - Rx FIFO 1 0-64 elements / 0-1152 words + Rx FIFO 0 0-64 elements / 0-1152 words + Rx FIFO 1 0-64 elements / 0-1152 words Rx Buffers 0-64 elements / 0-1152 words Tx Event FIFO 0-32 elements / 0-64 words Tx Buffers 0-32 elements / 0-576 words diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251xfd.yaml b/Documentation/devicetree/bindings/net/can/microchip,mcp251xfd.yaml index 2a884c1fe0e0..b3826af6bd6e 100644 --- a/Documentation/devicetree/bindings/net/can/microchip,mcp251xfd.yaml +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251xfd.yaml @@ -11,6 +11,9 @@ title: maintainers: - Marc Kleine-Budde <mkl@pengutronix.de> +allOf: + - $ref: can-controller.yaml# + properties: compatible: oneOf: diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml index 546c6e6d2fb0..91a3554ca950 100644 --- a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml @@ -35,6 +35,8 @@ properties: - renesas,r9a07g044-canfd # RZ/G2{L,LC} - const: renesas,rzg2l-canfd # RZ/G2L family + - const: renesas,r8a779a0-canfd # R-Car V3U + reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/net/can/xilinx,can.yaml b/Documentation/devicetree/bindings/net/can/xilinx,can.yaml new file mode 100644 index 000000000000..65af8183cb9c --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/xilinx,can.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/xilinx,can.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Xilinx Axi CAN/Zynq CANPS controller + +maintainers: + - Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com> + +properties: + compatible: + enum: + - xlnx,zynq-can-1.0 + - xlnx,axi-can-1.00.a + - xlnx,canfd-1.0 + - xlnx,canfd-2.0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + maxItems: 2 + + power-domains: + maxItems: 1 + + tx-fifo-depth: + $ref: "/schemas/types.yaml#/definitions/uint32" + description: CAN Tx fifo depth (Zynq, Axi CAN). + + rx-fifo-depth: + $ref: "/schemas/types.yaml#/definitions/uint32" + description: CAN Rx fifo depth (Zynq, Axi CAN, CAN FD in sequential Rx mode) + + tx-mailbox-count: + $ref: "/schemas/types.yaml#/definitions/uint32" + description: CAN Tx mailbox buffer count (CAN FD) + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +allOf: + - $ref: can-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - xlnx,zynq-can-1.0 + + then: + properties: + clock-names: + items: + - const: can_clk + - const: pclk + required: + - tx-fifo-depth + - rx-fifo-depth + + - if: + properties: + compatible: + contains: + enum: + - xlnx,axi-can-1.00.a + + then: + properties: + clock-names: + items: + - const: can_clk + - const: s_axi_aclk + required: + - tx-fifo-depth + - rx-fifo-depth + + - if: + properties: + compatible: + contains: + enum: + - xlnx,canfd-1.0 + - xlnx,canfd-2.0 + + then: + properties: + clock-names: + items: + - const: can_clk + - const: s_axi_aclk + required: + - tx-mailbox-count + - rx-fifo-depth + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + can@e0008000 { + compatible = "xlnx,zynq-can-1.0"; + reg = <0xe0008000 0x1000>; + clocks = <&clkc 19>, <&clkc 36>; + clock-names = "can_clk", "pclk"; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&intc>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; + + - | + can@40000000 { + compatible = "xlnx,axi-can-1.00.a"; + reg = <0x40000000 0x10000>; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk", "s_axi_aclk"; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; + + - | + can@40000000 { + compatible = "xlnx,canfd-1.0"; + reg = <0x40000000 0x2000>; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk", "s_axi_aclk"; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>; + tx-mailbox-count = <0x20>; + rx-fifo-depth = <0x20>; + }; + + - | + can@ff060000 { + compatible = "xlnx,canfd-2.0"; + reg = <0xff060000 0x6000>; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk", "s_axi_aclk"; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>; + tx-mailbox-count = <0x20>; + rx-fifo-depth = <0x40>; + }; diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt deleted file mode 100644 index 100cc40b8510..000000000000 --- a/Documentation/devicetree/bindings/net/can/xilinx_can.txt +++ /dev/null @@ -1,61 +0,0 @@ -Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings ---------------------------------------------------------- - -Required properties: -- compatible : Should be: - - "xlnx,zynq-can-1.0" for Zynq CAN controllers - - "xlnx,axi-can-1.00.a" for Axi CAN controllers - - "xlnx,canfd-1.0" for CAN FD controllers - - "xlnx,canfd-2.0" for CAN FD 2.0 controllers -- reg : Physical base address and size of the controller - registers map. -- interrupts : Property with a value describing the interrupt - number. -- clock-names : List of input clock names - - "can_clk", "pclk" (For CANPS), - - "can_clk", "s_axi_aclk" (For AXI CAN and CAN FD). - (See clock bindings for details). -- clocks : Clock phandles (see clock bindings for details). -- tx-fifo-depth : Can Tx fifo depth (Zynq, Axi CAN). -- rx-fifo-depth : Can Rx fifo depth (Zynq, Axi CAN, CAN FD in - sequential Rx mode). -- tx-mailbox-count : Can Tx mailbox buffer count (CAN FD). -- rx-mailbox-count : Can Rx mailbox buffer count (CAN FD in mailbox Rx - mode). - - -Example: - -For Zynq CANPS Dts file: - zynq_can_0: can@e0008000 { - compatible = "xlnx,zynq-can-1.0"; - clocks = <&clkc 19>, <&clkc 36>; - clock-names = "can_clk", "pclk"; - reg = <0xe0008000 0x1000>; - interrupts = <0 28 4>; - interrupt-parent = <&intc>; - tx-fifo-depth = <0x40>; - rx-fifo-depth = <0x40>; - }; -For Axi CAN Dts file: - axi_can_0: axi-can@40000000 { - compatible = "xlnx,axi-can-1.00.a"; - clocks = <&clkc 0>, <&clkc 1>; - clock-names = "can_clk","s_axi_aclk" ; - reg = <0x40000000 0x10000>; - interrupt-parent = <&intc>; - interrupts = <0 59 1>; - tx-fifo-depth = <0x40>; - rx-fifo-depth = <0x40>; - }; -For CAN FD Dts file: - canfd_0: canfd@40000000 { - compatible = "xlnx,canfd-1.0"; - clocks = <&clkc 0>, <&clkc 1>; - clock-names = "can_clk", "s_axi_aclk"; - reg = <0x40000000 0x2000>; - interrupt-parent = <&intc>; - interrupts = <0 59 1>; - tx-mailbox-count = <0x20>; - rx-fifo-depth = <0x20>; - }; diff --git a/Documentation/devicetree/bindings/net/cdns,macb.yaml b/Documentation/devicetree/bindings/net/cdns,macb.yaml index 8dd06db34169..6cd3d853dcba 100644 --- a/Documentation/devicetree/bindings/net/cdns,macb.yaml +++ b/Documentation/devicetree/bindings/net/cdns,macb.yaml @@ -81,6 +81,25 @@ properties: phy-handle: true + phys: + maxItems: 1 + + phy-names: + const: sgmii-phy + description: + Required with ZynqMP SoC when in SGMII mode. + Should reference PS-GTR generic PHY device for this controller + instance. See ZynqMP example. + + resets: + maxItems: 1 + description: + Recommended with ZynqMP, specify reset control for this + controller instance with zynqmp-reset driver. + + reset-names: + maxItems: 1 + fixed-link: true iommus: @@ -157,3 +176,40 @@ examples: reset-gpios = <&pioE 6 1>; }; }; + + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/power/xlnx-zynqmp-power.h> + #include <dt-bindings/reset/xlnx-zynqmp-resets.h> + #include <dt-bindings/phy/phy.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + gem1: ethernet@ff0c0000 { + compatible = "cdns,zynqmp-gem", "cdns,gem"; + interrupt-parent = <&gic>; + interrupts = <0 59 4>, <0 59 4>; + reg = <0x0 0xff0c0000 0x0 0x1000>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, + <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>, + <&zynqmp_clk GEM_TSU>; + clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; + #address-cells = <1>; + #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x875>; + power-domains = <&zynqmp_firmware PD_ETH_1>; + resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>; + reset-names = "gem1_rst"; + status = "okay"; + phy-mode = "sgmii"; + phy-names = "sgmii-phy"; + phys = <&psgtr 1 PHY_TYPE_SGMII 1 1>; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/davicom,dm9051.yaml b/Documentation/devicetree/bindings/net/davicom,dm9051.yaml new file mode 100644 index 000000000000..52e852fef753 --- /dev/null +++ b/Documentation/devicetree/bindings/net/davicom,dm9051.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/davicom,dm9051.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Davicom DM9051 SPI Ethernet Controller + +maintainers: + - Joseph CHANG <josright123@gmail.com> + +description: | + The DM9051 is a fully integrated and cost-effective low pin count single + chip Fast Ethernet controller with a Serial Peripheral Interface (SPI). + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + const: davicom,dm9051 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 45000000 + + interrupts: + maxItems: 1 + + local-mac-address: true + + mac-address: true + +required: + - compatible + - reg + - spi-max-frequency + - interrupts + +additionalProperties: false + +examples: + # Raspberry Pi platform + - | + /* for Raspberry Pi with pin control stuff for GPIO irq */ + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + ethernet@0 { + compatible = "davicom,dm9051"; + reg = <0>; /* spi chip select */ + local-mac-address = [00 00 00 00 00 00]; + interrupt-parent = <&gpio>; + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + spi-max-frequency = <31200000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml index 702df848a71d..e60867c7c571 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -51,6 +51,8 @@ properties: - edsa - ocelot - ocelot-8021q + - rtl8_4 + - rtl8_4t - seville phy-handle: true diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml index 84985f53bffd..184152087b60 100644 --- a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -42,6 +42,12 @@ properties: description: Set if the output SYNCLKO frequency should be set to 125MHz instead of 25MHz. + microchip,synclko-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set if the output SYNCLKO clock should be disabled. Do not mix with + microchip,synclko-125. + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt deleted file mode 100644 index 7959ec237983..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt +++ /dev/null @@ -1,240 +0,0 @@ -Realtek SMI-based Switches -========================== - -The SMI "Simple Management Interface" is a two-wire protocol using -bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does -not use the MDIO protocol. This binding defines how to specify the -SMI-based Realtek devices. - -Required properties: - -- compatible: must be exactly one of: - "realtek,rtl8365mb" (4+1 ports) - "realtek,rtl8366" - "realtek,rtl8366rb" (4+1 ports) - "realtek,rtl8366s" (4+1 ports) - "realtek,rtl8367" - "realtek,rtl8367b" - "realtek,rtl8368s" (8 port) - "realtek,rtl8369" - "realtek,rtl8370" (8 port) - -Required properties: -- mdc-gpios: GPIO line for the MDC clock line. -- mdio-gpios: GPIO line for the MDIO data line. -- reset-gpios: GPIO line for the reset signal. - -Optional properties: -- realtek,disable-leds: if the LED drivers are not used in the - hardware design this will disable them so they are not turned on - and wasting power. - -Required subnodes: - -- interrupt-controller - - This defines an interrupt controller with an IRQ line (typically - a GPIO) that will demultiplex and handle the interrupt from the single - interrupt line coming out of one of the SMI-based chips. It most - importantly provides link up/down interrupts to the PHY blocks inside - the ASIC. - -Required properties of interrupt-controller: - -- interrupt: parent interrupt, see interrupt-controller/interrupts.txt -- interrupt-controller: see interrupt-controller/interrupts.txt -- #address-cells: should be <0> -- #interrupt-cells: should be <1> - -- mdio - - This defines the internal MDIO bus of the SMI device, mostly for the - purpose of being able to hook the interrupts to the right PHY and - the right PHY to the corresponding port. - -Required properties of mdio: - -- compatible: should be set to "realtek,smi-mdio" for all SMI devices - -See net/mdio.txt for additional MDIO bus properties. - -See net/dsa/dsa.txt for a list of additional required and optional properties -and subnodes of DSA switches. - -Examples: - -An example for the RTL8366RB: - -switch { - compatible = "realtek,rtl8366rb"; - /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ - mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - /* GPIO 15 provides the interrupt */ - interrupt-parent = <&gpio0>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - phy-handle = <&phy0>; - }; - port@1 { - reg = <1>; - label = "lan1"; - phy-handle = <&phy1>; - }; - port@2 { - reg = <2>; - label = "lan2"; - phy-handle = <&phy2>; - }; - port@3 { - reg = <3>; - label = "lan3"; - phy-handle = <&phy3>; - }; - port@4 { - reg = <4>; - label = "wan"; - phy-handle = <&phy4>; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio", "dsa-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - phy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - phy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - phy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - phy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - phy4: phy@4 { - reg = <4>; - interrupt-parent = <&switch_intc>; - interrupts = <12>; - }; - }; -}; - -An example for the RTL8365MB-VC: - -switch { - compatible = "realtek,rtl8365mb"; - mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "swp0"; - phy-handle = <ðphy0>; - }; - port@1 { - reg = <1>; - label = "swp1"; - phy-handle = <ðphy1>; - }; - port@2 { - reg = <2>; - label = "swp2"; - phy-handle = <ðphy2>; - }; - port@3 { - reg = <3>; - label = "swp3"; - phy-handle = <ðphy3>; - }; - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&fec1>; - phy-mode = "rgmii"; - tx-internal-delay-ps = <2000>; - rx-internal-delay-ps = <2000>; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - ethphy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - ethphy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - ethphy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml new file mode 100644 index 000000000000..8756060895a8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -0,0 +1,394 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek switches for unmanaged switches + +allOf: + - $ref: dsa.yaml# + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + Realtek advertises these chips as fast/gigabit switches or unmanaged + switches. They can be controlled using different interfaces, like SMI, + MDIO or SPI. + + The SMI "Simple Management Interface" is a two-wire protocol using + bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does + not use the MDIO protocol. This binding defines how to specify the + SMI-based Realtek devices. The realtek-smi driver is a platform driver + and it must be inserted inside a platform node. + + The MDIO-connected switches use MDIO protocol to access their registers. + The realtek-mdio driver is an MDIO driver and it must be inserted inside + an MDIO node. + +properties: + compatible: + enum: + - realtek,rtl8365mb + - realtek,rtl8366 + - realtek,rtl8366rb + - realtek,rtl8366s + - realtek,rtl8367 + - realtek,rtl8367b + - realtek,rtl8367rb + - realtek,rtl8367s + - realtek,rtl8368s + - realtek,rtl8369 + - realtek,rtl8370 + description: | + realtek,rtl8365mb: 4+1 ports + realtek,rtl8366: 5+1 ports + realtek,rtl8366rb: 5+1 ports + realtek,rtl8366s: 5+1 ports + realtek,rtl8367: + realtek,rtl8367b: + realtek,rtl8367rb: 5+2 ports + realtek,rtl8367s: 5+2 ports + realtek,rtl8368s: 8 ports + realtek,rtl8369: 8+1 ports + realtek,rtl8370: 8+2 ports + + mdc-gpios: + description: GPIO line for the MDC clock line. + maxItems: 1 + + mdio-gpios: + description: GPIO line for the MDIO data line. + maxItems: 1 + + reset-gpios: + description: GPIO to be used to reset the whole device + maxItems: 1 + + realtek,disable-leds: + type: boolean + description: | + if the LED drivers are not used in the hardware design, + this will disable them so they are not turned on + and wasting power. + + interrupt-controller: + type: object + description: | + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the Realtek switch chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + + properties: + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: + A single IRQ line from the switch, either active LOW or HIGH + + '#address-cells': + const: 0 + + '#interrupt-cells': + const: 1 + + required: + - interrupt-controller + - '#address-cells' + - '#interrupt-cells' + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + const: realtek,smi-mdio + +if: + required: + - reg + +then: + not: + required: + - mdc-gpios + - mdio-gpios + - mdio + + properties: + mdc-gpios: false + mdio-gpios: false + mdio: false + +else: + required: + - mdc-gpios + - mdio-gpios + - mdio + - reset-gpios + +required: + - compatible + + # - mdc-gpios + # - mdio-gpios + # - reset-gpios + # - mdio + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc1: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc1>; + interrupts = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc1>; + interrupts = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc1>; + interrupts = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc1>; + interrupts = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc1>; + interrupts = <12>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8365mb"; + mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + switch_intc2: interrupt-controller { + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "swp0"; + phy-handle = <ðphy0>; + }; + port@1 { + reg = <1>; + label = "swp1"; + phy-handle = <ðphy1>; + }; + port@2 { + reg = <2>; + label = "swp2"; + phy-handle = <ðphy2>; + }; + port@3 { + reg = <3>; + label = "swp3"; + phy-handle = <ðphy3>; + }; + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&fec1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc2>; + interrupts = <0>; + }; + ethphy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc2>; + interrupts = <1>; + }; + ethphy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc2>; + interrupts = <2>; + }; + ethphy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc2>; + interrupts = <3>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@29 { + compatible = "realtek,rtl8367s"; + reg = <29>; + + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + switch_intc3: interrupt-controller { + interrupt-parent = <&gpio0>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@7 { + reg = <7>; + ethernet = <ðernet>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt index 020337f3c05f..801efc7d6818 100644 --- a/Documentation/devicetree/bindings/net/fsl-fman.txt +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -388,14 +388,24 @@ PROPERTIES Value type: <prop-encoded-array> Definition: A standard property. -- bus-frequency +- clocks + Usage: optional + Value type: <phandle> + Definition: A reference to the input clock of the controller + from which the MDC frequency is derived. + +- clock-frequency Usage: optional Value type: <u32> - Definition: Specifies the external MDIO bus clock speed to - be used, if different from the standard 2.5 MHz. - This may be due to the standard speed being unsupported (e.g. - due to a hardware problem), or to advertise that all relevant - components in the system support a faster speed. + Definition: Specifies the external MDC frequency, in Hertz, to + be used. Requires that the input clock is specified in the + "clocks" property. See also: mdio.yaml. + +- suppress-preamble + Usage: optional + Value type: <boolean> + Definition: Disable generation of preamble bits. See also: + mdio.yaml. - interrupts Usage: required for external MDIO diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index 691f886cfc4a..2bf31572b08d 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -5,6 +5,7 @@ Required properties: "marvell,armada-370-neta" "marvell,armada-xp-neta" "marvell,armada-3700-neta" + "marvell,armada-ac5-neta" - reg: address and length of the register set for the device. - interrupts: interrupt for the device - phy: See ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/net/mctp-i2c-controller.yaml b/Documentation/devicetree/bindings/net/mctp-i2c-controller.yaml new file mode 100644 index 000000000000..afd11c9422fa --- /dev/null +++ b/Documentation/devicetree/bindings/net/mctp-i2c-controller.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mctp-i2c-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MCTP I2C transport binding + +maintainers: + - Matt Johnston <matt@codeconstruct.com.au> + +description: | + An mctp-i2c-controller defines a local MCTP endpoint on an I2C controller. + MCTP I2C is specified by DMTF DSP0237. + + An mctp-i2c-controller must be attached to an I2C adapter which supports + slave functionality. I2C busses (either directly or as subordinate mux + busses) are attached to the mctp-i2c-controller with a 'mctp-controller' + property on each used bus. Each mctp-controller I2C bus will be presented + to the host system as a separate MCTP I2C instance. + +properties: + compatible: + const: mctp-i2c-controller + + reg: + minimum: 0x40000000 + maximum: 0x4000007f + description: | + 7 bit I2C address of the local endpoint. + I2C_OWN_SLAVE_ADDRESS (1<<30) flag must be set. + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + // Basic case of a single I2C bus + #include <dt-bindings/i2c/i2c.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + mctp-controller; + + mctp@30 { + compatible = "mctp-i2c-controller"; + reg = <(0x30 | I2C_OWN_SLAVE_ADDRESS)>; + }; + }; + + - | + // Mux topology with multiple MCTP-handling busses under + // a single mctp-i2c-controller. + // i2c1 and i2c6 can have MCTP devices, i2c5 does not. + #include <dt-bindings/i2c/i2c.h> + + i2c1: i2c { + #address-cells = <1>; + #size-cells = <0>; + mctp-controller; + + mctp@50 { + compatible = "mctp-i2c-controller"; + reg = <(0x50 | I2C_OWN_SLAVE_ADDRESS)>; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + i2c-parent = <&i2c1>; + + i2c5: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@33 { + reg = <0x33>; + }; + }; + + i2c6: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + mctp-controller; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt deleted file mode 100644 index afbcaebf062e..000000000000 --- a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt +++ /dev/null @@ -1,91 +0,0 @@ -MediaTek DWMAC glue layer controller - -This file documents platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC -- reg: Address and length of the register set for the device -- interrupts: Should contain the MAC interrupts -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: The name of the clock listed in the clocks property. These are - "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC. -- mac-address: See ethernet.txt in the same directory -- phy-mode: See ethernet.txt in the same directory -- mediatek,pericfg: A phandle to the syscon node that control ethernet - interface and timing delay. - -Optional properties: -- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface when the reference clock is from MT2712 SoC. -- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. - It should be defined for RGMII/MII interface. - It should be defined for RMII interface. -Both delay properties need to be a multiple of 170 for RGMII interface, -or will round down. Range 0~31*170. -Both delay properties need to be a multiple of 550 for MII/RMII interface, -or will round down. Range 0~31*550. - -- mediatek,rmii-rxc: boolean property, if present indicates that the RMII - reference clock, which is from external PHYs, is connected to RXC pin - on MT2712 SoC. - Otherwise, is connected to TXC pin. -- mediatek,rmii-clk-from-mac: boolean property, if present indicates that - MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only. -- mediatek,txc-inverse: boolean property, if present indicates that - 1. tx clock will be inversed in MII/RGMII case, - 2. tx clock inside MAC will be inversed relative to reference clock - which is from external PHYs in RMII case, and it rarely happen. - 3. the reference clock, which outputs to TXC pin will be inversed in RMII case - when the reference clock is from MT2712 SoC. -- mediatek,rxc-inverse: boolean property, if present indicates that - 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMII case, when - the reference clock is from external PHYs. - 3. the inside clock, which be sent to MAC, will be inversed in RMII case when - the reference clock is from MT2712 SoC. -- assigned-clocks: mac_main and ptp_ref clocks -- assigned-clock-parents: parent clocks of the assigned clocks - -Example: - eth: ethernet@1101c000 { - compatible = "mediatek,mt2712-gmac"; - reg = <0 0x1101c000 0 0x1300>; - interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "macirq"; - phy-mode ="rgmii-rxid"; - mac-address = [00 55 7b b5 7d f7]; - clock-names = "axi", - "apb", - "mac_main", - "ptp_ref", - "rmii_internal"; - clocks = <&pericfg CLK_PERI_GMAC>, - <&pericfg CLK_PERI_GMAC_PCLK>, - <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>, - <&topckgen CLK_TOP_ETHERPLL_50M>; - power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; - mediatek,pericfg = <&pericfg>; - mediatek,tx-delay-ps = <1530>; - mediatek,rx-delay-ps = <1530>; - mediatek,rmii-rxc; - mediatek,txc-inverse; - mediatek,rxc-inverse; - snps,txpbl = <1>; - snps,rxpbl = <1>; - snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; - snps,reset-active-low; - }; diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml new file mode 100644 index 000000000000..901944683322 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek DWMAC glue layer controller + +maintainers: + - Biao Huang <biao.huang@mediatek.com> + +description: + This file documents platform glue layer for stmmac. + +# We need a select here so we don't match all nodes with 'snps,dwmac' +select: + properties: + compatible: + contains: + enum: + - mediatek,mt2712-gmac + - mediatek,mt8195-gmac + required: + - compatible + +allOf: + - $ref: "snps,dwmac.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - mediatek,mt2712-gmac + - const: snps,dwmac-4.20a + - items: + - enum: + - mediatek,mt8195-gmac + - const: snps,dwmac-5.10a + + clocks: + minItems: 5 + items: + - description: AXI clock + - description: APB clock + - description: MAC Main clock + - description: PTP clock + - description: RMII reference clock provided by MAC + - description: MAC clock gate + + clock-names: + minItems: 5 + items: + - const: axi + - const: apb + - const: mac_main + - const: ptp_ref + - const: rmii_internal + - const: mac_cg + + mediatek,pericfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle to the syscon node that control ethernet + interface and timing delay. + + mediatek,tx-delay-ps: + description: + The internal TX clock delay (provided by this driver) in nanoseconds. + For MT2712 RGMII interface, Allowed value need to be a multiple of 170, + or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, + or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, + or will round down. Range 0~31*290. + + mediatek,rx-delay-ps: + description: + The internal RX clock delay (provided by this driver) in nanoseconds. + For MT2712 RGMII interface, Allowed value need to be a multiple of 170, + or will round down. Range 0~31*170. + For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, + or will round down. Range 0~31*550. + For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple + of 290, or will round down. Range 0~31*290. + + mediatek,rmii-rxc: + type: boolean + description: + If present, indicates that the RMII reference clock, which is from external + PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin. + + mediatek,rmii-clk-from-mac: + type: boolean + description: + If present, indicates that MAC provides the RMII reference clock, which + outputs to TXC pin only. + + mediatek,txc-inverse: + type: boolean + description: + If present, indicates that + 1. tx clock will be inversed in MII/RGMII case, + 2. tx clock inside MAC will be inversed relative to reference clock + which is from external PHYs in RMII case, and it rarely happen. + 3. the reference clock, which outputs to TXC pin will be inversed in RMII case + when the reference clock is from MAC. + + mediatek,rxc-inverse: + type: boolean + description: + If present, indicates that + 1. rx clock will be inversed in MII/RGMII case. + 2. reference clock will be inversed when arrived at MAC in RMII case, when + the reference clock is from external PHYs. + 3. the inside clock, which be sent to MAC, will be inversed in RMII case when + the reference clock is from MAC. + + mediatek,mac-wol: + type: boolean + description: + If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled. + Otherwise, PHY WOL is perferred. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - phy-mode + - mediatek,pericfg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2712-clk.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/mt2712-power.h> + + eth: ethernet@1101c000 { + compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a"; + reg = <0x1101c000 0x1300>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "macirq"; + phy-mode ="rgmii-rxid"; + mac-address = [00 55 7b b5 7d f7]; + clock-names = "axi", + "apb", + "mac_main", + "ptp_ref", + "rmii_internal"; + clocks = <&pericfg CLK_PERI_GMAC>, + <&pericfg CLK_PERI_GMAC_PCLK>, + <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; + mediatek,pericfg = <&pericfg>; + mediatek,tx-delay-ps = <1530>; + snps,txpbl = <1>; + snps,rxpbl = <1>; + snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <0 10000 10000>; + }; diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt index 8d157f0295a5..c5ab62c39133 100644 --- a/Documentation/devicetree/bindings/net/micrel.txt +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -45,3 +45,20 @@ Optional properties: In fiber mode, auto-negotiation is disabled and the PHY can only work in 100base-fx (full and half duplex) modes. + + - lan8814,ignore-ts: If present the PHY will not support timestamping. + + This option acts as check whether Timestamping is supported by + hardware or not. LAN8814 phy support hardware tmestamping. + + - lan8814,latency_rx_10: Configures Latency value of phy in ingress at 10 Mbps. + + - lan8814,latency_tx_10: Configures Latency value of phy in egress at 10 Mbps. + + - lan8814,latency_rx_100: Configures Latency value of phy in ingress at 100 Mbps. + + - lan8814,latency_tx_100: Configures Latency value of phy in egress at 100 Mbps. + + - lan8814,latency_rx_1000: Configures Latency value of phy in ingress at 1000 Mbps. + + - lan8814,latency_tx_1000: Configures Latency value of phy in egress at 1000 Mbps. diff --git a/Documentation/devicetree/bindings/net/microchip,lan966x-switch.yaml b/Documentation/devicetree/bindings/net/microchip,lan966x-switch.yaml index e79e4e166ad8..13812768b923 100644 --- a/Documentation/devicetree/bindings/net/microchip,lan966x-switch.yaml +++ b/Documentation/devicetree/bindings/net/microchip,lan966x-switch.yaml @@ -38,6 +38,7 @@ properties: - description: register based extraction - description: frame dma based extraction - description: analyzer interrupt + - description: ptp interrupt interrupt-names: minItems: 1 @@ -45,6 +46,7 @@ properties: - const: xtr - const: fdma - const: ana + - const: ptp resets: items: diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml index 347b912a46bb..6c86d3d85e99 100644 --- a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml +++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml @@ -53,12 +53,14 @@ properties: items: - description: register based extraction - description: frame dma based extraction + - description: ptp interrupt interrupt-names: minItems: 1 items: - const: xtr - const: fdma + - const: ptp resets: items: diff --git a/Documentation/devicetree/bindings/net/mscc-miim.txt b/Documentation/devicetree/bindings/net/mscc-miim.txt index 7104679cf59d..70e0cb1ee485 100644 --- a/Documentation/devicetree/bindings/net/mscc-miim.txt +++ b/Documentation/devicetree/bindings/net/mscc-miim.txt @@ -2,7 +2,7 @@ Microsemi MII Management Controller (MIIM) / MDIO ================================================= Properties: -- compatible: must be "mscc,ocelot-miim" +- compatible: must be "mscc,ocelot-miim" or "microchip,lan966x-miim" - reg: The base address of the MDIO bus controller register bank. Optionally, a second register bank can be defined if there is an associated reset register for internal PHYs diff --git a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml index bda821065a2b..ee2ccacc39ff 100644 --- a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml +++ b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml @@ -45,8 +45,10 @@ properties: - items: - enum: + - renesas,r9a07g043-gbeth # RZ/G2UL - renesas,r9a07g044-gbeth # RZ/G2{L,LC} - - const: renesas,rzg2l-gbeth # RZ/G2L + - renesas,r9a07g054-gbeth # RZ/V2L + - const: renesas,rzg2l-gbeth # RZ/{G2L,G2UL,V2L} family reg: true diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml index 269cd63fb544..3216c999f0e1 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml @@ -18,7 +18,7 @@ description: | wireless device. The node is expected to be specified as a child node of the PCI controller to which the wireless chip is connected. Alternatively, it can specify the wireless part of the MT7628/MT7688 - or MT7622 SoC. + or MT7622/MT7986 SoC. allOf: - $ref: ieee80211.yaml# @@ -29,9 +29,13 @@ properties: - mediatek,mt76 - mediatek,mt7628-wmac - mediatek,mt7622-wmac + - mediatek,mt7986-wmac reg: - maxItems: 1 + minItems: 1 + maxItems: 3 + description: + MT7986 should contain 3 regions consys, dcm, and sku, in this order. interrupts: maxItems: 1 @@ -39,6 +43,17 @@ properties: power-domains: maxItems: 1 + memory-region: + maxItems: 1 + + resets: + maxItems: 1 + description: + Specify the consys reset for mt7986. + + reset-name: + const: consys + mediatek,infracfg: $ref: /schemas/types.yaml#/definitions/phandle description: @@ -69,6 +84,15 @@ properties: calibration data is generic and specific calibration data should be pulled from the OTP ROM + mediatek,disable-radar-background: + type: boolean + description: + Disable/enable radar/CAC detection running on a dedicated offchannel + chain available on some hw. + Background radar/CAC detection allows to avoid the CAC downtime + switching on a different channel during CAC detection on the selected + radar channel. + led: type: object $ref: /schemas/leds/common.yaml# @@ -165,7 +189,7 @@ required: - compatible - reg -additionalProperties: false +unevaluatedProperties: false examples: - | @@ -231,3 +255,15 @@ examples: power-domains = <&scpsys 3>; }; + + - | + wifi@18000000 { + compatible = "mediatek,mt7986-wmac"; + resets = <&watchdog 23>; + reset-names = "consys"; + reg = <0x18000000 0x1000000>, + <0x10003000 0x1000>, + <0x11d10000 0x1000>; + interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; + memory-region = <&wmcpu_emi>; + }; diff --git a/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml b/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml new file mode 100644 index 000000000000..4d91e2f4f247 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,lynx-28g.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Lynx 28G SerDes PHY binding + +maintainers: + - Ioana Ciornei <ioana.ciornei@nxp.com> + +properties: + compatible: + enum: + - fsl,lynx-28g + + reg: + maxItems: 1 + + "#phy-cells": + const: 1 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + soc { + #address-cells = <2>; + #size-cells = <2>; + serdes_1: phy@1ea0000 { + compatible = "fsl,lynx-28g"; + reg = <0x0 0x1ea0000 0x0 0x1e30>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml b/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml new file mode 100644 index 000000000000..51492fe738ec --- /dev/null +++ b/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/transmit-amplitude.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common PHY and network PCS transmit amplitude property binding + +description: + Binding describing the peak-to-peak transmit amplitude for common PHYs + and network PCSes. + +maintainers: + - Marek Behún <kabel@kernel.org> + +properties: + tx-p2p-microvolt: + description: + Transmit amplitude voltages in microvolts, peak-to-peak. If this property + contains multiple values for various PHY modes, the + 'tx-p2p-microvolt-names' property must be provided and contain + corresponding mode names. + + tx-p2p-microvolt-names: + description: | + Names of the modes corresponding to voltages in the 'tx-p2p-microvolt' + property. Required only if multiple voltages are provided. + + If a value of 'default' is provided, the system should use it for any PHY + mode that is otherwise not defined here. If 'default' is not provided, the + system should use manufacturer default value. + minItems: 1 + maxItems: 16 + items: + enum: + - default + + # ethernet modes + - sgmii + - qsgmii + - xgmii + - 1000base-x + - 2500base-x + - 5gbase-r + - rxaui + - xaui + - 10gbase-kr + - usxgmii + - 10gbase-r + - 25gbase-r + + # PCIe modes + - pcie + - pcie1 + - pcie2 + - pcie3 + - pcie4 + - pcie5 + - pcie6 + + # USB modes + - usb + - usb-ls + - usb-fs + - usb-hs + - usb-ss + - usb-ss+ + - usb-4 + + # storage modes + - sata + - ufs-hs + - ufs-hs-a + - ufs-hs-b + + # display modes + - lvds + - dp + - dp-rbr + - dp-hbr + - dp-hbr2 + - dp-hbr3 + - dp-uhbr-10 + - dp-uhbr-13.5 + - dp-uhbr-20 + + # camera modes + - mipi-dphy + - mipi-dphy-univ + - mipi-dphy-v2.5-univ + +dependencies: + tx-p2p-microvolt-names: [ tx-p2p-microvolt ] + +additionalProperties: true + +examples: + - | + phy: phy { + #phy-cells = <1>; + tx-p2p-microvolt = <915000>, <1100000>, <1200000>; + tx-p2p-microvolt-names = "2500base-x", "usb-hs", "usb-ss"; + }; |