diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 28 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bdd83959019c..80710f0f0448 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -36,7 +36,21 @@ Required properties: Optional properties: - clocks : Must contain a reference to the functional clock. -- num-cs : Total number of chip-selects (default is 1) +- num-cs : Total number of chip selects (default is 1). + Up to 3 native chip selects are supported: + 0: MSIOF_SYNC + 1: MSIOF_SS1 + 2: MSIOF_SS2 + Hardware limitations related to chip selects: + - Native chip selects are always deasserted in + between transfers that are part of the same + message. Use cs-gpios to work around this. + - All slaves using native chip selects must use the + same spi-cs-high configuration. Use cs-gpios to + work around this. + - When using GPIO chip selects, at least one native + chip select must be left unused, as it will be + driven anyway. - dmas : Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index 825c39cae74a..b7f5e86fed22 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -27,7 +27,9 @@ The Meson SPICC is generic SPI controller for general purpose Full-Duplex communications with dedicated 16 words RX/TX PIO FIFOs. Required properties: - - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs. + - compatible: should be: + "amlogic,meson-gx-spicc" on Amlogic GX and compatible SoCs. + "amlogic,meson-axg-spicc" on Amlogic AXG and compatible SoCs - reg: physical base address and length of the controller registers - interrupts: The interrupt specifier - clock-names: Must contain "core" diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index df8ec31f2f07..8434a65fc12a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -18,8 +18,17 @@ Required properties: The eight register sets following the control registers refer to chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. +- clocks : pointers to the reference clocks for this device, the first + one is the one used for the clock on the spi bus, the + second one is optional and is the clock used for the + functional part of the controller + Optional properties: - interrupts : Is currently not used. +- clock-names : names of used clocks, mandatory if the second clock is + used, the name must be "core", and "axi" (the latter + is only for Armada 7K/8K). + Example: spi@10600 { diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt index c7b7856bd528..7bf61efc66c8 100644 --- a/Documentation/devicetree/bindings/spi/spi-xilinx.txt +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -2,7 +2,7 @@ Xilinx SPI controller Device Tree Bindings ------------------------------------------------- Required properties: -- compatible : Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b" +- compatible : Should be "xlnx,xps-spi-2.00.a", "xlnx,xps-spi-2.00.b" or "xlnx,axi-quad-spi-1.00.a" - reg : Physical base address and size of SPI registers map. - interrupts : Property with a value describing the interrupt number. |