diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 106 insertions, 42 deletions
diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt deleted file mode 100644 index 3e56c1b34a4c..000000000000 --- a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt +++ /dev/null @@ -1,41 +0,0 @@ -Driver a GPIO line that can be used to turn the power off. - -The driver supports both level triggered and edge triggered power off. -At driver load time, the driver will request the given gpio line and -install a handler to power off the system. If the optional properties -'input' is not found, the GPIO line will be driven in the inactive -state. Otherwise its configured as an input. - -When the power-off handler is called, the gpio is configured as an -output, and drive active, so triggering a level triggered power off -condition. This will also cause an inactive->active edge condition, so -triggering positive edge triggered power off. After a delay of 100ms, -the GPIO is set to inactive, thus causing an active->inactive edge, -triggering negative edge triggered power off. After another 100ms -delay the GPIO is driver active again. If the power is still on and -the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. - -Required properties: -- compatible : should be "gpio-poweroff". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to power down the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- input : Initially configure the GPIO line as an input. Only reconfigure - it to an output when the power-off handler is called. If this optional - property is not specified, the GPIO is initialized as an output in its - inactive state. -- active-delay-ms: Delay (default 100) to wait after driving gpio active -- inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive -- timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is - specified, 3000 ms is used. - -Examples: - -gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; - timeout-ms = <3000>; -}; diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml new file mode 100644 index 000000000000..45d66c775115 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/reset/gpio-poweroff.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controlled power off + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: > + System power off support via a GPIO line. When a shutdown is + executed the operating system is expected to switch the GPIO + from inactive to active. After a delay (active-delay-ms) it + is expected to be switched back to inactive. After another + delay (inactive-delay-ms) it is configured as active again. + Finally the operating system assumes the power off failed if + the system is still running after waiting some time (timeout-ms). + +properties: + compatible: + const: gpio-poweroff + + gpios: + maxItems: 1 + + input: + type: boolean + description: > + Initially configure the GPIO line as an input. Only reconfigure + it to an output when the power-off sequence is initiated. If this optional + property is not specified, the GPIO is initialized as an output in its inactive state. + + active-delay-ms: + default: 100 + description: Delay to wait after driving gpio active + + inactive-delay-ms: + default: 100 + description: Delay to wait after driving gpio inactive + + timeout-ms: + default: 3000 + description: Time to wait before assuming the power off sequence failed. + +required: + - compatible + - gpios + +additionalProperties: false + +examples: + - | + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; + timeout-ms = <3000>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max77976.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max77976.yaml new file mode 100644 index 000000000000..675b9b26d233 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max77976.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/maxim,max77976.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated MAX77976 Battery charger + +maintainers: + - Luca Ceresoli <luca@lucaceresoli.net> + +description: | + The Maxim MAX77976 is a 19Vin / 5.5A, 1-Cell Li+ battery charger + configured via I2C. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: maxim,max77976 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@6b { + compatible = "maxim,max77976"; + reg = <0x6b>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml index bc8904872d1b..caeff68c66d5 100644 --- a/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml +++ b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml @@ -11,7 +11,9 @@ maintainers: properties: compatible: - const: qcom,pm8941-charger + enum: + - qcom,pm8226-charger + - qcom,pm8941-charger reg: maxItems: 1 |