diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
628 files changed, 16033 insertions, 1489 deletions
diff --git a/Documentation/devicetree/bindings/arc/eznps.txt b/Documentation/devicetree/bindings/arc/eznps.txt new file mode 100644 index 000000000000..1aa50c640678 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/eznps.txt @@ -0,0 +1,7 @@ +EZchip NPS Network Processor Platforms Device Tree Bindings +--------------------------------------------------------------------------- + +Appliance main board with NPS400 ASIC. + +Required root node properties: + - compatible = "ezchip,arc-nps"; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt index 5a6b16070a33..4a1714f96bab 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -61,7 +61,9 @@ Required Properties: - #address-cells: must be 1 - #size-cells: must be 1 - interrupts : Should be single bit error interrupt, then double bit error - interrupt. Note the rising edge type. + interrupt. +- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller +- #interrupt-cells : must be set to 2. - ranges : standard definition, should translate from local addresses Subcomponents: @@ -70,11 +72,64 @@ L2 Cache ECC Required Properties: - compatible : Should be "altr,socfpga-a10-l2-ecc" - reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. On-Chip RAM ECC Required Properties: - compatible : Should be "altr,socfpga-a10-ocram-ecc" - reg : Address and size for ECC block registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +Ethernet FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-eth-mac-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent Ethernet node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +NAND FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-nand-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent NAND node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +DMA FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-dma-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent DMA node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +USB FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-usb-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent USB node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +QSPI FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-qspi-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent QSPI node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +SDMMC FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-sdmmc-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent SD/MMC node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order for port A, and then single bit error interrupt, + then double bit error interrupt in this order for port B. Example: @@ -85,15 +140,94 @@ Example: #size-cells = <1>; interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>, <0 0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; ranges; l2-ecc@ffd06010 { compatible = "altr,socfpga-a10-l2-ecc"; reg = <0xffd06010 0x4>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, + <32 IRQ_TYPE_LEVEL_HIGH>; }; ocram-ecc@ff8c3000 { compatible = "altr,socfpga-a10-ocram-ecc"; reg = <0xff8c3000 0x90>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>, + <33 IRQ_TYPE_LEVEL_HIGH> ; + }; + + emac0-rx-ecc@ff8c0800 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0800 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>, + <36 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-tx-ecc@ff8c0c00 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0c00 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>, + <37 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-buf-ecc@ff8c2000 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2000 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>, + <43 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-rd-ecc@ff8c2400 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2400 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>, + <45 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-wr-ecc@ff8c2800 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2800 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>, + <44 IRQ_TYPE_LEVEL_HIGH>; + }; + + dma-ecc@ff8c8000 { + compatible = "altr,socfpga-dma-ecc"; + reg = <0xff8c8000 0x400>; + altr,ecc-parent = <&pdma>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <42 IRQ_TYPE_LEVEL_HIGH>; + + usb0-ecc@ff8c8800 { + compatible = "altr,socfpga-usb-ecc"; + reg = <0xff8c8800 0x400>; + altr,ecc-parent = <&usb0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <34 IRQ_TYPE_LEVEL_HIGH>; + }; + + qspi-ecc@ff8c8400 { + compatible = "altr,socfpga-qspi-ecc"; + reg = <0xff8c8400 0x400>; + altr,ecc-parent = <&qspi>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>, + <46 IRQ_TYPE_LEVEL_HIGH>; + }; + + sdmmc-ecc@ff8c2c00 { + compatible = "altr,socfpga-sdmmc-ecc"; + reg = <0xff8c2c00 0x400>; + altr,ecc-parent = <&mmc>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>, + <47 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>, + <48 IRQ_TYPE_LEVEL_HIGH>; }; }; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 8a5122ab19b0..fcc6f6c10803 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -25,3 +25,6 @@ Board compatible values: - "tronsmart,vega-s95-pro", "tronsmart,vega-s95" (Meson gxbb) - "tronsmart,vega-s95-meta", "tronsmart,vega-s95" (Meson gxbb) - "tronsmart,vega-s95-telos", "tronsmart,vega-s95" (Meson gxbb) + - "hardkernel,odroid-c2" (Meson gxbb) + - "amlogic,p200" (Meson gxbb) + - "amlogic,p201" (Meson gxbb) diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index e774128935d5..ef5fbe9a77c7 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -25,6 +25,12 @@ to deliver its interrupts via SPIs. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. +- fsl,erratum-a008585 : A boolean property. Indicates the presence of + QorIQ erratum A-008585, which says that reading the counter is + unreliable unless the same value is returned by back-to-back reads. + This also affects writes to the tval register, due to the implicit + counter read. + ** Optional properties: - arm,cpu-registers-not-fw-configured : Firmware does not initialize diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt index 313dabdc14f9..faa4b44572e3 100644 --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -87,10 +87,33 @@ Required properties: implementation for the IDs to use. For Juno R0 and Juno R1 refer to [3]. +Power domain bindings for the power domains based on SCPI Message Protocol +------------------------------------------------------------ + +This binding uses the generic power domain binding[4]. + +PM domain providers +=================== + +Required properties: + - #power-domain-cells : Should be 1. Contains the device or the power + domain ID value used by SCPI commands. + - num-domains: Total number of power domains provided by SCPI. This is + needed as the SCPI message protocol lacks a mechanism to + query this information at runtime. + +PM domain consumers +=================== + +Required properties: + - power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle. + [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html [1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/thermal/thermal.txt [3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html +[4] Documentation/devicetree/bindings/power/power_domain.txt Example: @@ -144,6 +167,12 @@ scpi_protocol: scpi@2e000000 { compatible = "arm,scpi-sensors"; #thermal-sensor-cells = <1>; }; + + scpi_devpd: scpi-power-domains { + compatible = "arm,scpi-power-domains"; + num-domains = <2>; + #power-domain-cells = <1>; + }; }; cpu@0 { @@ -156,6 +185,7 @@ hdlcd@7ff60000 { ... reg = <0 0x7ff60000 0 0x1000>; clocks = <&scpi_clk 4>; + power-domains = <&scpi_devpd 1>; }; thermal-zones { @@ -186,3 +216,7 @@ The thermal-sensors property in the soc_thermal node uses the temperature sensor provided by SCP firmware to setup a thermal zone. The ID "3" is the sensor identifier for the temperature sensor as used by the firmware. + +The num-domains property in scpi-power-domains domain specifies that +SCPI provides 2 power domains. The hdlcd node uses the power domain with +domain ID 1. diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 0226bc2cc1f6..ab318a56fca2 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -93,6 +93,14 @@ Required nodes: a core-module with regs and the compatible strings "arm,core-module-versatile", "syscon" +Optional nodes: + +- arm,versatile-ib2-syscon : if the Versatile has an IB2 interface + board mounted, this has a separate system controller that is + defined in this node. + Required properties: + compatible = "arm,versatile-ib2-syscon", "syscon" + ARM RealView Boards ------------------- The RealView boards cover tailored evaluation boards that are used to explore diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 7fd64ec9ee1d..e1f5ad855f14 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -41,6 +41,10 @@ compatible: must be one of: - "atmel,sama5d43" - "atmel,sama5d44" +Chipid required properties: +- compatible: Should be "atmel,sama5d2-chipid" +- reg : Should contain registers location and length + PIT Timer required properties: - compatible: Should be "atmel,at91sam9260-pit" - reg: Should contain registers location and length @@ -147,6 +151,65 @@ Example: clocks = <&clk32k>; }; +SHDWC SAMA5D2-Compatible Shutdown Controller + +1) shdwc node + +required properties: +- compatible: should be "atmel,sama5d2-shdwc". +- reg: should contain registers location and length +- clocks: phandle to input clock. +- #address-cells: should be one. The cell is the wake-up input index. +- #size-cells: should be zero. + +optional properties: + +- debounce-delay-us: minimum wake-up inputs debouncer period in + microseconds. It's usually a board-related property. +- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up. + +The node contains child nodes for each wake-up input that the platform uses. + +2) input nodes + +Wake-up input nodes are usually described in the "board" part of the Device +Tree. Note also that input 0 is linked to the wake-up pin and is frequently +used. + +Required properties: +- reg: should contain the wake-up input index [0 - 15]. + +Optional properties: +- atmel,wakeup-active-high: boolean, the corresponding wake-up input described + by the child, forces the wake-up of the core power supply on a high level. + The default is to be active low. + +Example: + +On the SoC side: + shdwc@f8048010 { + compatible = "atmel,sama5d2-shdwc"; + reg = <0xf8048010 0x10>; + clocks = <&clk32k>; + #address-cells = <1>; + #size-cells = <0>; + atmel,wakeup-rtc-timer; + }; + +On the board side: + shdwc@f8048010 { + debounce-delay-us = <976>; + + input@0 { + reg = <0>; + }; + + input@1 { + reg = <1>; + atmel,wakeup-active-high; + }; + }; + Special Function Registers (SFR) Special Function Registers (SFR) manage specific aspects of the integrated @@ -155,7 +218,7 @@ elsewhere. required properties: - compatible: Should be "atmel,<chip>-sfr", "syscon". - <chip> can be "sama5d3" or "sama5d4". + <chip> can be "sama5d3", "sama5d4" or "sama5d2". - reg: Should contain registers location and length sfr@f0038000 { diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt index 8240c023e202..e3f996920403 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt @@ -5,7 +5,7 @@ CPUs in the following Broadcom SoCs: BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664 The enable method is specified by defining the following required -properties in the "cpus" device tree node: +properties in the "cpu" device tree node: - enable-method = "brcm,bcm11351-cpu-method"; - secondary-boot-reg = <...>; @@ -19,8 +19,6 @@ Example: cpus { #address-cells = <1>; #size-cells = <0>; - enable-method = "brcm,bcm11351-cpu-method"; - secondary-boot-reg = <0x3500417c>; cpu0: cpu@0 { device_type = "cpu"; @@ -32,5 +30,7 @@ Example: device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; + enable-method = "brcm,bcm11351-cpu-method"; + secondary-boot-reg = <0x3500417c>; }; }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt new file mode 100644 index 000000000000..a3af54c0e404 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt @@ -0,0 +1,36 @@ +Broadcom Kona Family CPU Enable Method +-------------------------------------- +This binding defines the enable method used for starting secondary +CPUs in the following Broadcom SoCs: + BCM23550 + +The enable method is specified by defining the following required +properties in the "cpu" device tree node: + - enable-method = "brcm,bcm23550"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register used to request the ROM holding pen +code release a secondary CPU. The value written to the register is +formed by encoding the target CPU id into the low bits of the +physical start address it should jump to. + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + enable-method = "brcm,bcm23550"; + secondary-boot-reg = <0x3500417c>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt new file mode 100644 index 000000000000..080baad923d6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt @@ -0,0 +1,15 @@ +Broadcom BCM23550 device tree bindings +-------------------------------------- + +This document describes the device tree bindings for boards with the BCM23550 +SoC. + +Required root node property: + - compatible: brcm,bcm23550 + +Example: + / { + model = "BCM23550 SoC"; + compatible = "brcm,bcm23550"; + [...] + } diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 11d3056dc2bd..6ffe08778465 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -30,6 +30,10 @@ Raspberry Pi 2 Model B Required root node properties: compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; +Raspberry Pi 3 Model B +Required root node properties: +compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; + Raspberry Pi Compute Module Required root node properties: compatible = "raspberrypi,compute-module", "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index a1a5a7ecc2fb..0f2153e8fa7e 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -100,7 +100,7 @@ specific to ARM. "arm,cci-400-pmu,r0" "arm,cci-400-pmu,r1" "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has - secure acces to CCI registers + secure access to CCI registers "arm,cci-500-pmu,r0" "arm,cci-550-pmu,r0" - reg: diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 62938eb9697f..fcbae6a5e6c1 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -12,13 +12,33 @@ its hardware characteristcs. * compatible: These have to be supplemented with "arm,primecell" as drivers are using the AMBA bus interface. Possible values include: - - "arm,coresight-etb10", "arm,primecell"; - - "arm,coresight-tpiu", "arm,primecell"; - - "arm,coresight-tmc", "arm,primecell"; - - "arm,coresight-funnel", "arm,primecell"; - - "arm,coresight-etm3x", "arm,primecell"; - - "arm,coresight-etm4x", "arm,primecell"; - - "qcom,coresight-replicator1x", "arm,primecell"; + - Embedded Trace Buffer (version 1.0): + "arm,coresight-etb10", "arm,primecell"; + + - Trace Port Interface Unit: + "arm,coresight-tpiu", "arm,primecell"; + + - Trace Memory Controller, used for Embedded Trace Buffer(ETB), + Embedded Trace FIFO(ETF) and Embedded Trace Router(ETR) + configuration. The configuration mode (ETB, ETF, ETR) is + discovered at boot time when the device is probed. + "arm,coresight-tmc", "arm,primecell"; + + - Trace Funnel: + "arm,coresight-funnel", "arm,primecell"; + + - Embedded Trace Macrocell (version 3.x) and + Program Flow Trace Macrocell: + "arm,coresight-etm3x", "arm,primecell"; + + - Embedded Trace Macrocell (version 4.x): + "arm,coresight-etm4x", "arm,primecell"; + + - Qualcomm Configurable Replicator (version 1.x): + "qcom,coresight-replicator1x", "arm,primecell"; + + - System Trace Macrocell: + "arm,coresight-stm", "arm,primecell"; [1] * reg: physical base address and length of the register set(s) of the component. @@ -36,6 +56,14 @@ its hardware characteristcs. layout using the generic DT graph presentation found in "bindings/graph.txt". +* Additional required properties for System Trace Macrocells (STM): + * reg: along with the physical base address and length of the register + set as described above, another entry is required to describe the + mapping of the extended stimulus port area. + + * reg-names: the only acceptable values are "stm-base" and + "stm-stimulus-base", each corresponding to the areas defined in "reg". + * Required properties for devices that don't show up on the AMBA bus, such as non-configurable replicators: @@ -202,3 +230,22 @@ Example: }; }; }; + +4. STM + stm@20100000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x20100000 0 0x1000>, + <0 0x28000000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + port { + stm_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port2>; + }; + }; + }; + +[1]. There is currently two version of STM: STM32 and STM500. Both +have the same HW interface and as such don't need an explicit binding name. diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 3f0cbbb8395f..e6782d50cbcd 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -193,6 +193,8 @@ nodes to be present and contain the properties described below. "allwinner,sun6i-a31" "allwinner,sun8i-a23" "arm,realview-smp" + "brcm,bcm11351-cpu-method" + "brcm,bcm23550" "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" @@ -204,6 +206,7 @@ nodes to be present and contain the properties described below. "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" + "renesas,apmu" "rockchip,rk3036-smp" "rockchip,rk3066-smp" "ste,dbx500-smp" diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 752a685d926f..dbbc0952021c 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -135,6 +135,10 @@ LS1043A ARMv8 based RDB Board Required root node properties: - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; +LS1043A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls1043a-qds", "fsl,ls1043a"; + LS2080A ARMv8 based Simulator model Required root node properties: - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hi3519-sysctrl.txt b/Documentation/devicetree/bindings/arm/hisilicon/hi3519-sysctrl.txt new file mode 100644 index 000000000000..115c5be0bd0b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/hisilicon/hi3519-sysctrl.txt @@ -0,0 +1,14 @@ +* Hisilicon Hi3519 System Controller Block + +This bindings use the following binding: +Documentation/devicetree/bindings/mfd/syscon.txt + +Required properties: +- compatible: "hisilicon,hi3519-sysctrl". +- reg: the register region of this block + +Examples: +sysctrl: system-controller@12010000 { + compatible = "hisilicon,hi3519-sysctrl", "syscon"; + reg = <0x12010000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index e3ccab114006..83fe816ae050 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -1,29 +1,33 @@ Hisilicon Platforms Device Tree Bindings ---------------------------------------------------- -Hi6220 SoC -Required root node properties: - - compatible = "hisilicon,hi6220"; - Hi4511 Board Required root node properties: - compatible = "hisilicon,hi3620-hi4511"; -HiP04 D01 Board +Hi6220 SoC Required root node properties: - - compatible = "hisilicon,hip04-d01"; + - compatible = "hisilicon,hi6220"; + +HiKey Board +Required root node properties: + - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; HiP01 ca9x2 Board Required root node properties: - compatible = "hisilicon,hip01-ca9x2"; -HiKey Board +HiP04 D01 Board Required root node properties: - - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; + - compatible = "hisilicon,hip04-d01"; HiP05 D02 Board Required root node properties: - compatible = "hisilicon,hip05-d02"; +HiP06 D03 Board +Required root node properties: + - compatible = "hisilicon,hip06-d03"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt index fe0398c5c77b..917199f17965 100644 --- a/Documentation/devicetree/bindings/arm/l2c2x0.txt +++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt @@ -84,6 +84,12 @@ Optional properties: - prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable), <1> (forcibly enable), property absent (retain settings set by firmware) +- arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly + disable), <1> (forcibly enable), property absent (OS specific behavior, + preferably retain firmware settings) +- arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable), + <1> (forcibly enable), property absent (OS specific behavior, + preferably retain firmware settings) Example: diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt new file mode 100644 index 000000000000..8968371d84e2 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt @@ -0,0 +1,35 @@ +Marvell Armada AP806 System Controller +====================================== + +The AP806 is one of the two core HW blocks of the Marvell Armada 7K/8K +SoCs. It contains a system controller, which provides a number +registers giving access to numerous features: clocks, pin-muxing and +many other SoC configuration items. This DT binding allows to describe +this system controller. + +The Device Tree node representing the AP806 system controller provides +a number of clocks: + + - 0: clock of CPU cluster 0 + - 1: clock of CPU cluster 1 + - 2: fixed PLL at 1200 Mhz + - 3: MSS clock, derived from the fixed PLL + +Required properties: + + - compatible: must be: + "marvell,ap806-system-controller", "syscon" + - reg: register area of the AP806 system controller + - #clock-cells: must be set to 1 + - clock-output-names: must be defined to: + "ap-cpu-cluster-0", "ap-cpu-cluster-1", "ap-fixed", "ap-mss" + +Example: + + syscon: system-controller@6f4000 { + compatible = "marvell,ap806-system-controller", "syscon"; + #clock-cells = <1>; + clock-output-names = "ap-cpu-cluster-0", "ap-cpu-cluster-1", + "ap-fixed", "ap-mss"; + reg = <0x6f4000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt new file mode 100644 index 000000000000..30c546900b60 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt @@ -0,0 +1,83 @@ +Marvell Armada CP110 System Controller 0 +======================================== + +The CP110 is one of the two core HW blocks of the Marvell Armada 7K/8K +SoCs. It contains two sets of system control registers, System +Controller 0 and System Controller 1. This Device Tree binding allows +to describe the first system controller, which provides registers to +configure various aspects of the SoC. + +The Device Tree node representing this System Controller 0 provides a +number of clocks: + + - a set of core clocks + - a set of gatable clocks + +Those clocks can be referenced by other Device Tree nodes using two +cells: + - The first cell must be 0 or 1. 0 for the core clocks and 1 for the + gatable clocks. + - The second cell identifies the particular core clock or gatable + clocks. + +The following clocks are available: + - Core clocks + - 0 0 APLL + - 0 1 PPv2 core + - 0 2 EIP + - 0 3 Core + - 0 4 NAND core + - Gatable clocks + - 1 0 Audio + - 1 1 Comm Unit + - 1 2 NAND + - 1 3 PPv2 + - 1 4 SDIO + - 1 5 MG Domain + - 1 6 MG Core + - 1 7 XOR1 + - 1 8 XOR0 + - 1 9 GOP DP + - 1 11 PCIe x1 0 + - 1 12 PCIe x1 1 + - 1 13 PCIe x4 + - 1 14 PCIe / XOR + - 1 15 SATA + - 1 16 SATA USB + - 1 17 Main + - 1 18 SD/MMC + - 1 21 Slow IO (SPI, NOR, BootROM, I2C, UART) + - 1 22 USB3H0 + - 1 23 USB3H1 + - 1 24 USB3 Device + - 1 25 EIP150 + - 1 26 EIP197 + +Required properties: + + - compatible: must be: + "marvell,cp110-system-controller0", "syscon"; + - reg: register area of the CP110 system controller 0 + - #clock-cells: must be set to 2 + - core-clock-output-names must be set to: + "cpm-apll", "cpm-ppv2-core", "cpm-eip", "cpm-core", "cpm-nand-core" + - gate-clock-output-names must be set to: + "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", + "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", + "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; + +Example: + + cpm_syscon0: system-controller@440000 { + compatible = "marvell,cp110-system-controller0", "syscon"; + reg = <0x440000 0x1000>; + #clock-cells = <2>; + core-clock-output-names = "cpm-apll", "cpm-ppv2-core", "cpm-eip", "cpm-core", "cpm-nand-core"; + gate-clock-output-names = "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", + "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", + "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; + }; diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index d9c2a37a4090..c860b245d8c8 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -10,6 +10,7 @@ compatible: Must contain one of "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" + "mediatek,mt6755" "mediatek,mt6795" "mediatek,mt7623" "mediatek,mt8127" @@ -31,6 +32,9 @@ Supported boards: - Evaluation board for MT6592: Required root node properties: - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; +- Evaluation phone for MT6755(Helio P10): + Required root node properties: + - compatible = "mediatek,mt6755-evb", "mediatek,mt6755"; - Evaluation board for MT6795(Helio X10): Required root node properties: - compatible = "mediatek,mt6795-evb", "mediatek,mt6795"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt index 936166fbee09..cb0054ac7121 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt @@ -5,7 +5,8 @@ The Mediatek apmixedsys controller provides the PLLs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-apmixedsys" - "mediatek,mt8135-apmixedsys" - "mediatek,mt8173-apmixedsys" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt new file mode 100644 index 000000000000..4137196dd686 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt @@ -0,0 +1,22 @@ +Mediatek bdpsys controller +============================ + +The Mediatek bdpsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-bdpsys", "syscon" +- #clock-cells: Must be 1 + +The bdpsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +bdpsys: clock-controller@1c000000 { + compatible = "mediatek,mt2701-bdpsys", "syscon"; + reg = <0 0x1c000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt new file mode 100644 index 000000000000..768f3a5bc055 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -0,0 +1,22 @@ +Mediatek ethsys controller +============================ + +The Mediatek ethsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-ethsys", "syscon" +- #clock-cells: Must be 1 + +The ethsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +ethsys: clock-controller@1b000000 { + compatible = "mediatek,mt2701-ethsys", "syscon"; + reg = <0 0x1b000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt new file mode 100644 index 000000000000..beed7b594cea --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt @@ -0,0 +1,24 @@ +Mediatek hifsys controller +============================ + +The Mediatek hifsys controller provides various clocks and reset +outputs to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-hifsys", "syscon" +- #clock-cells: Must be 1 + +The hifsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +hifsys: clock-controller@1a000000 { + compatible = "mediatek,mt2701-hifsys", "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt index b1f2ce17dff8..f6a916686f4c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -5,7 +5,8 @@ The Mediatek imgsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt8173-imgsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index aaf8d1460c4d..1620ec2a5a3f 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -6,7 +6,8 @@ outputs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-infracfg", "syscon" - "mediatek,mt8135-infracfg", "syscon" - "mediatek,mt8173-infracfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt index 4385946eadef..67dd2e473d25 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -5,7 +5,8 @@ The Mediatek mmsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt8173-mmsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index 2f6ff86df49f..e494366782aa 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -6,7 +6,8 @@ outputs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-pericfg", "syscon" - "mediatek,mt8135-pericfg", "syscon" - "mediatek,mt8173-pericfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt index f9e917994ced..9f2fe7860114 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt @@ -5,7 +5,8 @@ The Mediatek topckgen controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-topckgen" - "mediatek,mt8135-topckgen" - "mediatek,mt8173-topckgen" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt index 1faacf1c1b25..2440f73450c3 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -5,7 +5,8 @@ The Mediatek vdecsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt8173-vdecsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt index 007fb5c685a1..d726aeca56be 100644 --- a/Documentation/devicetree/bindings/arm/olimex.txt +++ b/Documentation/devicetree/bindings/arm/olimex.txt @@ -1,5 +1,9 @@ -Olimex i.MX Platforms Device Tree Bindings ------------------------------------------- +Olimex Device Tree Bindings +--------------------------- + +SAM9-L9260 Board +Required root node properties: + - compatible = "olimex,sam9-l9260", "atmel,at91sam9260"; i.MX23 Olinuxino Low Cost Board Required root node properties: diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt index a9b28d74d902..bb5727ae004a 100644 --- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt @@ -42,7 +42,8 @@ Examples: Consumer: ======== See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and -Documentation/devicetree/bindings/arm/gic.txt for further details. +Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt for +further details. An interrupt consumer on an SoC using crossbar will use: interrupts = <GIC_SPI request_number interrupt_level> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 21e71a5e866e..94b57f247615 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -133,6 +133,9 @@ Boards: - AM335X Bone : Low cost community board compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" +- AM3359 ICEv2 : Low cost Industrial Communication Engine EVM. + compatible = "ti,am3359-icev2", "ti,am33xx", "ti,omap3" + - AM335X OrionLXm : Substation Automation Platform compatible = "novatech,am335x-lxm", "ti,am33xx" @@ -169,6 +172,9 @@ Boards: - AM57XX SBC-AM57x compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5728 IDK + compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt new file mode 100644 index 000000000000..b9e49711ba05 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/oxnas.txt @@ -0,0 +1,9 @@ +Oxford Semiconductor OXNAS SoCs Family device tree bindings +------------------------------------------- + +Boards with the OX810SE SoC shall have the following properties: + Required root node property: + compatible: "oxsemi,ox810se" + +Board compatible values: + - "wd,mbwe" (OX810SE) diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 74d5417d0410..61c8b4620415 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -39,7 +39,9 @@ Optional properties: When using a PPI, specifies a list of phandles to CPU nodes corresponding to the set of CPUs which have a PMU of this type signalling the PPI listed in the - interrupts property. + interrupts property, unless this is already specified + by the PPI interrupt specifier itself (in which case + the interrupt-affinity property shouldn't be present). This property should be present when there is more than a single SPI. diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 078c14fcdaaa..666864517069 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -39,6 +39,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- GeekBuying GeekBox: + Required root node properties: + - compatible = "geekbuying,geekbox", "rockchip,rk3368"; + - Google Brain (dev-board): Required root node properties: - compatible = "google,veyron-brain-rev0", "google,veyron-brain", @@ -87,6 +91,10 @@ Rockchip platforms device tree bindings "google,veyron-speedy-rev3", "google,veyron-speedy-rev2", "google,veyron-speedy", "google,veyron", "rockchip,rk3288"; +- mqmaker MiQi: + Required root node properties: + - compatible = "mqmaker,miqi", "rockchip,rk3288"; + - Rockchip RK3368 evb: Required root node properties: - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368"; @@ -97,4 +105,11 @@ Rockchip platforms device tree bindings - Rockchip RK3228 Evaluation board: Required root node properties: - - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; + - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; + +- Rockchip RK3229 Evaluation board: + - compatible = "rockchip,rk3229-evb", "rockchip,rk3229"; + +- Rockchip RK3399 evb: + Required root node properties: + - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 12129c011c8f..0ea7f14ef294 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -2,6 +2,8 @@ Required root node properties: - compatible = should be one or more of the following. + - "samsung,artik5" - for Exynos3250-based Samsung ARTIK5 module. + - "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board. - "samsung,monk" - for Exynos3250-based Samsung Simband board. - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. @@ -45,6 +47,7 @@ Required root node properties: - "hardkernel,odroid-u3" - for Exynos4412-based Hardkernel Odroid U3. - "hardkernel,odroid-x" - for Exynos4412-based Hardkernel Odroid X. - "hardkernel,odroid-x2" - for Exynos4412-based Hardkernel Odroid X2. + - "hardkernel,odroid-xu" - for Exynos5410-based Hardkernel Odroid XU. - "hardkernel,odroid-xu3" - for Exynos5422-based Hardkernel Odroid XU3. - "hardkernel,odroid-xu3-lite" - for Exynos5422-based Hardkernel Odroid XU3 Lite board. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 9cf67e48f222..1df32d339da5 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -29,6 +29,8 @@ SoCs: compatible = "renesas,r8a7794" - R-Car H3 (R8A77950) compatible = "renesas,r8a7795" + - R-Car M3-W (R8A77960) + compatible = "renesas,r8a7796" Boards: @@ -39,6 +41,8 @@ Boards: compatible = "renesas,ape6evm", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA compatible = "renesas,armadillo800eva" + - Blanche (RTP0RC7792SEB00010S) + compatible = "renesas,blanche", "renesas,r8a7792" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" - Genmai (RTK772100BC00000BR) @@ -61,5 +65,7 @@ Boards: compatible = "renesas,porter", "renesas,r8a7791" - Salvator-X (RTP0RC7795SIPB0010S) compatible = "renesas,salvator-x", "renesas,r8a7795"; + - Salvator-X + compatible = "renesas,salvator-x", "renesas,r8a7796"; - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" diff --git a/Documentation/devicetree/bindings/arm/spear-misc.txt b/Documentation/devicetree/bindings/arm/spear-misc.txt index cf649827ffcd..e404e2556b4a 100644 --- a/Documentation/devicetree/bindings/arm/spear-misc.txt +++ b/Documentation/devicetree/bindings/arm/spear-misc.txt @@ -6,4 +6,4 @@ few properties of different peripheral controllers. misc node required properties: - compatible Should be "st,spear1340-misc", "syscon". -- reg: Address range of misc space upto 8K +- reg: Address range of misc space up to 8K diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 73278c6d2dc3..b5a4342c1d46 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -32,7 +32,11 @@ board-specific compatible values: nvidia,whistler toradex,apalis_t30 toradex,apalis_t30-eval + toradex,apalis-tk1 + toradex,apalis-tk1-eval toradex,colibri_t20-512 + toradex,colibri_t30 + toradex,colibri_t30-eval-v3 toradex,iris Trusted Foundations diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index 02c27004d4a8..a74b37b07e5c 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -1,16 +1,20 @@ NVIDIA Tegra Power Management Controller (PMC) +== Power Management Controller Node == + The PMC block interacts with an external Power Management Unit. The PMC mostly controls the entry and exit of the system from different sleep modes. It provides power-gating controllers for SoC and CPU power-islands. Required properties: - name : Should be pmc -- compatible : For Tegra20, must contain "nvidia,tegra20-pmc". For Tegra30, - must contain "nvidia,tegra30-pmc". For Tegra114, must contain - "nvidia,tegra114-pmc". For Tegra124, must contain "nvidia,tegra124-pmc". - Otherwise, must contain "nvidia,<chip>-pmc", plus at least one of the - above, where <chip> is tegra132. +- compatible : Should contain one of the following: + For Tegra20 must contain "nvidia,tegra20-pmc". + For Tegra30 must contain "nvidia,tegra30-pmc". + For Tegra114 must contain "nvidia,tegra114-pmc" + For Tegra124 must contain "nvidia,tegra124-pmc" + For Tegra132 must contain "nvidia,tegra124-pmc" + For Tegra210 must contain "nvidia,tegra210-pmc" - reg : Offset and length of the register set for the device - clocks : Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. @@ -68,6 +72,11 @@ Optional properties for hardware-triggered thermal reset (inside 'i2c-thermtrip' Defaults to 0. Valid values are described in section 12.5.2 "Pinmux Support" of the Tegra4 Technical Reference Manual. +Optional nodes: +- powergates : This node contains a hierarchy of power domain nodes, which + should match the powergates on the Tegra SoC. See "Powergate + Nodes" below. + Example: / SoC dts including file @@ -113,3 +122,76 @@ pmc@7000f400 { }; ... }; + + +== Powergate Nodes == + +Each of the powergate nodes represents a power-domain on the Tegra SoC +that can be power-gated by the Tegra PMC. The name of the powergate node +should be one of the below. Note that not every powergate is applicable +to all Tegra devices and the following list shows which powergates are +applicable to which devices. Please refer to the Tegra TRM for more +details on the various powergates. + + Name Description Devices Applicable + 3d 3D Graphics Tegra20/114/124/210 + 3d0 3D Graphics 0 Tegra30 + 3d1 3D Graphics 1 Tegra30 + aud Audio Tegra210 + dfd Debug Tegra210 + dis Display A Tegra114/124/210 + disb Display B Tegra114/124/210 + heg 2D Graphics Tegra30/114/124/210 + iram Internal RAM Tegra124/210 + mpe MPEG Encode All + nvdec NVIDIA Video Decode Engine Tegra210 + nvjpg NVIDIA JPEG Engine Tegra210 + pcie PCIE Tegra20/30/124/210 + sata SATA Tegra30/124/210 + sor Display interfaces Tegra124/210 + ve2 Video Encode Engine 2 Tegra210 + venc Video Encode Engine All + vdec Video Decode Engine Tegra20/30/114/124 + vic Video Imaging Compositor Tegra124/210 + xusba USB Partition A Tegra114/124/210 + xusbb USB Partition B Tegra114/124/210 + xusbc USB Partition C Tegra114/124/210 + +Required properties: + - clocks: Must contain an entry for each clock required by the PMC for + controlling a power-gate. See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each reset required by the PMC for + controlling a power-gate. See ../reset/reset.txt for details. + - #power-domain-cells: Must be 0. + +Example: + + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + + powergates { + pd_audio: aud { + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + resets = <&tegra_car 198>; + #power-domain-cells = <0>; + }; + }; + }; + + +== Powergate Clients == + +Hardware blocks belonging to a power domain should contain a "power-domains" +property that is a phandle pointing to the corresponding powergate node. + +Example: + + adma: adma@702e2000 { + ... + power-domains = <&pd_audio>; + ... + }; diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt index b8737a8de718..7334c24625fc 100644 --- a/Documentation/devicetree/bindings/arm/ux500/boards.txt +++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt @@ -23,7 +23,7 @@ scu: see binding for arm/scu.txt interrupt-controller: - see binding for arm/gic.txt + see binding for interrupt-controller/arm,gic.txt timer: see binding for arm/twd.txt diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt index 0f7b9c2109f8..c9b9321434ea 100644 --- a/Documentation/devicetree/bindings/arm/xen.txt +++ b/Documentation/devicetree/bindings/arm/xen.txt @@ -11,10 +11,32 @@ the following properties: memory where the grant table should be mapped to, using an HYPERVISOR_memory_op hypercall. The memory region is large enough to map the whole grant table (it is larger or equal to gnttab_max_grant_frames()). + This property is unnecessary when booting Dom0 using ACPI. - interrupts: the interrupt used by Xen to inject event notifications. A GIC node is also required. + This property is unnecessary when booting Dom0 using ACPI. +To support UEFI on Xen ARM virtual platforms, Xen populates the FDT "uefi" node +under /hypervisor with following parameters: + +________________________________________________________________________________ +Name | Size | Description +================================================================================ +xen,uefi-system-table | 64-bit | Guest physical address of the UEFI System + | | Table. +-------------------------------------------------------------------------------- +xen,uefi-mmap-start | 64-bit | Guest physical address of the UEFI memory + | | map. +-------------------------------------------------------------------------------- +xen,uefi-mmap-size | 32-bit | Size in bytes of the UEFI memory map + | | pointed to in previous entry. +-------------------------------------------------------------------------------- +xen,uefi-mmap-desc-size | 32-bit | Size in bytes of each entry in the UEFI + | | memory map. +-------------------------------------------------------------------------------- +xen,uefi-mmap-desc-ver | 32-bit | Version of the mmap descriptor format. +-------------------------------------------------------------------------------- Example (assuming #address-cells = <2> and #size-cells = <2>): @@ -22,4 +44,17 @@ hypervisor { compatible = "xen,xen-4.3", "xen,xen"; reg = <0 0xb0000000 0 0x20000>; interrupts = <1 15 0xf08>; + uefi { + xen,uefi-system-table = <0xXXXXXXXX>; + xen,uefi-mmap-start = <0xXXXXXXXX>; + xen,uefi-mmap-size = <0xXXXXXXXX>; + xen,uefi-mmap-desc-size = <0xXXXXXXXX>; + xen,uefi-mmap-desc-ver = <0xXXXXXXXX>; + }; }; + +The format and meaning of the "xen,uefi-*" parameters are similar to those in +Documentation/arm/uefi.txt, which are provided by the regular UEFI stub. However +they differ because they are provided by the Xen hypervisor, together with a set +of UEFI runtime services implemented via hypercalls, see +http://xenbits.xen.org/docs/unstable/hypercall/x86_64/include,public,platform.h.html. diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 87adfb227ca9..fedc213b5f1a 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -10,6 +10,7 @@ PHYs. Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" + - "brcm,iproc-ahci" - "hisilicon,hisi-ahci" - "cavium,octeon-7130-ahci" - "ibm,476gtr-ahci" diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 60872838f1ad..0a5b3b47f217 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -1,13 +1,14 @@ -* Broadcom SATA3 AHCI Controller for STB +* Broadcom SATA3 AHCI Controller SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: - compatible : should be one or more of - "brcm,bcm7425-ahci" - "brcm,bcm7445-ahci" - "brcm,sata3-ahci" + "brcm,bcm7425-ahci" + "brcm,bcm7445-ahci" + "brcm,bcm-nsp-ahci" + "brcm,sata3-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt index 66c83c3e8915..66c83c3e8915 100644 --- a/Documentation/devicetree/bindings/ata/tegra-sata.txt +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt new file mode 100644 index 000000000000..7ff13be1750b --- /dev/null +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt @@ -0,0 +1,45 @@ +NVIDIA Tegra ACONNECT Bus + +The Tegra ACONNECT bus is an AXI switch which is used to connnect various +components inside the Audio Processing Engine (APE). All CPU accesses to +the APE subsystem go through the ACONNECT via an APB to AXI wrapper. + +Required properties: +- compatible: Must be "nvidia,tegra210-aconnect". +- clocks: Must contain the entries for the APE clock (TEGRA210_CLK_APE), + and APE interface clock (TEGRA210_CLK_APB2APE). +- clock-names: Must contain the names "ape" and "apb2ape" for the corresponding + 'clocks' entries. +- power-domains: Must contain a phandle that points to the audio powergate + (namely 'aud') for Tegra210. +- #address-cells: The number of cells used to represent physical base addresses + in the aconnect address space. Should be 1. +- #size-cells: The number of cells used to represent the size of an address + range in the aconnect address space. Should be 1. +- ranges: Mapping of the aconnect address space to the CPU address space. + +All devices accessed via the ACONNNECT are described by child-nodes. + +Example: + + aconnect@702c0000 { + compatible = "nvidia,tegra210-aconnect"; + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + clock-names = "ape", "apb2ape"; + power-domains = <&pd_audio>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x702c0000 0x0 0x702c0000 0x00040000>; + + status = "disabled"; + + child1 { + ... + }; + + child2 { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt new file mode 100644 index 000000000000..a55d31b48d6e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -0,0 +1,45 @@ +* Amlogic GXBB AO Clock and Reset Unit + +The Amlogic GXBB AO clock controller generates and supplies clock to various +controllers within the Always-On part of the SoC. + +Required Properties: + +- compatible: should be "amlogic,gxbb-aoclkc" +- reg: physical base address of the clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-aoclkc.h header and can be +used in device tree sources. + +- #reset-cells: should be 1. + +Each reset is assigned an identifier and client nodes can use this identifier +to specify the reset which they consume. All available resets are defined as +preprocessor macros in the dt-bindings/reset/gxbb-aoclkc.h header and can be +used in device tree sources. + +Example: AO Clock controller node: + + clkc_AO: clock-controller@040 { + compatible = "amlogic,gxbb-aoclkc"; + reg = <0x0 0x040 0x0 0x4>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock and reset generated + by the clock controller: + + uart_AO: serial@4c0 { + compatible = "amlogic,meson-uart"; + reg = <0x4c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc_AO CLKID_AO_UART1>; + resets = <&clkc_AO RESET_AO_UART1>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt new file mode 100644 index 000000000000..ce06435d28ed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -0,0 +1,36 @@ +* Amlogic GXBB Clock and Reset Unit + +The Amlogic GXBB clock controller generates and supplies clock to various +controllers within the SoC. + +Required Properties: + +- compatible: should be "amlogic,gxbb-clkc" +- reg: physical base address of the clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be +used in device tree sources. + +Example: Clock controller node: + + clkc: clock-controller@c883c000 { + #clock-cells = <1>; + compatible = "amlogic,gxbb-clkc"; + reg = <0x0 0xc883c000 0x0 0x3db>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart_AO: serial@c81004c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc81004c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt index 8b7177cecb36..27468119fd94 100644 --- a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -5,20 +5,50 @@ Technology (IDT). ARM integrated these oscillators deeply into their reference designs by adding special control registers that manage such oscillators to their system controllers. -The ARM system controller contains logic to serialize and initialize +The various ARM system controllers contain logic to serialize and initialize an ICST clock request after a write to the 32 bit register at an offset into the system controller. Furthermore, to even be able to alter one of these frequencies, the system controller must first be unlocked by writing a special token to another offset in the system controller. +Some ARM hardware contain special versions of the serial interface that only +connects the low 8 bits of the VDW (missing one bit), hardwires RDW to +different values and sometimes also hardwire the output divider. They +therefore have special compatible strings as per this table (the OD value is +the value on the pins, not the resulting output divider): + +Hardware variant: RDW OD VDW + +Integrator/AP 22 1 Bit 8 0, rest variable +integratorap-cm + +Integrator/AP 46 3 Bit 8 0, rest variable +integratorap-sys + +Integrator/AP 22 or 1 17 or (33 or 25 MHz) +integratorap-pci 14 1 14 + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-core + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-mem + The ICST oscillator must be provided inside a system controller node. Required properties: +- compatible: must be one of + "arm,syscon-icst525" + "arm,syscon-icst307" + "arm,syscon-icst525-integratorap-cm" + "arm,syscon-icst525-integratorap-sys" + "arm,syscon-icst525-integratorap-pci" + "arm,syscon-icst525-integratorcp-cm-core" + "arm,syscon-icst525-integratorcp-cm-mem" - lock-offset: the offset address into the system controller where the unlocking register is located - vco-offset: the offset address into the system controller where the ICST control register is located (even 32 bit address) -- compatible: must be one of "arm,syscon-icst525" or "arm,syscon-icst307" - #clock-cells: must be <0> - clocks: parent clock, since the ICST needs a parent clock to derive its frequency from, this attribute is compulsory. diff --git a/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt new file mode 100644 index 000000000000..1e3370ba189f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt @@ -0,0 +1,70 @@ +* Peripheral Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provide peripheral clocks which are +used as clock source for the peripheral of the SoC. + +There are two different blocks associated to north bridge and south +bridge. + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs for Armada 370 North bridge clocks: +ID Clock name Description +----------------------------------- +0 mmc MMC controller +1 sata_host Sata Host +2 sec_at Security AT +3 sac_dap Security DAP +4 tsecm Security Engine +5 setm_tmx Serial Embedded Trace Module +6 avs Adaptive Voltage Scaling +7 sqf SPI +8 pwm PWM +9 i2c_2 I2C 2 +10 i2c_1 I2C 1 +11 ddr_phy DDR PHY +12 ddr_fclk DDR F clock +13 trace Trace +14 counter Counter +15 eip97 EIP 97 +16 cpu CPU + +The following is a list of provided IDs for Armada 370 South bridge clocks: +ID Clock name Description +----------------------------------- +0 gbe-50 50 MHz parent clock for Gigabit Ethernet +1 gbe-core parent clock for Gigabit Ethernet core +2 gbe-125 125 MHz parent clock for Gigabit Ethernet +3 gbe1-50 50 MHz clock for Gigabit Ethernet port 1 +4 gbe0-50 50 MHz clock for Gigabit Ethernet port 0 +5 gbe1-125 125 MHz clock for Gigabit Ethernet port 1 +6 gbe0-125 125 MHz clock for Gigabit Ethernet port 0 +7 gbe1-core Gigabit Ethernet core port 1 +8 gbe0-core Gigabit Ethernet core port 0 +9 gbe-bm Gigabit Ethernet Buffer Manager +10 sdio SDIO +11 usb32-sub2-sys USB 2 clock +12 usb32-ss-sys USB 3 clock + +Required properties: + +- compatible : shall be "marvell,armada-3700-periph-clock-nb" for the + north bridge block, or + "marvell,armada-3700-periph-clock-sb" for the south bridge block +- reg : must be the register address of North/South Bridge Clock register +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks : list of the parent clock phandle in the following order: + TBG-A P, TBG-B P, TBG-A S, TBG-B S and finally the xtal clock. + + +Example: + +nb_perih_clk: nb-periph-clk@13000{ + compatible = "marvell,armada-3700-periph-clock-nb"; + reg = <0x13000 0x1000>; + clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, + <&tbg 3>, <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt new file mode 100644 index 000000000000..0ba1d83ff363 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt @@ -0,0 +1,27 @@ +* Time Base Generator Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provde Time Base Generator clocks which are +used as parent clocks for the peripheral clocks. + +The TBG clock consumer should specify the desired clock by having the +clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 3700: + 0 = TBG A P + 1 = TBG B P + 2 = TBG A S + 3 = TBG B S + +Required properties: +- compatible : shall be "marvell,armada-3700-tbg-clock" +- reg : must be the register address of North Bridge PLL register +- #clock-cells : from common clock binding; shall be set to 1 + +Example: + +tbg: tbg@13200 { + compatible = "marvell,armada-3700-tbg-clock"; + reg = <0x13200 0x1000>; + clocks = <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt new file mode 100644 index 000000000000..a88f1f05fbd6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt @@ -0,0 +1,28 @@ +* Xtal Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs allow to determine the xtal clock frequencies by +reading the gpio latch register. + +This node must be a subnode of the node exposing the register address +of the GPIO block where the gpio latch is located. + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-3700-xtal-clock" +- #clock-cells : from common clock binding; shall be set to 0 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("xtal") + +Example: +gpio1: gpio@13800 { + compatible = "marvell,armada-3700-gpio", "syscon", "simple-mfd"; + reg = <0x13800 0x1000>; + + xtalclk: xtal-clk { + compatible = "marvell,armada-3700-xtal-clock"; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/artpec6.txt b/Documentation/devicetree/bindings/clock/artpec6.txt new file mode 100644 index 000000000000..dff9cdf0009c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/artpec6.txt @@ -0,0 +1,41 @@ +* Clock bindings for Axis ARTPEC-6 chip + +The bindings are based on the clock provider binding in +Documentation/devicetree/bindings/clock/clock-bindings.txt + +External clocks: +---------------- + +There are two external inputs to the main clock controller which should be +provided using the common clock bindings. +- "sys_refclk": External 50 Mhz oscillator (required) +- "i2s_refclk": Alternate audio reference clock (optional). + +Main clock controller +--------------------- + +Required properties: +- #clock-cells: Should be <1> + See dt-bindings/clock/axis,artpec6-clkctrl.h for the list of valid identifiers. +- compatible: Should be "axis,artpec6-clkctrl" +- reg: Must contain the base address and length of the system controller +- clocks: Must contain a phandle entry for each clock in clock-names +- clock-names: Must include the external oscillator ("sys_refclk"). Optional + ones are the audio reference clock ("i2s_refclk") and the audio fractional + dividers ("frac_clk0" and "frac_clk1"). + +Examples: + +ext_clk: ext_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <50000000>; +}; + +clkctrl: clkctrl@f8000000 { + #clock-cells = <1>; + compatible = "axis,artpec6-clkctrl"; + reg = <0xf8000000 0x48>; + clocks = <&ext_clk>; + clock-names = "sys_refclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 181bc8ac4e3a..5f3ad65daf69 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -6,7 +6,8 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "atmel,at91sam9x5-sckc": + "atmel,at91sam9x5-sckc" or + "atmel,sama5d4-sckc": at91 SCKC (Slow Clock Controller) This node contains the slow clock definitions. diff --git a/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt new file mode 100644 index 000000000000..5ffc8df7e6da --- /dev/null +++ b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt @@ -0,0 +1,25 @@ +Binding for the AXS10X I2S PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "snps,axs10x-i2s-pll-clock" +- reg : address and length of the I2S PLL register set. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + pll_clock: pll_clock { + compatible = "fixed-clock"; + clock-frequency = <27000000>; + #clock-cells = <0>; + }; + + i2s_clock@100a0 { + compatible = "snps,axs10x-i2s-pll-clock"; + reg = <0x100a0 0x10>; + clocks = <&pll_clock>; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt new file mode 100644 index 000000000000..2ebb107331dd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt @@ -0,0 +1,36 @@ +Broadcom BCM53573 ILP clock +=========================== + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +This binding is used for ILP clock (sometimes referred as "slow clock") +on Broadcom BCM53573 devices using Cortex-A7 CPU. + +ILP's rate has to be calculated on runtime and it depends on ALP clock +which has to be referenced. + +This clock is part of PMU (Power Management Unit), a Broadcom's device +handing power-related aspects. Its node must be sub-node of the PMU +device. + +Required properties: +- compatible: "brcm,bcm53573-ilp" +- clocks: has to reference an ALP clock +- #clock-cells: should be <0> +- clock-output-names: from common clock bindings, should contain clock + name + +Example: + +pmu@18012000 { + compatible = "simple-mfd", "syscon"; + reg = <0x18012000 0x00001000>; + + ilp { + compatible = "brcm,bcm53573-ilp"; + clocks = <&alp>; + #clock-cells = <0>; + clock-output-names = "ilp"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt index 180e8835569e..0c3d6015868d 100644 --- a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt +++ b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt @@ -10,6 +10,8 @@ Required Properties: - "samsung,exynos4210-audss-clock" - controller compatible with all Exynos4 SoCs. - "samsung,exynos5250-audss-clock" - controller compatible with Exynos5250 SoCs. + - "samsung,exynos5410-audss-clock" - controller compatible with Exynos5410 + SoCs. - "samsung,exynos5420-audss-clock" - controller compatible with Exynos5420 SoCs. - reg: physical base address and length of the controller's register set. @@ -91,5 +93,5 @@ i2s0: i2s@03830000 { <&clock_audss EXYNOS_MOUT_AUDSS>, <&clock_audss EXYNOS_MOUT_I2S>; clock-names = "iis", "i2s_opclk0", "i2s_opclk1", - "mout_audss", "mout_i2s"; + "mout_audss", "mout_i2s"; }; diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt index ce5a7476f05d..f1bd53f79d91 100644 --- a/Documentation/devicetree/bindings/clock/clps711x-clock.txt +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -1,7 +1,7 @@ * Clock bindings for the Cirrus Logic CLPS711X CPUs Required properties: -- compatible : Shall contain "cirrus,clps711x-clk". +- compatible : Shall contain "cirrus,ep7209-clk". - reg : Address of the internal register set. - startup-frequency: Factory set CPU startup frequency in HZ. - #clock-cells : Should be <1>. @@ -13,7 +13,7 @@ for the full list of CLPS711X clock IDs. Example: clks: clks@80000000 { #clock-cells = <1>; - compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk"; + compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk"; reg = <0x80000000 0xc000>; startup-frequency = <73728000>; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt index aeab635b07b5..4527de3ea205 100644 --- a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -12,24 +12,29 @@ Required Properties: - #clock-cells: should be 1. +- clocks: should contain an entry specifying the root clock from external + oscillator supplied through XXTI or XusbXTI pin. This clock should be + defined using standard clock bindings with "fin_pll" clock-output-name. + That clock is being passed internally to the 9 PLLs. + All available clocks are defined as preprocessor macros in dt-bindings/clock/exynos5410.h header and can be used in device tree sources. -External clock: - -There is clock that is generated outside the SoC. It -is expected that it is defined using standard clock bindings -with following clock-output-name: - - - "fin_pll" - PLL input clock from XXTI - Example 1: An example of a clock controller node is listed below. + fin_pll: xxti { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + clock: clock-controller@0x10010000 { compatible = "samsung,exynos5410-clock"; reg = <0x10010000 0x30000>; #clock-cells = <1>; + clocks = <&fin_pll>; }; Example 2: UART controller node that consumes the clock generated by the clock diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt index 1bae8527eb9b..189467a7188a 100644 --- a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt +++ b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt @@ -14,6 +14,10 @@ Required properties: Optional properties: - clock-output-names : From common clock binding. +Some clocks that require special treatments are also handled by that +driver, with the compatibles: + - allwinner,sun4i-a10-pll3-2x-clk + Example: clock { compatible = "fixed-factor-clock"; diff --git a/Documentation/devicetree/bindings/clock/hi3519-crg.txt b/Documentation/devicetree/bindings/clock/hi3519-crg.txt new file mode 100644 index 000000000000..acd1f235d548 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3519-crg.txt @@ -0,0 +1,46 @@ +* Hisilicon Hi3519 Clock and Reset Generator(CRG) + +The Hi3519 CRG module provides clock and reset signals to various +controllers within the SoC. + +This binding uses the following bindings: + Documentation/devicetree/bindings/clock/clock-bindings.txt + Documentation/devicetree/bindings/reset/reset.txt + +Required Properties: + +- compatible: should be one of the following. + - "hisilicon,hi3519-crg" - controller compatible with Hi3519 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3519-clock.h>. + +- #reset-cells: should be 2. + +A reset signal can be controlled by writing a bit register in the CRG module. +The reset specifier consists of two cells. The first cell represents the +register offset relative to the base address. The second cell represents the +bit index in the register. + +Example: CRG nodes +CRG: clock-reset-controller@12010000 { + compatible = "hisilicon,hi3519-crg"; + reg = <0x12010000 0x10000>; + #clock-cells = <1>; + #reset-cells = <2>; +}; + +Example: consumer nodes +i2c0: i2c@12110000 { + compatible = "hisilicon,hi3519-i2c"; + reg = <0x12110000 0x1000>; + clocks = <&CRG HI3519_I2C0_RST>; + resets = <&CRG 0xe4 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/imx35-clock.txt b/Documentation/devicetree/bindings/clock/imx35-clock.txt index a70356452a82..f49783213c56 100644 --- a/Documentation/devicetree/bindings/clock/imx35-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx35-clock.txt @@ -94,6 +94,7 @@ clocks and IDs. csi_sel 79 iim_gate 80 gpu2d_gate 81 + ckli_gate 82 Examples: diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt index 9c40739a661a..8398a3a5e106 100644 --- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt +++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt @@ -1,10 +1,24 @@ -Binding for Maxim MAX77686 32k clock generator block +Binding for Maxim MAX77686/MAX77802/MAX77620 32k clock generator block -This is a part of device tree bindings of MAX77686 multi-function device. -More information can be found in bindings/mfd/max77686.txt file. +This is a part of device tree bindings of MAX77686/MAX77802/MAX77620 +multi-function device. More information can be found in MFD DT binding +doc as follows: + bindings/mfd/max77686.txt for MAX77686 and + bindings/mfd/max77802.txt for MAX77802 and + bindings/mfd/max77620.txt for MAX77620. The MAX77686 contains three 32.768khz clock outputs that can be controlled -(gated/ungated) over I2C. +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77686.h. + + +The MAX77802 contains two 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77802.h. + +The MAX77686 contains one 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77620.h. Following properties should be presend in main device node of the MFD chip. @@ -17,30 +31,84 @@ Optional properties: Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. Following indices are allowed: - - 0: 32khz_ap clock, - - 1: 32khz_cp clock, - - 2: 32khz_pmic clock. + - 0: 32khz_ap clock (max77686, max77802), 32khz_out0 (max77620) + - 1: 32khz_cp clock (max77686, max77802), + - 2: 32khz_pmic clock (max77686). + +Clocks are defined as preprocessor macros in above dt-binding header for +respective chips. + +Example: + +1. With MAX77686: + +#include <dt-bindings/clock/maxim,max77686.h> +/* ... */ + + Node of the MFD chip + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77686 MAX77686_CLK_PMIC>; + }; + +2. With MAX77802: + +#include <dt-bindings/clock/maxim,max77802.h> +/* ... */ + + Node of the MFD chip + max77802: max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77802 MAX77802_CLK_32K_AP>; + }; -Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h -header and can be used in device tree sources. -Example: Node of the MFD chip +3. With MAX77620: - max77686: max77686@09 { - compatible = "maxim,max77686"; - interrupt-parent = <&wakeup_eint>; - interrupts = <26 0>; - reg = <0x09>; - #clock-cells = <1>; +#include <dt-bindings/clock/maxim,max77620.h> +/* ... */ - /* ... */ - }; + Node of the MFD chip + max77620: max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + #clock-cells = <1>; + /* ... */ + }; -Example: Clock consumer node + Clock consumer node - foo@0 { - compatible = "bar,foo"; - /* ... */ - clock-names = "my-clock"; - clocks = <&max77686 MAX77686_CLK_PMIC>; - }; + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77620 MAX77620_CLK_32K_OUT0>; + }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max77802.txt b/Documentation/devicetree/bindings/clock/maxim,max77802.txt deleted file mode 100644 index c6dc7835f06c..000000000000 --- a/Documentation/devicetree/bindings/clock/maxim,max77802.txt +++ /dev/null @@ -1,44 +0,0 @@ -Binding for Maxim MAX77802 32k clock generator block - -This is a part of device tree bindings of MAX77802 multi-function device. -More information can be found in bindings/mfd/max77802.txt file. - -The MAX77802 contains two 32.768khz clock outputs that can be controlled -(gated/ungated) over I2C. - -Following properties should be present in main device node of the MFD chip. - -Required properties: -- #clock-cells: From common clock binding; shall be set to 1. - -Optional properties: -- clock-output-names: From common clock binding. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. Following indices are allowed: - - 0: 32khz_ap clock, - - 1: 32khz_cp clock. - -Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77802.h -header and can be used in device tree sources. - -Example: Node of the MFD chip - - max77802: max77802@09 { - compatible = "maxim,max77802"; - interrupt-parent = <&wakeup_eint>; - interrupts = <26 0>; - reg = <0x09>; - #clock-cells = <1>; - - /* ... */ - }; - -Example: Clock consumer node - - foo@0 { - compatible = "bar,foo"; - /* ... */ - clock-names = "my-clock"; - clocks = <&max77802 MAX77802_CLK_32K_AP>; - }; diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt new file mode 100644 index 000000000000..c93d88fdd858 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt @@ -0,0 +1,39 @@ +Microchip PIC32 Clock Controller Binding +---------------------------------------- +Microchip clock controller is consists of few oscillators, PLL, multiplexer +and few divider modules. + +This binding uses common clock bindings. +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "microchip,pic32mzda-clk". +- reg: shall contain base address and length of clock registers. +- #clock-cells: shall be 1. + +Optional properties: +- microchip,pic32mzda-sosc: shall be added only if platform has + secondary oscillator connected. + +Example: + rootclk: clock-controller@1f801200 { + compatible = "microchip,pic32mzda-clk"; + reg = <0x1f801200 0x200>; + #clock-cells = <1>; + /* optional */ + microchip,pic32mzda-sosc; + }; + + +The clock consumer shall specify the desired clock-output of the clock +controller (as defined in [2]) by specifying output-id in its "clock" +phandle cell. +[2] include/dt-bindings/clock/microchip,pic32-clock.h + +For example for UART2: +uart2: serial@2 { + compatible = "microchip,pic32mzda-uart"; + reg = <>; + interrupts = <>; + clocks = <&rootclk PB2CLK>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index 660e64912cce..cb8542d910b3 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -86,6 +86,8 @@ ID Clock Peripheral 7 pex3 PCIe 3 8 pex0 PCIe 0 9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +15 sata0 SATA 0 17 sdio SDIO 22 xor0 XOR 0 28 xor1 XOR 1 diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index ee7e5fd4a50b..63f9d8277d48 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -50,7 +50,7 @@ Required properties for I2C mode: Example: -clock@0,70110000 { +clock@70110000 { compatible = "nvidia,tegra124-dfll"; reg = <0 0x70110000 0 0x100>, /* DFLL control */ <0 0x70110000 0 0x100>, /* I2C output control */ diff --git a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt new file mode 100644 index 000000000000..208cca6ac4ec --- /dev/null +++ b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt @@ -0,0 +1,35 @@ +Oxford Semiconductor OXNAS SoC Family Standard Clocks +================================================ + +Please also refer to clock-bindings.txt in this directory for common clock +bindings usage. + +Required properties: +- compatible: Should be "oxsemi,ox810se-stdclk" +- #clock-cells: 1, see below + +Parent node should have the following properties : +- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + +For OX810SE, the clock indices are : + - 0: LEON + - 1: DMA_SGDMA + - 2: CIPHER + - 3: SATA + - 4: AUDIO + - 5: USBMPH + - 6: ETHA + - 7: PCIA + - 8: NAND + +example: + +sys: sys-ctrl@000000 { + compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"; + reg = <0x000000 0x100000>; + + stdclk: stdclk { + compatible = "oxsemi,ox810se-stdclk"; + #clock-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 9a60fde32b02..869a2f0e2ff6 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -15,6 +15,7 @@ Required properties : "qcom,gcc-msm8974pro" "qcom,gcc-msm8974pro-ac" "qcom,gcc-msm8996" + "qcom,gcc-mdm9615" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,lcc.txt b/Documentation/devicetree/bindings/clock/qcom,lcc.txt index dd755be63a01..a3c78aa88038 100644 --- a/Documentation/devicetree/bindings/clock/qcom,lcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,lcc.txt @@ -7,6 +7,7 @@ Required properties : "qcom,lcc-msm8960" "qcom,lcc-apq8064" "qcom,lcc-ipq8064" + "qcom,lcc-mdm9615" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index fefb8023020f..394d725ac7e0 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -13,7 +13,8 @@ They provide the following functionalities: Required Properties: - compatible: Must be one of: - - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC + - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) + - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) - reg: Base address and length of the memory resource used by the CPG/MSSR block @@ -21,8 +22,8 @@ Required Properties: - clocks: References to external parent clocks, one entry for each entry in clock-names - clock-names: List of external parent clock names. Valid names are: - - "extal" (r8a7795) - - "extalr" (r8a7795) + - "extal" (r8a7795, r8a7796) + - "extalr" (r8a7795, r8a7796) - #clock-cells: Must be 2 - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 16ed18155160..da578ebdda28 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -17,6 +17,7 @@ Required Properties: - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2-W) MSTP gate clocks + - "renesas,r8a7792-mstp-clocks" for R8A7792 (R-Car V2H) MSTP gate clocks - "renesas,r8a7793-mstp-clocks" for R8A7793 (R-Car M2-N) MSTP gate clocks - "renesas,r8a7794-mstp-clocks" for R8A7794 (R-Car E2) MSTP gate clocks - "renesas,sh73a0-mstp-clocks" for SH73A0 (SH-MobileAG5) MSTP gate clocks diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index 2a9a8edc8f35..f8c05bb4116e 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -10,6 +10,7 @@ Required Properties: - compatible: Must be one of - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7792-cpg-clocks" for the r8a7792 CPG - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG and "renesas,rcar-gen2-cpg-clocks" as a fallback. diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt index 0c2bf5eba43e..7f368530a2e4 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -16,7 +16,7 @@ Required Properties: Optional Properties: - rockchip,grf: phandle to the syscon managing the "general register files" - If missing pll rates are not changable, due to the missing pll lock status. + If missing pll rates are not changeable, due to the missing pll lock status. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt index c9fbb76573e1..8cb47c39ba53 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -15,7 +15,7 @@ Required Properties: Optional Properties: - rockchip,grf: phandle to the syscon managing the "general register files" - If missing pll rates are not changable, due to the missing pll lock status. + If missing pll rates are not changeable, due to the missing pll lock status. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt new file mode 100644 index 000000000000..3888dd33fcbd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt @@ -0,0 +1,62 @@ +* Rockchip RK3399 Clock and Reset Unit + +The RK3399 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: PMU for CRU should be "rockchip,rk3399-pmucru" +- compatible: CRU should be "rockchip,rk3399-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "clkin_gmac" - external GMAC clock - optional, + - "clkin_i2s" - external I2S clock - optional, + - "pclkin_cif" - external ISP clock - optional, + - "clk_usbphy0_480m" - output clock of the pll in the usbphy0 + - "clk_usbphy1_480m" - output clock of the pll in the usbphy1 + +Example: Clock controller node: + + pmucru: pmu-clock-controller@ff750000 { + compatible = "rockchip,rk3399-pmucru"; + reg = <0x0 0xff750000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3399-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff1a0000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff180000 0x0 0x100>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt deleted file mode 100644 index 6247652044a0..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt +++ /dev/null @@ -1,49 +0,0 @@ -Binding for a ST divider and multiplexer clock driver. - -This binding uses the common clock binding[1]. -Base address is located to the parent node. See clock binding[2] - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt - -Required properties: - -- compatible : shall be: - "st,clkgena-divmux-c65-hs", "st,clkgena-divmux" - "st,clkgena-divmux-c65-ls", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf0", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf2", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf3", "st,clkgena-divmux" - -- #clock-cells : From common clock binding; shall be set to 1. - -- clocks : From common clock binding - -- clock-output-names : From common clock binding. - -Example: - - clockgen-a@fd345000 { - reg = <0xfd345000 0xb50>; - - clk_m_a1_div1: clk-m-a1-div1 { - #clock-cells = <1>; - compatible = "st,clkgena-divmux-c32-odf1", - "st,clkgena-divmux"; - - clocks = <&clk_m_a1_osc_prediv>, - <&clk_m_a1_pll0 1>, /* PLL0 PHI1 */ - <&clk_m_a1_pll1 1>; /* PLL1 PHI1 */ - - clock-output-names = "clk-m-rx-icn-ts", - "clk-m-rx-icn-vdp-0", - "", /* unused */ - "clk-m-prv-t1-bus", - "clk-m-icn-reg-12", - "clk-m-icn-reg-10", - "", /* unused */ - "clk-m-icn-st231"; - }; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt index f1fa91c68768..9a46cb1d7a04 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -10,14 +10,7 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be: - "st,stih416-clkgenc-vcc-hd", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-fvdp", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-hd", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" - "st,stih415-clkgen-a9-mux", "st,clkgen-mux" - "st,stih416-clkgen-a9-mux", "st,clkgen-mux" - "st,stih407-clkgen-a9-mux", "st,clkgen-mux" + "st,stih407-clkgen-a9-mux" - #clock-cells : from common clock binding; shall be set to 0. @@ -27,10 +20,13 @@ Required properties: Example: - clk_m_hva: clk-m-hva@fd690868 { + clk_m_a9: clk-m-a9@92b0000 { #clock-cells = <0>; - compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; - reg = <0xfd690868 4>; + compatible = "st,stih407-clkgen-a9-mux"; + reg = <0x92b0000 0x10000>; - clocks = <&clockgen_f 1>, <&clk_m_a1_div0 3>; + clocks = <&clockgen_a9_pll 0>, + <&clockgen_a9_pll 0>, + <&clk_s_c0_flexgen 13>, + <&clk_m_a9_ext2f_div2>; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index 844b3a0976bf..f207053e0550 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -9,24 +9,10 @@ Base address is located to the parent node. See clock binding[2] Required properties: - compatible : shall be: - "st,clkgena-prediv-c65", "st,clkgena-prediv" - "st,clkgena-prediv-c32", "st,clkgena-prediv" - - "st,clkgena-plls-c65" - "st,plls-c32-a1x-0", "st,clkgen-plls-c32" - "st,plls-c32-a1x-1", "st,clkgen-plls-c32" - "st,stih415-plls-c32-a9", "st,clkgen-plls-c32" - "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" - "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" - "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" - "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" - "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" - "sst,plls-c32-cx_0", "st,clkgen-plls-c32" - "sst,plls-c32-cx_1", "st,clkgen-plls-c32" - "st,stih418-plls-c28-a9", "st,clkgen-plls-c32" - - "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" - "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" + "st,clkgen-pll0" + "st,clkgen-pll1" + "st,stih407-clkgen-plla9" + "st,stih418-clkgen-plla9" - #clock-cells : From common clock binding; shall be set to 1. @@ -36,17 +22,16 @@ Required properties: Example: - clockgen-a@fee62000 { - reg = <0xfee62000 0xb48>; + clockgen-a9@92b0000 { + compatible = "st,clkgen-c32"; + reg = <0x92b0000 0xffff>; - clk_s_a0_pll: clk-s-a0-pll { + clockgen_a9_pll: clockgen-a9-pll { #clock-cells = <1>; - compatible = "st,clkgena-plls-c65"; + compatible = "st,stih407-clkgen-plla9"; clocks = <&clk_sysin>; - clock-output-names = "clk-s-a0-pll0-hs", - "clk-s-a0-pll0-ls", - "clk-s-a0-pll1"; + clock-output-names = "clockgen-a9-pll-odf"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt deleted file mode 100644 index 604766c2619e..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt +++ /dev/null @@ -1,36 +0,0 @@ -Binding for a ST pre-divider clock driver. - -This binding uses the common clock binding[1]. -Base address is located to the parent node. See clock binding[2] - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt - -Required properties: - -- compatible : shall be: - "st,clkgena-prediv-c65", "st,clkgena-prediv" - "st,clkgena-prediv-c32", "st,clkgena-prediv" - -- #clock-cells : From common clock binding; shall be set to 0. - -- clocks : From common clock binding - -- clock-output-names : From common clock binding. - -Example: - - clockgen-a@fd345000 { - reg = <0xfd345000 0xb50>; - - clk_m_a2_osc_prediv: clk-m-a2-osc-prediv { - #clock-cells = <0>; - compatible = "st,clkgena-prediv-c32", - "st,clkgena-prediv"; - - clocks = <&clk_sysin>; - - clock-output-names = "clk-m-a2-osc-prediv"; - }; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt deleted file mode 100644 index 109b3eddcb17..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt +++ /dev/null @@ -1,61 +0,0 @@ -Binding for a type of STMicroelectronics clock crossbar (VCC). - -The crossbar can take up to 4 input clocks and control up to 16 -output clocks. Not all inputs or outputs have to be in use in a -particular instantiation. Each output can be individually enabled, -select any of the input clocks and apply a divide (by 1,2,4 or 8) to -that selected clock. - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -Required properties: - -- compatible : shall be: - "st,stih416-clkgenc", "st,vcc" - "st,stih416-clkgenf", "st,vcc" - -- #clock-cells : from common clock binding; shall be set to 1. - -- reg : A Base address and length of the register set. - -- clocks : from common clock binding - -- clock-output-names : From common clock binding. The block has 16 - clock outputs but not all of them in a specific instance - have to be used in the SoC. If a clock name is left as - an empty string then no clock will be created for the - output associated with that string index. If fewer than - 16 strings are provided then no clocks will be created - for the remaining outputs. - -Example: - - clockgen_c_vcc: clockgen-c-vcc@0xfe8308ac { - #clock-cells = <1>; - compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; - reg = <0xfe8308ac 12>; - - clocks = <&clk_s_vcc_hd>, - <&clockgen_c 1>, - <&clk_s_tmds_fromphy>, - <&clockgen_c 2>; - - clock-output-names = "clk-s-pix-hdmi", - "clk-s-pix-dvo", - "clk-s-out-dvo", - "clk-s-pix-hd", - "clk-s-hddac", - "clk-s-denc", - "clk-s-sddac", - "clk-s-pix-main", - "clk-s-pix-aux", - "clk-s-stfe-frc-0", - "clk-s-ref-mcru", - "clk-s-slave-mcru", - "clk-s-tmds-hdmi", - "clk-s-hdmi-reject-pll", - "clk-s-thsens"; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index 78978f1f5158..c35390f60545 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -13,14 +13,6 @@ address is common of all subnode. ... }; - prediv_node { - ... - }; - - divmux_node { - ... - }; - quadfs_node { ... }; @@ -29,10 +21,6 @@ address is common of all subnode. ... }; - vcc_node { - ... - }; - flexgen_node { ... }; @@ -40,14 +28,11 @@ address is common of all subnode. }; This binding uses the common clock binding[1]. -Each subnode should use the binding discribe in [2]..[7] +Each subnode should use the binding described in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt [3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt [4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt -[5] Documentation/devicetree/bindings/clock/st,clkgen-prediv.txt -[6] Documentation/devicetree/bindings/clock/st,vcc.txt [7] Documentation/devicetree/bindings/clock/st,quadfs.txt [8] Documentation/devicetree/bindings/clock/st,flexgen.txt @@ -57,44 +42,27 @@ Required properties: Example: - clockgen-a@fee62000 { - - reg = <0xfee62000 0xb48>; + clockgen-a@090ff000 { + compatible = "st,clkgen-c32"; + reg = <0x90ff000 0x1000>; clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; - compatible = "st,clkgena-plls-c65"; - - clocks = <&clk-sysin>; - - clock-output-names = "clk-s-a0-pll0-hs", - "clk-s-a0-pll0-ls", - "clk-s-a0-pll1"; - }; - - clk_s_a0_osc_prediv: clk-s-a0-osc-prediv { - #clock-cells = <0>; - compatible = "st,clkgena-prediv-c65", - "st,clkgena-prediv"; + compatible = "st,clkgen-pll0"; clocks = <&clk_sysin>; - clock-output-names = "clk-s-a0-osc-prediv"; + clock-output-names = "clk-s-a0-pll-ofd-0"; }; - clk_s_a0_hs: clk-s-a0-hs { + clk_s_a0_flexgen: clk-s-a0-flexgen { + compatible = "st,flexgen"; + #clock-cells = <1>; - compatible = "st,clkgena-divmux-c65-hs", - "st,clkgena-divmux"; - clocks = <&clk-s_a0_osc_prediv>, - <&clk-s_a0_pll 0>, /* pll0 hs */ - <&clk-s_a0_pll 2>; /* pll1 */ + clocks = <&clk_s_a0_pll 0>, + <&clk_sysin>; - clock-output-names = "clk-s-fdma-0", - "clk-s-fdma-1", - ""; /* clk-s-jit-sense */ - /* fourth output unused */ + clock-output-names = "clk-ic-lmi0"; }; }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt index b7ee5c7e0f75..7ff77fc57dff 100644 --- a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -60,6 +60,10 @@ This binding uses the common clock binding[2]. Required properties: - compatible : shall be: "st,flexgen" + "st,flexgen-audio", "st,flexgen" (enable clock propagation on parent for + audio use case) + "st,flexgen-video", "st,flexgen" (enable clock propagation on parent + and activate synchronous mode) - #clock-cells : from common clock binding; shall be set to 1 (multiple clock outputs). diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt index cedeb9cc8208..d93d49342e60 100644 --- a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -11,12 +11,8 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be: - "st,stih416-quadfs216", "st,quadfs" - "st,stih416-quadfs432", "st,quadfs" - "st,stih416-quadfs660-E", "st,quadfs" - "st,stih416-quadfs660-F", "st,quadfs" - "st,stih407-quadfs660-C", "st,quadfs" - "st,stih407-quadfs660-D", "st,quadfs" + "st,quadfs" + "st,quadfs-pll" - #clock-cells : from common clock binding; shall be set to 1. @@ -35,14 +31,15 @@ Required properties: Example: - clockgen_e: clockgen-e@fd3208bc { - #clock-cells = <1>; - compatible = "st,stih416-quadfs660-E", "st,quadfs"; - reg = <0xfd3208bc 0xB0>; - - clocks = <&clk_sysin>; - clock-output-names = "clk-m-pix-mdtp-0", - "clk-m-pix-mdtp-1", - "clk-m-pix-mdtp-2", - "clk-m-mpelpc"; - }; + clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 { + #clock-cells = <1>; + compatible = "st,quadfs-pll"; + reg = <0x9103000 0x1000>; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-c0-fs0-ch0", + "clk-s-c0-fs0-ch1", + "clk-s-c0-fs0-ch2", + "clk-s-c0-fs0-ch3"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt new file mode 100644 index 000000000000..3868458a5feb --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -0,0 +1,27 @@ +Allwinner Clock Control Unit Binding +------------------------------------ + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun6i-a31-ccu" + - "allwinner,sun8i-a23-ccu" + - "allwinner,sun8i-a33-ccu" + - "allwinner,sun8i-h3-ccu" + +- reg: Must contain the registers base address and length +- clocks: phandle to the oscillators feeding the CCU. Two are needed: + - "hosc": the high frequency oscillator (usually at 24MHz) + - "losc": the low frequency oscillator (usually at 32kHz) +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +ccu: clock@01c20000 { + compatible = "allwinner,sun8i-h3-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 834436fbe83d..8f7619d8c8d8 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -10,6 +10,7 @@ Required properties: "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 + "allwinner,sun4i-a10-pll3-clk" - for the video PLL clock on A10 "allwinner,sun9i-a80-pll4-clk" - for the peripheral PLLs on A80 "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock @@ -63,7 +64,9 @@ Required properties: "allwinner,sun8i-a83t-bus-gates-clk" - for the bus gates on A83T "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3 "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80 + "allwinner,sun4i-a10-display-clk" - for the display clocks on the A10 "allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10 + "allwinner,sun5i-a13-dram-gates-clk" - for the DRAM gates on A13 "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 "allwinner,sun4i-a10-mmc-clk" - for the MMC clock "allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80 @@ -73,6 +76,8 @@ Required properties: "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 + "allwinner,sun4i-a10-tcon-ch0-clk" - for the TCON channel 0 clock on the A10 + "allwinner,sun4i-a10-tcon-ch1-clk" - for the TCON channel 1 clock on the A10 "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 @@ -81,6 +86,7 @@ Required properties: "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock + "allwinner,sun6i-a31-display-clk" - for the display clocks Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt new file mode 100644 index 000000000000..c7179d3b5c33 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -0,0 +1,134 @@ +UniPhier clock controller + + +System clock +------------ + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-clock" - for LD4 SoC. + "socionext,uniphier-pro4-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-clock" - for LD11 SoC. + "socionext,uniphier-ld20-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + clock { + compatible = "socionext,uniphier-ld20-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 8: ST DMAC +12: GIO (Giga bit stream I/O) +14: USB3 ch0 host +15: USB3 ch1 host +16: USB3 ch0 PHY0 +17: USB3 ch0 PHY1 +20: USB3 ch1 PHY0 +21: USB3 ch1 PHY1 + + +Media I/O (MIO) clock +--------------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-mio-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. + "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-mio-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-mio-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. + "socionext,uniphier-ld20-mio-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + mioctrl@59810000 { + compatible = "socionext,uniphier-mioctrl", + "simple-mfd", "syscon"; + reg = <0x59810000 0x800>; + + clock { + compatible = "socionext,uniphier-ld20-mio-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: SD ch0 host + 1: eMMC host + 2: SD ch1 host + 7: MIO DMAC + 8: USB2 ch0 host + 9: USB2 ch1 host +10: USB2 ch2 host +11: USB2 ch3 host +12: USB2 ch0 PHY +13: USB2 ch1 PHY +14: USB2 ch2 PHY +15: USB2 ch3 PHY + + +Peripheral clock +---------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-peri-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-peri-clock" - for LD4 SoC. + "socionext,uniphier-pro4-peri-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-peri-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-peri-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-peri-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-peri-clock" - for LD11 SoC. + "socionext,uniphier-ld20-peri-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + perictrl@59820000 { + compatible = "socionext,uniphier-perictrl", + "simple-mfd", "syscon"; + reg = <0x59820000 0x200>; + + clock { + compatible = "socionext,uniphier-ld20-peri-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: UART ch0 + 1: UART ch1 + 2: UART ch2 + 3: UART ch3 + 4: I2C ch0 + 5: I2C ch1 + 6: I2C ch2 + 7: I2C ch3 + 8: I2C ch4 + 9: I2C ch5 +10: I2C ch6 diff --git a/Documentation/devicetree/bindings/clock/xgene.txt b/Documentation/devicetree/bindings/clock/xgene.txt index 82f9638121db..8233e771711b 100644 --- a/Documentation/devicetree/bindings/clock/xgene.txt +++ b/Documentation/devicetree/bindings/clock/xgene.txt @@ -8,6 +8,7 @@ Required properties: - compatible : shall be one of the following: "apm,xgene-socpll-clock" - for a X-Gene SoC PLL clock "apm,xgene-pcppll-clock" - for a X-Gene PCP PLL clock + "apm,xgene-pmd-clock" - for a X-Gene PMD clock "apm,xgene-device-clock" - for a X-Gene device clock "apm,xgene-socpll-v2-clock" - for a X-Gene SoC PLL v2 clock "apm,xgene-pcppll-v2-clock" - for a X-Gene PCP PLL v2 clock @@ -22,6 +23,15 @@ Required properties for SoC or PCP PLL clocks: Optional properties for PLL clocks: - clock-names : shall be the name of the PLL. If missing, use the device name. +Required properties for PMD clocks: +- reg : shall be the physical register address for the pmd clock. +- clocks : shall be the input parent clock phandle for the clock. +- #clock-cells : shall be set to 1. +- clock-output-names : shall be the name of the clock referenced by derive + clock. +Optional properties for PLL clocks: +- clock-names : shall be the name of the clock. If missing, use the device name. + Required properties for device clocks: - reg : shall be a list of address and length pairs describing the CSR reset and/or the divider. Either may be omitted, but at least @@ -59,6 +69,14 @@ For example: type = <0>; }; + pmd0clk: pmd0clk@7e200200 { + compatible = "apm,xgene-pmd-clock"; + #clock-cells = <1>; + clocks = <&pmdpll 0>; + reg = <0x0 0x7e200200 0x0 0x10>; + clock-output-names = "pmd0clk"; + }; + socpll: socpll@17000120 { compatible = "apm,xgene-socpll-clock"; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt new file mode 100644 index 000000000000..8c18b7b237bf --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -0,0 +1,35 @@ +Device Tree Clock bindings for ZTE zx296718 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "zte,zx296718-topcrm": + zx296718 top clock selection, divider and gating + + "zte,zx296718-lsp0crm" and + "zte,zx296718-lsp1crm": + zx296718 device level clock selection and gating + +- reg: Address and length of the register set + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296718-clock.h +for the full list of zx296718 clock IDs. + + +topclk: topcrm@1461000 { + compatible = "zte,zx296718-topcrm-clk"; + reg = <0x01461000 0x1000>; + #clock-cells = <1>; +}; + +usbphy0:usb-phy0 { + compatible = "zte,zx296718-usb-phy"; + #phy-cells = <0>; + clocks = <&topclk USB20_PHY_CLK>; + clock-names = "phyclk"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt index b1669fbfb740..b1669fbfb740 100644 --- a/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt +++ b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt diff --git a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt new file mode 100644 index 000000000000..f2233138eba9 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt @@ -0,0 +1,19 @@ + +* Rockchip rk3399 DFI device + +Required properties: +- compatible: Must be "rockchip,rk3399-dfi". +- reg: physical base address of each DFI and length of memory mapped region +- rockchip,pmu: phandle to the syscon managing the "pmu general register files" +- clocks: phandles for clock specified in "clock-names" property +- clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon"; + +Example: + dfi: dfi@0xff630000 { + compatible = "rockchip,rk3399-dfi"; + reg = <0x00 0xff630000 0x00 0x4000>; + rockchip,pmu = <&pmugrf>; + clocks = <&cru PCLK_DDR_MON>; + clock-names = "pclk_ddr_mon"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt new file mode 100644 index 000000000000..7a9e8603c150 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -0,0 +1,209 @@ +* Rockchip rk3399 DMC(Dynamic Memory Controller) device + +Required properties: +- compatible: Must be "rockchip,rk3399-dmc". +- devfreq-events: Node to get DDR loading, Refer to + Documentation/devicetree/bindings/devfreq/ + rockchip-dfi.txt +- interrupts: The interrupt number to the CPU. The interrupt + specifier format depends on the interrupt controller. + It should be DCF interrupts, when DDR dvfs finish, + it will happen. +- clocks: Phandles for clock specified in "clock-names" property +- clock-names : The name of clock used by the DFI, must be + "pclk_ddr_mon"; +- operating-points-v2: Refer to Documentation/devicetree/bindings/power/opp.txt + for details. +- center-supply: DMC supply node. +- status: Marks the node enabled/disabled. + +Following properties are ddr timing: + +- rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/ddr.h, + it select ddr3 cl-trp-trcd type, default value + "DDR3_DEFAULT".it must selected according to + "Speed Bin" in ddr3 datasheet, DO NOT use + smaller "Speed Bin" than ddr3 exactly is. + +- rockchip,pd_idle : Config the PD_IDLE value, defined the power-down + idle period, memories are places into power-down + mode if bus is idle for PD_IDLE DFI clocks. + +- rockchip,sr_idle : Configure the SR_IDLE value, defined the + selfrefresh idle period, memories are places + into self-refresh mode if bus is idle for + SR_IDLE*1024 DFI clocks (DFI clocks freq is + half of dram's clocks), defaule value is "0". + +- rockchip,sr_mc_gate_idle : Defined the self-refresh with memory and + controller clock gating idle period, memories + are places into self-refresh mode and memory + controller clock arg gating if bus is idle for + sr_mc_gate_idle*1024 DFI clocks. + +- rockchip,srpd_lite_idle : Defined the self-refresh power down idle + period, memories are places into self-refresh + power down mode if bus is idle for + srpd_lite_idle*1024 DFI clocks. This parameter + is for LPDDR4 only. + +- rockchip,standby_idle : Defined the standby idle period, memories are + places into self-refresh than controller, pi, + phy and dram clock will gating if bus is idle + for standby_idle * DFI clocks. + +- rockchip,dram_dll_disb_freq : It's defined the DDR3 dll bypass frequency in + MHz, when ddr freq less than DRAM_DLL_DISB_FREQ, + ddr3 dll will bypssed note: if dll was bypassed, + the odt also stop working. + +- rockchip,phy_dll_disb_freq : Defined the PHY dll bypass frequency in + MHz (Mega Hz), when ddr freq less than + DRAM_DLL_DISB_FREQ, phy dll will bypssed. + note: phy dll and phy odt are independent. + +- rockchip,ddr3_odt_disb_freq : When dram type is DDR3, this parameter defined + the odt disable frequency in MHz (Mega Hz), + when ddr frequency less then ddr3_odt_disb_freq, + the odt on dram side and controller side are + both disabled. + +- rockchip,ddr3_drv : When dram type is DDR3, this parameter define + the dram side driver stength in ohm, default + value is DDR3_DS_40ohm. + +- rockchip,ddr3_odt : When dram type is DDR3, this parameter define + the dram side ODT stength in ohm, default value + is DDR3_ODT_120ohm. + +- rockchip,phy_ddr3_ca_drv : When dram type is DDR3, this parameter define + the phy side CA line(incluing command line, + address line and clock line) driver strength. + Default value is PHY_DRV_ODT_40. + +- rockchip,phy_ddr3_dq_drv : When dram type is DDR3, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is PHY_DRV_ODT_40. + +- rockchip,phy_ddr3_odt : When dram type is DDR3, this parameter define the + phy side odt strength, default value is + PHY_DRV_ODT_240. + +- rockchip,lpddr3_odt_disb_freq : When dram type is LPDDR3, this parameter defined + then odt disable frequency in MHz (Mega Hz), + when ddr frequency less then ddr3_odt_disb_freq, + the odt on dram side and controller side are + both disabled. + +- rockchip,lpddr3_drv : When dram type is LPDDR3, this parameter define + the dram side driver stength in ohm, default + value is LP3_DS_34ohm. + +- rockchip,lpddr3_odt : When dram type is LPDDR3, this parameter define + the dram side ODT stength in ohm, default value + is LP3_ODT_240ohm. + +- rockchip,phy_lpddr3_ca_drv : When dram type is LPDDR3, this parameter define + the phy side CA line(incluing command line, + address line and clock line) driver strength. + default value is PHY_DRV_ODT_40. + +- rockchip,phy_lpddr3_dq_drv : When dram type is LPDDR3, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is + PHY_DRV_ODT_40. + +- rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define + the phy side odt strength, default value is + PHY_DRV_ODT_240. + +- rockchip,lpddr4_odt_disb_freq : When dram type is LPDDR4, this parameter + defined the odt disable frequency in + MHz (Mega Hz), when ddr frequency less then + ddr3_odt_disb_freq, the odt on dram side and + controller side are both disabled. + +- rockchip,lpddr4_drv : When dram type is LPDDR4, this parameter define + the dram side driver stength in ohm, default + value is LP4_PDDS_60ohm. + +- rockchip,lpddr4_dq_odt : When dram type is LPDDR4, this parameter define + the dram side ODT on dqs/dq line stength in ohm, + default value is LP4_DQ_ODT_40ohm. + +- rockchip,lpddr4_ca_odt : When dram type is LPDDR4, this parameter define + the dram side ODT on ca line stength in ohm, + default value is LP4_CA_ODT_40ohm. + +- rockchip,phy_lpddr4_ca_drv : When dram type is LPDDR4, this parameter define + the phy side CA line(incluing command address + line) driver strength. default value is + PHY_DRV_ODT_40. + +- rockchip,phy_lpddr4_ck_cs_drv : When dram type is LPDDR4, this parameter define + the phy side clock line and cs line driver + strength. default value is PHY_DRV_ODT_80. + +- rockchip,phy_lpddr4_dq_drv : When dram type is LPDDR4, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is PHY_DRV_ODT_80. + +- rockchip,phy_lpddr4_odt : When dram type is LPDDR4, this parameter define + the phy side odt strength, default value is + PHY_DRV_ODT_60. + +Example: + dmc_opp_table: dmc_opp_table { + compatible = "operating-points-v2"; + + opp00 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <900000>; + }; + opp01 { + opp-hz = /bits/ 64 <666000000>; + opp-microvolt = <900000>; + }; + }; + + dmc: dmc { + compatible = "rockchip,rk3399-dmc"; + devfreq-events = <&dfi>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_DDRCLK>; + clock-names = "dmc_clk"; + operating-points-v2 = <&dmc_opp_table>; + center-supply = <&ppvar_centerlogic>; + upthreshold = <15>; + downdifferential = <10>; + rockchip,ddr3_speed_bin = <21>; + rockchip,pd_idle = <0x40>; + rockchip,sr_idle = <0x2>; + rockchip,sr_mc_gate_idle = <0x3>; + rockchip,srpd_lite_idle = <0x4>; + rockchip,standby_idle = <0x2000>; + rockchip,dram_dll_dis_freq = <300>; + rockchip,phy_dll_dis_freq = <125>; + rockchip,auto_pd_dis_freq = <666>; + rockchip,ddr3_odt_dis_freq = <333>; + rockchip,ddr3_drv = <DDR3_DS_40ohm>; + rockchip,ddr3_odt = <DDR3_ODT_120ohm>; + rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>; + rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>; + rockchip,lpddr3_odt_dis_freq = <333>; + rockchip,lpddr3_drv = <LP3_DS_34ohm>; + rockchip,lpddr3_odt = <LP3_ODT_240ohm>; + rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>; + rockchip,lpddr4_odt_dis_freq = <333>; + rockchip,lpddr4_drv = <LP4_PDDS_60ohm>; + rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>; + rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>; + rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>; + rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>; + rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/display/arm,malidp.txt b/Documentation/devicetree/bindings/display/arm,malidp.txt new file mode 100644 index 000000000000..2f7870983ef1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,malidp.txt @@ -0,0 +1,65 @@ +ARM Mali-DP + +The following bindings apply to a family of Display Processors sold as +licensable IP by ARM Ltd. The bindings describe the Mali DP500, DP550 and +DP650 processors that offer multiple composition layers, support for +rotation and scaling output. + +Required properties: + - compatible: should be one of + "arm,mali-dp500" + "arm,mali-dp550" + "arm,mali-dp650" + depending on the particular implementation present in the hardware + - reg: Physical base address and size of the block of registers used by + the processor. + - interrupts: Interrupt list, as defined in ../interrupt-controller/interrupts.txt, + interrupt client nodes. + - interrupt-names: name of the engine inside the processor that will + use the corresponding interrupt. Should be one of "DE" or "SE". + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. It should contain: + - "pclk": for the APB interface clock + - "aclk": for the AXI interface clock + - "mclk": for the main processor clock + - "pxlclk": for the pixel clock feeding the output PLL of the processor. + - arm,malidp-output-port-lines: Array of u8 values describing the number + of output lines per channel (R, G and B). + +Required sub-nodes: + - port: The Mali DP connection to an encoder input port. The connection + is modelled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer may + be located anywhere in memory. + + +Example: + +/ { + ... + + dp0: malidp@6f200000 { + compatible = "arm,mali-dp650"; + reg = <0 0x6f200000 0 0x20000>; + memory-region = <&display_reserved>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>, + <0 168 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "DE", "SE"; + clocks = <&oscclk2>, <&fpgaosc0>, <&fpgaosc1>, <&fpgaosc1>; + clock-names = "pxlclk", "mclk", "aclk", "pclk"; + arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + port { + dp0_output: endpoint { + remote-endpoint = <&tda998x_2_input>; + }; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index 9f97df4d5152..a5ea451e67fc 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -35,12 +35,22 @@ Optional properties for HDMI: as an interrupt/status bit in the HDMI controller itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt +Required properties for DPI: +- compatible: Should be "brcm,bcm2835-dpi" +- reg: Physical base address and length of the registers +- clocks: a) core: The core clock the unit runs on + b) pixel: The pixel clock that feeds the pixelvalve +- port: Port node with a single endpoint connecting to the panel + device, as defined in [1] + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers - interrupts: The interrupt number See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +[1] Documentation/devicetree/bindings/media/video-interfaces.txt + Example: pixelvalve@7e807000 { compatible = "brcm,bcm2835-pixelvalve2"; @@ -66,6 +76,22 @@ hdmi: hdmi@7e902000 { clock-names = "pixel", "hdmi"; }; +dpi: dpi@7e208000 { + compatible = "brcm,bcm2835-dpi"; + reg = <0x7e208000 0x8c>; + clocks = <&clocks BCM2835_CLOCK_VPU>, + <&clocks BCM2835_CLOCK_DPI>; + clock-names = "core", "pixel"; + #address-cells = <1>; + #size-cells = <0>; + + port { + dpi_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; @@ -75,3 +101,13 @@ v3d: v3d@7ec00000 { vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; + +panel: panel { + compatible = "ontat,yx700wv03", "simple-panel"; + + port { + panel_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 96c25ee01501..6532a59c9b43 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -1,13 +1,19 @@ -Analog Device ADV7511(W)/13 HDMI Encoders +Analog Device ADV7511(W)/13/33 HDMI Encoders ----------------------------------------- -The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, -S/PDIF, CEC and HDCP. +S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while +the others support RGB interface. Required properties: -- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- compatible: Should be one of: + "adi,adv7511" + "adi,adv7511w" + "adi,adv7513" + "adi,adv7533" + - reg: I2C slave address The ADV7511 supports a large number of input data formats that differ by their @@ -32,6 +38,11 @@ The following input format properties are required except in "rgb 1x" and - adi,input-justification: The input bit justification ("left", "evenly", "right"). +The following properties are required for ADV7533: + +- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + Optional properties: - interrupts: Specifier for the ADV7511 interrupt @@ -42,13 +53,18 @@ Optional properties: - adi,embedded-sync: The input uses synchronization signals embedded in the data stream (similar to BT.656). Defaults to separate H/V synchronization signals. +- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing + generator. The chip will rely on the sync signals in the DSI data lanes, + rather than generate its own timings for HDMI output. Required nodes: The ADV7511 has two video ports. Their connections are modelled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. -- Video port 0 for the RGB or YUV input +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the + remote endpoint phandle should be a reference to a valid mipi_dsi_host device + node. - Video port 1 for the HDMI output diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt new file mode 100644 index 000000000000..4a0f4f7682ad --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt @@ -0,0 +1,53 @@ +Analogix Display Port bridge bindings + +Required properties for dp-controller: + -compatible: + platform specific such as: + * "samsung,exynos5-dp" + * "rockchip,rk3288-dp" + * "rockchip,rk3399-edp" + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -interrupt-parent: + phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + +Optional properties for dp-controller: + -force-hpd: + Indicate driver need force hpd when hpd detect failed, this + is used for some eDP screen which don't have hpd signal. + -hpd-gpios: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug detection + -port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/display/exynos/exynos_dp.txt + * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt +------------------------------------------------------------------------------- + +Example: + + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt new file mode 100644 index 000000000000..56a3e68ccb80 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -0,0 +1,35 @@ +sii902x HDMI bridge bindings + +Required properties: + - compatible: "sil,sii9022" + - reg: i2c address of the bridge + +Optional properties: + - interrupts-extended or interrupt-parent + interrupts: describe + the interrupt line used to inform the host about hotplug events. + - reset-gpios: OF device-tree gpio specification for RST_N pin. + +Optional subnodes: + - video input: this subnode can contain a video input port node + to connect the bridge to a display controller output (See this + documentation [1]). + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + hdmi-bridge@39 { + compatible = "sil,sii9022"; + reg = <0x39>; + reset-gpios = <&pioA 1 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dc_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt new file mode 100644 index 000000000000..e3f6aa6a214d --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt @@ -0,0 +1,53 @@ +Toshiba TC358767 eDP bridge bindings + +Required properties: + - compatible: "toshiba,tc358767" + - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins + - clock-names: should be "ref" + - clocks: OF device-tree clock specification for refclk input. The reference + clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz. + +Optional properties: + - shutdown-gpios: OF device-tree gpio specification for SD pin + (active high shutdown input) + - reset-gpios: OF device-tree gpio specification for RSTX pin + (active low system reset) + - ports: the ports node can contain video interface port nodes to connect + to a DPI/DSI source and to an eDP/DP sink according to [1][2]: + - port@0: DSI input port + - port@1: DPI input port + - port@2: eDP/DP output port + +[1]: Documentation/devicetree/bindings/graph.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + edp-bridge@68 { + compatible = "toshiba,tc358767"; + reg = <0x68>; + shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + clock-names = "ref"; + clocks = <&edp_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@2 { + reg = <2>; + + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt index d685be898d0c..e9c65746e2f1 100644 --- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -1,7 +1,7 @@ * Currus Logic CLPS711X Framebuffer Required properties: -- compatible: Shall contain "cirrus,clps711x-fb". +- compatible: Shall contain "cirrus,ep7209-fb". - reg : Physical base address and length of the controller's registers + location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. @@ -18,7 +18,7 @@ Optional properties: Example: fb: fb@800002c0 { - compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks 2>; lcd-supply = <®5v0>; diff --git a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt index acd5668b1ce1..508aee461e0d 100644 --- a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt +++ b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt @@ -8,6 +8,7 @@ Required properties: Optional properties: - label: a symbolic name for the connector - hpd-gpios: HPD GPIO number +- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing Required nodes: - Video port for HDMI input diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index 377afbf5122a..c9fd7b3807e7 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -5,7 +5,8 @@ Exynos series of SoCs which transfers the image data from a video memory buffer to an external LCD interface. Required properties: -- compatible: value should be "samsung,exynos5433-decon"; +- compatible: value should be one of: + "samsung,exynos5433-decon", "samsung,exynos5433-decon-tv"; - reg: physical base address and length of the DECON registers set. - interrupts: should contain a list of all DECON IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier format @@ -16,7 +17,7 @@ Required properties: - clocks: must include clock specifiers corresponding to entries in the clock-names property. - clock-names: list of clock names sorted in the same order as the clocks - property. Must contain "aclk_decon", "aclk_smmu_decon0x", + property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index fe4a7a2dea9c..ade5d8eebf85 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -1,20 +1,3 @@ -Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP) - -DisplayPort is industry standard to accommodate the growing board adoption -of digital display technology within the PC and CE industries. -It consolidates the internal and external connection methods to reduce device -complexity and cost. It also supports necessary features for important cross -industry applications and provides performance scalability to enable the next -generation of displays that feature higher color depths, refresh rates, and -display resolutions. - -eDP (embedded display port) device is compliant with Embedded DisplayPort -standard as follows, -- DisplayPort standard 1.1a for Exynos5250 and Exynos5260. -- DisplayPort standard 1.3 for Exynos5422s and Exynos5800. - -eDP resides between FIMD and panel or FIMD and bridge such as LVDS. - The Exynos display port interface should be configured based on the type of panel connected to it. @@ -48,26 +31,6 @@ Required properties for dp-controller: from general PHY binding: the phandle for the PHY device. -phy-names: from general PHY binding: Should be "dp". - -samsung,color-space: - input video data format. - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 - -samsung,dynamic-range: - dynamic range for input video data. - VESA = 0, CEA = 1 - -samsung,ycbcr-coeff: - YCbCr co-efficients for input video. - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 - -samsung,color-depth: - number of bits per colour component. - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 - -samsung,link-rate: - link rate supported by the panel. - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A - -samsung,lane-count: - number of lanes supported by the panel. - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 - - display-timings: timings for the connected panel as described by - Documentation/devicetree/bindings/display/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -83,17 +46,31 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection -Video interfaces: - Device node can contain video interface port nodes according to [1]. - The following are properties specific to those nodes: - - endpoint node connected to bridge or panel node: - - remote-endpoint: specifies the endpoint in panel or bridge node. - This node is required in all kinds of exynos dp - to represent the connection between dp and bridge - or dp and panel. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + -video interfaces: Device node can contain video interface port + nodes according to [1]. + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/panel/display-timing.txt + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt + -phys (required) + -phy-names (required) + -hpd-gpios (optional) + force-hpd (optional) + +Deprecated properties for DisplayPort: +-interlaced: deprecated prop that can parsed from drm_display_mode. +-vsync-active-high: deprecated prop that can parsed from drm_display_mode. +-hsync-active-high: deprecated prop that can parsed from drm_display_mode. +-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode. +-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode. +-samsung,color-space: deprecated prop that can parsed from drm_display_info. +-samsung,color-depth: deprecated prop that can parsed from drm_display_info. +-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method. +-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method. +-samsung,hpd-gpio: deprecated name for hpd-gpios. + +------------------------------------------------------------------------------- Example: @@ -112,13 +89,6 @@ SOC specific portion: Board Specific portion: dp-controller { - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <4>; - display-timings { native-mode = <&lcd_timing>; lcd_timing: 1366x768 { @@ -135,18 +105,9 @@ Board Specific portion: }; ports { - port { + port@0 { dp_out: endpoint { - remote-endpoint = <&dp_in>; - }; - }; - }; - - panel { - ... - port { - dp_in: endpoint { - remote-endpoint = <&dp_out>; + remote-endpoint = <&bridge_in>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 22756b3dede2..a78265993665 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -41,7 +41,7 @@ Video interfaces: endpoint node connected from mic node (reg = 0): - remote-endpoint: specifies the endpoint in mic node. This node is required for Exynos5433 mipi dsi. So mic can access to panel node - thoughout this dsi node. + throughout this dsi node. endpoint node connected to panel node (reg = 1): - remote-endpoint: specifies the endpoint in panel node. This node is required in all kinds of exynos mipi dsi to represent diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index d474f59be6d6..a2ec4c1c9382 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -5,6 +5,7 @@ Required properties: 1) "samsung,exynos4210-hdmi" 2) "samsung,exynos4212-hdmi" 3) "samsung,exynos5420-hdmi" + 4) "samsung,exynos5433-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -12,6 +13,11 @@ Required properties: a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 4210, 4212, 5420 and 5433: - clocks: list of clock IDs from SoC clock driver. a) hdmi: Gate of HDMI IP bus clock. b) sclk_hdmi: Gate of HDMI special clock. @@ -25,9 +31,24 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". -- ddc: phandle to the hdmi ddc node -- phy: phandle to the hdmi phy node -- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 5433: +- clocks: list of clock specifiers according to common clock bindings. + a) hdmi_pclk: Gate of HDMI IP APB bus. + b) hdmi_i_pclk: Gate of HDMI-PHY IP APB bus. + d) i_tmds_clk: Gate of HDMI TMDS clock. + e) i_pixel_clk: Gate of HDMI pixel clock. + f) i_spdif_clk: Gate of HDMI SPDIF clock. + g) oscclk: Oscillator clock, used as parent of following *_user clocks + in case HDMI-PHY is not operational. + h) tmds_clko: TMDS clock generated by HDMI-PHY. + i) tmds_clko_user: MUX used to switch between oscclk and tmds_clko, + respectively if HDMI-PHY is off and operational. + j) pixel_clko: Pixel clock generated by HDMI-PHY. + k) pixel_clko_user: MUX used to switch between oscclk and pixel_clko, + respectively if HDMI-PHY is off and operational. +- clock-names: aliases for above clock specfiers. +- samsung,sysreg: handle to syscon used to control the system registers. Example: diff --git a/Documentation/devicetree/bindings/display/fsl,dcu.txt b/Documentation/devicetree/bindings/display/fsl,dcu.txt index ebf1be9ae393..63ec2a624aa9 100644 --- a/Documentation/devicetree/bindings/display/fsl,dcu.txt +++ b/Documentation/devicetree/bindings/display/fsl,dcu.txt @@ -6,17 +6,29 @@ Required properties: * "fsl,vf610-dcu". - reg: Address and length of the register set for dcu. -- clocks: From common clock binding: handle to dcu clock. -- clock-names: From common clock binding: Shall be "dcu". +- clocks: Handle to "dcu" and "pix" clock (in the order below) + This can be the same clock (e.g. LS1021a) + See ../clocks/clock-bindings.txt for details. +- clock-names: Should be "dcu" and "pix" + See ../clocks/clock-bindings.txt for details. - big-endian Boolean property, LS1021A DCU registers are big-endian. -- fsl,panel: The phandle to panel node. +- port Video port for the panel output + +Optional properties: +- fsl,tcon: The phandle to the timing controller node. Examples: dcu: dcu@2ce0000 { compatible = "fsl,ls1021a-dcu"; reg = <0x0 0x2ce0000 0x0 0x10000>; - clocks = <&platform_clk 0>; - clock-names = "dcu"; + clocks = <&platform_clk 0>, <&platform_clk 0>; + clock-names = "dcu", "pix"; big-endian; - fsl,panel = <&panel>; + fsl,tcon = <&tcon>; + + port { + dcu_out: endpoint { + remote-endpoint = <&panel_out>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/display/fsl,tcon.txt b/Documentation/devicetree/bindings/display/fsl,tcon.txt new file mode 100644 index 000000000000..6fa4ab668db5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/fsl,tcon.txt @@ -0,0 +1,18 @@ +Device Tree bindings for Freescale TCON Driver + +Required properties: +- compatible: Should be one of + * "fsl,vf610-tcon". + +- reg: Address and length of the register set for tcon. +- clocks: From common clock binding: handle to tcon ipg clock. +- clock-names: From common clock binding: Shall be "ipg". + +Examples: +timing-controller@4003d000 { + compatible = "fsl,vf610-tcon"; + reg = <0x4003d000 0x1000>; + clocks = <&clks VF610_CLK_TCON0>; + clock-names = "ipg"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt new file mode 100644 index 000000000000..d270bfe4e4e0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt @@ -0,0 +1,72 @@ +Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver + +A DSI Host Controller resides in the middle of display controller and external +HDMI converter or panel. + +Required properties: +- compatible: value should be "hisilicon,hi6220-dsi". +- reg: physical base address and length of dsi controller's registers. +- clocks: contains APB clock phandle + clock-specifier pair. +- clock-names: should be "pclk". +- ports: contains DSI controller input and output sub port. + The input port connects to ADE output port with the reg value "0". + The output port with the reg value "1", it could connect to panel or + any other bridge endpoints. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +A example of HiKey board hi6220 SoC and board specific DT entry: +Example: + +SoC specific: + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; + + +Board specific: + &dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; + }; + + &i2c2 { + ... + + adv7533: adv7533@39 { + ... + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt new file mode 100644 index 000000000000..38dc9d60eef8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -0,0 +1,64 @@ +Device-Tree bindings for hisilicon ADE display controller driver + +ADE (Advanced Display Engine) is the display controller which grab image +data from memory, do composition, do post image processing, generate RGB +timing stream and transfer to DSI. + +Required properties: +- compatible: value should be "hisilicon,hi6220-ade". +- reg: physical base address and length of the ADE controller's registers. +- hisilicon,noc-syscon: ADE NOC QoS syscon. +- resets: The ADE reset controller node. +- interrupt: the ldi vblank interrupt number used. +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain: + "clk_ade_core" for the ADE core clock. + "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with + jpeg codec. + "clk_ade_pix" for the ADE pixel clok. +- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' + phandle + clock-specifier pairs. +- assigned-clock-rates: clock rates, one for each entry in assigned-clocks. + The rate of "clk_ade_core" could be "360000000" or "180000000"; + The rate of "clk_codec_jpeg" could be or less than "1440000000". + These rate values could be configured according to performance and power + consumption. +- port: the output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected DSI input endpoint. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +Optional properties: +- dma-coherent: Present if dma operations are coherent. + + +A example of HiKey board hi6220 SoC specific DT entry: +Example: + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 0a175d991b52..a407462c885e 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,6 +62,7 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt new file mode 100644 index 000000000000..db6e77edbea8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -0,0 +1,203 @@ +Mediatek display subsystem +========================== + +The Mediatek display subsystem consists of various DISP function blocks in the +MMSYS register space. The connections between them can be configured by output +and input selectors in the MMSYS_CONFIG register space. Pixel clock and start +of frame signal are distributed to the other function blocks by a DISP_MUTEX +function block. + +All DISP device tree nodes must be siblings to the central MMSYS_CONFIG node. +For a description of the MMSYS_CONFIG binding, see +Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt. + +DISP function blocks +==================== + +A display stream starts at a source function block that reads pixel data from +memory and ends with a sink function block that drives pixels on a display +interface, or writes pixels back to memory. All DISP function blocks have +their own register space, interrupt, and clock gate. The blocks that can +access memory additionally have to list the IOMMU and local arbiter they are +connected to. + +For a description of the display interface sink function blocks, see +Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt and +Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt. + +Required properties (all function blocks): +- compatible: "mediatek,<chip>-disp-<function>", one of + "mediatek,<chip>-disp-ovl" - overlay (4 layers, blending, csc) + "mediatek,<chip>-disp-rdma" - read DMA / line buffer + "mediatek,<chip>-disp-wdma" - write DMA + "mediatek,<chip>-disp-color" - color processor + "mediatek,<chip>-disp-aal" - adaptive ambient light controller + "mediatek,<chip>-disp-gamma" - gamma correction + "mediatek,<chip>-disp-merge" - merge streams from two RDMA sources + "mediatek,<chip>-disp-split" - split stream to two encoders + "mediatek,<chip>-disp-ufoe" - data compression engine + "mediatek,<chip>-dsi" - DSI controller, see mediatek,dsi.txt + "mediatek,<chip>-dpi" - DPI controller, see mediatek,dpi.txt + "mediatek,<chip>-disp-mutex" - display mutex + "mediatek,<chip>-disp-od" - overdrive +- reg: Physical base address and length of the function block register space +- interrupts: The interrupt signal from the function block (required, except for + merge and split function blocks). +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. + For most function blocks this is just a single clock input. Only the DSI and + DPI controller nodes have multiple clock inputs. These are documented in + mediatek,dsi.txt and mediatek,dpi.txt, respectively. + +Required properties (DMA function blocks): +- compatible: Should be one of + "mediatek,<chip>-disp-ovl" + "mediatek,<chip>-disp-rdma" + "mediatek,<chip>-disp-wdma" +- larb: Should contain a phandle pointing to the local arbiter device as defined + in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt +- iommus: Should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Examples: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + #clock-cells = <1>; +}; + +ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; +}; + +ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; +}; + +rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; +}; + +rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; +}; + +rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; +}; + +wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; +}; + +wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; +}; + +color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; +}; + +color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; +}; + +aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; +}; + +gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; +}; + +ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; +}; + +dsi0: dsi@1401b000 { + /* See mediatek,dsi.txt for details */ +}; + +dpi0: dpi@1401d000 { + /* See mediatek,dpi.txt for details */ +}; + +mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; +}; + +od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OD>; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt new file mode 100644 index 000000000000..b6a7e7397b8b --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -0,0 +1,35 @@ +Mediatek DPI Device +=================== + +The Mediatek DPI function block is a sink of the display subsystem and +provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel +output bus. + +Required properties: +- compatible: "mediatek,<chip>-dpi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "engine", and "pll" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached HDMI or LVDS encoder chip. + +Example: + +dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000000..2b1585a34b85 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,60 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,<chip>-dsi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,<chip>-mipi-tx" +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt new file mode 100644 index 000000000000..7b124242b0c5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt @@ -0,0 +1,148 @@ +Mediatek HDMI Encoder +===================== + +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from +its parallel input. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi". +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "pll", "bclk", and "spdif". +- phys: phandle link to the HDMI PHY node. + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details. +- phy-names: must contain "hdmi" +- mediatek,syscon-hdmi: phandle link and register offset to the system + configuration registers. For mt8173 this must be offset 0x900 into the + MMSYS_CONFIG region: <&mmsys 0x900>. +- ports: A node containing input and output port nodes with endpoint + definitions as documented in Documentation/devicetree/bindings/graph.txt. +- port@0: The input port in the ports node should be connected to a DPI output + port. +- port@1: The output port in the ports node should be connected to the input + port of a connector node that contains a ddc-i2c-bus property, or to the + input port of an attached bridge chip, such as a SlimPort transmitter. + +HDMI CEC +======== + +The HDMI CEC controller handles hotplug detection and CEC communication. + +Required properties: +- compatible: Should be "mediatek,<chip>-cec" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clock + +HDMI DDC +======== + +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins. +The Mediatek's I2C controller is used to interface with I2C devices. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi-ddc" +- reg: Physical base address and length of the controller's registers +- clocks: device clock +- clock-names: Should be "ddc-i2c". + +HDMI PHY +======== + +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel +output and drives the HDMI pads. + +Required properties: +- compatible: "mediatek,<chip>-hdmi-phy" +- reg: Physical base address and length of the module's registers +- clocks: PLL reference clock +- clock-names: must contain "pll_ref" +- clock-output-names: must be "hdmitx_dig_cts" on mt8173 +- #phy-cells: must be <0> +- #clock-cells: must be <0> + +Optional properties: +- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa +- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c + +Example: + +cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; +}; + +hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +hdmi_ddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + reg = <0 0x11012000 0 0x1c>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; +}; + +hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + +connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-i2c-bus = <&hdmiddc0>; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index f5948c48b9a2..6b1cab17f52d 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -11,8 +11,7 @@ Required properties: be 0 or 1, since we have 2 DSI controllers at most for now. - interrupts: The interrupt signal from the DSI block. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. - clock-names: the following clocks are required: * "mdp_core_clk" * "iface_clk" @@ -23,16 +22,21 @@ Required properties: * "core_clk" For DSIv2, we need an additional clock: * "src_clk" +- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. +- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided + by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node - vddio-supply: phandle to vdd-io regulator device node - vdda-supply: phandle to vdda regulator device node -- qcom,dsi-phy: phandle to DSI PHY device node +- phys: phandle to DSI PHY device node +- phy-names: the name of the corresponding PHY device - syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) +- ports: Contains 2 DSI controller ports as child nodes. Each port contains + an endpoint subnode as defined in [2] and [3]. Optional properties: - panel@0: Node of panel connected to this DSI controller. - See files in Documentation/devicetree/bindings/display/panel/ for each supported - panel. + See files in [4] for each supported panel. - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. - qcom,master-dsi: Boolean value indicating if the DSI controller is driving @@ -44,34 +48,38 @@ Optional properties: - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-n: the "sleep" pinctrl state -- port: DSI controller output port, containing one endpoint subnode. +- ports: contains DSI controller input and output ports as children, each + containing one endpoint subnode. DSI Endpoint properties: - - remote-endpoint: set to phandle of the connected panel's endpoint. - See Documentation/devicetree/bindings/graph.txt for device graph info. - - qcom,data-lane-map: this describes how the logical DSI lanes are mapped - to the physical lanes on the given platform. The value contained in - index n describes what logical data lane is mapped to the physical data - lane n (DATAn, where n lies between 0 and 3). + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's + input endpoint. For port@1, set to the MDP interface output. See [2] for + device graph info. + + - data-lanes: this describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. See + [3] for more info on the data-lanes property. For example: - qcom,data-lane-map = <3 0 1 2>; + data-lanes = <3 0 1 2>; - The above mapping describes that the logical data lane DATA3 is mapped to - the physical data lane DATA0, logical DATA0 to physical DATA1, logic DATA1 - to phys DATA2 and logic DATA2 to phys DATA3. + The above mapping describes that the logical data lane DATA0 is mapped to + the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 + to phys DATA1 and logic DATA3 to phys DATA2. There are only a limited number of physical to logical mappings possible: - - "0123": Logic 0->Phys 0; Logic 1->Phys 1; Logic 2->Phys 2; Logic 3->Phys 3; - "3012": Logic 3->Phys 0; Logic 0->Phys 1; Logic 1->Phys 2; Logic 2->Phys 3; - "2301": Logic 2->Phys 0; Logic 3->Phys 1; Logic 0->Phys 2; Logic 1->Phys 3; - "1230": Logic 1->Phys 0; Logic 2->Phys 1; Logic 3->Phys 2; Logic 0->Phys 3; - "0321": Logic 0->Phys 0; Logic 3->Phys 1; Logic 2->Phys 2; Logic 1->Phys 3; - "1032": Logic 1->Phys 0; Logic 0->Phys 1; Logic 3->Phys 2; Logic 2->Phys 3; - "2103": Logic 2->Phys 0; Logic 1->Phys 1; Logic 0->Phys 2; Logic 3->Phys 3; - "3210": Logic 3->Phys 0; Logic 2->Phys 1; Logic 1->Phys 2; Logic 0->Phys 3; + <0 1 2 3> + <1 2 3 0> + <2 3 0 1> + <3 0 1 2> + <0 3 2 1> + <1 0 3 2> + <2 1 0 3> + <3 2 1 0> DSI PHY: Required properties: @@ -86,11 +94,12 @@ Required properties: * "dsi_pll" * "dsi_phy" * "dsi_phy_regulator" +- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating + 2 clocks: A byte clock (index 0), and a pixel clock (index 1). - qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should be 0 or 1, since we have 2 DSI PHYs at most for now. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node @@ -99,11 +108,16 @@ Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY regulator is wanted. +[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt +[2] Documentation/devicetree/bindings/graph.txt +[3] Documentation/devicetree/bindings/media/video-interfaces.txt +[4] Documentation/devicetree/bindings/display/panel/ + Example: - mdss_dsi0: qcom,mdss_dsi@fd922800 { + dsi0: dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; qcom,dsi-host-index = <0>; - interrupt-parent = <&mdss_mdp>; + interrupt-parent = <&mdp>; interrupts = <4 0>; reg-names = "dsi_ctrl"; reg = <0xfd922800 0x200>; @@ -124,19 +138,48 @@ Example: <&mmcc MDSS_AHB_CLK>, <&mmcc MDSS_MDP_CLK>, <&mmcc MDSS_PCLK0_CLK>; + + assigned-clocks = + <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = + <&dsi_phy0 0>, + <&dsi_phy0 1>; + vdda-supply = <&pma8084_l2>; vdd-supply = <&pma8084_l22>; vddio-supply = <&pma8084_l12>; - qcom,dsi-phy = <&mdss_dsi_phy0>; + phys = <&dsi_phy0>; + phy-names ="dsi-phy"; qcom,dual-dsi-mode; qcom,master-dsi; qcom,sync-dual-dsi; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mdss_dsi_active>; - pinctrl-1 = <&mdss_dsi_suspend>; + pinctrl-0 = <&dsi_active>; + pinctrl-1 = <&dsi_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -152,16 +195,9 @@ Example: }; }; }; - - port { - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - lanes = <0 1 2 3>; - }; - }; }; - mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { + dsi_phy0: dsi-phy@fd922a00 { compatible = "qcom,dsi-phy-28nm-hpm"; qcom,dsi-phy-index = <0>; reg-names = @@ -173,6 +209,7 @@ Example: <0xfd922d80 0x7b>; clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; + #clock-cells = <1>; vddio-supply = <&pma8084_l12>; qcom,dsi-phy-regulator-ldo-mode; diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt deleted file mode 100644 index a214f6cd0363..000000000000 --- a/Documentation/devicetree/bindings/display/msm/mdp.txt +++ /dev/null @@ -1,59 +0,0 @@ -Qualcomm adreno/snapdragon display controller - -Required properties: -- compatible: - * "qcom,mdp4" - mdp4 - * "qcom,mdp5" - mdp5 -- reg: Physical base address and length of the controller's registers. -- interrupts: The interrupt signal from the display controller. -- connectors: array of phandles for output device(s) -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required. - For MDP4: - * "core_clk" - * "iface_clk" - * "lut_clk" - * "src_clk" - * "hdmi_clk" - * "mdp_clk" - For MDP5: - * "bus_clk" - * "iface_clk" - * "core_clk_src" - * "core_clk" - * "lut_clk" (some MDP5 versions may not need this) - * "vsync_clk" - -Optional properties: -- gpus: phandle for gpu device -- clock-names: the following clocks are optional: - * "lut_clk" - -Example: - -/ { - ... - - mdp: qcom,mdp@5100000 { - compatible = "qcom,mdp4"; - reg = <0x05100000 0xf0000>; - interrupts = <GIC_SPI 75 0>; - connectors = <&hdmi>; - gpus = <&gpu>; - clock-names = - "core_clk", - "iface_clk", - "lut_clk", - "src_clk", - "hdmi_clk", - "mdp_clk"; - clocks = - <&mmcc MDP_SRC>, - <&mmcc MDP_AHB_CLK>, - <&mmcc MDP_LUT_CLK>, - <&mmcc TV_SRC>, - <&mmcc HDMI_TV_CLK>, - <&mmcc MDP_TV_CLK>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp4.txt b/Documentation/devicetree/bindings/display/msm/mdp4.txt new file mode 100644 index 000000000000..3c341a15ccdc --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp4.txt @@ -0,0 +1,112 @@ +Qualcomm adreno/snapdragon MDP4 display controller + +Description: + +This is the bindings documentation for the MDP4 display controller found in +SoCs like MSM8960, APQ8064 and MSM8660. + +Required properties: +- compatible: + * "qcom,mdp4" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "core_clk" + * "iface_clk" + * "bus_clk" + * "lut_clk" + * "hdmi_clk" + * "tv_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The output port mappings are: + Port 0 -> LCDC/LVDS + Port 1 -> DSI1 Cmd/Video + Port 2 -> DSI2 Cmd/Video + Port 3 -> DTV + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + ... + ports { + ... + port@0 { + reg = <0>; + hdmi_in: endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + ... + }; + ... + }; + + ... + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + clocks = + <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt new file mode 100644 index 000000000000..30c11ea83754 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -0,0 +1,160 @@ +Qualcomm adreno/snapdragon MDP5 display controller + +Description: + +This is the bindings documentation for the Mobile Display Subsytem(MDSS) that +encapsulates sub-blocks like MDP5, DSI, HDMI, eDP etc, and the MDP5 display +controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996. + +MDSS: +Required properties: +- compatible: + * "qcom,mdss" - MDSS +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdss_phys" + * "vbif_phys" +- interrupts: The interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "iface_clk" + * "bus_clk" + * "vsync_clk" +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +MDP5: +Required properties: +- compatible: + * "qcom,mdp5" - MDP5 +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdp_phys" +- interrupts: Interrupt line from MDP5 to MDSS interrupt controller. +- interrupt-parent: phandle to the MDSS block + through MDP block +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. +- * "bus_clk" +- * "iface_clk" +- * "core_clk" +- * "vsync_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The availability of output ports can vary across SoC revisions: + + For MSM8974 and APQ8084: + Port 0 -> MDP_INTF0 (eDP) + Port 1 -> MDP_INTF1 (DSI1) + Port 2 -> MDP_INTF2 (DSI2) + Port 3 -> MDP_INTF3 (HDMI) + + For MSM8916: + Port 0 -> MDP_INTF1 (DSI1) + + For MSM8994 and MSM8996: + Port 0 -> MDP_INTF1 (DSI1) + Port 1 -> MDP_INTF2 (DSI2) + Port 2 -> MDP_INTF3 (HDMI) + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "vsync_clk" + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "core_clk", + "vsync_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + ... + ports { + ... + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + ... + }; + ... + }; + + dsi_phy0: dsi-phy@1a98300 { + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt new file mode 100644 index 000000000000..3e10cd782491 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt @@ -0,0 +1,7 @@ +Innolux AT070TN92 7.0" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at070tn92" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt new file mode 100644 index 000000000000..b9877acad012 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt @@ -0,0 +1,7 @@ +LG LP079QX1-SP0V 7.9" (1536x2048 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp079qx1-sp0v" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt new file mode 100644 index 000000000000..42141516f078 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt @@ -0,0 +1,7 @@ +LG 9.7" (2048x1536 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp097qx1-spa1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt new file mode 100644 index 000000000000..74540a090669 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt @@ -0,0 +1,7 @@ +Olimex 4.3" TFT LCD panel + +Required properties: +- compatible: should be "olimex,lcd-olinuxino-43-ts" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt new file mode 100644 index 000000000000..3d8a5e029242 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt @@ -0,0 +1,7 @@ +On Tat Industrial Company 7" DPI TFT panel. + +Required properties: +- compatible: should be "ontat,yx700wv03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt index 216c894d4f99..b52ac52757df 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt @@ -7,6 +7,8 @@ Required properties: Optional properties: - label: a symbolic name for the panel - enable-gpios: panel enable gpio +- reset-gpios: GPIO to control the RESET pin +- vcc-supply: phandle of regulator that will be used to enable power to the display Required nodes: - "panel-timing" containing video timings diff --git a/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt new file mode 100644 index 000000000000..dba298b43b24 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt @@ -0,0 +1,7 @@ +Samsung 12.2" (2560x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "samsung,lsn122dl01-c01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt new file mode 100644 index 000000000000..4aff25b8dfe6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt @@ -0,0 +1,7 @@ +Sharp Display Corp. LQ101K1LY04 10.07" WXGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq101k1ly04" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt new file mode 100644 index 000000000000..bcb0e8a29f71 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt @@ -0,0 +1,7 @@ +Sharp 12.3" (2400x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq123p1jx31" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt new file mode 100644 index 000000000000..1e87fe6078af --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt @@ -0,0 +1,7 @@ +Starry 12.2" (1920x1200 pixels) TFT LCD panel + +Required properties: +- compatible: should be "starry,kr122ea0sra" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt new file mode 100644 index 000000000000..a2613b9675df --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 7" integrated projected capacitive touch display with, +800 x 480 (WVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f07a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt new file mode 100644 index 000000000000..b9d051196ba9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 10.1" integrated projected capacitive touch display with, +1024 x 600 (WSVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f10a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt new file mode 100644 index 000000000000..01cced1c2a18 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -0,0 +1,99 @@ +Rockchip RK3288 specific extensions to the Analogix Display Port +================================ + +Required properties: +- compatible: "rockchip,rk3288-dp", + "rockchip,rk3399-edp"; + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. + +- clock-names: from common clock binding: + Required elements: "dp" "pclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. +- pinctrl-0: pin-control mode. should be <&edp_hpd> + +- reset-names: Must include the name "dp" + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: there are 2 port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0: contained 2 endpoints, connecting to the output of vop. + Port 1: contained 1 endpoint, connecting to the input of panel. + +Optional property for different chips: +- clocks: from common clock binding: handle to grf_vio clock. + +- clock-names: from common clock binding: + Required elements: "grf" + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt +- phys (required) +- phy-names (required) +- hpd-gpios (optional) +- force-hpd (optional) +------------------------------------------------------------------------------- + +Example: + dp-controller: dp@ff970000 { + compatible = "rockchip,rk3288-dp"; + reg = <0xff970000 0x4000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; + clock-names = "dp", "pclk"; + phys = <&dp_phy>; + phy-names = "dp"; + + rockchip,grf = <&grf>; + resets = <&cru 111>; + reset-names = "dp"; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + edp_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + edp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_edp>; + }; + edp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_edp>; + }; + }; + + edp_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + edp_out_panel: endpoint { + reg = <0>; + remote-endpoint = <&panel_in_edp> + }; + }; + }; + }; + + pinctrl { + edp { + edp_hpd: edp-hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/snps,arcpgu.txt b/Documentation/devicetree/bindings/display/snps,arcpgu.txt new file mode 100644 index 000000000000..c5c7dfd37df2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/snps,arcpgu.txt @@ -0,0 +1,35 @@ +ARC PGU + +This is a display controller found on several development boards produced +by Synopsys. The ARC PGU is an RGB streamer that reads the data from a +framebuffer and sends it to a single digital encoder (usually HDMI). + +Required properties: + - compatible: "snps,arcpgu" + - reg: Physical base address and length of the controller's registers. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For ARC PGU it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The PGU connection to an encoder chip. + +Example: + +/ { + ... + + pgu@XXXXXXXX { + compatible = "snps,arcpgu"; + reg = <0xXXXXXXXX 0x400>; + clocks = <&clock_node>; + clock-names = "pxlclk"; + + port { + pgu_output: endpoint { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt new file mode 100644 index 000000000000..df8f4aeefe4c --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -0,0 +1,258 @@ +Allwinner A10 Display Pipeline +============================== + +The Allwinner A10 Display pipeline is composed of several components +that are going to be documented below: + +TV Encoder +---------- + +The TV Encoder supports the composite and VGA output. It is one end of +the pipeline. + +Required properties: + - compatible: value should be "allwinner,sun4i-a10-tv-encoder". + - reg: base address and size of memory-mapped region + - clocks: the clocks driving the TV encoder + - resets: phandle to the reset controller driving the encoder + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. + +TCON +---- + +The TCON acts as a timing controller for RGB, LVDS and TV interfaces. + +Required properties: + - compatible: value should be "allwinner,sun5i-a13-tcon". + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the TCON. Three are needed: + - 'ahb': the interface clocks + - 'tcon-ch0': The clock driving the TCON channel 0 + - 'tcon-ch1': The clock driving the TCON channel 1 + - resets: phandles to the reset controllers driving the encoder + - "lcd": the reset line for the TCON channel 0 + + - clock-names: the clock names mentioned above + - reset-names: the reset names mentioned above + - clock-output-names: Name of the pixel clock created + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, the second one the output + + The output should have two endpoints. The first is the block + connected to the TCON channel 0 (usually a panel or a bridge), the + second the block connected to the TCON channel 1 (usually the TV + encoder) + + +Display Engine Backend +---------------------- + +The display engine backend exposes layers and sprites to the +system. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-backend + - reg: base address and size of the memory-mapped region. + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the output + +Display Engine Frontend +----------------------- + +The display engine frontend does formats conversion, scaling, +deinterlacing and color space conversion. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-frontend + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs + + +Display Engine Pipeline +----------------------- + +The display engine pipeline (and its entry point, since it can be +either directly the backend or the frontend) is represented as an +extra node. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-engine + + - allwinner,pipelines: list of phandle to the display engine + frontends available. + +Example: + +panel: panel { + compatible = "olimex,lcd-olinuxino-43-ts"; + #address-cells = <1>; + #size-cells = <0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; +}; + +tve0: tv-encoder@01c0a000 { + compatible = "allwinner,sun4i-a10-tv-encoder"; + reg = <0x01c0a000 0x1000>; + clocks = <&ahb_gates 34>; + resets = <&tcon_ch0_clk 0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + tve0_in_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_tve0>; + }; + }; +}; + +tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun5i-a13-tcon"; + reg = <0x01c0c000 0x1000>; + interrupts = <44>; + resets = <&tcon_ch0_clk 1>; + reset-names = "lcd"; + clocks = <&ahb_gates 36>, + <&tcon_ch0_clk>, + <&tcon_ch1_clk>; + clock-names = "ahb", + "tcon-ch0", + "tcon-ch1"; + clock-output-names = "tcon-pixel-clock"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon0_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + + tcon0_out_tve0: endpoint@1 { + reg = <1>; + remote-endpoint = <&tve0_in_tcon0>; + }; + }; + }; +}; + +fe0: display-frontend@1e00000 { + compatible = "allwinner,sun5i-a13-display-frontend"; + reg = <0x01e00000 0x20000>; + interrupts = <47>; + clocks = <&ahb_gates 46>, <&de_fe_clk>, + <&dram_gates 25>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_fe_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe0_out_be0: endpoint { + remote-endpoint = <&be0_in_fe0>; + }; + }; + }; +}; + +be0: display-backend@1e60000 { + compatible = "allwinner,sun5i-a13-display-backend"; + reg = <0x01e60000 0x10000>; + clocks = <&ahb_gates 44>, <&de_be_clk>, + <&dram_gates 26>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_be_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be0_in_fe0: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe0_out_be0>; + }; + }; + + be0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_be0>; + }; + }; + }; +}; + +display-engine { + compatible = "allwinner,sun5i-a13-display-engine"; + allwinner,pipelines = <&fe0>; +}; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index a3bd8c050c4e..0fad7ed2ea19 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -208,6 +208,7 @@ of the following host1x client modules: See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - sor: clock input for the SOR hardware + - source: source clock for the SOR clock - parent: input for the pixel clock - dp: reference clock for the SOR clock - safe: safe reference for the SOR clock during power up @@ -226,9 +227,9 @@ of the following host1x client modules: - nvidia,dpaux: phandle to a DispayPort AUX interface - dpaux: DisplayPort AUX interface - - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise, - must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where - <chip> is tegra132. + - compatible : Should contain one of the following: + - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132 + - "nvidia,tegra210-dpaux": for Tegra210 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. @@ -241,6 +242,12 @@ of the following host1x client modules: - reset-names: Must include the following entries: - dpaux - vdd-supply: phandle of a supply that powers the DisplayPort link + - i2c-bus: Subnode where I2C slave devices are listed. This subnode + must be always present. If there are no I2C slave devices, an empty + node should be added. See ../../i2c/i2c.txt for more information. + + See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information + regarding the DPAUX pad controller bindings. Example: diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt index 1396078d15ac..baf9b34d20bf 100644 --- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt +++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt @@ -12,6 +12,10 @@ Required properties: - reg: Should contain DMA registers location and length. - interrupts: Should contain the DMA interrupts associated to the DMA channels in ascending order. +- interrupt-names: Should contain the names of the interrupt + in the form "dmaXX". + Use "dma-shared-all" for the common interrupt line + that is shared by all dma channels. - #dma-cells: Must be <1>, the cell in the dmas property of the client device represents the DREQ number. - brcm,dma-channel-mask: Bit mask representing the channels @@ -34,13 +38,35 @@ dma: dma@7e007000 { <1 24>, <1 25>, <1 26>, + /* dma channel 11-14 share one irq */ <1 27>, + <1 27>, + <1 27>, + <1 27>, + /* unused shared irq for all channels */ <1 28>; + interrupt-names = "dma0", + "dma1", + "dma2", + "dma3", + "dma4", + "dma5", + "dma6", + "dma7", + "dma8", + "dma9", + "dma10", + "dma11", + "dma12", + "dma13", + "dma14", + "dma-shared-all"; #dma-cells = <1>; brcm,dma-channel-mask = <0x7f35>; }; + DMA clients connected to the BCM2835 DMA controller must use the format described in the dma.txt file, using a two-cell specifier for each channel. diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index dc8d3aac1aa9..3c9a57a8443b 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -8,6 +8,7 @@ Required properties: "fsl,imx51-sdma" "fsl,imx53-sdma" "fsl,imx6q-sdma" + "fsl,imx7d-sdma" The -to variants should be preferred since they allow to determine the correct ROM script addresses needed for the driver to work without additional firmware. @@ -58,6 +59,15 @@ The third cell specifies the transfer priority as below. 1 Medium 2 Low +Optional properties: + +- gpr : The phandle to the General Purpose Register (GPR) node. +- fsl,sdma-event-remap : Register bits of sdma event remap, the format is + <reg shift val>. + reg is the GPR register offset. + shift is the bit position inside the GPR register. + val is the value of the bit (0 or 1). + Examples: sdma@83fb0000 { @@ -83,3 +93,21 @@ ssi2: ssi@70014000 { dma-names = "rx", "tx"; fsl,fifo-depth = <15>; }; + +Using the fsl,sdma-event-remap property: + +If we want to use SDMA on the SAI1 port on a MX6SX: + +&sdma { + gpr = <&gpr>; + /* SDMA events remap for SAI1_RX and SAI1_TX */ + fsl,sdma-event-remap = <0 15 1>, <0 16 1>; +}; + +The fsl,sdma-event-remap property in this case has two values: +- <0 15 1> means that the offset is 0, so GPR0 is the register of the +SDMA remap. Bit 15 of GPR0 selects between UART4_RX and SAI1_RX. +Setting bit 15 to 1 selects SAI1_RX. +- <0 16 1> means that the offset is 0, so GPR0 is the register of the +SDMA remap. Bit 16 of GPR0 selects between UART4_TX and SAI1_TX. +Setting bit 16 to 1 selects SAI1_TX. diff --git a/Documentation/devicetree/bindings/dma/mv-xor-v2.txt b/Documentation/devicetree/bindings/dma/mv-xor-v2.txt new file mode 100644 index 000000000000..217a90eaabe7 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mv-xor-v2.txt @@ -0,0 +1,24 @@ +* Marvell XOR v2 engines + +Required properties: +- compatible: one of the following values: + "marvell,armada-7k-xor" + "marvell,xor-v2" +- reg: Should contain registers location and length (two sets) + the first set is the DMA registers + the second set is the global registers +- msi-parent: Phandle to the MSI-capable interrupt controller used for + interrupts. + +Optional properties: +- clocks: Optional reference to the clock used by the XOR engine. + +Example: + + xor0@400000 { + compatible = "marvell,xor-v2"; + reg = <0x400000 0x1000>, + <0x410000 0x1000>; + msi-parent = <&gic_v2m0>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt index 276ef815ef32..c075f5988135 100644 --- a/Documentation/devicetree/bindings/dma/mv-xor.txt +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -1,7 +1,10 @@ * Marvell XOR engines Required properties: -- compatible: Should be "marvell,orion-xor" or "marvell,armada-380-xor" +- compatible: Should be one of the following: + - "marvell,orion-xor" + - "marvell,armada-380-xor" + - "marvell,armada-3700-xor". - reg: Should contain registers location and length (two sets) the first set is the low registers, the second set the high registers for the XOR engine. diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt index c6908e7c42cc..c6908e7c42cc 100644 --- a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt +++ b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt diff --git a/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt new file mode 100644 index 000000000000..1e1dc8f972e4 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt @@ -0,0 +1,55 @@ +* NVIDIA Tegra Audio DMA (ADMA) controller + +The Tegra Audio DMA controller that is used for transferring data +between system memory and the Audio Processing Engine (APE). + +Required properties: +- compatible: Must be "nvidia,tegra210-adma". +- reg: Should contain DMA registers location and length. This should be + a single entry that includes all of the per-channel registers in one + contiguous bank. +- interrupt-parent: Phandle to the interrupt parent controller. +- interrupts: Should contain all of the per-channel DMA interrupts in + ascending order with respect to the DMA channel index. +- clocks: Must contain one entry for the ADMA module clock + (TEGRA210_CLK_D_AUDIO). +- clock-names: Must contain the name "d_audio" for the corresponding + 'clocks' entry. +- #dma-cells : Must be 1. The first cell denotes the receive/transmit + request number and should be between 1 and the maximum number of + requests supported. This value corresponds to the RX/TX_REQUEST_SELECT + fields in the ADMA_CHn_CTRL register. + + +Example: + +adma: dma@702e2000 { + compatible = "nvidia,tegra210-adma"; + reg = <0x0 0x702e2000 0x0 0x2000>; + interrupt-parent = <&tegra_agic>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_D_AUDIO>; + clock-names = "d_audio"; + #dma-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index 1c9d48ea4914..9cbf5d9df8fd 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -13,6 +13,8 @@ Required properties: - clock-names: must contain "bam_clk" entry - qcom,ee : indicates the active Execution Environment identifier (0-7) used in the secure world. +- qcom,controlled-remotely : optional, indicates that the bam is controlled by + remote proccessor i.e. execution environment. Example: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 5b902ac8d97e..5f2ce669789a 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -1,4 +1,4 @@ -* Renesas R-Car DMA Controller Device Tree bindings +* Renesas R-Car (RZ/G) DMA Controller Device Tree bindings Renesas R-Car Generation 2 SoCs have multiple multi-channel DMA controller instances named DMAC capable of serving multiple clients. Channels @@ -16,6 +16,8 @@ Required Properties: - compatible: "renesas,dmac-<soctype>", "renesas,rcar-dmac" as fallback. Examples with soctypes are: + - "renesas,dmac-r8a7743" (RZ/G1M) + - "renesas,dmac-r8a7745" (RZ/G1E) - "renesas,dmac-r8a7790" (R-Car H2) - "renesas,dmac-r8a7791" (R-Car M2-W) - "renesas,dmac-r8a7792" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index c261598164a7..0f5583293c9c 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -13,6 +13,11 @@ Required properties: - chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1: increase from chan n->0 - block_size: Maximum block size supported by the controller +- data-width: Maximum data width supported by hardware per AHB master + (in bytes, power of 2) + + +Deprecated properties: - data_width: Maximum data width supported by hardware per AHB master (0 - 8bits, 1 - 16bits, ..., 5 - 256bits) @@ -38,7 +43,7 @@ Example: chan_allocation_order = <1>; chan_priority = <1>; block_size = <0xfff>; - data_width = <3 3>; + data-width = <8 8>; }; DMA clients connected to the Designware DMA controller must use the format @@ -47,8 +52,8 @@ The four cells in order are: 1. A phandle pointing to the DMA controller 2. The DMA request line number -3. Source master for transfers on allocated channel -4. Destination master for transfers on allocated channel +3. Memory master for transfers on allocated channel +4. Peripheral master for transfers on allocated channel Example: diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt index d13c136cef8c..6b267045f522 100644 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -7,6 +7,7 @@ Required properties: - compatible: Must be one of "allwinner,sun6i-a31-dma" "allwinner,sun8i-a23-dma" + "allwinner,sun8i-a83t-dma" "allwinner,sun8i-h3-dma" - reg: Should contain the registers base address and length - interrupts: Should contain a reference to the interrupt used by this device diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 079b42a81d7c..18090e7226b4 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -15,7 +15,7 @@ Required properties: - reg: Memory map of eDMA CC - reg-names: "edma3_cc" - interrupts: Interrupt lines for CCINT, MPERR and CCERRINT. -- interrupt-names: "edma3_ccint", "emda3_mperr" and "edma3_ccerrint" +- interrupt-names: "edma3_ccint", "edma3_mperr" and "edma3_ccerrint" - ti,tptcs: List of TPTCs associated with the eDMA in the following form: <&tptc_phandle TC_priority_number>. The highest priority is 0. @@ -48,7 +48,7 @@ edma: edma@49000000 { reg = <0x49000000 0x10000>; reg-names = "edma3_cc"; interrupts = <12 13 14>; - interrupt-names = "edma3_ccint", "emda3_mperr", "edma3_ccerrint"; + interrupt-names = "edma3_ccint", "edma3_mperr", "edma3_ccerrint"; dma-requests = <64>; #dma-cells = <2>; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt index 2291c4098730..a2b8bfaec43c 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -1,46 +1,96 @@ +Xilinx AXI VDMA engine, it does transfers between memory and video devices. +It can be configured to have one channel or two channels. If configured +as two channels, one is to transmit to the video device and another is +to receive from the video device. + Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream target devices. It can be configured to have one channel or two channels. If configured as two channels, one is to transmit to the device and another is to receive from the device. +Xilinx AXI CDMA engine, it does transfers between memory-mapped source +address and a memory-mapped destination address. + Required properties: -- compatible: Should be "xlnx,axi-dma-1.00.a" +- compatible: Should be "xlnx,axi-vdma-1.00.a" or "xlnx,axi-dma-1.00.a" or + "xlnx,axi-cdma-1.00.a"" - #dma-cells: Should be <1>, see "dmas" property below -- reg: Should contain DMA registers location and length. -- dma-channel child node: Should have atleast one channel and can have upto +- reg: Should contain VDMA registers location and length. +- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits). +- dma-ranges: Should be as the following <dma_addr cpu_addr max_len>. +- dma-channel child node: Should have at least one channel and can have up to two channels per device. This node specifies the properties of each DMA channel (see child node properties below). +- clocks: Input clock specifier. Refer to common clock bindings. +- clock-names: List of input clocks + For VDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk" "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk" + For CDMA: + Required elements: "s_axi_lite_aclk", "m_axi_aclk" + FOR AXIDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axi_sg_aclk" + +Required properties for VDMA: +- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. Optional properties: -- xlnx,include-sg: Tells whether configured for Scatter-mode in +- xlnx,include-sg: Tells configured for Scatter-mode in the hardware. +Optional properties for AXI DMA: +- xlnx,mcdma: Tells whether configured for multi-channel mode in the hardware. +Optional properties for VDMA: +- xlnx,flush-fsync: Tells which channel to Flush on Frame sync. + It takes following values: + {1}, flush both channels + {2}, flush mm2s channel + {3}, flush s2mm channel Required child node properties: -- compatible: It should be either "xlnx,axi-dma-mm2s-channel" or +- compatible: + For VDMA: It should be either "xlnx,axi-vdma-mm2s-channel" or + "xlnx,axi-vdma-s2mm-channel". + For CDMA: It should be "xlnx,axi-cdma-channel". + For AXIDMA: It should be either "xlnx,axi-dma-mm2s-channel" or "xlnx,axi-dma-s2mm-channel". -- interrupts: Should contain per channel DMA interrupts. +- interrupts: Should contain per channel VDMA interrupts. - xlnx,datawidth: Should contain the stream data width, take values {32,64...1024}. -Option child node properties: -- xlnx,include-dre: Tells whether hardware is configured for Data +Optional child node properties: +- xlnx,include-dre: Tells hardware is configured for Data Realignment Engine. +Optional child node properties for VDMA: +- xlnx,genlock-mode: Tells Genlock synchronization is + enabled/disabled in hardware. +Optional child node properties for AXI DMA: +-dma-channels: Number of dma channels in child node. Example: ++++++++ -axi_dma_0: axidma@40400000 { - compatible = "xlnx,axi-dma-1.00.a"; +axi_vdma_0: axivdma@40030000 { + compatible = "xlnx,axi-vdma-1.00.a"; #dma_cells = <1>; - reg = < 0x40400000 0x10000 >; - dma-channel@40400000 { - compatible = "xlnx,axi-dma-mm2s-channel"; - interrupts = < 0 59 4 >; + reg = < 0x40030000 0x10000 >; + dma-ranges = <0x00000000 0x00000000 0x40000000>; + xlnx,num-fstores = <0x8>; + xlnx,flush-fsync = <0x1>; + xlnx,addrwidth = <0x20>; + clocks = <&clk 0>, <&clk 1>, <&clk 2>, <&clk 3>, <&clk 4>; + clock-names = "s_axi_lite_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk"; + dma-channel@40030000 { + compatible = "xlnx,axi-vdma-mm2s-channel"; + interrupts = < 0 54 4 >; xlnx,datawidth = <0x40>; } ; - dma-channel@40400030 { - compatible = "xlnx,axi-dma-s2mm-channel"; - interrupts = < 0 58 4 >; + dma-channel@40030030 { + compatible = "xlnx,axi-vdma-s2mm-channel"; + interrupts = < 0 53 4 >; xlnx,datawidth = <0x40>; } ; } ; @@ -49,7 +99,7 @@ axi_dma_0: axidma@40400000 { * DMA client Required properties: -- dmas: a list of <[DMA device phandle] [Channel ID]> pairs, +- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs, where Channel ID is '0' for write/tx and '1' for read/rx channel. - dma-names: a list of DMA channel names, one per "dmas" entry @@ -57,9 +107,9 @@ Required properties: Example: ++++++++ -dmatest_0: dmatest@0 { - compatible ="xlnx,axi-dma-test-1.00.a"; - dmas = <&axi_dma_0 0 - &axi_dma_0 1>; - dma-names = "dma0", "dma1"; +vdmatest_0: vdmatest@0 { + compatible ="xlnx,axi-vdma-test-1.00.a"; + dmas = <&axi_vdma_0 0 + &axi_vdma_0 1>; + dma-names = "vdma0", "vdma1"; } ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt deleted file mode 100644 index e4c4d47f8137..000000000000 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt +++ /dev/null @@ -1,75 +0,0 @@ -Xilinx AXI VDMA engine, it does transfers between memory and video devices. -It can be configured to have one channel or two channels. If configured -as two channels, one is to transmit to the video device and another is -to receive from the video device. - -Required properties: -- compatible: Should be "xlnx,axi-vdma-1.00.a" -- #dma-cells: Should be <1>, see "dmas" property below -- reg: Should contain VDMA registers location and length. -- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. -- dma-channel child node: Should have at least one channel and can have up to - two channels per device. This node specifies the properties of each - DMA channel (see child node properties below). - -Optional properties: -- xlnx,include-sg: Tells configured for Scatter-mode in - the hardware. -- xlnx,flush-fsync: Tells which channel to Flush on Frame sync. - It takes following values: - {1}, flush both channels - {2}, flush mm2s channel - {3}, flush s2mm channel - -Required child node properties: -- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or - "xlnx,axi-vdma-s2mm-channel". -- interrupts: Should contain per channel VDMA interrupts. -- xlnx,datawidth: Should contain the stream data width, take values - {32,64...1024}. - -Optional child node properties: -- xlnx,include-dre: Tells hardware is configured for Data - Realignment Engine. -- xlnx,genlock-mode: Tells Genlock synchronization is - enabled/disabled in hardware. - -Example: -++++++++ - -axi_vdma_0: axivdma@40030000 { - compatible = "xlnx,axi-vdma-1.00.a"; - #dma_cells = <1>; - reg = < 0x40030000 0x10000 >; - xlnx,num-fstores = <0x8>; - xlnx,flush-fsync = <0x1>; - dma-channel@40030000 { - compatible = "xlnx,axi-vdma-mm2s-channel"; - interrupts = < 0 54 4 >; - xlnx,datawidth = <0x40>; - } ; - dma-channel@40030030 { - compatible = "xlnx,axi-vdma-s2mm-channel"; - interrupts = < 0 53 4 >; - xlnx,datawidth = <0x40>; - } ; -} ; - - -* DMA client - -Required properties: -- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs, - where Channel ID is '0' for write/tx and '1' for read/rx - channel. -- dma-names: a list of DMA channel names, one per "dmas" entry - -Example: -++++++++ - -vdmatest_0: vdmatest@0 { - compatible ="xlnx,axi-vdma-test-1.00.a"; - dmas = <&axi_vdma_0 0 - &axi_vdma_0 1>; - dma-names = "vdma0", "vdma1"; -} ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt new file mode 100644 index 000000000000..a784cdd94790 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt @@ -0,0 +1,27 @@ +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, +memory to device and device to memory transfers. It also has flow +control and rate control support for slave/peripheral dma access. + +Required properties: +- compatible : Should be "xlnx,zynqmp-dma-1.0" +- reg : Memory map for gdma/adma module access. +- interrupt-parent : Interrupt controller the interrupt is routed through +- interrupts : Should contain DMA channel interrupt. +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 +- clock-names : List of input clocks "clk_main", "clk_apb" + (see clock bindings for details) + +Optional properties: +- dma-coherent : Present if dma operations are coherent. + +Example: +++++++++ +fpd_dma_chan1: dma@fd500000 { + compatible = "xlnx,zynqmp-dma-1.0"; + reg = <0x0 0xFD500000 0x1000>; + interrupt-parent = <&gic>; + interrupts = <0 117 4>; + clock-names = "clk_main", "clk_apb"; + xlnx,bus-width = <128>; + dma-coherent; +}; diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index e27341f8a4c7..7f3d94ae81ff 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -46,7 +46,8 @@ Optional properties: The second cell represents the MICBIAS to be used. The third cell represents the value of the micd-pol-gpio pin. - - wlf,gpsw : Settings for the general purpose switch + - wlf,gpsw : Settings for the general purpose switch, set as one of the + ARIZONA_GPSW_XXX defines. Example: diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt new file mode 100644 index 000000000000..35383adb10f1 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt @@ -0,0 +1,41 @@ +Qualcomm's PM8941 USB ID Extcon device + +Some Qualcomm PMICs have a "misc" module that can be used to detect when +the USB ID pin has been pulled low or high. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,pm8941-misc"; + +- reg: + Usage: required + Value type: <u32> + Definition: Should contain the offset to the misc address space + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the usb id interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the string "usb_id" for the usb id interrupt + +Example: + + pmic { + usb_id: misc@900 { + compatible = "qcom,pm8941-misc"; + reg = <0x900>; + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "usb_id"; + }; + } + + usb-controller { + extcon = <&usb_id>; + }; diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt new file mode 100644 index 000000000000..3b4436e56865 --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -0,0 +1,28 @@ +QCOM Secure Channel Manager (SCM) + +Qualcomm processors include an interface to communicate to the secure firmware. +This interface allows for clients to request different types of actions. These +can include CPU power up/down, HDCP requests, loading of firmware, and other +assorted actions. + +Required properties: +- compatible: must contain one of the following: + * "qcom,scm-apq8064" for APQ8064 platforms + * "qcom,scm-msm8660" for MSM8660 platforms + * "qcom,scm-msm8690" for MSM8690 platforms + * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc) +- clocks: One to three clocks may be required based on compatible. + * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960" + * Core, iface, and bus clocks required for "qcom,scm" +- clock-names: Must contain "core" for the core clock, "iface" for the interface + clock and "bus" for the bus clock per the requirements of the compatible. + +Example for MSM8916: + + firmware { + scm { + compatible = "qcom,scm"; + clocks = <&gcc GCC_CRYPTO_CLK> , <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>; + clock-names = "core", "bus", "iface"; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt new file mode 100644 index 000000000000..e7853143fa42 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt @@ -0,0 +1,46 @@ +Bindings for the Broadcom's brcm,bcm6345-gpio memory-mapped GPIO controllers. + +These bindings can be used on any BCM63xx SoC. However, BCM6338 and BCM6345 +are the only ones which don't need a pinctrl driver. +BCM6338 have 8-bit data and dirout registers, where GPIO state can be read +and/or written, and the direction changed from input to output. +BCM6345 have 16-bit data and dirout registers, where GPIO state can be read +and/or written, and the direction changed from input to output. + +Required properties: + - compatible: should be "brcm,bcm6345-gpio" + - reg-names: must contain + "dat" - data register + "dirout" - direction (output) register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - native-endian: use native endian memory. + +Examples: + - BCM6338: + gpio: gpio-controller@fffe0407 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0407 1>, <0xfffe040f 1>; + + #gpio-cells = <2>; + gpio-controller; + }; + + - BCM6345: + gpio: gpio-controller@fffe0406 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0406 2>, <0xfffe040a 2>; + native-endian; + + #gpio-cells = <2>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt index 94ae9f82dcf8..fd42e7280f72 100644 --- a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -1,7 +1,7 @@ * ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs Required properties: -- compatible: Should contain "cirrus,clps711x-mctrl-gpio". +- compatible: Should contain "cirrus,ep7209-mctrl-gpio". - gpio-controller: Marks the device node as a gpio controller. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify the gpio polarity: @@ -11,7 +11,7 @@ Required properties: Example: sysgpio: sysgpio { compatible = "cirrus,ep7312-mctrl-gpio", - "cirrus,clps711x-mctrl-gpio"; + "cirrus,ep7209-mctrl-gpio"; gpio-controller; #gpio-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt index cc2608021f26..ce1b2231bf5d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -1,7 +1,9 @@ * Generic 8-bits shift register GPIO driver Required properties: -- compatible : Should be "fairchild,74hc595" +- compatible: Should contain one of the following: + "fairchild,74hc595" + "nxp,74lvc594" - reg : chip select number - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt new file mode 100644 index 000000000000..393bb2ed8a77 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt @@ -0,0 +1,36 @@ +Aspeed GPIO controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Either "aspeed,ast2400-gpio" or "aspeed,ast2500-gpio" + +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify optional + parameters (unused) + +- reg : Address and length of the register set for the device +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt specifier (see interrupt bindings for + details) +- interrupt-controller : Mark the GPIO controller as an interrupt-controller + +Optional properties: + +- interrupt-parent : The parent interrupt controller, optional if inherited + +The gpio and interrupt properties are further described in their respective +bindings documentation: + +- Documentation/devicetree/bindings/gpio/gpio.txt +- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + + Example: + gpio@1e780000 { + #gpio-cells = <2>; + compatible = "aspeed,ast2400-gpio"; + gpio-controller; + interrupts = <20>; + reg = <0x1e780000 0x1000>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-axp209.txt b/Documentation/devicetree/bindings/gpio/gpio-axp209.txt new file mode 100644 index 000000000000..a6611304dd3c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-axp209.txt @@ -0,0 +1,30 @@ +AXP209 GPIO controller + +This driver follows the usual GPIO bindings found in +Documentation/devicetree/bindings/gpio/gpio.txt + +Required properties: +- compatible: Should be "x-powers,axp209-gpio" +- #gpio-cells: Should be two. The first cell is the pin number and the + second is the GPIO flags. +- gpio-controller: Marks the device node as a GPIO controller. + +This node must be a subnode of the axp20x PMIC, documented in +Documentation/devicetree/bindings/mfd/axp20x.txt + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + axp_gpio: gpio { + compatible = "x-powers,axp209-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt index e0d0446a6b78..0a304ad29d81 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -1,7 +1,7 @@ Cirrus Logic CLPS711X GPIO controller Required properties: -- compatible: Should be "cirrus,clps711x-gpio" +- compatible: Should be "cirrus,ep7209-gpio" - reg: Physical base GPIO controller registers location and length. There should be two registers, first is DATA register, the second is DIRECTION. @@ -21,7 +21,7 @@ aliases { }; porta: gpio@80000000 { - compatible = "cirrus,clps711x-gpio"; + compatible = "cirrus,ep7312-gpio","cirrus,ep7209-gpio"; reg = <0x80000000 0x1>, <0x80000040 0x1>; gpio-controller; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max77620.txt b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt new file mode 100644 index 000000000000..410e716fd3d2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt @@ -0,0 +1,25 @@ +GPIO driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Required properties: +------------------- +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +For more details, please refer generic GPIO DT binding document +<devicetree/bindings/gpio/gpio.txt>. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + compatible = "maxim,max77620"; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 120bc4971cf3..4b6cc632ca5c 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -1,9 +1,10 @@ -* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller +* Freescale MPC512x/MPC8xxx/QorIQ/Layerscape GPIO controller Required properties: - compatible : Should be "fsl,<soc>-gpio" The following <soc>s are known to be supported: - mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq, + ls1021a, ls1043a, ls2080a. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and @@ -15,7 +16,7 @@ Optional properties: - little-endian : GPIO registers are used as little endian. If not present registers are used as big endian by default. -Example: +Example of gpio-controller node for a mpc5125 SoC: gpio0: gpio@1100 { compatible = "fsl,mpc5125-gpio"; @@ -24,3 +25,16 @@ gpio0: gpio@1100 { interrupts = <78 0x8>; status = "okay"; }; + +Example of gpio-controller node for a ls2080a SoC: + +gpio0: gpio@2300000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 6b4a98f74be3..08dd15f89ba9 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -21,6 +21,7 @@ Required properties: maxim,max7313 maxim,max7315 ti,pca6107 + ti,pca9536 ti,tca6408 ti,tca6416 ti,tca6424 diff --git a/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt new file mode 100644 index 000000000000..1afc2de7a537 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt @@ -0,0 +1,16 @@ +TPIC2810 GPIO controller bindings + +Required properties: + - compatible : Should be "ti,tpic2810". + - reg : The I2C address of the device + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Example: + + gpio@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt b/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt deleted file mode 100644 index ba051074bedc..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt +++ /dev/null @@ -1,16 +0,0 @@ -* TPS65086 GPO Controller bindings - -Required properties: - - compatible : Should be "ti,tps65086-gpio". - - gpio-controller : Marks the device node as a GPIO Controller. - - #gpio-cells : Should be two. The first cell is the pin number - and the second cell is used to specify flags. - See ../gpio/gpio.txt for possible values. - -Example: - - gpio4: gpio { - compatible = "ti,tps65086-gpio"; - gpio-controller; - #gpio-cells = <2>; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt new file mode 100644 index 000000000000..3f8e71b1ab2a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt @@ -0,0 +1,30 @@ +* Technologic Systems I2C-FPGA's GPIO controller bindings + +This bindings describes the GPIO controller for Technologic's FPGA core. +TS-4900's FPGA encodes the GPIO state on 3 bits, whereas the TS-7970's FPGA +uses 2 bits: it doesn't use a dedicated input bit. + +Required properties: +- compatible: Should be one of the following + "technologic,ts4900-gpio" + "technologic,ts7970-gpio" +- reg: Physical base address of the controller and length + of memory mapped region. +- #gpio-cells: Should be two. The first cell is the pin number. +- gpio-controller: Marks the device node as a gpio controller. + +Optional property: +- ngpios: Number of GPIOs this controller is instantiated with, + the default is 32. See gpio.txt for more details. + +Example: + +&i2c2 { + gpio8: gpio@28 { + compatible = "technologic,ts4900-gpio"; + reg = <0x28>; + #gpio-cells = <2>; + gpio-controller; + ngpios = <32>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt index 262ee4ddf2cb..28662d83a43e 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt @@ -3,6 +3,8 @@ Netlogic XLP Family GPIO This GPIO driver is used for following Netlogic XLP SoCs: XLP832, XLP316, XLP208, XLP980, XLP532 +This GPIO driver is also compatible with GPIO controller found on +Broadcom Vulcan ARM64. Required properties: ------------------- @@ -13,6 +15,7 @@ Required properties: - "netlogic,xlp208-gpio": For Netlogic XLP208 - "netlogic,xlp980-gpio": For Netlogic XLP980 - "netlogic,xlp532-gpio": For Netlogic XLP532 + - "brcm,vulcan-gpio": For Broadcom Vulcan ARM64 - reg: Physical base address and length of the controller's registers. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 069cdf6f9dac..68d28f62a6f4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -131,6 +131,13 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Some system-on-chips (SoCs) use the concept of GPIO banks. A GPIO bank is an +instance of a hardware IP core on a silicon die, usually exposed to the +programmer as a coherent range of I/O addresses. Usually each such bank is +exposed in the device tree as an individual gpio-controller node, reflecting +the fact that the hardware was synthesized by reusing the same IP block a +few times over. + Optionally, a GPIO controller may have a "ngpios" property. This property indicates the number of in-use slots of available slots for GPIOs. The typical example is something like this: the hardware register is 32 bits @@ -145,6 +152,21 @@ additional bitmask is needed to specify which GPIOs are actually in use, and which are dummies. The bindings for this case has not yet been specified, but should be specified if/when such hardware appears. +Optionally, a GPIO controller may have a "gpio-line-names" property. This is +an array of strings defining the names of the GPIO lines going out of the +GPIO controller. This name should be the most meaningful producer name +for the system, such as a rail name indicating the usage. Package names +such as pin name are discouraged: such lines have opaque names (since they +are by definition generic purpose) and such names are usually not very +helpful. For example "MMC-CD", "Red LED Vdd" and "ethernet reset" are +reasonable line names as they describe what the line is used for. "GPIO0" +is not a good name to give to a GPIO line. Placeholders are discouraged: +rather use the "" (blank string) if the use of the GPIO line is undefined +in your design. The names are assigned starting from line offset 0 from +left to right from the passed array. An incomplete array (where the number +of passed named are less than ngpios) will still be used up until the last +provided valid line index. + Example: gpio-controller@00000000 { @@ -153,6 +175,10 @@ gpio-controller@00000000 { gpio-controller; #gpio-cells = <2>; ngpios = <18>; + gpio-line-names = "MMC-CD", "MMC-WP", "VDD eth", "RST eth", "LED R", + "LED G", "LED B", "Col A", "Col B", "Col C", "Col D", + "Row A", "Row B", "Row C", "Row D", "NMI button", + "poweroff", "reset"; } The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt new file mode 100644 index 000000000000..928ed4f43907 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -0,0 +1,47 @@ +* Oxford Semiconductor OXNAS SoC GPIO Controller + +Please refer to gpio.txt for generic information regarding GPIO bindings. + +Required properties: + - compatible: "oxsemi,ox810se-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - gpio-ranges: Interaction with the PINCTRL subsystem, it also specifies the + gpio base and count, should be in the format of numeric-gpio-range as + specified in the gpio.txt file. + +Example: + +gpio0: gpio@0 { + compatible = "oxsemi,ox810se-gpio"; + reg = <0x000000 0x100000>; + interrupts = <21>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pinctrl 0 0 32>; +}; + +keys { + ... + + button-esc { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt new file mode 100644 index 000000000000..d58b3958f3ea --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt @@ -0,0 +1,24 @@ +* IBM/AMCC/APM GPIO Controller for PowerPC 4XX series and compatible SoCs + +All GPIOs are pin-shared with other functions. DCRs control whether a +particular pin that has GPIO capabilities acts as a GPIO or is used for +another purpose. GPIO outputs are separately programmable to emulate +an open-drain driver. + +Required properties: + - compatible: must be "ibm,ppc4xx-gpio" + - reg: address and length of the register set for the device + - #gpio-cells: must be set to 2. The first cell is the pin number + and the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: marks the device node as a gpio controller. + +Example: + +GPIO0: gpio@ef600b00 { + compatible = "ibm,ppc4xx-gpio"; + reg = <0xef600b00 0x00000048>; + #gpio-cells = <2>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt index ef3752889496..dd031fc93b55 100644 --- a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -33,7 +33,7 @@ gpio0: gpio0@1f860000 { gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&PBCLK4>; + clocks = <&rootclk PB4CLK>; microchip,gpio-bank = <0>; gpio-ranges = <&pic32_pinctrl 0 0 16>; }; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 98d198396956..c3d016532d8e 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -44,26 +44,3 @@ Example for a PXA3xx platform: interrupt-controller; #interrupt-cells = <0x2>; }; - -* Marvell Orion GPIO Controller - -Required properties: -- compatible : Should be "marvell,orion-gpio" -- reg : Address and length of the register set for controller. -- gpio-controller : So we know this is a gpio controller. -- ngpio : How many gpios this controller has. -- interrupts : Up to 4 Interrupts for the controller. - -Optional properties: -- mask-offset : For SMP Orions, offset for Nth CPU - -Example: - - gpio0: gpio@10100 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0x10100 0x40>; - ngpio = <32>; - interrupts = <35>, <36>, <37>, <38>; - }; diff --git a/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt new file mode 100644 index 000000000000..c82a2e221bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt @@ -0,0 +1,161 @@ +NVIDIA Tegra186 GPIO controllers + +Tegra186 contains two GPIO controllers; a main controller and an "AON" +controller. This binding document applies to both controllers. The register +layouts for the controllers share many similarities, but also some significant +differences. Hence, this document describes closely related but different +bindings and compatible values. + +The Tegra186 GPIO controller allows software to set the IO direction of, and +read/write the value of, numerous GPIO signals. Routing of GPIO signals to +package balls is under the control of a separate pin controller HW block. Two +major sets of registers exist: + +a) Security registers, which allow configuration of allowed access to the GPIO +register set. These registers exist in a single contiguous block of physical +address space. The size of this block, and the security features available, +varies between the different GPIO controllers. + +Access to this set of registers is not necessary in all circumstances. Code +that wishes to configure access to the GPIO registers needs access to these +registers to do so. Code which simply wishes to read or write GPIO data does not +need access to these registers. + +b) GPIO registers, which allow manipulation of the GPIO signals. In some GPIO +controllers, these registers are exposed via multiple "physical aliases" in +address space, each of which access the same underlying state. See the hardware +documentation for rationale. Any particular GPIO client is expected to access +just one of these physical aliases. + +Tegra HW documentation describes a unified naming convention for all GPIOs +implemented by the SoC. Each GPIO is assigned to a port, and a port may control +a number of GPIOs. Thus, each GPIO is named according to an alphabetical port +name and an integer GPIO name within the port. For example, GPIO_PA0, GPIO_PN6, +or GPIO_PCC3. + +The number of ports implemented by each GPIO controller varies. The number of +implemented GPIOs within each port varies. GPIO registers within a controller +are grouped and laid out according to the port they affect. + +The mapping from port name to the GPIO controller that implements that port, and +the mapping from port name to register offset within a controller, are both +extremely non-linear. The header file <dt-bindings/gpio/tegra186-gpio.h> +describes the port-level mapping. In that file, the naming convention for ports +matches the HW documentation. The values chosen for the names are alphabetically +sorted within a particular controller. Drivers need to map between the DT GPIO +IDs and HW register offsets using a lookup table. + +Each GPIO controller can generate a number of interrupt signals. Each signal +represents the aggregate status for all GPIOs within a set of ports. Thus, the +number of interrupt signals generated by a controller varies as a rough function +of the number of ports it implements. Note that the HW documentation refers to +both the overall controller HW module and the sets-of-ports as "controllers". + +Each GPIO controller in fact generates multiple interrupts signals for each set +of ports. Each GPIO may be configured to feed into a specific one of the +interrupt signals generated by a set-of-ports. The intent is for each generated +signal to be routed to a different CPU, thus allowing different CPUs to each +handle subsets of the interrupts within a port. The status of each of these +per-port-set signals is reported via a separate register. Thus, a driver needs +to know which status register to observe. This binding currently defines no +configuration mechanism for this. By default, drivers should use register +GPIO_${port}_INTERRUPT_STATUS_G1_0. Future revisions to the binding could +define a property to configure this. + +Required properties: +- compatible + Array of strings. + One of: + - "nvidia,tegra186-gpio". + - "nvidia,tegra186-gpio-aon". +- reg-names + Array of strings. + Contains a list of names for the register spaces described by the reg + property. May contain the following entries, in any order: + - "gpio": Mandatory. GPIO control registers. This may cover either: + a) The single physical alias that this OS should use. + b) All physical aliases that exist in the controller. This is + appropriate when the OS is responsible for managing assignment of + the physical aliases. + - "security": Optional. Security configuration registers. + Users of this binding MUST look up entries in the reg property by name, + using this reg-names property to do so. +- reg + Array of (physical base address, length) tuples. + Must contain one entry per entry in the reg-names property, in a matching + order. +- interrupts + Array of interrupt specifiers. + The interrupt outputs from the HW block, one per set of ports, in the + order the HW manual describes them. The number of entries required varies + depending on compatible value: + - "nvidia,tegra186-gpio": 6 entries. + - "nvidia,tegra186-gpio-aon": 1 entry. +- gpio-controller + Boolean. + Marks the device node as a GPIO controller/provider. +- #gpio-cells + Single-cell integer. + Must be <2>. + Indicates how many cells are used in a consumer's GPIO specifier. + In the specifier: + - The first cell is the pin number. + See <dt-bindings/gpio/tegra186-gpio.h>. + - The second cell contains flags: + - Bit 0 specifies polarity + - 0: Active-high (normal). + - 1: Active-low (inverted). +- interrupt-controller + Boolean. + Marks the device node as an interrupt controller/provider. +- #interrupt-cells + Single-cell integer. + Must be <2>. + Indicates how many cells are used in a consumer's interrupt specifier. + In the specifier: + - The first cell is the GPIO number. + See <dt-bindings/gpio/tegra186-gpio.h>. + - The second cell is contains flags: + - Bits [3:0] indicate trigger type and level: + - 1: Low-to-high edge triggered. + - 2: High-to-low edge triggered. + - 4: Active high level-sensitive. + - 8: Active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +gpio@2200000 { + compatible = "nvidia,tegra186-gpio"; + reg-names = "security", "gpio"; + reg = + <0x0 0x2200000 0x0 0x10000>, + <0x0 0x2210000 0x0 0x10000>; + interrupts = + <0 47 IRQ_TYPE_LEVEL_HIGH>, + <0 50 IRQ_TYPE_LEVEL_HIGH>, + <0 53 IRQ_TYPE_LEVEL_HIGH>, + <0 56 IRQ_TYPE_LEVEL_HIGH>, + <0 59 IRQ_TYPE_LEVEL_HIGH>, + <0 180 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +gpio@c2f0000 { + compatible = "nvidia,tegra186-gpio-aon"; + reg-names = "security", "gpio"; + reg = + <0x0 0xc2f0000 0x0 0x1000>, + <0x0 0xc2f1000 0x0 0x1000>; + interrupts = + <0 60 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f60e2f477e93..7c1ab3b3254f 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -7,9 +7,11 @@ Required Properties: - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. + - "renesas,gpio-r8a7792": for R8A7792 (R-Car V2H) compatible GPIO controller. - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. + - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. - "renesas,gpio-rcar": for generic R-Car GPIO controller. - reg: Base address and length of each memory resource used by the GPIO diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt new file mode 100644 index 000000000000..038c3a6a1f4d --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt @@ -0,0 +1,38 @@ +Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers. + +The Western Digital MyBook Live has two memory-mapped GPIO controllers. +Both GPIO controller only have a single 8-bit data register, where GPIO +state can be read and/or written. + +Required properties: + - compatible: should be "wd,mbl-gpio" + - reg-names: must contain + "dat" - data register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - no-output: GPIOs are read-only. + +Examples: + gpio0: gpio0@e0000000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0000000 0x1>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio1: gpio1@e0100000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0100000 0x1>; + #gpio-cells = <2>; + gpio-controller; + no-output; + }; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt index 23bfe8e1f7cc..ff3db65e50de 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt @@ -1,9 +1,10 @@ -NVIDIA GK20A Graphics Processing Unit +NVIDIA Tegra Graphics Processing Units Required properties: -- compatible: "nvidia,<chip>-<gpu>" +- compatible: "nvidia,<gpu>" Currently recognized values: - - nvidia,tegra124-gk20a + - nvidia,gk20a + - nvidia,gm20b - reg: Physical base address and length of the controller's registers. Must contain two entries: - first entry for bar0 @@ -19,14 +20,20 @@ Required properties: - clock-names: Must include the following entries: - gpu - pwr +If the compatible string is "nvidia,gm20b", then the following clock +is also required: + - ref - resets: Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. - reset-names: Must include the following entries: - gpu -Example: +Optional properties: +- iommus: A reference to the IOMMU. See ../iommu/iommu.txt for details. - gpu@0,57000000 { +Example for GK20A: + + gpu@57000000 { compatible = "nvidia,gk20a"; reg = <0x0 0x57000000 0x0 0x01000000>, <0x0 0x58000000 0x0 0x01000000>; @@ -39,5 +46,25 @@ Example: clock-names = "gpu", "pwr"; resets = <&tegra_car 184>; reset-names = "gpu"; + iommus = <&mc TEGRA_SWGROUP_GPU>; + status = "disabled"; + }; + +Example for GM20B: + + gpu@57000000 { + compatible = "nvidia,gm20b"; + reg = <0x0 0x57000000 0x0 0x01000000>, + <0x0 0x58000000 0x0 0x01000000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "stall", "nonstall"; + clocks = <&tegra_car TEGRA210_CLK_GPU>, + <&tegra_car TEGRA210_CLK_PLL_P_OUT5>, + <&tegra_car TEGRA210_CLK_PLL_G_REF>; + clock-names = "gpu", "pwr", "ref"; + resets = <&tegra_car 184>; + reset-names = "gpu"; + iommus = <&mc TEGRA_SWGROUP_GPU>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt new file mode 100644 index 000000000000..59b38557f1bb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt @@ -0,0 +1,14 @@ +APM X-Gene hwmon driver + +APM X-Gene SOC sensors are accessed over the "SLIMpro" mailbox. + +Required properties : + - compatible : should be "apm,xgene-slimpro-hwmon" + - mboxes : use the label reference for the mailbox as the first parameter. + The second parameter is the channel number. + +Example : + hwmonslimpro { + compatible = "apm,xgene-slimpro-hwmon"; + mboxes = <&mailbox 7>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ina2xx.txt b/Documentation/devicetree/bindings/hwmon/ina2xx.txt index 9bcd5e87830d..02af0d94e921 100644 --- a/Documentation/devicetree/bindings/hwmon/ina2xx.txt +++ b/Documentation/devicetree/bindings/hwmon/ina2xx.txt @@ -7,6 +7,7 @@ Required properties: - "ti,ina220" for ina220 - "ti,ina226" for ina226 - "ti,ina230" for ina230 + - "ti,ina231" for ina231 - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/hwmon/jc42.txt b/Documentation/devicetree/bindings/hwmon/jc42.txt new file mode 100644 index 000000000000..07a250498fbb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/jc42.txt @@ -0,0 +1,42 @@ +Properties for Jedec JC-42.4 compatible temperature sensors + +Required properties: +- compatible: May include a device-specific string consisting of the + manufacturer and the name of the chip. A list of supported + chip names follows. + Must include "jedec,jc-42.4-temp" for any Jedec JC-42.4 + compatible temperature sensor. + + Supported chip names: + adi,adt7408 + atmel,at30ts00 + atmel,at30tse004 + onnn,cat6095 + onnn,cat34ts02 + maxim,max6604 + microchip,mcp9804 + microchip,mcp9805 + microchip,mcp9808 + microchip,mcp98243 + microchip,mcp98244 + microchip,mcp9843 + nxp,se97 + nxp,se98 + st,stts2002 + st,stts2004 + st,stts3000 + st,stts424 + st,stts424e + idt,tse2002 + idt,tse2004 + idt,ts3000 + idt,ts3001 + +- reg: I2C address + +Example: + +temp-sensor@1a { + compatible = "jedec,jc-42.4-temp"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc4151.txt b/Documentation/devicetree/bindings/hwmon/ltc4151.txt new file mode 100644 index 000000000000..d008a5ef525a --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc4151.txt @@ -0,0 +1,18 @@ +LTC4151 High Voltage I2C Current and Voltage Monitor + +Required properties: +- compatible: Must be "lltc,ltc4151" +- reg: I2C address + +Optional properties: +- shunt-resistor-micro-ohms + Shunt resistor value in micro-Ohms + Defaults to <1000> if unset. + +Example: + +ltc4151@6e { + compatible = "lltc,ltc4151"; + reg = <0x6e>; + shunt-resistor-micro-ohms = <1500>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/max6650.txt b/Documentation/devicetree/bindings/hwmon/max6650.txt new file mode 100644 index 000000000000..f6bd87d8e284 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/max6650.txt @@ -0,0 +1,28 @@ +Bindings for MAX6651 and MAX6650 I2C fan controllers + +Reference: +[1] https://datasheets.maximintegrated.com/en/ds/MAX6650-MAX6651.pdf + +Required properties: +- compatible : One of "maxim,max6650" or "maxim,max6651" +- reg : I2C address, one of 0x1b, 0x1f, 0x4b, 0x48. + +Optional properties, default is to retain the chip's current setting: +- maxim,fan-microvolt : The supply voltage of the fan, either 5000000 uV or + 12000000 uV. +- maxim,fan-prescale : Pre-scaling value, as per datasheet [1]. Lower values + allow more fine-grained control of slower fans. + Valid: 1, 2, 4, 8, 16. +- maxim,fan-target-rpm: Initial requested fan rotation speed. If specified, the + driver selects closed-loop mode and the requested speed. + This ensures the fan is already running before userspace + takes over. + +Example: + fan-max6650: max6650@1b { + reg = <0x1b>; + compatible = "maxim,max6650"; + maxim,fan-microvolt = <12000000>; + maxim,fan-prescale = <4>; + maxim,fan-target-rpm = <1200>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index bfeabb843941..71191ff0e781 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -44,8 +44,8 @@ Required properties: - our-claim-gpio: The GPIO that we use to claim the bus. - their-claim-gpios: The GPIOs that the other sides use to claim the bus. Note that some implementations may only support a single other master. -- Standard I2C mux properties. See mux.txt in this directory. -- Single I2C child bus node at reg 0. See mux.txt in this directory. +- Standard I2C mux properties. See i2c-mux.txt in this directory. +- Single I2C child bus node at reg 0. See i2c-mux.txt in this directory. Optional properties: - slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us. diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt index 6078aefe7ed4..7ce23ac61308 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -27,7 +27,8 @@ Required properties: - i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C parents. -Furthermore, I2C mux properties and child nodes. See mux.txt in this directory. +Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this +directory. Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt index 66709a825541..21da3ecbb370 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -22,8 +22,8 @@ Required properties: - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. - mux-gpios: list of gpios used to control the muxer -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - idle-state: value to set the muxer to when idle. When no value is @@ -33,7 +33,7 @@ For each i2c child node, an I2C child bus will be created. They will be numbered based on their order in the device tree. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output using the list of +in the relevant node's reg property will be output using the list of GPIOs, the first in the list holding the least-significant value. If an idle state is defined, using the idle-state (optional) property, diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt index ae8af1694e95..33119a98e144 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -28,9 +28,9 @@ Also required are: * Standard pinctrl properties that specify the pin mux state for each child bus. See ../pinctrl/pinctrl-bindings.txt. -* Standard I2C mux properties. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. For each named state defined in the pinctrl-names property, an I2C child bus will be created. I2C child bus numbers are assigned based on the index into diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt index 688783fbe696..de00d7fc450b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt @@ -7,8 +7,8 @@ Required properties: - compatible: i2c-mux-reg - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - reg: this pair of <offset size> specifies the register to control the mux. @@ -24,7 +24,7 @@ Optional properties: given, it defaults to the last value used. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output to the register. +in the relevant node's reg property will be output to the register. If an idle state is defined, using the idle-state (optional) property, whenever an access is not being made to a device on a child bus, the diff --git a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt index dced82ebe31d..872d485dffab 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt @@ -4,6 +4,12 @@ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + or + + compatible: "cavium,octeon-7890-twsi" + + Compatibility with cn78XX SOCs. + - reg: The base address of the TWSI/I2C bus controller register bank. - #address-cells: Must be <1>. diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index cf8bfc956cdc..5f0cb502b1db 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -19,6 +19,9 @@ Optional properties: - clock-frequency: desired I2C bus clock frequency in Hz. The absence of this property indicates the default frequency 100 kHz. - clocks: clock specifier. +- dmas: Must contain a list of two references to DMA specifiers, one for + transmission, and one for reception. +- dma-names: Must contain a list of two DMA names, "tx" and "rx". - i2c-scl-falling-time-ns: see i2c.txt - i2c-scl-internal-delay-ns: see i2c.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index 0b4a85fe2d86..bbc5a1ed5fa1 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -6,10 +6,20 @@ RK3xxx SoCs. Required properties : - reg : Offset and length of the register set for the device - - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c", - "rockchip,rk3228-i2c" or "rockchip,rk3288-i2c". + - compatible: should be one of the following: + - "rockchip,rk3066-i2c": for rk3066 + - "rockchip,rk3188-i2c": for rk3188 + - "rockchip,rk3228-i2c": for rk3228 + - "rockchip,rk3288-i2c": for rk3288 + - "rockchip,rk3399-i2c": for rk3399 - interrupts : interrupt number - - clocks : parent clock + - clocks: See ../clock/clock-bindings.txt + - For older hardware (rk3066, rk3188, rk3228, rk3288): + - There is one clock that's used both to derive the functional clock + for the device and as the bus clock. + - For newer hardware (rk3399): specified by name + - "i2c": This is used to derive the functional clock. + - "pclk": This is the bus clock. Required on RK3066, RK3188 : diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index c8d977ed847f..f31b2ad1552b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -62,6 +62,13 @@ wants to support one of the below features, it should adapt the bindings below. - wakeup-source device can be used as a wakeup source. +- reg + I2C slave addresses + +- reg-names + Names of map programmable addresses. + It can contain any map needing another address than default one. + Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first interrupt if not using interrupt names) as primary interrupt for the slave. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 539874490492..1416c6a0d2cd 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -38,6 +38,7 @@ dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors +domintech,dmard09 DMARD09: 3-axis Accelerometer epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE @@ -56,12 +57,78 @@ maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +mcube,mc3230 mCube 3-axis 8-bit digital accelerometer +microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4531-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4532-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4532-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4532-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4532-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4541-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4541-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4541-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4541-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4542-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4542-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4542-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4542-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4551-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4551-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4551-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4551-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4552-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4552-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4552-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4552-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4561-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4561-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4561-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4561-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4562-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4562-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4562-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4562-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4631-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4631-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4631-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4631-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4632-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4632-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4632-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4632-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4641-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4641-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4641-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4641-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4642-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4642-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4642-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4642-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4651-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4651-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4651-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4651-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4652-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4652-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4652-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4652-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4661-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4661-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4661-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4661-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4662-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4662-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4662-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4662-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor national,lm85 Temperature sensor with integrated fan control national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface nuvoton,npct501 i2c trusted platform module (TPM) +nuvoton,npct601 i2c trusted platform module (TPM2) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar @@ -81,10 +148,10 @@ samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply -st-micro,24c256 i2c serial eeprom (24cxx) -stm,m41t00 Serial Access TIMEKEEPER -stm,m41t62 Serial real-time clock (RTC) with alarm -stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +st,24c256 i2c serial eeprom (24cxx) +st,m41t00 Serial real-time clock (RTC) +st,m41t62 Serial real-time clock (RTC) with alarm +st,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,ads7828 8-Channels, 12-bit ADC ti,ads7830 8-Channels, 8-bit ADC diff --git a/Documentation/devicetree/bindings/iio/accel/dmard06.txt b/Documentation/devicetree/bindings/iio/accel/dmard06.txt new file mode 100644 index 000000000000..ce105a12c645 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/dmard06.txt @@ -0,0 +1,19 @@ +Device tree bindings for Domintech DMARD05, DMARD06, DMARD07 accelerometers + +Required properties: + - compatible : Should be "domintech,dmard05" + or "domintech,dmard06" + or "domintech,dmard07" + - reg : I2C address of the chip. Should be 0x1c + +Example: + &i2c1 { + /* ... */ + + accelerometer@1c { + compatible = "domintech,dmard06"; + reg = <0x1c>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt new file mode 100644 index 000000000000..b25bf3a77e0f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt @@ -0,0 +1,22 @@ +Kionix KXSD9 Accelerometer device tree bindings + +Required properties: + - compatible: should be set to "kionix,kxsd9" + - reg: i2c slave address + +Optional properties: + - vdd-supply: The input supply for VDD + - iovdd-supply: The input supply for IOVDD + - interrupts: The movement detection interrupt + - mount-matrix: See mount-matrix.txt + +Example: + +kxsd9@18 { + compatible = "kionix,kxsd9"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <57 IRQ_TYPE_EDGE_FALLING>; + iovdd-supply = <&bar>; + vdd-supply = <&baz>; +}; diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 165937e1ac1c..45f5c5c5929c 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -1,4 +1,4 @@ -Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC +Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC, MMA8653FC or FXLS8471Q triaxial accelerometer Required properties: @@ -9,6 +9,7 @@ Required properties: * "fsl,mma8453" * "fsl,mma8652" * "fsl,mma8653" + * "fsl,fxls8471" - reg: the I2C address of the chip diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt index 0f813dec5e08..f65b04fb7962 100644 --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -59,28 +59,24 @@ adc0: adc@fffb0000 { atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "lowres"; - trigger@0 { - reg = <0>; + trigger0 { trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; - trigger@1 { - reg = <1>; + trigger1 { trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; - trigger@2 { - reg = <2>; + trigger2 { trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; - trigger@3 { - reg = <3>; + trigger3 { trigger-name = "continuous"; trigger-value = <0x6>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt new file mode 100644 index 000000000000..caaaed765ce4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt @@ -0,0 +1,41 @@ +* Broadcom's IPROC Static ADC controller + +Broadcom iProc ADC controller has 8 channels 10bit ADC. +Allows user to convert analog input voltage values to digital. + +Required properties: + +- compatible: Must be "brcm,iproc-static-adc" + +- adc-syscon: Handler of syscon node defining physical base address of the + controller and length of memory mapped region. + +- #io-channel-cells = <1>; As ADC has multiple outputs + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- io-channel-ranges: + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- clocks: Clock used for this block. + +- clock-names: Clock name should be given as tsc_clk. + +- interrupts: interrupt line number. + +For example: + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + adc: adc@180a6000 { + compatible = "brcm,iproc-static-adc"; + adc-syscon = <&ts_adc_syscon>; + #io-channel-cells = <1>; + io-channel-ranges; + clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt new file mode 100644 index 000000000000..0bcae5140bc5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt @@ -0,0 +1,21 @@ +NXP LPC1850 ADC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-adc" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: + +adc0: adc@400e3000 { + compatible = "nxp,lpc1850-adc"; + reg = <0x400e3000 0x1000>; + interrupts = <17>; + clocks = <&ccu1 CLK_APB3_ADC0>; + vref-supply = <®_vdda>; + resets = <&rgu 40>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/max1363.txt b/Documentation/devicetree/bindings/iio/adc/max1363.txt new file mode 100644 index 000000000000..94a9011dd860 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1363.txt @@ -0,0 +1,63 @@ +* Maxim 1x3x/136x/116xx Analog to Digital Converter (ADC) + +The node for this driver must be a child node of a I2C controller, hence +all mandatory properties for your controller must be specified. See directory: + + Documentation/devicetree/bindings/i2c + +for more details. + +Required properties: + - compatible: Should be one of + "maxim,max1361" + "maxim,max1362" + "maxim,max1363" + "maxim,max1364" + "maxim,max1036" + "maxim,max1037" + "maxim,max1038" + "maxim,max1039" + "maxim,max1136" + "maxim,max1137" + "maxim,max1138" + "maxim,max1139" + "maxim,max1236" + "maxim,max1237" + "maxim,max1238" + "maxim,max1239" + "maxim,max11600" + "maxim,max11601" + "maxim,max11602" + "maxim,max11603" + "maxim,max11604" + "maxim,max11605" + "maxim,max11606" + "maxim,max11607" + "maxim,max11608" + "maxim,max11609" + "maxim,max11610" + "maxim,max11611" + "maxim,max11612" + "maxim,max11613" + "maxim,max11614" + "maxim,max11615" + "maxim,max11616" + "maxim,max11617" + "maxim,max11644" + "maxim,max11645" + "maxim,max11646" + "maxim,max11647" + - reg: Should contain the ADC I2C address + +Optional properties: + - vcc-supply: phandle to the regulator that provides power to the ADC. + - vref-supply: phandle to the regulator for ADC reference voltage. + - interrupts: IRQ line for the ADC. If not used the driver will use + polling. + +Example: +adc: max11644@36 { + compatible = "maxim,max11644"; + reg = <0x36>; + vref-supply = <&adc_vref>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt new file mode 100644 index 000000000000..68c45cbbe3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -0,0 +1,29 @@ +* Mediatek AUXADC - Analog to Digital Converter on Mediatek mobile soc (mt65xx/mt81xx/mt27xx) +=============== + +The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found +in some Mediatek SoCs which among other things measures the temperatures +in the SoC. It can be used directly with register accesses, but it is also +used by thermal controller which reads the temperatures from the AUXADC +directly via its own bus interface. See +Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +for the Thermal Controller which holds a phandle to the AUXADC. + +Required properties: + - compatible: Should be one of: + - "mediatek,mt2701-auxadc": For MT2701 family of SoCs + - "mediatek,mt8173-auxadc": For MT8173 family of SoCs + - reg: Address range of the AUXADC unit. + - clocks: Should contain a clock specifier for each entry in clock-names + - clock-names: Should contain "main". + - #io-channel-cells: Should be 1, see ../iio-bindings.txt + +Example: + +auxadc: adc@11001000 { + compatible = "mediatek,mt2701-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&pericfg CLK_PERI_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt index 555fb117d4fa..555fb117d4fa 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt index a9a5fe19ff2a..205593f56fe7 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -1,7 +1,11 @@ Rockchip Successive Approximation Register (SAR) A/D Converter bindings Required properties: -- compatible: Should be "rockchip,saradc" or "rockchip,rk3066-tsadc" +- compatible: should be "rockchip,<name>-saradc" or "rockchip,rk3066-tsadc" + - "rockchip,saradc": for rk3188, rk3288 + - "rockchip,rk3066-tsadc": for rk3036 + - "rockchip,rk3399-saradc": for rk3399 + - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format @@ -12,6 +16,11 @@ Required properties: - vref-supply: The regulator supply ADC reference voltage. - #io-channel-cells: Should be 1, see ../iio-bindings.txt +Optional properties: +- resets: Must contain an entry for each entry in reset-names if need support + this option. See ../reset/reset.txt for details. +- reset-names: Must include the name "saradc-apb". + Example: saradc: saradc@2006c000 { compatible = "rockchip,saradc"; @@ -19,6 +28,8 @@ Example: interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; clock-names = "saradc", "apb_pclk"; + resets = <&cru SRST_SARADC>; + reset-names = "saradc-apb"; #io-channel-cells = <1>; vref-supply = <&vcc18>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt new file mode 100644 index 000000000000..049a1d36f013 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt @@ -0,0 +1,37 @@ +* Texas Instruments' ADC12130/ADC12132/ADC12138 + +Required properties: + - compatible: Should be one of + * "ti,adc12130" + * "ti,adc12132" + * "ti,adc12138" + - reg: SPI chip select number for the device + - interrupts: Should contain interrupt for EOC (end of conversion) + - clocks: phandle to conversion clock input + - spi-max-frequency: Definision as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - vref-p-supply: The regulator supply for positive analog voltage reference + +Optional properties: + - vref-n-supply: The regulator supply for negative analog voltage reference + (Note that this must not go below GND or exceed vref-p) + If not specified, this is assumed to be analog ground. + - ti,acquisition-time: The number of conversion clock periods for the S/H's + acquisition time. Should be one of 6, 10, 18, 34. If not specified, + default value of 10 is used. + For high source impedances, this value can be increased to 18 or 34. + For less ADC accuracy and/or slower CCLK frequencies this value may be + decreased to 6. See section 6.0 INPUT SOURCE RESISTANCE in the + datasheet for details. + +Example: +adc@0 { + compatible = "ti,adc12138"; + reg = <0>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio1>; + clocks = <&cclk>; + vref-p-supply = <&ldo4_reg>; + spi-max-frequency = <5000000>; + ti,acquisition-time = <6>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt new file mode 100644 index 000000000000..9ed2315781e4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt @@ -0,0 +1,16 @@ +* Texas Instruments ADC141S626 and ADC161S626 chips + +Required properties: + - compatible: Should be "ti,adc141s626" or "ti,adc161s626" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc161s626"; + reg = <0>; + spi-max-frequency = <4300000>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt new file mode 100644 index 000000000000..2962bd9a2b3d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific EC-SM OEM sensor + +http://www.atlas-scientific.com/_files/_datasheets/_oem/EC_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,ec-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@64 { + compatible = "atlas,ec-sm"; + reg = <0x64>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt new file mode 100644 index 000000000000..5d8b687d5edc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific ORP-SM OEM sensor + +https://www.atlas-scientific.com/_files/_datasheets/_oem/ORP_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,orp-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@66 { + compatible = "atlas,orp-sm"; + reg = <0x66>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5592r.txt b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt new file mode 100644 index 000000000000..989f96f31c66 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt @@ -0,0 +1,155 @@ +Analog Devices AD5592R/AD5593R DAC/ADC device driver + +Required properties for the AD5592R: + - compatible: Must be "adi,ad5592r" + - reg: SPI chip select number for the device + - spi-max-frequency: Max SPI frequency to use (< 30000000) + - spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode + +Required properties for the AD5593R: + - compatible: Must be "adi,ad5593r" + - reg: I2C address of the device + +Required properties for all supported chips: + - #address-cells: Should be 1. + - #size-cells: Should be 0. + - channel nodes: + Each child node represents one channel and has the following + Required properties: + * reg: Pin on which this channel is connected to. + * adi,mode: Mode or function of this channel. + Macros specifying the valid values + can be found in <dt-bindings/iio/adi,ad5592r.h>. + + The following values are currently supported: + * CH_MODE_UNUSED (the pin is unused) + * CH_MODE_ADC (the pin is ADC input) + * CH_MODE_DAC (the pin is DAC output) + * CH_MODE_DAC_AND_ADC (the pin is DAC output + but can be monitored by an ADC, since + there is no disadvantage this + this should be considered as the + preferred DAC mode) + * CH_MODE_GPIO (the pin is registered + with GPIOLIB) + Optional properties: + * adi,off-state: State of this channel when unused or the + device gets removed. Macros specifying the + valid values can be found in + <dt-bindings/iio/adi,ad5592r.h>. + + * CH_OFFSTATE_PULLDOWN (the pin is pulled down) + * CH_OFFSTATE_OUT_LOW (the pin is output low) + * CH_OFFSTATE_OUT_HIGH (the pin is output high) + * CH_OFFSTATE_OUT_TRISTATE (the pin is + tristated output) + + +Optional properties: + - vref-supply: Phandle to the external reference voltage supply. This should + only be set if there is an external reference voltage connected to the VREF + pin. If the property is not set the internal 2.5V reference is used. + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be + asserted during driver probe. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. + +AD5592R Example: + + #include <dt-bindings/iio/adi,ad5592r.h> + + vref: regulator-vref { + compatible = "regulator-fixed"; + regulator-name = "vref-ad559x"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ad5592r@0 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5592r"; + reg = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + vref-supply = <&vref>; /* optional */ + reset-gpios = <&gpio0 86 0>; /* optional */ + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + }; + channel@3 { + reg = <3>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@4 { + reg = <4>; + adi,mode = <CH_MODE_UNUSED>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@5 { + reg = <5>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@7 { + reg = <7>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; + +AD5593R Example: + + #include <dt-bindings/iio/adi,ad5592r.h> + + ad5593r@10 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5593r"; + reg = <0x10>; + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5755.txt b/Documentation/devicetree/bindings/iio/dac/ad5755.txt new file mode 100644 index 000000000000..f0bbd7e1029b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5755.txt @@ -0,0 +1,124 @@ +* Analog Device AD5755 IIO Multi-Channel DAC Linux Driver + +Required properties: + - compatible: Has to contain one of the following: + adi,ad5755 + adi,ad5755-1 + adi,ad5757 + adi,ad5735 + adi,ad5737 + + - reg: spi chip select number for the device + - spi-cpha or spi-cpol: is the only modes that is supported + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +See include/dt-bindings/iio/ad5755.h + - adi,ext-dc-dc-compenstation-resistor: boolean set if the hardware have an + external resistor and thereby bypasses + the internal compensation resistor. + - adi,dc-dc-phase: + Valid values for DC DC Phase control is: + 0: All dc-to-dc converters clock on the same edge. + 1: Channel A and Channel B clock on the same edge, + Channel C and Channel D clock on opposite edges. + 2: Channel A and Channel C clock on the same edge, + Channel B and Channel D clock on opposite edges. + 3: Channel A, Channel B, Channel C, and Channel D + clock 90 degrees out of phase from each other. + - adi,dc-dc-freq-hz: + Valid values for DC DC frequency is [Hz]: + 250000 + 410000 + 650000 + - adi,dc-dc-max-microvolt: + Valid values for the maximum allowed Vboost voltage supplied by + the dc-to-dc converter is: + 23000000 + 24500000 + 27000000 + 29500000 + +Optional for every channel: + - adi,mode: + Valid values for DAC modes is: + 0: 0 V to 5 V voltage range. + 1: 0 V to 10 V voltage range. + 2: Plus minus 5 V voltage range. + 3: Plus minus 10 V voltage range. + 4: 4 mA to 20 mA current range. + 5: 0 mA to 20 mA current range. + 6: 0 mA to 24 mA current range. + - adi,ext-current-sense-resistor: boolean set if the hardware a external + current sense resistor. + - adi,enable-voltage-overrange: boolean enable voltage overrange + - adi,slew: Array of slewrate settings should contain 3 fields: + 1: Should be either 0 or 1 in order to enable or disable slewrate. + 2: Slew rate settings: + Valid values for the slew rate update frequency: + 64000 + 32000 + 16000 + 8000 + 4000 + 2000 + 1000 + 500 + 250 + 125 + 64 + 32 + 16 + 8 + 4 + 0 + 3: Slew step size: + Valid values for the step size LSBs: + 1 + 2 + 4 + 16 + 32 + 64 + 128 + 256 + +Example: +dac@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "adi,ad5755"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + adi,dc-dc-phase = <0>; + adi,dc-dc-freq-hz = <410000>; + adi,dc-dc-max-microvolt = <23000000>; + channel@0 { + reg = <0>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@1 { + reg = <1>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@2 { + reg = <2>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@3 { + reg = <3>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt new file mode 100644 index 000000000000..7d6647d4af5e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt @@ -0,0 +1,20 @@ +NXP LPC1850 DAC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-dac" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: +dac: dac@400e1000 { + compatible = "nxp,lpc1850-dac"; + reg = <0x400e1000 0x1000>; + interrupts = <0>; + clocks = <&ccu1 CLK_APB3_DAC>; + vref-supply = <®_vdda>; + resets = <&rgu 42>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index e4d8f1c52f4a..a9fc11e43b45 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -8,10 +8,23 @@ Required properties: - interrupt-parent : should be the phandle for the interrupt controller - interrupts : interrupt mapping for GPIO IRQ +Optional properties: + - mount-matrix: an optional 3x3 mounting rotation matrix + + Example: mpu6050@68 { compatible = "invensense,mpu6050"; reg = <0x68>; interrupt-parent = <&gpio1>; interrupts = <18 1>; + mount-matrix = "-0.984807753012208", /* x0 */ + "0", /* y0 */ + "-0.173648177666930", /* z0 */ + "0", /* x1 */ + "-1", /* y1 */ + "0", /* z1 */ + "-0.173648177666930", /* x2 */ + "0", /* y2 */ + "0.984807753012208"; /* z2 */ }; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt new file mode 100644 index 000000000000..77d5aba1bd8c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt @@ -0,0 +1,29 @@ +* Asahi Kasei AK8974 magnetometer sensor + +Required properties: + +- compatible : should be "asahi-kasei,ak8974" +- reg : the I2C address of the magnetometer + +Optional properties: + +- avdd-supply: regulator supply for the analog voltage + (see regulator/regulator.txt) +- dvdd-supply: regulator supply for the digital voltage + (see regulator/regulator.txt) +- interrupts: data ready (DRDY) and interrupt (INT1) lines + from the chip, the DRDY interrupt must be placed first. + The interrupts can be triggered on rising or falling + edges alike. +- mount-matrix: an optional 3x3 mounting rotation matrix + +Example: + +ak8974@0f { + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&foo_reg>; + dvdd-supply = <&bar_reg>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>, + <1 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt index 011679f1a425..e1e7dd3259f6 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt @@ -8,6 +8,8 @@ Required properties: Optional properties: - gpios : should be device tree identifier of the magnetometer DRDY pin + - vdd-supply: an optional regulator that needs to be on to provide VDD + - mount-matrix: an optional 3x3 mounting rotation matrix Example: @@ -15,4 +17,14 @@ ak8975@0c { compatible = "asahi-kasei,ak8975"; reg = <0x0c>; gpios = <&gpj0 7 0>; + vdd-supply = <&ldo_3v3_gnss>; + mount-matrix = "-0.984807753012208", /* x0 */ + "0", /* y0 */ + "-0.173648177666930", /* z0 */ + "0", /* x1 */ + "-1", /* y1 */ + "0", /* z1 */ + "-0.173648177666930", /* x2 */ + "0", /* y2 */ + "0.984807753012208"; /* z2 */ }; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt b/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt new file mode 100644 index 000000000000..df77bf552656 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt @@ -0,0 +1,21 @@ +* Maxim Integrated DS1803 digital potentiometer driver + +The node for this driver must be a child node of a I2C controller, hence +all mandatory properties for your controller must be specified. See directory: + + Documentation/devicetree/bindings/i2c + +for more details. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "maxim,ds1803-010", + "maxim,ds1803-050", + "maxim,ds1803-100" + +Example: +ds1803: ds1803@1 { + reg = <0x28>; + compatible = "maxim,ds1803-010"; +}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt b/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt new file mode 100644 index 000000000000..3ccba16f7035 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt @@ -0,0 +1,84 @@ +* Microchip MCP413X/414X/415X/416X/423X/424X/425X/426X Digital Potentiometer + driver + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "microchip,mcp4131-502" + "microchip,mcp4131-103" + "microchip,mcp4131-503" + "microchip,mcp4131-104" + "microchip,mcp4132-502" + "microchip,mcp4132-103" + "microchip,mcp4132-503" + "microchip,mcp4132-104" + "microchip,mcp4141-502" + "microchip,mcp4141-103" + "microchip,mcp4141-503" + "microchip,mcp4141-104" + "microchip,mcp4142-502" + "microchip,mcp4142-103" + "microchip,mcp4142-503" + "microchip,mcp4142-104" + "microchip,mcp4151-502" + "microchip,mcp4151-103" + "microchip,mcp4151-503" + "microchip,mcp4151-104" + "microchip,mcp4152-502" + "microchip,mcp4152-103" + "microchip,mcp4152-503" + "microchip,mcp4152-104" + "microchip,mcp4161-502" + "microchip,mcp4161-103" + "microchip,mcp4161-503" + "microchip,mcp4161-104" + "microchip,mcp4162-502" + "microchip,mcp4162-103" + "microchip,mcp4162-503" + "microchip,mcp4162-104" + "microchip,mcp4231-502" + "microchip,mcp4231-103" + "microchip,mcp4231-503" + "microchip,mcp4231-104" + "microchip,mcp4232-502" + "microchip,mcp4232-103" + "microchip,mcp4232-503" + "microchip,mcp4232-104" + "microchip,mcp4241-502" + "microchip,mcp4241-103" + "microchip,mcp4241-503" + "microchip,mcp4241-104" + "microchip,mcp4242-502" + "microchip,mcp4242-103" + "microchip,mcp4242-503" + "microchip,mcp4242-104" + "microchip,mcp4251-502" + "microchip,mcp4251-103" + "microchip,mcp4251-503" + "microchip,mcp4251-104" + "microchip,mcp4252-502" + "microchip,mcp4252-103" + "microchip,mcp4252-503" + "microchip,mcp4252-104" + "microchip,mcp4261-502" + "microchip,mcp4261-103" + "microchip,mcp4261-503" + "microchip,mcp4261-104" + "microchip,mcp4262-502" + "microchip,mcp4262-103" + "microchip,mcp4262-503" + "microchip,mcp4262-104" + +Example: +mcp4131: mcp4131@0 { + compatible = "mcp4131-502"; + reg = <0>; + spi-max-frequency = <500000>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt index d7a6deb6b21e..c7198a03c906 100644 --- a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt +++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt @@ -1,7 +1,11 @@ -BMP085/BMP18x digital pressure sensors +BMP085/BMP18x/BMP28x digital pressure sensors Required properties: -- compatible: bosch,bmp085 +- compatible: must be one of: + "bosch,bmp085" + "bosch,bmp180" + "bosch,bmp280" + "bosch,bme280" Optional properties: - chip-id: configurable chip id for non-default chip revisions @@ -10,6 +14,10 @@ Optional properties: value range is 0-3 with rising sensitivity. - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ +- reset-gpios: a GPIO line handling reset of the sensor: as the line is + active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) +- vddd-supply: digital voltage regulator (see regulator/regulator.txt) +- vdda-supply: analog voltage regulator (see regulator/regulator.txt) Example: @@ -21,4 +29,7 @@ pressure@77 { default-oversampling = <2>; interrupt-parent = <&gpio0>; interrupts = <25 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + vddd-supply = <&foo>; + vdda-supply = <&bar>; }; diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt new file mode 100644 index 000000000000..54e7e70bcea5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/hp03.txt @@ -0,0 +1,17 @@ +HopeRF HP03 digital pressure/temperature sensors + +Required properties: +- compatible: must be "hoperf,hp03" +- xclr-gpio: must be device tree identifier of the XCLR pin. + The XCLR pin is a reset of the ADC in the chip, + it must be pulled HI before the conversion and + readout of the value from the ADC registers and + pulled LO afterward. + +Example: + +hp03@0x77 { + compatible = "hoperf,hp03"; + reg = <0x77>; + xclr-gpio = <&portc 0 0x0>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5611.txt b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt new file mode 100644 index 000000000000..17bca866c084 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt @@ -0,0 +1,19 @@ +MEAS ms5611 family pressure sensors + +Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces. + +Required properties: +- compatible: "meas,ms5611" or "meas,ms5607" +- reg: the I2C address or SPI chip select the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. + +Example: + +ms5607@77 { + compatible = "meas,ms5607"; + reg = <0x77>; + vdd-supply = <&ldo_3v3_gnss>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt new file mode 100644 index 000000000000..fb85de676e03 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt @@ -0,0 +1,31 @@ +Murata ZPA2326 pressure sensor + +Pressure sensor from Murata with SPI and I2C bus interfaces. + +Required properties: +- compatible: "murata,zpa2326" +- reg: the I2C address or SPI chip select the device will respond to + +Recommended properties for SPI bus usage: +- spi-max-frequency: maximum SPI bus frequency as documented in + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- vref-supply: an optional regulator that needs to be on to provide VREF + power to the sensor +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor +- interrupt-parent: phandle to the parent interrupt controller as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + +zpa2326@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + interrupt-parent = <&gpio>; + interrupts = <12>; + vdd-supply = <&ldo_1v8_gnss>; +}; diff --git a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt new file mode 100644 index 000000000000..b301dd2b35da --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt @@ -0,0 +1,24 @@ +Semtech's SX9500 capacitive proximity button device driver + +Required properties: + - compatible: must be "semtech,sx9500" + - reg: i2c address where to find the device + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - reset-gpios: Reference to the GPIO connected to the device's active + low reset pin. + +Example: + +sx9500@28 { + compatible = "semtech,sx9500"; + reg = <0x28>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index d4b87cc1e446..e41fe340162b 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -16,6 +16,10 @@ Optional properties: - st,drdy-int-pin: the pin on the package that will be used to signal "data ready" (valid values: 1 or 2). This property is not configurable on all sensors. +- drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share the same + interrupt line. (This binding is taken from pinctrl/pinctrl-bindings.txt) + This is a boolean property. Sensors may also have applicable pin control settings, those use the standard bindings from pinctrl/pinctrl-bindings.txt. @@ -37,6 +41,7 @@ Accelerometers: - st,lsm330-accel - st,lsm303agr-accel - st,lis2dh12-accel +- st,h3lis331dl-accel Gyroscopes: - st,l3g4200d-gyro @@ -46,6 +51,7 @@ Gyroscopes: - st,l3gd20-gyro - st,l3g4is-gyro - st,lsm330-gyro +- st,lsm9ds0-gyro Magnetometers: - st,lsm303agr-magn @@ -58,3 +64,4 @@ Pressure sensors: - st,lps001wp-press - st,lps25h-press - st,lps331ap-press +- st,lps22hb-press diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt new file mode 100644 index 000000000000..28bc5c4d965b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt @@ -0,0 +1,21 @@ +Maxim thermocouple support + +* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf +* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf + +Required properties: + + - compatible: must be "maxim,max31855" or "maxim,max6675" + - reg: SPI chip select number for the device + - spi-max-frequency: must be 4300000 + - spi-cpha: must be defined for max6675 to enable SPI mode 1 + + Refer to spi/spi-bus.txt for generic SPI slave bindings. + +Example: + + max31855@0 { + compatible = "maxim,max31855"; + reg = <0>; + spi-max-frequency = <4300000>; + }; diff --git a/Documentation/devicetree/bindings/input/adc-keys.txt b/Documentation/devicetree/bindings/input/adc-keys.txt new file mode 100644 index 000000000000..e551814629b4 --- /dev/null +++ b/Documentation/devicetree/bindings/input/adc-keys.txt @@ -0,0 +1,49 @@ +ADC attached resistor ladder buttons +------------------------------------ + +Required properties: + - compatible: "adc-keys" + - io-channels: Phandle to an ADC channel + - io-channel-names = "buttons"; + - keyup-threshold-microvolt: Voltage at which all the keys are considered up. + +Optional properties: + - poll-interval: Poll interval time in milliseconds + - autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem. + +Each button (key) is represented as a sub-node of "adc-keys": + +Required subnode-properties: + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + - press-threshold-microvolt: Voltage ADC input when this key is pressed. + +Example: + +#include <dt-bindings/input/input.h> + + adc-keys { + compatible = "adc-keys"; + io-channels = <&lradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <2000000>; + + button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <1500000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <1000000>; + }; + + button-enter { + label = "Enter"; + linux,code = <KEY_ENTER>; + press-threshold-microvolt = <500000>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt index c6cfe2e3ed41..9fc47b006fd1 100644 --- a/Documentation/devicetree/bindings/input/ads7846.txt +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -29,7 +29,7 @@ Optional properties: ti,vref-delay-usecs vref supply delay in usecs, 0 for external vref (u16). ti,vref-mv The VREF voltage, in millivolts (u16). - Set to 0 to use internal refernce + Set to 0 to use internal references (ADS7846). ti,keep-vref-on set to keep vref on for differential measurements as well diff --git a/Documentation/devicetree/bindings/input/atmel,captouch.txt b/Documentation/devicetree/bindings/input/atmel,captouch.txt new file mode 100644 index 000000000000..fe9ee5c53bcc --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,captouch.txt @@ -0,0 +1,36 @@ +Device tree bindings for Atmel capacitive touch device, typically +an Atmel touch sensor connected to AtmegaXX MCU running firmware +based on Qtouch library. + +The node for this device must be a child of a I2C controller node, as the +device communicates via I2C. + +Required properties: + + compatible: Must be "atmel,captouch". + reg: The I2C slave address of the device. + interrupts: Property describing the interrupt line the device + is connected to. The device only has one interrupt + source. + linux,keycodes: Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 8 entries. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + +Example: + + atmel-captouch@51 { + compatible = "atmel,captouch"; + reg = <0x51>; + interrupt-parent = <&tlmm>; + interrupts = <67 IRQ_TYPE_EDGE_FALLING>; + linux,keycodes = <BTN_0>, <BTN_1>, + <BTN_2>, <BTN_3>, + <BTN_4>, <BTN_5>, + <BTN_6>, <BTN_7>; + autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt index e68d2bbc6c07..3eed8819d05d 100644 --- a/Documentation/devicetree/bindings/input/clps711x-keypad.txt +++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X matrix keypad device tree bindings Required Properties: -- compatible: Shall contain "cirrus,clps711x-keypad". +- compatible: Shall contain "cirrus,ep7209-keypad". - row-gpios: List of GPIOs used as row lines. - poll-interval: Poll interval time in milliseconds. - linux,keymap: The definition can be found at @@ -12,7 +12,7 @@ Optional Properties: Example: keypad { - compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad"; + compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad"; autorepeat; poll-interval = <120>; row-gpios = <&porta 0 0>, diff --git a/Documentation/devicetree/bindings/input/gpio-decoder.txt b/Documentation/devicetree/bindings/input/gpio-decoder.txt new file mode 100644 index 000000000000..14a77fb96cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-decoder.txt @@ -0,0 +1,23 @@ +* GPIO Decoder DT bindings + +Required Properties: +- compatible: should be "gpio-decoder" +- gpios: a spec of gpios (at least two) to be decoded to a number with + first entry representing the MSB. + +Optional Properties: +- decoder-max-value: Maximum possible value that can be reported by + the gpios. +- linux,axis: the input subsystem axis to map to (ABS_X/ABS_Y). + Defaults to 0 (ABS_X). + +Example: + gpio-decoder0 { + compatible = "gpio-decoder"; + gpios = <&pca9536 3 GPIO_ACTIVE_HIGH>, + <&pca9536 2 GPIO_ACTIVE_HIGH>, + <&pca9536 1 GPIO_ACTIVE_HIGH>, + <&pca9536 0 GPIO_ACTIVE_HIGH>; + linux,axis = <0>; /* ABS_X */ + decoder-max-value = <9>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt index 95d0fb11a787..4d9a3717eaaf 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt @@ -34,11 +34,10 @@ Example nodes: gpio_keys_polled { compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; poll-interval = <100>; autorepeat; - button@21 { + + button21 { label = "GPIO Key UP"; linux,code = <103>; gpios = <&gpio1 0 1>; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 21641236c095..a94940481e55 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -32,17 +32,17 @@ Optional subnode-properties: Example nodes: - gpio_keys { + gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; autorepeat; - button@21 { + + up { label = "GPIO Key UP"; linux,code = <103>; gpios = <&gpio1 0 1>; }; - button@22 { + + down { label = "GPIO Key DOWN"; linux,code = <108>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; diff --git a/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt new file mode 100644 index 000000000000..5b6232db7c61 --- /dev/null +++ b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt @@ -0,0 +1,20 @@ +Raydium I2C touchscreen + +Required properties: +- compatible: must be "raydium,rm32380" +- reg: The I2C address of the device +- interrupt-parent: the phandle for the interrupt controller +- interrupts: interrupt to which the chip is connected + See ../interrupt-controller/interrupts.txt +Optional properties: +- avdd-supply: analog power supply needed to power device +- vccio-supply: IO Power source +- reset-gpios: reset gpio the chip is connected to. + +Example: + touchscreen@39 { + compatible = "raydium,rm32380"; + reg = <0x39>; + interrupt-parent = <&gpio>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt index 95fa715c6046..ec908b91fd90 100644 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt @@ -22,6 +22,15 @@ See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - syna,reset-delay-ms: The number of milliseconds to wait after resetting the device. +- syna,startup-delay-ms: The number of milliseconds to wait after powering on + the device. + +- vdd-supply: VDD power supply. +See ../regulator/regulator.txt + +- vio-supply: VIO power supply +See ../regulator/regulator.txt + Function Parameters: Parameters specific to RMI functions are contained in child nodes of the rmi device node. Documentation for the parameters of each function can be found in: diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt index 6c9f0c8a846c..e85ce3dea480 100644 --- a/Documentation/devicetree/bindings/input/rotary-encoder.txt +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -20,6 +20,8 @@ Optional properties: 2: Half-period mode 4: Quarter-period mode - wakeup-source: Boolean, rotary encoder can wake up the system. +- rotary-encoder,encoding: String, the method used to encode steps. + Supported are "gray" (the default and more common) and "binary". Deprecated properties: - rotary-encoder,half-period: Makes the driver work on half-period mode. @@ -34,6 +36,7 @@ Example: compatible = "rotary-encoder"; gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */ linux,axis = <0>; /* REL_X */ + rotary-encoder,encoding = "gray"; rotary-encoder,relative-axis; }; @@ -42,5 +45,6 @@ Example: gpios = <&gpio 21 0>, <&gpio 22 0>; linux,axis = <1>; /* ABS_Y */ rotary-encoder,steps = <24>; + rotary-encoder,encoding = "binary"; rotary-encoder,rollover; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt index 34e3382a0659..ac5dff412e25 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -2,11 +2,17 @@ Required properties: - compatible: must be "brcm,iproc-touchscreen" -- reg: physical base address of the controller and length of memory mapped - region. +- ts_syscon: handler of syscon node defining physical base + address of the controller and length of memory mapped region. + If this property is selected please make sure MFD_SYSCON config + is enabled in the defconfig file. - clocks: The clock provided by the SOC to driver the tsc -- clock-name: name for the clock +- clock-names: name for the clock - interrupts: The touchscreen controller's interrupt +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: Specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. Optional properties: - scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. @@ -53,13 +59,18 @@ Optional properties: - touchscreen-inverted-x: X axis is inverted (boolean) - touchscreen-inverted-y: Y axis is inverted (boolean) -Example: +Example: An example of touchscreen node - touchscreen: tsc@0x180A6000 { + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + touchscreen: touchscreen@180A6000 { compatible = "brcm,iproc-touchscreen"; #address-cells = <1>; #size-cells = <1>; - reg = <0x180A6000 0x40>; + ts_syscon = <&ts_adc_syscon>; clocks = <&adc_clk>; clock-names = "tsc_clk"; interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index f99528da1b1d..6db22103e2dd 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -19,6 +19,7 @@ Required properties: or: "edt,edt-ft5306" or: "edt,edt-ft5406" or: "edt,edt-ft5506" + or: "focaltech,ft6236" - reg: I2C slave address of the chip (0x38) - interrupt-parent: a phandle pointing to the interrupt controller @@ -43,6 +44,13 @@ Optional properties: - offset: allows setting the edge compensation in the range from 0 to 31. + - touchscreen-size-x : See touchscreen.txt + - touchscreen-size-y : See touchscreen.txt + - touchscreen-fuzz-x : See touchscreen.txt + - touchscreen-fuzz-y : See touchscreen.txt + - touchscreen-inverted-x : See touchscreen.txt + - touchscreen-inverted-y : See touchscreen.txt + - touchscreen-swapped-x-y : See touchscreen.txt Example: polytouch: edt-ft5x06@38 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt new file mode 100644 index 000000000000..5a19f4c3e9d7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt @@ -0,0 +1,27 @@ +* Elan eKTF2127 I2C touchscreen controller + +Required properties: + - compatible : "elan,ektf2127" + - reg : I2C slave address of the chip (0x40) + - interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts : interrupt specification for the ektf2127 interrupt + - power-gpios : GPIO specification for the pin connected to the + ektf2127's wake input. This needs to be driven high + to take ektf2127 out of it's low power state + +For additional optional properties see: touchscreen.txt + +Example: + +i2c@00000000 { + ektf2127: touchscreen@15 { + compatible = "elan,ektf2127"; + reg = <0x15>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt b/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt deleted file mode 100644 index 777521da3da5..000000000000 --- a/Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt +++ /dev/null @@ -1,35 +0,0 @@ -* FocalTech FT6236 I2C touchscreen controller - -Required properties: - - compatible : "focaltech,ft6236" - - reg : I2C slave address of the chip (0x38) - - interrupt-parent : a phandle pointing to the interrupt controller - serving the interrupt for this chip - - interrupts : interrupt specification for the touch controller - interrupt - - reset-gpios : GPIO specification for the RSTN input - - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) - - touchscreen-size-y : vertical resolution of touchscreen (in pixels) - -Optional properties: - - touchscreen-fuzz-x : horizontal noise value of the absolute input - device (in pixels) - - touchscreen-fuzz-y : vertical noise value of the absolute input - device (in pixels) - - touchscreen-inverted-x : X axis is inverted (boolean) - - touchscreen-inverted-y : Y axis is inverted (boolean) - - touchscreen-swapped-x-y: X and Y axis are swapped (boolean) - Swapping is done after inverting the axis - -Example: - - ft6x06@38 { - compatible = "focaltech,ft6236"; - reg = <0x38>; - interrupt-parent = <&gpio>; - interrupts = <23 2>; - touchscreen-size-x = <320>; - touchscreen-size-y = <480>; - touchscreen-inverted-x; - touchscreen-swapped-x-y; - }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt index cdf05f9b2329..abfcab3edc66 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -15,7 +15,7 @@ Optional properties: - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value between 1 and 4096. It is the ratio between the internal reference voltage - and the measured voltage after the plate was precharged. Resistence between + and the measured voltage after the plate was precharged. Resistance between plates and therefore the voltage decreases with pressure so that a smaller value is equivalent to a higher pressure. - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt new file mode 100644 index 000000000000..820fee4b77b6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -0,0 +1,37 @@ +* GSL 1680 touchscreen controller + +Required properties: +- compatible : "silead,gsl1680" +- reg : I2C slave address of the chip (0x40) +- interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip +- interrupts : interrupt specification for the gsl1680 interrupt +- power-gpios : Specification for the pin connected to the gsl1680's + shutdown input. This needs to be driven high to take the + gsl1680 out of its low power state +- touchscreen-size-x : See touchscreen.txt +- touchscreen-size-y : See touchscreen.txt + +Optional properties: +- firmware-name : File basename (string) for board specific firmware +- touchscreen-inverted-x : See touchscreen.txt +- touchscreen-inverted-y : See touchscreen.txt +- touchscreen-swapped-x-y : See touchscreen.txt +- silead,max-fingers : maximum number of fingers the touchscreen can detect + +Example: + +i2c@00000000 { + gsl1680: touchscreen@40 { + compatible = "silead,gsl1680"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + silead,max-fingers = <5>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt new file mode 100644 index 000000000000..d87ad14f1efe --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt @@ -0,0 +1,33 @@ +* SiS I2C Multiple Touch Controller + +Required properties: +- compatible: must be "sis,9200-ts" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller + (see interrupt binding [0]) +- interrupts: touch controller interrupt (see interrupt + binding [0]) + +Optional properties: +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the + device (see pinctrl binding [1]). +- attn-gpios: the gpio pin used as attention line +- reset-gpios: the gpio pin used to reset the controller +- wakeup-source: touchscreen can be used as a wakeup source + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + + sis9255@5c { + compatible = "sis,9200-ts"; + reg = <0x5c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sis>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; + irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt index e30e0b93f2b3..3e5b9793341f 100644 --- a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -1,13 +1,24 @@ -Texas Instruments TPS65218 power button +Texas Instruments TPS65217 and TPS65218 power button + +This module is part of the TPS65217/TPS65218. For more details about the whole +TPS65217 chip see Documentation/devicetree/bindings/regulator/tps65217.txt. This driver provides a simple power button event via an Interrupt. Required properties: -- compatible: should be "ti,tps65218-pwrbutton" +- compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton" + +Required properties for TPS65218: - interrupts: should be one of the following - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 -Example: +Examples: + +&tps { + tps65217-pwrbutton { + compatible = "ti,tps65217-pwrbutton"; + }; +}; &tps { power-button { diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 793c20ff8fcc..5393e2a45a42 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -21,6 +21,7 @@ Main node required properties: "arm,pl390" "arm,tc11mp-gic" "brcm,brahma-b15-gic" + "nvidia,tegra210-agic" "qcom,msm-8660-qgic" "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller @@ -68,7 +69,7 @@ Optional "ic_clk" (for "arm,arm11mp-gic") "PERIPHCLKEN" (for "arm,cortex-a15-gic") "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") - "clk" (for "arm,gic-400") + "clk" (for "arm,gic-400" and "nvidia,tegra210") "gclk" (for "arm,pl390") - power-domains : A phandle and PM domain specifier as defined by bindings of diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt index c9cf605bb995..2a1d16bdf834 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt @@ -6,7 +6,7 @@ controllers are OR:ed together and fed to the CPU tile's IRQ input. Each instance can handle up to 32 interrupts. Required properties: -- compatible: "arm,versatile-fpga-irq" +- compatible: "arm,versatile-fpga-irq" or "oxsemi,ox810se-rps-irq" - interrupt-controller: Identifies the node as an interrupt controller - #interrupt-cells: The number of cells to define the interrupts. Must be 1 as the FPGA IRQ controller has no configuration options for interrupt diff --git a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt new file mode 100644 index 000000000000..6c6e85324b9d --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt @@ -0,0 +1,22 @@ +Aspeed Vectored Interrupt Controller + +These bindings are for the Aspeed AST2400 interrupt controller register layout. +The SoC has an legacy register layout, but this driver does not support that +mode of operation. + +Required properties: + +- compatible : should be "aspeed,ast2400-vic". + +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +Example: + + vic: interrupt-controller@1e6c0080 { + compatible = "aspeed,ast2400-vic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1e6c0080 0x80>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt index 2d6c8bb4d827..6428a6ba9f4a 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -71,8 +71,8 @@ Bank 1: 24: DMA8 25: DMA9 26: DMA10 -27: DMA11 -28: DMA12 +27: DMA11-14 - shared interrupt for DMA 11 to 14 +28: DMAALL - triggers on all dma interrupts (including chanel 15) 29: AUX 30: ARM 31: VPUDMA diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt new file mode 100644 index 000000000000..4040905388d9 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt @@ -0,0 +1,57 @@ +Broadcom BCM6345-style Level 1 interrupt controller + +This block is a first level interrupt controller that is typically connected +directly to one of the HW INT lines on each CPU. + +Key elements of the hardware design include: + +- 32, 64 or 128 incoming level IRQ lines + +- Most onchip peripherals are wired directly to an L1 input + +- A separate instance of the register set for each CPU, allowing individual + peripheral IRQs to be routed to any CPU + +- Contains one or more enable/status word pairs per CPU + +- No atomic set/clear operations + +- No polarity/level/edge settings + +- No FIFO or priority encoder logic; software is expected to read all + 2-4 status words to determine which IRQs are pending + +Required properties: + +- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc" +- reg: specifies the base physical address and size of the registers; + the number of supported IRQs is inferred from the size argument +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller(s) + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node; valid values depend on the type of parent interrupt controller + +If multiple reg ranges and interrupt-parent entries are present on an SMP +system, the driver will allow IRQ SMP affinity to be set up through the +/proc/irq/ interface. In the simplest possible configuration, only one +reg range and one interrupt-parent is needed. + +The driver operates in native CPU endian by default, there is no support for +specifying an alternative endianness. + +Example: + +periph_intc: interrupt-controller@10000000 { + compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc"; + reg = <0x10000020 0x20>, + <0x10000040 0x20>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>, <3>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt index 759339c34e4f..969b4582ec60 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt @@ -2,7 +2,7 @@ Cirrus Logic CLPS711X Interrupt Controller Required properties: -- compatible: Should be "cirrus,clps711x-intc". +- compatible: Should be "cirrus,ep7209-intc". - reg: Specifies base physical address of the registers set. - interrupt-controller: Identifies the node as an interrupt controller. - #interrupt-cells: Specifies the number of cells needed to encode an @@ -34,7 +34,7 @@ ID Name Description Example: intc: interrupt-controller { - compatible = "cirrus,clps711x-intc"; + compatible = "cirrus,ep7312-intc", "cirrus,ep7209-intc"; reg = <0x80000000 0x4000>; interrupt-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt new file mode 100644 index 000000000000..888b2b9f7064 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt @@ -0,0 +1,17 @@ +EZchip NPS Interrupt Controller + +Required properties: + +- compatible : should be "ezchip,nps400-ic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + + +Example: + +intc: interrupt-controller { + compatible = "ezchip,nps400-ic"; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt b/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt new file mode 100644 index 000000000000..ee2ad36f8df8 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt @@ -0,0 +1,26 @@ +J-Core Advanced Interrupt Controller + +Required properties: + +- compatible: Should be "jcore,aic1" for the (obsolete) first-generation aic + with 8 interrupt lines with programmable priorities, or "jcore,aic2" for + the "aic2" core with 64 interrupts. + +- reg: Memory region(s) for configuration. For SMP, there should be one + region per cpu, indexed by the sequential, zero-based hardware cpu + number. + +- interrupt-controller: Identifies the node as an interrupt controller + +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + + +Example: + +aic: interrupt-controller@200 { + compatible = "jcore,aic2"; + reg = < 0x200 0x30 0x500 0x30 >; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt new file mode 100644 index 000000000000..86a7b4cd03f5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt @@ -0,0 +1,25 @@ +Marvell Armada 7K/8K PIC Interrupt controller +--------------------------------------------- + +This is the Device Tree binding for the PIC, a secondary interrupt +controller available on the Marvell Armada 7K/8K ARM64 SoCs, and +typically connected to the GIC as the primary interrupt controller. + +Required properties: +- compatible: should be "marvell,armada-8k-pic" +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: the number of cells to define interrupts on this + controller. Should be 1 +- reg: the register area for the PIC interrupt controller +- interrupts: the interrupt to the primary interrupt controller, + typically the GIC + +Example: + + pic: interrupt-controller@3f0100 { + compatible = "marvell,armada-8k-pic"; + reg = <0x3f0100 0x10>; + #interrupt-cells = <1>; + interrupt-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt index 8af0a8e613ab..3f6442c7f867 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -31,7 +31,7 @@ Required properties: Example: odmi: odmi@300000 { - compatible = "marvell,ap806-odm-controller", + compatible = "marvell,ap806-odmi-controller", "marvell,odmi-controller"; interrupt-controller; msi-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index b8e1674c7837..9d1d72c65489 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -9,6 +9,7 @@ Required properties: "mediatek,mt8135-sysirq" "mediatek,mt8127-sysirq" "mediatek,mt6795-sysirq" + "mediatek,mt6755-sysirq" "mediatek,mt6592-sysirq" "mediatek,mt6589-sysirq" "mediatek,mt6582-sysirq" @@ -16,8 +17,7 @@ Required properties: "mediatek,mt6577-sysirq" "mediatek,mt2701-sysirq" - interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Use the same format as specified by GIC in - Documentation/devicetree/bindings/arm/gic.txt +- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt. - interrupt-parent: phandle of irq parent for sysirq. The parent must use the same interrupt-cells format as GIC. - reg: Physical base address of the intpol registers and length of memory diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt index 1099fe0788fa..1099fe0788fa 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt b/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt index 539adca19e8f..38211f344dc8 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt @@ -1,38 +1,60 @@ -* NXP LPC32xx Main Interrupt Controller - (MIC, including SIC1 and SIC2 secondary controllers) +* NXP LPC32xx MIC, SIC1 and SIC2 Interrupt Controllers Required properties: -- compatible: Should be "nxp,lpc3220-mic" -- interrupt-controller: Identifies the node as an interrupt controller. -- interrupt-parent: Empty for the interrupt controller itself -- #interrupt-cells: The number of cells to define the interrupts. Should be 2. - The first cell is the IRQ number - The second cell is used to specify mode: - 1 = low-to-high edge triggered - 2 = high-to-low edge triggered - 4 = active high level-sensitive - 8 = active low level-sensitive - Default for internal sources should be set to 4 (active high). -- reg: Should contain MIC registers location and length +- compatible: "nxp,lpc3220-mic" or "nxp,lpc3220-sic". +- reg: should contain IC registers location and length. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: the number of cells to define an interrupt, should be 2. + The first cell is the IRQ number, the second cell is used to specify + one of the supported IRQ types: + IRQ_TYPE_EDGE_RISING = low-to-high edge triggered, + IRQ_TYPE_EDGE_FALLING = high-to-low edge triggered, + IRQ_TYPE_LEVEL_HIGH = active high level-sensitive, + IRQ_TYPE_LEVEL_LOW = active low level-sensitive. + Reset value is IRQ_TYPE_LEVEL_LOW. + +Optional properties: +- interrupt-parent: empty for MIC interrupt controller, link to parent + MIC interrupt controller for SIC1 and SIC2 +- interrupts: empty for MIC interrupt controller, cascaded MIC + hardware interrupts for SIC1 and SIC2 Examples: - /* - * MIC - */ + + /* LPC32xx MIC, SIC1 and SIC2 interrupt controllers */ mic: interrupt-controller@40008000 { compatible = "nxp,lpc3220-mic"; + reg = <0x40008000 0x4000>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + sic1: interrupt-controller@4000c000 { + compatible = "nxp,lpc3220-sic"; + reg = <0x4000c000 0x4000>; interrupt-controller; - interrupt-parent; #interrupt-cells = <2>; - reg = <0x40008000 0xC000>; + + interrupt-parent = <&mic>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>, + <30 IRQ_TYPE_LEVEL_LOW>; }; - /* - * ADC - */ + sic2: interrupt-controller@40010000 { + compatible = "nxp,lpc3220-sic"; + reg = <0x40010000 0x4000>; + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&mic>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + }; + + /* ADC */ adc@40048000 { compatible = "nxp,lpc3220-adc"; reg = <0x40048000 0x1000>; - interrupt-parent = <&mic>; - interrupts = <39 4>; + interrupt-parent = <&sic1>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index ae5054c27c99..e3f052d8c11a 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -1,10 +1,12 @@ -DT bindings for the R-Mobile/R-Car interrupt controller +DT bindings for the R-Mobile/R-Car/RZ/G interrupt controller Required properties: - compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. Examples with soctypes are: - "renesas,irqc-r8a73a4" (R-Mobile APE6) + - "renesas,irqc-r8a7743" (RZ/G1M) + - "renesas,irqc-r8a7745" (RZ/G1E) - "renesas,irqc-r8a7790" (R-Car H2) - "renesas,irqc-r8a7791" (R-Car M2-W) - "renesas,irqc-r8a7792" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt new file mode 100644 index 000000000000..6e7703d4ff5b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -0,0 +1,20 @@ +STM32 External Interrupt Controller + +Required properties: + +- compatible: Should be "st,stm32-exti" +- reg: Specifies base physical address and size of the registers +- interrupt-controller: Indentifies the node as an interrupt controller +- #interrupt-cells: Specifies the number of cells to encode an interrupt + specifier, shall be 2 +- interrupts: interrupts references to primary interrupt controller + +Example: + +exti: interrupt-controller@40013c00 { + compatible = "st,stm32-exti"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x40013C00 0x400>; + interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu index 43effa0a4fe7..18d4f407bf0e 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu @@ -4,7 +4,7 @@ All TI OMAP4/5 (and their derivatives) an interrupt controller that routes interrupts to the GIC, and also serves as a wakeup source. It is also referred to as "WUGEN-MPU", hence the name of the binding. -Reguired properties: +Required properties: - compatible : should contain at least "ti,omap4-wugen-mpu" or "ti,omap5-wugen-mpu" @@ -20,7 +20,7 @@ Notes: - Because this HW ultimately routes interrupts to the GIC, the interrupt specifier must be that of the GIC. - Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs - are explicitly forbiden. + are explicitly forbidden. Example: diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index 947863acc2d4..7b94c88cf2ee 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -1,6 +1,6 @@ * ARM SMMUv3 Architecture Implementation -The SMMUv3 architecture is a significant deparature from previous +The SMMUv3 architecture is a significant departure from previous revisions, replacing the MMIO register interface with in-memory command and event queues and adding support for the ATS and PRI components of the PCIe specification. diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index 718074501fcb..19fe6f2c83f6 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -16,6 +16,7 @@ conditions. "arm,mmu-400" "arm,mmu-401" "arm,mmu-500" + "cavium,smmu-v2" depending on the particular implementation and/or the version of the architecture implemented. diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index cd1b1cd7b5c4..53c20cae309f 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -1,7 +1,9 @@ * Mediatek IOMMU Architecture Implementation - Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which -uses the ARM Short-Descriptor translation table format for address translation. + Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and +this M4U have two generations of HW architecture. Generation one uses flat +pagetable, and only supports 4K size page mapping. Generation two uses the +ARM Short-Descriptor translation table format for address translation. About the M4U Hardware Block Diagram, please check below: @@ -36,7 +38,9 @@ in each larb. Take a example, There are many ports like MC, PP, VLD in the video decode local arbiter, all these ports are according to the video HW. Required properties: -- compatible : must be "mediatek,mt8173-m4u". +- compatible : must be one of the following string: + "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW. + "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. - clocks : must contain one entry for each clock-names. @@ -46,7 +50,8 @@ Required properties: according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in - dt-binding/memory/mt8173-larb-port.h. + dt-binding/memory/mt2701-larb-port.h for mt2701 and + dt-binding/memory/mt8173-larb-port.h for mt8173 Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt new file mode 100644 index 000000000000..20236385f26e --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt @@ -0,0 +1,64 @@ +* QCOM IOMMU + +The MSM IOMMU is an implementation compatible with the ARM VMSA short +descriptor page tables. It provides address translation for bus masters outside +of the CPU, each connected to the IOMMU through a port called micro-TLB. + +Required Properties: + + - compatible: Must contain "qcom,apq8064-iommu". + - reg: Base address and size of the IOMMU registers. + - interrupts: Specifiers for the MMU fault interrupts. For instances that + support secure mode two interrupts must be specified, for non-secure and + secure mode, in that order. For instances that don't support secure mode a + single interrupt must be specified. + - #iommu-cells: The number of cells needed to specify the stream id. This + is always 1. + - qcom,ncb: The total number of context banks in the IOMMU. + - clocks : List of clocks to be used during SMMU register access. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + for information about the format. For each clock specified + here, there must be a corresponding entry in clock-names + (see below). + + - clock-names : List of clock names corresponding to the clocks specified in + the "clocks" property (above). + Should be "smmu_pclk" for specifying the interface clock + required for iommu's register accesses. + Should be "smmu_clk" for specifying the functional clock + required by iommu for bus accesses. + +Each bus master connected to an IOMMU must reference the IOMMU in its device +node with the following property: + + - iommus: A reference to the IOMMU in multiple cells. The first cell is a + phandle to the IOMMU and the second cell is the stream id. + A single master device can be connected to more than one iommu + and multiple contexts in each of the iommu. So multiple entries + are required to list all the iommus and the stream ids that the + master is connected to. + +Example: mdp iommu and its bus master + + mdp_port0: iommu@7500000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "smmu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07500000 0x100000>; + interrupts = + <GIC_SPI 63 0>, + <GIC_SPI 64 0>; + qcom,ncb = <2>; + }; + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + ... + iommus = <&mdp_port0 0 + &mdp_port0 2>; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/lp855x.txt b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt index 0a3ecbc3a1b9..88f56641fc28 100644 --- a/Documentation/devicetree/bindings/leds/backlight/lp855x.txt +++ b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt @@ -13,6 +13,7 @@ Optional properties: - rom-addr: Register address of ROM area to be updated (u8) - rom-val: Register value to be updated (u8) - power-supply: Regulator which controls the 3V rail + - enable-supply: Regulator which controls the EN/VDDIO input Example: @@ -57,6 +58,7 @@ Example: backlight@2c { compatible = "ti,lp8557"; reg = <0x2c>; + enable-supply = <&backlight_vddio>; power-supply = <&backlight_vdd>; dev-ctrl = /bits/ 8 <0x41>; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index af10678ea2f6..696be5792625 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -19,6 +19,13 @@ Optional properties for child nodes: a device, i.e. no other LED class device can be assigned the same label. +- default-state : The initial state of the LED. Valid values are "on", "off", + and "keep". If the LED is already on or off and the default-state property is + set the to same value, then no glitch should be produced where the LED + momentarily turns off (or on). The "keep" setting will keep the LED at + whatever its current state is, without producing a glitch. The default is + off if this property is not present. + - linux,default-trigger : This parameter, if present, is a string defining the trigger assigned to the LED. Current triggers are: "backlight" - LED will act as a back-light, controlled by the framebuffer @@ -26,7 +33,9 @@ Optional properties for child nodes: "default-on" - LED will turn on (but for leds-gpio see "default-state" property in Documentation/devicetree/bindings/gpio/led.txt) "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity + "disk-activity" - LED indicates disk activity + "ide-disk" - LED indicates IDE disk activity (deprecated), + in new implementations use "disk-activity" "timer" - LED flashes at a fixed, configurable rate - led-max-microamp : Maximum LED supply current in microamperes. This property diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index 3f48c1eaf085..ccebce597f37 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -49,7 +49,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt index b22a55bcc65d..da5708e7b43b 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt @@ -28,7 +28,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index cbbeb1850910..76535ca37120 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -14,13 +14,8 @@ LED sub-node properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED. + see Documentation/devicetree/bindings/leds/common.txt - retain-state-suspended: (optional) The suspend state can be retained.Such as charge-led gpio. - panic-indicator : (optional) @@ -33,9 +28,9 @@ Examples: leds { compatible = "gpio-leds"; hdd { - label = "IDE Activity"; + label = "Disk Activity"; gpios = <&mcu_pio 0 GPIO_ACTIVE_LOW>; - linux,default-trigger = "ide-disk"; + linux,default-trigger = "disk-activity"; }; fault { diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt new file mode 100644 index 000000000000..fc2603484544 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt @@ -0,0 +1,59 @@ +LEDs connected to is31fl319x LED controller chip + +Required properties: +- compatible : Should be any of + "issi,is31fl3190" + "issi,is31fl3191" + "issi,is31fl3193" + "issi,is31fl3196" + "issi,is31fl3199" + "si-en,sn3199". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: 0x64, 0x65, 0x66, or 0x67. + +Optional properties: +- audio-gain-db : audio gain selection for external analog modulation input. + Valid values: 0 - 21, step by 3 (rounded down) + Default: 0 + +Each led is represented as a sub-node of the issi,is31fl319x device. +There can be less leds subnodes than the chip can support but not more. + +Required led sub-node properties: +- reg : number of LED line + Valid values: 1 - number of leds supported by the chip variant. + +Optional led sub-node properties: +- label : see Documentation/devicetree/bindings/leds/common.txt. +- linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt. +- led-max-microamp : (optional) + Valid values: 5000 - 40000, step by 5000 (rounded down) + Default: 20000 (20 mA) + Note: a driver will take the lowest of all led limits since the + chip has a single global setting. The lowest value will be chosen + due to the PWM specificity, where lower brightness is achieved + by reducing the dury-cycle of pulses and not the current, which + will always have its peak value equal to led-max-microamp. + +Examples: + +fancy_leds: leds@65 { + compatible = "issi,is31fl3196"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x65>; + + red_aux: led@1 { + label = "red:aux"; + reg = <1>; + led-max-microamp = <10000>; + }; + + green_power: led@5 { + label = "green:power"; + reg = <5>; + linux,default-trigger = "default-on"; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-pca9532.txt b/Documentation/devicetree/bindings/leds/leds-pca9532.txt new file mode 100644 index 000000000000..198f3ba0e01f --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pca9532.txt @@ -0,0 +1,39 @@ +*NXP - pca9532 PWM LED Driver + +The PCA9532 family is SMBus I/O expander optimized for dimming LEDs. +The PWM support 256 steps. + +Required properties: + - compatible: + "nxp,pca9530" + "nxp,pca9531" + "nxp,pca9532" + "nxp,pca9533" + - reg - I2C slave address + +Each led is represented as a sub-node of the nxp,pca9530. + +Optional sub-node properties: + - label: see Documentation/devicetree/bindings/leds/common.txt + - type: Output configuration, see dt-bindings/leds/leds-pca9532.h (default NONE) + - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: + #include <dt-bindings/leds/leds-pca9532.h> + + leds: pca9530@60 { + compatible = "nxp,pca9530"; + reg = <0x60>; + + red-power { + label = "pca:red:power"; + type = <PCA9532_TYPE_LED>; + }; + green-power { + label = "pca:green:power"; + type = <PCA9532_TYPE_LED>; + }; + }; + +For more product information please see the link below: +http://nxp.com/documents/data_sheet/PCA9532.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-pm8058.txt b/Documentation/devicetree/bindings/leds/leds-pm8058.txt new file mode 100644 index 000000000000..89584c49aab2 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pm8058.txt @@ -0,0 +1,67 @@ +Qualcomm PM8058 LED driver + +The Qualcomm PM8058 is a multi-functional device which contains +an LED driver block for up to six LEDs: three normal LEDs, two +"flash" LEDs and one "keypad backlight" LED. The names are +quoted because sometimes these LED drivers are used for wildly +different things than flash or keypad backlight: their names +are more of a suggestion than a hard-wired usecase. + +Hardware-wise the different LEDs support slightly different +output currents. The "flash" LEDs do not need to charge nor +do they support external triggers. They are just powerful LED +drivers. + +The LEDs appear as children to the PM8058 device, with the +proper compatible string. For the PM8058 bindings see: +mfd/qcom-pm8xxx.txt. + +Each LED is represented as a sub-node of the syscon device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: + +Required properties: +- compatible: one of + "qcom,pm8058-led" (for the normal LEDs at 0x131, 0x132 and 0x133) + "qcom,pm8058-keypad-led" (for the "keypad" LED at 0x48) + "qcom,pm8058-flash-led" (for the "flash" LEDs at 0x49 and 0xFB) + +Optional properties: +- label: see Documentation/devicetree/bindings/leds/common.txt +- default-state: see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: + +qcom,ssbi@500000 { + pmicintc: pmic@0 { + compatible = "qcom,pm8058"; + led@48 { + compatible = "qcom,pm8058-keypad-led"; + reg = <0x48>; + label = "pm8050:white:keypad"; + default-state = "off"; + }; + led@131 { + compatible = "qcom,pm8058-led"; + reg = <0x131>; + label = "pm8058:red"; + default-state = "off"; + }; + led@132 { + compatible = "qcom,pm8058-led"; + reg = <0x132>; + label = "pm8058:yellow"; + default-state = "off"; + linux,default-trigger = "mmc0"; + }; + led@133 { + compatible = "qcom,pm8058-led"; + reg = <0x133>; + label = "pm8058:green"; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt index 379cefdc0bda..59b56365f648 100644 --- a/Documentation/devicetree/bindings/leds/register-bit-led.txt +++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt @@ -23,13 +23,8 @@ Optional properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED + see Documentation/devicetree/bindings/leds/common.txt Example: diff --git a/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt new file mode 100644 index 000000000000..411ccf421584 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt @@ -0,0 +1,23 @@ +The PDC driver manages data transfer to and from various offload engines +on some Broadcom SoCs. An SoC may have multiple PDC hardware blocks. There is +one device tree entry per block. + +Required properties: +- compatible : Should be "brcm,iproc-pdc-mbox". +- reg: Should contain PDC registers location and length. +- interrupts: Should contain the IRQ line for the PDC. +- #mbox-cells: 1 +- brcm,rx-status-len: Length of metadata preceding received frames, in bytes. + +Optional properties: +- brcm,use-bcm-hdr: present if a BCM header precedes each frame. + +Example: + pdc0: iproc-pdc0@0x612c0000 { + compatible = "brcm,iproc-pdc-mbox"; + reg = <0 0x612c0000 0 0x445>; /* PDC FS0 regs */ + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; /* one cell per mailbox channel */ + brcm,rx-status-len = <32>; + brcm,use-bcm-hdr; + }; diff --git a/Documentation/devicetree/bindings/mailbox/meson-mhu.txt b/Documentation/devicetree/bindings/mailbox/meson-mhu.txt new file mode 100644 index 000000000000..a530310772b9 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/meson-mhu.txt @@ -0,0 +1,34 @@ +Amlogic Meson MHU Mailbox Driver +================================ + +The Amlogic's Meson SoCs Message-Handling-Unit (MHU) is a mailbox controller +that has 3 independent channels/links to communicate with remote processor(s). +MHU links are hardwired on a platform. A link raises interrupt for any +received data. However, there is no specified way of knowing if the sent +data has been read by the remote. This driver assumes the sender polls +STAT register and the remote clears it after having read the data. + +Mailbox Device Node: +==================== + +Required properties: +-------------------- +- compatible: Shall be "amlogic,meson-gxbb-mhu" +- reg: Contains the mailbox register address range (base + address and length) +- #mbox-cells Shall be 1 - the index of the channel needed. +- interrupts: Contains the interrupt information corresponding to + each of the 2 links of MHU. + +Example: +-------- + + mailbox: mailbox@c883c404 { + #mbox-cells = <1>; + compatible = "amlogic,meson-gxbb-mhu"; + reg = <0 0xc883c404 0 0x4c>; + interrupts = <0 208 IRQ_TYPE_EDGE_RISING>, + <0 209 IRQ_TYPE_EDGE_RISING>, + <0 210 IRQ_TYPE_EDGE_RISING>; + #mbox-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt new file mode 100644 index 000000000000..0d501154dfb2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt @@ -0,0 +1,29 @@ +* Analog Devices ADV7180 analog video decoder family + +The adv7180 family devices are used to capture analog video to different +digital interfaces like MIPI CSI-2 or parallel video. + +Required Properties : +- compatible : value must be one of + "adi,adv7180" + "adi,adv7182" + "adi,adv7280" + "adi,adv7280-m" + "adi,adv7281" + "adi,adv7281-m" + "adi,adv7281-ma" + "adi,adv7282" + "adi,adv7282-m" + +Example: + + i2c0@1c22000 { + ... + ... + adv7180@21 { + compatible = "adi,adv7180"; + reg = <0x21>; + }; + ... + }; + diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt new file mode 100644 index 000000000000..59a47a5b924b --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -0,0 +1,59 @@ +Mediatek Video Codec + +Mediatek Video Codec is the video codec hw present in Mediatek SoCs which +supports high resolution encoding functionalities. + +Required properties: +- compatible : "mediatek,mt8173-vcodec-enc" for encoder +- reg : Physical base address of the video codec registers and length of + memory mapped region. +- interrupts : interrupt number to the cpu. +- mediatek,larb : must contain the local arbiters in the current Socs. +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property. +- clock-names: encoder must contain "venc_sel_src", "venc_sel", +- "venc_lt_sel_src", "venc_lt_sel". +- iommus : should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,vpu : the node of video processor unit + +Example: +vcodec_enc: vcodec@0x18002000 { + compatible = "mediatek,mt8173-vcodec-enc"; + reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ + <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb3>, + <&larb5>; + iommus = <&iommu M4U_PORT_VENC_RCPU>, + <&iommu M4U_PORT_VENC_REC>, + <&iommu M4U_PORT_VENC_BSDMA>, + <&iommu M4U_PORT_VENC_SV_COMV>, + <&iommu M4U_PORT_VENC_RD_COMV>, + <&iommu M4U_PORT_VENC_CUR_LUMA>, + <&iommu M4U_PORT_VENC_CUR_CHROMA>, + <&iommu M4U_PORT_VENC_REF_LUMA>, + <&iommu M4U_PORT_VENC_REF_CHROMA>, + <&iommu M4U_PORT_VENC_NBM_RDMA>, + <&iommu M4U_PORT_VENC_NBM_WDMA>, + <&iommu M4U_PORT_VENC_RCPU_SET2>, + <&iommu M4U_PORT_VENC_REC_FRM_SET2>, + <&iommu M4U_PORT_VENC_BSDMA_SET2>, + <&iommu M4U_PORT_VENC_SV_COMA_SET2>, + <&iommu M4U_PORT_VENC_RD_COMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>, + <&iommu M4U_PORT_VENC_REF_LUMA_SET2>, + <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_UNIVPLL1_D2>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "venc_sel_src", + "venc_sel", + "venc_lt_sel_src", + "venc_lt_sel"; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vpu.txt b/Documentation/devicetree/bindings/media/mediatek-vpu.txt new file mode 100644 index 000000000000..2a5bac37f9a2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vpu.txt @@ -0,0 +1,31 @@ +* Mediatek Video Processor Unit + +Video Processor Unit is a HW video controller. It controls HW Codec including +H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color convert). + +Required properties: + - compatible: "mediatek,mt8173-vpu" + - reg: Must contain an entry for each entry in reg-names. + - reg-names: Must include the following entries: + "tcm": tcm base + "cfg_reg": Main configuration registers base + - interrupts: interrupt number to the cpu. + - clocks : clock name from clock manager + - clock-names: must be main. It is the main clock of VPU + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for VPU extended memory; if not present, VPU may be located + anywhere in the memory + +Example: + vpu: vpu@10020000 { + compatible = "mediatek,mt8173-vpu"; + reg = <0 0x10020000 0 0x30000>, + <0 0x10050000 0 0x100>; + reg-names = "tcm", "cfg_reg"; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen TOP_SCP_SEL>; + clock-names = "main"; + }; diff --git a/Documentation/devicetree/bindings/media/nokia,n900-ir b/Documentation/devicetree/bindings/media/nokia,n900-ir new file mode 100644 index 000000000000..13a18ce37dd1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nokia,n900-ir @@ -0,0 +1,20 @@ +Device-Tree bindings for LIRC TX driver for Nokia N900(RX51) + +Required properties: + - compatible: should be "nokia,n900-ir". + - pwms: specifies PWM used for IR signal transmission. + +Example node: + + pwm9: dmtimer-pwm@9 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer9>; + ti,clock-source = <0x00>; /* timer_sys_ck */ + #pwm-cells = <3>; + }; + + ir: n900-ir { + compatible = "nokia,n900-ir"; + + pwms = <&pwm9 0 26316 0>; /* 38000 Hz */ + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 619193ccf7ff..6a4e61cbe011 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -5,14 +5,22 @@ The rcar_vin device provides video input capabilities for the Renesas R-Car family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - - compatible: Must be one of the following + - compatible: Must be one or more of the following - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device + - "renesas,vin-r8a7792" for the R8A7792 device - "renesas,vin-r8a7791" for the R8A7791 device - "renesas,vin-r8a7790" for the R8A7790 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7778" for the R8A7778 device + - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 compatible device. + - "renesas,rcar-gen3-vin" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: the register base and size for the device registers - interrupts: the interrupt for the device - clocks: Reference to the parent clock @@ -37,7 +45,7 @@ Device node example }; vin0: vin@0xe6ef0000 { - compatible = "renesas,vin-r8a7790"; + compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; clocks = <&mstp8_clks R8A7790_CLK_VIN0>; reg = <0 0xe6ef0000 0 0x1000>; interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt new file mode 100644 index 000000000000..6a12960609d8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -0,0 +1,32 @@ +Renesas R-Car Frame Compression Processor (FCP) +----------------------------------------------- + +The FCP is a companion module of video processing modules in the Renesas R-Car +Gen3 SoCs. It provides data compression and decompression, data caching, and +conversion of AXI transactions in order to reduce the memory bandwidth. + +There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP +for FDP (FCPF). Their configuration and behaviour depend on the module they +are paired with. These DT bindings currently support the FCPV only. + + - compatible: Must be one or more of the following + + - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP' + - "renesas,fcpv" for generic compatible 'FCP for VSP' + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + + - reg: the register base and size for the device registers + - clocks: Reference to the functional clock + + +Device node example +------------------- + + fcpvd1: fcp@fea2f000 { + compatible = "renesas,r8a7795-fcpv", "renesas,fcpv"; + reg = <0 0xfea2f000 0 0x200>; + clocks = <&cpg CPG_MOD 602>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 627405abd144..9b695bcbf219 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -14,6 +14,11 @@ Required properties: - interrupts: VSP interrupt specifier. - clocks: A phandle + clock-specifier pair for the VSP functional clock. +Optional properties: + + - renesas,fcp: A phandle referencing the FCP that handles memory accesses + for the VSP. Not needed on Gen2, mandatory on Gen3. + Example: R8A7790 (R-Car H2) VSP1-S node diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt new file mode 100644 index 000000000000..925ab4d72eaa --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -0,0 +1,31 @@ +* Samsung HDMI CEC driver + +The HDMI CEC module is present is Samsung SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "samsung,s5p-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "hdmicec", + corresponding to entry in the clocks property. + - samsung,syscon-phandle - phandle to the PMU system controller + +Example: + +hdmicec: cec@100B0000 { + compatible = "samsung,s5p-cec"; + reg = <0x100B0000 0x200>; + interrupts = <0 114 0>; + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + samsung,syscon-phandle = <&pmu_system_controller>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 2d5787eac91a..92c94f5ecbf1 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -21,15 +21,18 @@ Required properties: - clock-names : from common clock binding: must contain "mfc", corresponding to entry in the clocks property. - - samsung,mfc-r : Base address of the first memory bank used by MFC - for DMA contiguous memory allocation and its size. - - - samsung,mfc-l : Base address of the second memory bank used by MFC - for DMA contiguous memory allocation and its size. - Optional properties: - power-domains : power-domain property defined with a phandle to respective power domain. + - memory-region : from reserved memory binding: phandles to two reserved + memory regions, first is for "left" mfc memory bus interfaces, + second if for the "right" mfc memory bus, used when no SYSMMU + support is available + +Obsolete properties: + - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region + property instead + Example: SoC specific DT entry: @@ -43,9 +46,29 @@ mfc: codec@13400000 { clock-names = "mfc"; }; +Reserved memory specific DT entry for given board (see reserved memory binding +for more information): + +reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mfc_left: region@51000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x51000000 0x800000>; + }; + + mfc_right: region@43000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x43000000 0x800000>; + }; +}; + Board specific DT entry: codec@13400000 { - samsung,mfc-r = <0x43000000 0x800000>; - samsung,mfc-l = <0x51000000 0x800000>; + memory-region = <&mfc_left>, <&mfc_right>; }; diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt index cbd46fa0988f..68ac210e688e 100644 --- a/Documentation/devicetree/bindings/media/xilinx/video.txt +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -20,7 +20,7 @@ The following properties are common to all Xilinx video IP cores. - xlnx,video-format: This property represents a video format transmitted on an AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream Video IP and System Design Guide" [UG934]. How the format relates to the IP - core is decribed in the IP core bindings documentation. + core is described in the IP core bindings documentation. - xlnx,video-width: This property qualifies the video format with the sample width expressed as a number of bits per pixel component. All components must diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt new file mode 100644 index 000000000000..9bb5f57e2066 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt @@ -0,0 +1,136 @@ +* Device tree bindings for Atmel EBI + +The External Bus Interface (EBI) controller is a bus where you can connect +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs). +The EBI provides a glue-less interface to asynchronous memories through the SMC +(Static Memory Controller). + +Required properties: + +- compatible: "atmel,at91sam9260-ebi" + "atmel,at91sam9261-ebi" + "atmel,at91sam9263-ebi0" + "atmel,at91sam9263-ebi1" + "atmel,at91sam9rl-ebi" + "atmel,at91sam9g45-ebi" + "atmel,at91sam9x5-ebi" + "atmel,sama5d3-ebi" + +- reg: Contains offset/length value for EBI memory mapping. + This property might contain several entries if the EBI + memory range is not contiguous + +- #address-cells: Must be 2. + The first cell encodes the CS. + The second cell encode the offset into the CS memory + range. + +- #size-cells: Must be set to 1. + +- ranges: Encodes CS to memory region association. + +- clocks: Clock feeding the EBI controller. + See clock-bindings.txt + +Children device nodes are representing device connected to the EBI bus. + +Required device node properties: + +- reg: Contains the chip-select id, the offset and the length + of the memory region requested by the device. + +EBI bus configuration will be defined directly in the device subnode. + +Optional EBI/SMC properties: + +- atmel,smc-bus-width: width of the asynchronous device's data bus + 8, 16 or 32. + Default to 8 when undefined. + +- atmel,smc-byte-access-type "write" or "select" (see Atmel datasheet). + Default to "select" when undefined. + +- atmel,smc-read-mode "nrd" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-write-mode "nwe" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-exnw-mode "disabled", "frozen" or "ready". + Default to "disabled" when undefined. + +- atmel,smc-page-mode enable page mode if present. The provided value + defines the page size (supported values: 4, 8, + 16 and 32). + +- atmel,smc-tdf-mode: "normal" or "optimized". When set to + "optimized" the data float time is optimized + depending on the next device being accessed + (next device setup time is subtracted to the + current device data float time). + Default to "normal" when undefined. + +If at least one atmel,smc- property is defined the following SMC timing +properties become mandatory. In the other hand, if none of the atmel,smc- +properties are specified, we assume that the EBI bus configuration will be +handled by the sub-device driver, and none of those properties should be +defined. + +All the timings are expressed in nanoseconds (see Atmel datasheet for a full +description). + +- atmel,smc-ncs-rd-setup-ns +- atmel,smc-nrd-setup-ns +- atmel,smc-ncs-wr-setup-ns +- atmel,smc-nwe-setup-ns +- atmel,smc-ncs-rd-pulse-ns +- atmel,smc-nrd-pulse-ns +- atmel,smc-ncs-wr-pulse-ns +- atmel,smc-nwe-pulse-ns +- atmel,smc-nwe-cycle-ns +- atmel,smc-nrd-cycle-ns +- atmel,smc-tdf-ns + +Example: + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + atmel,matrix = <&matrix>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ebi_addr>; + + nor: flash@0,0 { + compatible = "cfi-flash"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x1000000>; + bank-width = <2>; + + atmel,smc-read-mode = "nrd"; + atmel,smc-write-mode = "nwe"; + atmel,smc-bus-width = <16>; + atmel,smc-ncs-rd-setup-ns = <0>; + atmel,smc-ncs-wr-setup-ns = <0>; + atmel,smc-nwe-setup-ns = <8>; + atmel,smc-nrd-setup-ns = <16>; + atmel,smc-ncs-rd-pulse-ns = <84>; + atmel,smc-ncs-wr-pulse-ns = <84>; + atmel,smc-nrd-pulse-ns = <76>; + atmel,smc-nwe-pulse-ns = <76>; + atmel,smc-nrd-cycle-ns = <107>; + atmel,smc-nwe-cycle-ns = <84>; + atmel,smc-tdf-ns = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt new file mode 100644 index 000000000000..f633b5d0f8ca --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt @@ -0,0 +1,79 @@ +SAMSUNG Exynos SoCs SROM Controller driver. + +Required properties: +- compatible : Should contain "samsung,exynos4210-srom". + +- reg: offset and length of the register set + +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + <bank-number> 0 <parent address of bank> <size> + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, in addition to regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + +Example: basic definition, no banks are configured + memory-controller@12570000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/ddr.txt index f87856faf1ab..dde6d837083a 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/ddr.txt @@ -7,6 +7,8 @@ Properties: "fsl,qoriq-memory-controller". - reg : Address and size of DDR controller registers - interrupts : Error interrupt of DDR controller +- little-endian : Specifies little-endian access to registers + If omitted, big-endian will be used. Example 1: diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index 06a83ceebba7..aa614b2d7cab 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -2,16 +2,31 @@ SMI (Smart Multimedia Interface) Common The hardware block diagram please check bindings/iommu/mediatek,iommu.txt +Mediatek SMI have two generations of HW architecture, mt8173 uses the second +generation of SMI HW while mt2701 uses the first generation HW of SMI. + +There's slight differences between the two SMI, for generation 2, the +register which control the iommu port is at each larb's register base. But +for generation 1, the register is at smi ao base(smi always on register +base). Besides that, the smi async clock should be prepared and enabled for +SMI generation 1 to transform the smi clock into emi clock domain, but that is +not needed for SMI generation 2. + Required properties: -- compatible : must be "mediatek,mt8173-smi-common" +- compatible : must be one of : + "mediatek,mt2701-smi-common" + "mediatek,mt8173-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. - clocks : Must contain an entry for each entry in clock-names. -- clock-names : must contain 2 entries, as follows: +- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries + for generation 2 smi HW as follows: - "apb" : Advanced Peripheral Bus clock, It's the clock for setting the register. - "smi" : It's the clock for transfer data and command. - They may be the same if both source clocks are the same. + They may be the same if both source clocks are the same. + - "async" : asynchronous clock, it help transform the smi clock into the emi + clock domain, this clock is only needed by generation 1 smi HW. Example: smi_common: smi@14022000 { diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 55ff3b7e0bb9..21277a56e94c 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -3,7 +3,9 @@ SMI (Smart Multimedia Interface) Local Arbiter The hardware block diagram please check bindings/iommu/mediatek,iommu.txt Required properties: -- compatible : must be "mediatek,mt8173-smi-larb" +- compatible : must be one of : + "mediatek,mt8173-smi-larb" + "mediatek,mt2701-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. - power-domains : a phandle to the power domain of this local arbiter. diff --git a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt index b59c625d6336..ba0bc3f12419 100644 --- a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt @@ -190,7 +190,7 @@ be specified, according to the board documentation: Example SoC include file: / { - emc@0,7001b000 { + emc@7001b000 { compatible = "nvidia,tegra124-emc"; reg = <0x0 0x7001b000 0x0 0x1000>; @@ -201,7 +201,7 @@ Example SoC include file: Example board file: / { - emc@0,7001b000 { + emc@7001b000 { emc-timings-3 { nvidia,ram-code = <3>; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt index 3338a2834ad7..8dbe47013c2b 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt @@ -61,7 +61,7 @@ specified, according to the board documentation: Example SoC include file: / { - mc: memory-controller@0,70019000 { + mc: memory-controller@70019000 { compatible = "nvidia,tegra124-mc"; reg = <0x0 0x70019000 0x0 0x1000>; clocks = <&tegra_car TEGRA124_CLK_MC>; @@ -72,7 +72,7 @@ Example SoC include file: #iommu-cells = <1>; }; - sdhci@0,700b0000 { + sdhci@700b0000 { compatible = "nvidia,tegra124-sdhci"; ... iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; @@ -82,7 +82,7 @@ Example SoC include file: Example board file: / { - memory-controller@0,70019000 { + memory-controller@70019000 { emc-timings-3 { nvidia,ram-code = <3>; diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt index 01683707060b..c1359f4d48d7 100644 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt @@ -32,6 +32,23 @@ Required properties: bootloader) are used for the physical address decoding. As this will change in the future, filling correct values here is a requirement. + - interrupt-controller: The GPMC driver implements and interrupt controller for + the NAND events "fifoevent" and "termcount" plus the + rising/falling edges on the GPMC_WAIT pins. + The interrupt number mapping is as follows + 0 - NAND_fifoevent + 1 - NAND_termcount + 2 - GPMC_WAIT0 pin edge + 3 - GPMC_WAIT1 pin edge, and so on. + - interrupt-cells: Must be set to 2 + - gpio-controller: The GPMC driver implements a GPIO controller for the + GPMC WAIT pins that can be used as general purpose inputs. + 0 maps to GPMC_WAIT0 pin. + - gpio-cells: Must be set to 2 + +Required properties when using NAND prefetch dma: + - dmas GPMC NAND prefetch dma channel + - dma-names Must be set to "rxtx" Timing properties for child nodes. All are optional and default to 0. @@ -124,12 +141,17 @@ Example for an AM33xx board: ti,hwmods = "gpmc"; reg = <0x50000000 0x2000>; interrupts = <100>; - + dmas = <&edma 52 0>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <2>; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; /* child nodes go here */ }; diff --git a/Documentation/devicetree/bindings/mfd/ac100.txt b/Documentation/devicetree/bindings/mfd/ac100.txt new file mode 100644 index 000000000000..b8ef00667599 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ac100.txt @@ -0,0 +1,54 @@ +X-Powers AC100 Codec/RTC IC Device Tree bindings + +AC100 is a audio codec and RTC subsystem combo IC. The 2 parts are +separated, including power supplies and interrupt lines, but share +a common register address space and host interface. + +Required properties: +- compatible: "x-powers,ac100" +- reg: The I2C slave address or RSB hardware address for the chip +- sub-nodes: + - codec + - compatible: "x-powers,ac100-codec" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_AUDIO pin + - #clock-cells: Shall be 0 + - clock-output-names: "4M_adda" + + - see clock/clock-bindings.txt for common clock bindings + + - rtc + - compatible: "x-powers,ac100-rtc" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_RTC pin + - clocks: A phandle to the codec's "4M_adda" clock + - #clock-cells: Shall be 1 + - clock-output-names: "cko1_rtc", "cko2_rtc", "cko3_rtc" + + - see clock/clock-bindings.txt for common clock bindings + +Example: + +ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", "cko2_rtc", "cko3_rtc"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt index f71283055685..462819ac3da8 100644 --- a/Documentation/devicetree/bindings/mfd/act8945a.txt +++ b/Documentation/devicetree/bindings/mfd/act8945a.txt @@ -14,13 +14,6 @@ Example: reg = <0x5b>; status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_chglev>; - active-semi,chglev-gpio = <&pioA 12 GPIO_ACTIVE_HIGH>; - active-semi,input-voltage-threshold-microvolt = <6600>; - active-semi,precondition-timeout = <40>; - active-semi,total-timeout = <3>; - active-semi,vsel-high; regulators { @@ -73,4 +66,19 @@ Example: regulator-always-on; }; }; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + status = "okay"; + }; }; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 9b30011ecabe..8f2e2822238d 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -1,6 +1,6 @@ Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs -These devices are audio SoCs with extensive digital capabilites and a range +These devices are audio SoCs with extensive digital capabilities and a range of analogue I/O. Required properties: @@ -85,6 +85,24 @@ Optional properties: present, the number of values should be less than or equal to the number of inputs, unspecified inputs will use the chip default. + - wlf,max-channels-clocked : The maximum number of channels to be clocked on + each AIF, useful for I2S systems with multiple data lines being mastered. + Specify one cell for each AIF to be configured, specify zero for AIFs that + should be handled normally. + If present, number of cells must be less than or equal to the number of + AIFs. If less than the number of AIFs, for cells that have not been + specified the corresponding AIFs will be treated as default setting. + + - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + + - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt new file mode 100644 index 000000000000..4fc5b83726d6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt @@ -0,0 +1,18 @@ +The Aspeed System Control Unit manages the global behaviour of the SoC, +configuring elements such as clocks, pinmux, and reset. + +Required properties: +- compatible: One of: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + +- reg: contains the offset and length of the SCU memory region + +Example: + +syscon: syscon@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index fd39fa54571b..8f3ad9ab4637 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -6,10 +6,12 @@ axp202 (X-Powers) axp209 (X-Powers) axp221 (X-Powers) axp223 (X-Powers) +axp809 (X-Powers) Required properties: - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", - "x-powers,axp221", "x-powers,axp223" + "x-powers,axp221", "x-powers,axp223", "x-powers,axp806", + "x-powers,axp809" - reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin @@ -18,7 +20,14 @@ Required properties: Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz - (range: 750-1875). Default: 1.5MHz + AXP152/20X: range: 750-1875, Default: 1.5 MHz + AXP22X/80X: range: 1800-4050, Default: 3 MHz + +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not. + - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -39,7 +48,6 @@ Optional properties for DCDC regulators: probably makes sense for HiFi audio related applications that aren't battery constrained. - AXP202/AXP209 regulators, type, and corresponding input supply names: Regulator Type Supply Name Notes @@ -76,6 +84,55 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +AXP806 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDCA : DC-DC buck : vina-supply : poly-phase capable +DCDCB : DC-DC buck : vinb-supply : poly-phase capable +DCDCC : DC-DC buck : vinc-supply : poly-phase capable +DCDCD : DC-DC buck : vind-supply : poly-phase capable +DCDCE : DC-DC buck : vine-supply : poly-phase capable +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +BLDO1 : LDO : bldoin-supply : shared supply +BLDO2 : LDO : bldoin-supply : shared supply +BLDO3 : LDO : bldoin-supply : shared supply +BLDO4 : LDO : bldoin-supply : shared supply +CLDO1 : LDO : cldoin-supply : shared supply +CLDO2 : LDO : cldoin-supply : shared supply +CLDO3 : LDO : cldoin-supply : shared supply +SW : On/Off Switch : swin-supply + +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements +for higher output current. The possible groupings are: A+B, A+B+C, D+E. + +AXP809 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply Example: diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 1857f4a6b9a9..9554292dc6cb 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -8,10 +8,13 @@ Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: - buck0 : regulator BUCK0 - buck1 : regulator BUCK1 - buck2 : regulator BUCK2 - buck3 : regulator BUCK3 + buck1 : regulator BUCK CORE + buck2 : regulator BUCK PRO + buck3 : regulator BUCK MEM + buck4 : regulator BUCK PERI + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 ldo4 : regulator LDO4 ldo5 : regulator LDO5 ldo6 : regulator LDO6 @@ -19,9 +22,6 @@ Sub-nodes: ldo8 : regulator LDO8 ldo9 : regulator LDO9 ldo10 : regulator LDO10 - ldo11 : regulator LDO11 - ldo12 : regulator LDO12 - ldo13 : regulator LDO13 The bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */ reg = <0x48>; regulators { - buck0 { + buck1 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck1 { + buck2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck2 { + buck3 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; - buck3 { + buck4 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt new file mode 100644 index 000000000000..05485699d70e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -0,0 +1,27 @@ +Hisilicon Hi655x Power Management Integrated Circuit (PMIC) + +The hardware layout for access PMIC Hi655x from AP SoC Hi6220. +Between PMIC Hi655x and Hi6220, the physical signal channel is SSI. +We can use memory-mapped I/O to communicate. + ++----------------+ +-------------+ +| | | | +| Hi6220 | SSI bus | Hi655x | +| |-------------| | +| |(REGMAP_MMIO)| | ++----------------+ +-------------+ + +Required properties: +- compatible: Should be "hisilicon,hi655x-pmic". +- reg: Base address of PMIC on Hi6220 SoC. +- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). +- pmic-gpios: The GPIO used by PMIC IRQ. + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + } diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt new file mode 100644 index 000000000000..52766c2035f7 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt @@ -0,0 +1,59 @@ +TI LP873X PMIC MFD driver + +Required properties: + - compatible: "ti,lp8732", "ti,lp8733" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: List of child nodes that specify the regulator + initialization data. +Example: + +pmic: lp8733@60 { + compatible = "ti,lp8733"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + lp8733_buck0: buck0 { + regulator-name = "lp8733-buck0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-always-on; + regulator-boot-on; + }; + + lp8733_buck1: buck1 { + regulator-name = "lp8733-buck1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo0: ldo0 { + regulator-name = "lp8733-ldo0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo1: ldo1 { + regulator-name = "lp8733-ldo1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 000000000000..2ad44f7e4880 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,143 @@ +MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" + "maxim,max20024". +- reg: I2C device address. + +Optional properties: +------------------- +- interrupts: The interrupt on the parent the controller is + connected to. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: is <2> and their usage is compliant to the 2 cells + variant of <../interrupt-controller/interrupts.txt> + IRQ numbers for different interrupt source of MAX77620 + are defined at dt-bindings/mfd/max77620.h. + +Optional subnodes and their properties: +======================================= + +Flexible power sequence configurations: +-------------------------------------- +The Flexible Power Sequencer (FPS) allows each regulator to power up under +hardware or software control. Additionally, each regulator can power on +independently or among a group of other regulators with an adjustable power-up +and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed +to be part of a sequence allowing external regulators to be sequenced along +with internal regulators. 32KHz clock can be programmed to be part of a +sequence. + +The flexible sequencing structure consists of two hardware enable inputs +(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2. +Each master sequencing timer is programmable through its configuration +register to have a hardware enable source (EN1 or EN2) or a software enable +source (SW). When enabled/disabled, the master sequencing timer generates +eight sequencing events on different time periods called slots. The time +period between each event is programmable within the configuration register. +Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power +sequence slave register which allows its enable source to be specified as +a flexible power sequencer timer or a software bit. When a FPS source of +regulators, GPIOs and clocks specifies the enable source to be a flexible +power sequencer, the power up and power down delays can be specified in +the regulators, GPIOs and clocks flexible power sequencer configuration +registers. + +When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz +clock are set into following state at the sequencing event that +corresponds to its flexible sequencer configuration register. + Sleep state: In this state, regulators, GPIOs + and 32KHz clock get disabled at + the sequencing event. + Global Low Power Mode (GLPM): In this state, regulators are set in + low power mode at the sequencing event. + +The configuration parameters of FPS is provided through sub-node "fps" +and their child for FPS specific. The child node name for FPS are "fps0", +"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively. + +The FPS configurations like FPS source, power up and power down slots for +regulators, GPIOs and 32kHz clocks are provided in their respective +configuration nodes which is explained in respective sub-system DT +binding document. + +There is need for different FPS configuration parameters based on system +state like when system state changed from active to suspend or active to +power off (shutdown). + +Optional properties: +------------------- +-maxim,fps-event-source: u32, FPS event source like external + hardware input to PMIC i.e. EN0, EN1 or + software (SW). + The macros are defined on + dt-bindings/mfd/max77620.h + for different control source. + - MAX77620_FPS_EVENT_SRC_EN0 + for hardware input pin EN0. + - MAX77620_FPS_EVENT_SRC_EN1 + for hardware input pin EN1. + - MAX77620_FPS_EVENT_SRC_SW + for software control. + +-maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to shutdown + state. + +-maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to suspend state. + +-maxim,device-state-on-disabled-event: u32, describe the PMIC state when FPS + event cleared (set to LOW) whether it + should go to sleep state or low-power + state. Following are valid values: + - MAX77620_FPS_INACTIVE_STATE_SLEEP + to set the PMIC state to sleep. + - MAX77620_FPS_INACTIVE_STATE_LOW_POWER + to set the PMIC state to low + power. + Absence of this property or other value + will not change device state when FPS + event get cleared. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +For DT binding details of different sub modules like GPIO, pincontrol, +regulator, power, please refer respective device-tree binding document +under their respective sub-system directories. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> + +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + fps { + fps0 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + }; + + fps1 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + }; + + fps2 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index d3425846aa5b..6a1ae3a2b77f 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -17,28 +17,28 @@ Required properties: - interrupt-parent : The parent interrupt controller. Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnod +- regulators : The regulators of max77693 have to be instantiated under subnode named "regulators" using the following format. regulators { - regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constratints[*]. + regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constraints[*]. }; [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the approprite level of feedback. + order to provide the appropriate level of feedback. Required properties: - - compatible : Must be "maxim,max77693-hpatic" + - compatible : Must be "maxim,max77693-haptic" - haptic-supply : power supply for the haptic motor [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - pwms : phandle to the physical PWM(Pulse Width Modulation) device. PWM properties should be named "pwms". And number of cell is different for each pwm device. - To get more informations, please refer to documentaion. + To get more information, please refer to documentation. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - charger : Node configuring the charger driver. diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt index f24f33409164..37a088f9a648 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -62,6 +62,7 @@ The below bindings specify the set of valid subnodes. "qcom,pm8058-rtc" "qcom,pm8921-rtc" "qcom,pm8941-rtc" + "qcom,pm8018-rtc" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt index 5e97a9593ad7..485bc59fcc48 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -13,6 +13,7 @@ frequencies. "qcom,rpm-msm8660" "qcom,rpm-msm8960" "qcom,rpm-ipq8064" + "qcom,rpm-mdm9615" - reg: Usage: required @@ -59,6 +60,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8058-regulators" "qcom,rpm-pm8901-regulators" "qcom,rpm-pm8921-regulators" + "qcom,rpm-pm8018-regulators" - vdd_l0_l1_lvs-supply: - vdd_l2_l11_l12-supply: @@ -137,6 +139,15 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vin_lvs1-supply: +- vdd_l7-supply: +- vdd_l8-supply: +- vdd_l9_l10_l11_l12-supply: + Usage: optional (pm8018 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -156,6 +167,10 @@ pm8921: l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch, ncp +pm8018: + s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, + l12, l14, lvs1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt - with additional custom properties described below: @@ -178,7 +193,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional (default if no other qcom,force-mode is specified) Value type: <u32> - Defintion: indicates that the regulator should be forced to a + Definition: indicates that the regulator should be forced to a particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode @@ -204,7 +219,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional Value type: <u32> - Defintion: indicates that the regulator should not be forced to any + Definition: indicates that the regulator should not be forced to any particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 4ca6aab4273a..9636ae8d8d41 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -1,7 +1,11 @@ -RK808 Power Management Integrated Circuit +RK8XX Power Management Integrated Circuit + +The rk8xx family current members: +rk808 +rk818 Required properties: -- compatible: "rockchip,rk808" +- compatible: "rockchip,rk808", "rockchip,rk818" - reg: I2C slave address - interrupt-parent: The parent interrupt controller. - interrupts: the interrupt outputs of the controller. @@ -13,6 +17,8 @@ Optional properties: default output clock name - rockchip,system-power-controller: Telling whether or not this pmic is controlling the system power. + +Optional RK808 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 - vcc3-supply: The input supply for DCDC_REG3 @@ -29,7 +35,20 @@ Optional properties: the gpio controller. If DVS GPIOs aren't present, voltage changes will happen very quickly with no slow ramp time. -Regulators: All the regulators of RK808 to be instantiated shall be +Optional RK818 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- boost-supply: The input supply for DCDC_BOOST +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3, LDO_REG5 and LDO_REG7 +- vcc8-supply: The input supply for LDO_REG4, LDO_REG6 and LDO_REG8 +- vcc9-supply: The input supply for LDO_REG9 and SWITCH_REG +- h_5v-supply: The input supply for HDMI_SWITCH +- usb-supply: The input supply for OTG_SWITCH + +Regulators: All the regulators of RK8XX to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented by a child node of the 'regulators' node. @@ -48,6 +67,18 @@ number as described in RK808 datasheet. - SWITCH_REGn - valid values for n are 1 to 2 +Following regulators of the RK818 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK818 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 9. + - SWITCH_REG + - HDMI_SWITCH + - OTG_SWITCH + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 937785a3eddc..9e6770b105c9 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,18 +1,21 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618 is a power management IC family which integrates +3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and +a watchdog timer. The RN5T618 provides additionally a Li-ion battery +charger, fuel gauge and an ADC. It can be controlled through an I2C +interface. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt new file mode 100644 index 000000000000..c110e118b79f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt @@ -0,0 +1,70 @@ +Samsung Exynos SoC Low Power Audio Subsystem (LPASS) + +Required properties: + + - compatible : "samsung,exynos5433-lpass" + - reg : should contain the LPASS top SFR region location + and size + - samsung,pmu-syscon : the phandle to the Power Management Unit node + - #address-cells : should be 1 + - #size-cells : should be 1 + - ranges : must be present + +Each IP block of the Low Power Audio Subsystem should be specified as +an optional sub-node. For "samsung,exynos5433-lpass" compatible this includes: +UART, SLIMBUS, PCM, I2S, DMAC, Timers 0...4, VIC, WDT 0...1 devices. + +Bindings of the sub-nodes are described in: + ../serial/samsung_uart.txt + ../sound/samsung-i2s.txt + ../dma/arm-pl330.txt + + +Example: + +audio-subsystem { + compatible = "samsung,exynos5433-lpass"; + reg = <0x11400000 0x100>, <0x11500000 0x08>; + samsung,pmu-syscon = <&pmu_system_controller>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + adma: adma@11420000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x11420000 0x1000>; + interrupts = <0 73 0>; + clocks = <&cmu_aud CLK_ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; + }; + + i2s0: i2s0@11440000 { + compatible = "samsung,exynos7-i2s"; + reg = <0x11440000 0x100>; + dmas = <&adma 0 &adma 2>; + dma-names = "tx", "rx"; + interrupts = <0 70 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_I2S_BCLK>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; + status = "disabled"; + }; + + serial_3: serial@11460000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x11460000 0x100>; + interrupts = <0 67 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_UART>, + <&cmu_aud CLK_SCLK_AUD_UART>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart_aud_bus>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index 3fb68bfefc8b..f9065a5781a2 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,7 +4,7 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - reg : I2C/SPI address of the device Optional properties: diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index a41157b5d930..9a98ee7c323d 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -12,6 +12,7 @@ Required properties: - interrupt-parent: The parent interrupt controller - gpio-controller: - #gpio-cells = <1>: twl6040 provides GPO lines. +- #clock-cells = <0>; twl6040 is a provider of pdmclk which is used by McPDM - twl6040,audpwron-gpio: Power on GPIO line for the twl6040 - vio-supply: Regulator for the twl6040 VIO supply @@ -19,8 +20,8 @@ Required properties: Optional properties, nodes: - enable-active-high: To power on the twl6040 during boot. -- clocks: phandle to the clk32k clock provider -- clock-names: Must be "clk32k" +- clocks: phandle to the clk32k and/or to mclk clock provider +- clock-names: Must be "clk32k" for the 32K clock and "mclk" for the MCLK. Vibra functionality Required properties: diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt index 7bab90cc4a7b..4a7e030e4f9b 100644 --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -4,7 +4,8 @@ Required properties: - compatible: "brcm,bcm3384", "brcm,bcm33843" "brcm,bcm3384-viper", "brcm,bcm33843-viper" - "brcm,bcm6328", "brcm,bcm6368", + "brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6368", + "brcm,bcm63168", "brcm,bcm63268", "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu3.txt b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt new file mode 100644 index 000000000000..616862ad2b71 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit v3 + +Properties: +- compatible: "cavium,octeon-7890-ciu3" + + Compatibility with 78XX and 73XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is source number. + The second cell indicates the triggering semantics, and may have a + value of either 4 for level semantics, or 1 for edge semantics. + +Example: + interrupt-controller@1010000000000 { + compatible = "cavium,octeon-7890-ciu3"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Source number (20 significant bits) + * 2) Trigger type: (4 == level, 1 == edge) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10100 0x00000000 0x0 0xb0000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt index fc149f326dae..f080f06da6d8 100644 --- a/Documentation/devicetree/bindings/mips/cpu_irq.txt +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -13,7 +13,7 @@ Required properties: - compatible : Should be "mti,cpu-interrupt-controller" Example devicetree: - cpu-irq: cpu-irq@0 { + cpu-irq: cpu-irq { #address-cells = <0>; interrupt-controller; diff --git a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt index c7a26ca8da12..6611a7c2053a 100644 --- a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt +++ b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt @@ -30,11 +30,90 @@ Required properties: region may not be present in some scenarios, such as in the device tree presented to a virtual machine. + - msi-parent + Value type: <phandle> + Definition: Must be present and point to the MSI controller node + handling message interrupts for the MC. + + - ranges + Value type: <prop-encoded-array> + Definition: A standard property. Defines the mapping between the child + MC address space and the parent system address space. + + The MC address space is defined by 3 components: + <region type> <offset hi> <offset lo> + + Valid values for region type are + 0x0 - MC portals + 0x1 - QBMAN portals + + - #address-cells + Value type: <u32> + Definition: Must be 3. (see definition in 'ranges' property) + + - #size-cells + Value type: <u32> + Definition: Must be 1. + +Sub-nodes: + + The fsl-mc node may optionally have dpmac sub-nodes that describe + the relationship between the Ethernet MACs which belong to the MC + and the Ethernet PHYs on the system board. + + The dpmac nodes must be under a node named "dpmacs" which contains + the following properties: + + - #address-cells + Value type: <u32> + Definition: Must be present if dpmac sub-nodes are defined and must + have a value of 1. + + - #size-cells + Value type: <u32> + Definition: Must be present if dpmac sub-nodes are defined and must + have a value of 0. + + These nodes must have the following properties: + + - compatible + Value type: <string> + Definition: Must be "fsl,qoriq-mc-dpmac". + + - reg + Value type: <prop-encoded-array> + Definition: Specifies the id of the dpmac. + + - phy-handle + Value type: <phandle> + Definition: Specifies the phandle to the PHY device node associated + with the this dpmac. + Example: fsl_mc: fsl-mc@80c000000 { compatible = "fsl,qoriq-mc"; reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ - }; + msi-parent = <&its>; + #address-cells = <3>; + #size-cells = <1>; + + /* + * Region type 0x0 - MC portals + * Region type 0x1 - QBMAN portals + */ + ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000 + 0x1 0x0 0x0 0x8 0x18000000 0x8000000>; + dpmacs { + #address-cells = <1>; + #size-cells = <0>; + + dpmac@1 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <1>; + phy-handle = <&mdio0_phy0>; + } + } + }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 31b35c3a5e47..49df630bd44f 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -9,8 +9,12 @@ Device Tree Bindings for the Arasan SDHCI Controller [4] Documentation/devicetree/bindings/phy/phy-bindings.txt Required Properties: - - compatible: Compatibility string. Must be 'arasan,sdhci-8.9a' or - 'arasan,sdhci-4.9a' or 'arasan,sdhci-5.1' + - compatible: Compatibility string. One of: + - "arasan,sdhci-8.9a": generic Arasan SDHCI 8.9a PHY + - "arasan,sdhci-4.9a": generic Arasan SDHCI 4.9a PHY + - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY + - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY + For this device it is strongly suggested to include arasan,soc-ctl-syscon. - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" @@ -22,6 +26,20 @@ Required Properties for "arasan,sdhci-5.1": - phys: From PHY bindings: Phandle for the Generic PHY for arasan. - phy-names: MUST be "phy_arasan". +Optional Properties: + - arasan,soc-ctl-syscon: A phandle to a syscon device (see ../mfd/syscon.txt) + used to access core corecfg registers. Offsets of registers in this + syscon are determined based on the main compatible string for the device. + - clock-output-names: If specified, this will be the name of the card clock + which will be exposed by this device. Required if #clock-cells is + specified. + - #clock-cells: If specified this should be the value <0>. With this property + in place we will export a clock representing the Card Clock. This clock + is expected to be consumed by our PHY. You must also specify + - xlnx,fails-without-test-cd: when present, the controller doesn't work when + the CD line is not connected properly, and the line is not connected + properly. Test mode can be used to force the controller to function. + Example: sdhci@e0100000 { compatible = "arasan,sdhci-8.9a"; @@ -42,3 +60,19 @@ Example: phys = <&emmc_phy>; phy-names = "phy_arasan"; } ; + + sdhci: sdhci@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0x0 0xfe330000 0x0 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + arasan,soc-ctl-syscon = <&grf>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clock-output-names = "emmc_cardclock"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + #clock-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt deleted file mode 100644 index 59476fbdbfa1..000000000000 --- a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt +++ /dev/null @@ -1,18 +0,0 @@ -Broadcom BCM2835 SDHCI controller - -This file documents differences between the core properties described -by mmc.txt and the properties that represent the BCM2835 controller. - -Required properties: -- compatible : Should be "brcm,bcm2835-sdhci". -- clocks : The clock feeding the SDHCI controller. - -Example: - -sdhci: sdhci { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clk_mmc>; - bus-width = <4>; -}; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.txt new file mode 100644 index 000000000000..733b64a4d8eb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.txt @@ -0,0 +1,38 @@ +* BROADCOM BRCMSTB/BMIPS SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-brcmstb driver. + +NOTE: The driver disables all UHS speed modes by default and depends +on Device Tree properties to enable them for SoC/Board combinations +that support them. + +Required properties: +- compatible: should be one of the following + - "brcm,bcm7425-sdhci" + - "brcm,bcm7445-sdhci" + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + + sdhci@f03e0100 { + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0000 0x100>; + interrupts = <0x0 0x26 0x0>; + sdhci,auto-cmd12; + clocks = <&sw_sdio>; + sd-uhs-sdr50; + sd-uhs-ddr50; + }; + + sdhci@f03e0300 { + non-removable; + bus-width = <0x8>; + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0200 0x100>; + interrupts = <0x0 0x27 0x0>; + sdhci,auto-cmd12; + clocks = <sw_sdio>; + mmc-hs200-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index dca56d6248f5..3e29050ec769 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -28,6 +28,8 @@ Optional properties: transparent level shifters on the outputs of the controller. Two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. +- fsl,tuning-start-tap: Specify the start dealy cell point when send first CMD19 + in tuning procedure. - fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure. The uSDHC use one delay cell as default increasing step to do tuning process. This property allows user to change the tuning step to more than one delay diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt index 71ad57e050b1..3149297b3933 100644 --- a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -20,7 +20,7 @@ Example: compatible = "microchip,pic32mzda-sdhci"; reg = <0x1f8ec000 0x100>; interrupts = <191 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&REFCLKO4>, <&PBCLK5>; + clocks = <&rootclk REF4CLK>, <&rootclk PB5CLK>; clock-names = "base_clk", "sys_clk"; bus-width = <4>; cap-sd-highspeed; diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt index 0cb827bf9435..3d965d57e00b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt @@ -1,7 +1,7 @@ * The simple eMMC hardware reset provider The purpose of this driver is to perform standard eMMC hw reset -procedure, as descibed by Jedec 4.4 specification. This procedure is +procedure, as described by Jedec 4.4 specification. This procedure is performed just after MMC core enabled power to the given mmc host (to fix possible issues if bootloader has left eMMC card in initialized or unknown state), and before performing complete system reboot (also in diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt index ce0e76749671..e25436861867 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt @@ -16,6 +16,8 @@ Optional properties: See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entry: "ext_clock" (External clock provided to the card). +- post-power-on-delay-ms : Delay in ms after powering the card and + de-asserting the reset-gpios (if any) Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index ed23b9bedfdc..8a377827695b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -46,8 +46,12 @@ Optional properties: - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported +- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported - dsr: Value the card's (optional) Driver Stage Register (DSR) should be programmed with. Valid range: [0 .. 0xffff]. +- no-sdio: controller is limited to send sdio cmd during initialization +- no-sd: controller is limited to send sd cmd during initialization +- no-mmc: controller is limited to send mmc cmd during initialization *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" @@ -71,6 +75,17 @@ Optional SDIO properties: - wakeup-source: Enables wake up of host system on SDIO IRQ assertion (Legacy property supported: "enable-sdio-wakeup") +MMC power +--------- + +Controllers may implement power control from both the connected cards and +the IO signaling (for example to change to high-speed 1.8V signalling). If +the system supports this, then the following two properties should point +to valid regulator nodes: + +- vqmmc-supply: supply node for IO line power +- vmmc-supply: supply node for card's power + MMC power sequences: -------------------- @@ -98,11 +113,13 @@ Required host node properties when using function subnodes: - #size-cells: should be zero. Required function subnode properties: -- compatible: name of SDIO function following generic names recommended practice - reg: Must contain the SDIO function number of the function this subnode describes. A value of 0 denotes the memory SD function, values from 1 to 7 denote the SDIO functions. +Optional function subnode properties: +- compatible: name of SDIO function following generic names recommended practice + Examples -------- diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index ea5614b6f613..07184e8f894e 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -15,6 +15,7 @@ Required Properties: - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 + - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 Optional Properties: * clocks: from common clock binding: if ciu_drive and ciu_sample are diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 88faa91125bf..3cd4c43a3260 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -10,7 +10,7 @@ Required properties: subsystem (mmcss) inside the FlashSS (available in STiH407 SoC family). -- clock-names: Should be "mmc". +- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) See: Documentation/devicetree/bindings/resource-names.txt - clocks: Phandle to the clock. See: Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 4bf41d833804..55cdd804cdba 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -8,7 +8,12 @@ as the speed of SD standard 3.0. Absolute maximum transfer rate is 200MB/s Required properties: - - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc" + - compatible : should be one of: + * "allwinner,sun4i-a10-mmc" + * "allwinner,sun5i-a13-mmc" + * "allwinner,sun7i-a20-mmc" + * "allwinner,sun9i-a80-mmc" + * "allwinner,sun50i-a64-mmc" - reg : mmc controller base registers - clocks : a list with 4 phandle + clock specifier pairs - clock-names : must contain "ahb", "mmc", "output" and "sample" diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 8636f5ae97e5..4e00e859e885 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -39,6 +39,10 @@ Required Properties: Optional properties: +* resets: phandle + reset specifier pair, intended to represent hardware + reset signal present internally in some host controller IC designs. + See Documentation/devicetree/bindings/reset/reset.txt for details. + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 0f610d4b5b00..13df9c2399c3 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -23,6 +23,7 @@ Required properties: "renesas,sdhi-r8a7793" - SDHI IP on R8A7793 SoC "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC + "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt index beace4b89daa..4ec28796a3c0 100644 --- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt +++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt @@ -1,8 +1,26 @@ Flash device on ARM Versatile board +These flash chips are found in the ARM reference designs like Integrator, +Versatile, RealView, Versatile Express etc. + +They are regular CFI compatible (Intel or AMD extended) flash chips with +some special write protect/VPP bits that can be controlled by the machine's +system controller. + Required properties: -- compatible : must be "arm,versatile-flash"; +- compatible : must be "arm,versatile-flash", "cfi-flash"; +- reg : memory address for the flash chip - bank-width : width in bytes of flash interface. +For the rest of the properties, see mtd-physmap.txt. + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. + +Example: + +flash@34000000 { + compatible = "arm,versatile-flash", "cfi-flash"; + reg = <0x34000000 0x4000000>; + bank-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index d53aba98fbc9..3e7ee99d3949 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -39,7 +39,7 @@ Optional properties: Nand Flash Controller(NFC) is an optional sub-node Required properties: -- compatible : "atmel,sama5d3-nfc" or "atmel,sama5d4-nfc". +- compatible : "atmel,sama5d3-nfc". - reg : should specify the address and size used for NFC command registers, NFC registers and NFC SRAM. NFC SRAM address and size can be absent if don't want to use it. diff --git a/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt new file mode 100644 index 000000000000..489807005eda --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt @@ -0,0 +1,32 @@ +* Atmel Quad Serial Peripheral Interface (QSPI) + +Required properties: +- compatible: Should be "atmel,sama5d2-qspi". +- reg: Should contain the locations and lengths of the base registers + and the mapped memory. +- reg-names: Should contain the resource reg names: + - qspi_base: configuration register address space + - qspi_mmap: memory mapped address space +- interrupts: Should contain the interrupt for the device. +- clocks: The phandle of the clock needed by the QSPI controller. +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. + +Example: + +spi@f0020000 { + compatible = "atmel,sama5d2-qspi"; + reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; + reg-names = "qspi_base", "qspi_mmap"; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&spi0_clk>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; + status = "okay"; + + m25p80@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index c2546ced9c02..b40f3a492800 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -24,8 +24,10 @@ Required properties: brcm,brcmnand-v5.0 brcm,brcmnand-v6.0 brcm,brcmnand-v6.1 + brcm,brcmnand-v6.2 brcm,brcmnand-v7.0 brcm,brcmnand-v7.1 + brcm,brcmnand-v7.2 brcm,brcmnand - reg : the register start and length for NAND register region. (optional) Flash DMA register range (if present) @@ -52,7 +54,7 @@ Optional properties: v7.0. Use this property to describe the rare earlier versions of this core that include WP - -- Additonal SoC-specific NAND controller properties -- + -- Additional SoC-specific NAND controller properties -- The NAND controller is integrated differently on the variety of SoCs on which it is found. Part of this integration involves providing status and enable bits diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt new file mode 100644 index 000000000000..f248056da24c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -0,0 +1,56 @@ +* Cadence Quad SPI controller + +Required properties: +- compatible : Should be "cdns,qspi-nor". +- reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the QSPI Controller data area. +- interrupts : Unit interrupt specifier for the controller interrupt. +- clocks : phandle to the Quad SPI clock. +- cdns,fifo-depth : Size of the data FIFO in words. +- cdns,fifo-width : Bus width of the data FIFO in bytes. +- cdns,trigger-address : 32-bit indirect AHB trigger address. + +Optional properties: +- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. + +Optional subnodes: +Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional +custom properties: +- cdns,read-delay : Delay for read capture logic, in clock cycles +- cdns,tshsl-ns : Delay in nanoseconds for the length that the master + mode chip select outputs are de-asserted between + transactions. +- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being + de-activated and the activation of another. +- cdns,tchsh-ns : Delay in nanoseconds between last bit of current + transaction and deasserting the device chip select + (qspi_n_ss_out). +- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low + and first bit transfer. + +Example: + + qspi: spi@ff705000 { + compatible = "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff705000 0x1000>, + <0xffa00000 0x1000>; + interrupts = <0 151 4>; + clocks = <&qspi_clk>; + cdns,is-decoded-cs; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + + flash0: n25q00@0 { + ... + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 0333ec87dc49..c34aa6f8a424 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -5,7 +5,8 @@ Required properties: "fsl,imx7d-qspi", "fsl,imx6ul-qspi", "fsl,ls1021a-qspi" or - "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi" + "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi", + "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index fb733c4e1c11..174f68c26c1b 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -13,7 +13,11 @@ Documentation/devicetree/bindings/mtd/nand.txt Required properties: - - reg: The CS line the peripheral is connected to + - compatible: "ti,omap2-nand" + - reg: range id (CS number), base offset and length of the + NAND I/O space + - interrupt-parent: must point to gpmc node + - interrupts: Two interrupt specifiers, one for fifoevent, one for termcount. Optional properties: @@ -35,7 +39,7 @@ Optional properties: "prefetch-polled" Prefetch polled mode (default) "polled" Polled mode, without prefetch - "prefetch-dma" Prefetch enabled sDMA mode + "prefetch-dma" Prefetch enabled DMA mode "prefetch-irq" Prefetch enabled irq mode - elm_id: <deprecated> use "ti,elm-id" instead @@ -44,6 +48,7 @@ Optional properties: locating ECC errors for BCHx algorithms. SoC devices which have ELM hardware engines should specify this device node in .dtsi Using ELM for ECC error correction frees some CPU cycles. + - rb-gpios: GPIO specifier for the ready/busy# pin. For inline partition table parsing (optional): @@ -55,20 +60,26 @@ Example for an AM33xx board: gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; - reg = <0x50000000 0x1000000>; + reg = <0x50000000 0x36c>; interrupts = <100>; gpmc,num-cs = <8>; gpmc,num-waitpins = <2>; #address-cells = <2>; #size-cells = <1>; - ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + ranges = <0 0 0x08000000 0x1000000>; /* CS0 space, 16MB */ elm_id = <&elm>; + interrupt-controller; + #interrupt-cells = <2>; nand@0,0 { - reg = <0 0 0>; /* CS0, offset 0 */ + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* CS0, offset 0, NAND I/O window 4 */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>; nand-bus-width = <16>; ti,nand-ecc-opt = "bch8"; ti,nand-xfer-type = "polled"; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; diff --git a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt new file mode 100644 index 000000000000..74981520d6dd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt @@ -0,0 +1,24 @@ +HiSilicon SPI-NOR Flash Controller + +Required properties: +- compatible : Should be "hisilicon,fmc-spi-nor" and one of the following strings: + "hisilicon,hi3519-spi-nor" +- address-cells : Should be 1. +- size-cells : Should be 0. +- reg : Offset and length of the register set for the controller device. +- reg-names : Must include the following two entries: "control", "memory". +- clocks : handle to spi-nor flash controller clock. + +Example: +spi-nor-controller@10000000 { + compatible = "hisilicon,hi3519-spi-nor", "hisilicon,fmc-spi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000000 0x1000>, <0x14000000 0x1000000>; + reg-names = "control", "memory"; + clocks = <&clock HI3519_FMC_CLK>; + spi-nor@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt new file mode 100644 index 000000000000..069c192ed5c2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -0,0 +1,160 @@ +MTK SoCs NAND FLASH controller (NFC) DT binding + +This file documents the device tree bindings for MTK SoCs NAND controllers. +The functional split of the controller requires two drivers to operate: +the nand controller interface driver and the ECC engine driver. + +The hardware description for both devices must be captured as device +tree nodes. + +1) NFC NAND Controller Interface (NFI): +======================================= + +The first part of NFC is NAND Controller Interface (NFI) HW. +Required NFI properties: +- compatible: Should be "mediatek,mtxxxx-nfc". +- reg: Base physical address and size of NFI. +- interrupts: Interrupts of NFI. +- clocks: NFI required clocks. +- clock-names: NFI clocks internal name. +- status: Disabled default. Then set "okay" by platform. +- ecc-engine: Required ECC Engine node. +- #address-cells: NAND chip index, should be 1. +- #size-cells: Should be 0. + +Example: + + nandc: nfi@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + status = "disabled"; + ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + }; + +Platform related properties, should be set in {platform_name}.dts: +- children nodes: NAND chips. + +Children nodes properties: +- reg: Chip Select Signal, default 0. + Set as reg = <0>, <1> when need 2 CS. +Optional: +- nand-on-flash-bbt: Store BBT on NAND Flash. +- nand-ecc-mode: the NAND ecc mode (check driver for supported modes) +- nand-ecc-step-size: Number of data bytes covered by a single ECC step. + valid values: 512 and 1024. + 1024 is recommended for large page NANDs. +- nand-ecc-strength: Number of bits to correct per ECC step. + The valid values that the controller supports are: 4, 6, + 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44, + 48, 52, 56, 60. + The strength should be calculated as follows: + E = (S - F) * 8 / 14 + S = O / (P / Q) + E : nand-ecc-strength. + S : spare size per sector. + F : FDM size, should be in the range [1,8]. + It is used to store free oob data. + O : oob size. + P : page size. + Q : nand-ecc-step-size. + If the result does not match any one of the listed + choices above, please select the smaller valid value from + the list. + (otherwise the driver will do the adjustment at runtime) +- pinctrl-names: Default NAND pin GPIO setting name. +- pinctrl-0: GPIO setting node. + +Example: + &pio { + nand_pins_default: nanddefault { + pins_dat { + pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>, + <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>, + <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>, + <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>, + <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>, + <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>, + <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>, + <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>, + <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>; + input-enable; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up; + }; + + pins_we { + pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + + pins_ale { + pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + }; + }; + + &nandc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_default>; + nand@0 { + reg = <0>; + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + }; + }; + +NAND chip optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + preloader@0 { + label = "pl"; + read-only; + reg = <0x00000000 0x00400000>; + }; + android@0x00400000 { + label = "android"; + reg = <0x00400000 0x12c00000>; + }; + }; + }; + +2) ECC Engine: +============== + +Required BCH properties: +- compatible: Should be "mediatek,mtxxxx-ecc". +- reg: Base physical address and size of ECC. +- interrupts: Interrupts of ECC. +- clocks: ECC required clocks. +- clock-names: ECC clocks internal name. +- status: Disabled default. Then set "okay" by platform. + +Example: + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + clock-names = "nfiecc_clk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index b53f92e252d4..3733300de8dd 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -1,8 +1,31 @@ -* MTD generic binding +* NAND chip and NAND controller generic binding + +NAND controller/NAND chip representation: + +The NAND controller should be represented with its own DT node, and all +NAND chips attached to this controller should be defined as children nodes +of the NAND controller. This representation should be enforced even for +simple controllers supporting only one chip. + +Mandatory NAND controller properties: +- #address-cells: depends on your controller. Should at least be 1 to + encode the CS line id. +- #size-cells: depends on your controller. Put zero unless you need a + mapping between CS lines and dedicated memory regions + +Optional NAND controller properties +- ranges: only needed if you need to define a mapping between CS lines and + memory regions + +Optional NAND chip properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode. - Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", - "soft_bch". + Supported values are: "none", "soft", "hw", "hw_syndrome", + "hw_oob_first". + Deprecated values: + "soft_bch": use "soft" and nand-ecc-algo instead +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values are: "hamming", "bch". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -19,3 +42,20 @@ errors per {size} bytes". The interpretation of these parameters is implementation-defined, so not all implementations must support all possible combinations. However, implementations are encouraged to further specify the value(s) they support. + +Example: + + nand-controller { + #address-cells = <1>; + #size-cells = <0>; + + /* controller specific properties */ + + nand@0 { + reg = <0>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + + /* controller specific properties */ + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 086d6f44c4b9..f322f56aef74 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -11,10 +11,16 @@ Required properties: * "ahb" : AHB gating clock * "mod" : nand controller clock +Optional properties: +- dmas : shall reference DMA channel associated to the NAND controller. +- dma-names : shall be "rxtx". + Optional children nodes: Children nodes represent the available nand chips. Optional properties: +- reset : phandle + reset specifier pair +- reset-names : must contain "ahb" - allwinner,rb : shall contain the native Ready/Busy ids. or - rb-gpios : shall contain the gpios used as R/B pins. diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index 05f705e32a4a..f591ab782dbc 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -47,6 +47,9 @@ Optional properties: Valid values are between 0 to 7, that maps to 273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps Default value is 2, which corresponds to 899 ps +- rxlos-gpios: Input gpio from SFP+ module to indicate availability of + incoming signal. + Example: menetclk: menetclk { @@ -59,8 +62,8 @@ Example: compatible = "apm,xgene-enet"; status = "disabled"; reg = <0x0 0x17020000 0x0 0xd100>, - <0x0 0X17030000 0x0 0X400>, - <0x0 0X10000000 0x0 0X200>; + <0x0 0x17030000 0x0 0x400>, + <0x0 0x10000000 0x0 0x200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; interrupts = <0x0 0x3c 0x4>; port-id = <0>; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt new file mode 100644 index 000000000000..78722d74cea8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt @@ -0,0 +1,37 @@ +APM X-Gene SoC MDIO node + +MDIO node is defined to describe on-chip MDIO controller. + +Required properties: + - compatible: Must be "apm,xgene-mdio-rgmii" or "apm,xgene-mdio-xfi" + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + - reg: Address and length of the register set + - clocks: Reference to the clock entry + +For the phys on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Example: + + mdio: mdio@17020000 { + compatible = "apm,xgene-mdio-rgmii"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x17020000 0x0 0xd100>; + clocks = <&menetclk 0>; + }; + + /* Board-specific peripheral configurations */ + &mdio { + menetphy: phy@3 { + reg = <0x3>; + }; + sgenet0phy: phy@4 { + reg = <0x4>; + }; + sgenet1phy: phy@5 { + reg = <0x5>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index 30d487597ecb..fb40891ee606 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -6,9 +6,13 @@ Required properties: - reg: addresses and length of the register sets for the device, must be 6 pairs of register addresses and lengths - interrupts: interrupts for the devices, must be two interrupts +- #address-cells: must be 1, see dsa/dsa.txt +- #size-cells: must be 0, see dsa/dsa.txt + +Deprecated binding required properties: + - dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt - dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt -- #size-cells: must be 0 - #address-cells: must be 2, see dsa/dsa.txt Subnodes: @@ -48,6 +52,45 @@ switch_top@f0b00000 { ethernet_switch@0 { compatible = "brcm,bcm7445-switch-v4.0"; #size-cells = <0>; + #address-cells = <1>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + reg-names = "core", "reg", intrl2_0", "intrl2_1", + "fcb, "acb"; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + }; + }; +}; + +Example using the old DSA DeviceTree binding: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; #address-cells = <2>; reg = <0x0 0x40000 0x40000 0x110 diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt new file mode 100644 index 000000000000..dfe287a5d6f2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt @@ -0,0 +1,59 @@ +Properties for an MDIO bus multiplexer found in Broadcom iProc based SoCs. + +This MDIO bus multiplexer defines buses that could be internal as well as +external to SoCs and could accept MDIO transaction compatible to C-22 or +C-45 Clause. When child bus is selected, one needs to select these two +properties as well to generate desired MDIO transaction on appropriate bus. + +Required properties in addition to the generic multiplexer properties: + +MDIO multiplexer node: +- compatible: brcm,mdio-mux-iproc. + +Every non-ethernet PHY requires a compatible so that it could be probed based +on this compatible string. + +Additional information regarding generic multiplexer properties can be found +at- Documentation/devicetree/bindings/net/mdio-mux.txt + + +for example: + mdio_mux_iproc: mdio-mux@6602023c { + compatible = "brcm,mdio-mux-iproc"; + reg = <0x6602023c 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + + mdio@7 { + reg = <0x7>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy1: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + mdio@10 { + reg = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + gphy0: eth-phy@10 { + reg = <0x10>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt new file mode 100644 index 000000000000..22a6f10bab05 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -0,0 +1,96 @@ +Renesas R-Car CAN FD controller Device Tree Bindings +---------------------------------------------------- + +Required properties: +- compatible: Must contain one or more of the following: + - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. + - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + +- reg: physical base address and size of the R-Car CAN FD register map. +- interrupts: interrupt specifier for the Global & Channel interrupts +- clocks: phandles and clock specifiers for 3 clock inputs. +- clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Required child nodes: +The controller supports two channels and each is represented as a child node. +The name of the child nodes are "channel0" and "channel1" respectively. Each +child node supports the "status" property only, which is used to +enable/disable the respective channel. + +Required properties for "renesas,r8a7795-canfd" compatible: +In R8A7795 SoC, canfd clock is a div6 clock and can be used by both CAN +and CAN FD controller at the same time. It needs to be scaled to maximum +frequency if any of these controllers use it. This is done using the +below properties. + +- assigned-clocks: phandle of canfd clock. +- assigned-clock-rates: maximum frequency of this clock. + +Optional property: +The controller can operate in either CAN FD only mode (default) or +Classical CAN only mode. The mode is global to both the channels. In order to +enable the later, define the following optional property. + - renesas,no-can-fd: puts the controller in Classical CAN only mode. + +Example +------- + +SoC common .dtsi file: + + canfd: can@e66c0000 { + compatible = "renesas,r8a7795-canfd", + "renesas,rcar-gen3-canfd"; + reg = <0 0xe66c0000 0 0x8000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 914>, + <&cpg CPG_CORE R8A7795_CLK_CANFD>, + <&can_clk>; + clock-names = "fck", "canfd", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&cpg>; + status = "disabled"; + + channel0 { + status = "disabled"; + }; + + channel1 { + status = "disabled"; + }; + }; + +Board specific .dts file: + +E.g. below enables Channel 1 alone in the board in Classical CAN only mode. + +&canfd { + pinctrl-0 = <&canfd1_pins>; + pinctrl-names = "default"; + renesas,no-can-fd; + status = "okay"; + + channel1 { + status = "okay"; + }; +}; + +E.g. below enables Channel 0 alone in the board using External clock +as fCAN clock. + +&canfd { + pinctrl-0 = <&canfd0_pins &can_clk_pins>; + pinctrl-names = "default"; + status = "okay"; + + channel0 { + status = "okay"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt index 7dbd158810d2..e3b8fe71762b 100644 --- a/Documentation/devicetree/bindings/net/cavium-pip.txt +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -37,6 +37,12 @@ Properties for PIP port which is a child the PIP interface: - phy-handle: Optional, see ethernet.txt file in the same directory. +- rx-delay: Delay value for RGMII receive clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + +- tx-delay: Delay value for RGMII transmit clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + Example: pip@11800a0000000 { diff --git a/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt new file mode 100644 index 000000000000..c070076bacb9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt @@ -0,0 +1,13 @@ +* Cirrus Logic CS8900/CS8920 Network Controller + +Required properties: +- compatible : Should be "cirrus,cs8900" or "cirrus,cs8920". +- reg : Address and length of the IO space. +- interrupts : Should contain the controller interrupt line. + +Examples: + eth0: eth@10000000 { + compatible = "cirrus,cs8900"; + reg = <0x10000000 0x400>; + interrupts = <10>; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 0ae06491b430..5ad439f30135 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -15,7 +15,6 @@ Required properties: - cpdma_channels : Specifies number of channels in CPDMA - ale_entries : Specifies No of entries ALE can hold - bd_ram_size : Specifies internal descriptor RAM size -- rx_descs : Specifies number of Rx descriptors - mac_control : Specifies Default MAC control register content for the specific platform - slaves : Specifies number for slaves diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 0369e25aabd2..621156ca4ffd 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -2,7 +2,10 @@ TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings --------------------------------------------------- Required properties: -- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" +- compatible : Should be "ti,davinci_mdio" + and "ti,keystone_mdio" for Keystone 2 SoCs + and "ti,cpsw-mdio" for am335x, am472x, am57xx/dra7, dm814x SoCs + and "ti,am4372-mdio" for am472x SoC - reg : physical base address and size of the davinci mdio registers map - bus_freq : Mdio Bus frequency diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt new file mode 100644 index 000000000000..d6c6e41648d4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -0,0 +1,97 @@ +Broadcom BCM53xx Ethernet switches +================================== + +Required properties: + +- compatible: For external switch chips, compatible string must be exactly one + of: "brcm,bcm5325" + "brcm,bcm53115" + "brcm,bcm53125" + "brcm,bcm53128" + "brcm,bcm5365" + "brcm,bcm5395" + "brcm,bcm5397" + "brcm,bcm5398" + + For the BCM5310x SoCs with an integrated switch, must be one of: + "brcm,bcm53010-srab" + "brcm,bcm53011-srab" + "brcm,bcm53012-srab" + "brcm,bcm53018-srab" + "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string + + For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of: + "brcm,bcm58522-srab" + "brcm,bcm58523-srab" + "brcm,bcm58525-srab" + "brcm,bcm58622-srab" + "brcm,bcm58623-srab" + "brcm,bcm58625-srab" + "brcm,bcm88312-srab" and the mandatory "brcm,nsp-srab string + + For the BCM63xx/33xx SoCs with an integrated switch, must be one of: + "brcm,bcm3384-switch" + "brcm,bcm6328-switch" + "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" + +See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +required and optional properties. + +Examples: + +Ethernet switch connected via MDIO to the host, CPU port wired to eth0: + + eth0: ethernet@10001000 { + compatible = "brcm,unimac"; + reg = <0x10001000 0x1000>; + + fixed-link { + speed = <1000>; + duplex-full; + }; + }; + + mdio0: mdio@10000000 { + compatible = "brcm,unimac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + switch0: ethernet-switch@30 { + compatible = "brcm,bcm53125"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + port0@0 { + reg = <0>; + label = "lan1"; + }; + + port1@1 { + reg = <1>; + label = "lan2"; + }; + + port5@5 { + reg = <5>; + label = "cable-modem"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + }; + + port8@8 { + reg = <8>; + label = "cpu"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + ethernet = <ð0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 9f4807f90c31..a4a570fb2494 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -1,5 +1,279 @@ -Marvell Distributed Switch Architecture Device Tree Bindings ------------------------------------------------------------- +Distributed Switch Architecture Device Tree Bindings +---------------------------------------------------- + +Two bindings exist, one of which has been deprecated due to +limitations. + +Current Binding +--------------- + +Switches are true Linux devices and can be probes by any means. Once +probed, they register to the DSA framework, passing a node +pointer. This node is expected to fulfil the following binding, and +may contain additional properties as required by the device it is +embedded within. + +Required properties: + +- ports : A container for child nodes representing switch ports. + +Optional properties: + +- dsa,member : A two element list indicates which DSA cluster, and position + within the cluster a switch takes. <0 0> is cluster 0, + switch 0. <0 1> is cluster 0, switch 1. <1 0> is cluster 1, + switch 0. A switch not part of any cluster (single device + hanging off a CPU port) must not specify this property + +The ports container has the following properties + +Required properties: + +- #address-cells : Must be 1 +- #size-cells : Must be 0 + +Each port children node must have the following mandatory properties: +- reg : Describes the port address in the switch +- label : Describes the label associated with this port, which + will become the netdev name. Special labels are + "cpu" to indicate a CPU port and "dsa" to + indicate an uplink/downlink port between switches in + the cluster. + +A port labelled "dsa" has the following mandatory property: + +- link : Should be a list of phandles to other switch's DSA + port. This port is used as the outgoing port + towards the phandle ports. The full routing + information must be given, not just the one hop + routes to neighbouring switches. + +A port labelled "cpu" has the following mandatory property: + +- ethernet : Should be a phandle to a valid Ethernet device node. + This host device is what the switch port is + connected to. + +Port child nodes may also contain the following optional standardised +properties, described in binding documents: + +- phy-handle : Phandle to a PHY on an MDIO bus. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +Example + +The following example shows three switches on three MDIO busses, +linked into one DSA cluster. + +&mdio1 { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch0@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + switch0port5: port@5 { + reg = <5>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port6 + &switch2port9>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&fec1>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; +}; + +&mdio2 { + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch1@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan3"; + phy-handle = <&switch1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-handle = <&switch1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan5"; + phy-handle = <&switch1phy2>; + }; + + switch1port5: port@5 { + reg = <5>; + label = "dsa"; + link = <&switch2port9>; + phy-mode = "rgmii-txid"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch1port6: port@6 { + reg = <6>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + }; + switch1phy1: switch1phy0@1 { + reg = <1>; + }; + switch1phy2: switch1phy0@2 { + reg = <2>; + }; + }; + }; +}; + +&mdio4 { + #address-cells = <1>; + #size-cells = <0>; + + switch2: switch2@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan6"; + }; + + port@1 { + reg = <1>; + label = "lan7"; + }; + + port@2 { + reg = <2>; + label = "lan8"; + }; + + port@3 { + reg = <3>; + label = "optical3"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 2 + GPIO_ACTIVE_HIGH>; + }; + }; + + port@4 { + reg = <4>; + label = "optical4"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 3 + GPIO_ACTIVE_HIGH>; + }; + }; + + switch2port9: port@9 { + reg = <9>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port5 + &switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +Deprecated Binding +------------------ + +The deprecated binding makes use of a platform device to represent the +switches. The switches themselves are not Linux devices, and make use +of an MDIO bus for management. Required properties: - compatible : Should be "marvell,dsa" @@ -43,7 +317,7 @@ Each port children node must have the following mandatory properties: Note that a port labelled "dsa" will imply checking for the uplink phandle described below. -Optionnal property: +Optional property: - link : Should be a list of phandles to another switch's DSA port. This property is only used when switches are being chained/cascaded together. This port is used as outgoing port diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt new file mode 100644 index 000000000000..9c67ee4890d7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -0,0 +1,89 @@ +* Qualcomm Atheros QCA8xxx switch family + +Required properties: + +- compatible: should be "qca,qca8337" +- #size-cells: must be 0 +- #address-cells: must be 1 + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of +port and PHY id, each subnode describing a port needs to have a valid phandle +referencing the internal PHY connected to it. The CPU port of this switch is +always port 0. + +Example: + + + &mdio0 { + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; + }; + + switch0@0 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&phy_port5>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 5d88f37480b6..e1d76812419c 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -11,8 +11,8 @@ The following properties are common to the Ethernet controllers: the maximum frame size (there's contradiction in ePAPR). - phy-mode: string, operation mode of the PHY interface; supported values are "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", - "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto - standard property; + "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii", "trgmii"; this is now a + de-facto standard property; - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index b037a9d78d93..a1e3693cca16 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -27,6 +27,9 @@ Optional properties: number to 1. - fsl,magic-packet : If present, indicates that the hardware supports waking up via magic packet. +- fsl,err006687-workaround-present: If present indicates that the system has + the hardware workaround for ERR006687 applied and does not need a software + workaround. Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt new file mode 100644 index 000000000000..23a39a309d17 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt @@ -0,0 +1,22 @@ +Hisilicon Fast Ethernet MDIO Controller interface + +Required properties: +- compatible: should be "hisilicon,hisi-femac-mdio". +- reg: address and length of the register set for the device. +- clocks: A phandle to the reference clock for this device. + +- PHY subnode: inherits from phy binding [1] +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: +mdio: mdio@10091100 { + compatible = "hisilicon,hisi-femac-mdio"; + reg = <0x10091100 0x10>; + clocks = <&crg HI3516CV300_MDIO_CLK>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@1 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac.txt b/Documentation/devicetree/bindings/net/hisilicon-femac.txt new file mode 100644 index 000000000000..d11af5ecace8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac.txt @@ -0,0 +1,39 @@ +Hisilicon Fast Ethernet MAC controller + +Required properties: +- compatible: should contain one of the following version strings: + * "hisilicon,hisi-femac-v1" + * "hisilicon,hisi-femac-v2" + and the soc string "hisilicon,hi3516cv300-femac". +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC core register base and size. + The second region is the global MAC control register. +- interrupts: should contain the MAC interrupt. +- clocks: A phandle to the MAC main clock. +- resets: should contain the phandle to the MAC reset signal(required) and + the PHY reset signal(optional). +- reset-names: should contain the reset signal name "mac"(required) + and "phy"(optional). +- mac-address: see ethernet.txt [1]. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + +Example: + hisi_femac: ethernet@10090000 { + compatible = "hisilicon,hi3516cv300-femac","hisilicon,hisi-femac-v2"; + reg = <0x10090000 0x1000>,<0x10091300 0x200>; + interrupts = <12>; + clocks = <&crg HI3518EV200_ETH_CLK>; + resets = <&crg 0xec 0>,<&crg 0xec 3>; + reset-names = "mac","phy"; + mac-address = [00 00 00 00 00 00]; + phy-mode = "mii"; + phy-handle = <&phy0>; + hisilicon,phy-reset-delays-us = <10000 20000 20000>; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index b9ff4ba6454e..f0421ee3c714 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -8,7 +8,7 @@ Required properties: specifies a reference to the associating hardware driver node. see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt - port-id: is the index of port provided by DSAF (the accelerator). DSAF can - connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They + connect to 8 PHYs. Port 0 to 1 are both used for administration purpose. They are called debug ports. The remaining 6 PHYs are taken according to the mode of DSAF. diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index b30ab6b5cbfa..04ba1dc34fd6 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -2,7 +2,7 @@ This document describes the device tree bindings associated with the keystone network coprocessor(NetCP) driver support. The network coprocessor (NetCP) is a hardware accelerator that processes -Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet +Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet switch sub-module to send and receive packets. NetCP also includes a packet accelerator (PA) module to perform packet classification operations such as header matching, and packet modification operations such as checksum diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index b5a42df4c928..1506e948610c 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -21,6 +21,7 @@ Required properties: - clock-names: Tuple listing input clock names. Required elements: 'pclk', 'hclk' Optional elements: 'tx_clk' + Optional elements: 'rx_clk' applies to cdns,zynqmp-gem - clocks: Phandles to input clocks. Optional properties for PHY child node: diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt index 14aa6cf58201..6a9a63cb0543 100644 --- a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt +++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt @@ -13,10 +13,10 @@ Optional properties: initialization. This is an array of 28 values(u8). - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. - firmware will use the pin to wakeup host system. + firmware will use the pin to wakeup host system (u16). - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host platform. The value will be configured to firmware. This - is needed to work chip's sleep feature as expected. + is needed to work chip's sleep feature as expected (u16). - interrupt-parent: phandle of the parent interrupt controller - interrupts : interrupt pin number to the cpu. Driver will request an irq based on this interrupt number. During system suspend, the irq will be @@ -50,7 +50,7 @@ calibration data is also available in below example. 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xf0 0x00>; - marvell,wakeup-pin = <0x0d>; - marvell,wakeup-gap-ms = <0x64>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; }; }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt index 491f5bd55203..f58571f36570 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -5,11 +5,12 @@ numbered uniquely in a device dependent manner. The nodes for an MDIO bus multiplexer/switch will have one child node for each child bus. Required properties: -- mdio-parent-bus : phandle to the parent MDIO bus. - #address-cells = <1>; - #size-cells = <0>; Optional properties: +- mdio-parent-bus : phandle to the parent MDIO bus. + - Other properties specific to the multiplexer/switch hardware. Required properties for child nodes: diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 32eaaca04d9b..f09525772369 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -24,14 +24,17 @@ Required properties: Optional properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - +- mediatek,hwlro: the capability if the hardware supports LRO functions * Ethernet MAC node Required properties: - compatible: Should be "mediatek,eth-mac" - reg: The number of the MAC -- phy-handle: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory and + the phy-mode "trgmii" required being provided when reg + is equal to 0 and the MAC uses fixed-link to connect + with internal switch such as MT7530. Example: @@ -51,6 +54,7 @@ eth: ethernet@1b100000 { reset-names = "eth"; mediatek,ethsys = <ðsys>; mediatek,pctl = <&syscfg_pctl_a>; + mediatek,hwlro; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt index 87496a8c64ab..8d157f0295a5 100644 --- a/Documentation/devicetree/bindings/net/micrel.txt +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -35,3 +35,13 @@ Optional properties: supported clocks: - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference input clock. Used to determine the XI input clock. + + - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode + + Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled + by the FXEN boot strapping pin. It can't be determined from the PHY + registers whether the PHY is in fiber mode, so this boolean device tree + property can be used to describe it. + + In fiber mode, auto-negotiation is disabled and the PHY can only work in + 100base-fx (full and half duplex) modes. diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt new file mode 100644 index 000000000000..99c7eb0a00c8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -0,0 +1,58 @@ +* Microsemi - vsc8531 Giga bit ethernet phy + +Required properties: +- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" + The PHY device uses the binding described in + Documentation/devicetree/bindings/net/phy.txt + +Optional properties: +- vsc8531,vddmac : The vddmac in mV. +- vsc8531,edge-slowdown : % the edge should be slowed down relative to + the fastest possible edge time. Native sign + need not enter. + Edge rate sets the drive strength of the MAC + interface output signals. Changing the drive + strength will affect the edge rate of the output + signal. The goal of this setting is to help + reduce electrical emission (EMI) by being able + to reprogram drive strength and in effect slow + down the edge rate if desired. Table 1 shows the + impact to the edge rate per VDDMAC supply for each + drive strength setting. + Ref: Table:1 - Edge rate change below. + +Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values + +Table: 1 - Edge rate change +----------------------------------------------------------------| +| Edge Rate Change (VDDMAC) | +| | +| 3300 mV 2500 mV 1800 mV 1500 mV | +|---------------------------------------------------------------| +| Default Deafult Default Default | +| (Fastest) (recommended) (recommended) | +|---------------------------------------------------------------| +| -2% -3% -5% -6% | +|---------------------------------------------------------------| +| -4% -6% -9% -14% | +|---------------------------------------------------------------| +| -7% -10% -16% -21% | +|(recommended) (recommended) | +|---------------------------------------------------------------| +| -10% -14% -23% -29% | +|---------------------------------------------------------------| +| -17% -23% -35% -42% | +|---------------------------------------------------------------| +| -29% -37% -52% -58% | +|---------------------------------------------------------------| +| -53% -63% -76% -77% | +| (slowest) | +|---------------------------------------------------------------| + +Example: + + vsc8531_0: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.0570"; + vsc8531,vddmac = <3300>; + vsc8531,edge-slowdown = <21>; + }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index c00a9a894547..bc1c3c8bf8fa 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -35,8 +35,6 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. -- reset-gpios: Reference to a GPIO used to reset the phy. - Example: ethernet-phy@0 { @@ -44,5 +42,4 @@ ethernet-phy@0 { interrupt-parent = <40000>; interrupts = <35 1>; reg = <0>; - reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt new file mode 100644 index 000000000000..346e6c7f47b7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt @@ -0,0 +1,111 @@ +Qualcomm Technologies EMAC Gigabit Ethernet Controller + +This network controller consists of two devices: a MAC and an SGMII +internal PHY. Each device is represented by a device tree node. A phandle +connects the MAC node to its corresponding internal phy node. Another +phandle points to the external PHY node. + +Required properties: + +MAC node: +- compatible : Should be "qcom,fsm9900-emac". +- reg : Offset and length of the register regions for the device +- interrupts : Interrupt number used by this controller +- mac-address : The 6-byte MAC address. If present, it is the default + MAC address. +- internal-phy : phandle to the internal PHY node +- phy-handle : phandle the the external PHY node + +Internal PHY node: +- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii". +- reg : Offset and length of the register region(s) for the device +- interrupts : Interrupt number used by this controller + +The external phy child node: +- reg : The phy address + +Example: + +FSM9900: + +soc { + #address-cells = <1>; + #size-cells = <1>; + + emac0: ethernet@feb20000 { + compatible = "qcom,fsm9900-emac"; + reg = <0xfeb20000 0x10000>, + <0xfeb36000 0x1000>; + interrupts = <76>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + }; + + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins_a>; + }; + + emac_sgmii: ethernet@feb38000 { + compatible = "qcom,fsm9900-emac-sgmii"; + reg = <0xfeb38000 0x1000>; + interrupts = <80>; + }; + + tlmm: pinctrl@fd510000 { + compatible = "qcom,fsm9900-pinctrl"; + + mdio_pins_a: mdio { + state { + pins = "gpio123", "gpio124"; + function = "mdio"; + }; + }; + }; + + +QDF2432: + +soc { + #address-cells = <2>; + #size-cells = <2>; + + emac0: ethernet@38800000 { + compatible = "qcom,fsm9900-emac"; + reg = <0x0 0x38800000 0x0 0x10000>, + <0x0 0x38816000 0x0 0x1000>; + interrupts = <0 256 4>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@4 { + reg = <4>; + }; + }; + + emac_sgmii: ethernet@410400 { + compatible = "qcom,qdf2432-emac-sgmii"; + reg = <0x0 0x00410400 0x0 0xc00>, /* Base address */ + <0x0 0x00410000 0x0 0x400>; /* Per-lane digital */ + interrupts = <0 254 1>; + }; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt index 93eac7ce1446..95383c5131fc 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -3,7 +3,12 @@ Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) The device node has following properties. Required properties: - - compatible: Can be one of "rockchip,rk3288-gmac", "rockchip,rk3368-gmac" + - compatible: should be "rockchip,<name>-gamc" + "rockchip,rk3228-gmac": found on RK322x SoCs + "rockchip,rk3288-gmac": found on RK3288 SoCs + "rockchip,rk3366-gmac": found on RK3366 SoCs + "rockchip,rk3368-gmac": found on RK3368 SoCs + "rockchip,rk3399-gmac": found on RK3399 SoCs - reg: addresses and length of the register sets for the device. - interrupts: Should contain the GMAC interrupts. - interrupt-names: Should contain the interrupt names "macirq". diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 2f6ec85fda8e..0115c85a2425 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -5,6 +5,8 @@ interface contains. Required properties: - compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. + "renesas,ether-r8a7743" if the device is a part of R8A7743 SoC. + "renesas,ether-r8a7745" if the device is a part of R8A7745 SoC. "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt index 3fed3c124411..16c3a9501f5d 100644 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -3,9 +3,11 @@ Required properties: - compatible : Should be "smsc,lan<model>", "smsc,lan9115" - reg : Address and length of the io space for SMSC LAN -- interrupts : Should contain SMSC LAN interrupt line -- interrupt-parent : Should be the phandle for the interrupt controller - that services interrupts for this device +- interrupts : one or two interrupt specifiers + - The first interrupt is the SMSC LAN interrupt line + - The second interrupt (if present) is the PME (power + management event) interrupt that is able to wake up the host + system with a 50ms pulse on network activity - phy-mode : See ethernet.txt file in the same directory Optional properties: @@ -21,6 +23,10 @@ Optional properties: external PHY - smsc,save-mac-address : Indicates that mac address needs to be saved before resetting the controller +- reset-gpios : a GPIO line connected to the RESET (active low) signal + of the device. On many systems this is wired high so the device goes + out of reset at power-on, but if it is under program control, this + optional GPIO can wake up in response to it. Examples: @@ -29,7 +35,8 @@ lan9220@f4000000 { reg = <0xf4000000 0x2000000>; phy-mode = "mii"; interrupt-parent = <&gpio1>; - interrupts = <31>; + interrupts = <31>, <32>; + reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; reg-io-width = <4>; smsc,irq-push-pull; }; diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt index 51f8d2eba8d8..d93f71ce8346 100644 --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -1,21 +1,111 @@ * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) +This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) +IP block. The IP supports multiple options for bus type, clocking and reset +structure, and feature list. Consequently, a number of properties and list +entries in properties are marked as optional, or only required in specific HW +configurations. Required properties: -- compatible: Should be "snps,dwc-qos-ethernet-4.10" +- compatible: One of: + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the Axis ARTPEC-6 SoC. + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the NVIDIA Tegra186 SoC. + - "snps,dwc-qos-ethernet-4.10" + This combination is deprecated. It should be treated as equivalent to + "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be + compatible with earlier revisions of this binding. - reg: Address and length of the register set for the device -- clocks: Phandles to the reference clock and the bus clock -- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk" - for the bus clock. +- clocks: Phandle and clock specifiers for each entry in clock-names, in the + same order. See ../clock/clock-bindings.txt. +- clock-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "tx" + The EQOS transmit path clock. The HW signal name is clk_tx_i. + In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX + path. In other configurations, other clocks (such as tx_125, rmii) may + drive the PHY TX path. + - "rx" + The EQOS receive path clock. The HW signal name is clk_rx_i. + In some configurations (e.g. GMII/RGMII), this clock is derived from the + PHY's RX clock output. In other configurations, other clocks (such as + rx_125, rmii) may drive the EQOS RX path. + In cases where the PHY clock is directly fed into the EQOS receive path + without intervening logic, the DT need not represent this clock, since it + is assumed to be fully under the control of the PHY device/driver. In + cases where SoC integration adds additional logic to this path, such as a + SW-controlled clock gate, this clock should be represented in DT. + - "slave_bus" + The CPU/slave-bus (CSR) interface clock. This applies to any bus type; + APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other + buses). + - "master_bus" + The master bus interface clock. Only required in configurations that use a + separate clock for the master and slave bus interfaces. The HW signal name + is hclk_i (AHB) or aclk_i (AXI). + - "ptp_ref" + The PTP reference clock. The HW signal name is clk_ptp_ref_i. + - "phy_ref_clk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "tx". + - "apb_pclk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "slave_bus". + + Note: Support for additional IP configurations may require adding the + following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i, + clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i. + Configurations exist where multiple similar clocks are used at once, e.g. all + of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to + extend the binding with a separate clock-names entry for each of those RX + clocks, rather than repurposing the existing "rx" clock-names entry as a + generic/logical clock in a similar fashion to "master_bus" and "slave_bus". + This will allow easy support for configurations that support multiple PHY + interfaces using a mux, and hence need to have explicit control over + specific RX clocks. + + The following compatible values require the following set of clocks: + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "rx" + - "tx" + - "ptp_ref" + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "tx" + - "ptp_ref" + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - "phy_ref_clk" + - "apb_clk" - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the core's combined interrupt signal - phy-mode: See ethernet.txt file in the same directory +- resets: Phandle and reset specifiers for each entry in reset-names, in the + same order. See ../reset/reset.txt. +- reset-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "eqos". The reset to the entire module. The HW signal name is hreset_n + (AHB) or aresetn_i (AXI). + + The following compatible values require the following set of resets: + (the reset properties may be omitted if empty) + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "eqos". + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - None. + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - None. Optional properties: - dma-coherent: Present if dma operations are coherent - mac-address: See ethernet.txt in the same directory - local-mac-address: See ethernet.txt in the same directory +- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY. + See ../gpio/gpio.txt. - snps,en-lpi: If present it enables use of the AXI low-power interface - snps,write-requests: Number of write requests that the AXI port can issue. It depends on the SoC configuration. @@ -52,6 +142,7 @@ ethernet2@40010000 { reg = <0x40010000 0x4000>; phy-handle = <&phy2>; phy-mode = "gmii"; + phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>; snps,en-tx-lpi-clockgating; snps,en-lpi; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 72d82d684342..2e68a3cd8513 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -17,9 +17,26 @@ Required properties: Optional properties: altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if DWMAC controller is connected emac splitter. +phy-mode: The phy mode the ethernet operates in +altr,sgmii-to-sgmii-converter: phandle to the TSE SGMII converter + +This device node has additional phandle dependency, the sgmii converter: + +Required properties: + - compatible : Should be altr,gmii-to-sgmii-2.0 + - reg-names : Should be "eth_tse_control_port" Example: +gmii_to_sgmii_converter: phy@0x100000240 { + compatible = "altr,gmii-to-sgmii-2.0"; + reg = <0x00000001 0x00000240 0x00000008>, + <0x00000001 0x00000200 0x00000040>; + reg-names = "eth_tse_control_port"; + clocks = <&sgmii_1_clk_0 &emac1 1 &sgmii_clk_125 &sgmii_clk_125>; + clock-names = "tse_pcs_ref_clk_clock_connection", "tse_rx_cdr_refclk"; +}; + gmac0: ethernet@ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; altr,sysmgr-syscon = <&sysmgr 0x60 0>; @@ -30,4 +47,6 @@ gmac0: ethernet@ff700000 { mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ clocks = <&emac_0_clk>; clock-names = "stmmaceth"; + phy-mode = "sgmii"; + altr,gmii-to-sgmii-converter = <&gmii_to_sgmii_converter>; }; diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt new file mode 100644 index 000000000000..c35afb7e956a --- /dev/null +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -0,0 +1,32 @@ +STMicroelectronics STM32 / MCU DWMAC glue layer controller + +This file documents platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: Should be "st,stm32-dwmac" to select glue, and + "snps,dwmac-3.50a" to select IP version. +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: Should be "stmmaceth" for the host clock. + Should be "mac-clk-tx" for the MAC TX clock. + Should be "mac-clk-rx" for the MAC RX clock. +- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. +Example: + + ethernet@40028000 { + compatible = "st,stm32-dwmac", "snps,dwmac-3.50a"; + status = "disabled"; + reg = <0x40028000 0x8000>; + reg-names = "stmmaceth"; + interrupts = <0 61 0>, <0 62 0>; + interrupt-names = "macirq", "eth_wake_irq"; + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx"; + clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>; + st,syscon = <&syscfg 0x4>; + snps,pbl = <8>; + snps,mixed-burst; + dma-ranges; + }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 4d302db657c0..41b49e6075f5 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -47,12 +47,15 @@ Optional properties: supported by this device instance - snps,perfect-filter-entries: Number of perfect filter entries supported by this device instance +- snps,ps-speed: port selection speed that can be passed to the core when + PCS is supported. For example, this is used in case of SGMII + and MAC2MAC connection. - AXI BUS Mode parameters: below the list of all the parameters to program the AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface - snps,xit_frm: unlock on WoL - - snps,wr_osr_lmt: max write oustanding req. limit - - snps,rd_osr_lmt: max read oustanding req. limit + - snps,wr_osr_lmt: max write outstanding req. limit + - snps,rd_osr_lmt: max read outstanding req. limit - snps,kbbe: do not cross 1KiB boundary. - snps,axi_all: align address - snps,blen: this is a vector of supported burst length. diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 58d935b58598..5d21141a68b5 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -2,7 +2,7 @@ Required properties: - reg - The ID number for the phy, usually a small integer - - ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h + - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt new file mode 100644 index 000000000000..19331bb4ff6e --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt @@ -0,0 +1,31 @@ +Espressif ESP8089 wireless SDIO devices + +This node provides properties for controlling the ESP8089 wireless device. +The node is expected to be specified as a child node to the SDIO controller +that connects the device to the system. + +Required properties: + + - compatible : Should be "esp,esp8089". + +Optional properties: + - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter + +Example: + +&mmc1 { + #address-cells = <1>; + #size-cells = <0>; + + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt index 9180724e182c..8f9ced076fe1 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -1,19 +1,30 @@ -* Texas Instruments wl1271 wireless lan controller +* Texas Instruments wl12xx/wl18xx wireless lan controller -The wl1271 chip can be connected via SPI or via SDIO. This +The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This document describes the binding for the SPI connected chip. Required properties: -- compatible : Should be "ti,wl1271" +- compatible : Should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" - reg : Chip select address of device - spi-max-frequency : Maximum SPI clocking speed of device in Hz -- ref-clock-frequency : Reference clock frequency - interrupt-parent, interrupts : Should contain parameters for 1 interrupt line. Interrupt parameters: parent, line number, type. -- vwlan-supply : Point the node of the regulator that powers/enable the wl1271 chip +- vwlan-supply : Point the node of the regulator that powers/enable the + wl12xx/wl18xx chip Optional properties: +- ref-clock-frequency : Reference clock frequency (should be set for wl12xx) - clock-xtal : boolean, clock is generated from XTAL - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt @@ -21,16 +32,28 @@ Optional properties: Examples: +For wl12xx family: &spi1 { - wl1271@1 { + wlcore: wlcore@1 { compatible = "ti,wl1271"; - reg = <1>; spi-max-frequency = <48000000>; - clock-xtal; - ref-clock-frequency = <38400000>; interrupt-parent = <&gpio3>; interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; +}; + +For wl18xx family: +&spi0 { + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; }; }; diff --git a/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt new file mode 100644 index 000000000000..038dda48b8e6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt @@ -0,0 +1,35 @@ +XILINX GMIITORGMII Converter Driver Device Tree Bindings +-------------------------------------------------------- + +The Gigabit Media Independent Interface (GMII) to Reduced Gigabit Media +Independent Interface (RGMII) core provides the RGMII between RGMII-compliant +Ethernet physical media devices (PHY) and the Gigabit Ethernet controller. +This core can be used in all three modes of operation(10/100/1000 Mb/s). +The Management Data Input/Output (MDIO) interface is used to configure the +Speed of operation. This core can switch dynamically between the three +Different speed modes by configuring the conveter register through mdio write. + +This converter sits between the ethernet MAC and the external phy. +MAC <==> GMII2RGMII <==> RGMII_PHY + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Should be "xlnx,gmii-to-rgmii-1.0" +- reg : The ID number for the phy, usually a small integer +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. + +Example: + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy: ethernet-phy@0 { + ...... + }; + gmiitorgmii: gmiitorgmii@8 { + compatible = "xlnx,gmii-to-rgmii-1.0"; + reg = <8>; + phy-handle = <&phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt index 8f86ab3b1046..94aeeeabadd5 100644 --- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -1,11 +1,20 @@ = Rockchip eFuse device tree bindings = Required properties: -- compatible: Should be "rockchip,rockchip-efuse" +- compatible: Should be one of the following. + - "rockchip,rk3066a-efuse" - for RK3066a SoCs. + - "rockchip,rk3188-efuse" - for RK3188 SoCs. + - "rockchip,rk3288-efuse" - for RK3288 SoCs. + - "rockchip,rk3399-efuse" - for RK3399 SoCs. - reg: Should contain the registers location and exact eFuse size - clocks: Should be the clock id of eFuse - clock-names: Should be "pclk_efuse" +Deprecated properties: +- compatible: "rockchip,rockchip-efuse" + Old efuse compatible value compatible to rk3066a, rk3188 and rk3288 + efuses + = Data cells = Are child nodes of eFuse, bindings of which as described in bindings/nvmem/nvmem.txt @@ -13,7 +22,7 @@ bindings/nvmem/nvmem.txt Example: efuse: efuse@ffb40000 { - compatible = "rockchip,rockchip-efuse"; + compatible = "rockchip,rk3288-efuse"; reg = <0xffb40000 0x20>; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 601256fe8c0d..ee91cbdd95ee 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -45,7 +45,7 @@ Devices supporting OPPs must set their "operating-points-v2" property with phandle to a OPP table in their DT node. The OPP core will use this phandle to find the operating points for the device. -If required, this can be extended for SoC vendor specfic bindings. Such bindings +If required, this can be extended for SoC vendor specific bindings. Such bindings should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt and should have a compatible description like: "operating-points-v2-<vendor>". diff --git a/Documentation/devicetree/bindings/pci/aardvark-pci.txt b/Documentation/devicetree/bindings/pci/aardvark-pci.txt new file mode 100644 index 000000000000..bbcd9f4c501f --- /dev/null +++ b/Documentation/devicetree/bindings/pci/aardvark-pci.txt @@ -0,0 +1,56 @@ +Aardvark PCIe controller + +This PCIe controller is used on the Marvell Armada 3700 ARM64 SoC. + +The Device Tree node describing an Aardvark PCIe controller must +contain the following properties: + + - compatible: Should be "marvell,armada-3700-pcie" + - reg: range of registers for the PCIe controller + - interrupts: the interrupt line of the PCIe controller + - #address-cells: set to <3> + - #size-cells: set to <2> + - device_type: set to "pci" + - ranges: ranges for the PCI memory and I/O regions + - #interrupt-cells: set to <1> + - msi-controller: indicates that the PCIe controller can itself + handle MSI interrupts + - msi-parent: pointer to the MSI controller to be used + - interrupt-map-mask and interrupt-map: standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + - bus-range: PCI bus numbers covered + +In addition, the Device Tree describing an Aardvark PCIe controller +must include a sub-node that describes the legacy interrupt controller +built into the PCIe controller. This sub-node must have the following +properties: + + - interrupt-controller + - #interrupt-cells: set to <1> + +Example: + + pcie0: pcie@d0070000 { + compatible = "marvell,armada-3700-pcie"; + device_type = "pci"; + status = "disabled"; + reg = <0 0xd0070000 0 0x20000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + msi-controller; + msi-parent = <&pcie0>; + ranges = <0x82000000 0 0xe8000000 0 0xe8000000 0 0x1000000 /* Port 0 MEM */ + 0x81000000 0 0xe9000000 0 0xe9000000 0 0x10000>; /* Port 0 IO*/ + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, + <0 0 0 2 &pcie_intc 1>, + <0 0 0 3 &pcie_intc 2>, + <0 0 0 4 &pcie_intc 3>; + pcie_intc: interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt new file mode 100644 index 000000000000..5ecaea1e6eee --- /dev/null +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -0,0 +1,47 @@ +* Axis ARTPEC-6 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "axis,artpec6-pcie", "snps,dw-pcie" +- reg: base addresses and lengths of the PCIe controller (DBI), + the phy controller, and configuration address space. +- reg-names: Must include the following entries: + - "dbi" + - "phy" + - "config" +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller, + used to enable and control the Synopsys IP. + +Example: + + pcie@f8050000 { + compatible = "axis,artpec6-pcie", "snps,dw-pcie"; + reg = <0xf8050000 0x2000 + 0xf8040000 0x1000 + 0xc0000000 0x2000>; + reg-names = "dbi", "phy", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + /* downstream I/O */ + ranges = <0x81000000 0 0 0xc0002000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>; + num-lanes = <2>; + bus-range = <0x00 0xff>; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + axis,syscon-pcie = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 64f2fff12128..1392c705ceca 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -17,6 +17,8 @@ Required properties: - num-lanes: number of lanes to use Optional properties: +- num-viewport: number of view ports configured in hardware. If a platform + does not specify it, the driver assumes 2. - num-lanes: number of lanes to use (this property should be specified unless the link is brought already up in BIOS) - reset-gpio: gpio pin number of power good signal @@ -31,7 +33,7 @@ Optional properties: Example configuration: - pcie: pcie@0xdffff000 { + pcie: pcie@dffff000 { compatible = "snps,dw-pcie"; reg = <0xdffff000 0x1000>, /* Controller registers */ <0xd0000000 0x2000>; /* PCI config space */ @@ -44,4 +46,5 @@ Example configuration: interrupts = <25>, <24>; #interrupt-cells = <1>; num-lanes = <1>; + num-viewport = <3>; }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 3be80c68941a..83aeb1f5a645 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "fsl,imx6q-pcie" -- reg: base addresse and length of the pcie controller +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie" +- reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: @@ -19,6 +19,20 @@ Optional properties: - fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" Example: diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index b721beacfe4d..59c2f47aa303 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -34,11 +34,11 @@ Hip05 Example (note that Hip06 is the same except compatible): ranges = <0x82000000 0 0x00000000 0x220 0x00000000 0 0x10000000>; num-lanes = <8>; port-id = <1>; - #interrupts-cells = <1>; - interrupts-map-mask = <0xf800 0 0 7>; - interrupts-map = <0x0 0 0 1 &mbigen_pcie 1 10 - 0x0 0 0 2 &mbigen_pcie 2 11 - 0x0 0 0 3 &mbigen_pcie 3 12 - 0x0 0 0 4 &mbigen_pcie 4 13>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie 1 10 + 0x0 0 0 2 &mbigen_pcie 2 11 + 0x0 0 0 3 &mbigen_pcie 3 12 + 0x0 0 0 4 &mbigen_pcie 4 13>; status = "ok"; }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index ef683b2fd23a..41e9f55a1467 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -24,6 +24,9 @@ Required properties: The first entry must be a link to the SCFG device node The second entry must be '0' or '1' based on physical PCIe controller index. This is used to get SCFG PEXN registers +- dma-coherent: Indicates that the hardware IP block can ensure the coherency + of the data transferred from/to the IP block. This can avoid the software + cache flush/invalid actions, and improve the performance significantly. Example: @@ -38,6 +41,7 @@ Example: #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 75321ae23c08..b8cc395fffea 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -60,11 +60,14 @@ Required properties: - afi - pcie_x -Required properties on Tegra124 and later: +Required properties on Tegra124 and later (deprecated): - phys: Must contain an entry for each entry in phy-names. - phy-names: Must include the following entries: - pcie +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -122,11 +125,22 @@ Required properties: - Root port 0 uses 4 lanes, root port 1 is unused. - Both root ports use 2 lanes. -Example: +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. Note that the number + of entries does not have to (though usually will) be equal to the specified + number of lanes in the nvidia,num-lanes property. Entries are of the form + "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. + +Examples: +========= + +Tegra20: +-------- SoC DTSI: - pcie-controller { + pcie-controller@80003000 { compatible = "nvidia,tegra20-pcie"; device_type = "pci"; reg = <0x80003000 0x00000800 /* PADS registers */ @@ -186,10 +200,9 @@ SoC DTSI: }; }; - Board DTS: - pcie-controller { + pcie-controller@80003000 { status = "okay"; vdd-supply = <&pci_vdd_reg>; @@ -222,3 +235,204 @@ if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, device nodes need to be added in order to allow the bus' children to be instantiated at the proper location in the operating system's device tree (as illustrated by the optional nodes in the example above). + +Tegra30: +-------- + +SoC DTSI: + + pcie-controller@00003000 { + compatible = "nvidia,tegra30-pcie"; + device_type = "pci"; + reg = <0x00003000 0x00000800 /* PADS registers */ + 0x00003800 0x00000200 /* AFI registers */ + 0x10000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH /* controller interrupt */ + GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ + 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ + + clocks = <&tegra_car TEGRA30_CLK_PCIE>, + <&tegra_car TEGRA30_CLK_AFI>, + <&tegra_car TEGRA30_CLK_PLL_E>, + <&tegra_car TEGRA30_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@00003000 { + status = "okay"; + + avdd-pexa-supply = <&ldo1_reg>; + vdd-pexa-supply = <&ldo1_reg>; + avdd-pexb-supply = <&ldo1_reg>; + vdd-pexb-supply = <&ldo1_reg>; + avdd-pex-pll-supply = <&ldo1_reg>; + avdd-plle-supply = <&ldo1_reg>; + vddio-pex-ctl-supply = <&sys_3v3_reg>; + hvdd-pex-supply = <&sys_3v3_pexs_reg>; + + pci@1,0 { + status = "okay"; + }; + + pci@3,0 { + status = "okay"; + }; + }; + +Tegra124: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra124-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA124_CLK_PCIE>, + <&tegra_car TEGRA124_CLK_AFI>, + <&tegra_car TEGRA124_CLK_PLL_E>, + <&tegra_car TEGRA124_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-supply = <&vdd_3v3_lp0>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + vddio-pex-ctl-supply = <&vdd_3v3_lp0>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + + /* Mini PCIe */ + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + + /* Gigabit Ethernet */ + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt new file mode 100644 index 000000000000..598533a57d79 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -0,0 +1,38 @@ +* Marvell Armada 7K/8K PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "marvell,armada8k-pcie" +- reg: must contain two register regions + - the control register region + - the config space region +- reg-names: + - "ctrl" for the control register region + - "config" for the config space region +- interrupts: Interrupt specifier for the PCIe controler +- clocks: reference to the PCIe controller clock + +Example: + + pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 /* downstream I/O */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; /* non-prefetchable memory */ + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 54eae2938174..d08a4d51108f 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -56,6 +56,7 @@ Optional properties:- phy-names: name of the Generic Keystine SerDes phy for PCI - If boot loader already does PCI link establishment, then phys and phy-names shouldn't be present. + interrupts: platform interrupt for error interrupts. Designware DT Properties not applicable for Keystone PCI diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt new file mode 100644 index 000000000000..ba67b39939c1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -0,0 +1,106 @@ +* Rockchip AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "rockchip,rk3399-pcie" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "axi-base" + - "apb-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- msi-map: Maps a Requester ID to an MSI controller and associated + msi-specifier data. See ./pci-msi.txt +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". +- interrupts: Three interrupt entries must be specified. +- interrupt-names: Must include the following names + - "sys" + - "legacy" + - "client" +- resets: Must contain five entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-map-mask and interrupt-map: standard PCI properties + +Optional Property: +- ep-gpios: contain the entry for pre-reset gpio +- num-lanes: number of lanes to use +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe. +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe. + +*Interrupt controller child node* +The core controller provides a single interrupt for legacy INTx. The PCIe node +should contain an interrupt controller node as a target for the PCI +'interrupt-map' property. This node represents the domain at which the four +INTx interrupts are decoded and routed. + + +Required properties for Interrupt controller child node: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +Example: + +pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + bus-range = <0x0 0x1>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "legacy", "client"; + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; + assigned-clock-rates = <100000000>; + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; + num-lanes = <4>; + msi-map = <0x0 &its 0x0 0x1000>; + reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; + reg-names = "axi-base", "apb-base"; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0_intc 0>, + <0 0 0 2 &pcie0_intc 1>, + <0 0 0 3 &pcie0_intc 2>, + <0 0 0 4 &pcie0_intc 3>; + pcie0_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt index 337fc97d18c9..3259798a1192 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -55,9 +55,10 @@ nwl_pcie: pcie@fd0e0000 { msi-parent = <&nwl_pcie>; reg = <0x0 0xfd0e0000 0x0 0x1000>, <0x0 0xfd480000 0x0 0x1000>, - <0x0 0xe0000000 0x0 0x1000000>; + <0x80 0x00000000 0x0 0x1000000>; reg-names = "breg", "pcireg", "cfg"; - ranges = <0x02000000 0x00000000 0xe1000000 0x00000000 0xe1000000 0 0x0f000000>; + ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 0xe0000000 0x00000000 0x10000000 /* non-prefetchable memory */ + 0x43000000 0x00000006 0x00000000 0x00000006 0x00000000 0x00000002 0x00000000>;/* prefetchable memory */ pcie_intc: legacy-interrupt-controller { interrupt-controller; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt new file mode 100644 index 000000000000..a7aee9ea8926 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt @@ -0,0 +1,21 @@ +Driver for Broadcom Northstar USB 2.0 PHY + +Required properties: +- compatible: brcm,ns-usb2-phy +- reg: iomem address range of DMU (Device Management Unit) +- reg-names: "dmu", the only needed & supported reg right now +- clocks: USB PHY reference clock +- clock-names: "phy-ref-clk", the only needed & supported clock right now + +To initialize USB 2.0 PHY driver needs to setup PLL correctly. To do this it +requires passing phandle to the USB PHY reference clock. + +Example: + usb2-phy { + compatible = "brcm,ns-usb2-phy"; + reg = <0x1800c000 0x1000>; + reg-names = "dmu"; + #phy-cells = <0>; + clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>; + clock-names = "phy-ref-clk"; + }; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt new file mode 100644 index 000000000000..09aeba94538d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt @@ -0,0 +1,23 @@ +Driver for Broadcom Northstar USB 3.0 PHY + +Required properties: + +- compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy". +- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B + MMI. +- reg-names: "dmp" and "ccb-mii" + +Initialization of USB 3.0 PHY depends on Northstar version. There are currently +three known series: Ax, Bx and Cx. +Known A0: BCM4707 rev 0 +Known B0: BCM4707 rev 4, BCM53573 rev 2 +Known B1: BCM4707 rev 6 +Known C0: BCM47094 rev 0 + +Example: + usb3-phy { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x18105000 0x1000>, <0x18003000 0x1000>; + reg-names = "dmp", "ccb-mii"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt new file mode 100644 index 000000000000..5b51007c6f24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt @@ -0,0 +1,27 @@ +* Broadcom NS2 PCIe PHY binding document + +Required bus properties: +- reg: MDIO Bus number for the MDIO interface +- #address-cells: must be 1 +- #size-cells: must be 0 + +Required PHY properties: +- compatible: should be "brcm,ns2-pcie-phy" +- reg: MDIO Phy ID for the MDIO interface +- #phy-cells: must be 0 + +This is a child bus node of "brcm,mdio-mux-iproc" node. + +Example: + +mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index d87ab7c127b8..6ccce09d8bbf 100644 --- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -1,14 +1,18 @@ -* Broadcom SATA3 PHY for STB +* Broadcom SATA3 PHY Required properties: - compatible: should be one or more of "brcm,bcm7425-sata-phy" "brcm,bcm7445-sata-phy" + "brcm,iproc-ns2-sata-phy" + "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" - address-cells: should be 1 - size-cells: should be 0 -- reg: register range for the PHY PCB interface -- reg-names: should be "phy" +- reg: register ranges for the PHY PCB interface +- reg-names: should be "phy" and "phy-ctrl" + The "phy-ctrl" registers are only required for + "brcm,iproc-ns2-sata-phy". Sub-nodes: Each port's PHY should be represented as a sub-node. @@ -16,12 +20,13 @@ Sub-nodes: Sub-nodes required properties: - reg: the PHY number - phy-cells: generic PHY binding; must be 0 -Optional: -- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port +Sub-nodes optional properties: +- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port + This property is not applicable for "brcm,iproc-ns2-sata-phy" and + "brcm,iproc-nsp-sata-phy". Example: - sata-phy@f0458100 { compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 379b84a567cc..1d25b04cd05e 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -12,6 +12,16 @@ Required properties: - interrupts: Should contain phy interrupt - fsl,anatop: phandle for anatop register, it is only for imx6 SoC series +Optional properties: +- fsl,tx-cal-45-dn-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DN output signal. Default: 45 +- fsl,tx-cal-45-dp-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DP output signal. Default: 45 +- fsl,tx-d-cal: Integer [79-119]. Current trimming value (as a percentage) of + the 17.78mA TX reference current. Default: 100 + Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt new file mode 100644 index 000000000000..3742c152c467 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -0,0 +1,733 @@ +Device tree binding for NVIDIA Tegra XUSB pad controller +======================================================== + +The Tegra XUSB pad controller manages a set of I/O lanes (with differential +signals) which connect directly to pins/pads on the SoC package. Each lane +is controlled by a HW block referred to as a "pad" in the Tegra hardware +documentation. Each such "pad" may control either one or multiple lanes, +and thus contains any logic common to all its lanes. Each lane can be +separately configured and powered up. + +Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or +super-speed USB. Other lanes are for various types of low-speed, full-speed +or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller +contains a software-configurable mux that sits between the I/O controller +ports (e.g. PCIe) and the lanes. + +In addition to per-lane configuration, USB 3.0 ports may require additional +settings on a per-board basis. + +Pads will be represented as children of the top-level XUSB pad controller +device tree node. Each lane exposed by the pad will be represented by its +own subnode and can be referenced by users of the lane using the standard +PHY bindings, as described by the phy-bindings.txt file in this directory. + +The Tegra hardware documentation refers to the connection between the XUSB +pad controller and the XUSB controller as "ports". This is confusing since +"port" is typically used to denote the physical USB receptacle. The device +tree binding in this document uses the term "port" to refer to the logical +abstraction of the signals that are routed to a USB receptacle (i.e. a PHY +for the USB signal, the VBUS power supply, the USB 2.0 companion port for +USB 3.0 receptacles, ...). + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb-padctl" + - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl" + - Tegra210: "nvidia,tegra210-xusb-padctl" +- reg: Physical base address and length of the controller's registers. +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must include the following entries: + - "padctl" + + +Pad nodes: +========== + +A required child node named "pads" contains a list of subnodes, one for each +of the pads exposed by the XUSB pad controller. Each pad may need additional +resources that can be referenced in its pad node. + +The "status" property is used to enable or disable the use of a pad. If set +to "disabled", the pad will not be used on the given board. In order to use +the pad and any of its lanes, this property must be set to "okay". + +For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie +and sata. No extra resources are required for operation of these pads. + +For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is +a description of the properties of each pad. + +UTMI pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the USB2 tracking clock + +HSIC pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the HSIC tracking clock + +PCIe pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "pll": phandle and specifier referring to the PLLE +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the PCIe UPHY block + +SATA pad: +--------- + +Required properties: +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the SATA UPHY block + + +PHY nodes: +========== + +Each pad node has a child named "lanes" that contains one or more children of +its own, each representing one of the lanes controlled by the pad. + +Required properties: +-------------------- +- status: Defines the operation status of the PHY. Valid values are: + - "disabled": the PHY is disabled + - "okay": the PHY is enabled +- #phy-cells: Should be 0. Since each lane represents a single PHY, there is + no need for an additional specifier. +- nvidia,function: The output function of the PHY. See below for a list of + valid functions per SoC generation. + +For Tegra124 and Tegra132, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2 + - functions: "snps", "xusb", "uart" +- ulpi: ulpi-0 + - functions: "snps", "xusb" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4 + - functions: "pcie", "usb3-ss" +- sata: sata-0 + - functions: "usb3-ss", "sata" + +For Tegra210, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2, usb2-3 + - functions: "snps", "xusb", "uart" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6 + - functions: "pcie-x1", "usb3-ss", "pcie-x4" +- sata: sata-0 + - functions: "usb3-ss", "sata" + + +Port nodes: +=========== + +A required child node named "ports" contains a list of all the ports exposed +by the XUSB pad controller. Per-port configuration is only required for USB. + +USB2 ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- mode: A string that determines the mode in which to run the port. Valid + values are: + - "host": for USB host mode + - "device": for USB device mode + - "otg": for USB OTG mode + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +ULPI ports: +----------- + +Optional properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +HSIC ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled + +Optional properties: +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +Super-speed USB ports: +---------------------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,usb2-companion: A single cell that specifies the physical port number + to map this super-speed USB port to. The range of valid port numbers varies + with the SoC generation: + - 0-2: for Tegra124 and Tegra132 + - 0-3: for Tegra210 + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. + +For Tegra124 and Tegra132, the XUSB pad controller exposes the following +ports: +- 3x USB2: usb2-0, usb2-1, usb2-2 +- 1x ULPI: ulpi-0 +- 2x HSIC: hsic-0, hsic-1 +- 2x super-speed USB: usb3-0, usb3-1 + +For Tegra210, the XUSB pad controller exposes the following ports: +- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 +- 2x HSIC: hsic-0, hsic-1 +- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 + + +Examples: +========= + +Tegra124 and Tegra132: +---------------------- + +SoC include: + + padctl@7009f000 { + /* for Tegra124 */ + compatible = "nvidia,tegra124-xusb-padctl"; + /* for Tegra132 */ + compatible = "nvidia,tegra132-xusb-padctl", + "nvidia,tegra124-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + pads { + usb2 { + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + ulpi { + status = "disabled"; + + lanes { + ulpi-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + ulpi-0 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + /* Micro A/B */ + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + /* Mini PCIe */ + usb2-1 { + status = "okay"; + mode = "host"; + }; + + /* USB3 */ + usb2-2 { + status = "okay"; + mode = "host"; + + vbus-supply = <&vdd_usb3_vbus>; + }; + + usb3-0 { + nvidia,port = <2>; + status = "okay"; + }; + }; + }; + +Tegra210: +--------- + +SoC include: + + padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + status = "disabled"; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-5 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-6 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-3 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + status = "okay"; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + usb2-1 { + status = "okay"; + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + status = "okay"; + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + status = "okay"; + mode = "host"; + }; + + usb3-0 { + status = "okay"; + nvidia,lanes = "pcie-6"; + nvidia,port = <1>; + }; + + usb3-1 { + status = "okay"; + nvidia,lanes = "pcie-5"; + nvidia,port = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt new file mode 100644 index 000000000000..c26478be391b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -0,0 +1,40 @@ +TI DA8xx/OMAP-L1xx/AM18xx USB PHY + +Required properties: + - compatible: must be "ti,da830-usb-phy". + - #phy-cells: must be 1. + +This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG +controllers on DA8xx SoCs. Consumers of this device should use index 0 for +the USB 2.0 phy device and index 1 for the USB 1.1 phy device. + +It also requires a "syscon" node with compatible = "ti,da830-cfgchip", "syscon" +to access the CFGCHIP2 register. + +Example: + + cfgchip: cfgchip@1417c { + compatible = "ti,da830-cfgchip", "syscon"; + reg = <0x1417c 0x14>; + }; + + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <1>; + }; + + usb20: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x200000 0x1000>; + interrupts = <58>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + }; + + usb11: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt index bd61b467e30a..3bb821cd6a7f 100644 --- a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt +++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt @@ -18,7 +18,7 @@ creg: syscon@40043000 { compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; reg = <0x40043000 0x1000>; - usb0_otg_phy: phy@004 { + usb0_otg_phy: phy { compatible = "nxp,lpc1850-usb-otg-phy"; clocks = <&ccu1 CLK_USB0>; #phy-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt index 00100cf3e037..33a2b1ee3f3e 100644 --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -4,7 +4,9 @@ mt65xx USB3.0 PHY binding This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. Required properties (controller (parent) node): - - compatible : should be "mediatek,mt8173-u3phy" + - compatible : should be one of + "mediatek,mt2701-u3phy" + "mediatek,mt8173-u3phy" - reg : offset and length of register for phy, exclude port's register. - clocks : a list of phandle + clock-specifier pairs, one for each diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new file mode 100644 index 000000000000..3c29c77a7018 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -0,0 +1,64 @@ +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK + +Required properties (phy (parent) node): + - compatible : should be one of the listed compatibles: + * "rockchip,rk3366-usb2phy" + * "rockchip,rk3399-usb2phy" + - reg : the address offset of grf for usb-phy configuration. + - #clock-cells : should be 0. + - clock-output-names : specify the 480m output clock name. + +Optional properties: + - clocks : phandle + phy specifier pair, for the input clock of phy. + - clock-names : input clock name of phy, must be "phyclk". + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify host or otg port, + and shall be the following entries: + * "otg-port" : the name of otg port. + * "host-port" : the name of host port. + +Required properties (port (child) node): + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + - interrupts : specify an interrupt for each entry in interrupt-names. + - interrupt-names : a list which shall be the following entries: + * "otg-id" : for the otg id interrupt. + * "otg-bvalid" : for the otg vbus interrupt. + * "linestate" : for the host/otg linestate interrupt. + +Optional properties: + - phy-supply : phandle to a regulator that provides power to VBUS. + See ./phy-bindings.txt for details. + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + u2phy: usb2-phy@700 { + compatible = "rockchip,rk3366-usb2phy"; + reg = <0x700 0x2c>; + #clock-cells = <0>; + clock-output-names = "sclk_otgphy0_480m"; + + u2phy_otg: otg-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "otg-id", "otg-bvalid", "linestate"; + status = "okay"; + }; + + u2phy_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "linestate"; + status = "okay"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt new file mode 100644 index 000000000000..6ea867e3176f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt @@ -0,0 +1,101 @@ +* ROCKCHIP type-c PHY +--------------------- + +Required properties: + - compatible : must be "rockchip,rk3399-typec-phy" + - reg: Address and length of the usb phy control register set + - rockchip,grf : phandle to the syscon managing the "general + register files" + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref"; + - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or + <&cru SCLK_UPHY1_TCPDCORE>; + - assigned-clock-rates : the phy core clk frequency, shall be: 50000000 + - resets : a list of phandle + reset specifier pairs + - reset-names : string reset name, must be: + "uphy", "uphy-pipe", "uphy-tcphy" + - extcon : extcon specifier for the Power Delivery + +Note, there are 2 type-c phys for RK3399, and they are almost identical, except +these registers(description below), every register node contains 3 sections: +offset, enable bit, write mask bit. + - rockchip,typec-conn-dir : the register of type-c connector direction, + for type-c phy0, it must be <0xe580 0 16>; + for type-c phy1, it must be <0xe58c 0 16>; + - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable + control. + for type-c phy0, it must be <0xe580 3 19>; + for type-c phy1, it must be <0xe58c 3 19>; + - rockchip,external-psm : the register of type-c phy external psm clock + selection. + for type-c phy0, it must be <0xe588 14 30>; + for type-c phy1, it must be <0xe594 14 30>; + - rockchip,pipe-status : the register of type-c phy pipe status. + for type-c phy0, it must be <0xe5c0 0 0>; + for type-c phy1, it must be <0xe5c0 16 16>; + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify dp or usb3 port, + and shall be the following entries: + * "dp-port" : the name of DP port. + * "usb3-port" : the name of USB3 port. + +Required properties (port (child) node): +- #phy-cells : must be 0, See ./phy-bindings.txt for details. + +Example: + tcphy0: phy@ff7c0000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff7c0000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb0>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY0>, + <&cru SRST_UPHY0_PIPE_L00>, + <&cru SRST_P_UPHY0_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe580 0 16>; + rockchip,usb3tousb2-en = <0xe580 3 19>; + rockchip,external-psm = <0xe588 14 30>; + rockchip,pipe-status = <0xe5c0 0 0>; + + tcphy0_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy0_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + tcphy1: phy@ff800000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff800000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb1>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY1>, + <&cru SRST_UPHY1_PIPE_L00>, + <&cru SRST_P_UPHY1_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe58c 0 16>; + rockchip,usb3tousb2-en = <0xe58c 3 19>; + rockchip,external-psm = <0xe594 14 30>; + rockchip,pipe-status = <0xe5c0 16 16>; + + tcphy1_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy1_usb3: usb3-port { + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt index 00944a05ee6b..744b4809542e 100644 --- a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt @@ -17,7 +17,7 @@ Example: usb2_phy: usb2phy@0 { compatible = "st,stih416-usb-phy"; - #phy-cell = <0>; + #phy-cells = <0>; st,syscfg = <&syscfg_rear>; clocks = <&clk_sysin>; clock-names = "osc_phy"; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index d564ba4f1cf6..91da947ae9b6 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -7,6 +7,12 @@ Required properties: - compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the register block. - #address-cells: number of address cells for the USB channel subnodes, must be <1>. @@ -34,7 +40,7 @@ the USB channel; see the selector meanings below: Example (Lager board): usb-phy@e6590100 { - compatible = "renesas,usb-phy-r8a7790"; + compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy"; reg = <0 0xe6590100 0 0x100>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index eaf7e9b7ce6b..ace9cce2704a 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -6,6 +6,14 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. + "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 + SoC. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the partial USB 2.0 Host register block. - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. @@ -15,18 +23,20 @@ To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are combined, the device tree node should set interrupt properties to use the channel as USB OTG: - interrupts: interrupt specifier for the PHY. +- vbus-supply: Phandle to a regulator that provides power to the VBUS. This + regulator will be managed during the PHY power on/off sequence. Example (R-Car H3): usb-phy@ee080200 { - compatible = "renesas,usb2-phy-r8a7795"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + clocks = <&cpg CPG_MOD 703>; }; usb-phy@ee0a0200 { - compatible = "renesas,usb2-phy-r8a7795"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee0a0200 0 0x700>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + clocks = <&cpg CPG_MOD 702>; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt index 555cb0f40690..e3ea55763b0a 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -7,6 +7,13 @@ Required properties: - reg: PHY register address offset and length in "general register files" +Optional clocks using the clock bindings (see ../clock/clock-bindings.txt), +specified by name: + - clock-names: Should contain "emmcclk". Although this is listed as optional + (because most boards can get basic functionality without having + access to it), it is strongly suggested. + - clocks: Should have a phandle to the card clock exported by the SDHCI driver. + Example: @@ -20,6 +27,8 @@ grf: syscon@ff770000 { emmcphy: phy@f780 { compatible = "rockchip,rk3399-emmc-phy"; reg = <0xf780 0x20>; + clocks = <&sdhci>; + clock-names = "emmcclk"; #phy-cells = <0>; }; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt new file mode 100644 index 000000000000..0f6222a672ce --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt @@ -0,0 +1,31 @@ +Rockchip PCIE PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-pcie-phy + - #phy-cells: must be 0 + - clocks: Must contain an entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must be "refclk" + - resets: Must contain an entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must be "phy" + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + + ... + + pcie_phy: pcie-phy { + compatible = "rockchip,rk3399-pcie-phy"; + #phy-cells = <0>; + clocks = <&cru SCLK_PCIEPHY_REF>; + clock-names = "refclk"; + resets = <&cru SRST_PCIEPHY>; + reset-names = "phy"; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index 68498d560354..57dc388e2fa2 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -5,11 +5,13 @@ Required properties: "rockchip,rk3066a-usb-phy" "rockchip,rk3188-usb-phy" "rockchip,rk3288-usb-phy" - - rockchip,grf : phandle to the syscon managing the "general - register files" - #address-cells: should be 1 - #size-cells: should be 0 +Deprecated properties: + - rockchip,grf : phandle to the syscon managing the "general + register files" - phy should be a child of the GRF instead + Sub-nodes: Each PHY should be represented as a sub-node. @@ -25,17 +27,25 @@ Optional Properties: - clocks : phandle + clock specifier for the phy clocks - clock-names: string, clock name, must be "phyclk" - #clock-cells: for users of the phy-pll, should be 0 +- reset-names: Only allow the following entries: + - phy-reset +- resets: Must contain an entry for each entry in reset-names. Example: -usbphy: phy { - compatible = "rockchip,rk3288-usb-phy"; - rockchip,grf = <&grf>; - #address-cells = <1>; - #size-cells = <0>; +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + #address-cells = <1>; + #size-cells = <0>; - usbphy0: usb-phy0 { - #phy-cells = <0>; - reg = <0x320>; + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + }; }; }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 0289d3b07853..9872ba8546bd 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -2,9 +2,20 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,s5pv210-mipi-video-phy"; +- compatible : should be one of the listed compatibles: + - "samsung,s5pv210-mipi-video-phy" + - "samsung,exynos5420-mipi-video-phy" + - "samsung,exynos5433-mipi-video-phy" - #phy-cells : from the generic phy bindings, must be 1; -- syscon - phandle to the PMU system controller; + +In case of s5pv210 and exynos5420 compatible PHYs: +- syscon - phandle to the PMU system controller + +In case of exynos5433 compatible PHY: + - samsung,pmu-syscon - phandle to the PMU system controller + - samsung,disp-sysreg - phandle to the DISP system registers controller + - samsung,cam0-sysreg - phandle to the CAM0 system registers controller + - samsung,cam1-sysreg - phandle to the CAM1 system registers controller For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in the PHY specifier identifies the PHY and its meaning is as follows: @@ -12,6 +23,9 @@ the PHY specifier identifies the PHY and its meaning is as follows: 1 - MIPI DSIM 0, 2 - MIPI CSIS 1, 3 - MIPI DSIM 1. +"samsung,exynos5420-mipi-video-phy" and "samsung,exynos5433-mipi-video-phy" +supports additional fifth PHY: + 4 - MIPI CSIS 2. Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 95736d77fbb7..287150db6db4 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -10,6 +10,7 @@ Required properties: * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy * allwinner,sun8i-h3-usb-phy + * allwinner,sun50i-a64-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index a3b394587874..cd13e6157088 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -31,6 +31,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on + DRA7x Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY in DRA7x - reg : Address and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 69617220c5d6..1685821eea41 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -23,6 +23,7 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun50i-a64-pinctrl" + "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt index e4277921f3e3..a73cbeb0f309 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt @@ -3,8 +3,22 @@ Broadcom iProc GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", - "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" + "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that + supports full-featured pinctrl and GPIO functions used in various iProc + based SoCs + + May contain an SoC-specific compatibility string to accommodate any + SoC-specific features + + "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or + "brcm,cygnus-crmu-gpio" for Cygnus SoCs + + "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support + disabled + + "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general + pinctrl support completely disabled in this IP block. In Stingray, a + different IP block is used to handle pinctrl related functions - reg: Define the base and range of the I/O address space that contains SoC diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt new file mode 100644 index 000000000000..603564e5fe6f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt @@ -0,0 +1,79 @@ +Broadcom NSP (Northstar plus) IOMUX Controller + +The NSP IOMUX controller supports group based mux configuration. In +addition, certain pins can be muxed to GPIO function individually. + +Required properties: +- compatible: + Must be "brcm,nsp-pinmux" + +- reg: + Should contain the register physical address and length for each of + GPIO_CONTROL0, GP_AUX_SEL and IPROC_CONFIG IOMUX registers + +Properties in subnodes: +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinmux: pinmux@1803f1c0 { + compatible = "brcm,nsp-pinmux"; + reg = <0x1803f1c0 0x04>, + <0x18030028 0x04>, + <0x1803f408 0x04>; + + pinctrl-names = "default"; + pinctrl-0 = <&pwm &gpio_b &nand_sel>; + + pwm: pwm { + function = "pwm"; + groups = "pwm0_grp", "pwm1_grp"; + }; + + gpio_b: gpio_b { + function = "gpio_b"; + groups = "gpio_b_0_grp", "gpio_b_1_grp"; + }; + + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + }; + +List of supported functions and groups in Northstar Plus: + +"spi": "spi_grp" + +"i2c": "i2c_grp" + +"mdio": "mdio_grp" + +"pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" + +"gpio_b": "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp", "gpio_b_3_grp" + +"uart1": "uart1_grp" + +"uart2": "uart2_grp" + +"synce": "synce_grp" + +"sata_led_grps": "sata0_led_grp", "sata1_led_grp" + +"xtal_out": "xtal_out_grp" + +"sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +"switch_led": "switch_p05_led0_grp", "switch_p05_led1_grp" + +"nand": "nand_grp" + +"emmc": "emmc_grp" diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 32f4a2d6d0b3..fe7fe0b03cfb 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -5,6 +5,8 @@ Required properties for the root node: "amlogic,meson8b-cbus-pinctrl" "amlogic,meson8-aobus-pinctrl" "amlogic,meson8b-aobus-pinctrl" + "amlogic,meson-gxbb-periphs-pinctrl" + "amlogic,meson-gxbb-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt index 4b5efa51bec7..29b72e303ebf 100644 --- a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -34,7 +34,7 @@ pic32_pinctrl: pinctrl@1f801400{ #size-cells = <1>; compatible = "microchip,pic32mzda-pinctrl"; reg = <0x1f801400 0x400>; - clocks = <&PBCLK1>; + clocks = <&rootclk PB1CLK>; pinctrl_uart2: pinctrl_uart2 { uart2-tx { diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt new file mode 100644 index 000000000000..f2abdaee9022 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt @@ -0,0 +1,60 @@ +Device tree binding for NVIDIA Tegra DPAUX pad controller +======================================================== + +The Tegra Display Port Auxiliary (DPAUX) pad controller manages two pins +which can be assigned to either the DPAUX channel or to an I2C +controller. + +This document defines the device-specific binding for the DPAUX pad +controller. Refer to pinctrl-bindings.txt in this directory for generic +information about pin controller device tree bindings. Please refer to +the binding document ../display/tegra/nvidia,tegra20-host1x.txt for more +details on the DPAUX binding. + +Pin muxing: +----------- + +Child nodes contain the pinmux configurations following the conventions +from the pinctrl-bindings.txt document. + +Since only three configurations are possible, only three child nodes are +needed to describe the pin mux'ing options for the DPAUX pads. +Furthermore, given that the pad functions are only applicable to a +single set of pads, the child nodes only need to describe the pad group +the functions are being applied to rather than the individual pads. + +Required properties: +- groups: Must be "dpaux-io" +- function: Must be either "aux", "i2c" or "off". + +Example: +-------- + + dpaux@545c0000 { + ... + + state_dpaux_aux: pinmux-aux { + groups = "dpaux-io"; + function = "aux"; + }; + + state_dpaux_i2c: pinmux-i2c { + groups = "dpaux-io"; + function = "i2c"; + }; + + state_dpaux_off: pinmux-off { + groups = "dpaux-io"; + function = "off"; + }; + }; + + ... + + i2c@7000d100 { + ... + pinctrl-0 = <&state_dpaux_i2c>; + pinctrl-1 = <&state_dpaux_off>; + pinctrl-names = "default", "idle"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt index 30676ded85bb..4048f43a9d29 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt @@ -1,6 +1,12 @@ Device tree binding for NVIDIA Tegra XUSB pad controller ======================================================== +NOTE: It turns out that this binding isn't an accurate description of the XUSB +pad controller. While the description is good enough for the functional subset +required for PCIe and SATA, it lacks the flexibility to represent the features +needed for USB. For the new binding, see ../phy/nvidia,tegra-xusb-padctl.txt. +The binding described in this file is deprecated and should not be used. + The Tegra XUSB pad controller manages a set of lanes, each of which can be assigned to one out of a set of different pads. Some of these pads have an associated PHY that must be powered up before the pad can be used. @@ -79,7 +85,7 @@ Example: SoC file extract: ----------------- - padctl@0,7009f000 { + padctl@7009f000 { compatible = "nvidia,tegra124-xusb-padctl"; reg = <0x0 0x7009f000 0x0 0x1000>; resets = <&tegra_car 142>; @@ -91,7 +97,7 @@ SoC file extract: Board file extract: ------------------- - pcie-controller@0,01003000 { + pcie-controller@01003000 { ... phys = <&padctl 0>; @@ -102,7 +108,7 @@ Board file extract: ... - padctl: padctl@0,7009f000 { + padctl: padctl@7009f000 { pinctrl-0 = <&padctl_default>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt new file mode 100644 index 000000000000..d6074321f730 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -0,0 +1,57 @@ +* Oxford Semiconductor OXNAS SoC Family Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +OXNAS 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configurations of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "oxsemi,ox810se-pinctrl" + - oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + +Example: + +pinctrl: pinctrl { + compatible = "oxsemi,ox810se-pinctrl"; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + pinctrl_uart2: pinctrl_uart2 { + uart2a { + pins = "gpio31"; + function = "fct3"; + }; + uart2b { + pins = "gpio32"; + function = "fct3"; + }; + }; +}; + +uart2: serial@900000 { + compatible = "ns16550a"; + reg = <0x900000 0x100000>; + clocks = <&sysclk>; + interrupts = <29>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + resets = <&reset 22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt new file mode 100644 index 000000000000..5e60ad18f147 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -0,0 +1,65 @@ +Aspeed Pin Controllers +---------------------- + +The Aspeed SoCs vary in functionality inside a generation but have a common mux +device register layout. + +Required properties: +- compatible : Should be any one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +The pin controller node should be a child of a syscon node with the required +property: +- compatible: "syscon", "simple-mfd" + +Refer to the the bindings described in +Documentation/devicetree/bindings/mfd/syscon.txt + +Subnode Format +-------------- + +The required properties of child nodes are (as defined in pinctrl-bindings): +- function +- groups + +Each function has only one associated pin group. Each group is named by its +function. The following values for the function and groups properties are +supported: + +aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: + +ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 +I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1 +MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3 +NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16 +ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30 +VPO12 VPO24 + +aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: + +GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 +I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 +RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 + +Examples: + +syscon: scu@1e6e2000 { + compatible = "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + }; +}; + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt new file mode 100644 index 000000000000..ad4fce3552bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt @@ -0,0 +1,127 @@ +Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7. + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + drive-push-pull, + drive-open-drain, + bias-pull-up, + bias-pull-down. + +Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in, + reference-out + +Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These +customised properties are required to configure FPS configuration parameters +of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more +detail of Flexible Power Sequence (FPS). + +- maxim,active-fps-source: FPS source for the GPIOs to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + GPIO is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + GPIO to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the GPIO get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the GPIO get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + + pinctrl-names = "default"; + pinctrl-0 = <&spmic_default>; + + spmic_default: pinmux@0 { + pin_gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + pin_gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + pin_gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt index 26bcb18f4e60..013c675b5b64 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt @@ -30,8 +30,7 @@ Second type has a dedicated interrupt per gpio bank. Pin controller node: Required properties: -- compatible : should be "st,<SOC>-<pio-block>-pinctrl" - like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. +- compatible : should be "st,stih407-<pio-block>-pinctrl" - st,syscfg : Should be a phandle of the syscfg node. - st,retime-pin-mask : Should be mask to specify which pins can be retimed. If the property is not present, it is assumed that all the pins in the @@ -50,7 +49,11 @@ Optional properties: GPIO controller/bank node. Required properties: - gpio-controller : Indicates this device is a GPIO controller -- #gpio-cells : Should be one. The first cell is the pin number. +- #gpio-cells : Must be two. + - First cell: specifies the pin number inside the controller + - Second cell: specifies whether the pin is logically inverted. + - 0 = active high + - 1 = active low - st,bank-name : Should be a name string for this bank as specified in datasheet. @@ -76,23 +79,23 @@ include/dt-bindings/interrupt-controller/irq.h Example: pin-controller-sbc { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stih415-sbc-pinctrl"; - st,syscfg = <&syscfg_sbc>; - reg = <0xfe61f080 0x4>; - reg-names = "irqmux"; - interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "irqmux"; - ranges = <0 0xfe610000 0x5000>; - - PIO0: gpio@fe610000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stih407-sbc-pinctrl"; + st,syscfg = <&syscfg_sbc>; + reg = <0x0961f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>; + interrupt-names = "irqmux"; + ranges = <0 0x09610000 0x6000>; + + pio0: gpio@09610000 { gpio-controller; - #gpio-cells = <1>; + #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - reg = <0 0x100>; - st,bank-name = "PIO0"; + reg = <0x0 0x100>; + st,bank-name = "PIO0"; }; ... pin-functions nodes follow... @@ -162,7 +165,7 @@ pin-controller { sdhci0:sdhci@fe810000{ ... - interrupt-parent = <&PIO3>; + interrupt-parent = <&pio3>; #interrupt-cells = <2>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */ interrupt-names = "card-detect"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt new file mode 100644 index 000000000000..1b52f01ddcb7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt @@ -0,0 +1,152 @@ +Qualcomm MDM9615 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MDM9615 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,mdm9615-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio87 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. + Valid values are: + gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart, + sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, + cdc_mclk + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,mdm9615-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + + gsbi8_uart: gsbi8-uart { + mux { + pins = "gpio34", "gpio35"; + function = "gsbi8"; + }; + + tx { + pins = "gpio34"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio35"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt index 77aa11790163..df9a838ec5f9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt @@ -52,7 +52,7 @@ Valid values for function are: gsbi2_spi_cs3_n, gsbi3, gsbi3_spi_cs1_n, gsbi3_spi_cs2_n, gsbi3_spi_cs3_n, gsbi4, gsbi5, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, gsbi11, gsbi12, hdmi, i2s, lcdc, mdp_vsync, mi2s, pcm, ps_hold, sdc1, sdc2, sdc5, tsif1, tsif2, usb_fs1, - usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, + usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs Example: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index e4d6a9d20f7d..453bd7c76d6b 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -49,6 +49,9 @@ Valid values for pins are: sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data Supports bias and drive-strength + hsic_data, hsic_strobe + Supports only mux + Valid values for function are: cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, @@ -70,7 +73,7 @@ Valid values for function are: cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, - ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio (Note that this is not yet the complete list of functions) diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index a90c812ad642..8d893a874634 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -17,6 +17,9 @@ PMIC's from Qualcomm. "qcom,pm8994-gpio" "qcom,pma8084-gpio" + And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" + if the device is on an spmi bus or an ssbi bus respectively + - reg: Usage: required Value type: <prop-encoded-array> @@ -122,7 +125,7 @@ to specify in a pin configuration subnode: 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5) 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5) 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30) - If this property is ommited 30uA strength will be used if + If this property is omitted 30uA strength will be used if pull up is selected - bias-high-impedance: @@ -183,7 +186,7 @@ to specify in a pin configuration subnode: Example: pm8921_gpio: gpio@150 { - compatible = "qcom,pm8921-gpio"; + compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio"; reg = <0x150 0x160>; interrupts = <192 1>, <193 1>, <194 1>, <195 1>, <196 1>, <197 1>, diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index d74e631e10da..2ab95bc26066 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -9,6 +9,7 @@ of PMIC's from Qualcomm. Definition: Should contain one of: "qcom,pm8018-mpp", "qcom,pm8038-mpp", + "qcom,pm8058-mpp", "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", @@ -18,6 +19,9 @@ of PMIC's from Qualcomm. "qcom,pm8994-mpp", "qcom,pma8084-mpp", + And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp" + if the device is on an spmi bus or an ssbi bus respectively. + - reg: Usage: required Value type: <prop-encoded-array> @@ -157,7 +161,7 @@ to specify in a pin configuration subnode: Example: mpps@a000 { - compatible = "qcom,pm8841-mpp"; + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp"; reg = <0xa000>; gpio-controller; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index ffadb7a371f6..13df9498311a 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -17,9 +17,11 @@ Required Properties: - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. + - "renesas,pfc-r8a7792": for R8A7792 (R-Car V2H) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. + - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin @@ -72,8 +74,8 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that -have a configurable I/O voltage, the power-source value should be the +bias-disable, bias-pull-up, bias-pull-down, drive-strength and power-source. For +pins that have a configurable I/O voltage, the power-source value should be the nominal I/O voltage in millivolts. diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 7b4800cc251e..f9753c416974 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -9,10 +9,16 @@ Pin controller node: Required properies: - compatible: value should be one of the following: (a) "st,stm32f429-pinctrl" + (b) "st,stm32f746-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to gpio-bank node (children). + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node + which includes IRQ mux selection register, and the offset of the IRQ mux + selection register. - pins-are-numbered: Specify the subnodes are using numbered pinmux to specify pins. diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt b/Documentation/devicetree/bindings/power/act8945a-charger.txt deleted file mode 100644 index bea254c9d136..000000000000 --- a/Documentation/devicetree/bindings/power/act8945a-charger.txt +++ /dev/null @@ -1,35 +0,0 @@ -Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device - -Required properties: - - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. - - active-semi,chglev-gpios: charge current level phandle with args - as described in ../gpio/gpio.txt. - -Optional properties: - - active-semi,check-battery-temperature: boolean to check the battery - temperature or not. - - active-semi,input-voltage-threshold-microvolt: unit: mV; - Specifies the charger's input over-voltage threshold value; - The value can be: 6600, 7000, 7500, 8000; default: 6600 - - active-semi,precondition-timeout: unit: minutes; - Specifies the charger's PRECONDITION safety timer setting value; - The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; - default: 40. - - active-semi,total-timeout: unit: hours; - Specifies the charger's total safety timer setting value; - The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; - default: 3. - -Example: - pmic@5b { - compatible = "active-semi,act8945a"; - reg = <0x5b>; - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_chglev>; - active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; - active-semi,input-voltage-threshold-microvolt = <6600>; - active-semi,precondition-timeout = <40>; - active-semi,total-timeout = <3>; - }; diff --git a/Documentation/devicetree/bindings/power/max8903-charger.txt b/Documentation/devicetree/bindings/power/max8903-charger.txt new file mode 100644 index 000000000000..f0f4e12b076e --- /dev/null +++ b/Documentation/devicetree/bindings/power/max8903-charger.txt @@ -0,0 +1,25 @@ +Maxim Semiconductor MAX8903 Battery Charger bindings + +Required properties: +- compatible: "maxim,max8903" for MAX8903 Battery Charger +- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided +- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided + +Optional properties: +- cen-gpios: Charge enable pin (active low, output) +- chg-gpios: Charger status pin (active low, input) +- flt-gpios: Fault pin (active low, output) +- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) +- usus-gpios: USB suspend pin (active high, output) + + +Example: + + max8903-charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt new file mode 100644 index 000000000000..84404c9edff7 --- /dev/null +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -0,0 +1,31 @@ +DT bindings for the Renesas Advanced Power Management Unit + +Renesas R-Car line of SoCs utilize one or more APMU hardware units +for CPU core power domain control including SMP boot and CPU Hotplug. + +Required properties: + +- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. + Examples with soctypes are: + - "renesas,r8a7790-apmu" (R-Car H2) + - "renesas,r8a7791-apmu" (R-Car M2-W) + - "renesas,r8a7792-apmu" (R-Car V2H) + - "renesas,r8a7793-apmu" (R-Car M2-N) + - "renesas,r8a7794-apmu" (R-Car E2) + +- reg: Base address and length of the I/O registers used by the APMU. + +- cpus: This node contains a list of CPU cores, which should match the order + of CPU cores used by the WUPCR and PSTR registers in the Advanced Power + Management Unit section of the device's datasheet. + + +Example: + +This shows the r8a7791 APMU that can control CPU0 and CPU1. + + apmu@e6152000 { + compatible = "renesas,r8a7791-apmu", "renesas,apmu"; + reg = <0 0xe6152000 0 0x188>; + cpus = <&cpu0 &cpu1>; + }; diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt new file mode 100644 index 000000000000..0725fb37a973 --- /dev/null +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -0,0 +1,49 @@ +DT bindings for the Renesas R-Car System Controller + +== System Controller Node == + +The R-Car System Controller provides power management for the CPU cores and +various coprocessors. + +Required properties: + - compatible: Must contain exactly one of the following: + - "renesas,r8a7779-sysc" (R-Car H1) + - "renesas,r8a7790-sysc" (R-Car H2) + - "renesas,r8a7791-sysc" (R-Car M2-W) + - "renesas,r8a7792-sysc" (R-Car V2H) + - "renesas,r8a7793-sysc" (R-Car M2-N) + - "renesas,r8a7794-sysc" (R-Car E2) + - "renesas,r8a7795-sysc" (R-Car H3) + - "renesas,r8a7796-sysc" (R-Car M3-W) + - reg: Address start and address range for the device. + - #power-domain-cells: Must be 1. + + +Example: + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a7791-sysc"; + reg = <0 0xe6180000 0 0x0200>; + #power-domain-cells = <1>; + }; + + +== PM Domain Consumers == + +Devices residing in a power area must refer to that power area, as documented +by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + +Required properties: + - power-domains: A phandle and symbolic PM domain specifier, as defined in + <dt-bindings/power/r8a77*-sysc.h>. + + +Example: + + L2_CA15: cache-controller@0 { + compatible = "cache"; + power-domains = <&sysc R8A7791_PD_CA15_SCU>; + cache-unified; + cache-level = <2>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/axxia-reset.txt b/Documentation/devicetree/bindings/power/reset/axxia-reset.txt index 47e720d249d2..47e720d249d2 100644 --- a/Documentation/devicetree/bindings/power_supply/axxia-reset.txt +++ b/Documentation/devicetree/bindings/power/reset/axxia-reset.txt diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm21664-resetmgr.txt b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt index 93f31ca1ef4b..93f31ca1ef4b 100644 --- a/Documentation/devicetree/bindings/reset/brcm,bcm21664-resetmgr.txt +++ b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt index d4eab9227ea4..d4eab9227ea4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt index af3701bc15c4..af3701bc15c4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-restart.txt +++ b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt diff --git a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt index dc7c9bad63ea..dc7c9bad63ea 100644 --- a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt diff --git a/Documentation/devicetree/bindings/power_supply/msm-poweroff.txt b/Documentation/devicetree/bindings/power/reset/msm-poweroff.txt index ce44ad357565..ce44ad357565 100644 --- a/Documentation/devicetree/bindings/power_supply/msm-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/msm-poweroff.txt diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt index af25e77c0e0c..af25e77c0e0c 100644 --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt diff --git a/Documentation/devicetree/bindings/power/reset/reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt new file mode 100644 index 000000000000..de34f27d509e --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt @@ -0,0 +1,25 @@ +Generic reboot mode core map driver + +This driver get reboot mode arguments and call the write +interface to store the magic value in special register +or ram. Then the bootloader can read it and take different +action according to the argument stored. + +All mode properties are vendor specific, it is a indication to tell +the bootloader what to do when the system reboots, and should be named +as mode-xxx = <magic> (xxx is mode name, magic should be a none-zero value). + +For example modes common on Android platform: +- mode-normal: Normal reboot mode, system reboot with command "reboot". +- mode-recovery: Android Recovery mode, it is a mode to format the device or update a new image. +- mode-bootloader: Android fastboot mode, it's a mode to re-flash partitions on the Android based device. +- mode-loader: A bootloader mode, it's a mode used to download image on Rockchip platform, + usually used in development. + +Example: + reboot-mode { + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + } diff --git a/Documentation/devicetree/bindings/power_supply/restart-poweroff.txt b/Documentation/devicetree/bindings/power/reset/restart-poweroff.txt index 5776e684afda..5776e684afda 100644 --- a/Documentation/devicetree/bindings/power_supply/restart-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/restart-poweroff.txt diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt index 809af54f02f3..83734dc3a389 100644 --- a/Documentation/devicetree/bindings/power/reset/st-reset.txt +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -1,11 +1,12 @@ *Device-Tree bindings for ST SW reset functionality Required properties: -- compatible: should be "st,<chip>-restart". +- compatible: should be "stih407-restart". - st,syscfg: should be a phandle of the syscfg node. Example node: restart { - compatible = "st,stih416-restart"; - st,syscfg = <&syscfg_sbc>; + compatible = "st,stih407-restart"; + st,syscfg = <&syscfg_sbc_reg>; + status = "okay"; }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt new file mode 100644 index 000000000000..f7ce1d8af04a --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt @@ -0,0 +1,35 @@ +SYSCON reboot mode driver + +This driver gets reboot mode magic value form reboot-mode driver +and stores it in a SYSCON mapped register. Then the bootloader +can read it and take different action according to the magic +value stored. + +This DT node should be represented as a sub-node of a "syscon", "simple-mfd" +node. + +Required properties: +- compatible: should be "syscon-reboot-mode" +- offset: offset in the register map for the storage register (in bytes) + +Optional property: +- mask: bits mask of the bits in the register to store the reboot mode magic value, + default set to 0xffffffff if missing. + +The rest of the properties should follow the generic reboot-mode description +found in reboot-mode.txt + +Example: + pmu: pmu@20004000 { + compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd"; + reg = <0x20004000 0x100>; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x40>; + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + }; + }; diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt index 0ba1bcc7f33a..0ba1bcc7f33a 100644 --- a/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt index ef5328371122..ef5328371122 100644 --- a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt index 6bdbb08ea9e0..6bdbb08ea9e0 100644 --- a/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt index ccafcb9112fb..ccafcb9112fb 100644 --- a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt +++ b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt new file mode 100644 index 000000000000..de78d761ce44 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -0,0 +1,48 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a-charger". + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. + - interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt index 862f4a49dc49..f1d7beec45bf 100644 --- a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -1,7 +1,8 @@ AXP20x USB power supply Required Properties: --compatible: "x-powers,axp202-usb-power-supply" +-compatible: One of: "x-powers,axp202-usb-power-supply" + "x-powers,axp221-usb-power-supply" This node is a subnode of the axp20x PMIC. diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt index d0327f0b59ad..d0327f0b59ad 100644 --- a/Documentation/devicetree/bindings/power/bq2415x.txt +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.txt diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt index d693702c9c1e..d693702c9c1e 100644 --- a/Documentation/devicetree/bindings/power/bq24257.txt +++ b/Documentation/devicetree/bindings/power/supply/bq24257.txt diff --git a/Documentation/devicetree/bindings/power/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt index c9dd17d142ad..c9dd17d142ad 100644 --- a/Documentation/devicetree/bindings/power/bq25890.txt +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt diff --git a/Documentation/devicetree/bindings/power_supply/charger-manager.txt b/Documentation/devicetree/bindings/power/supply/charger-manager.txt index ec4fe9de3137..ec4fe9de3137 100644 --- a/Documentation/devicetree/bindings/power_supply/charger-manager.txt +++ b/Documentation/devicetree/bindings/power/supply/charger-manager.txt diff --git a/Documentation/devicetree/bindings/power/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt index f3906663c454..f3906663c454 100644 --- a/Documentation/devicetree/bindings/power/da9150-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt diff --git a/Documentation/devicetree/bindings/power/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt index 00236fe3ea31..00236fe3ea31 100644 --- a/Documentation/devicetree/bindings/power/da9150-fg.txt +++ b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/gpio-charger.txt b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt index adbb5dc5b6e9..adbb5dc5b6e9 100644 --- a/Documentation/devicetree/bindings/power_supply/gpio-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt diff --git a/Documentation/devicetree/bindings/power/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt index fa3596907967..fa3596907967 100644 --- a/Documentation/devicetree/bindings/power/isp1704.txt +++ b/Documentation/devicetree/bindings/power/supply/isp1704.txt diff --git a/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt index 2246bc5c874b..2246bc5c874b 100644 --- a/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt diff --git a/Documentation/devicetree/bindings/power/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt index ea42ae12d924..ea42ae12d924 100644 --- a/Documentation/devicetree/bindings/power/ltc2941.txt +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt diff --git a/Documentation/devicetree/bindings/power_supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt index 3f3894aaeebc..3f3894aaeebc 100644 --- a/Documentation/devicetree/bindings/power_supply/max17042_battery.txt +++ b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt diff --git a/Documentation/devicetree/bindings/power_supply/max8925_batter.txt b/Documentation/devicetree/bindings/power/supply/max8925_batter.txt index d7e3e0c0f71d..d7e3e0c0f71d 100644 --- a/Documentation/devicetree/bindings/power_supply/max8925_batter.txt +++ b/Documentation/devicetree/bindings/power/supply/max8925_batter.txt diff --git a/Documentation/devicetree/bindings/power_supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt index c8901b3992d9..c8901b3992d9 100644 --- a/Documentation/devicetree/bindings/power_supply/olpc_battery.txt +++ b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt diff --git a/Documentation/devicetree/bindings/power_supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt index 8391bfa0edac..8391bfa0edac 100644 --- a/Documentation/devicetree/bindings/power_supply/power_supply.txt +++ b/Documentation/devicetree/bindings/power/supply/power_supply.txt diff --git a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt index 0e6d8754e7ec..747899223262 100644 --- a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt @@ -29,7 +29,7 @@ IC (PMIC) - qcom,charger-disable: Usage: optional Value type: <boolean> - Definition: definining this property disables charging + Definition: defining this property disables charging This charger is a sub-node of one of the 8941 PMIC blocks, and is specified as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt index 65b88fac854b..65b88fac854b 100644 --- a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt diff --git a/Documentation/devicetree/bindings/power/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt index 5d9ad5cf2c5a..5d9ad5cf2c5a 100644 --- a/Documentation/devicetree/bindings/power/rt9455_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt diff --git a/Documentation/devicetree/bindings/power/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt index 90438453db58..90438453db58 100644 --- a/Documentation/devicetree/bindings/power/rx51-battery.txt +++ b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt diff --git a/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt index c40e8926facf..c40e8926facf 100644 --- a/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt diff --git a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt index 3bf55757ceec..3bf55757ceec 100644 --- a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt diff --git a/Documentation/devicetree/bindings/power_supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt index 8e5e0d3910df..8e5e0d3910df 100644 --- a/Documentation/devicetree/bindings/power_supply/tps65090.txt +++ b/Documentation/devicetree/bindings/power/supply/tps65090.txt diff --git a/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt index 98d131acee95..98d131acee95 100644 --- a/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt index 3b4ea1b73b38..3b4ea1b73b38 100644 --- a/Documentation/devicetree/bindings/power/twl-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/twl-charger.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt deleted file mode 100644 index 29b28b8f9a89..000000000000 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt +++ /dev/null @@ -1,43 +0,0 @@ -* Network - -Currently defined compatibles: -- fsl,cpm1-scc-enet -- fsl,cpm2-scc-enet -- fsl,cpm1-fec-enet -- fsl,cpm2-fcc-enet (third resource is GFEMR) -- fsl,qe-enet - -Example: - - ethernet@11300 { - compatible = "fsl,mpc8272-fcc-enet", - "fsl,cpm2-fcc-enet"; - reg = <11300 20 8400 100 11390 1>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <20 8>; - interrupt-parent = <&PIC>; - phy-handle = <&PHY0>; - fsl,cpm-command = <12000300>; - }; - -* MDIO - -Currently defined compatibles: -fsl,pq1-fec-mdio (reg is same as first resource of FEC device) -fsl,cpm2-mdio-bitbang (reg is port C registers) - -Properties for fsl,cpm2-mdio-bitbang: -fsl,mdio-pin : pin of port C controlling mdio data -fsl,mdc-pin : pin of port C controlling mdio clock - -Example: - mdio@10d40 { - compatible = "fsl,mpc8272ads-mdio-bitbang", - "fsl,mpc8272-mdio-bitbang", - "fsl,cpm2-mdio-bitbang"; - reg = <10d40 14>; - #address-cells = <1>; - #size-cells = <0>; - fsl,mdio-pin = <12>; - fsl,mdc-pin = <13>; - }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt index 55c2c03fc81e..df873d1f3b7c 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt @@ -35,7 +35,7 @@ PROPERTIES Definition: Specifies the index of the FMan unit. The cell-index value may be used by the SoC, to identify the - FMan unit in the SoC memory map. In the table bellow, + FMan unit in the SoC memory map. In the table below, there's a description of the cell-index use in each SoC: - P1023: @@ -247,7 +247,7 @@ PROPERTIES The cell-index value may be used by the FMan or the SoC, to identify the MAC unit in the FMan (or SoC) memory map. - In the tables bellow there's a description of the cell-index + In the tables below there's a description of the cell-index use, there are two tables, one describes the use of cell-index by the FMan, the second describes the use by the SoC: diff --git a/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt b/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt new file mode 100644 index 000000000000..dffb79108b61 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt @@ -0,0 +1,14 @@ +IBM OPAL Operator Panel Binding +------------------------------- + +Required properties: +- compatible : Should be "ibm,opal-oppanel". +- #lines : Number of lines on the operator panel e.g. <0x2>. +- #length : Number of characters per line of the operator panel e.g. <0x10>. + +Example: + oppanel { + compatible = "ibm,opal-oppanel"; + #lines = <0x2>; + #length = <0x10>; + }; diff --git a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt new file mode 100644 index 000000000000..21f75bbd6dae --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt @@ -0,0 +1,21 @@ +Broadcom iProc PWM controller device tree bindings + +This controller has 4 channels. + +Required Properties : +- compatible: must be "brcm,iproc-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@18031000 { + compatible = "brcm,iproc-pwm"; + reg = <0x18031000 0x28>; + clocks = <&osc>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt index a183db48f910..c0b2028238d6 100644 --- a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -1,15 +1,14 @@ * Cirris Logic CLPS711X PWM controller Required properties: -- compatible: Shall contain "cirrus,clps711x-pwm". +- compatible: Shall contain "cirrus,ep7209-pwm". - reg: Physical base address and length of the controller's registers. - clocks: phandle + clock specifier pair of the PWM reference clock. - #pwm-cells: Should be 1. The cell specifies the index of the channel. Example: pwm: pwm@80000400 { - compatible = "cirrus,ep7312-pwm", - "cirrus,clps711x-pwm"; + compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm"; reg = <0x80000400 0x4>; clocks = <&clks 8>; #pwm-cells = <1>; diff --git a/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt b/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt new file mode 100644 index 000000000000..472bd46ab5a4 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt @@ -0,0 +1,23 @@ +* PWM controlled by ChromeOS EC + +Google's ChromeOS EC PWM is a simple PWM attached to the Embedded Controller +(EC) and controlled via a host-command interface. + +An EC PWM node should be only found as a sub-node of the EC node (see +Documentation/devicetree/bindings/mfd/cros-ec.txt). + +Required properties: +- compatible: Must contain "google,cros-ec-pwm" +- #pwm-cells: Should be 1. The cell specifies the PWM index. + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt index c52f03b5032f..b4e73778dda3 100644 --- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -1,10 +1,14 @@ Tegra SoC PWFM controller Required properties: -- compatible: For Tegra20, must contain "nvidia,tegra20-pwm". For Tegra30, - must contain "nvidia,tegra30-pwm". Otherwise, must contain - "nvidia,<chip>-pwm", plus one of the above, where <chip> is tegra114, - tegra124, tegra132, or tegra210. +- compatible: Must be: + - "nvidia,tegra20-pwm": for Tegra20 + - "nvidia,tegra30-pwm", "nvidia,tegra20-pwm": for Tegra30 + - "nvidia,tegra114-pwm", "nvidia,tegra20-pwm": for Tegra114 + - "nvidia,tegra124-pwm", "nvidia,tegra20-pwm": for Tegra124 + - "nvidia,tegra132-pwm", "nvidia,tegra20-pwm": for Tegra132 + - "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210 + - "nvidia,tegra186-pwm": for Tegra186 - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt index 5befb538db95..2e53324fb720 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt @@ -9,6 +9,10 @@ Required properties: Optional properties: - ti,prescaler: Should be a value between 0 and 7, see the timers datasheet +- ti,clock-source: Set dmtimer parent clock, values between 0 and 2: + - 0x00 - high-frequency system clock (timer_sys_ck) + - 0x01 - 32-kHz always-on clock (timer_32k_ck) + - 0x02 - external clock (timer_ext_ck, OMAP2 only) Example: pwm9: dmtimer-pwm@9 { diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt index fb81179dce37..8007e839a716 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -2,28 +2,48 @@ TI SOC ECAP based APWM controller Required properties: - compatible: Must be "ti,<soc>-ecap". - for am33xx - compatible = "ti,am33xx-ecap"; - for da850 - compatible = "ti,da850-ecap", "ti,am33xx-ecap"; + for am33xx - compatible = "ti,am3352-ecap", "ti,am33xx-ecap"; + for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + for da850 - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap"; - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. The PWM channel index ranges from 0 to 4. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map. Optional properties: -- ti,hwmods: Name of the hwmod associated to the ECAP: - "ecap<x>", <x> being the 0-based instance number from the HW spec +- clocks: Handle to the ECAP's functional clock. +- clock-names: Must be set to "fck". Example: -ecap0: ecap@0 { /* ECAP on am33xx */ - compatible = "ti,am33xx-ecap"; +ecap0: ecap@48300100 { /* ECAP on am33xx */ + compatible = "ti,am3352-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "fck"; +}; + +ecap0: ecap@48300100 { /* ECAP on am4372 */ + compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48300100 0x80>; ti,hwmods = "ecap0"; + clocks = <&l4ls_gclk>; + clock-names = "fck"; +}; + +ecap0: ecap@1f06000 { /* ECAP on da850 */ + compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x1f06000 0x80>; }; -ecap0: ecap@0 { /* ECAP on da850 */ - compatible = "ti,da850-ecap", "ti,am33xx-ecap"; +ecap0: ecap@4843e100 { + compatible = "ti,dra746-ecap", "ti,am3352-ecap"; #pwm-cells = <3>; - reg = <0x306000 0x80>; + reg = <0x4843e100 0x80>; + clocks = <&l4_root_clk_div>; + clock-names = "fck"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt index 9c100b2c5b23..944fe356bb45 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -2,28 +2,48 @@ TI SOC EHRPWM based PWM controller Required properties: - compatible: Must be "ti,<soc>-ehrpwm". - for am33xx - compatible = "ti,am33xx-ehrpwm"; - for da850 - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; + for am33xx - compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for am4372 - compatible = "ti,am4372-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm"; - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map. Optional properties: -- ti,hwmods: Name of the hwmod associated to the EHRPWM: - "ehrpwm<x>", <x> being the 0-based instance number from the HW spec +- clocks: Handle to the PWM's time-base and functional clock. +- clock-names: Must be set to "tbclk" and "fck". Example: -ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */ - compatible = "ti,am33xx-ehrpwm"; +ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */ + compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; #pwm-cells = <3>; reg = <0x48300200 0x100>; + clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; + clock-names = "tbclk", "fck"; +}; + +ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */ + compatible = "ti,am4372-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x80>; + clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; + clock-names = "tbclk", "fck"; ti,hwmods = "ehrpwm0"; }; -ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */ - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; +ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */ + compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x1f00000 0x2000>; +}; + +ehrpwm0: pwm@4843e200 { /* EHRPWM on dra746 */ + compatible = "ti,dra746-ehrpwm", "ti,am3352-ehrpwm"; #pwm-cells = <3>; - reg = <0x300000 0x2000>; + reg = <0x4843e200 0x80>; + clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>; + clock-names = "tbclk", "fck"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt index f7eae77f8354..1a5d7b71db89 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -1,7 +1,11 @@ TI SOC based PWM Subsystem Required properties: -- compatible: Must be "ti,am33xx-pwmss"; +- compatible: Must be "ti,<soc>-pwmss". + for am33xx - compatible = "ti,am33xx-pwmss"; + for am4372 - compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + for dra746 - compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss" + - reg: physical base address and size of the registers map. - address-cells: Specify the number of u32 entries needed in child nodes. Should set to 1. @@ -16,7 +20,7 @@ Required properties: Also child nodes should also populated under PWMSS DT node. Example: -pwmss0: pwmss@48300000 { +epwmss0: epwmss@48300000 { /* PWMSS for am33xx */ compatible = "ti,am33xx-pwmss"; reg = <0x48300000 0x10>; ti,hwmods = "epwmss0"; @@ -29,3 +33,28 @@ pwmss0: pwmss@48300000 { /* child nodes go here */ }; + +epwmss0: epwmss@48300000 { /* PWMSS for am4372 */ + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss" + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; + +epwmss0: epwmss@4843e000 { /* PWMSS for DRA7xx */ + compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss"; + reg = <0x4843e000 0x30>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt index 0822a083fc57..d6de64335022 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -7,6 +7,7 @@ Required Properties: - "renesas,pwm-r8a7790": for R-Car H2 - "renesas,pwm-r8a7791": for R-Car M2-W - "renesas,pwm-r8a7794": for R-Car E2 + - "renesas,pwm-r8a7795": for R-Car H3 - reg: base address and length of the registers block for the PWM. - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt new file mode 100644 index 000000000000..cb209646bf13 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt @@ -0,0 +1,18 @@ +== ST STMPE PWM controller == + +This is a PWM block embedded in the ST Microelectronics STMPE +(ST Multi-Purpose Expander) chips. The PWM is registered as a +subdevices of the STMPE MFD device. + +Required properties: +- compatible: should be: + - "st,stmpe-pwm" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +pwm0: pwm { + compatible = "st,stmpe-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index 0127be360fe8..873096be0278 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -14,7 +14,7 @@ architectures that typically run big-endian operating systems be marked that way in the devicetree. On SoCs that can be operated in both big-endian and little-endian -modes, with a single hardware switch controlling both the endianess +modes, with a single hardware switch controlling both the endianness of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS chips), "native-endian" is used to allow using the same device tree blob in both cases. diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index 7aa9b1fa6b21..58065ca9e3b4 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -1,4 +1,4 @@ -* Dialog Semiconductor DA9210 Voltage Regulator +* Dialog Semiconductor DA9210 Multi-phase 12A DCDC BUCK Converter Required properties: @@ -18,8 +18,12 @@ Example: compatible = "dlg,da9210"; reg = <0x68>; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1000000>; + interrupt-parent = <...>; + interrupts = <...>; + + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <1600000>; + regulator-max-microamp = <4600000>; regulator-boot-on; - regulator-always-on; }; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index c620493e8dbe..0f2a6f8fcafd 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,7 +1,8 @@ -* Dialog Semiconductor DA9211/DA9213/DA9215 Voltage Regulator +* Dialog Semiconductor DA9211/DA9212/DA9213/DA9214/DA9215 Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9213" or "dlg,da9215" +- compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" + or "dlg,da9214" or "dlg,da9215" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -30,6 +31,25 @@ Example 1) DA9211 regulator-max-microamp = <5000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 2) DA9212 + + pmic: da9212@68 { + compatible = "dlg,da9212"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -41,7 +61,7 @@ Example 1) DA9211 }; }; -Example 2) DA9213 +Example 3) DA9213 pmic: da9213@68 { compatible = "dlg,da9213"; reg = <0x68>; @@ -56,6 +76,24 @@ Example 2) DA9213 regulator-max-microamp = <6000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 4) DA9214 + pmic: da9214@68 { + compatible = "dlg,da9214"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -67,8 +105,7 @@ Example 2) DA9213 }; }; - -Example 3) DA9215 +Example 5) DA9215 pmic: da9215@68 { compatible = "dlg,da9215"; reg = <0x68>; diff --git a/Documentation/devicetree/bindings/regulator/ltc3676.txt b/Documentation/devicetree/bindings/regulator/ltc3676.txt new file mode 100644 index 000000000000..d4eb366ce18c --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ltc3676.txt @@ -0,0 +1,94 @@ +Linear Technology LTC3676 8-output regulators + +Required properties: +- compatible: "lltc,ltc3676" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from: +412.5mV to 800mV in 12.5 mV steps. The output voltage thus ranges between +0.4125 * (1 + R1/R2) V and 0.8 * (1 + R1/R2) V. + +Regulators ldo1, ldo2, and ldo4 have a fixed 0.725 V reference and thus output +0.725 * (1 + R1/R2) V. The ldo3 regulator is fixed to 1.8 V. The ldo1 standby +regulator can not be disabled and thus should have the regulator-always-on +property set. + +Example: + + ltc3676: pmic@3c { + compatible = "lltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <1308000>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1033310>; + regulator-max-microvolt = <200400>; + lltc,fb-voltage-divider = <301000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <130800>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <868310>; + regulator-max-microvolt = <168400>; + lltc,fb-voltage-divider = <221000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <2490375>; + regulator-max-microvolt = <2490375>; + lltc,fb-voltage-divider = <487000 200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <3023250>; + regulator-max-microvolt = <3023250>; + lltc,fb-voltage-divider = <634000 200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt new file mode 100644 index 000000000000..c35d878b0960 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt @@ -0,0 +1,237 @@ +Mediatek MT6323 Regulator Driver + +All voltage regulators are defined as subnodes of the regulators node. A list +of regulators provided by this controller are defined as subnodes of the +PMIC's node. Each regulator is named according to its regulator type, +buck_<name> and ldo_<name>. The definition for each of these nodes is defined +using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vproc, buck_vsys, buck_vpa +LDO: + ldo_vtcxo, ldo_vcn28, ldo_vcn33_bt, ldo_vcn33_wifi, ldo_va, ldo_vcama, + ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, ldo_vemc3v3, ldo_vgp1, ldo_vgp2, + ldo_vgp3, ldo_vcn18, ldo_vsim1, ldo_vsim2, ldo_vrtc, ldo_vcamaf, ldo_vibr, + ldo_vrf18, ldo_vm, ldo_vio18, ldo_vcamd, ldo_vcamio + +Example: + + pmic: mt6323 { + mt6323regulator: regulators { + mt6323_vproc_reg: buck_vproc{ + regulator-name = "vproc"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vsys_reg: buck_vsys{ + regulator-name = "vsys"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2987500>; + regulator-ramp-delay = <25000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vpa_reg: buck_vpa{ + regulator-name = "vpa"; + regulator-min-microvolt = < 500000>; + regulator-max-microvolt = <3650000>; + }; + + mt6323_vtcxo_reg: ldo_vtcxo{ + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcn28_reg: ldo_vcn28{ + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_bt_reg: ldo_vcn33_bt{ + regulator-name = "vcn33_bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_wifi_reg: ldo_vcn33_wifi{ + regulator-name = "vcn33_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_va_reg: ldo_va{ + regulator-name = "va"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcama_reg: ldo_vcama{ + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vio28_reg: ldo_vio28{ + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vusb_reg: ldo_vusb{ + regulator-name = "vusb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + regulator-boot-on; + }; + + mt6323_vmc_reg: ldo_vmc{ + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vmch_reg: ldo_vmch{ + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vemc3v3_reg: ldo_vemc3v3{ + regulator-name = "vemc3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vgp1_reg: ldo_vgp1{ + regulator-name = "vgp1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp2_reg: ldo_vgp2{ + regulator-name = "vgp2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp3_reg: ldo_vgp3{ + regulator-name = "vgp3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcn18_reg: ldo_vcn18{ + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim1_reg: ldo_vsim1{ + regulator-name = "vsim1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim2_reg: ldo_vsim2{ + regulator-name = "vsim2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vrtc_reg: ldo_vrtc{ + regulator-name = "vrtc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamaf_reg: ldo_vcamaf{ + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vibr_reg: ldo_vibr{ + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + }; + + mt6323_vrf18_reg: ldo_vrf18{ + regulator-name = "vrf18"; + regulator-min-microvolt = <1825000>; + regulator-max-microvolt = <1825000>; + regulator-enable-ramp-delay = <187>; + }; + + mt6323_vm_reg: ldo_vm{ + regulator-name = "vm"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vio18_reg: ldo_vio18{ + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamd_reg: ldo_vcamd{ + regulator-name = "vcamd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcamio_reg: ldo_vcamio{ + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index 725393c8a7f2..99872819604f 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -1,5 +1,12 @@ * palmas regulator IP block devicetree bindings +The tps659038 for the AM57x class have OTP spins that +have different part numbers but the same functionality. There +is not a need to add the OTP spins to the palmas driver. The +spin devices should use the tps659038 as it's compatible value. +This is the list of those devices: +tps659037 + Required properties: - compatible : Should be from the list ti,twl6035-pmic @@ -8,6 +15,7 @@ Required properties: ti,tps65913-pmic ti,tps65914-pmic ti,tps65917-pmic + ti,tps659038-pmic and also the generic series names ti,palmas-pmic - interrupt-parent : The parent interrupt controller which is palmas. diff --git a/Documentation/devicetree/bindings/regulator/pv88080.txt b/Documentation/devicetree/bindings/regulator/pv88080.txt index 38a614210dcb..e6e4b9c82d89 100644 --- a/Documentation/devicetree/bindings/regulator/pv88080.txt +++ b/Documentation/devicetree/bindings/regulator/pv88080.txt @@ -1,22 +1,28 @@ * Powerventure Semiconductor PV88080 Voltage Regulator Required properties: -- compatible: "pvs,pv88080". -- reg: I2C slave address, usually 0x49. +- compatible: Must be one of the following, depending on the + silicon version: + - "pvs,pv88080" (DEPRECATED) + + - "pvs,pv88080-aa" for PV88080 AA or AB silicon + - "pvs,pv88080-ba" for PV88080 BA or BB silicon + NOTE: The use of the compatibles with no silicon version is deprecated. +- reg: I2C slave address, usually 0x49 - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed below. The content of each sub-node is defined by the standard binding for regulators; see regulator.txt. - BUCK1, BUCK2, and BUCK3. + BUCK1, BUCK2, BUCK3 and HVBUCK. Optional properties: - Any optional property defined in regulator.txt -Example +Example: pmic: pv88080@49 { - compatible = "pvs,pv88080"; + compatible = "pvs,pv88080-ba"; reg = <0x49>; interrupt-parent = <&gpio>; interrupts = <24 24>; @@ -45,5 +51,12 @@ Example regulator-min-microamp = <1496000>; regulator-max-microamp = <4189000>; }; + + HVBUCK { + regulator-name = "hvbuck"; + regulator-min-microvolt = < 5000>; + regulator-max-microvolt = <1275000>; + }; }; }; + diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ed936f0f34f2..3aeba9f86ed8 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -34,20 +34,44 @@ Only required for Voltage Table Mode: First cell is voltage in microvolts (uV) Second cell is duty-cycle in percent (%) +Optional properties for Continuous mode: +- pwm-dutycycle-unit: Integer value encoding the duty cycle unit. If not + defined, <100> is assumed, meaning that + pwm-dutycycle-range contains values expressed in + percent. + +- pwm-dutycycle-range: Should contain 2 entries. The first entry is encoding + the dutycycle for regulator-min-microvolt and the + second one the dutycycle for regulator-max-microvolt. + Duty cycle values are expressed in pwm-dutycycle-unit. + If not defined, <0 100> is assumed. + NB: To be clear, if voltage-table is provided, then the device will be used in Voltage Table Mode. If no voltage-table is provided, then the device will be used in Continuous Voltage Mode. +Optional properties: +-------------------- +- enable-gpios: GPIO to use to enable/disable the regulator + Any property defined as part of the core regulator binding can also be used. (See: ../regulator/regulator.txt) -Continuous Voltage Example: +Continuous Voltage With Enable GPIO Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; regulator-min-microvolt = <1016000>; regulator-max-microvolt = <1114000>; regulator-name = "vdd_logic"; + /* unit == per-mille */ + pwm-dutycycle-unit = <1000>; + /* + * Inverted PWM logic, and the duty cycle range is limited + * to 30%-70%. + */ + pwm-dutycycle-range <700 300>; /* */ }; Voltage Table Example: diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 46c6f3ed1a1c..0fa3b0fac129 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -113,9 +113,9 @@ pm8916: l14, l15, l16, l17, l18 pm8941: - s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, - l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, - mvs1, mvs2 + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, + 5vs1, 5vs2 pm8994: s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc593cac15..6ab5aef619d9 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -13,7 +13,7 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - regulator-allow-set-load: allow the regulator performance level to be configured - <name>-supply: phandle to the parent supply/regulator node -- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-ramp-delay: ramp delay for regulator(in uV/us) For hardware which supports disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. - regulator-enable-ramp-delay: The time taken, in microseconds, for the supply diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt new file mode 100644 index 000000000000..57cb49ec55ca --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -0,0 +1,137 @@ +Qualcomm Hexagon Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm Hexagon core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,q6v5-pil" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the qdsp6 and + rmb register blocks + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: must be "q6dsp" and "rmb" + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog, fatal IRQs ready, handover and + stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + +- clocks: + Usage: required + Value type: <phandle> + Definition: reference to the iface, bus and mem clocks to be held on + behalf of the booting of the Hexagon core + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "iface", "bus", "mem" + +- resets: + Usage: required + Value type: <phandle> + Definition: reference to the reset-controller for the modem sub-system + +- reset-names: + Usage: required + Value type: <stringlist> + Definition: must be "mss_restart" + +- cx-supply: +- mss-supply: +- mx-supply: +- pll-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the Hexagon core + +- qcom,smem-states: + Usage: required + Value type: <phandle> + Definition: reference to the smem state for requesting the Hexagon to + shut down + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must be "stop" + +- qcom,halt-regs: + Usage: required + Value type: <prop-encoded-array> + Definition: a phandle reference to a syscon representing TCSR followed + by the three offsets within syscon for q6, modem and nc + halt registers. + += SUBNODES: +The Hexagon node must contain two subnodes, named "mba" and "mpss" representing +the memory regions used by the Hexagon firmware. Each sub-node must contain: + +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the region + += EXAMPLE +The following example describes the resources needed to boot control the +Hexagon, as it is found on MSM8974 boards. + + modem-rproc@fc880000 { + compatible = "qcom,q6v5-pil"; + reg = <0xfc880000 0x100>, + <0xfc820000 0x020>; + reg-names = "qdsp6", "rmb"; + + interrupts-extended = <&intc 0 24 1>, + <&modem_smp2p_in 0 0>, + <&modem_smp2p_in 1 0>, + <&modem_smp2p_in 2 0>, + <&modem_smp2p_in 3 0>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, + <&gcc GCC_MSS_CFG_AHB_CLK>, + <&gcc GCC_BOOT_ROM_AHB_CLK>; + clock-names = "iface", "bus", "mem"; + + qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>; + + resets = <&gcc GCC_MSS_RESTART>; + reset-names = "mss_restart"; + + cx-supply = <&pm8841_s2>; + mss-supply = <&pm8841_s3>; + mx-supply = <&pm8841_s1>; + pll-supply = <&pm8941_l12>; + + qcom,smem-states = <&modem_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + mba { + memory-region = <&mba_region>; + }; + + mpss { + memory-region = <&mpss_region>; + }; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt new file mode 100644 index 000000000000..0d2361ebe3d7 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt @@ -0,0 +1,132 @@ +Qualcomm WCNSS Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm WCNSS core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,riva-pil", + "qcom,pronto-v1-pil", + "qcom,pronto-v2-pil" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the CCU, DXE and + PMU register blocks + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: must be "ccu", "dxe", "pmu" + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog and fatal IRQs and may specify the + ready, handover and stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: should be "wdog", "fatal", optionally followed by "ready", + "handover", "stop-ack" + +- vddmx-supply: +- vddcx-supply: +- vddpx-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the WCNSS core + +- qcom,smem-states: + Usage: optional + Value type: <prop-encoded-array> + Definition: reference to the SMEM state used to indicate to WCNSS that + it should shut down + +- qcom,smem-state-names: + Usage: optional + Value type: <stringlist> + Definition: should be "stop" + +- memory-region: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to reserved-memory node for the remote processor + see ../reserved-memory/reserved-memory.txt + += SUBNODES +A single subnode of the WCNSS PIL describes the attached rf module and its +resource dependencies. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,wcn3620", + "qcom,wcn3660", + "qcom,wcn3680" + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the xo clock and optionally the rf clock + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: should be "xo", optionally followed by "rf" + +- vddxo-supply: +- vddrfa-supply: +- vddpa-supply: +- vdddig-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the WCNSS core + += EXAMPLE +The following example describes the resources needed to boot control the WCNSS, +with attached WCN3680, as it is commonly found on MSM8974 boards. + +pronto@fb204000 { + compatible = "qcom,pronto-v2-pil"; + reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>; + reg-names = "ccu", "dxe", "pmu"; + + interrupts-extended = <&intc 0 149 1>, + <&wcnss_smp2p_slave 0 0>, + <&wcnss_smp2p_slave 1 0>, + <&wcnss_smp2p_slave 2 0>, + <&wcnss_smp2p_slave 3 0>; + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; + + vddmx-supply = <&pm8841_s1>; + vddcx-supply = <&pm8841_s2>; + vddpx-supply = <&pm8941_s3>; + + qcom,smem-states = <&wcnss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + memory-region = <&wcnss_region>; + + pinctrl-names = "default"; + pinctrl-0 = <&wcnss_pin_a>; + + iris { + compatible = "qcom,wcn3680"; + + clocks = <&rpmcc RPM_CXO_CLK_SRC>, <&rpmcc RPM_CXO_A2>; + clock-names = "xo", "rf"; + + vddxo-supply = <&pm8941_l6>; + vddrfa-supply = <&pm8941_l11>; + vddpa-supply = <&pm8941_l19>; + vdddig-supply = <&pm8941_s3>; + }; +}; diff --git a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt new file mode 100644 index 000000000000..e81f821a2135 --- /dev/null +++ b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt @@ -0,0 +1,48 @@ +Ramoops oops/panic logger +========================= + +ramoops provides persistent RAM storage for oops and panics, so they can be +recovered after a reboot. This is a child-node of "/reserved-memory", and +is named "ramoops" after the backend, rather than "pstore" which is the +subsystem. + +Parts of this storage may be set aside for other persistent log buffers, such +as kernel log messages, or for optional ECC error-correction data. The total +size of these optional buffers must fit in the reserved region. + +Any remaining space will be used for a circular buffer of oops and panic +records. These records have a configurable size, with a size of 0 indicating +that they should be disabled. + +At least one of "record-size", "console-size", "ftrace-size", or "pmsg-size" +must be set non-zero, but are otherwise optional as listed below. + + +Required properties: + +- compatible: must be "ramoops" + +- reg: region of memory that is preserved between reboots + + +Optional properties: + +- ecc-size: enables ECC support and specifies ECC buffer size in bytes + (defaults to 0: no ECC) + +- record-size: maximum size in bytes of each dump done on oops/panic + (defaults to 0: disabled) + +- console-size: size in bytes of log buffer reserved for kernel messages + (defaults to 0: disabled) + +- ftrace-size: size in bytes of log buffer reserved for function tracing and + profiling (defaults to 0: disabled) + +- pmsg-size: size in bytes of log buffer reserved for userspace messages + (defaults to 0: disabled) + +- unbuffered: if present, use unbuffered mappings to map the reserved region + (defaults to buffered mappings) + +- no-dump-oops: if present, only dump panics (defaults to panics and oops) diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt new file mode 100644 index 000000000000..e746b631793a --- /dev/null +++ b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt @@ -0,0 +1,18 @@ +Amlogic Meson SoC Reset Controller +======================================= + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "amlogic,meson8b-reset" or "amlogic,meson-gxbb-reset" +- reg: should contain the register address base +- #reset-cells: 1, see below + +example: + +reset: reset-controller { + compatible = "amlogic,meson-gxbb-reset"; + reg = <0x0 0x04404 0x0 0x20>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt index e0b185a944ba..c25da39df707 100644 --- a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -8,7 +8,9 @@ The reset controller registers are part of the system-ctl block on hi6220 SoC. Required properties: -- compatible: may be "hisilicon,hi6220-sysctrl" +- compatible: should be one of the following: + - "hisilicon,hi6220-sysctrl", "syscon" : For peripheral reset controller. + - "hisilicon,hi6220-mediactrl", "syscon" : For media reset controller. - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below diff --git a/Documentation/devicetree/bindings/reset/oxnas,reset.txt b/Documentation/devicetree/bindings/reset/oxnas,reset.txt new file mode 100644 index 000000000000..6f06db930030 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/oxnas,reset.txt @@ -0,0 +1,58 @@ +Oxford Semiconductor OXNAS SoC Family RESET Controller +================================================ + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "oxsemi,ox810se-reset" +- #reset-cells: 1, see below + +Parent node should have the following properties : +- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + +For OX810SE, the indices are : + - 0 : ARM + - 1 : COPRO + - 2 : Reserved + - 3 : Reserved + - 4 : USBHS + - 5 : USBHSPHY + - 6 : MAC + - 7 : PCI + - 8 : DMA + - 9 : DPE + - 10 : DDR + - 11 : SATA + - 12 : SATA_LINK + - 13 : SATA_PHY + - 14 : Reserved + - 15 : NAND + - 16 : GPIO + - 17 : UART1 + - 18 : UART2 + - 19 : MISC + - 20 : I2S + - 21 : AHB_MON + - 22 : UART3 + - 23 : UART4 + - 24 : SGDMA + - 25 : Reserved + - 26 : Reserved + - 27 : Reserved + - 28 : Reserved + - 29 : Reserved + - 30 : Reserved + - 31 : BUS + +example: + +sys: sys-ctrl@000000 { + compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"; + reg = <0x000000 0x100000>; + + reset: reset-controller { + compatible = "oxsemi,ox810se-reset"; + #reset-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt new file mode 100644 index 000000000000..164c7f34c451 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt @@ -0,0 +1,91 @@ +TI SysCon Reset Controller +======================= + +Almost all SoCs have hardware modules that require reset control in addition +to clock and power control for their functionality. The reset control is +typically provided by means of memory-mapped I/O registers. These registers are +sometimes a part of a larger register space region implementing various +functionalities. This register range is best represented as a syscon node to +allow multiple entities to access their relevant registers in the common +register space. + +A SysCon Reset Controller node defines a device that uses a syscon node +and provides reset management functionality for various hardware modules +present on the SoC. + +SysCon Reset Controller Node +============================ +Each of the reset provider/controller nodes should be a child of a syscon +node and have the following properties. + +Required properties: +-------------------- + - compatible : Should be, + "ti,k2e-pscrst" + "ti,k2l-pscrst" + "ti,k2hk-pscrst" + "ti,syscon-reset" + - #reset-cells : Should be 1. Please see the reset consumer node below + for usage details + - ti,reset-bits : Contains the reset control register information + Should contain 7 cells for each reset exposed to + consumers, defined as: + Cell #1 : offset of the reset assert control + register from the syscon register base + Cell #2 : bit position of the reset in the reset + assert control register + Cell #3 : offset of the reset deassert control + register from the syscon register base + Cell #4 : bit position of the reset in the reset + deassert control register + Cell #5 : offset of the reset status register + from the syscon register base + Cell #6 : bit position of the reset in the + reset status register + Cell #7 : Flags used to control reset behavior, + availible flags defined in the DT include + file <dt-bindings/reset/ti-syscon.h> + +SysCon Reset Consumer Nodes +=========================== +Each of the reset consumer nodes should have the following properties, +in addition to their own properties. + +Required properties: +-------------------- + - resets : A phandle to the reset controller node and an index number + to a reset specifier as defined above. + +Please also refer to Documentation/devicetree/bindings/reset/reset.txt for +common reset controller usage by consumers. + +Example: +-------- +The following example demonstrates a syscon node, the reset controller node +using the syscon node, and a consumer (a DSP device) on the TI Keystone 2 +Edison SoC. + +/ { + soc { + psc: power-sleep-controller@02350000 { + compatible = "syscon", "simple-mfd"; + reg = <0x02350000 0x1000>; + + pscrst: psc-reset { + compatible = "ti,k2e-pscrst", "ti,syscon-reset"; + #reset-cells = <1>; + + ti,reset-bits = < + 0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_SET|DEASSERT_CLEAR|STATUS_SET) /* 0: pcrst-dsp0 */ + 0xa40 5 0xa44 3 0 0 (ASSERT_SET|DEASSERT_CLEAR|STATUS_NONE) /* 1: pcrst-example */ + >; + }; + }; + + dsp0: dsp0 { + ... + resets = <&pscrst 0>; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt b/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt new file mode 100644 index 000000000000..202f2d09a23f --- /dev/null +++ b/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt @@ -0,0 +1,14 @@ +Amlogic Meson Random number generator +===================================== + +Required properties: + +- compatible : should be "amlogic,meson-rng" +- reg : Specifies base physical address and size of the registers. + +Example: + +rng { + compatible = "amlogic,meson-rng"; + reg = <0x0 0xc8834000 0x0 0x4>; +}; diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt index 07ccdaa68324..26542690b578 100644 --- a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt @@ -2,7 +2,8 @@ BCM2835 Random number generator Required properties: -- compatible : should be "brcm,bcm2835-rng" +- compatible : should be "brcm,bcm2835-rng" or "brcm,bcm-nsp-rng" or + "brcm,bcm5301x-rng" - reg : Specifies base physical address and size of the registers. Example: @@ -11,3 +12,8 @@ rng { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; }; + +rng@18033000 { + compatible = "brcm,bcm-nsp-rng"; + reg = <0x18033000 0x14>; +}; diff --git a/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt new file mode 100644 index 000000000000..ba470c56cdec --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt @@ -0,0 +1,46 @@ +* Maxim/Dallas Semiconductor DS-1302 RTC + +Simple device which could be used to store date/time between reboots. + +The device uses the standard MicroWire half-duplex transfer timing. +Master output is set on low clock and sensed by the RTC on the rising +edge. Master input is set by the RTC on the trailing edge and is sensed +by the master on low clock. + +Required properties: + +- compatible : Should be "maxim,ds1302" + +Required SPI properties: + +- reg : Should be address of the device chip select within + the controller. + +- spi-max-frequency : DS-1302 has 500 kHz if powered at 2.2V, + and 2MHz if powered at 5V. + +- spi-3wire : The device has a shared signal IN/OUT line. + +- spi-lsb-first : DS-1302 requires least significant bit first + transfers. + +- spi-cs-high: DS-1302 has active high chip select line. This is + required unless inverted in hardware. + +Example: + +spi@901c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "icpdas,lp8841-spi-rtc"; + reg = <0x901c 0x1>; + + rtc@0 { + compatible = "maxim,ds1302"; + reg = <0>; + spi-max-frequency = <500000>; + spi-3wire; + spi-lsb-first; + spi-cs-high; + }; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-opal.txt b/Documentation/devicetree/bindings/rtc/rtc-opal.txt index a1734e5cb75b..2340938cd0f5 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-opal.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-opal.txt @@ -2,7 +2,7 @@ IBM OPAL real-time clock ------------------------ Required properties: -- comapatible: Should be "ibm,opal-rtc" +- compatible: Should be "ibm,opal-rtc" Optional properties: - wakeup-source: Decides if the wakeup is supported or not diff --git a/Documentation/devicetree/bindings/rtc/rtc-palmas.txt b/Documentation/devicetree/bindings/rtc/rtc-palmas.txt index adbccc0a51e1..eb1c7fdeb413 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-palmas.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-palmas.txt @@ -15,9 +15,9 @@ Optional properties: battery is chargeable or not. If charging battery then driver can enable the charging. - ti,backup-battery-charge-high-current: Enable high current charging in - backup battery. Device supports the < 100mA and > 100mA charging. - The high current will be > 100mA. Absence of this property will - charge battery to lower current i.e. < 100mA. + backup battery. Device supports the < 100uA and > 100uA charging. + The high current will be > 100uA. Absence of this property will + charge battery to lower current i.e. < 100uA. Example: palmas: tps65913@58 { diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt index 0cda19ad4859..968ac820254b 100644 --- a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt @@ -13,5 +13,5 @@ Example: compatible = "mrvl,mmp-rtc"; reg = <0xd4010000 0x1000>; interrupts = <5>, <6>; - interrupt-name = "rtc 1Hz", "rtc alarm"; + interrupt-names = "rtc 1Hz", "rtc alarm"; }; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt new file mode 100644 index 000000000000..85741cd468cc --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt @@ -0,0 +1,24 @@ +Required properties: +- compatible: should be one of the following + "st,st33htpm-spi" + "infineon,slb9670" + "tcg,tpm_tis-spi" +- spi-max-frequency: Maximum SPI frequency (depends on TPMs). + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with TPM_TIS on SPI4): + +&mcspi4 { + + status = "okay"; + + tpm_tis@0 { + + compatible = "tcg,tpm_tis-spi"; + + spi-max-frequency = <10000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 936ab5b87324..f86bb06c39e9 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,6 +42,8 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. +- tx-threshold: Specify the TX FIFO low water indication for parts with + programmable TX FIFO thresholds. Note: * fsl,ns16550: diff --git a/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt new file mode 100644 index 000000000000..128cc6aed001 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt @@ -0,0 +1,19 @@ +ARM MPS2 UART + +Required properties: +- compatible : Should be "arm,mps2-uart" +- reg : Address and length of the register set +- interrupts : Reference to the UART RX, TX and overrun interrupts + +Required clocking property: +- clocks : The input clock of the UART + + +Examples: + +uart0: serial@40004000 { + compatible = "arm,mps2-uart"; + reg = <0x40004000 0x1000>; + interrupts = <0 1 12>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt index caaeb2583579..07013fa60a48 100644 --- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt +++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART) Required properties: -- compatible: Should be "cirrus,clps711x-uart". +- compatible: Should be "cirrus,ep7209-uart". - reg: Address and length of the register set for the device. - interrupts: Should contain UART TX and RX interrupt. - clocks: Should contain UART core clock number. @@ -20,7 +20,7 @@ Example: }; uart1: uart@80000480 { - compatible = "cirrus,clps711x-uart"; + compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart"; reg = <0x80000480 0x80>; interrupts = <12 13>; clocks = <&clks 11>; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index ed94c217c98d..1e82802d8e32 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -6,7 +6,7 @@ Required properties: - interrupts : Should contain uart interrupt Optional properties: -- fsl,uart-has-rtscts : Indicate the uart has rts and cts +- uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. @@ -24,6 +24,6 @@ uart1: serial@73fbc000 { compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fbc000 0x4000>; interrupts = <31>; - fsl,uart-has-rtscts; + uart-has-rtscts; fsl,dte-mode; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt index 7c408c87e613..5c96d41899f1 100644 --- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt @@ -1,8 +1,10 @@ * Freescale MXS Application UART (AUART) -Required properties: -- compatible : Should be "fsl,<soc>-auart". The supported SoCs include - imx23 and imx28. +Required properties for all SoCs: +- compatible : Should be one of fallowing variants: + "fsl,imx23-auart" - Freescale i.MX23 + "fsl,imx28-auart" - Freescale i.MX28 + "alphascale,asm9260-auart" - Alphascale ASM9260 - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers - dmas: DMA specifier, consisting of a phandle to DMA controller node @@ -10,8 +12,14 @@ Required properties: Refer to dma.txt and fsl-mxs-dma.txt for details. - dma-names: "rx" for RX channel, "tx" for TX channel. +Required properties for "alphascale,asm9260-auart": +- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt +- clock-names : should be set to + "mod" - source for tick counter. + "ahb" - ahb gate. + Optional properties: -- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines +- uart-has-rtscts : Indicate the UART has RTS and CTS lines for hardware flow control, it also means you enable the DMA support for this UART. - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD diff --git a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt new file mode 100644 index 000000000000..7a34345d0ca3 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt @@ -0,0 +1,29 @@ +* Microchip Universal Asynchronous Receiver Transmitter (UART) + +Required properties: +- compatible: Should be "microchip,pic32mzda-uart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the UART peripheral. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +Optional properties: +- cts-gpios: CTS pin for UART + +Example: + uart1: serial@1f822000 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822000 0x50>; + interrupts = <112 IRQ_TYPE_LEVEL_HIGH>, + <113 IRQ_TYPE_LEVEL_HIGH>, + <114 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rootclk PB2CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 + &pinctrl_uart1_cts + &pinctrl_uart1_rts>; + cts-gpios = <&gpio1 15 0>; + }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index e99e10ab9ecb..0015c722be7b 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -6,6 +6,7 @@ Required properties: * "mediatek,mt6580-uart" for MT6580 compatible UARTS * "mediatek,mt6582-uart" for MT6582 compatible UARTS * "mediatek,mt6589-uart" for MT6589 compatible UARTS + * "mediatek,mt6755-uart" for MT6755 compatible UARTS * "mediatek,mt6795-uart" for MT6795 compatible UARTS * "mediatek,mt7623-uart" for MT7623 compatible UARTS * "mediatek,mt8127-uart" for MT8127 compatible UARTS diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt index 6087defd9f93..6087defd9f93 100644 --- a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index 182777fac9a2..d5f73b8f614f 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -28,10 +28,10 @@ Optional properties: - dma-names: Should contain "tx" for transmit and "rx" for receive channels - qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be used with TX DMA channel. Required when using DMA for transmission - with UARTDM v1.3 and bellow. + with UARTDM v1.3 and below. - qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be used with RX DMA channel. Required when using DMA for reception - with UARTDM v1.3 and bellow. + with UARTDM v1.3 and below. Note: Aliases may be defined to ensure the correct ordering of the UARTs. The alias serialN will result in the UART being assigned port N. If any diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 528c3b90f23c..1e4000d83aee 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -31,6 +31,8 @@ Required properties: - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. + - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. + - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, @@ -76,6 +78,10 @@ Optional properties: - dmas: Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. - dma-names: Must contain a list of two DMA names, "tx" and "rx". + - {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the + generic serial DT bindings in serial.txt. + - uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow + control, cfr. the generic serial DT bindings in serial.txt. Example: aliases { diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt new file mode 100644 index 000000000000..fd970f76a7b8 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -0,0 +1,57 @@ +Generic Serial DT Bindings + +This document lists a set of generic properties for describing UARTs in a +device tree. Whether these properties apply to a particular device depends on +the DT bindings for the actual device. + +Optional properties: + - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's CTS line. + - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DCD line. + - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DSR line. + - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DTR line. + - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's RNG line. + - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's RTS line. + + - uart-has-rtscts: The presence of this property indicates that the + UART has dedicated lines for RTS/CTS hardware flow control, and that + they are available for use (wired and enabled by pinmux configuration). + This depends on both the UART hardware and the board wiring. + Note that this property is mutually-exclusive with "cts-gpios" and + "rts-gpios" above. + + +Examples: + + uart1: serial@48022000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + reg = <0x48022000 0x2000>; + interrupts = <73>; + dmas = <&edma 28 0>, <&edma 29 0>; + dma-names = "tx", "rx"; + dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; + cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + + scifa4: serial@e6c80000 { + compatible = "renesas,scifa-sh73a0", "renesas,scifa"; + reg = <0xe6c80000 0x100>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>; + clock-names = "fck"; + power-domains = <&pd_a3sp>; + uart-has-rtscts; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt index 67e2a0aeb042..1e48bbbeecc6 100644 --- a/Documentation/devicetree/bindings/serial/sirf-uart.txt +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -9,9 +9,9 @@ Required properties: - clocks : Should contain uart clock number Optional properties: -- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware -- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true -- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true +- uart-has-rtscts: we have hardware flow controller pins in hardware +- rts-gpios: RTS pin for USP-based UART if uart-has-rtscts is true +- cts-gpios: CTS pin for USP-based UART if uart-has-rtscts is true Example: @@ -28,7 +28,7 @@ On the board-specific dts, we can put rts-gpios and cts-gpios like usp@b0090000 { compatible = "sirf,prima2-usp-uart"; - sirf,uart-has-rtscts; + uart-has-rtscts; rts-gpios = <&gpio 15 0>; cts-gpios = <&gpio 46 0>; }; diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt new file mode 100644 index 000000000000..85ec5f2b1996 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -0,0 +1,46 @@ +* STMicroelectronics STM32 USART + +Required properties: +- compatible: Can be either "st,stm32-usart", "st,stm32-uart", +"st,stm32f7-usart" or "st,stm32f7-uart" depending on whether +the device supports synchronous mode and is compatible with +stm32(f4) or stm32f7. +- reg: The address and length of the peripheral registers space +- interrupts: The interrupt line of the USART instance +- clocks: The input clock of the USART instance + +Optional properties: +- pinctrl: The reference on the pins configuration +- st,hw-flow-ctrl: bool flag to enable hardware flow control. +- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt +- dma-names: "rx" and/or "tx" + +Examples: +usart4: serial@40004c00 { + compatible = "st,stm32-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + clocks = <&clk_pclk1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart4>; +}; + +usart2: serial@40004400 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40004400 0x400>; + interrupts = <38>; + clocks = <&clk_pclk1>; + st,hw-flow-ctrl; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>; +}; + +usart1: serial@40011000 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 164>; + dmas = <&dma2 2 4 0x414 0x0>, + <&dma2 7 4 0x414 0x0>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm.txt index 160c752484b4..160c752484b4 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/brg.txt index 4c7d45eaf025..4c7d45eaf025 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/brg.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/i2c.txt index 87bc6048667e..87bc6048667e 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/i2c.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/pic.txt index 8e3ee1681618..8e3ee1681618 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/pic.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/usb.txt index 74bfda4bb824..74bfda4bb824 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/usb.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/gpio.txt index 349f79fd7076..349f79fd7076 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/gpio.txt diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt new file mode 100644 index 000000000000..03c741602c6d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt @@ -0,0 +1,124 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; + +* HDLC + +Currently defined compatibles: +- fsl,ucc-hdlc + +Properties for fsl,ucc-hdlc: +- rx-clock-name +- tx-clock-name + Usage: required + Value type: <string> + Definition : Must be "brg1"-"brg16" for internal clock source, + Must be "clk1"-"clk24" for external clock source. + +- fsl,tdm-interface + Usage: optional + Value type: <empty> + Definition : Specify that hdlc is based on tdm-interface + +The property below is dependent on fsl,tdm-interface: +- fsl,rx-sync-clock + Usage: required + Value type: <string> + Definition : Must be "none", "rsync_pin", "brg9-11" and "brg13-15". + +- fsl,tx-sync-clock + Usage: required + Value type: <string> + Definition : Must be "none", "tsync_pin", "brg9-11" and "brg13-15". + +- fsl,tdm-framer-type + Usage: required for tdm interface + Value type: <string> + Definition : "e1" or "t1".Now e1 and t1 are used, other framer types + are not supported. + +- fsl,tdm-id + Usage: required for tdm interface + Value type: <u32> + Definition : number of TDM ID + +- fsl,tx-timeslot-mask +- fsl,rx-timeslot-mask + Usage: required for tdm interface + Value type: <u32> + Definition : time slot mask for TDM operation. Indicates which time + slots used for transmitting and receiving. + +- fsl,siram-entry-id + Usage: required for tdm interface + Value type: <u32> + Definition : Must be 0,2,4...64. the number of TDM entry. + +- fsl,tdm-internal-loopback + usage: optional for tdm interface + value type: <empty> + Definition : Internal loopback connecting on TDM layer. + +Example for tdm interface: + + ucc@2000 { + compatible = "fsl,ucc-hdlc"; + rx-clock-name = "clk8"; + tx-clock-name = "clk9"; + fsl,rx-sync-clock = "rsync_pin"; + fsl,tx-sync-clock = "tsync_pin"; + fsl,tx-timeslot-mask = <0xfffffffe>; + fsl,rx-timeslot-mask = <0xfffffffe>; + fsl,tdm-framer-type = "e1"; + fsl,tdm-id = <0>; + fsl,siram-entry-id = <0>; + fsl,tdm-interface; + }; + +Example for hdlc without tdm interface: + + ucc@2000 { + compatible = "fsl,ucc-hdlc"; + rx-clock-name = "brg1"; + tx-clock-name = "brg1"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt index 4f8930263dd9..d7afaff5faff 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt @@ -69,6 +69,58 @@ Example: }; }; +* Interrupt Controller (IC) + +Required properties: +- compatible : should be "fsl,qe-ic". +- reg : Address range of IC register set. +- interrupts : interrupts generated by the device. +- interrupt-controller : this device is a interrupt controller. + +Example: + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + interrupts = <95 2 0 0 94 2 0 0>; + }; + +* Serial Interface Block (SI) + +The SI manages the routing of eight TDM lines to the QE block serial drivers +, the MCC and the UCCs, for receive and transmit. + +Required properties: +- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain + "fsl,t1040-qe-si". +- reg : Address range of SI register set. + +Example: + + si1: si@700 { + compatible = "fsl,t1040-qe-si"; + reg = <0x700 0x80>; + }; + +* Serial Interface Block RAM(SIRAM) + +store the routing entries of SI + +Required properties: +- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain + "fsl,t1040-qe-siram". +- reg : Address range of SI RAM. + +Example: + + siram1: siram@1000 { + compatible = "fsl,t1040-qe-siram"; + reg = <0x1000 0x800>; + }; + * QE Firmware Node This node defines a firmware binary that is embedded in the device tree, for diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/firmware.txt index 249db3a15d15..249db3a15d15 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/firmware.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt index 60984260207b..60984260207b 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/pincfg.txt index ec6ee2e864a2..ec6ee2e864a2 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/pincfg.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ucc.txt index e47734bee3f0..e47734bee3f0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ucc.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/usb.txt index 9ccd5f30405b..9ccd5f30405b 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/usb.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/serial.txt index 2ea76d9d137c..2ea76d9d137c 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/serial.txt diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt new file mode 100644 index 000000000000..8823c86c8085 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt @@ -0,0 +1,17 @@ +* Serial + +Required Properties: +compatible : must be "fsl,<chip>-ucc-uart". For t1040, must be +"fsl,t1040-ucc-uart". +port-number : port number of UCC-UART +tx/rx-clock-name : should be "brg1"-"brg16" for internal clock source, + should be "clk1"-"clk28" for external clock source. + +Example: + + ucc_serial: ucc@2200 { + compatible = "fsl,t1040-ucc-uart"; + port-number = <0>; + rx-clock-name = "brg2"; + tx-clock-name = "brg2"; + }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt index ddeb5b6a53c1..107700d00df4 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -18,6 +18,7 @@ IP Pairing Required properties in pwrap device node. - compatible: + "mediatek,mt2701-pwrap" for MT2701/7623 SoCs "mediatek,mt8135-pwrap" for MT8135 SoCs "mediatek,mt8173-pwrap" for MT8173 SoCs - interrupts: IRQ for pwrap in SOC diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt index 5cc82b8353d8..af9ca37221ce 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -68,7 +68,7 @@ important. Value type: <u32> Definition: must be 2 - denoting the bit in the entry and IRQ flags -- #qcom,state-cells: +- #qcom,smem-state-cells: Usage: required for outgoing entries Value type: <u32> Definition: must be 1 - denoting the bit in the entry @@ -92,7 +92,7 @@ wcnss-smp2p { wcnss_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; wcnss_smp2p_in: slave-kernel { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt index a6634c70850d..2993b5a97dd6 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -51,7 +51,7 @@ important. Definition: specifies the offset, in words, of the first bit for this entry -- #qcom,state-cells: +- #qcom,smem-state-cells: Usage: required for local entry Value type: <u32> Definition: must be 1 - denotes bit number @@ -91,7 +91,7 @@ smsm { apps_smsm: apps@0 { reg = <0>; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; wcnss_smsm: wcnss@7 { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt new file mode 100644 index 000000000000..4ea39e9186a7 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt @@ -0,0 +1,116 @@ +Qualcomm WCNSS Binding + +This binding describes the Qualcomm WCNSS hardware. It consists of control +block and a BT, WiFi and FM radio block, all using SMD as command channels. + +- compatible: + Usage: required + Value type: <string> + Definition: must be: "qcom,wcnss", + +- qcom,smd-channel: + Usage: required + Value type: <string> + Definition: standard SMD property specifying the SMD channel used for + communication with the WiFi firmware. + Should be "WCNSS_CTRL". + +- qcom,mmio: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to a node specifying the wcnss "ccu" and "dxe" + register blocks. The node must be compatible with one of + the following: + "qcom,riva", + "qcom,pronto" + += SUBNODES +The subnodes of the wcnss node are optional and describe the individual blocks in +the WCNSS. + +== Bluetooth +The following properties are defined to the bluetooth node: + +- compatible: + Usage: required + Value type: <string> + Definition: must be: + "qcom,wcnss-bt" + +== WiFi +The following properties are defined to the WiFi node: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,wcnss-wlan", + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the "rx" and "tx" interrupts + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must contain "rx" and "tx" + +- qcom,smem-state: + Usage: required + Value type: <prop-encoded-array> + Definition: should reference the tx-enable and tx-rings-empty SMEM states + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must contain "tx-enable" and "tx-rings-empty" + += EXAMPLE +The following example represents a SMD node, with one edge representing the +"pronto" subsystem, with the wcnss device and its wcn3680 BT and WiFi blocks +described; as found on the 8974 platform. + +smd { + compatible = "qcom,smd"; + + pronto-edge { + interrupts = <0 142 1>; + + qcom,ipc = <&apcs 8 17>; + qcom,smd-edge = <6>; + + wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + #address-cells = <1>; + #size-cells = <1>; + + qcom,mmio = <&pronto>; + + bt { + compatible = "qcom,wcnss-bt"; + }; + + wlan { + compatible = "qcom,wcnss-wlan"; + + interrupts = <0 145 0>, <0 146 0>; + interrupt-names = "tx", "rx"; + + qcom,smem-state = <&apps_smsm 10>, <&apps_smsm 9>; + qcom,smem-state-names = "tx-enable", "tx-rings-empty"; + }; + }; + }; +}; + +soc { + pronto: pronto { + compatible = "qcom,pronto"; + + reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>; + reg-names = "ccu", "dxe", "pmu"; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt new file mode 100644 index 000000000000..013e71a2cdc7 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -0,0 +1,35 @@ +* Rockchip General Register Files (GRF) + +The general register file will be used to do static set by software, which +is composed of many registers for system control. + +From RK3368 SoCs, the GRF is divided into two sections, +- GRF, used for general non-secure system, +- PMUGRF, used for always on system + +Required Properties: + +- compatible: GRF should be one of the followings + - "rockchip,rk3066-grf", "syscon": for rk3066 + - "rockchip,rk3188-grf", "syscon": for rk3188 + - "rockchip,rk3228-grf", "syscon": for rk3228 + - "rockchip,rk3288-grf", "syscon": for rk3288 + - "rockchip,rk3368-grf", "syscon": for rk3368 + - "rockchip,rk3399-grf", "syscon": for rk3399 +- compatible: PMUGRF should be one of the followings + - "rockchip,rk3368-pmugrf", "syscon": for rk3368 + - "rockchip,rk3399-pmugrf", "syscon": for rk3399 +- reg: physical base address of the controller and length of memory mapped + region. + +Example: GRF and PMUGRF of RK3399 SoCs + + pmugrf: syscon@ff320000 { + compatible = "rockchip,rk3399-pmugrf", "syscon"; + reg = <0x0 0xff320000 0x0 0x1000>; + }; + + grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon"; + reg = <0x0 0xff770000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 13dc6a3fdb4a..f909ce06afc4 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -7,6 +7,7 @@ Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3368-power-controller" - for RK3368 SoCs. + "rockchip,rk3399-power-controller" - for RK3399 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. Should be 1 for multiple PM domains. - #address-cells: Should be 1. @@ -16,8 +17,18 @@ Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. + "include/dt-bindings/power/rk3399-power.h" - for RK3399 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain switches state. +- pm_qos (optional): phandles to qos blocks which need to be saved and restored + while power domain switches state. + +Qos Example: + + qos_gpu: qos_gpu@ffaf0000 { + compatible ="syscon"; + reg = <0x0 0xffaf0000 0x0 0x20>; + }; Example: @@ -30,6 +41,7 @@ Example: pd_gpu { reg = <RK3288_PD_GPU>; clocks = <&cru ACLK_GPU>; + pm_qos = <&qos_gpu>; }; }; @@ -45,12 +57,41 @@ Example: }; }; +Example 2: + power: power-controller { + compatible = "rockchip,rk3399-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_vio { + #address-cells = <1>; + #size-cells = <0>; + reg = <RK3399_PD_VIO>; + + pd_vo { + #address-cells = <1>; + #size-cells = <0>; + reg = <RK3399_PD_VO>; + + pd_vopb { + reg = <RK3399_PD_VOPB>; + }; + + pd_vopl { + reg = <RK3399_PD_VOPL>; + }; + }; + }; + }; + Node of a device using power domains must have a power-domains property, containing a phandle to the power device node and an index specifying which power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. + "include/dt-bindings/power/rk3399-power.h" - for rk3399 type power domain. Example of the node using power domain: @@ -65,3 +106,9 @@ Example of the node using power domain: power-domains = <&power RK3368_PD_GPU_1>; /* ... */ }; + + node { + /* ... */ + power-domains = <&power RK3399_PD_VOPB>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt index d1ce21a4904d..64c66a5644e7 100644 --- a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -42,7 +42,7 @@ Required properties: - queue-pools : child node classifying the queue ranges into pools. Queue ranges are grouped into 3 type of pools: - qpend : pool of qpend(interruptible) queues - - general-purpose : pool of general queues, primarly used + - general-purpose : pool of general queues, primarily used as free descriptor queues or the transmit DMA queues. - accumulator : pool of queues on PDSP accumulator channel @@ -50,7 +50,7 @@ Required properties: -- qrange : number of queues to use per queue range, specified as <"base queue #" "# of queues">. -- interrupts : Optional property to specify the interrupt mapping - for interruptible queues. The driver additionaly sets + for interruptible queues. The driver additionally sets the interrupt affinity hint based on the cpu mask. -- qalloc-by-id : Optional property to specify that the queues in this range can only be allocated by queue id. @@ -80,7 +80,7 @@ Required properties: latency : time to delay the interrupt, specified in microseconds. -- multi-queue : Optional property to specify that the channel has to - monitor upto 32 queues starting at the base queue #. + monitor up to 32 queues starting at the base queue #. - descriptor-regions : child node describing the memory regions for keystone navigator packet DMA descriptors. The memory for descriptors will be allocated by the driver. diff --git a/Documentation/devicetree/bindings/sound/adi,adau17x1.txt b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt index 8dbce0e18dda..1447dec28125 100644 --- a/Documentation/devicetree/bindings/sound/adi,adau17x1.txt +++ b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt @@ -13,6 +13,11 @@ Required properties: - reg: The i2c address. Value depends on the state of ADDR0 and ADDR1, as wired in hardware. +Optional properties: + - clock-names: If provided must be "mclk". + - clocks: phandle + clock-specifiers for the clock that provides + the audio master clock for the device. + Examples: #include <dt-bindings/sound/adau17x1.h> @@ -20,5 +25,8 @@ Examples: adau1361@38 { compatible = "adi,adau1761"; reg = <0x38>; + + clock-names = "mclk"; + clocks = <&audio_clock>; }; }; diff --git a/Documentation/devicetree/bindings/sound/adi,adau7002.txt b/Documentation/devicetree/bindings/sound/adi,adau7002.txt new file mode 100644 index 000000000000..f144ee1abf85 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau7002.txt @@ -0,0 +1,19 @@ +Analog Devices ADAU7002 Stereo PDM-to-I2S/TDM Converter + +Required properties: + + - compatible: Must be "adi,adau7002" + +Optional properties: + + - IOVDD-supply: Phandle and specifier for the power supply providing the IOVDD + supply as covered in Documentation/devicetree/bindings/regulator/regulator.txt + + If this property is not present it is assumed that the supply pin is + hardwired to always on. + +Example: + adau7002: pdm-to-i2s { + compatible = "adi,adau7002"; + IOVDD-supply = <&supply>; + }; diff --git a/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt new file mode 100644 index 000000000000..b139e66d2a11 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt @@ -0,0 +1,67 @@ +BROADCOM Cygnus Audio I2S/TDM/SPDIF controller + +Required properties: + - compatible : "brcm,cygnus-audio" + - #address-cells: 32bit valued, 1 cell. + - #size-cells: 32bit valued, 0 cell. + - reg : Should contain audio registers location and length + - reg-names: names of the registers listed in "reg" property + Valid names are "aud" and "i2s_in". "aud" contains a + set of DMA, I2S_OUT and SPDIF registers. "i2s_in" contains + a set of I2S_IN registers. + - clocks: PLL and leaf clocks used by audio ports + - assigned-clocks: PLL and leaf clocks + - assigned-clock-parents: parent clocks of the assigned clocks + (usually the PLL) + - assigned-clock-rates: List of clock frequencies of the + assigned clocks + - clock-names: names of 3 leaf clocks used by audio ports + Valid names are "ch0_audio", "ch1_audio", "ch2_audio" + - interrupts: audio DMA interrupt number + +SSP Subnode properties: +- reg: The index of ssp port interface to use + Valid value are 0, 1, 2, or 3 (for spdif) + +Example: + cygnus_audio: audio@180ae000 { + compatible = "brcm,cygnus-audio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x180ae000 0xafd>, <0x180aec00 0x1f8>; + reg-names = "aud", "i2s_in"; + clocks = <&audiopll BCM_CYGNUS_AUDIOPLL_CH0>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH1>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH2>; + assigned-clocks = <&audiopll BCM_CYGNUS_AUDIOPLL>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH0>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH1>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH2>; + assigned-clock-parents = <&audiopll BCM_CYGNUS_AUDIOPLL>; + assigned-clock-rates = <1769470191>, + <0>, + <0>, + <0>; + clock-names = "ch0_audio", "ch1_audio", "ch2_audio"; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + + ssp0: ssp_port@0 { + reg = <0>; + status = "okay"; + }; + + ssp1: ssp_port@1 { + reg = <1>; + status = "disabled"; + }; + + ssp2: ssp_port@2 { + reg = <2>; + status = "disabled"; + }; + + spdif: spdif_port@3 { + reg = <3>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/bt-sco.txt b/Documentation/devicetree/bindings/sound/bt-sco.txt index 29b8e5d40203..641edf75e184 100644 --- a/Documentation/devicetree/bindings/sound/bt-sco.txt +++ b/Documentation/devicetree/bindings/sound/bt-sco.txt @@ -4,7 +4,7 @@ This device support generic Bluetooth SCO link. Required properties: - - compatible : "delta,dfbmcs320" + - compatible : "delta,dfbmcs320" or "linux,bt-sco" Example: diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt new file mode 100644 index 000000000000..acfb47525b49 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l33.txt @@ -0,0 +1,126 @@ +CS35L33 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l33" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : gpio used to reset the amplifier + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L33 are delivered to. + - interrupts : IRQ line info CS35L33. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is + 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with + a value of 1 and will increase at a step size of 100mV until a maximum of + 8000mV. + + - cirrus,ramp-rate : On power up, it affects the time from when the power + up sequence begins to the time the audio reaches a full-scale output. + On power down, it affects the time from when the power-down sequence + begins to when the amplifier disables the PWM outputs. If this property + is not set then soft ramping will be disabled and ramp time would be + 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms, + 60ms,100ms,175ms respectively for 48KHz sample rate. + + - cirrus,boost-ipk : The maximum current allowed for the boost converter. + The range starts at 1850000uA and goes to a maximum of 3600000uA + with a step size of 15625uA. The default is 2500000uA. + + - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON + ADC data word. This property can be set as a value of 0 for bits 15 down + to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8. + + +Optional H/G Algorithm sub-node: + +The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable +the internal H/G Algorithm. + + - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that + controls the amplifier supplies. + +Optional properties for the "cirrus,hg-algo" sub-node: + + - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in + LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory + depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles. + + cirrus,release-rate : The number of consecutive LRCLK periods before + allowing release condition tracking updates. The number of LRCLK periods + start at 3 to a maximum of 255. + + - cirrus,ldo-thld : Configures the signal threshold at which the PWM output + stage enters LDO operation. Starts as a default value of 50mV for a value + of 1 and increases with a step size of 50mV to a maximum of 750mV (value of + 0xF). + + - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G + algorithm uses the max detection path. If not present, the LDO + detection path is used. + + - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G + algorithm switches to the LDO voltage. This property can be set to values + from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms. + The default is 100ms. + + - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg + automatic updating is enabled. + + - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's + reference to the VP voltage for when to start generating a boosted VBST. + The reference voltage starts at 3000mV with a value of 0x3 and is increased + by 100mV per step to a maximum of 5500mV. + + - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is + allowed to increase to a higher voltage when using VPhg automatic + tracking. This property can be set to values from 0 to 3 with rates of 128 + periods, 2048 periods, 32768 periods, and 524288 periods. + The default is 32768 periods. + + - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking + using VPMON. This property can be set to values from 0 to 6 starting at + 1800mV with a step size of 50mV up to a maximum value of 1750mV. + Default is 1800mV. + +Example: + +cs35l33: cs35l33@40 { + compatible = "cirrus,cs35l33"; + reg = <0x40>; + + VA-supply = <&ldo5_reg>; + VP-supply = <&ldo5_reg>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&cs47l91 34 0>; + + cirrus,ramp-rate = <0x0>; + cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */ + cirrus,boost-ipk = <0xE0>; /* 3600mA */ + cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */ + + cirrus,hg-algo { + cirrus,mem-depth = <0x3>; + cirrus,release-rate = <0x3>; + cirrus,ldo-thld = <0x1>; + cirrus,ldo-path-disable = <0x0>; + cirrus,ldo-entry-delay=<0x4>; + cirrus,vp-hg-auto; + cirrus,vp-hg=<0xF>; + cirrus,vp-hg-rate=<0x2>; + cirrus,vp-hg-va=<0x0>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs53l30.txt b/Documentation/devicetree/bindings/sound/cs53l30.txt new file mode 100644 index 000000000000..4dbfb8274cd9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs53l30.txt @@ -0,0 +1,44 @@ +CS53L30 audio CODEC + +Required properties: + + - compatible : "cirrus,cs53l30" + + - reg : the I2C address of the device + + - VA-supply, VP-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. + + - mute-gpios : a GPIO spec for the MUTE pin. The active state can be either + GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW, which would be handled + by the driver automatically. + + - cirrus,micbias-lvl : Set the output voltage level on the MICBIAS Pin. + 0 = Hi-Z + 1 = 1.80 V + 2 = 2.75 V + + - cirrus,use-sdout2 : This is a boolean property. If present, it indicates + the hardware design connects both SDOUT1 and SDOUT2 + pins to output data. Otherwise, it indicates that + only SDOUT1 is connected for data output. + * CS53l30 supports 4-channel data output in the same + * frame using two different ways: + * 1) Normal I2S mode on two data pins -- each SDOUT + * carries 2-channel data in the same time. + * 2) TDM mode on one signle data pin -- SDOUT1 carries + * 4-channel data per frame. + +Example: + +codec: cs53l30@48 { + compatible = "cirrus,cs53l30"; + reg = <0x48>; + reset-gpios = <&gpio 54 0>; + VA-supply = <&cs53l30_va>; + VP-supply = <&cs53l30_vp>; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt new file mode 100644 index 000000000000..55b53e1fd72c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -0,0 +1,51 @@ +Texas Instruments DaVinci McBSP module +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +This binding describes the "Multi-channel Buffered Serial Port" (McBSP) +audio interface found in some TI DaVinci processors like the OMAP-L138 or AM180x. + + +Required properties: +~~~~~~~~~~~~~~~~~~~~ +- compatible : + "ti,da850-mcbsp" : for DA850, AM180x and OPAM-L138 platforms + +- reg : physical base address and length of the controller memory mapped + region(s). +- reg-names : Should contain: + * "mpu" for the main registers (required). + * "dat" for the data FIFO (optional). + +- dmas: three element list of DMA controller phandles, DMA request line and + TC channel ordered triplets. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ +- interrupts : Interrupt numbers for McBSP +- interrupt-names : Known interrupt names are "rx" and "tx" + +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + +Example (AM1808): +~~~~~~~~~~~~~~~~~ + +mcbsp0: mcbsp@1d10000 { + compatible = "ti,da850-mcbsp"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp0_pins>; + + reg = <0x00110000 0x1000>, + <0x00310000 0x1000>; + reg-names = "mpu", "dat"; + interrupts = <97 98>; + interrupts-names = "rx", "tx"; + dmas = <&edma0 3 1 + &edma0 2 1>; + dma-names = "tx", "rx"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/designware-i2s.txt b/Documentation/devicetree/bindings/sound/designware-i2s.txt index 7bb54247f8e8..6a536d570e29 100644 --- a/Documentation/devicetree/bindings/sound/designware-i2s.txt +++ b/Documentation/devicetree/bindings/sound/designware-i2s.txt @@ -12,6 +12,10 @@ Required properties: one for receive. - dma-names : "tx" for the transmit channel, "rx" for the receive channel. +Optional properties: + - interrupts: The interrupt line number for the I2S controller. Add this + parameter if the I2S controller that you are using does not support DMA. + For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties please check: * resource-names.txt diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt index ceaef5126989..f749e2744824 100644 --- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -58,7 +58,7 @@ Required properties: * DMIC (stands for Digital Microphone Jack) Note: The "Mic Jack" and "AMIC" are redundant while - coexsiting in order to support the old bindings + coexisting in order to support the old bindings of wm8962 and sgtl5000. Optional properties: diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 044e5d76e2dd..740b467adf7d 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,8 +7,8 @@ codec/DSP interfaces. Required properties: - - compatible : Compatible list, contains "fsl,vf610-sai" or - "fsl,imx6sx-sai". + - compatible : Compatible list, contains "fsl,vf610-sai", + "fsl,imx6sx-sai" or "fsl,imx6ul-sai" - reg : Offset and length of the register set for the device. @@ -48,6 +48,11 @@ Required properties: receive data by following their own bit clocks and frame sync clocks separately. +Optional properties (for mx6ul): + + - fsl,sai-mclk-direction-output: This is a boolean property. If present, + indicates that SAI will output the SAI MCLK clock. + Note: - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the default synchronous mode (sync Rx with Tx) will be used, which means both diff --git a/Documentation/devicetree/bindings/sound/max98371.txt b/Documentation/devicetree/bindings/sound/max98371.txt new file mode 100644 index 000000000000..6c285235e64b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98371.txt @@ -0,0 +1,17 @@ +max98371 codec + +This device supports I2C mode only. + +Required properties: + +- compatible : "maxim,max98371" +- reg : The chip select number on the I2C bus + +Example: + +&i2c { + max98371: max98371@0x31 { + compatible = "maxim,max98371"; + reg = <0x31>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/max98504.txt b/Documentation/devicetree/bindings/sound/max98504.txt new file mode 100644 index 000000000000..583ed5fdfb28 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98504.txt @@ -0,0 +1,44 @@ +Maxim MAX98504 class D mono speaker amplifier + +This device supports I2C control interface and an IRQ output signal. It features +a PCM and PDM digital audio interface (DAI) and a differential analog input. + +Required properties: + + - compatible : "maxim,max98504" + - reg : should contain the I2C slave device address + - DVDD-supply, DIOVDD-supply, PVDD-supply: power supplies for the device, + as covered in ../regulator/regulator.txt + - interrupts : should specify the interrupt line the device is connected to, + as described in ../interrupt-controller/interrupts.txt + +Optional properties: + + - maxim,brownout-threshold - the PVDD brownout threshold, the value must be + from 0, 1...21 range, corresponding to 2.6V, 2.65V...3.65V voltage range + - maxim,brownout-attenuation - the brownout attenuation to the speaker gain + applied during the "attack hold" and "timed hold" phase, the value must be + from 0...6 (dB) range + - maxim,brownout-attack-hold-ms - the brownout attack hold phase time in ms, + 0...255 (VBATBROWN_ATTK_HOLD, register 0x0018) + - maxim,brownout-timed-hold-ms - the brownout timed hold phase time in ms, + 0...255 (VBATBROWN_TIME_HOLD, register 0x0019) + - maxim,brownout-release-rate-ms - the brownout release phase step time in ms, + 0...255 (VBATBROWN_RELEASE, register 0x001A) + +The default value when the above properties are not specified is 0, +the maxim,brownout-threshold property must be specified to actually enable +the PVDD brownout protection. + +Example: + + max98504@31 { + compatible = "maxim,max98504"; + reg = <0x31>; + interrupt-parent = <&gpio_bank_0>; + interrupts = <2 0>; + + DVDD-supply = <®ulator>; + DIOVDD-supply = <®ulator>; + PVDD-supply = <®ulator>; +}; diff --git a/Documentation/devicetree/bindings/sound/max9860.txt b/Documentation/devicetree/bindings/sound/max9860.txt new file mode 100644 index 000000000000..e0d4e95e31b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max9860.txt @@ -0,0 +1,28 @@ +MAX9860 Mono Audio Voice Codec + +Required properties: + + - compatible : "maxim,max9860" + + - reg : the I2C address of the device + + - AVDD-supply, DVDD-supply and DVDDIO-supply : power supplies for + the device, as covered in bindings/regulator/regulator.txt + + - clock-names : Required element: "mclk". + + - clocks : A clock specifier for the clock connected as MCLK. + +Examples: + + max9860: max9860@10 { + compatible = "maxim,max9860"; + reg = <0x10>; + + AVDD-supply = <®_1v8>; + DVDD-supply = <®_1v8>; + DVDDIO-supply = <®_3v0>; + + clock-names = "mclk"; + clocks = <&pck2>; + }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt new file mode 100644 index 000000000000..3e623a724e55 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -0,0 +1,150 @@ +Mediatek AFE PCM controller for mt2701 + +Required properties: +- compatible = "mediatek,mt2701-audio"; +- reg: register location and size +- interrupts: Should contain AFE interrupt +- clock-names: should have these clock names: + "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_mux1_div", + "top_audio_mux2_div", + "top_audio_48k_timing", + "top_audio_44k_timing", + "top_audpll_mux_sel", + "top_apll_sel", + "top_aud1_pll_98M", + "top_aud2_pll_90M", + "top_hadds2_pll_98M", + "top_hadds2_pll_294M", + "top_audpll", + "top_audpll_d4", + "top_audpll_d8", + "top_audpll_d16", + "top_audpll_d24", + "top_audintbus_sel", + "clk_26m", + "top_syspll1_d4", + "top_aud_k1_src_sel", + "top_aud_k2_src_sel", + "top_aud_k3_src_sel", + "top_aud_k4_src_sel", + "top_aud_k5_src_sel", + "top_aud_k6_src_sel", + "top_aud_k1_src_div", + "top_aud_k2_src_div", + "top_aud_k3_src_div", + "top_aud_k4_src_div", + "top_aud_k5_src_div", + "top_aud_k6_src_div", + "top_aud_i2s1_mclk", + "top_aud_i2s2_mclk", + "top_aud_i2s3_mclk", + "top_aud_i2s4_mclk", + "top_aud_i2s5_mclk", + "top_aud_i2s6_mclk", + "top_asm_m_sel", + "top_asm_h_sel", + "top_univpll2_d4", + "top_univpll2_d2", + "top_syspll_d5"; + +Example: + + afe: mt2701-afe-pcm@11220000 { + compatible = "mediatek,mt2701-audio"; + reg = <0 0x11220000 0 0x2000>, + <0 0x112A0000 0 0x20000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AUDIO>, + <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_MUX1_DIV>, + <&topckgen CLK_TOP_AUD_MUX2_DIV>, + <&topckgen CLK_TOP_AUD_48K_TIMING>, + <&topckgen CLK_TOP_AUD_44K_TIMING>, + <&topckgen CLK_TOP_AUDPLL_MUX_SEL>, + <&topckgen CLK_TOP_APLL_SEL>, + <&topckgen CLK_TOP_AUD1PLL_98M>, + <&topckgen CLK_TOP_AUD2PLL_90M>, + <&topckgen CLK_TOP_HADDS2PLL_98M>, + <&topckgen CLK_TOP_HADDS2PLL_294M>, + <&topckgen CLK_TOP_AUDPLL>, + <&topckgen CLK_TOP_AUDPLL_D4>, + <&topckgen CLK_TOP_AUDPLL_D8>, + <&topckgen CLK_TOP_AUDPLL_D16>, + <&topckgen CLK_TOP_AUDPLL_D24>, + <&topckgen CLK_TOP_AUDINTBUS_SEL>, + <&clk26m>, + <&topckgen CLK_TOP_SYSPLL1_D4>, + <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K5_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K6_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K5_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K6_SRC_DIV>, + <&topckgen CLK_TOP_AUD_I2S1_MCLK>, + <&topckgen CLK_TOP_AUD_I2S2_MCLK>, + <&topckgen CLK_TOP_AUD_I2S3_MCLK>, + <&topckgen CLK_TOP_AUD_I2S4_MCLK>, + <&topckgen CLK_TOP_AUD_I2S5_MCLK>, + <&topckgen CLK_TOP_AUD_I2S6_MCLK>, + <&topckgen CLK_TOP_ASM_M_SEL>, + <&topckgen CLK_TOP_ASM_H_SEL>, + <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_UNIVPLL2_D2>, + <&topckgen CLK_TOP_SYSPLL_D5>; + + clock-names = "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_mux1_div", + "top_audio_mux2_div", + "top_audio_48k_timing", + "top_audio_44k_timing", + "top_audpll_mux_sel", + "top_apll_sel", + "top_aud1_pll_98M", + "top_aud2_pll_90M", + "top_hadds2_pll_98M", + "top_hadds2_pll_294M", + "top_audpll", + "top_audpll_d4", + "top_audpll_d8", + "top_audpll_d16", + "top_audpll_d24", + "top_audintbus_sel", + "clk_26m", + "top_syspll1_d4", + "top_aud_k1_src_sel", + "top_aud_k2_src_sel", + "top_aud_k3_src_sel", + "top_aud_k4_src_sel", + "top_aud_k5_src_sel", + "top_aud_k6_src_sel", + "top_aud_k1_src_div", + "top_aud_k2_src_div", + "top_aud_k3_src_div", + "top_aud_k4_src_div", + "top_aud_k5_src_div", + "top_aud_k6_src_div", + "top_aud_i2s1_mclk", + "top_aud_i2s2_mclk", + "top_aud_i2s3_mclk", + "top_aud_i2s4_mclk", + "top_aud_i2s5_mclk", + "top_aud_i2s6_mclk", + "top_asm_m_sel", + "top_asm_h_sel", + "top_univpll2_d4", + "top_univpll2_d2", + "top_syspll_d5"; + }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt b/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt new file mode 100644 index 000000000000..05574446ceb6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt @@ -0,0 +1,43 @@ +MT2701 with CS42448 CODEC + +Required properties: +- compatible: "mediatek,mt2701-cs42448-machine" +- mediatek,platform: the phandle of MT2701 ASoC platform +- audio-routing: a list of the connections between audio +- mediatek,audio-codec: the phandles of cs42448 codec +- mediatek,audio-codec-bt-mrg the phandles of bt-sco dummy codec +- pinctrl-names: Should contain only one value - "default" +- pinctrl-0: Should specify pin control groups used for this controller. +- i2s1-in-sel-gpio1, i2s1-in-sel-gpio2: Should specify two gpio pins to + control I2S1-in mux. + +Example: + + sound:sound { + compatible = "mediatek,mt2701-cs42448-machine"; + mediatek,platform = <&afe>; + /* CS42448 Machine name */ + audio-routing = + "Line Out Jack", "AOUT1L", + "Line Out Jack", "AOUT1R", + "Line Out Jack", "AOUT2L", + "Line Out Jack", "AOUT2R", + "Line Out Jack", "AOUT3L", + "Line Out Jack", "AOUT3R", + "Line Out Jack", "AOUT4L", + "Line Out Jack", "AOUT4R", + "AIN1L", "AMIC", + "AIN1R", "AMIC", + "AIN2L", "Tuner In", + "AIN2R", "Tuner In", + "AIN3L", "Satellite Tuner In", + "AIN3R", "Satellite Tuner In", + "AIN3L", "AUX In", + "AIN3R", "AUX In"; + mediatek,audio-codec = <&cs42448>; + mediatek,audio-codec-bt-mrg = <&bt_sco_codec>; + pinctrl-names = "default"; + pinctrl-0 = <&aud_pins_default>; + i2s1-in-sel-gpio1 = <&pio 53 0>; + i2s1-in-sel-gpio2 = <&pio 54 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt index f205ce9e31dd..ac28cdb4910e 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt @@ -1,15 +1,16 @@ -MT8173 with RT5650 RT5676 CODECS +MT8173 with RT5650 RT5676 CODECS and HDMI via I2S Required properties: - compatible : "mediatek,mt8173-rt5650-rt5676" - mediatek,audio-codec: the phandles of rt5650 and rt5676 codecs + and of the hdmi encoder node - mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-rt5650-rt5676"; - mediatek,audio-codec = <&rt5650 &rt5676>; + mediatek,audio-codec = <&rt5650 &rt5676 &hdmi0>; mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt index fe5a5ef1714d..29dce2ac8773 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt @@ -1,15 +1,31 @@ -MT8173 with RT5650 CODECS +MT8173 with RT5650 CODECS and HDMI via I2S Required properties: - compatible : "mediatek,mt8173-rt5650" - mediatek,audio-codec: the phandles of rt5650 codecs + and of the hdmi encoder node - mediatek,platform: the phandle of MT8173 ASoC platform +Optional subnodes: +- codec-capture : the subnode of rt5650 codec capture +Required codec-capture subnode properties: +- sound-dai: audio codec dai name on capture path + <&rt5650 0> : Default setting. Connect rt5650 I2S1 for capture. (dai_name = rt5645-aif1) + <&rt5650 1> : Connect rt5650 I2S2 for capture. (dai_name = rt5645-aif2) + +- mediatek,mclk: the MCLK source + 0 : external oscillator, MCLK = 12.288M + 1 : internal source from mt8173, MCLK = sampling rate*256 + Example: sound { compatible = "mediatek,mt8173-rt5650"; - mediatek,audio-codec = <&rt5650>; + mediatek,audio-codec = <&rt5650 &hdmi0>; mediatek,platform = <&afe>; + mediatek,mclk = <0>; + codec-capture { + sound-dai = <&rt5650 1>; + }; }; diff --git a/Documentation/devicetree/bindings/sound/nau8810.txt b/Documentation/devicetree/bindings/sound/nau8810.txt new file mode 100644 index 000000000000..05830e477acd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8810.txt @@ -0,0 +1,16 @@ +NAU8810 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8810" + + - reg : the I2C address of the device. + +Example: + +codec: nau8810@1a { + compatible = "nuvoton,nau8810"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt new file mode 100644 index 000000000000..5da7da4ea07a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra audio complex, with SGTL5000 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-sgtl5000" +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the SGTL5000's pins (as documented in its binding), and the jacks + on the board: + + * Headphone Jack + * Line In Jack + * Mic Jack + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the SGTL5000 audio codec. + +Example: + +sound { + compatible = "toradex,tegra-audio-sgtl5000-apalis_t30", + "nvidia,tegra-audio-sgtl5000"; + nvidia,model = "Toradex Apalis T30"; + nvidia,audio-routing = + "Headphone Jack", "HP_OUT", + "LINE_IN", "Line In Jack", + "MIC_IN", "Mic Jack"; + nvidia,i2s-controller = <&tegra_i2s2>; + nvidia,audio-codec = <&sgtl5000>; + clocks = <&tegra_car TEGRA30_CLK_PLL_A>, + <&tegra_car TEGRA30_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA30_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt index 275c6ea356f6..44d27456e8a4 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -15,7 +15,7 @@ Required properties: Example: -hda@0,70030000 { +hda@70030000 { compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda"; reg = <0x0 0x70030000 0x0 0x10000>; interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/pcm5102a.txt b/Documentation/devicetree/bindings/sound/pcm5102a.txt new file mode 100644 index 000000000000..c63ab0b6ee19 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm5102a.txt @@ -0,0 +1,13 @@ +PCM5102a audio CODECs + +These devices does not use I2C or SPI. + +Required properties: + + - compatible : set as "ti,pcm5102a" + +Examples: + + pcm5102a: pcm5102a { + compatible = "ti,pcm5102a"; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index 48129368d4d9..d9d8635ff94c 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -16,6 +16,24 @@ Required properties: * "spkr-iomux" - qcom,model : Name of the sound card. +- qcom,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, MicBias + of msm8x16_wcd codec and the jacks on the board: + + Power supplies: + * MIC BIAS External1 + * MIC BIAS External2 + * MIC BIAS Internal1 + * MIC BIAS Internal2 + + Board connectors: + * Headset Mic + * Secondary Mic", + * DMIC + * Ext Spk + Dai-link subnode properties and subnodes: Required dai-link subnodes: @@ -37,6 +55,18 @@ sound: sound { reg-names = "mic-iomux", "spkr-iomux"; qcom,model = "DB410c"; + qcom,audio-routing = + "MIC BIAS External1", "Handset Mic", + "MIC BIAS Internal2", "Headset Mic", + "MIC BIAS External1", "Secondary Mic", + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1", + "DMIC1", "MIC BIAS Internal1", + "MIC BIAS Internal1", "Digital Mic1", + "DMIC2", "MIC BIAS Internal1", + "MIC BIAS Internal1", "Digital Mic2"; + /* I2S - Internal codec */ internal-dai-link@0 { cpu { /* PRIMARY */ diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index c7b29df4a963..15a7316e4c91 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -373,6 +373,8 @@ Optional properties: - #clock-cells : it must be 0 if your system has audio_clkout it must be 1 if your system has audio_clkout0/1/2/3 - clock-frequency : for all audio_clkout0/1/2/3 +- clkout-lr-asynchronous : boolean property. it indicates that audio_clkoutn + is asynchronizes with lr-clock. SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt deleted file mode 100644 index 255ece3043ad..000000000000 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ /dev/null @@ -1,75 +0,0 @@ -Renesas Sampling Rate Convert Sound Card: - -Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC <-> codec. - -Required properties: - -- compatible : "renesas,rsrc-card{,<board>}" - Examples with boards are: - - "renesas,rsrc-card" - - "renesas,rsrc-card,lager" - - "renesas,rsrc-card,koelsch" -Optional properties: - -- card_name : User specified audio sound card name, one string - property. -- cpu : CPU sub-node -- codec : CODEC sub-node - -Optional subnode properties: - -- format : CPU/CODEC common audio format. - "i2s", "right_j", "left_j" , "dsp_a" - "dsp_b", "ac97", "pdm", "msb", "lsb" -- frame-master : Indicates dai-link frame master. - phandle to a cpu or codec subnode. -- bitclock-master : Indicates dai-link bit clock master. - phandle to a cpu or codec subnode. -- bitclock-inversion : bool property. Add this if the - dai-link uses bit clock inversion. -- frame-inversion : bool property. Add this if the - dai-link uses frame clock inversion. -- convert-rate : platform specified sampling rate convert -- convert-channels : platform specified converted channel size (2 - 8 ch) -- audio-prefix : see audio-routing -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names for sources. - use audio-prefix if some components is using same sink/sources naming. - it can be used if compatible was "renesas,rsrc-card"; - -Required CPU/CODEC subnodes properties: - -- sound-dai : phandle and port of CPU/CODEC - -Optional CPU/CODEC subnodes properties: - -- clocks / system-clock-frequency : specify subnode's clock if needed. - it can be specified via "clocks" if system has - clock node (= common clock), or "system-clock-frequency" - (if system doens't support common clock) - If a clock is specified, it is - enabled with clk_prepare_enable() - in dai startup() and disabled with - clk_disable_unprepare() in dai - shutdown(). - -Example - -sound { - compatible = "renesas,rsrc-card,lager"; - - card-name = "rsnd-ak4643"; - format = "left_j"; - bitclock-master = <&sndcodec>; - frame-master = <&sndcodec>; - - sndcpu: cpu { - sound-dai = <&rcar_sound>; - }; - - sndcodec: codec { - sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; - }; -}; diff --git a/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt new file mode 100644 index 000000000000..eac91db07178 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt @@ -0,0 +1,22 @@ +ROCKCHIP with MAX98357A/RT5514/DA7219 codecs on GRU boards + +Required properties: +- compatible: "rockchip,rk3399-gru-sound" +- rockchip,cpu: The phandle of the Rockchip I2S controller that's + connected to the codecs +- rockchip,codec: The phandle of the MAX98357A/RT5514/DA7219 codecs + +Optional properties: +- dmic-wakeup-delay-ms : specify delay time (ms) for DMIC ready. + If this option is specified, which means it's required dmic need + delay for DMIC to ready so that rt5514 can avoid recording before + DMIC send valid data + +Example: + +sound { + compatible = "rockchip,rk3399-gru-sound"; + rockchip,cpu = <&i2s0>; + rockchip,codec = <&max98357a &rt5514 &da7219>; + dmic-wakeup-delay-ms = <20>; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 6e86d8aa29b4..4ea29aa9af59 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -23,6 +23,11 @@ Required properties: - rockchip,playback-channels: max playback channels, if not set, 8 channels default. - rockchip,capture-channels: max capture channels, if not set, 2 channels default. +Required properties for controller which support multi channels +playback/capture: + +- rockchip,grf: the phandle of the syscon node for GRF register. + Example for rk3288 I2S controller: i2s@ff890000 { diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index e24436fc5ea9..9cabfc18cb57 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -8,6 +8,11 @@ Required properties: - reg : The I2C address of the device. +Optional properties: + +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/rt5659.txt b/Documentation/devicetree/bindings/sound/rt5659.txt index 5f79e7fde032..1766e0543fc5 100644 --- a/Documentation/devicetree/bindings/sound/rt5659.txt +++ b/Documentation/devicetree/bindings/sound/rt5659.txt @@ -12,6 +12,9 @@ Required properties: Optional properties: +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + - realtek,in1-differential - realtek,in3-differential - realtek,in4-differential diff --git a/Documentation/devicetree/bindings/sound/rt5660.txt b/Documentation/devicetree/bindings/sound/rt5660.txt new file mode 100644 index 000000000000..30be5f921930 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5660.txt @@ -0,0 +1,47 @@ +RT5660 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5660". + +- reg : The I2C address of the device. + +Optional properties: + +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + +- realtek,in1-differential +- realtek,in3-differential + Boolean. Indicate MIC1/3 input are differential, rather than single-ended. + +- realtek,poweroff-in-suspend + Boolean. If the codec will be powered off in suspend, the resume should be + added delay time for waiting codec power ready. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO2 pin as dmic1 data pin + 2: using IN1P pin as dmic1 data pin + +Pins on the device (for linking into audio routes) for RT5660: + + * DMIC L1 + * DMIC R1 + * IN1P + * IN1N + * IN2P + * IN3P + * IN3N + * SPO + * LOUTL + * LOUTR + +Example: + +rt5660 { + compatible = "realtek,rt5660"; + reg = <0x1c>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt new file mode 100644 index 000000000000..7d3c974c6e2e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -0,0 +1,30 @@ +RT5663/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5663" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +Pins on the device (for linking into audio routes) for RT5663/RT5668: + + * IN1P + * IN1N + * IN2P + * IN2N + * HPOL + * HPOR + +Example: + +codec: rt5663@12 { + compatible = "realtek,rt5663"; + reg = <0x12>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt deleted file mode 100644 index 9148f72319e1..000000000000 --- a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt +++ /dev/null @@ -1,35 +0,0 @@ -Samsung Exynos Odroid X2/U3 audio complex with MAX98090 codec - -Required properties: - - compatible : "samsung,odroidx2-audio" - for Odroid X2 board, - "samsung,odroidu3-audio" - for Odroid U3 board - - samsung,model : the user-visible name of this sound complex - - samsung,i2s-controller : the phandle of the I2S controller - - samsung,audio-codec : the phandle of the MAX98090 audio codec - - samsung,audio-routing : a list of the connections between audio - components; each entry is a pair of strings, the first being the - connection's sink, the second being the connection's source; - valid names for sources and sinks are the MAX98090's pins (as - documented in its binding), and the jacks on the board - For Odroid X2: - * Headphone Jack - * Mic Jack - * DMIC - - For Odroid U3: - * Headphone Jack - * Speakers - -Example: - -sound { - compatible = "samsung,odroidu3-audio"; - samsung,i2s-controller = <&i2s0>; - samsung,audio-codec = <&max98090>; - samsung,model = "Odroid-X2"; - samsung,audio-routing = - "Headphone Jack", "HPL", - "Headphone Jack", "HPR", - "IN1", "Mic Jack", - "Mic Jack", "MICBIAS"; -}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 0e5e4eb3ef1b..5666da7b8605 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -7,6 +7,14 @@ Required properties: - clocks : the clock provider of SYS_MCLK +- VDDA-supply : the regulator provider of VDDA + +- VDDIO-supply: the regulator provider of VDDIO + +Optional properties: + +- VDDD-supply : the regulator provider of VDDD + - micbias-resistor-k-ohms : the bias resistor to be used in kOmhs The resistor can take values of 2k, 4k or 8k. If set to 0 it will be off. @@ -15,17 +23,9 @@ Required properties: - micbias-voltage-m-volts : the bias voltage to be used in mVolts The voltage can take values from 1.25V to 3V by 250mV steps - If this node is not mentionned or the value is unknown, then + If this node is not mentioned or the value is unknown, then the value is set to 1.25V. -- VDDA-supply : the regulator provider of VDDA - -- VDDIO-supply: the regulator provider of VDDIO - -Optional properties: - -- VDDD-supply : the regulator provider of VDDD - Example: codec: sgtl5000@0a { diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index cf3979eb3578..c7a93931fad2 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -22,6 +22,8 @@ Optional properties: headphones are attached. - simple-audio-card,mic-det-gpio : Reference to GPIO that signals when a microphone is attached. +- simple-audio-card,aux-devs : List of phandles pointing to auxiliary devices, such + as amplifiers, to be added to the sound card. Optional subnodes: @@ -30,7 +32,7 @@ Optional subnodes: sub-nodes. This container may be omitted when the card has only one DAI link. See the examples and the - section bellow. + section below. Dai-link subnode properties and subnodes: @@ -162,3 +164,38 @@ sound { }; }; }; + +Example 3 - route audio from IMX6 SSI2 through TLV320DAC3100 codec +through TPA6130A2 amplifier to headphones: + +&i2c0 { + codec: tlv320dac3100@18 { + compatible = "ti,tlv320dac3100"; + ... + } + + amp: tpa6130a2@60 { + compatible = "ti,tpa6130a2"; + ... + } +} + +sound { + compatible = "simple-audio-card"; + ... + simple-audio-card,widgets = + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HPLEFT", + "Headphone Jack", "HPRIGHT", + "LEFTIN", "HPL", + "RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&>; + simple-audio-card,cpu { + sound-dai = <&ssi2>; + }; + simple-audio-card,codec { + sound-dai = <&codec>; + clocks = ... + }; +}; diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt new file mode 100644 index 000000000000..d6fe47ed09af --- /dev/null +++ b/Documentation/devicetree/bindings/sound/simple-scu-card.txt @@ -0,0 +1,110 @@ +ASoC simple SCU Sound Card + +Simple-Card specifies audio DAI connections of SoC <-> codec. + +Required properties: + +- compatible : "simple-scu-audio-card" + "renesas,rsrc-card" + +Optional properties: + +- simple-audio-card,name : User specified audio sound card name, one string + property. +- simple-audio-card,cpu : CPU sub-node +- simple-audio-card,codec : CODEC sub-node + +Optional subnode properties: + +- simple-audio-card,format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- simple-audio-card,frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- simple-audio-card,bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- simple-audio-card,bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- simple-audio-card,frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. +- simple-audio-card,convert-rate : platform specified sampling rate convert +- simple-audio-card,convert-channels : platform specified converted channel size (2 - 8 ch) +- simple-audio-card,prefix : see audio-routing +- simple-audio-card,routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources. + use audio-prefix if some components is using same sink/sources naming. + it can be used if compatible was "renesas,rsrc-card"; + +Required CPU/CODEC subnodes properties: + +- sound-dai : phandle and port of CPU/CODEC + +Optional CPU/CODEC subnodes properties: + +- clocks / system-clock-frequency : specify subnode's clock if needed. + it can be specified via "clocks" if system has + clock node (= common clock), or "system-clock-frequency" + (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). + +Example 1. Sampling Rate Covert + +sound { + compatible = "simple-scu-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + simple-audio-card,convert-rate = <48000>; /* see audio_clk_a */ + + simple-audio-card,prefix = "ak4642"; + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "DAI0 Capture", "ak4642 Capture"; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; +}; + +Example 2. 2 CPU 1 Codec + +sound { + compatible = "renesas,rsrc-card"; + + card-name = "rsnd-ak4643"; + format = "left_j"; + bitclock-master = <&dpcmcpu>; + frame-master = <&dpcmcpu>; + + convert-rate = <48000>; /* see audio_clk_a */ + + audio-prefix = "ak4642"; + audio-routing = "ak4642 Playback", "DAI0 Playback", + "ak4642 Playback", "DAI1 Playback"; + + dpcmcpu: cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + + cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + + codec { + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 028fa1c82f50..745dc62f76ea 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -11,7 +11,9 @@ Documentation/devicetree/bindings/sound/simple-card.txt. --------------------------------------- Required properties: - - compatible: "st,sti-uni-player" or "st,sti-uni-reader" + - compatible: "st,stih407-uni-player-hdmi", "st,stih407-uni-player-pcm-out", + "st,stih407-uni-player-dac", "st,stih407-uni-player-spdif", + "st,stih407-uni-reader-pcm_in", "st,stih407-uni-reader-hdmi", - st,syscfg: phandle to boot-device system configuration registers @@ -33,31 +35,37 @@ Required properties: "tx" for "st,sti-uni-player" compatibility "rx" for "st,sti-uni-reader" compatibility - - version: IP version integrated in SOC. - - - dai-name: DAI name that describes the IP. - Required properties ("st,sti-uni-player" compatibility only): - clocks: CPU_DAI IP clock source, listed in the same order than the CPU_DAI properties. - - uniperiph-id: internal SOC IP instance ID. - - - IP mode: IP working mode depending on associated codec. - "HDMI" connected to HDMI codec IP and IEC HDMI formats. - "SPDIF"connected to SPDIF codec and support SPDIF formats. - "PCM" PCM standard mode for I2S or TDM bus. - Optional properties: - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for external codecs connection. - pinctrl-names: should contain only one value - "default". + - st,tdm-mode: to declare to set TDM mode for unireader and uniplayer IPs. + Only compartible with IPs in charge of the external I2S/TDM bus. + Should be declared depending on associated codec. + Example: - sti_uni_player2: sti-uni-player@2 { - compatible = "st,sti-uni-player"; + sti_uni_player1: sti-uni-player@0x8D81000 { + compatible = "st,stih407-uni-player-hdmi"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_1>; + reg = <0x8D81000 0x158>; + interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; + dmas = <&fdma0 3 0 1>; + dma-names = "tx"; + st,tdm-mode = <1>; + }; + + sti_uni_player2: sti-uni-player@0x8D82000 { + compatible = "st,stih407-uni-player-pcm-out"; status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -65,15 +73,11 @@ Example: reg = <0x8D82000 0x158>; interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; dmas = <&fdma0 4 0 1>; - dai-name = "Uni Player #1 (DAC)"; dma-names = "tx"; - uniperiph-id = <2>; - version = <5>; - mode = "PCM"; }; - sti_uni_player3: sti-uni-player@3 { - compatible = "st,sti-uni-player"; + sti_uni_player3: sti-uni-player@0x8D85000 { + compatible = "st,stih407-uni-player-spdif"; status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -82,14 +86,10 @@ Example: interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; dmas = <&fdma0 7 0 1>; dma-names = "tx"; - dai-name = "Uni Player #1 (PIO)"; - uniperiph-id = <3>; - version = <5>; - mode = "SPDIF"; }; - sti_uni_reader1: sti-uni-reader@1 { - compatible = "st,sti-uni-reader"; + sti_uni_reader1: sti-uni-reader@0x8D84000 { + compatible = "st,stih407-uni-reader-hdmi"; status = "disabled"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -97,8 +97,6 @@ Example: interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; dmas = <&fdma0 6 0 1>; dma-names = "rx"; - dai-name = "Uni Reader #1 (HDMI RX)"; - version = <3>; }; 2) sti-sas-codec: internal audio codec IPs driver @@ -152,4 +150,20 @@ Example of audio card declaration: sound-dai = <&sti_sasg_codec 0>; }; }; + simple-audio-card,dai-link@2 { + /* TDM playback */ + format = "left_j"; + frame-inversion = <1>; + cpu { + sound-dai = <&sti_uni_player1>; + dai-tdm-slot-num = <16>; + dai-tdm-slot-width = <16>; + dai-tdm-slot-tx-mask = + <1 1 1 1 0 0 0 0 0 0 1 1 0 0 1 1>; + }; + + codec { + sound-dai = <&sti_sasg_codec 3>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt new file mode 100644 index 000000000000..7b526ec64991 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -0,0 +1,34 @@ +* Allwinner A10 I2S controller + +The I2S bus (Inter-IC sound bus) is a serial link for digital +audio data transfer between devices in the system. + +Required properties: + +- compatible: should be one of the followings + - "allwinner,sun4i-a10-i2s" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the I2S interrupt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should contain followings: + - "apb" : clock for the I2S bus interface + - "mod" : module clock for the I2S controller +- #sound-dai-cells : Must be equal to 0 + +Example: + +i2s0: i2s@01c22400 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-i2s"; + reg = <0x01c22400 0x400>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&apb0_gates 3>, <&i2s0_clk>; + clock-names = "apb", "mod"; + dmas = <&dma SUN4I_DMA_NORMAL 3>, + <&dma SUN4I_DMA_NORMAL 3>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt index 13503aa505a9..0230c4d20506 100644 --- a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt +++ b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt @@ -9,6 +9,7 @@ Required properties: - compatible : should be one of the following: - "allwinner,sun4i-a10-spdif": for the Allwinner A10 SoC + - "allwinner,sun6i-a31-spdif": for the Allwinner A31 SoC - reg : Offset and length of the register set for the device. @@ -25,6 +26,8 @@ Required properties: "apb" clock for the spdif bus. "spdif" clock for spdif controller. + - resets : reset specifier for the ahb reset (A31 and newer only) + Example: spdif: spdif@01c21000 { diff --git a/Documentation/devicetree/bindings/sound/tas571x.txt b/Documentation/devicetree/bindings/sound/tas571x.txt index 0ac31d8d5ac4..b4959f10b74b 100644 --- a/Documentation/devicetree/bindings/sound/tas571x.txt +++ b/Documentation/devicetree/bindings/sound/tas571x.txt @@ -1,4 +1,4 @@ -Texas Instruments TAS5711/TAS5717/TAS5719 stereo power amplifiers +Texas Instruments TAS5711/TAS5717/TAS5719/TAS5721 stereo power amplifiers The codec is controlled through an I2C interface. It also has two other signals that can be wired up to GPIOs: reset (strongly recommended), and @@ -6,7 +6,11 @@ powerdown (optional). Required properties: -- compatible: "ti,tas5711", "ti,tas5717", or "ti,tas5719" +- compatible: should be one of the following: + - "ti,tas5711", + - "ti,tas5717", + - "ti,tas5719", + - "ti,tas5721" - reg: The I2C address of the device - #sound-dai-cells: must be equal to 0 @@ -25,6 +29,8 @@ Optional properties: - PVDD_B-supply: regulator phandle for the PVDD_B supply (5711) - PVDD_C-supply: regulator phandle for the PVDD_C supply (5711) - PVDD_D-supply: regulator phandle for the PVDD_D supply (5711) +- DRVDD-supply: regulator phandle for the DRVDD supply (5721) +- PVDD-supply: regulator phandle for the PVDD supply (5721) Example: diff --git a/Documentation/devicetree/bindings/sound/tas5720.txt b/Documentation/devicetree/bindings/sound/tas5720.txt new file mode 100644 index 000000000000..806ea7381483 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas5720.txt @@ -0,0 +1,25 @@ +Texas Instruments TAS5720 Mono Audio amplifier + +The TAS5720 serial control bus communicates through the I2C protocol only. The +serial bus is also used for periodic codec fault checking/reporting during +audio playback. For more product information please see the links below: + +http://www.ti.com/product/TAS5720L +http://www.ti.com/product/TAS5720M + +Required properties: + +- compatible : "ti,tas5720" +- reg : I2C slave address +- dvdd-supply : phandle to a 3.3-V supply for the digital circuitry +- pvdd-supply : phandle to a supply used for the Class-D amp and the analog + +Example: + +tas5720: tas5720@6c { + status = "okay"; + compatible = "ti,tas5720"; + reg = <0x6c>; + dvdd-supply = <&vdd_3v3_reg>; + pvdd-supply = <&_supply_reg>; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index eff12be5e789..9340d2ddcc54 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -11,6 +11,7 @@ Required properties: "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP) "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) + "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, @@ -37,9 +38,11 @@ CODEC output pins: * MICBIAS CODEC input pins: - * MIC1LP - * MIC1RP - * MIC1LM + * MIC1LP, devices with ADC + * MIC1RP, devices with ADC + * MIC1LM, devices with ADC + * AIN1, devices without ADC + * AIN2, devices without ADC The pins can be used in referring sound node's audio-routing property. diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt new file mode 100644 index 000000000000..ad7ac80a3841 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt @@ -0,0 +1,233 @@ +Broadcom SPI controller + +The Broadcom SPI controller is a SPI master found on various SOCs, including +BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits +of : + MSPI : SPI master controller can read and write to a SPI slave device + BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration + for flash reads and be configured to do single, double, quad lane + io with 3-byte and 4-byte addressing support. + + Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP. + MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance + of a MSPI master without the BSPI to use with non flash slave devices that + use SPI protocol. + +Required properties: + +- #address-cells: + Must be <1>, as required by generic SPI binding. + +- #size-cells: + Must be <0>, also as required by generic SPI binding. + +- compatible: + Must be one of : + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi" : MSPI+BSPI on Cygnus, NSP + "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi" : NS2 SoCs + +- reg: + Define the bases and ranges of the associated I/O address spaces. + The required range is MSPI controller registers. + +- reg-names: + First name does not matter, but must be reserved for the MSPI controller + register range as mentioned in 'reg' above, and will typically contain + - "bspi_regs": BSPI register range, not required with compatible + "spi-brcmstb-mspi" + - "mspi_regs": MSPI register range is required for compatible strings + - "intr_regs", "intr_status_reg" : Interrupt and status register for + NSP, NS2, Cygnus SoC + +- interrupts + The interrupts used by the MSPI and/or BSPI controller. + +- interrupt-names: + Names of interrupts associated with MSPI + - "mspi_halted" : + - "mspi_done": Indicates that the requested SPI operation is complete. + - "spi_lr_fullness_reached" : Linear read BSPI pipe full + - "spi_lr_session_aborted" : Linear read BSPI pipe aborted + - "spi_lr_impatient" : Linear read BSPI requested when pipe empty + - "spi_lr_session_done" : Linear read BSPI session done + +- clocks: + A phandle to the reference clock for this block. + +Optional properties: + + +- native-endian + Defined when using BE SoC and device uses BE register read/write + +Recommended optional m25p80 properties: +- spi-rx-bus-width: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Examples: + +BRCMSTB SoC Example: + + SPI Master (MSPI+BSPI) for SPI-NOR access: + + spi@f03e3400 { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-qspi"; + reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>; + reg-names = "cs_reg", "mspi", "bspi"; + interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>; + interrupt-parent = <0x1c>; + interrupt-names = "mspi_halted", + "mspi_done", + "spi_lr_overread", + "spi_lr_session_done", + "spi_lr_impatient", + "spi_lr_session_aborted", + "spi_lr_fullness_reached"; + + clocks = <&hif_spi>; + clock-names = "sw_spi"; + + m25p80@0 { + #size-cells = <0x2>; + #address-cells = <0x2>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <0x2625a00>; + spi-cpol; + spi-cpha; + m25p,fast-read; + + flash0.bolt@0 { + reg = <0x0 0x0 0x0 0x100000>; + }; + + flash0.macadr@100000 { + reg = <0x0 0x100000 0x0 0x10000>; + }; + + flash0.nvram@110000 { + reg = <0x0 0x110000 0x0 0x10000>; + }; + + flash0.kernel@120000 { + reg = <0x0 0x120000 0x0 0x400000>; + }; + + flash0.devtree@520000 { + reg = <0x0 0x520000 0x0 0x10000>; + }; + + flash0.splash@530000 { + reg = <0x0 0x530000 0x0 0x80000>; + }; + + flash0@0 { + reg = <0x0 0x0 0x0 0x4000000>; + }; + }; + }; + + + MSPI master for any SPI device : + + spi@f0416000 { + #address-cells = <1>; + #size-cells = <0>; + clocks = <&upg_fixed>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-mspi"; + reg = <0xf0416000 0x180>; + reg-names = "mspi"; + interrupts = <0x14>; + interrupt-parent = <&irq0_aon_intc>; + interrupt-names = "mspi_done"; + }; + +iProc SoC Example: + + qspi: spi@18027200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi"; + reg = <0x18027200 0x184>, + <0x18027000 0x124>, + <0x1811c408 0x004>, + <0x180273a0 0x01c>; + reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = + "spi_lr_fullness_reached", + "spi_lr_session_aborted", + "spi_lr_impatient", + "spi_lr_session_done", + "mspi_done", + "mspi_halted"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + NS2 SoC Example: + + qspi: spi@66470200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi"; + reg = <0x66470200 0x184>, + <0x66470000 0x124>, + <0x67017408 0x004>, + <0x664703a0 0x01c>; + reg-names = "mspi", "bspi", "intr_regs", + "intr_status_reg"; + interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "spi_l1_intr"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + m25p80 node for NSP, NS2 + + &qspi { + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <12500000>; + m25p,fast-read; + spi-cpol; + spi-cpha; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x000a0000>; + }; + + partition@a0000 { + label = "env"; + reg = <0x000a0000 0x00060000>; + }; + + partition@100000 { + label = "system"; + reg = <0x00100000 0x00600000>; + }; + + partition@700000 { + label = "rootfs"; + reg = <0x00700000 0x01900000>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 523341a0e113..8bc95e2fc47f 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -11,7 +11,6 @@ Required properties: - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" @@ -21,6 +20,9 @@ See the clock consumer binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { @@ -29,7 +31,6 @@ ecspi@70010000 { compatible = "fsl,imx51-ecspi"; reg = <0x70010000 0x4000>; interrupts = <36>; - fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ <&gpio3 25 0>; /* GPIO3_25 */ dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; diff --git a/Documentation/devicetree/bindings/spi/jcore,spi.txt b/Documentation/devicetree/bindings/spi/jcore,spi.txt new file mode 100644 index 000000000000..93936d16e139 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/jcore,spi.txt @@ -0,0 +1,34 @@ +J-Core SPI master + +Required properties: + +- compatible: Must be "jcore,spi2". + +- reg: Memory region for registers. + +- #address-cells: Must be 1. + +- #size-cells: Must be 0. + +Optional properties: + +- clocks: If a phandle named "ref_clk" is present, SPI clock speed + programming is relative to the frequency of the indicated clock. + Necessary only if the input clock rate is something other than a + fixed 50 MHz. + +- clock-names: Clock names, one for each phandle in clocks. + +See spi-bus.txt for additional properties not specific to this device. + +Example: + +spi@40 { + compatible = "jcore,spi2"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40 0x8>; + spi-max-frequency = <25000000>; + clocks = <&bus_clk>; + clock-names = "ref_clk"; +} diff --git a/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt new file mode 100644 index 000000000000..79de379f4dc0 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt @@ -0,0 +1,34 @@ +Microchip PIC32 SPI Master controller + +Required properties: +- compatible: Should be "microchip,pic32mzda-spi". +- reg: Address and length of register space for the device. +- interrupts: Should contain all three spi interrupts in sequence + of <fault-irq>, <receive-irq>, <transmit-irq>. +- interrupt-names: Should be "fault", "rx", "tx" in order. +- clocks: Phandle of the clock generating SPI clock on the bus. +- clock-names: Should be "mck0". +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- dmas: Two or more DMA channel specifiers following the convention outlined + in Documentation/devicetree/bindings/dma/dma.txt +- dma-names: Names for the dma channels. There must be at least one channel + named "spi-tx" for transmit and named "spi-rx" for receive. + +Example: + +spi1: spi@1f821000 { + compatible = "microchip,pic32mzda-spi"; + reg = <0x1f821000 0x200>; + interrupts = <109 IRQ_TYPE_LEVEL_HIGH>, + <110 IRQ_TYPE_LEVEL_HIGH>, + <111 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fault", "rx", "tx"; + clocks = <&PBCLK2>; + clock-names = "mck0"; + cs-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + dmas = <&dma 134>, <&dma 135>; + dma-names = "spi-rx", "spi-tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 42d595425dfb..4b1d6e74c744 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -8,11 +8,10 @@ in slave mode. The SPI master node requires the following properties: - #address-cells - number of cells required to define a chip select - address on the SPI bus. + address on the SPI bus. - #size-cells - should be zero. - compatible - name of SPI bus controller following generic names - recommended practice. -- cs-gpios - (optional) gpios chip select. + recommended practice. No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -22,16 +21,17 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. -Optional property: -- num-cs : total number of chipselects +Optional properties: +- cs-gpios - gpios chip select. +- num-cs - total number of chipselects. -If cs-gpios is used the number of chip select will automatically increased -with max(cs-gpios > hw cs) +If cs-gpios is used the number of chip selects will be increased automatically +with max(cs-gpios > hw cs). So if for example the controller has 2 CS lines, and the cs-gpios property looks like this: -cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>; +cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; Then it should be configured so that num_chipselect = 4 with the following mapping: @@ -45,29 +45,30 @@ SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. - compatible - (required) name of SPI device following generic names - recommended practice -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz + recommended practice. +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz. - spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode + inverse clock polarity (CPOL) mode. - spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode + shifted clock phase (CPHA) mode. - spi-cs-high - (optional) Empty property indicating device requires - chip select active high + chip select active high. - spi-3wire - (optional) Empty property indicating device requires - 3-wire mode. + 3-wire mode. - spi-lsb-first - (optional) Empty property indicating device requires LSB first mode. -- spi-tx-bus-width - (optional) The bus width(number of data wires) that +- spi-tx-bus-width - (optional) The bus width (number of data wires) that is used for MOSI. Defaults to 1 if not present. -- spi-rx-bus-width - (optional) The bus width(number of data wires) that +- spi-rx-bus-width - (optional) The bus width (number of data wires) that is used for MISO. Defaults to 1 if not present. - spi-rx-delay-us - (optional) Microsecond delay after a read transfer. - spi-tx-delay-us - (optional) Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 +wires (QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is -only 1(SINGLE), 2(DUAL) and 4(QUAD). +only 1 (SINGLE), 2 (DUAL) and 4 (QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed diff --git a/Documentation/devicetree/bindings/spi/spi-clps711x.txt b/Documentation/devicetree/bindings/spi/spi-clps711x.txt new file mode 100644 index 000000000000..4c3ec13f423f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-clps711x.txt @@ -0,0 +1,33 @@ +Serial Peripheral Interface on Cirrus Logic CL-PS71xx, EP72xx, EP73xx + +Required properties +- #address-cells: must be <1> +- #size-cells: must be <0> +- compatible: should include "cirrus,ep7209-spi" +- reg: Address and length of one register range +- interrupts: one interrupt line +- clocks: One entry, refers to the SPI bus clock +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +An additional register is present in the system controller, +which is assumed to be in the same device tree, with and marked +as compatible with "cirrus,ep7209-syscon3". + +Example: + +spi@80000500 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cirrus,ep7209-spi"; + reg = <0x80000500 0x4>; + interrupts = <15>; + clocks = <&clks CLPS711X_CLK_SPI>; + status = "disabled"; +}; + +syscon3: syscon@80002200 { + compatible = "cirrus,ep7209-syscon3", "syscon"; + reg = <0x80002200 0x40>; +}; + diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index d1e914adcf6e..f5916c92fe91 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -21,7 +21,7 @@ Required properties: IP to the interrupt controller within the SoC. Possible values are 0 and 1. Manual says one of the two possible interrupt lines can be tied to the interrupt controller. Set this - based on a specifc SoC configuration. + based on a specific SoC configuration. - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index fa77f874e321..ff5893d275a2 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -1,7 +1,10 @@ ARM Freescale DSPI controller Required properties: -- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", "fsl,ls2085a-dspi" +- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", + "fsl,ls2085a-dspi" + or + "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. @@ -13,8 +16,7 @@ Required properties: Optional property: - big-endian: If present the dspi device's registers are implemented - in big endian mode, otherwise in native mode(same with CPU), for more - detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + in big endian mode. Optional SPI slave node properties: - fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index bb52a86f3365..dc6d0313324a 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -7,7 +7,7 @@ NOR memories, without DMA support and a 64-byte unified transmit / receive buffer. Required properties: - - compatible: should be "amlogic,meson6-spifc" + - compatible: should be "amlogic,meson6-spifc" or "amlogic,meson-gxbb-spifc" - reg: physical base address and length of the controller registers - clocks: phandle of the input clock for the baud rate generator - #address-cells: should be 1 diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 98bc69815eb3..4f629cc7634a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -8,7 +8,15 @@ Required properties: - "marvell,armada-380-spi", for the Armada 38x SoCs - "marvell,armada-390-spi", for the Armada 39x SoCs - "marvell,armada-xp-spi", for the Armada XP SoCs -- reg : offset and length of the register set for the device +- reg : offset and length of the register set for the device. + This property can optionally have additional entries to configure + the SPI direct access mode that some of the Marvell SoCs support + additionally to the normal indirect access (PIO) mode. The values + for the MBus "target" and "attribute" are defined in the Marvell + SoC "Functional Specifications" Manual in the chapter "Marvell + Core Processor Address Decoding". + The eight register sets following the control registers refer to + chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. Optional properties: - interrupts : Is currently not used. @@ -23,3 +31,42 @@ Example: interrupts = <23>; status = "disabled"; }; + +Example with SPI direct mode support (optionally): + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */ + <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */ + <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */ + <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */ + <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */ + <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */ + <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */ + <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ + <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ + interrupts = <23>; + status = "disabled"; + }; + +To enable the direct mode, the board specific 'ranges' property in the +'soc' node needs to add the entries for the desired SPI controllers +and its chip-selects that are used in the direct mode instead of PIO +mode. Here an example for this (SPI controller 0, device 1 and SPI +controller 1, device 2 are used in direct mode. All other SPI device +are used in the default indirect (PIO) mode): + soc { + /* + * Enable the SPI direct access by configuring an entry + * here in the board-specific ranges property + */ + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */ + <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */ + <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */ + <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */ + +For further information on the MBus bindings, please see the MBus +DT documentation: +Documentation/devicetree/bindings/bus/mvebu-mbus.txt diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 1b14d69d8903..d2ca153614f9 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -6,10 +6,13 @@ and display controllers using the SPI communication interface. Required Properties: - compatible: should be one of the following. - "rockchip,rk3066-spi" for rk3066. - "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. - "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. - "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. + "rockchip,rk3036-spi" for rk3036 SoCS. + "rockchip,rk3066-spi" for rk3066 SoCs. + "rockchip,rk3188-spi" for rk3188 SoCs. + "rockchip,rk3228-spi" for rk3228 SoCS. + "rockchip,rk3288-spi" for rk3288 SoCs. + "rockchip,rk3368-spi" for rk3368 SoCs. + "rockchip,rk3399-spi" for rk3399 SoCs. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 6dbdeb3c361a..49028a4f5df1 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -9,7 +9,8 @@ Required SoC Specific Properties: - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - - samsung,exynos7-spi: for exynos7 platforms + - samsung,exynos5433-spi: for exynos5433 compatible controllers + - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED> - reg: physical base address of the controller and length of memory mapped region. @@ -23,6 +24,15 @@ Required SoC Specific Properties: - dma-names: Names for the dma channels. There must be at least one channel named "tx" for transmit and named "rx" for receive. +- clocks: specifies the clock IDs provided to the SPI controller; they are + required for interacting with the controller itself, for synchronizing the bus + and as I/O clock (the latter is required by exynos5433 and exynos7). + +- clock-names: string names of the clocks in the 'clocks' property; for all the + the devices the names must be "spi", "spi_busclkN" (where N is determined by + "samsung,spi-src-clk"), while Exynos5433 should specify a third clock + "spi_ioclk" for the I/O clock. + Required Board Specific Properties: - #address-cells: should be 1. @@ -40,6 +50,9 @@ Optional Board Specific Properties: - cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) +- no-cs-readback: the CS line is disconnected, therefore the device should not + operate based on CS signalling. + SPI Controller specific data in SPI slave nodes: - The spi slave nodes should provide the following information which is required diff --git a/Documentation/devicetree/bindings/spi/sqi-pic32.txt b/Documentation/devicetree/bindings/spi/sqi-pic32.txt new file mode 100644 index 000000000000..c82d021bce50 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sqi-pic32.txt @@ -0,0 +1,18 @@ +Microchip PIC32 Quad SPI controller +----------------------------------- +Required properties: +- compatible: Should be "microchip,pic32mzda-sqi". +- reg: Address and length of SQI controller register space. +- interrupts: Should contain SQI interrupt. +- clocks: Should contain phandle of two clocks in sequence, one that drives + clock on SPI bus and other that drives SQI controller. +- clock-names: Should be "spi_ck" and "reg_ck" in order. + +Example: + sqi1: spi@1f8e2000 { + compatible = "microchip,pic32mzda-sqi"; + reg = <0x1f8e2000 0x200>; + clocks = <&rootclk REF2CLK>, <&rootclk PB5CLK>; + clock-names = "spi_ck", "reg_ck"; + interrupts = <169 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index cc8304aa64ac..e65fde4a7388 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -19,6 +19,13 @@ Optional properties: - syscon-chipselects: Handle to system control region contains QSPI chipselect register and offset of that register. +NOTE: TI QSPI controller requires different pinmux and IODelay +parameters for Mode-0 and Mode-3 operations, which needs to be set up by +the bootloader (U-Boot). Default configuration only supports Mode-0 +operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be +specified in the slave nodes of TI QSPI controller without appropriate +modification to bootloader. + Example: For am4372: diff --git a/Documentation/devicetree/bindings/sram/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index 227e3a341af1..add48f09015e 100644 --- a/Documentation/devicetree/bindings/sram/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt @@ -51,7 +51,7 @@ sram: sram@5c000000 { compatible = "mmio-sram"; reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ - #adress-cells = <1>; + #address-cells = <1>; #size-cells = <1>; ranges = <0 0x5c000000 0x40000>; diff --git a/Documentation/devicetree/bindings/thermal/tegra-soctherm.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt index 6b68cd150405..edebfa0a985e 100644 --- a/Documentation/devicetree/bindings/thermal/tegra-soctherm.txt +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt @@ -26,10 +26,14 @@ Required properties : of this property. See <dt-bindings/thermal/tegra124-soctherm.h> for a list of valid values when referring to thermal sensors. +Note: +- the "critical" type trip points will be set to SOC_THERM hardware as the +shut down temperature. Once the temperature of this thermal zone is higher +than it, the system will be shutdown or reset by hardware. Example : - soctherm@0,700e2000 { + soctherm@700e2000 { compatible = "nvidia,tegra124-soctherm"; reg = <0x0 0x700e2000 0x0 0x1000>; interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; @@ -51,5 +55,13 @@ Example: referring to thermal sensors : thermal-sensors = <&soctherm TEGRA124_SOCTHERM_SENSOR_CPU>; + + trips { + cpu_shutdown_trip: shutdown-trip { + temperature = <102500>; + hysteresis = <1000>; + type = "critical"; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index e5ee3f159893..a8e52c8ccfcc 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -11,7 +11,6 @@ Required properties: - "renesas,thermal-r8a7791" (R-Car M2-W) - "renesas,thermal-r8a7792" (R-Car V2H) - "renesas,thermal-r8a7793" (R-Car M2-N) - - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". diff --git a/Documentation/devicetree/bindings/thermal/tango-thermal.txt b/Documentation/devicetree/bindings/thermal/tango-thermal.txt new file mode 100644 index 000000000000..212198d4b937 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/tango-thermal.txt @@ -0,0 +1,17 @@ +* Tango Thermal + +The SMP8758 SoC includes 3 instances of this temperature sensor +(in the CPU, video decoder, and PCIe controller). + +Required properties: +- #thermal-sensor-cells: Should be 0 (see thermal.txt) +- compatible: "sigma,smp8758-thermal" +- reg: Address range of the thermal registers + +Example: + + cpu_temp: thermal@920100 { + #thermal-sensor-cells = <0>; + compatible = "sigma,smp8758-thermal"; + reg = <0x920100 12>; + }; diff --git a/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt b/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt new file mode 100644 index 000000000000..d72355502b78 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt @@ -0,0 +1,89 @@ +General Purpose Analog To Digital Converter (ADC) based thermal sensor. + +On some of platforms, thermal sensor like thermistors are connected to +one of ADC channel and sensor resistance is read via voltage across the +sensor resistor. The voltage read across the sensor is mapped to +temperature using voltage-temperature lookup table. + +Required properties: +=================== +- compatible: Must be "generic-adc-thermal". +- temperature-lookup-table: Two dimensional array of Integer; lookup table + to map the relation between ADC value and + temperature. When ADC is read, the value is + looked up on the table to get the equivalent + temperature. + The first value of the each row of array is the + temperature in milliCelsius and second value of + the each row of array is the ADC read value. +- #thermal-sensor-cells: Should be 1. See ./thermal.txt for a description + of this property. + +Example : +#include <dt-bindings/thermal/thermal.h> + +i2c@7000c400 { + ads1015: ads1015@4a { + reg = <0x4a>; + compatible = "ads1015"; + sampling-frequency = <3300>; + #io-channel-cells = <1>; + }; +}; + +tboard_thermistor: thermal-sensor { + compatible = "generic-adc-thermal"; + #thermal-sensor-cells = <0>; + io-channels = <&ads1015 1>; + io-channel-names = "sensor-channel"; + temperature-lookup-table = < (-40000) 2578 + (-39000) 2577 + (-38000) 2576 + (-37000) 2575 + (-36000) 2574 + (-35000) 2573 + (-34000) 2572 + (-33000) 2571 + (-32000) 2569 + (-31000) 2568 + (-30000) 2567 + :::::::::: + 118000 254 + 119000 247 + 120000 240 + 121000 233 + 122000 226 + 123000 220 + 124000 214 + 125000 208>; +}; + +dummy_cool_dev: dummy-cool-dev { + compatible = "dummy-cooling-dev"; + #cooling-cells = <2>; /* min followed by max */ +}; + +thermal-zones { + Tboard { + polling-delay = <15000>; /* milliseconds */ + polling-delay-passive = <0>; /* milliseconds */ + thermal-sensors = <&tboard_thermistor>; + + trips { + therm_est_trip: therm_est_trip { + temperature = <40000>; + type = "active"; + hysteresis = <1000>; + }; + }; + + cooling-maps { + map0 { + trip = <&therm_est_trip>; + cooling-device = <&dummy_cool_dev THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <100>; + }; + + }; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 41b817f7b670..88b6ea1ad290 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -62,7 +62,7 @@ For more examples of cooling devices, refer to the example sections below. Required properties: - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order - Size: one cell to specify minimum and maximum cooling state used + Size: one cell to specify minimum and maximum cooling state used in the reference. The first cell is the minimum cooling state requested and the second cell is the maximum cooling state requested in the reference. @@ -119,7 +119,7 @@ Required properties: Optional property: - contribution: The cooling contribution to the thermal zone of the Type: unsigned referred cooling device at the referred trip point. - Size: one cell The contribution is a ratio of the sum + Size: one cell The contribution is a ratio of the sum of all cooling contributions within a thermal zone. Note: Using the THERMAL_NO_LIMIT (-1UL) constant in the cooling-device phandle @@ -145,7 +145,7 @@ Required properties: Size: one cell - thermal-sensors: A list of thermal sensor phandles and sensor specifier - Type: list of used while monitoring the thermal zone. + Type: list of used while monitoring the thermal zone. phandles + sensor specifier @@ -473,7 +473,7 @@ thermal-zones { <&adc>; /* pcb north */ /* hotspot = 100 * bandgap - 120 * adc + 484 */ - coefficients = <100 -120 484>; + coefficients = <100 -120 484>; trips { ... @@ -502,7 +502,7 @@ from the ADC sensor. The binding would be then: thermal-sensors = <&adc>; /* hotspot = 1 * adc + 6000 */ - coefficients = <1 6000>; + coefficients = <1 6000>; (d) - Board thermal diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt index 27cfc7d7ccd7..8d6e4fd2468e 100644 --- a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt +++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt @@ -9,7 +9,7 @@ Required properties: one) - clocks: phandle to the source clock (usually the AHB clock) -Optionnal properties: +Optional properties: - resets: phandle to a reset controller asserting the timer Example: diff --git a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt index cd55b52548e4..d4c62e7b1714 100644 --- a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt +++ b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X Timer Counter Required properties: -- compatible: Shall contain "cirrus,clps711x-timer". +- compatible: Shall contain "cirrus,ep7209-timer". - reg : Address and length of the register set. - interrupts: The interrupt number of the timer. - clocks : phandle of timer reference clock. @@ -15,14 +15,14 @@ Example: }; timer1: timer@80000300 { - compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer"; reg = <0x80000300 0x4>; interrupts = <8>; clocks = <&clks 5>; }; timer2: timer@80000340 { - compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer"; reg = <0x80000340 0x4>; interrupts = <9>; clocks = <&clks 6>; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt new file mode 100644 index 000000000000..c8c03d700382 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt @@ -0,0 +1,15 @@ +NPS Network Processor + +Required properties: + +- compatible : should be "ezchip,nps400-timer" + +Clocks required for compatible = "ezchip,nps400-timer": +- clocks : Must contain a single entry describing the clock input + +Example: + +timer { + compatible = "ezchip,nps400-timer"; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt b/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt index da2d510cae47..e207c11630af 100644 --- a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt +++ b/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt @@ -2,7 +2,9 @@ MOXA ART timer Required properties: -- compatible : Must be "moxa,moxart-timer" +- compatible : Must be one of: + - "moxa,moxart-timer" + - "aspeed,ast2400-timer" - reg : Should contain registers location and length - interrupts : Should contain the timer interrupt number - clocks : Should contain phandle for the clock that drives the counter diff --git a/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt new file mode 100644 index 000000000000..d191612539e8 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt @@ -0,0 +1,17 @@ +Oxford Semiconductor OXNAS SoCs Family RPS Timer +================================================ + +Required properties: +- compatible: Should be "oxsemi,ox810se-rps-timer" or "oxsemi,ox820-rps-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupts of the two timers +- clocks : The phandle of the timer clock source + +example: + +timer0: timer@200 { + compatible = "oxsemi,ox810se-rps-timer"; + reg = <0x200 0x40>; + clocks = <&rpsclk>; + interrupts = <4 5>; +}; diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt index 87f0b0042bae..a41b184d5538 100644 --- a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt +++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt @@ -1,7 +1,9 @@ -Rockchip rk3288 timer +Rockchip rk timer Required properties: -- compatible: shall be "rockchip,rk3288-timer" +- compatible: shall be one of: + "rockchip,rk3288-timer" - for rk3066, rk3036, rk3188, rk322x, rk3288, rk3368 + "rockchip,rk3399-timer" - for rk3399 - reg: base address of the timer register starting with TIMERS CONTROL register - interrupts: should contain the interrupts for Timer0 - clocks : must contain an entry for each entry in clock-names diff --git a/Documentation/devicetree/bindings/timer/snps,arc-timer.txt b/Documentation/devicetree/bindings/timer/snps,arc-timer.txt new file mode 100644 index 000000000000..4ef024630d61 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,arc-timer.txt @@ -0,0 +1,31 @@ +Synopsys ARC Local Timer with Interrupt Capabilities +- Found on all ARC CPUs (ARC700/ARCHS) +- Can be optionally programmed to interrupt on Limit +- Two idential copies TIMER0 and TIMER1 exist in ARC cores and historically + TIMER0 used as clockevent provider (true for all ARC cores) + TIMER1 used for clocksource (mandatory for ARC700, optional for ARC HS) + +Required properties: + +- compatible : should be "snps,arc-timer" +- interrupts : single Interrupt going into parent intc + (16 for ARCHS cores, 3 for ARC700 cores) +- clocks : phandle to the source clock + +Optional properties: + +- interrupt-parent : phandle to parent intc + +Example: + + timer0 { + compatible = "snps,arc-timer"; + interrupts = <3>; + interrupt-parent = <&core_intc>; + clocks = <&core_clk>; + }; + + timer1 { + compatible = "snps,arc-timer"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt b/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt new file mode 100644 index 000000000000..b6cd1b3922de --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt @@ -0,0 +1,14 @@ +Synopsys ARC Free Running 64-bit Global Timer for ARC HS CPUs +- clocksource provider for SMP SoC + +Required properties: + +- compatible : should be "snps,archs-gfrc" +- clocks : phandle to the source clock + +Example: + + gfrc { + compatible = "snps,archs-gfrc"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt b/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt new file mode 100644 index 000000000000..47bd7a702f3f --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt @@ -0,0 +1,14 @@ +Synopsys ARC Free Running 64-bit Local Timer for ARC HS CPUs +- clocksource provider for UP SoC + +Required properties: + +- compatible : should be "snps,archs-rtc" +- clocks : phandle to the source clock + +Example: + + rtc { + compatible = "snps,arc-rtc"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt new file mode 100644 index 000000000000..71c0777960e9 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt @@ -0,0 +1,26 @@ +* Universal Flash Storage (UFS) DesignWare Host Controller + +DWC_UFS nodes are defined to describe on-chip UFS host controllers and MPHY. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : compatible list must contain the PHY type & version: + "snps,g210-tc-6.00-20bit" + "snps,g210-tc-6.00-40bit" + complemented with the Controller IP version: + "snps,dwc-ufshcd-1.40a" + complemented with the JEDEC version: + "jedec,ufs-1.1" + "jedec,ufs-2.0" + +- reg : <registers mapping> +- interrupts : <interrupt mapping for UFS host controller IRQ> + +Example for a setup using a 1.40a DWC Controller with a 6.00 G210 40-bit TC: + dwc-ufs@d0000000 { + compatible = "snps,g210-tc-6.00-40bit", + "snps,dwc-ufshcd-1.40a", + "jedec,ufs-2.0"; + reg = < 0xd0000000 0x10000 >; + interrupts = < 24 >; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 66f6adf8d44d..a99ed5565b26 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -4,8 +4,8 @@ UFSHC nodes are defined to describe on-chip UFS host controllers. Each UFS controller instance should have its own node. Required properties: -- compatible : must contain "jedec,ufs-1.1", may also list one or more - of the following: +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may + also list one or more of the following: "qcom,msm8994-ufshc" "qcom,msm8996-ufshc" "qcom,ufshc" diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index 5883b73ea1b5..f4262ed60582 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -113,13 +113,13 @@ usb2: gadget@fff78000 { clock-names = "hclk", "pclk"; atmel,vbus-gpio = <&pioB 19 0>; - ep0 { + ep@0 { reg = <0>; atmel,fifo-size = <64>; atmel,nb-banks = <1>; }; - ep1 { + ep@1 { reg = <1>; atmel,fifo-size = <1024>; atmel,nb-banks = <2>; @@ -127,7 +127,7 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep2 { + ep@2 { reg = <2>; atmel,fifo-size = <1024>; atmel,nb-banks = <2>; @@ -135,21 +135,21 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep3 { + ep@3 { reg = <3>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; atmel,can-dma; }; - ep4 { + ep@4 { reg = <4>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; atmel,can-dma; }; - ep5 { + ep@5 { reg = <5>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; @@ -157,7 +157,7 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep6 { + ep@6 { reg = <6>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 1084e2bcbe1c..0e03344e2e8b 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -81,6 +81,8 @@ i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - disable-over-current: disable over current detect +- over-current-active-high: over current signal polarity is high active, + typically over current signal polarity is low active. - external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -93,7 +95,7 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; - gadget-itc-setting = <0x4>; /* 4 micro-frames */ + itc-setting = <0x4>; /* 4 micro-frames */ /* Incremental burst of unspecified length */ ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 20a68bf2b4e7..7d16ebfaa5a1 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -26,7 +26,10 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. -- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. + +Deprecated properties: +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) + in gadget mode. Example: diff --git a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt new file mode 100644 index 000000000000..710b782ccf65 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt @@ -0,0 +1,28 @@ +Cavium SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "cavium,octeon-7130-usb-uctl" + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + uctl@1180069000000 { + compatible = "cavium,octeon-7130-usb-uctl"; + reg = <0x00011800 0x69000000 0x00000000 0x00000100>; + ranges; + #address-cells = <0x00000002>; + #size-cells = <0x00000002>; + refclk-frequency = <0x05f5e100>; + refclk-type-ss = "dlmc_ref_clk0"; + refclk-type-hs = "dlmc_ref_clk0"; + power = <0x00000002 0x00000002 0x00000001>; + xhci@1690000000000 { + compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3"; + reg = <0x00016900 0x00000000 0x00000010 0x00000000>; + interrupt-parent = <0x00000010>; + interrupts = <0x00000009 0x00000004>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index fb2ad0acedbd..e3e6983288e3 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -13,8 +13,8 @@ Optional properties: in the array is expected to be a handle to the USB2/HS PHY and the second element is expected to be a handle to the USB3/SS PHY - phys: from the *Generic PHY* bindings - - phy-names: from the *Generic PHY* bindings - - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" + or "usb3-phy". - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. @@ -38,6 +38,13 @@ Optional properties: - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal to the PHY. + - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection + in PHY P3 power state. + - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists + in GUSB2PHYCFG, specify that USB2 PHY doesn't provide + a free-running PHY clock. + - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power + from P0 to P1/P2/P3 without delay. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold @@ -47,6 +54,8 @@ Optional properties: register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { @@ -54,5 +63,4 @@ dwc3@4a030000 { reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; - tx-fifo-resize; }; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index bba825711873..bfadeb1c3bab 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -11,6 +11,11 @@ Optional properties: "peripheral" and "otg". In case this attribute isn't passed via DT, USB DRD controllers should default to OTG. + - phy_type: tells USB controllers that we want to configure the core to support + a UTMI+ PHY with an 8- or 16-bit interface if UTMI+ is + selected. Valid arguments are "utmi" and "utmi_wide". + In case this isn't passed via DT, USB controllers should + default to HW capability. - otg-rev: tells usb driver the release number of the OTG and EH supplement with which the device and its descriptors are compliant, in binary-coded decimal (i.e. 2.0 is 0200H). This @@ -34,6 +39,7 @@ dwc3@4a030000 { usb-phy = <&usb2_phy>, <&usb3,phy>; maximum-speed = "super-speed"; dr_mode = "otg"; + phy_type = "utmi_wide"; otg-rev = <0x0200>; adp-disable; }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt new file mode 100644 index 000000000000..3eee9e505400 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra xHCI controller +============================ + +The Tegra xHCI controller supports both USB2 and USB3 interfaces exposed by +the Tegra XUSB pad controller. + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb" + - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb" + - Tegra210: "nvidia,tegra210-xusb" +- reg: Must contain the base and length of the xHCI host registers, XUSB FPCI + registers and XUSB IPFS registers. +- reg-names: Must contain the following entries: + - "hcd" + - "fpci" + - "ipfs" +- interrupts: Must contain the xHCI host interrupt and the mailbox interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - xusb_host + - xusb_host_src + - xusb_falcon_src + - xusb_ss + - xusb_ss_src + - xusb_ss_div2 + - xusb_hs_src + - xusb_fs_src + - pll_u_480m + - clk_m + - pll_e +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - xusb_host + - xusb_ss + - xusb_src + Note that xusb_src is the shared reset for xusb_{ss,hs,fs,falcon,host}_src. +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to + configure the USB pads used by the XHCI controller + +For Tegra124 and Tegra132: +- avddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- dvddio-pex-supply: PCIe/USB3 digital logic power supply. Must supply 1.05 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-usb-ss-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-usb-ss-supply: High-voltage PCIe/USB3 power supply. Must supply 3.3 V. +- hvdd-usb-ss-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- dvddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- hvddio-pex-supply: High-voltage PCIe/USB3 power supply. Must supply 1.8 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + +Optional properties: +-------------------- +- phys: Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names: Should include an entry for each PHY used by the controller. The + following PHYs are available: + - Tegra124: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2, + usb3-3 + +Example: +-------- + + usb@0,70090000 { + compatible = "nvidia,tegra124-xusb"; + reg = <0x0 0x70090000 0x0 0x8000>, + <0x0 0x70098000 0x0 0x1000>, + <0x0 0x70099000 0x0 0x1000>; + reg-names = "hcd", "fpci", "ipfs"; + + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_XUSB_HOST>, + <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_SS>, + <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>, + <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>, + <&tegra_car TEGRA124_CLK_PLL_U_480M>, + <&tegra_car TEGRA124_CLK_CLK_M>, + <&tegra_car TEGRA124_CLK_PLL_E>; + clock-names = "xusb_host", "xusb_host_src", "xusb_falcon_src", + "xusb_ss", "xusb_ss_div2", "xusb_ss_src", + "xusb_hs_src", "xusb_fs_src", "pll_u_480m", + "clk_m", "pll_e"; + resets = <&tegra_car 89>, <&tegra_car 156>, <&tegra_car 143>; + reset-names = "xusb_host", "xusb_ss", "xusb_src"; + + nvidia,xusb-padctl = <&padctl>; + + phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* mini-PCIe USB */ + <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* USB A */ + <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>; /* USB A */ + phy-names = "usb2-1", "usb2-2", "usb3-0"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-usb-supply = <&vdd_3v3_lp0>; + avdd-pll-utmip-supply = <&vddio_1v8>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + avdd-usb-ss-pll-supply = <&vdd_1v05_run>; + hvdd-usb-ss-supply = <&vdd_3v3_lp0>; + hvdd-usb-ss-pll-e-supply = <&vdd_3v3_lp0>; + }; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index ca164e71dd50..39acb084bce9 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -59,7 +59,6 @@ Example device nodes: interrupts = <0 205 0x4>; phys = <&hs_phy>, <&ss_phy>; phy-names = "usb2-phy", "usb3-phy"; - tx-fifo-resize; dr_mode = "host"; }; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index b6040563e51a..9e18e000339e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -9,6 +9,7 @@ Required properties: - "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device + - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt new file mode 100644 index 000000000000..0536a938e3ab --- /dev/null +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -0,0 +1,59 @@ +Rockchip SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "ref_clk" Controller reference clk, have to be 24 MHz + "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz + "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS + operation and >= 30MHz for HS operation + "grf_clk" Controller grf clk + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/rockchip,dwc3-usb-phy.txt + +Example device nodes: + + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_0: dwc3@fe800000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; + + usbdrd3_1: usb@fe900000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, + <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_1: dwc3@fe900000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe900000 0x0 0x100000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 19233b7365e1..9df456968596 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -14,7 +14,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" -- resets : phandle + reset specifier pair +- resets : a list of phandle + reset specifier pairs Example: diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 6a17aa85c4d5..966885c636d0 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -4,6 +4,7 @@ Required properties: - compatible: should be one or more of - "generic-xhci" for generic XHCI device + - "marvell,armada3700-xhci" for Armada 37xx SoCs - "marvell,armada-375-xhci" for Armada 375 SoCs - "marvell,armada-380-xhci" for Armada 38x SoCs - "renesas,xhci-r8a7790" for r8a7790 SoC diff --git a/Documentation/devicetree/bindings/usb/usb4604.txt b/Documentation/devicetree/bindings/usb/usb4604.txt new file mode 100644 index 000000000000..82506d17712c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb4604.txt @@ -0,0 +1,19 @@ +SMSC USB4604 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb4604" + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x2d + if I2C is used. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb-hub@2d { + compatible = "smsc,usb4604"; + reg = <0x2d>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt index 3539d4e7d23e..f1e27faf528e 100644 --- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -6,6 +6,7 @@ Required properties: "fsl,imx6q-usbmisc" for imx6q "fsl,vf610-usbmisc" for Vybrid vf610 "fsl,imx6sx-usbmisc" for imx6sx + "fsl,imx7d-usbmisc" for imx7d - reg: Should contain registers location and length Examples: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 86740d4a270d..77e985f21707 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,8 +3,8 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. -abilis Abilis Systems abcn Abracon Corporation +abilis Abilis Systems active-semi Active-Semi International Inc ad Avionic Design GmbH adapteva Adapteva, Inc. @@ -16,22 +16,27 @@ al Annapurna Labs allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. +amazon Amazon.com, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. amlogic Amlogic, Inc. ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. +analogix Analogix Semiconductor, Inc. apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems arm ARM Ltd. armadeus ARMadeus Systems SARL +arrow Arrow Electronics artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. +aspeed ASPEED Technology Inc. atlas Atlas Scientific LLC atmel Atmel Corporation auo AU Optronics Corporation +auvidea Auvidea GmbH avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB @@ -58,6 +63,7 @@ cnxt Conexant Systems, Inc. compulab CompuLab Ltd. cortina Cortina Systems, Inc. cosmic Cosmic Circuits +creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. cypress Cypress Semiconductor Corporation @@ -70,13 +76,18 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +domintech Domintech Co., Ltd. +dptechnics DPTechnics +dragino Dragino Technology Co., Limited ea Embedded Artists AB ebv EBV Elektronik edt Emerging Display Technologies eeti eGalax_eMPIA Technology Inc elan Elan Microelectronic Corp. +embest Shenzhen Embest Technology Co., Ltd. emmicro EM Microelectronic energymicro Silicon Laboratories (formerly Energy Micro AS) +engicam Engicam S.r.l. epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. @@ -86,13 +97,15 @@ eukrea Eukréa Electromatique everest Everest Semiconductor Co. Ltd. everspin Everspin Technologies, Inc. excito Excito +ezchip EZchip Semiconductor fcs Fairchild Semiconductor firefly Firefly focaltech FocalTech Systems Co.,Ltd fsl Freescale Semiconductor ge General Electric Company -GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. +geekbuying GeekBuying gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. geniatech Geniatech, Inc. giantplus Giantplus Technology Co., Ltd. globalscale Globalscale Technologies, Inc. @@ -116,18 +129,22 @@ i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. ifi Ingenieurburo Fur Ic-Technologie (I/F/I) -iom Iomega Corporation img Imagination Technologies Ltd. +infineon Infineon Technologies +inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. +iom Iomega Corporation isee ISEE 2007 S.L. isil Intersil issi Integrated Silicon Solutions Inc. +jdi Japan Display Inc. jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH +keithkoep Keith & Koep GmbH keymile Keymile GmbH kinetic Kinetic Technologies kosagi Sutajio Ko-Usagi PTE Ltd. @@ -137,10 +154,11 @@ lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. lg LG Corporation linux Linux-specific binding -lsi LSI Corp. (LSI Logic) lltc Linear Technology Corporation +lsi LSI Corp. (LSI Logic) marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +meas Measurement Specialties mediatek MediaTek Inc. melexis Melexis N.V. merrii Merrii Technology Co., Ltd. @@ -152,6 +170,7 @@ mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +mqmaker mqmaker Inc. msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. @@ -171,22 +190,25 @@ nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. olimex OLIMEX Ltd. +onion Onion Corporation onnn ON Semiconductor Corp. +ontat On Tat Industrial Company opencores OpenCores.org option Option NV +ORCL Oracle Corporation ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies -ORCL Oracle Corporation +oxsemi Oxford Semiconductor, Ltd. panasonic Panasonic Corporation parade Parade Technologies Inc. pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd +pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA -pixcir PIXCIR MICROELECTRONICS Co., Ltd -pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) +pulsedlight PulsedLight, Inc qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qemu QEMU, a generic and open source machine emulator and virtualizer @@ -198,6 +220,7 @@ raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International raspberrypi Raspberry Pi Foundation +raydium Raydium Semiconductor Corp. realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation richtek Richtek Technology Corporation @@ -213,13 +236,15 @@ sgx SGX Sensortech sharp Sharp Corporation si-en Si-En Technology Ltd. sigma Sigma Designs, Inc. +sii Seiko Instruments, Inc. sil Silicon Image silabs Silicon Laboratories +silead Silead Inc. +silergy Silergy Corp. siliconmitus Silicon Mitus, Inc. simtek -sii Seiko Instruments, Inc. -silergy Silergy Corp. sirf SiRF Technology, Inc. +sis Silicon Integrated Systems Corp. sitronix Sitronix Technology Corporation skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation @@ -231,25 +256,35 @@ sony Sony Corporation spansion Spansion Inc. sprd Spreadtrum Communications Inc. st STMicroelectronics +starry Starry Electronic Technology (ShenZhen) Co., LTD startek Startek ste ST-Ericsson stericsson ST-Ericsson +summit Summit microelectronics +sunchip Shenzhen Sunchip Technology Co., Ltd +SUNW Sun Microsystems, Inc +swir Sierra Wireless syna Synaptics Inc. synology Synology, Inc. -SUNW Sun Microsystems, Inc tbs TBS Technologies +tcg Trusted Computing Group tcl Toby Churchill Ltd. +technexion TechNexion technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility +topeet Topeet toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz +tpk TPK U.S.A. LLC tplink TP-LINK Technologies Co., Ltd. tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited +tyan Tyan Computer Corporation +uniwest United Western Technologies Corp (UniWest) upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. @@ -259,6 +294,7 @@ via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation voipac Voipac Technologies s.r.o. +wd Western Digital Corp. wexler Wexler winbond Winbond Electronics corp. wlf Wolfson Microelectronics @@ -267,7 +303,7 @@ x-powers X-Powers xes Extreme Engineering Solutions (X-ES) xillybus Xillybus Ltd. xlnx Xilinx -zyxel ZyXEL Communications Corp. zarlink Zarlink Semiconductor zii Zodiac Inflight Innovations zte ZTE Corp. +zyxel ZyXEL Communications Corp. diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/video/bridge/anx7814.txt new file mode 100644 index 000000000000..b2a22c28c9b3 --- /dev/null +++ b/Documentation/devicetree/bindings/video/bridge/anx7814.txt @@ -0,0 +1,40 @@ +Analogix ANX7814 SlimPort (Full-HD Transmitter) +----------------------------------------------- + +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter +designed for portable devices. + +Required properties: + + - compatible : "analogix,anx7814" + - reg : I2C address of the device + - interrupt-parent : Should be the phandle of the interrupt controller + that services interrupts for this device + - interrupts : Should contain the INTP interrupt + - hpd-gpios : Which GPIO to use for hpd + - pd-gpios : Which GPIO to use for power down + - reset-gpios : Which GPIO to use for reset + +Optional properties: + + - dvdd10-supply : Regulator for 1.0V digital core power. + - Video port for HDMI input, using the DT bindings defined in [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + anx7814: anx7814@38 { + compatible = "analogix,anx7814"; + reg = <0x38>; + interrupt-parent = <&gpio0>; + interrupts = <99 IRQ_TYPE_LEVEL_LOW>; /* INTP */ + hpd-gpios = <&pio 36 GPIO_ACTIVE_HIGH>; + pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>; + port { + anx7814_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt new file mode 100644 index 000000000000..c5e74d7b4406 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt @@ -0,0 +1,16 @@ +Aspeed Watchdog Timer + +Required properties: + - compatible: must be one of: + - "aspeed,ast2400-wdt" + - "aspeed,ast2500-wdt" + + - reg: physical base address of the controller and length of memory mapped + region + +Example: + + wdt1: watchdog@1e785000 { + compatible = "aspeed,ast2400-wdt"; + reg = <0x1e785000 0x1c>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 8dab6fd024aa..107280ef0025 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -5,10 +5,12 @@ Required properties: - reg : Should contain WDT registers location and length - interrupts : Should contain WDT interrupt -Optional property: +Optional properties: - big-endian: If present the watchdog device's registers are implemented in big endian mode, otherwise in native mode(same with CPU), for more detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. +- fsl,ext-reset-output: If present the watchdog device is configured to + assert its external reset (WDOG_B) instead of issuing a software reset. Examples: diff --git a/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt new file mode 100644 index 000000000000..c7fe36fa739c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt @@ -0,0 +1,16 @@ +Meson GXBB SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson-gxbb-wdt" +- reg : Specifies base physical address and size of the registers. +- clocks : Should be a phandle to the Watchdog clock source, for GXBB the xtal + is the default clock source. + +Example: + +wdt: watchdog@98d0 { + compatible = "amlogic,meson-gxbb-wdt"; + reg = <0 0x98d0 0x0 0x10>; + clocks = <&xtal>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt new file mode 100644 index 000000000000..49485f831373 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt @@ -0,0 +1,19 @@ +* Microchip PIC32 Deadman Timer + +The deadman timer is used to reset the processor in the event of a software +malfunction. It is a free-running instruction fetch timer, which is clocked +whenever an instruction fetch occurs until a count match occurs. + +Required properties: +- compatible: must be "microchip,pic32mzda-dmt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of source clk. Should be <&rootclk PB7CLK>. + +Example: + + watchdog@1f800a00 { + compatible = "microchip,pic32mzda-dmt"; + reg = <0x1f800a00 0x80>; + clocks = <&rootclk PB7CLK>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt new file mode 100644 index 000000000000..f03a29a1b323 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt @@ -0,0 +1,18 @@ +* Microchip PIC32 Watchdog Timer + +When enabled, the watchdog peripheral can be used to reset the device if the +WDT is not cleared periodically in software. + +Required properties: +- compatible: must be "microchip,pic32mzda-wdt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of source clk. Should be <&rootclk LPRCCLK>. + +Example: + + watchdog@1f800800 { + compatible = "microchip,pic32mzda-wdt"; + reg = <0x1f800800 0x200>; + clocks = <&rootclk LPRCCLK>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt index 4726924d034e..41aeaa2ff0f8 100644 --- a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt @@ -7,6 +7,10 @@ Required properties : "qcom,kpss-wdt-msm8960" "qcom,kpss-wdt-apq8064" "qcom,kpss-wdt-ipq8064" + "qcom,kpss-wdt-ipq4019" + "qcom,kpss-timer" + "qcom,scss-timer" + "qcom,kpss-wdt" - reg : shall contain base register location and length - clocks : shall contain the input clock diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt new file mode 100644 index 000000000000..da24e3133417 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -0,0 +1,29 @@ +Renesas Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "renesas,<soctype>-wdt", and + "renesas,rcar-gen3-wdt" as fallback. + Examples with soctypes are: + - "renesas,r8a7795-wdt" (R-Car H3) + - "renesas,r8a7796-wdt" (R-Car M3-W) + + When compatible with the generic version, nodes must list the SoC-specific + version corresponding to the platform first, followed by the generic + version. + +- reg : Should contain WDT registers location and length +- clocks : the clock feeding the watchdog timer. + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds +- power-domains : the power domain the WDT belongs to + +Examples: + + wdt0: watchdog@e6020000 { + compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&cpg>; + timeout-sec = <60>; + }; |