diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
6 files changed, 574 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index 3c5c631328d3..aef1d200a9b2 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -31,8 +31,9 @@ specific to ARM. - compatible Usage: required Value type: <string> - Definition: must be set to + Definition: must contain one of the following: "arm,cci-400" + "arm,cci-500" - reg Usage: required @@ -99,6 +100,7 @@ specific to ARM. "arm,cci-400-pmu,r1" "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has secure acces to CCI registers + "arm,cci-500-pmu,r0" - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt index f3db93c85eea..3338a2834ad7 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt @@ -1,6 +1,9 @@ NVIDIA Tegra Memory Controller device tree bindings =================================================== +memory-controller node +---------------------- + Required properties: - compatible: Should be "nvidia,tegra<chip>-mc" - reg: Physical base address and length of the controller's registers. @@ -15,9 +18,49 @@ Required properties: This device implements an IOMMU that complies with the generic IOMMU binding. See ../iommu/iommu.txt for details. -Example: --------- +emc-timings subnode +------------------- + +The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in +register PMC_STRAPPING_OPT_A). + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is used for. + +timing subnode +-------------- + +Each "emc-timings" node should contain a subnode for every supported EMC clock rate. + +Required properties for timing nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- nvidia,emem-configuration : Values to be written to the EMEM register block. For the Tegra124 SoC +(see section "15.6.1 MC Registers" in the TRM), these are the registers whose values need to be +specified, according to the board documentation: + + MC_EMEM_ARB_CFG + MC_EMEM_ARB_OUTSTANDING_REQ + MC_EMEM_ARB_TIMING_RCD + MC_EMEM_ARB_TIMING_RP + MC_EMEM_ARB_TIMING_RC + MC_EMEM_ARB_TIMING_RAS + MC_EMEM_ARB_TIMING_FAW + MC_EMEM_ARB_TIMING_RRD + MC_EMEM_ARB_TIMING_RAP2PRE + MC_EMEM_ARB_TIMING_WAP2PRE + MC_EMEM_ARB_TIMING_R2R + MC_EMEM_ARB_TIMING_W2W + MC_EMEM_ARB_TIMING_R2W + MC_EMEM_ARB_TIMING_W2R + MC_EMEM_ARB_DA_TURNS + MC_EMEM_ARB_DA_COVERS + MC_EMEM_ARB_MISC0 + MC_EMEM_ARB_MISC1 + MC_EMEM_ARB_RING1_THROTTLE +Example SoC include file: + +/ { mc: memory-controller@0,70019000 { compatible = "nvidia,tegra124-mc"; reg = <0x0 0x70019000 0x0 0x1000>; @@ -34,3 +77,40 @@ Example: ... iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; }; +}; + +Example board file: + +/ { + memory-controller@0,70019000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 /* MC_EMEM_ARB_CFG */ + 0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RCD */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RP */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RC */ + 0x00000000 /* MC_EMEM_ARB_TIMING_RAS */ + 0x00000002 /* MC_EMEM_ARB_TIMING_FAW */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */ + 0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2R */ + 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2W */ + 0x00000006 /* MC_EMEM_ARB_TIMING_W2R */ + 0x06030203 /* MC_EMEM_ARB_DA_TURNS */ + 0x000a0402 /* MC_EMEM_ARB_DA_COVERS */ + 0x77e30303 /* MC_EMEM_ARB_MISC0 */ + 0x70000f03 /* MC_EMEM_ARB_MISC1 */ + 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt b/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt new file mode 100644 index 000000000000..b59c625d6336 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt @@ -0,0 +1,374 @@ +NVIDIA Tegra124 SoC EMC (external memory controller) +==================================================== + +Required properties : +- compatible : Should be "nvidia,tegra124-emc". +- reg : physical base address and length of the controller's registers. +- nvidia,memory-controller : phandle of the MC driver. + +The node should contain a "emc-timings" subnode for each supported RAM type +(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address +being its RAM_CODE. + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is +used for. + +Each "emc-timings" node should contain a "timing" subnode for every supported +EMC clock rate. The "timing" subnodes should have the clock rate in Hz as +their unit address. + +Required properties for "timing" nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- The following properties contain EMC timing characterization values +(specified in the board documentation) : + - nvidia,emc-auto-cal-config : EMC_AUTO_CAL_CONFIG + - nvidia,emc-auto-cal-config2 : EMC_AUTO_CAL_CONFIG2 + - nvidia,emc-auto-cal-config3 : EMC_AUTO_CAL_CONFIG3 + - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL + - nvidia,emc-bgbias-ctl0 : EMC_BGBIAS_CTL0 + - nvidia,emc-cfg : EMC_CFG + - nvidia,emc-cfg-2 : EMC_CFG_2 + - nvidia,emc-ctt-term-ctrl : EMC_CTT_TERM_CTRL + - nvidia,emc-mode-1 : Mode Register 1 + - nvidia,emc-mode-2 : Mode Register 2 + - nvidia,emc-mode-4 : Mode Register 4 + - nvidia,emc-mode-reset : Mode Register 0 + - nvidia,emc-mrs-wait-cnt : EMC_MRS_WAIT_CNT + - nvidia,emc-sel-dpd-ctrl : EMC_SEL_DPD_CTRL + - nvidia,emc-xm2dqspadctrl2 : EMC_XM2DQSPADCTRL2 + - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change + - nvidia,emc-zcal-interval : EMC_ZCAL_INTERVAL +- nvidia,emc-configuration : EMC timing characterization data. These are the +registers (see section "15.6.2 EMC Registers" in the TRM) whose values need to +be specified, according to the board documentation: + + EMC_RC + EMC_RFC + EMC_RFC_SLR + EMC_RAS + EMC_RP + EMC_R2W + EMC_W2R + EMC_R2P + EMC_W2P + EMC_RD_RCD + EMC_WR_RCD + EMC_RRD + EMC_REXT + EMC_WEXT + EMC_WDV + EMC_WDV_MASK + EMC_QUSE + EMC_QUSE_WIDTH + EMC_IBDLY + EMC_EINPUT + EMC_EINPUT_DURATION + EMC_PUTERM_EXTRA + EMC_PUTERM_WIDTH + EMC_PUTERM_ADJ + EMC_CDB_CNTL_1 + EMC_CDB_CNTL_2 + EMC_CDB_CNTL_3 + EMC_QRST + EMC_QSAFE + EMC_RDV + EMC_RDV_MASK + EMC_REFRESH + EMC_BURST_REFRESH_NUM + EMC_PRE_REFRESH_REQ_CNT + EMC_PDEX2WR + EMC_PDEX2RD + EMC_PCHG2PDEN + EMC_ACT2PDEN + EMC_AR2PDEN + EMC_RW2PDEN + EMC_TXSR + EMC_TXSRDLL + EMC_TCKE + EMC_TCKESR + EMC_TPD + EMC_TFAW + EMC_TRPAB + EMC_TCLKSTABLE + EMC_TCLKSTOP + EMC_TREFBW + EMC_FBIO_CFG6 + EMC_ODT_WRITE + EMC_ODT_READ + EMC_FBIO_CFG5 + EMC_CFG_DIG_DLL + EMC_CFG_DIG_DLL_PERIOD + EMC_DLL_XFORM_DQS0 + EMC_DLL_XFORM_DQS1 + EMC_DLL_XFORM_DQS2 + EMC_DLL_XFORM_DQS3 + EMC_DLL_XFORM_DQS4 + EMC_DLL_XFORM_DQS5 + EMC_DLL_XFORM_DQS6 + EMC_DLL_XFORM_DQS7 + EMC_DLL_XFORM_DQS8 + EMC_DLL_XFORM_DQS9 + EMC_DLL_XFORM_DQS10 + EMC_DLL_XFORM_DQS11 + EMC_DLL_XFORM_DQS12 + EMC_DLL_XFORM_DQS13 + EMC_DLL_XFORM_DQS14 + EMC_DLL_XFORM_DQS15 + EMC_DLL_XFORM_QUSE0 + EMC_DLL_XFORM_QUSE1 + EMC_DLL_XFORM_QUSE2 + EMC_DLL_XFORM_QUSE3 + EMC_DLL_XFORM_QUSE4 + EMC_DLL_XFORM_QUSE5 + EMC_DLL_XFORM_QUSE6 + EMC_DLL_XFORM_QUSE7 + EMC_DLL_XFORM_ADDR0 + EMC_DLL_XFORM_ADDR1 + EMC_DLL_XFORM_ADDR2 + EMC_DLL_XFORM_ADDR3 + EMC_DLL_XFORM_ADDR4 + EMC_DLL_XFORM_ADDR5 + EMC_DLL_XFORM_QUSE8 + EMC_DLL_XFORM_QUSE9 + EMC_DLL_XFORM_QUSE10 + EMC_DLL_XFORM_QUSE11 + EMC_DLL_XFORM_QUSE12 + EMC_DLL_XFORM_QUSE13 + EMC_DLL_XFORM_QUSE14 + EMC_DLL_XFORM_QUSE15 + EMC_DLI_TRIM_TXDQS0 + EMC_DLI_TRIM_TXDQS1 + EMC_DLI_TRIM_TXDQS2 + EMC_DLI_TRIM_TXDQS3 + EMC_DLI_TRIM_TXDQS4 + EMC_DLI_TRIM_TXDQS5 + EMC_DLI_TRIM_TXDQS6 + EMC_DLI_TRIM_TXDQS7 + EMC_DLI_TRIM_TXDQS8 + EMC_DLI_TRIM_TXDQS9 + EMC_DLI_TRIM_TXDQS10 + EMC_DLI_TRIM_TXDQS11 + EMC_DLI_TRIM_TXDQS12 + EMC_DLI_TRIM_TXDQS13 + EMC_DLI_TRIM_TXDQS14 + EMC_DLI_TRIM_TXDQS15 + EMC_DLL_XFORM_DQ0 + EMC_DLL_XFORM_DQ1 + EMC_DLL_XFORM_DQ2 + EMC_DLL_XFORM_DQ3 + EMC_DLL_XFORM_DQ4 + EMC_DLL_XFORM_DQ5 + EMC_DLL_XFORM_DQ6 + EMC_DLL_XFORM_DQ7 + EMC_XM2CMDPADCTRL + EMC_XM2CMDPADCTRL4 + EMC_XM2CMDPADCTRL5 + EMC_XM2DQPADCTRL2 + EMC_XM2DQPADCTRL3 + EMC_XM2CLKPADCTRL + EMC_XM2CLKPADCTRL2 + EMC_XM2COMPPADCTRL + EMC_XM2VTTGENPADCTRL + EMC_XM2VTTGENPADCTRL2 + EMC_XM2VTTGENPADCTRL3 + EMC_XM2DQSPADCTRL3 + EMC_XM2DQSPADCTRL4 + EMC_XM2DQSPADCTRL5 + EMC_XM2DQSPADCTRL6 + EMC_DSR_VTTGEN_DRV + EMC_TXDSRVTTGEN + EMC_FBIO_SPARE + EMC_ZCAL_WAIT_CNT + EMC_MRS_WAIT_CNT2 + EMC_CTT + EMC_CTT_DURATION + EMC_CFG_PIPE + EMC_DYN_SELF_REF_CONTROL + EMC_QPOP + +Example SoC include file: + +/ { + emc@0,7001b000 { + compatible = "nvidia,tegra124-emc"; + reg = <0x0 0x7001b000 0x0 0x1000>; + + nvidia,memory-controller = <&mc>; + }; +}; + +Example board file: + +/ { + emc@0,7001b000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 /* EMC_RC */ + 0x00000003 /* EMC_RFC */ + 0x00000000 /* EMC_RFC_SLR */ + 0x00000000 /* EMC_RAS */ + 0x00000000 /* EMC_RP */ + 0x00000004 /* EMC_R2W */ + 0x0000000a /* EMC_W2R */ + 0x00000003 /* EMC_R2P */ + 0x0000000b /* EMC_W2P */ + 0x00000000 /* EMC_RD_RCD */ + 0x00000000 /* EMC_WR_RCD */ + 0x00000003 /* EMC_RRD */ + 0x00000003 /* EMC_REXT */ + 0x00000000 /* EMC_WEXT */ + 0x00000006 /* EMC_WDV */ + 0x00000006 /* EMC_WDV_MASK */ + 0x00000006 /* EMC_QUSE */ + 0x00000002 /* EMC_QUSE_WIDTH */ + 0x00000000 /* EMC_IBDLY */ + 0x00000005 /* EMC_EINPUT */ + 0x00000005 /* EMC_EINPUT_DURATION */ + 0x00010000 /* EMC_PUTERM_EXTRA */ + 0x00000003 /* EMC_PUTERM_WIDTH */ + 0x00000000 /* EMC_PUTERM_ADJ */ + 0x00000000 /* EMC_CDB_CNTL_1 */ + 0x00000000 /* EMC_CDB_CNTL_2 */ + 0x00000000 /* EMC_CDB_CNTL_3 */ + 0x00000004 /* EMC_QRST */ + 0x0000000c /* EMC_QSAFE */ + 0x0000000d /* EMC_RDV */ + 0x0000000f /* EMC_RDV_MASK */ + 0x00000060 /* EMC_REFRESH */ + 0x00000000 /* EMC_BURST_REFRESH_NUM */ + 0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */ + 0x00000002 /* EMC_PDEX2WR */ + 0x00000002 /* EMC_PDEX2RD */ + 0x00000001 /* EMC_PCHG2PDEN */ + 0x00000000 /* EMC_ACT2PDEN */ + 0x00000007 /* EMC_AR2PDEN */ + 0x0000000f /* EMC_RW2PDEN */ + 0x00000005 /* EMC_TXSR */ + 0x00000005 /* EMC_TXSRDLL */ + 0x00000004 /* EMC_TCKE */ + 0x00000005 /* EMC_TCKESR */ + 0x00000004 /* EMC_TPD */ + 0x00000000 /* EMC_TFAW */ + 0x00000000 /* EMC_TRPAB */ + 0x00000005 /* EMC_TCLKSTABLE */ + 0x00000005 /* EMC_TCLKSTOP */ + 0x00000064 /* EMC_TREFBW */ + 0x00000000 /* EMC_FBIO_CFG6 */ + 0x00000000 /* EMC_ODT_WRITE */ + 0x00000000 /* EMC_ODT_READ */ + 0x106aa298 /* EMC_FBIO_CFG5 */ + 0x002c00a0 /* EMC_CFG_DIG_DLL */ + 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ + 0x00064000 /* EMC_DLL_XFORM_DQS0 */ + 0x00064000 /* EMC_DLL_XFORM_DQS1 */ + 0x00064000 /* EMC_DLL_XFORM_DQS2 */ + 0x00064000 /* EMC_DLL_XFORM_DQS3 */ + 0x00064000 /* EMC_DLL_XFORM_DQS4 */ + 0x00064000 /* EMC_DLL_XFORM_DQS5 */ + 0x00064000 /* EMC_DLL_XFORM_DQS6 */ + 0x00064000 /* EMC_DLL_XFORM_DQS7 */ + 0x00064000 /* EMC_DLL_XFORM_DQS8 */ + 0x00064000 /* EMC_DLL_XFORM_DQS9 */ + 0x00064000 /* EMC_DLL_XFORM_DQS10 */ + 0x00064000 /* EMC_DLL_XFORM_DQS11 */ + 0x00064000 /* EMC_DLL_XFORM_DQS12 */ + 0x00064000 /* EMC_DLL_XFORM_DQS13 */ + 0x00064000 /* EMC_DLL_XFORM_DQS14 */ + 0x00064000 /* EMC_DLL_XFORM_DQS15 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE0 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE1 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE2 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE3 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR0 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR1 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR2 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR3 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR4 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE8 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE9 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE10 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE11 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE12 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE13 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE14 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE15 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS8 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS9 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS10 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS11 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS12 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS13 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS14 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS15 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ0 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ1 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ2 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ3 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ4 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ5 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ6 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ7 */ + 0x10000280 /* EMC_XM2CMDPADCTRL */ + 0x00000000 /* EMC_XM2CMDPADCTRL4 */ + 0x00111111 /* EMC_XM2CMDPADCTRL5 */ + 0x00000000 /* EMC_XM2DQPADCTRL2 */ + 0x00000000 /* EMC_XM2DQPADCTRL3 */ + 0x77ffc081 /* EMC_XM2CLKPADCTRL */ + 0x00000e0e /* EMC_XM2CLKPADCTRL2 */ + 0x81f1f108 /* EMC_XM2COMPPADCTRL */ + 0x07070004 /* EMC_XM2VTTGENPADCTRL */ + 0x0000003f /* EMC_XM2VTTGENPADCTRL2 */ + 0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */ + 0x51451400 /* EMC_XM2DQSPADCTRL3 */ + 0x00514514 /* EMC_XM2DQSPADCTRL4 */ + 0x00514514 /* EMC_XM2DQSPADCTRL5 */ + 0x51451400 /* EMC_XM2DQSPADCTRL6 */ + 0x0000003f /* EMC_DSR_VTTGEN_DRV */ + 0x00000007 /* EMC_TXDSRVTTGEN */ + 0x00000000 /* EMC_FBIO_SPARE */ + 0x00000042 /* EMC_ZCAL_WAIT_CNT */ + 0x000e000e /* EMC_MRS_WAIT_CNT2 */ + 0x00000000 /* EMC_CTT */ + 0x00000003 /* EMC_CTT_DURATION */ + 0x0000f2f3 /* EMC_CFG_PIPE */ + 0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */ + 0x0000000a /* EMC_QPOP */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/mfd.txt b/Documentation/devicetree/bindings/mfd/mfd.txt new file mode 100644 index 000000000000..af9d6931a1a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mfd.txt @@ -0,0 +1,41 @@ +Multi-Function Devices (MFD) + +These devices comprise a nexus for heterogeneous hardware blocks containing +more than one non-unique yet varying hardware functionality. + +A typical MFD can be: + +- A mixed signal ASIC on an external bus, sometimes a PMIC (Power Management + Integrated Circuit) that is manufactured in a lower technology node (rough + silicon) that handles analog drivers for things like audio amplifiers, LED + drivers, level shifters, PHY (physical interfaces to things like USB or + ethernet), regulators etc. + +- A range of memory registers containing "miscellaneous system registers" also + known as a system controller "syscon" or any other memory range containing a + mix of unrelated hardware devices. + +Optional properties: + +- compatible : "simple-mfd" - this signifies that the operating system should + consider all subnodes of the MFD device as separate devices akin to how + "simple-bus" inidicates when to see subnodes as children for a simple + memory-mapped bus. For more complex devices, when the nexus driver has to + probe registers to figure out what child devices exist etc, this should not + be used. In the latter case the child devices will be determined by the + operating system. + +Example: + +foo@1000 { + compatible = "syscon", "simple-mfd"; + reg = <0x01000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "myled"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt index 47b205cc9cc7..4556359c5876 100644 --- a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt +++ b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt @@ -10,3 +10,5 @@ Required properties: The second entry gives the physical address and length of the registers indicating the strapping options. +Optional properties: +- nvidia,long-ram-code: If present, the RAM code is long (4 bit). If not, short (2 bit). diff --git a/Documentation/devicetree/bindings/soc/sunxi/sram.txt b/Documentation/devicetree/bindings/soc/sunxi/sram.txt new file mode 100644 index 000000000000..067698112f5f --- /dev/null +++ b/Documentation/devicetree/bindings/soc/sunxi/sram.txt @@ -0,0 +1,72 @@ +Allwinnner SoC SRAM controllers +----------------------------------------------------- + +The SRAM controller found on most Allwinner devices is represented by +a regular node for the SRAM controller itself, with sub-nodes +reprensenting the SRAM handled by the SRAM controller. + +Controller Node +--------------- + +Required properties: +- compatible : "allwinner,sun4i-a10-sram-controller" +- reg : sram controller register offset + length + +SRAM nodes +---------- + +Each SRAM is described using the mmio-sram bindings documented in +Documentation/devicetree/bindings/misc/sram.txt + +Each SRAM will have SRAM sections that are going to be handled by the +SRAM controller as subnodes. These sections are represented following +once again the representation described in the mmio-sram binding. + +The valid sections compatible are: + - allwinner,sun4i-a10-sram-a3-a4 + - allwinner,sun4i-a10-sram-d + +Devices using SRAM sections +--------------------------- + +Some devices need to request to the SRAM controller to map an SRAM for +their exclusive use. + +The relationship between such a device and an SRAM section is +expressed through the allwinner,sram property, that will take a +phandle and an argument. + +This valid values for this argument are: + - 0: CPU + - 1: Device + +Example +------- +sram-controller@01c00000 { + compatible = "allwinner,sun4i-a10-sram-controller"; + reg = <0x01c00000 0x30>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sram_a: sram@00000000 { + compatible = "mmio-sram"; + reg = <0x00000000 0xc000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00000000 0xc000>; + + emac_sram: sram-section@8000 { + compatible = "allwinner,sun4i-a10-sram-a3-a4"; + reg = <0x8000 0x4000>; + status = "disabled"; + }; + }; +}; + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + ... + + allwinner,sram = <&emac_sram 1>; +}; |