diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
36 files changed, 518 insertions, 71 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt index ddfade40ac59..7803e77d85cb 100644 --- a/Documentation/devicetree/bindings/arm/gic-v3.txt +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs. These nodes must have the following properties: - compatible : Should at least contain "arm,gic-v3-its". - msi-controller : Boolean property. Identifies the node as an MSI controller +- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device + which will generate the MSI. - reg: Specifies the base physical address and size of the ITS registers. @@ -83,6 +85,7 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; }; @@ -107,12 +110,14 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; gic-its@2c400000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c400000 0 0x200000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index a8274eabae2e..b8e41c148a3c 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -497,7 +497,7 @@ cpus { }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_RETENTION_0_0: cpu-retention-0-0 { compatible = "arm,idle-state"; diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78edb80002c8..78e2a31c58d0 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -5,6 +5,8 @@ The follow error types are supported: memory controller - Memory controller PMD (L1/L2) - Processor module unit (PMD) L1/L2 cache + L3 - L3 cache controller + SoC - SoC IP's such as Ethernet, SATA, and etc The following section describes the EDAC DT node binding. @@ -30,6 +32,17 @@ Required properties for PMD subnode: - reg : First resource shall be the PMD resource. - pmd-controller : Instance number of the PMD controller. +Required properties for L3 subnode: +- compatible : Shall be "apm,xgene-edac-l3" or + "apm,xgene-edac-l3-v2". +- reg : First resource shall be the L3 EDAC resource. + +Required properties for SoC subnode: +- compatible : Shall be "apm,xgene-edac-soc-v1" for revision 1 or + "apm,xgene-edac-l3-soc" for general value reporting + only. +- reg : First resource shall be the SoC EDAC resource. + Example: csw: csw@7e200000 { compatible = "apm,xgene-csw", "syscon"; @@ -76,4 +89,14 @@ Example: reg = <0x0 0x7c000000 0x0 0x200000>; pmd-controller = <0>; }; + + edacl3@7e600000 { + compatible = "apm,xgene-edac-l3"; + reg = <0x0 0x7e600000 0x0 0x1000>; + }; + + edacsoc@7e930000 { + compatible = "apm,xgene-edac-soc-v1"; + reg = <0x0 0x7e930000 0x0 0x1000>; + }; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/Documentation/devicetree/bindings/gpio/gpio-msm.txt deleted file mode 100644 index ac20e68a004e..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-msm.txt +++ /dev/null @@ -1,26 +0,0 @@ -MSM GPIO controller bindings - -Required properties: -- compatible: - - "qcom,msm-gpio" for MSM controllers -- #gpio-cells : Should be two. - - first cell is the pin number - - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. -- #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller -- interrupts : Specify the TLMM summary interrupt number -- ngpio : Specify the number of MSM GPIOs - -Example: - - msmgpio: gpio@fd510000 { - compatible = "qcom,msm-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; - interrupts = <0 208 0>; - ngpio = <150>; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index b9a42f294dd0..13df9933f4cd 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -24,6 +24,7 @@ Required properties: ti,tca6408 ti,tca6416 ti,tca6424 + ti,tca9539 exar,xra1202 Example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt index db4c6a663c03..7b542657f259 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -12,6 +12,13 @@ Required properties: - interrupts : Interrupt specifier (see interrupt bindings for details) - interrupt-parent : Must be core interrupt controller +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. - reg : Address and length of the register set for the device Example: @@ -22,5 +29,7 @@ Example: gpio-controller; interrupt-parent = <&intc>; interrupts = <0 20 4>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0xe000a000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 5788d5cf1252..069cdf6f9dac 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -16,7 +16,9 @@ properties, each containing a 'gpio-list': GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed -for new bindings. +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. GPIO properties can contain one or more GPIO phandles, but only in exceptional cases should they contain more than one. If your device uses several GPIOs with @@ -52,9 +54,13 @@ only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. + Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. Use the macros -defined in include/dt-bindings/gpio/gpio.h whenever possible: +be documented in the device tree binding for the device. + +Most controllers are however specifying a generic flag bitfield +in the last cell, so for these, use the macros defined in +include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -65,6 +71,15 @@ Example of a node using GPIOs: GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. +Optional standard bitfield specifiers for the last cell: + +- Bit 0: 0 means active high, 1 means active low +- Bit 1: 1 means single-ended wiring, see: + https://en.wikipedia.org/wiki/Single-ended_triode + When used with active-low, this means open drain/collector, see: + https://en.wikipedia.org/wiki/Open_collector + When used with active-high, this means open source/emitter + 1.1) GPIO specifier best practices ---------------------------------- @@ -116,6 +131,30 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Optionally, a GPIO controller may have a "ngpios" property. This property +indicates the number of in-use slots of available slots for GPIOs. The +typical example is something like this: the hardware register is 32 bits +wide, but only 18 of the bits have a physical counterpart. The driver is +generally written so that all 32 bits can be used, but the IP block is reused +in a lot of designs, some using all 32 bits, some using 18 and some using +12. In this case, setting "ngpios = <18>;" informs the driver that only the +first 18 GPIOs, at local offset 0 .. 17, are in use. + +If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an +additional bitmask is needed to specify which GPIOs are actually in use, +and which are dummies. The bindings for this case has not yet been +specified, but should be specified if/when such hardware appears. + +Example: + +gpio-controller@00000000 { + compatible = "foo"; + reg = <0x00000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <18>; +} + The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism providing automatic GPIO request and configuration as part of the gpio-controller's driver probe function. diff --git a/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt new file mode 100644 index 000000000000..50ec2e690701 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt @@ -0,0 +1,22 @@ +Binding for the GPIO extension bus found on some LaCie/Seagate boards +(Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-gpio-ext". +- addr-gpios: GPIOs representing the address register (LSB -> MSB). +- data-gpios: GPIOs representing the data register (LSB -> MSB). +- enable-gpio: latches the new configuration (address, data) on raising edge. + +Example: + +netxbig_gpio_ext: netxbig-gpio-ext { + compatible = "lacie,netxbig-gpio-ext"; + + addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH + &gpio1 16 GPIO_ACTIVE_HIGH + &gpio1 17 GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH + &gpio1 14 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt index c5933573e0f6..4a3679d54457 100644 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -1,10 +1,11 @@ -* Bosch BMA180 triaxial acceleration sensor +* Bosch BMA180 / BMA250 triaxial acceleration sensor http://omapworld.com/BMA180_111_1002839.pdf +http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf Required properties: - - compatible : should be "bosch,bma180" + - compatible : should be "bosch,bma180" or "bosch,bma250" - reg : the I2C address of the sensor Optional properties: @@ -13,6 +14,9 @@ Optional properties: - interrupts : interrupt mapping for GPIO IRQ, it should by configured with flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + For the bma250 the first interrupt listed must be the one + connected to the INT1 pin, the second (optional) interrupt + listed must be the one connected to the INT2 pin. Example: diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt index 635a3b036630..8d91ba9ff2fd 100644 --- a/Documentation/devicetree/bindings/input/cypress,cyapa.txt +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -25,7 +25,7 @@ Example: /* Cypress Gen3 touchpad */ touchpad@67 { compatible = "cypress,cyapa"; - reg = <0x24>; + reg = <0x67>; interrupt-parent = <&gpio>; interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ wakeup-source; diff --git a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt index 391717a68f3b..ec96b1f01478 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt @@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority interrupt. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" - as fallback +- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or + "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc" - reg: Base address and size of the controllers memory area - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Interrupt specifier for the controllers interrupt. @@ -13,6 +13,9 @@ Required Properties: - #interrupt-cells : Specifies the number of cells needed to encode interrupt source, should be 1 +Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x, +use ar7240 for all other SoCs. + Please refer to interrupts.txt in this directory for details of the common Interrupt Controllers bindings used by client devices. @@ -28,3 +31,16 @@ Example: interrupt-controller; #interrupt-cells = <1>; }; + +Another example: + + interrupt-controller@18060010 { + compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc"; + reg = <0x18060010 0x4>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt index c05ed91a4e42..85c0c58617f6 100644 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -27,9 +27,9 @@ Required properties of the LED child node: - flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt Maximum flash LED supply current can be calculated using following formula: I = 1A * 162kohm / Rset. -- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt - Maximum flash timeout can be calculated using following - formula: T = 8.82 * 10^9 * Ct. +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Maximum flash timeout can be calculated using following + formula: T = 8.82 * 10^9 * Ct. Optional properties of the LED child node: - label : see Documentation/devicetree/bindings/leds/common.txt @@ -54,7 +54,7 @@ aat1290 { label = "aat1290-flash"; led-max-microamp = <520833>; flash-max-microamp = <1012500>; - flash-timeout-us = <1940000>; + flash-max-timeout-us = <1940000>; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index f9e36adc0ebf..3f48c1eaf085 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -29,6 +29,14 @@ Required properties: Optional properties: - brcm,serial-leds : Boolean, enables Serial LEDs. Default : false + - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing. + Default : false + - brcm,serial-clk-low : Boolean, makes clock signal active low. + Default : false + - brcm,serial-dat-low : Boolean, makes data signal active low. + Default : false + - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction. + Default : false Each LED is represented as a sub-node of the brcm,bcm6328-leds device. @@ -110,6 +118,8 @@ Scenario 2 : BCM63268 with Serial/GPHY0 LEDs #size-cells = <0>; reg = <0x10001900 0x24>; brcm,serial-leds; + brcm,serial-dat-low; + brcm,serial-shift-inv; gphy0_spd0@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/leds/leds-netxbig.txt b/Documentation/devicetree/bindings/leds/leds-netxbig.txt new file mode 100644 index 000000000000..5ef92a26d768 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-netxbig.txt @@ -0,0 +1,92 @@ +Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate +boards (Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-leds". +- gpio-ext: Phandle for the gpio-ext bus. + +Optional properties: +- timers: Timer array. Each timer entry is represented by three integers: + Mode (gpio-ext bus), delay_on and delay_off. + +Each LED is represented as a sub-node of the netxbig-leds device. + +Required sub-node properties: +- mode-addr: Mode register address on gpio-ext bus. +- mode-val: Mode to value mapping. Each entry is represented by two integers: + A mode and the corresponding value on the gpio-ext bus. +- bright-addr: Brightness register address on gpio-ext bus. +- max-brightness: Maximum brightness value. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +netxbig-leds { + compatible = "lacie,netxbig-leds"; + + gpio-ext = &gpio_ext; + + timers = <NETXBIG_LED_TIMER1 500 500 + NETXBIG_LED_TIMER2 500 1000>; + + blue-power { + label = "netxbig:blue:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 1 + NETXBIG_LED_TIMER1 3 + NETXBIG_LED_TIMER2 7>; + bright-addr = <1>; + max-brightness = <7>; + }; + red-power { + label = "netxbig:red:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <1>; + max-brightness = <7>; + }; + blue-sata0 { + label = "netxbig:blue:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata0 { + label = "netxbig:red:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; + blue-sata1 { + label = "netxbig:blue:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata1 { + label = "netxbig:red:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index b7943f3f9995..dedfb02c744a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -22,6 +22,8 @@ Optional properties: - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. + - little-endian : If the host controller is little-endian mode, specify + this property. The default endian mode is big-endian. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 0384fc3f64e8..f693baf87264 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -37,6 +37,7 @@ Optional properties: - sd-uhs-sdr104: SD UHS SDR104 speed is supported - sd-uhs-ddr50: SD UHS DDR50 speed is supported - cap-power-off-card: powering off the card is safe +- cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index a1adfa495ad3..0120c7f1109c 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -17,6 +17,11 @@ Required properties: - vmmc-supply: power to the Core - vqmmc-supply: power to the IO +Optional properties: +- assigned-clocks: PLL of the source clock +- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock +- hs400-ds-delay: HS400 DS delay setting + Examples: mmc0: mmc@11230000 { compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc"; @@ -24,9 +29,13 @@ mmc0: mmc@11230000 { interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; vmmc-supply = <&mt6397_vemc_3v3_reg>; vqmmc-supply = <&mt6397_vio18_reg>; - clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; clock-names = "source", "hclk"; pinctrl-names = "default", "state_uhs"; pinctrl-0 = <&mmc0_pins_default>; pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index d38942f6c5ae..cae29eb5733d 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -6,11 +6,12 @@ and the properties used by the MMCIF device. Required properties: -- compatible: must contain one of the following +- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a + fallback. Examples with <soctype> are: - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - - "renesas,sh-mmcif" for the generic MMCIF + - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c327c2d6f23d..3dc13b68fc3f 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -14,6 +14,19 @@ Required Properties: before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 +Optional Properties: +* clocks: from common clock binding: if ciu_drive and ciu_sample are + specified in clock-names, should contain handles to these clocks. + +* clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt + two more clocks "ciu-drive" and "ciu-sample" are supported. They are used + to control the clock phases, "ciu-sample" is required for tuning high- + speed modes. + +* rockchip,default-sample-phase: The default phase to set ciu_sample at + probing, low speeds or in case where all phases work at tuning time. + If not specified 0 deg will be used. + Example: rkdwmmc0@12200000 { diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 346c6095a615..8636f5ae97e5 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -75,6 +75,12 @@ Optional properties: * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. +* dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. Refer to dma.txt for details. + +* dma-names: request names for generic DMA client binding. Must be "rx-tx". + Refer to dma.txt for details. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -95,6 +101,23 @@ board specific portions as listed below. #size-cells = <0>; }; +[board specific internal DMA resources] + + dwmmc0@12200000 { + clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; + num-slots = <1>; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + vmmc-supply = <&buck8>; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + +[board specific generic DMA request binding] + dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; @@ -106,4 +129,6 @@ board specific portions as listed below. bus-width = <8>; cap-mmc-highspeed; cap-sd-highspeed; + dmas = <&pdma 12>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index a9df21aaa154..a2cae4eb4a60 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -39,6 +39,7 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy-handle : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt new file mode 100644 index 000000000000..974edd5c85cc --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -0,0 +1,24 @@ +SMSC LAN87xx Ethernet PHY + +Some boards require special tuning values. Configure them +through an Ethernet OF device node. + +Optional properties: + +- smsc,disable-energy-detect: + If set, do not enable energy detect mode for the SMSC phy. + default: enable energy detect mode + +Examples: +smsc phy with disabled energy detect mode on an am335x based board. +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index d8ef5bf50f11..7fab84b33531 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -7,7 +7,8 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; - "renesas,pci-r8a7791" for the R8A7791 SoC. + "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7794" for the R8A7794 SoC. - reg: A list of physical regions to access the device: the first is the operational registers for the OHCI/EHCI controllers and the second is for the bridge configuration and control registers. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 3c821cda1ad0..b321b26780dc 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -17,6 +17,7 @@ Required properties: "allwinner,sun8i-a23-pinctrl" "allwinner,sun8i-a23-r-pinctrl" "allwinner,sun8i-a33-pinctrl" + "allwinner,sun8i-a83t-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt new file mode 100644 index 000000000000..61ac75706cc9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt @@ -0,0 +1,90 @@ +* Atmel PIO4 Controller + +The Atmel PIO4 controller is used to select the function of a pin and to +configure it. + +Required properties: +- compatible: "atmel,sama5d2-pinctrl". +- reg: base address and length of the PIO controller. +- interrupts: interrupt outputs from the controller, one for each bank. +- interrupt-controller: mark the device node as an interrupt controller. +- #interrupt-cells: should be two. +- gpio-controller: mark the device node as a gpio controller. +- #gpio-cells: should be two. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +Subnode format +Each node (or subnode) will list the pins it needs and how to configured these +pins. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array. Each integer represents a pin number plus mux and +ioset settings. Use the macros from boot/dts/<soc>-pinfunc.h file to get the +right representation of the pin. + +Optional properties: +- GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable, +bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable, +input-debounce, output-low, output-high. + +Example: + +#include <sama5d2-pinfunc.h> + +... +{ + pioA: pinctrl@fc038000 { + compatible = "atmel,sama5d2-pinctrl"; + reg = <0xfc038000 0x600>; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>, + <68 IRQ_TYPE_LEVEL_HIGH 7>, + <69 IRQ_TYPE_LEVEL_HIGH 7>, + <70 IRQ_TYPE_LEVEL_HIGH 7>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&pioA_clk>; + + pinctrl_i2c0_default: i2c0_default { + pinmux = <PIN_PD21__TWD0>, + <PIN_PD22__TWCK0>; + bias-disable; + }; + + pinctrl_led_gpio_default: led_gpio_default { + pinmux = <PIN_PB0>, + <PIN_PB5>; + bias-pull-up; + }; + + pinctrl_sdmmc1_default: sdmmc1_default { + cmd_data { + pinmux = <PIN_PA28__SDMMC1_CMD>, + <PIN_PA18__SDMMC1_DAT0>, + <PIN_PA19__SDMMC1_DAT1>, + <PIN_PA20__SDMMC1_DAT2>, + <PIN_PA21__SDMMC1_DAT3>; + bias-pull-up; + }; + + ck_cd { + pinmux = <PIN_PA22__SDMMC1_CK>, + <PIN_PA30__SDMMC1_CD>; + bias-disable; + }; + }; + ... + }; +}; +... diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt index a8bb5e26019c..f8fa28ce163e 100644 --- a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt @@ -20,7 +20,10 @@ Required properties: "marvell,berlin2cd-soc-pinctrl", "marvell,berlin2cd-system-pinctrl", "marvell,berlin2q-soc-pinctrl", - "marvell,berlin2q-system-pinctrl" + "marvell,berlin2q-system-pinctrl", + "marvell,berlin4ct-avio-pinctrl", + "marvell,berlin4ct-soc-pinctrl", + "marvell,berlin4ct-system-pinctrl" Required subnode-properties: - groups: a list of strings describing the group names. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt index 6540ca56be5e..16589fb6f420 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt @@ -3,8 +3,8 @@ Broadcom Cygnus GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or - "brcm,cygnus-crmu-gpio" + Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", + "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" - reg: Define the base and range of the I/O address space that contains the Cygnus @@ -26,9 +26,13 @@ Optional properties: - interrupt-controller: Specifies that the node is an interrupt controller -- pinmux: - Specifies the phandle to the IOMUX device, where pins can be individually -muxed to GPIO +- gpio-ranges: + Specifies the mapping between gpio controller and pin-controllers pins. + This requires 4 fields in cells defined as - + 1. Phandle of pin-controller. + 2. GPIO base pin offset. + 3 Pin-control base pin offset. + 4. number of gpio pins which are linearly mapped from pin base. Supported generic PINCONF properties in child nodes: @@ -78,6 +82,8 @@ Example: gpio-controller; interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; + gpio-ranges = <&pinctrl 0 42 1>, + <&pinctrl 1 44 3>; }; /* diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 8bbf25d58656..457b2c68d47b 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -1,16 +1,42 @@ * Freescale i.MX7 Dual IOMUX Controller +iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar +as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low +power state retention capabilities on gpios that are part of iomuxc-lpsr +(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for +mux and pad control settings, it shares the input select register from main +iomuxc controller for daisy chain settings, the fsl,input-sel property extends +fsl,imx-pinctrl driver to support iomuxc-lpsr controller. + +iomuxc_lpsr: iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; +}; + +iomuxc: iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; +}; + +Pheriparials using pads from iomuxc-lpsr support low state retention power +state, under LPSR mode GPIO's state of pads are retain. + Please refer to fsl,imx-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "fsl,imx7d-iomuxc" +- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or + "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller. - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual Reference Manual for detailed CONFIG settings. +- fsl,input-sel: required property for iomuxc-lpsr controller, this property is + a phandle for main iomuxc controller which shares the input select register for + daisy chain settings. CONFIG bits definition: PAD_CTL_PUS_100K_DOWN (0 << 5) @@ -25,3 +51,38 @@ PAD_CTL_DSE_X1 (0 << 0) PAD_CTL_DSE_X2 (1 << 0) PAD_CTL_DSE_X3 (2 << 0) PAD_CTL_DSE_X4 (3 << 0) + +Examples: +While iomuxc-lpsr is intended to be used by dedicated peripherals to take +advantages of LPSR power mode, is also possible that an IP to use pads from +any of the iomux controllers. For example the I2C1 IP can use SCL pad from +iomuxc-lpsr controller and SDA pad from iomuxc controller as: + +i2c1: i2c@30a20000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>; + status = "okay"; +}; + +iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + + pinctrl_i2c1_1: i2c1grp-1 { + fsl,pins = < + MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f + >; + }; +}; + +iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; + + pinctrl_i2c1_2: i2c1grp-2 { + fsl,pins = < + MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f + >; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 9496934528bd..ffadb7a371f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -19,6 +19,7 @@ Required Properties: - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. + - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt index 32aa26f1e434..acbcb452a69a 100644 --- a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. Required properties: - compatible: - - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. + - should be "ti,pbias-dra7" for DRA7 + - should be "ti,pbias-omap2" for OMAP2 + - should be "ti,pbias-omap3" for OMAP3 + - should be "ti,pbias-omap4" for OMAP4 + - should be "ti,pbias-omap5" for OMAP5 + - "ti,pbias-omap" is deprecated - reg: pbias register offset from syscon base and size of pbias register. - syscon : phandle of the system control module - regulator-name : should be diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 8f771441be60..705075da2f10 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -51,7 +51,7 @@ Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words (default is 64) - renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64, or 256 on R-Car Gen2) + (default is 64) Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index dcefc438272f..6160ffbcb3d3 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -15,17 +15,18 @@ Required properties: - interrupts: Should contain spi interrupt - clocks: phandles to input clocks. - The first should be <&topckgen CLK_TOP_SPI_SEL>. - The second should be one of the following. + The first should be one of the following. It's PLL. - <&clk26m>: specify parent clock 26MHZ. - <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ. It's the default one. - <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ. - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux. + The third is <&pericfg CLK_PERI_SPI0>. It's clock gate. -- clock-names: shall be "spi-clk" for the controller clock, and - "parent-clk" for the parent clock. +- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the + muxes clock, and "spi-clk" for the clock gate. Optional properties: - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi @@ -44,8 +45,11 @@ spi: spi@1100a000 { #size-cells = <0>; reg = <0 0x1100a000 0 0x1000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>; - clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>; - clock-names = "spi-clk", "parent-clk"; + clocks = <&topckgen CLK_TOP_SYSPLL3_D2>, + <&topckgen CLK_TOP_SPI_SEL>, + <&pericfg CLK_PERI_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + mediatek,pad-select = <0>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 8a49362dea6e..41b817f7b670 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to be the cooling-min-state and cooling-max-state +(as referred to by the cooling-min-level and cooling-max-level properties) should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: -- cooling-min-state: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-state: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order Size: one cell to specify minimum and maximum cooling state used @@ -77,6 +69,15 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. +Optional properties: +- cooling-min-level: An integer indicating the smallest + Type: unsigned cooling state accepted. Typically 0. + Size: one cell + +- cooling-max-level: An integer indicating the largest + Type: unsigned cooling state accepted. + Size: one cell + * Trip points The trip node is a node to describe a point in the temperature domain @@ -225,8 +226,8 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-state = <0>; - cooling-max-state = <3>; + cooling-min-level = <0>; + cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -240,8 +241,8 @@ cpus { */ fan0: fan@0x48 { ... - cooling-min-state = <0>; - cooling-max-state = <9>; + cooling-min-level = <0>; + cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index d71ef07bca5d..a057b75ba4b5 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -6,6 +6,7 @@ Required properties: "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" + "xlnx,zynq-usb-2.20a" - reg: base address and length of the registers - interrupts: interrupt for the USB controller diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 64a4ca6cf96f..7d48f63db44e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" - "renesas,usbhs-r8a7794" + - "renesas,usbhs-r8a7795" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ac5f0c34ae00..82d2ac97af74 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -203,6 +203,7 @@ sitronix Sitronix Technology Corporation skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. +socionext Socionext Inc. solidrun SolidRun solomon Solomon Systech Limited sony Sony Corporation |