diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
94 files changed, 1526 insertions, 104 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt new file mode 100644 index 000000000000..5f3719ab7075 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt @@ -0,0 +1,179 @@ +System Control and Management Interface (SCMI) Message Protocol +---------------------------------------------------------- + +The SCMI is intended to allow agents such as OSPM to manage various functions +that are provided by the hardware platform it is running on, including power +and performance functions. + +This binding is intended to define the interface the firmware implementing +the SCMI as described in ARM document number ARM DUI 0922B ("ARM System Control +and Management Interface Platform Design Document")[0] provide for OSPM in +the device tree. + +Required properties: + +The scmi node with the following properties shall be under the /firmware/ node. + +- compatible : shall be "arm,scmi" +- mboxes: List of phandle and mailbox channel specifiers. It should contain + exactly one or two mailboxes, one for transmitting messages("tx") + and another optional for receiving the notifications("rx") if + supported. +- shmem : List of phandle pointing to the shared memory(SHM) area as per + generic mailbox client binding. +- #address-cells : should be '1' if the device has sub-nodes, maps to + protocol identifier for a given sub-node. +- #size-cells : should be '0' as 'reg' property doesn't have any size + associated with it. + +Optional properties: + +- mbox-names: shall be "tx" or "rx" depending on mboxes entries. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details +about the generic mailbox controller and client driver bindings. + +The mailbox is the only permitted method of calling the SCMI firmware. +Mailbox doorbell is used as a mechanism to alert the presence of a +messages and/or notification. + +Each protocol supported shall have a sub-node with corresponding compatible +as described in the following sections. If the platform supports dedicated +communication channel for a particular protocol, the 3 properties namely: +mboxes, mbox-names and shmem shall be present in the sub-node corresponding +to that protocol. + +Clock/Performance bindings for the clocks/OPPs based on SCMI Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Required properties: +- #clock-cells : Should be 1. Contains the Clock ID value used by SCMI commands. + +Power domain bindings for the power domains based on SCMI Message Protocol +------------------------------------------------------------ + +This binding for the SCMI power domain providers uses the generic power +domain binding[2]. + +Required properties: + - #power-domain-cells : Should be 1. Contains the device or the power + domain ID value used by SCMI commands. + +Sensor bindings for the sensors based on SCMI Message Protocol +-------------------------------------------------------------- +SCMI provides an API to access the various sensors on the SoC. + +Required properties: +- #thermal-sensor-cells: should be set to 1. This property follows the + thermal device tree bindings[3]. + + Valid cell values are raw identifiers (Sensor ID) + as used by the firmware. Refer to platform details + for your implementation for the IDs to use. + +SRAM and Shared Memory for SCMI +------------------------------- + +A small area of SRAM is reserved for SCMI communication between application +processors and SCP. + +The properties should follow the generic mmio-sram description found in [4] + +Each sub-node represents the reserved area for SCMI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,scmi-shmem" for Non-secure SRAM based + shared memory + +[0] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/index.html +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/power/power_domain.txt +[3] Documentation/devicetree/bindings/thermal/thermal.txt +[4] Documentation/devicetree/bindings/sram/sram.txt + +Example: + +sram@50000000 { + compatible = "mmio-sram"; + reg = <0x0 0x50000000 0x0 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x10000>; + + cpu_scp_lpri: scp-shmem@0 { + compatible = "arm,scmi-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-shmem@200 { + compatible = "arm,scmi-shmem"; + reg = <0x200 0x200>; + }; +}; + +mailbox@40000000 { + .... + #mbox-cells = <1>; + reg = <0x0 0x40000000 0x0 0x10000>; +}; + +firmware { + + ... + + scmi { + compatible = "arm,scmi"; + mboxes = <&mailbox 0 &mailbox 1>; + mbox-names = "tx", "rx"; + shmem = <&cpu_scp_lpri &cpu_scp_hpri>; + #address-cells = <1>; + #size-cells = <0>; + + scmi_devpd: protocol@11 { + reg = <0x11>; + #power-domain-cells = <1>; + }; + + scmi_dvfs: protocol@13 { + reg = <0x13>; + #clock-cells = <1>; + }; + + scmi_clk: protocol@14 { + reg = <0x14>; + #clock-cells = <1>; + }; + + scmi_sensors0: protocol@15 { + reg = <0x15>; + #thermal-sensor-cells = <1>; + }; + }; +}; + +cpu@0 { + ... + reg = <0 0>; + clocks = <&scmi_dvfs 0>; +}; + +hdlcd@7ff60000 { + ... + reg = <0 0x7ff60000 0 0x1000>; + clocks = <&scmi_clk 4>; + power-domains = <&scmi_devpd 1>; +}; + +thermal-zones { + soc_thermal { + polling-delay-passive = <100>; + polling-delay = <1000>; + /* sensor ID */ + thermal-sensors = <&scmi_sensors0 3>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp new file mode 100644 index 000000000000..8e043301e28e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp @@ -0,0 +1,42 @@ +========================================================= +Secondary CPU enable-method "nuvoton,npcm750-smp" binding +========================================================= + +To apply to all CPUs, a single "nuvoton,npcm750-smp" enable method should be +defined in the "cpus" node. + +Enable method name: "nuvoton,npcm750-smp" +Compatible machines: "nuvoton,npcm750" +Compatible CPUs: "arm,cortex-a9" +Related properties: (none) + +Note: +This enable method needs valid nodes compatible with "arm,cortex-a9-scu" and +"nuvoton,npcm750-gcr". + +Example: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "nuvoton,npcm750-smp"; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + clocks = <&clk NPCM7XX_CLK_CPU>; + clock-names = "clk_cpu"; + reg = <0>; + next-level-cache = <&L2>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + clocks = <&clk NPCM7XX_CLK_CPU>; + clock-names = "clk_cpu"; + reg = <1>; + next-level-cache = <&L2>; + }; + }; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index f4a777039f03..29e1dc5d506d 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -185,6 +185,7 @@ described below. "nvidia,tegra186-denver" "qcom,krait" "qcom,kryo" + "qcom,kryo385" "qcom,scorpion" - enable-method Value type: <stringlist> @@ -198,6 +199,7 @@ described below. "actions,s500-smp" "allwinner,sun6i-a31" "allwinner,sun8i-a23" + "allwinner,sun9i-a80-smp" "amlogic,meson8-smp" "amlogic,meson8b-smp" "arm,realview-smp" diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt new file mode 100644 index 000000000000..10bd35f9207f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt @@ -0,0 +1,33 @@ +Hisilicon Hip06 Low Pin Count device + Hisilicon Hip06 SoCs implement a Low Pin Count (LPC) controller, which + provides I/O access to some legacy ISA devices. + Hip06 is based on arm64 architecture where there is no I/O space. So, the + I/O ports here are not CPU addresses, and there is no 'ranges' property in + LPC device node. + +Required properties: +- compatible: value should be as follows: + (a) "hisilicon,hip06-lpc" + (b) "hisilicon,hip07-lpc" +- #address-cells: must be 2 which stick to the ISA/EISA binding doc. +- #size-cells: must be 1 which stick to the ISA/EISA binding doc. +- reg: base memory range where the LPC register set is mapped. + +Note: + The node name before '@' must be "isa" to represent the binding stick to the + ISA/EISA binding specification. + +Example: + +isa@a01b0000 { + compatible = "hisilicon,hip06-lpc"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x0 0xa01b0000 0x0 0x1000>; + + ipmi0: bt@e4 { + compatible = "ipmi-bt"; + device_type = "ipmi"; + reg = <0x01 0xe4 0x04>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 91d517849483..7d21ab37c19c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -50,6 +50,15 @@ Supported boards: - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; +- Reference board for MT7623a with eMMC: + Required root node properties: + - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; +- Reference board for MT7623a with NAND: + Required root node properties: + - compatible = "mediatek,mt7623a-rfb-nand", "mediatek,mt7623"; +- Reference board for MT7623n with eMMC: + Required root node properties: + - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; - Reference board for MT7623n with NAND: Required root node properties: - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index 9b8f578d5e19..34a69ba67f13 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -6,6 +6,7 @@ The MediaTek AUDSYS controller provides various clocks to the system. Required Properties: - compatible: Should be one of: + - "mediatek,mt2701-audsys", "syscon" - "mediatek,mt7622-audsys", "syscon" - #clock-cells: Must be 1 @@ -13,10 +14,19 @@ The AUDSYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt The available clocks are defined in dt-bindings/clock/mt*-clk.h. +Required sub-nodes: +------- +For common binding part and usage, refer to +../sonud/mt2701-afe-pcm.txt. + Example: -audsys: audsys@11220000 { - compatible = "mediatek,mt7622-audsys", "syscon"; - reg = <0 0x11220000 0 0x1000>; - #clock-cells = <1>; -}; + audsys: clock-controller@11220000 { + compatible = "mediatek,mt7622-audsys", "syscon"; + reg = <0 0x11220000 0 0x2000>; + #clock-cells = <1>; + + afe: audio-controller { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt index 6cc7840ff37a..8f5335b480ac 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-ethsys", "syscon" - "mediatek,mt7622-ethsys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The ethsys controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt index d5d5f1227665..7fe5dc6097a6 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt7622-pciesys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The PCIESYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -19,4 +20,5 @@ pciesys: pciesys@1a100800 { compatible = "mediatek,mt7622-pciesys", "syscon"; reg = <0 0x1a100800 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt index 00760019da00..b8184da2508c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt7622-ssusbsys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The SSUSBSYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -19,4 +20,5 @@ ssusbsys: ssusbsys@1a000000 { compatible = "mediatek,mt7622-ssusbsys", "syscon"; reg = <0 0x1a000000 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/npcm/npcm.txt b/Documentation/devicetree/bindings/arm/npcm/npcm.txt new file mode 100644 index 000000000000..2d87d9ecea85 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/npcm/npcm.txt @@ -0,0 +1,6 @@ +NPCM Platforms Device Tree Bindings +----------------------------------- +NPCM750 SoC +Required root node properties: + - compatible = "nuvoton,npcm750"; + diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt index ce8dabf8c0f9..f35b77920786 100644 --- a/Documentation/devicetree/bindings/arm/omap/ctrl.txt +++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt @@ -25,6 +25,7 @@ Required properties: "ti,omap4-scm-padconf-wkup" "ti,omap5-scm-core" "ti,omap5-scm-padconf-core" + "ti,omap5-scm-wkup-pad-conf" "ti,dra7-scm-core" - reg: Contains Control Module register address range (base address and length) diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt index 763695db2bd9..f301e636fd52 100644 --- a/Documentation/devicetree/bindings/arm/omap/mpu.txt +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -13,6 +13,13 @@ Required properties: Optional properties: - sram: Phandle to the ocmcram node +am335x and am437x only: +- pm-sram: Phandles to ocmcram nodes to be used for power management. + First should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.txt + for more details. + Examples: - For an OMAP5 SMP system: @@ -36,3 +43,12 @@ mpu { compatible = "ti,omap3-mpu"; ti,hwmods = "mpu"; }; + +- For an AM335x system: + +mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + pm-sram = <&pm_sram_code + &pm_sram_data>; +}; diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 0ed4d39d7fe1..ee532e705d6c 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -26,6 +26,7 @@ The 'SoC' element must be one of the following strings: msm8996 mdm9615 ipq8074 + sdm845 The 'board' element must be one of the following strings: diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 326d24bca1a9..1c1d62d03c4f 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -50,6 +50,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "firefly,firefly-rk3399", "rockchip,rk3399"; +- Firefly roc-rk3328-cc board: + Required root node properties: + - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328"; + - ChipSPARK PopMetal-RK3288 board: Required root node properties: - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; @@ -181,10 +185,18 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; +- Rockchip RK3399 Sapphire board standalone: + Required root node properties: + - compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399"; + - Rockchip RK3399 Sapphire Excavator board: Required root node properties: - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399"; +- Theobroma Systems RK3368-uQ7 Haikou Baseboard: + Required root node properties: + - compatible = "tsd,rk3368-uq7-haikou", "rockchip,rk3368"; + - Theobroma Systems RK3399-Q7 Haikou Baseboard: Required root node properties: - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399"; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index 779f5614bcee..16685787d2bd 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -43,6 +43,12 @@ following properties: - interrupt-parent: a phandle indicating which interrupt controller this PMU signals interrupts to. + +Optional nodes: + +- nodes defining the restart and poweroff syscon children + + Example : pmu_system_controller: system-controller@10040000 { compatible = "samsung,exynos5250-pmu", "syscon"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 469ac98ecf8f..14510b215480 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -9,7 +9,11 @@ Required root node properties: - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. - "samsung,trats" - for Exynos4210-based Tizen Reference board. - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,i9300" - for Exynos4412-based Samsung GT-I9300 board. + - "samsung,i9305" - for Exynos4412-based Samsung GT-I9305 board. + - "samsung,midas" - for Exynos4412-based Samsung Midas board. - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,n710x" - for Exynos4412-based Samsung GT-N7100/GT-N7105 board. - "samsung,trats2" - for Exynos4412-based Tizen Reference board. - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. - "samsung,xyref5260" - for Exynos5260-based Samsung board. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 5c3af7ef0761..d3d1df97834f 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,8 +39,12 @@ SoCs: compatible = "renesas,r8a7795" - R-Car M3-W (R8A77960) compatible = "renesas,r8a7796" + - R-Car M3-N (R8A77965) + compatible = "renesas,r8a77965" - R-Car V3M (R8A77970) compatible = "renesas,r8a77970" + - R-Car V3H (R8A77980) + compatible = "renesas,r8a77980" - R-Car D3 (R8A77995) compatible = "renesas,r8a77995" @@ -52,11 +56,13 @@ Boards: - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA - compatible = "renesas,armadillo800eva" + compatible = "renesas,armadillo800eva", "renesas,r8a7740" - Blanche (RTP0RC7792SEB00010S) compatible = "renesas,blanche", "renesas,r8a7792" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" + - Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01) + compatible = "renesas,condor", "renesas,r8a77980" - Draak (RTP0RC77995SEB0010S) compatible = "renesas,draak", "renesas,r8a77995" - Eagle (RTP0RC77970SEB0010S) @@ -102,19 +108,25 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7795" - Salvator-X (RTP0RC7796SIPB0011S) compatible = "renesas,salvator-x", "renesas,r8a7796" + - Salvator-X (RTP0RC7796SIPB0011S (M3N)) + compatible = "renesas,salvator-x", "renesas,r8a77965" - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7795" - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7796" + - Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S) + compatible = "renesas,salvator-xs", "renesas,r8a77965" - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" - SK-RZG1E (YR8A77450S000BE) compatible = "renesas,sk-rzg1e", "renesas,r8a7745" - SK-RZG1M (YR8A77430S000BE) compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - - V3MSK + - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD) + compatible = "renesas,stout", "renesas,r8a7790" + - V3MSK (Y-ASK-RCAR-V3M-WS10) compatible = "renesas,v3msk", "renesas,r8a77970" - - Wheat + - Wheat (RTP0RC7792ASKB0000JE) compatible = "renesas,wheat", "renesas,r8a7792" diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt index 05762b08a7bb..6808ed9ddfd5 100644 --- a/Documentation/devicetree/bindings/arm/stm32.txt +++ b/Documentation/devicetree/bindings/arm/stm32.txt @@ -7,3 +7,4 @@ using one of the following compatible strings: st,stm32f469 st,stm32f746 st,stm32h743 + st,stm32mp157 diff --git a/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt new file mode 100644 index 000000000000..082e6a9382d3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt @@ -0,0 +1,44 @@ +Allwinner SRAM for smp bringup: +------------------------------------------------ + +Allwinner's A80 SoC uses part of the secure sram for hotplugging of the +primary core (cpu0). Once the core gets powered up it checks if a magic +value is set at a specific location. If it is then the BROM will jump +to the software entry address, instead of executing a standard boot. + +Therefore a reserved section sub-node has to be added to the mmio-sram +declaration. + +Note that this is separate from the Allwinner SRAM controller found in +../../sram/sunxi-sram.txt. This SRAM is secure only and not mappable to +any device. + +Also there are no "secure-only" properties. The implementation should +check if this SRAM is usable first. + +Required sub-node properties: +- compatible : depending on the SoC this should be one of: + "allwinner,sun9i-a80-smp-sram" + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sram.txt + +Example: + + sram_b: sram@20000 { + /* 256 KiB secure SRAM at 0x20000 */ + compatible = "mmio-sram"; + reg = <0x00020000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00020000 0x40000>; + + smp-sram@1000 { + /* + * This is checked by BROM to determine if + * cpu0 should jump to SMP entry vector + */ + compatible = "allwinner,sun9i-a80-smp-sram"; + reg = <0x1000 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 7f1411bbabf7..32f62bb7006d 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -9,6 +9,12 @@ following compatible values: nvidia,tegra20 nvidia,tegra30 + nvidia,tegra114 + nvidia,tegra124 + nvidia,tegra132 + nvidia,tegra210 + nvidia,tegra186 + nvidia,tegra194 Boards ------------------------------------------- @@ -26,8 +32,18 @@ board-specific compatible values: nvidia,cardhu nvidia,cardhu-a02 nvidia,cardhu-a04 + nvidia,dalmore nvidia,harmony + nvidia,jetson-tk1 + nvidia,norrin + nvidia,p2371-0000 + nvidia,p2371-2180 + nvidia,p2571 + nvidia,p2771-0000 + nvidia,p2972-0000 + nvidia,roth nvidia,seaboard + nvidia,tn7 nvidia,ventana toradex,apalis_t30 toradex,apalis_t30-eval diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt index 078a58b0302f..5a3bf7c5a7a0 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt @@ -3,6 +3,7 @@ NVIDIA Tegra Power Management Controller (PMC) Required properties: - compatible: Should contain one of the following: - "nvidia,tegra186-pmc": for Tegra186 + - "nvidia,tegra194-pmc": for Tegra194 - reg: Must contain an (offset, length) pair of the register set for each entry in reg-names. - reg-names: Must include the following entries: @@ -10,6 +11,7 @@ Required properties: - "wake" - "aotag" - "scratch" + - "misc" (Only for Tegra194) Optional properties: - nvidia,invert-interrupt: If present, inverts the PMU interrupt signal. diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt index 1f7995357888..b9043bc35c14 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.txt +++ b/Documentation/devicetree/bindings/arm/xilinx.txt @@ -5,3 +5,59 @@ shall have the following properties. Required root node properties: - compatible = "xlnx,zynq-7000"; + +Additional compatible strings: + +- Xilinx internal board cc108 + "xlnx,zynq-cc108" + +- Xilinx internal board zc770 with different FMC cards + "xlnx,zynq-zc770-xm010" + "xlnx,zynq-zc770-xm011" + "xlnx,zynq-zc770-xm012" + "xlnx,zynq-zc770-xm013" + +- Digilent Zybo Z7 board + "digilent,zynq-zybo-z7" + +--------------------------------------------------------------- + +Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings + +Boards with ZynqMP SOC based on an ARM Cortex A53 processor +shall have the following properties. + +Required root node properties: + - compatible = "xlnx,zynqmp"; + + +Additional compatible strings: + +- Xilinx internal board zc1232 + "xlnx,zynqmp-zc1232-revA", "xlnx,zynqmp-zc1232" + +- Xilinx internal board zc1254 + "xlnx,zynqmp-zc1254-revA", "xlnx,zynqmp-zc1254" + +- Xilinx internal board zc1275 + "xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275" + +- Xilinx internal board zc1751 + "xlnx,zynqmp-zc1751" + +- Xilinx 96boards compatible board zcu100 + "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100" + +- Xilinx evaluation board zcu102 + "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102" + "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102" + "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102" + +- Xilinx evaluation board zcu104 + "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104" + +- Xilinx evaluation board zcu106 + "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106" + +- Xilinx evaluation board zcu111 + "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111" diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt index 3e21eb822811..c1e70621799b 100644 --- a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt @@ -73,7 +73,7 @@ Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the controllers with a simple-bus node since they are all connected to the same chip-select (CS4), in this example external address decoding is provided: -gmi@70090000 { +gmi@70009000 { compatible = "nvidia,tegra20-gmi"; reg = <0x70009000 0x1000>; #address-cells = <2>; @@ -84,7 +84,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - bus@4,0 { compatible = "simple-bus"; #address-cells = <1>; @@ -109,7 +108,7 @@ gmi@70090000 { Example with one SJA1000 CAN controller connected to the GMI bus on CS4: -gmi@70090000 { +gmi@70009000 { compatible = "nvidia,tegra20-gmi"; reg = <0x70009000 0x1000>; #address-cells = <2>; @@ -120,7 +119,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - can@4,0 { reg = <4 0 0x100>; nvidia,snor-mux-mode; diff --git a/Documentation/devicetree/bindings/clock/imx6sll-clock.txt b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt new file mode 100644 index 000000000000..fee849d5fdd1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt @@ -0,0 +1,36 @@ +* Clock bindings for Freescale i.MX6 SLL + +Required properties: +- compatible: Should be "fsl,imx6sll-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sll-clock.h +for the full list of i.MX6 SLL clock IDs. + +Examples: + +#include <dt-bindings/clock/imx6sll-clock.h> + +clks: clock-controller@20c4000 { + compatible = "fsl,imx6sll-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <1>; + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; +}; + +uart1: serial@2020000 { + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, + <&clks IMX6SLL_CLK_UART1_SERIAL>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/intc_stratix10.txt b/Documentation/devicetree/bindings/clock/intc_stratix10.txt new file mode 100644 index 000000000000..9f4ec5cb5c6b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/intc_stratix10.txt @@ -0,0 +1,20 @@ +Device Tree Clock bindings for Intel's SoCFPGA Stratix10 platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be + "intel,stratix10-clkmgr" + +- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. + +- #clock-cells : from common clock binding, shall be set to 1. + +Example: + clkmgr: clock-controller@ffd10000 { + compatible = "intel,stratix10-clkmgr"; + reg = <0xffd10000 0x1000>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index f1890d0777a6..773a5226342f 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -22,7 +22,9 @@ Required Properties: - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) + - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR @@ -32,8 +34,8 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796, r8a77970, r8a77995) - - "extalr" (r8a7795, r8a7796, r8a77970) + r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995) + - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) - #clock-cells: Must be 2 diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt index e71c675ba5da..904ae682ea90 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -32,6 +32,7 @@ clock-output-names: - "clkin_i2s" - external I2S clock - optional, - "gmac_clkin" - external GMAC clock - optional - "phy_50m_out" - output clock of the pll in the mac phy + - "hdmi_phy" - output clock of the hdmi phy pll - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt new file mode 100644 index 000000000000..b86535b80920 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt @@ -0,0 +1,25 @@ +Binding for Silicon Labs 544 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si544 datasheet + https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf + +Required properties: + - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according + to the speed grade of the chip. + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si544". + +Example: + si544: clock-controller@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si544b"; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt new file mode 100644 index 000000000000..fb9495ea582c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt @@ -0,0 +1,60 @@ +STMicroelectronics STM32 Peripheral Reset Clock Controller +========================================================== + +The RCC IP is both a reset and a clock controller. + +RCC makes also power management (resume/supend and wakeup interrupt). + +Please also refer to reset.txt for common reset controller binding usage. + +Please also refer to clock-bindings.txt for common clock controller +binding usage. + + +Required properties: +- compatible: "st,stm32mp1-rcc", "syscon" +- reg: should be register base and length as documented in the datasheet +- #clock-cells: 1, device nodes should specify the clock in their + "clocks" property, containing a phandle to the clock device node, + an index specifying the clock to use. +- #reset-cells: Shall be 1 +- interrupts: Should contain a general interrupt line and a interrupt line + to the wake-up of processor (CSTOP). + +Example: + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>, + <GIC_SPI 145 IRQ_TYPE_NONE>; + }; + +Specifying clocks +================= + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/stm32mp1-clks.h header and can be used in device +tree sources. + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example on STM32MP1, for LTDC reset: + ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset + = 0x180 / 4 * 32 + 0 = 3072 + +The list of valid indices for STM32MP1 is available in: +include/dt-bindings/reset-controller/stm32mp1-resets.h + +This file implements defines like: +#define LTDC_R 3072 diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 4ca21c3a6fc9..460ef27b1008 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -20,6 +20,7 @@ Required properties : - "allwinner,sun50i-a64-ccu" - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" + - "allwinner,sun50i-h6-ccu" - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length @@ -31,6 +32,9 @@ Required properties : - #clock-cells : must contain 1 - #reset-cells : must contain 1 +For the main CCU on H6, one more clock is needed: +- "iosc": the SoC's internal frequency oscillator + For the PRCM CCUs on A83T/H3/A64, two more clocks are needed: - "pll-periph": the SoC's peripheral PLL from the main CCU - "iosc": the SoC's internal frequency oscillator diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt new file mode 100644 index 000000000000..1e03dce99a8f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt @@ -0,0 +1,93 @@ +Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks + +TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of +registers call CFGCHIPn. Some of these registers function as clock +gates. This document describes the bindings for those clocks. + +All of the clock nodes described below must be child nodes of a CFGCHIP node +(compatible = "ti,da830-cfgchip"). + +USB PHY clocks +-------------- +Required properties: +- compatible: shall be "ti,da830-usb-phy-clocks". +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "fck", "usb_refclkin", "auxclk" + +This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz +clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock. + +eHRPWM Time Base Clock (TBCLK) +------------------------------ +Required properties: +- compatible: shall be "ti,da830-tbclksync". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "fck" + +PLL DIV4.5 divider +------------------ +Required properties: +- compatible: shall be "ti,da830-div4p5ena". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "pll0_pllout" + +EMIFA clock source (ASYNC1) +--------------------------- +Required properties: +- compatible: shall be "ti,da850-async1-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk3", "div4.5" + +ASYNC3 clock source +------------------- +Required properties: +- compatible: shall be "ti,da850-async3-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2" + +Examples: + + cfgchip: syscon@1417c { + compatible = "ti,da830-cfgchip", "syscon", "simple-mfd"; + reg = <0x1417c 0x14>; + + usb_phy_clk: usb-phy-clocks { + compatible = "ti,da830-usb-phy-clocks"; + #clock-cells = <1>; + clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>; + clock-names = "fck", "usb_refclkin", "auxclk"; + }; + ehrpwm_tbclk: ehrpwm_tbclk { + compatible = "ti,da830-tbclksync"; + #clock-cells = <0>; + clocks = <&psc1 17>; + clock-names = "fck"; + }; + div4p5_clk: div4.5 { + compatible = "ti,da830-div4p5ena"; + #clock-cells = <0>; + clocks = <&pll0_pllout>; + clock-names = "pll0_pllout"; + }; + async1_clk: async1 { + compatible = "ti,da850-async1-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 3>, <&div4p5_clk>; + clock-names = "pll0_sysclk3", "div4.5"; + }; + async3_clk: async3 { + compatible = "ti,da850-async3-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>; + clock-names = "pll0_sysclk2", "pll1_sysclk2"; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt + diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt new file mode 100644 index 000000000000..36998e184821 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -0,0 +1,96 @@ +Binding for TI DaVinci PLL Controllers + +The PLL provides clocks to most of the components on the SoC. In addition +to the PLL itself, this controller also contains bypasses, gates, dividers, +an multiplexers for various clock signals. + +Required properties: +- compatible: shall be one of: + - "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX + - "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area. +- clocks: phandles corresponding to the clock names +- clock-names: names of the clock sources - depends on compatible string + - for "ti,da850-pll0", shall be "clksrc", "extclksrc" + - for "ti,da850-pll1", shall be "clksrc" + +Optional properties: +- ti,clkmode-square-wave: Indicates that the the board is supplying a square + wave input on the OSCIN pin instead of using a crystal oscillator. + This property is only valid when compatible = "ti,da850-pll0". + + +Optional child nodes: + +pllout + Describes the main PLL clock output (before POSTDIV). The node name must + be "pllout". + + Required properties: + - #clock-cells: shall be 0 + +sysclk + Describes the PLLDIVn divider clocks that provide the SYSCLKn clock + domains. The node name must be "sysclk". Consumers of this node should + use "n" in "SYSCLKn" as the index parameter for the clock cell. + + Required properties: + - #clock-cells: shall be 1 + +auxclk + Describes the AUXCLK output of the PLL. The node name must be "auxclk". + This child node is only valid when compatible = "ti,da850-pll0". + + Required properties: + - #clock-cells: shall be 0 + +obsclk + Describes the OBSCLK output of the PLL. The node name must be "obsclk". + + Required properties: + - #clock-cells: shall be 0 + + +Examples: + + pll0: clock-controller@11000 { + compatible = "ti,da850-pll0"; + reg = <0x11000 0x1000>; + clocks = <&ref_clk>, <&pll1_sysclk 3>; + clock-names = "clksrc", "extclksrc"; + ti,clkmode-square-wave; + + pll0_pllout: pllout { + #clock-cells = <0>; + }; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_auxclk: auxclk { + #clock-cells = <0>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + + pll1: clock-controller@21a000 { + compatible = "ti,da850-pll1"; + reg = <0x21a000 0x1000>; + clocks = <&ref_clk>; + clock-names = "clksrc"; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt new file mode 100644 index 000000000000..dae4ad8e198c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt @@ -0,0 +1,71 @@ +Binding for TI DaVinci Power Sleep Controller (PSC) + +The PSC provides power management, clock gating and reset functionality. It is +primarily used for clocking. + +Required properties: +- compatible: shall be one of: + - "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX + - "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area +- #clock-cells: from common clock binding; shall be set to 1 +- #power-domain-cells: from generic power domain binding; shall be set to 1. +- clocks: phandles to clocks corresponding to the clock-names property +- clock-names: list of parent clock names - depends on compatible value + - for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1" + - for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3" + +Optional properties: +- #reset-cells: from reset binding; shall be set to 1 - only applicable when + at least one local domain provides a local reset. + +Consumers: + + Clock, power domain and reset consumers shall use the local power domain + module ID (LPSC) as the index corresponding to the clock cell. Refer to + the device-specific datasheet to find these numbers. NB: Most local + domains only provide a clock/power domain and not a reset. + +Examples: + + psc0: clock-controller@10000 { + compatible = "ti,da850-psc0"; + reg = <0x10000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>, + <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>; + clock_names = "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1"; + }; + psc1: clock-controller@227000 { + compatible = "ti,da850-psc1"; + reg = <0x227000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>; + clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3"; + }; + + /* consumer */ + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + clocks = <&psc0 15>; + power-domains = <&psc0 15>; + resets = <&psc0 15>; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt +- Documentation/devicetree/bindings/power/power_domain.txt +- Documentation/devicetree/bindings/reset/reset.txt diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt index 35a6f5c7e5c2..9b13b32974f9 100644 --- a/Documentation/devicetree/bindings/clock/ti/divider.txt +++ b/Documentation/devicetree/bindings/clock/ti/divider.txt @@ -75,6 +75,9 @@ Optional properties: - ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0, see [2] - ti,set-rate-parent : clk_set_rate is propagated to parent +- ti,latch-bit : latch the divider value to HW, only needed if the register + access requires this. As an example dra76x DPLL_GMAC H14 divider implements + such behavior. Examples: dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 { diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt index 2d0d170f8001..eec8994b9be8 100644 --- a/Documentation/devicetree/bindings/clock/ti/mux.txt +++ b/Documentation/devicetree/bindings/clock/ti/mux.txt @@ -48,6 +48,9 @@ Optional properties: zero - ti,set-rate-parent : clk_set_rate is propagated to parent clock, not supported by the composite-mux-clock subtype +- ti,latch-bit : latch the mux value to HW, only needed if the register + access requires this. As an example, dra7x DPLL_GMAC H14 muxing + implements such behavior. Examples: diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index 76aec8a3724d..3c1f3a229eab 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -415,12 +415,27 @@ Secure Non-Volatile Storage (SNVS) Low Power (LP) RTC Node value type: <u32> Definition: LP register offset. default it is 0x34. + - clocks + Usage: optional, required if SNVS LP RTC requires explicit + enablement of clocks + Value type: <prop_encoded-array> + Definition: a clock specifier describing the clock required for + enabling and disabling SNVS LP RTC. + + - clock-names + Usage: optional, required if SNVS LP RTC requires explicit + enablement of clocks + Value type: <string> + Definition: clock name string should be "snvs-rtc". + EXAMPLE sec_mon_rtc_lp@1 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; interrupts = <93 2>; regmap = <&snvs>; offset = <0x34>; + clocks = <&clks IMX7D_SNVS_CLK>; + clock-names = "snvs-rtc"; }; ===================================================================== @@ -543,6 +558,8 @@ FULL EXAMPLE regmap = <&sec_mon>; offset = <0x34>; interrupts = <93 2>; + clocks = <&clks IMX7D_SNVS_CLK>; + clock-names = "snvs-rtc"; }; snvs-pwrkey@020cc000 { diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt index baf9b34d20bf..b6a8cc0978cd 100644 --- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt +++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt @@ -74,8 +74,8 @@ Example: bcm2835_i2s: i2s@7e203000 { compatible = "brcm,bcm2835-i2s"; - reg = < 0x7e203000 0x20>, - < 0x7e101098 0x02>; + reg = < 0x7e203000 0x24>; + clocks = <&clocks BCM2835_CLOCK_PCM>; dmas = <&dma 2>, <&dma 3>; diff --git a/Documentation/devicetree/bindings/dma/mtk-hsdma.txt b/Documentation/devicetree/bindings/dma/mtk-hsdma.txt new file mode 100644 index 000000000000..4bb317359dc6 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mtk-hsdma.txt @@ -0,0 +1,33 @@ +MediaTek High-Speed DMA Controller +================================== + +This device follows the generic DMA bindings defined in dma/dma.txt. + +Required properties: + +- compatible: Must be one of + "mediatek,mt7622-hsdma": for MT7622 SoC + "mediatek,mt7623-hsdma": for MT7623 SoC +- reg: Should contain the register's base address and length. +- interrupts: Should contain a reference to the interrupt used by this + device. +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. +- clock-names: Should contain "hsdma" entries. +- power-domains: Phandle to the power domain that the device is part of +- #dma-cells: The length of the DMA specifier, must be <1>. This one cell + in dmas property of a client device represents the channel + number. +Example: + + hsdma: dma-controller@1b007000 { + compatible = "mediatek,mt7623-hsdma"; + reg = <0 0x1b007000 0 0x1000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_LOW>; + clocks = <ðsys CLK_ETHSYS_HSDMA>; + clock-names = "hsdma"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + #dma-cells = <1>; + }; + +DMA clients must use the format described in dma/dma.txt file. diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index 9cbf5d9df8fd..cf5b9e44432c 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -15,6 +15,10 @@ Required properties: the secure world. - qcom,controlled-remotely : optional, indicates that the bam is controlled by remote proccessor i.e. execution environment. +- num-channels : optional, indicates supported number of DMA channels in a + remotely controlled bam. +- qcom,num-ees : optional, indicates supported number of Execution Environments + in a remotely controlled bam. Example: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 891db41e9420..aadfb236d53a 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -18,6 +18,7 @@ Required Properties: Examples with soctypes are: - "renesas,dmac-r8a7743" (RZ/G1M) - "renesas,dmac-r8a7745" (RZ/G1E) + - "renesas,dmac-r8a77470" (RZ/G1C) - "renesas,dmac-r8a7790" (R-Car H2) - "renesas,dmac-r8a7791" (R-Car M2-W) - "renesas,dmac-r8a7792" (R-Car V2H) @@ -26,6 +27,7 @@ Required Properties: - "renesas,dmac-r8a7795" (R-Car H3) - "renesas,dmac-r8a7796" (R-Car M3-W) - "renesas,dmac-r8a77970" (R-Car V3M) + - "renesas,dmac-r8a77980" (R-Car V3H) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index f3d1f151ba80..9dc935e24e55 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -11,6 +11,7 @@ Required Properties: - "renesas,r8a7794-usb-dmac" (R-Car E2) - "renesas,r8a7795-usb-dmac" (R-Car H3) - "renesas,r8a7796-usb-dmac" (R-Car M3-W) + - "renesas,r8a77965-usb-dmac" (R-Car M3-N) - reg: base address and length of the registers block for the DMAC - interrupts: interrupt specifiers for the DMAC, one for each entry in interrupt-names. diff --git a/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt b/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt new file mode 100644 index 000000000000..f237b7928283 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt @@ -0,0 +1,41 @@ +Synopsys DesignWare AXI DMA Controller + +Required properties: +- compatible: "snps,axi-dma-1.01a" +- reg: Address range of the DMAC registers. This should include + all of the per-channel registers. +- interrupt: Should contain the DMAC interrupt number. +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device. +- dma-channels: Number of channels supported by hardware. +- snps,dma-masters: Number of AXI masters supported by the hardware. +- snps,data-width: Maximum AXI data width supported by hardware. + (0 - 8bits, 1 - 16bits, 2 - 32bits, ..., 6 - 512bits) +- snps,priority: Priority of channel. Array size is equal to the number of + dma-channels. Priority value must be programmed within [0:dma-channels-1] + range. (0 - minimum priority) +- snps,block-size: Maximum block size supported by the controller channel. + Array size is equal to the number of dma-channels. + +Optional properties: +- snps,axi-max-burst-len: Restrict master AXI burst length by value specified + in this property. If this property is missing the maximum AXI burst length + supported by DMAC is used. [1:256] + +Example: + +dmac: dma-controller@80000 { + compatible = "snps,axi-dma-1.01a"; + reg = <0x80000 0x400>; + clocks = <&core_clk>, <&cfgr_clk>; + clock-names = "core-clk", "cfgr-clk"; + interrupt-parent = <&intc>; + interrupts = <27>; + + dma-channels = <4>; + snps,dma-masters = <2>; + snps,data-width = <3>; + snps,block-size = <4096 4096 4096 4096>; + snps,priority = <0 1 2 3>; + snps,axi-max-burst-len = <16>; +}; diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt index 0b55718bf889..c5f519097204 100644 --- a/Documentation/devicetree/bindings/dma/stm32-dma.txt +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -62,14 +62,14 @@ channel: a phandle to the DMA controller plus the following four integer cells: 0x1: medium 0x2: high 0x3: very high -4. A 32bit mask specifying the DMA FIFO threshold configuration which are device - dependent: - -bit 0-1: Fifo threshold +4. A 32bit bitfield value specifying DMA features which are device dependent: + -bit 0-1: DMA FIFO threshold selection 0x0: 1/4 full FIFO 0x1: 1/2 full FIFO 0x2: 3/4 full FIFO 0x3: full FIFO + Example: usart1: serial@40011000 { diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt index abfae1beca2b..61d833abafbf 100644 --- a/Documentation/devicetree/bindings/eeprom/at24.txt +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -41,12 +41,16 @@ Required properties: "nxp", "ramtron", "renesas", + "rohm", "st", Some vendors use different model names for chips which are just variants of the above. Known such exceptions are listed below: + "nxp,se97b" - the fallback is "atmel,24c02", "renesas,r1ex24002" - the fallback is "atmel,24c02" + "renesas,r1ex24128" - the fallback is "atmel,24c128" + "rohm,br24t01" - the fallback is "atmel,24c01" - reg: The I2C address of the EEPROM. diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index ad876548ab5d..c1f65d1dac1d 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -10,6 +10,7 @@ Required properties: * And, optionally, one of the vendor specific compatible: + allwinner,sun4i-a10-mali + allwinner,sun7i-a20-mali + + allwinner,sun8i-h3-mali + allwinner,sun50i-h5-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index a777477e4547..4a7811ecd954 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -13,7 +13,9 @@ Required properties: "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC. "renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC. + "renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC. "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible device. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 224390999e81..fc7e17802746 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -13,6 +13,7 @@ Required properties: - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-r8a7796" (R-Car M3-W) + - "renesas,iic-r8a77965" (R-Car M3-N) - "renesas,iic-sh73a0" (SH-Mobile AG5) - "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1 compatible device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt new file mode 100644 index 000000000000..72f4a2f0fedc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt @@ -0,0 +1,29 @@ +Socionext SynQuacer I2C + +Required properties: +- compatible : Must be "socionext,synquacer-i2c" +- reg : Offset and length of the register set for the device +- interrupts : A single interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "pclk". +- clocks : Must contain an entry for each name in clock-names. + (See the common clock bindings.) + +Optional properties: +- clock-frequency : Desired I2C bus clock frequency in Hz. As only Normal and + Fast modes are supported, possible values are 100000 and + 400000. + +Example : + + i2c@51210000 { + compatible = "socionext,synquacer-i2c"; + reg = <0x51210000 0x1000>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "pclk"; + clocks = <&clk_i2c>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index a94940481e55..996ce84352cb 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -26,6 +26,14 @@ Optional subnode-properties: If not specified defaults to 5. - wakeup-source: Boolean, button can wake-up the system. (Legacy property supported: "gpio-key,wakeup") + - wakeup-event-action: Specifies whether the key should wake the + system when asserted, when deasserted, or both. This property is + only valid for keys that wake up the system (e.g., when the + "wakeup-source" property is also provided). + Supported values are defined in linux-event-codes.h: + EV_ACT_ASSERTED - asserted + EV_ACT_DEASSERTED - deasserted + EV_ACT_ANY - both asserted and deasserted - linux,can-disable: Boolean, indicates that button is connected to dedicated (not shared) interrupt which can be disabled to suppress events from the button. diff --git a/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt b/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt new file mode 100644 index 000000000000..43ef770dfeb9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt @@ -0,0 +1,22 @@ +Zodiac Inflight Innovations RAVE Supervisory Processor Power Button Bindings + +RAVE SP input device is a "MFD cell" device corresponding to power +button functionality of RAVE Supervisory Processor. It is expected +that its Device Tree node is specified as a child of the node +corresponding to the parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-pwrbutton" + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + pwrbutton { + compatible = "zii,rave-sp-pwrbutton"; + }; + } diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 1fd5d69647ca..ffadb7c6f1f3 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -11,6 +11,8 @@ Required Properties: the device is compatible with the R-Car Gen2 VMSA-compatible IPMMU. - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. + - "renesas,ipmmu-r8a7743" for the R8A7743 (RZ/G1M) IPMMU. + - "renesas,ipmmu-r8a7745" for the R8A7745 (RZ/G1E) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. @@ -19,7 +21,8 @@ Required Properties: - "renesas,ipmmu-r8a7796" for the R8A7796 (R-Car M3-W) IPMMU. - "renesas,ipmmu-r8a77970" for the R8A77970 (R-Car V3M) IPMMU. - "renesas,ipmmu-r8a77995" for the R8A77995 (R-Car D3) IPMMU. - - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. + - "renesas,ipmmu-vmsa" for generic R-Car Gen2 or RZ/G1 VMSA-compatible + IPMMU. - reg: Base address and size of the IPMMU registers. - interrupts: Specifiers for the MMU fault interrupts. For instances that diff --git a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt index 2098f7732264..6ecefea1c6f9 100644 --- a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt @@ -14,6 +14,11 @@ Required properties: "single-master" device, and needs no additional information to associate with its master device. See: Documentation/devicetree/bindings/iommu/iommu.txt +- clocks : A list of clocks required for the IOMMU to be accessible by + the host CPU. +- clock-names : Should contain the following: + "iface" - Main peripheral bus clock (PCLK/HCL) (required) + "aclk" - AXI bus clock (required) Optional properties: - rockchip,disable-mmu-reset : Don't use the mmu reset operation. @@ -27,5 +32,7 @@ Example: reg = <0xff940300 0x100>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopl_mmu"; + clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt b/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt new file mode 100644 index 000000000000..3e5b4537407d --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt @@ -0,0 +1,51 @@ +Hisilicon Hi3660 Mailbox Controller + +Hisilicon Hi3660 mailbox controller supports up to 32 channels. Messages +are passed between processors, including application & communication +processors, MCU, HIFI, etc. Each channel is unidirectional and accessed +by using MMIO registers; it supports maximum to 8 words message. + +Controller +---------- + +Required properties: +- compatible: : Shall be "hisilicon,hi3660-mbox" +- reg: : Offset and length of the device's register set +- #mbox-cells: : Must be 3 + <&phandle channel dst_irq ack_irq> + phandle : Label name of controller + channel : Channel number + dst_irq : Remote interrupt vector + ack_irq : Local interrupt vector + +- interrupts: : Contains the two IRQ lines for mailbox. + +Example: + +mailbox: mailbox@e896b000 { + compatible = "hisilicon,hi3660-mbox"; + reg = <0x0 0xe896b000 0x0 0x1000>; + interrupts = <0x0 0xc0 0x4>, + <0x0 0xc1 0x4>; + #mbox-cells = <3>; +}; + +Client +------ + +Required properties: +- compatible : See the client docs +- mboxes : Standard property to specify a Mailbox (See ./mailbox.txt) + Cells must match 'mbox-cells' (See Controller docs above) + +Optional properties +- mbox-names : Name given to channels seen in the 'mboxes' property. + +Example: + +stub_clock: stub_clock@e896b500 { + compatible = "hisilicon,hi3660-stub-clk"; + reg = <0x0 0xe896b500 0x0 0x0100>; + #clock-cells = <1>; + mboxes = <&mailbox 13 3 0>; +}; diff --git a/Documentation/devicetree/bindings/mailbox/mailbox.txt b/Documentation/devicetree/bindings/mailbox/mailbox.txt index be05b9746c69..af8ecee2ac68 100644 --- a/Documentation/devicetree/bindings/mailbox/mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/mailbox.txt @@ -23,6 +23,11 @@ Required property: Optional property: - mbox-names: List of identifier strings for each mailbox channel. +- shmem : List of phandle pointing to the shared memory(SHM) area between the + users of these mailboxes for IPC, one for each mailbox. This shared + memory can be part of any memory reserved for the purpose of this + communication between the mailbox client and the remote. + Example: pwr_cntrl: power { @@ -30,3 +35,26 @@ Example: mbox-names = "pwr-ctrl", "rpc"; mboxes = <&mailbox 0 &mailbox 1>; }; + +Example with shared memory(shmem): + + sram: sram@50000000 { + compatible = "mmio-sram"; + reg = <0x50000000 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x50000000 0x10000>; + + cl_shmem: shmem@0 { + compatible = "client-shmem"; + reg = <0x0 0x200>; + }; + }; + + client@2e000000 { + ... + mboxes = <&mailbox 0>; + shmem = <&cl_shmem>; + .. + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt index 621b41c79faa..44d71469c914 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -3,7 +3,9 @@ EMIF - External Memory Interface - is an SDRAM controller used in TI SoCs. EMIF supports, based on the IP revision, one or more of DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance -of the EMIF IP and memory parts attached to it. +of the EMIF IP and memory parts attached to it. Certain revisions +of the EMIF controller also contain optional ECC support, which +corrects one bit errors and detects two bit errors. Required properties: - compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> @@ -11,6 +13,8 @@ Required properties: compatible should be one of the following: "ti,emif-am3352" "ti,emif-am4372" + "ti,emif-dra7xx" + "ti,emif-keystone" - phy-type : <u32> indicating the DDR phy type. Following are the allowed values @@ -22,6 +26,7 @@ Required properties: - ti,hwmods : For TI hwmods processing and omap device creation the value shall be "emif<n>" where <n> is the number of the EMIF instance with base 1. +- interrupts : interrupt used by the controller Required only for "ti,emif-am3352" and "ti,emif-am4372": - sram : Phandles for generic sram driver nodes, @@ -71,3 +76,9 @@ emif: emif@4c000000 { sram = <&pm_sram_code &pm_sram_data>; }; + +emif1: emif@4c000000 { + compatible = "ti,emif-dra7xx"; + reg = <0x4c000000 0x200>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt index 69aadee00d5f..34dd89087cff 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -176,3 +176,24 @@ lhc: lhc@20 { compatible = "aspeed,ast2500-lhc"; reg = <0x20 0x24 0x48 0x8>; }; + +LPC reset control +----------------- + +The UARTs present in the ASPEED SoC can have their resets tied to the reset +state of the LPC bus. Some systems may chose to modify this configuration. + +Required properties: + + - compatible: "aspeed,ast2500-lpc-reset" or + "aspeed,ast2400-lpc-reset" + - reg: offset and length of the IP in the LHC memory region + - #reset-controller indicates the number of reset cells expected + +Example: + +lpc_reset: reset-controller@18 { + compatible = "aspeed,ast2500-lpc-reset"; + reg = <0x18 0x4>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt new file mode 100644 index 000000000000..ae15ec333542 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -0,0 +1,43 @@ +* Microsemi MIPS CPUs + +Boards with a SoC of the Microsemi MIPS family shall have the following +properties: + +Required properties: +- compatible: "mscc,ocelot" + + +* Other peripherals: + +o CPU chip regs: + +The SoC has a few registers (DEVCPU_GCB:CHIP_REGS) handling miscellaneous +functionalities: chip ID, general purpose register for software use, reset +controller, hardware status and configuration, efuses. + +Required properties: +- compatible: Should be "mscc,ocelot-chip-regs", "simple-mfd", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@71070000 { + compatible = "mscc,ocelot-chip-regs", "simple-mfd", "syscon"; + reg = <0x71070000 0x1c>; + }; + + +o CPU system control: + +The SoC has a few registers (ICPU_CFG:CPU_SYSTEM_CTRL) handling configuration of +the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU +endianness, CPU bus control, CPU status. + +Required properties: +- compatible: Should be "mscc,ocelot-cpu-syscon", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@70000000 { + compatible = "mscc,ocelot-cpu-syscon", "syscon"; + reg = <0x70000000 0x2c>; + }; diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c6558785e61b..8ce49b255974 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -21,7 +21,7 @@ Required Properties: - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 Optional Properties: -* clocks: from common clock binding: if ciu_drive and ciu_sample are +* clocks: from common clock binding: if ciu-drive and ciu-sample are specified in clock-names, should contain handles to these clocks. * clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt @@ -29,7 +29,7 @@ Optional Properties: to control the clock phases, "ciu-sample" is required for tuning high- speed modes. -* rockchip,default-sample-phase: The default phase to set ciu_sample at +* rockchip,default-sample-phase: The default phase to set ciu-sample at probing, low speeds or in case where all phases work at tuning time. If not specified 0 deg will be used. diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 63d4d626fbd5..483e9cfac1b1 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -39,3 +39,27 @@ qspi0: quadspi@40044000 { .... }; }; + +Example showing the usage of two SPI NOR devices: + +&qspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi2>; + status = "okay"; + + flash0: n25q256a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + reg = <0>; + }; + + flash1: n25q256a@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt index c08fb477b3c6..e0c790706b9b 100644 --- a/Documentation/devicetree/bindings/mtd/marvell-nand.txt +++ b/Documentation/devicetree/bindings/mtd/marvell-nand.txt @@ -14,7 +14,10 @@ Required properties: - #address-cells: shall be set to 1. Encode the NAND CS. - #size-cells: shall be set to 0. - interrupts: shall define the NAND controller interrupt. -- clocks: shall reference the NAND controller clock. +- clocks: shall reference the NAND controller clocks, the second one is + is only needed for the Armada 7K/8K SoCs +- clock-names: mandatory if there is a second clock, in this case there + should be one clock named "core" and another one named "reg" - marvell,system-controller: Set to retrieve the syscon node that handles NAND controller related registers (only required with the "marvell,armada-8k-nand[-controller]" compatibles). diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 4a0a48bf4ecb..232fa12e90ef 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -41,6 +41,13 @@ additional (optional) property is defined: - erase-size : The chip's physical erase block size in bytes. + The device tree may optionally contain endianness property. + little-endian or big-endian : It Represents the endianness that should be used + by the controller to properly read/write data + from/to the flash. If this property is missing, + the endianness is chosen by the system + (potentially based on extra configuration options). + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt deleted file mode 100644 index d4ee4da58463..000000000000 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ /dev/null @@ -1,50 +0,0 @@ -PXA3xx NAND DT bindings - -Required properties: - - - compatible: Should be set to one of the following: - marvell,pxa3xx-nand - marvell,armada370-nand - marvell,armada-8k-nand - - reg: The register base for the controller - - interrupts: The interrupt to map - - #address-cells: Set to <1> if the node includes partitions - - marvell,system-controller: Set to retrieve the syscon node that handles - NAND controller related registers (only required - with marvell,armada-8k-nand compatible). - -Optional properties: - - - dmas: dma data channel, see dma.txt binding doc - - marvell,nand-enable-arbiter: Set to enable the bus arbiter - - marvell,nand-keep-config: Set to keep the NAND controller config as set - by the bootloader - - num-cs: Number of chipselect lines to use - - nand-on-flash-bbt: boolean to enable on flash bbt option if - not present false - - nand-ecc-strength: number of bits to correct per ECC step - - nand-ecc-step-size: number of data bytes covered by a single ECC step - -The following ECC strength and step size are currently supported: - - - nand-ecc-strength = <1>, nand-ecc-step-size = <512> - - nand-ecc-strength = <4>, nand-ecc-step-size = <512> - - nand-ecc-strength = <8>, nand-ecc-step-size = <512> - -Example: - - nand0: nand@43100000 { - compatible = "marvell,pxa3xx-nand"; - reg = <0x43100000 90>; - interrupts = <45>; - dmas = <&pdma 97 0>; - dma-names = "data"; - #address-cells = <1>; - - marvell,nand-enable-arbiter; - marvell,nand-keep-config; - num-cs = <1>; - - /* partitions (optional) */ - }; - diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 5e13a5cdff03..0734f03bf3d3 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -24,8 +24,8 @@ Optional properties: - allwinner,rb : shall contain the native Ready/Busy ids. or - rb-gpios : shall contain the gpios used as R/B pins. -- nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft", - "soft_bch" or "none") +- nand-ecc-mode : one of the supported ECC modes ("hw", "soft", "soft_bch" or + "none") see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 594982c6b9f9..79bf352e659c 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -6,7 +6,11 @@ the definition of the PHY node in booting-without-of.txt for an example of how to define a PHY. Required properties: - - reg : Offset and length of the register set for the device + - reg : Offset and length of the register set for the device, and optionally + the offset and length of the TBIPA register (TBI PHY address + register). If TBIPA register is not specified, the driver will + attempt to infer it from the register set specified (your mileage may + vary). - compatible : Should define the compatible device type for the mdio. Currently supported strings/devices are: - "fsl,gianfar-tbi" diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt index c84bc027930b..760b4d740616 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -34,6 +34,7 @@ Required properties Optional properties: - reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- vpcie-supply: The regulator in charge of PCIe port power. - phys: List of phandle and phy mode specifier, should be 0. - phy-names: Must be "phy". diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 3a6ce55dd310..20227a875ac8 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -78,7 +78,7 @@ Examples for MT7623: #reset-cells = <1>; }; - pcie: pcie-controller@1a140000 { + pcie: pcie@1a140000 { compatible = "mediatek,mt7623-pcie"; device_type = "pci"; reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ @@ -111,7 +111,6 @@ Examples for MT7623: 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -123,7 +122,6 @@ Examples for MT7623: }; pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -135,7 +133,6 @@ Examples for MT7623: }; pcie@2,0 { - device_type = "pci"; reg = <0x1000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -148,6 +145,7 @@ Examples for MT7623: }; Examples for MT2712: + pcie: pcie@11700000 { compatible = "mediatek,mt2712-pcie"; device_type = "pci"; @@ -169,7 +167,6 @@ Examples for MT2712: ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; pcie0: pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -189,7 +186,6 @@ Examples for MT2712: }; pcie1: pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -210,6 +206,7 @@ Examples for MT2712: }; Examples for MT7622: + pcie: pcie@1a140000 { compatible = "mediatek,mt7622-pcie"; device_type = "pci"; @@ -243,7 +240,6 @@ Examples for MT7622: ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; pcie0: pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -263,7 +259,6 @@ Examples for MT7622: }; pcie1: pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 3c9d321b3d3b..1fd703bd73e0 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -189,6 +189,10 @@ Value type: <phandle> Definition: A phandle to the analog power supply for IC which generates reference clock +- vddpe-3v3-supply: + Usage: optional + Value type: <phandle> + Definition: A phandle to the PCIe endpoint power supply - phys: Usage: required for apq8084 diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 76ba3a61d1a3..1fb614e615da 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -1,13 +1,15 @@ * Renesas R-Car PCIe interface Required properties: -compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; +compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; + "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-r8a7796" for the R8A7796 SoC; - "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or + RZ/G1 compatible device. "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/perf/arm-ccn.txt index 43b5a71a5a9d..43b5a71a5a9d 100644 --- a/Documentation/devicetree/bindings/arm/ccn.txt +++ b/Documentation/devicetree/bindings/perf/arm-ccn.txt diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt index a9aa79fb90ed..1aa6f2674af5 100644 --- a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt @@ -21,7 +21,9 @@ Required properties : - timer: The timeout clock (clk_m). Present if phy_type == utmi. - utmi-pads: The clock needed to access the UTMI pad control registers. Present if phy_type == utmi. - - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). + - ulpi-link: The clock Tegra provides to the ULPI PHY (usually pad DAP_MCLK2 + with pad group aka "nvidia,pins" cdev2 and pin mux option config aka + "nvidia,function" pllp_out4). Present if phy_type == ulpi, and ULPI link mode is in use. - resets : Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 2c46f30b62c5..9a06e1fdbc42 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -11,6 +11,7 @@ Required properies: "st,stm32f429-pinctrl" "st,stm32f469-pinctrl" "st,stm32f746-pinctrl" + "st,stm32f769-pinctrl" "st,stm32h743-pinctrl" "st,stm32mp157-pinctrl" "st,stm32mp157-z-pinctrl" diff --git a/Documentation/devicetree/bindings/pmem/pmem-region.txt b/Documentation/devicetree/bindings/pmem/pmem-region.txt new file mode 100644 index 000000000000..5cfa4f016a00 --- /dev/null +++ b/Documentation/devicetree/bindings/pmem/pmem-region.txt @@ -0,0 +1,65 @@ +Device-tree bindings for persistent memory regions +----------------------------------------------------- + +Persistent memory refers to a class of memory devices that are: + + a) Usable as main system memory (i.e. cacheable), and + b) Retain their contents across power failure. + +Given b) it is best to think of persistent memory as a kind of memory mapped +storage device. To ensure data integrity the operating system needs to manage +persistent regions separately to the normal memory pool. To aid with that this +binding provides a standardised interface for discovering where persistent +memory regions exist inside the physical address space. + +Bindings for the region nodes: +----------------------------- + +Required properties: + - compatible = "pmem-region" + + - reg = <base, size>; + The reg property should specificy an address range that is + translatable to a system physical address range. This address + range should be mappable as normal system memory would be + (i.e cacheable). + + If the reg property contains multiple address ranges + each address range will be treated as though it was specified + in a separate device node. Having multiple address ranges in a + node implies no special relationship between the two ranges. + +Optional properties: + - Any relevant NUMA assocativity properties for the target platform. + + - volatile; This property indicates that this region is actually + backed by non-persistent memory. This lets the OS know that it + may skip the cache flushes required to ensure data is made + persistent after a write. + + If this property is absent then the OS must assume that the region + is backed by non-volatile memory. + +Examples: +-------------------- + + /* + * This node specifies one 4KB region spanning from + * 0x5000 to 0x5fff that is backed by non-volatile memory. + */ + pmem@5000 { + compatible = "pmem-region"; + reg = <0x00005000 0x00001000>; + }; + + /* + * This node specifies two 4KB regions that are backed by + * volatile (normal) memory. + */ + pmem@6000 { + compatible = "pmem-region"; + reg = < 0x00006000 0x00001000 + 0x00008000 0x00001000 >; + volatile; + }; + diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 8690f10426a3..ab399e559257 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,7 +17,9 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77965-sysc" (R-Car M3-N) - "renesas,r8a77970-sysc" (R-Car V3M) + - "renesas,r8a77980-sysc" (R-Car V3H) - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt new file mode 100644 index 000000000000..7d9d3f90641b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt @@ -0,0 +1,25 @@ +Ingenic JZ47xx PWM Controller +============================= + +Required properties: +- compatible: One of: + * "ingenic,jz4740-pwm" + * "ingenic,jz4770-pwm" + * "ingenic,jz4780-pwm" +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description + of the cells format. +- clocks : phandle to the external clock. +- clock-names : Should be "ext". + + +Example: + + pwm: pwm@10002000 { + compatible = "ingenic,jz4740-pwm"; + reg = <0x10002000 0x1000>; + + #pwm-cells = <3>; + + clocks = <&ext>; + clock-names = "ext"; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt index f8338d11fd2b..bd23302e84be 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -7,6 +7,8 @@ See ../mfd/stm32-lptimer.txt for details about the parent node. Required parameters: - compatible: Must be "st,stm32-pwm-lp". +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. Optional properties: - pinctrl-names: Set to "default". @@ -18,6 +20,7 @@ Example: ... pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; pinctrl-names = "default"; pinctrl-0 = <&lppwm1_pins>; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt index 51ff54c8b8ef..2a1affbff45e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -7,6 +7,8 @@ Required properties: - "allwinner,sun5i-a13-pwm" - "allwinner,sun7i-a20-pwm" - "allwinner,sun8i-h3-pwm" + - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm" + - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt index 74c118015980..35a3b9761ee5 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -2,6 +2,8 @@ Required Properties: - compatible: should be "renesas,pwm-rcar" and one of the following. + - "renesas,pwm-r8a7743": for RZ/G1M + - "renesas,pwm-r8a7745": for RZ/G1E - "renesas,pwm-r8a7778": for R-Car M1A - "renesas,pwm-r8a7779": for R-Car H1 - "renesas,pwm-r8a7790": for R-Car H2 @@ -9,6 +11,7 @@ Required Properties: - "renesas,pwm-r8a7794": for R-Car E2 - "renesas,pwm-r8a7795": for R-Car H3 - "renesas,pwm-r8a7796": for R-Car M3-W + - "renesas,pwm-r8a77965": for R-Car M3-N - "renesas,pwm-r8a77995": for R-Car D3 - reg: base address and length of the registers block for the PWM. - #pwm-cells: should be 2. See pwm.txt in this directory for a description of @@ -17,13 +20,15 @@ Required Properties: - pinctrl-0: phandle, referring to a default pin configuration node. - pinctrl-names: Set to "default". -Example: R8A7790 (R-Car H2) PWM Timer node +Example: R8A7743 (RZ/G1M) PWM Timer node pwm0: pwm@e6e30000 { - compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar"; + compatible = "renesas,pwm-r8a7743", "renesas,pwm-rcar"; reg = <0 0xe6e30000 0 0x8>; + clocks = <&cpg CPG_MOD 523>; + power-domains = <&sysc R8A7743_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; - clocks = <&mstp5_clks R8A7790_CLK_PWM>; pinctrl-0 = <&pwm0_pins>; pinctrl-names = "default"; }; diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt index 1aadc804dae4..d53a16715da6 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -3,10 +3,12 @@ Required Properties: - compatible: should be one of the following. - - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. + - "renesas,tpu-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible PWM controller. - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. + - "renesas,tpu-r8a7743": for R8A7743 (RZ/G1M) compatible PWM controller. + - "renesas,tpu-r8a7745": for R8A7745 (RZ/G1E) compatible PWM controller. - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. - - "renesas,tpu": for generic R-Car TPU PWM controller. + - "renesas,tpu": for generic R-Car and RZ/G1 TPU PWM controller. - reg: Base address and length of each memory resource used by the PWM controller hardware module. @@ -18,10 +20,10 @@ Required Properties: Please refer to pwm.txt in this directory for details of the common PWM bindings used by client devices. -Example: R8A7740 (R-Car A1) TPU controller node +Example: R8A7740 (R-Mobile A1) TPU controller node tpu: pwm@e6600000 { compatible = "renesas,tpu-r8a7740", "renesas,tpu"; - reg = <0xe6600000 0x100>; + reg = <0xe6600000 0x148>; #pwm-cells = <3>; }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index a8014f3ab8ba..294a0dae106a 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,7 +26,9 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77965-rst" (R-Car M3-N) - "renesas,r8a77970-rst" (R-Car V3M) + - "renesas,r8a77980-rst" (R-Car V3H) - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt new file mode 100644 index 000000000000..b4edaf7c7ff3 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt @@ -0,0 +1,6 @@ +STMicroelectronics STM32MP1 Peripheral Reset Controller +======================================================= + +The RCC IP is both a reset and a clock controller. + +Please see Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt diff --git a/Documentation/devicetree/bindings/rtc/isil,isl12026.txt b/Documentation/devicetree/bindings/rtc/isil,isl12026.txt new file mode 100644 index 000000000000..2e0be45193bb --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/isil,isl12026.txt @@ -0,0 +1,28 @@ +ISL12026 I2C RTC/EEPROM + +ISL12026 is an I2C RTC/EEPROM combination device. The RTC and control +registers respond at bus address 0x6f, and the EEPROM array responds +at bus address 0x57. The canonical "reg" value will be for the RTC portion. + +Required properties supported by the device: + + - "compatible": must be "isil,isl12026" + - "reg": I2C bus address of the device (always 0x6f) + +Optional properties: + + - "isil,pwr-bsw": If present PWR.BSW bit must be set to the specified + value for proper operation. + + - "isil,pwr-sbib": If present PWR.SBIB bit must be set to the specified + value for proper operation. + + +Example: + + rtc@6f { + compatible = "isil,isl12026"; + reg = <0x6f>; + isil,pwr-bsw = <0>; + isil,pwr-sbib = <1>; + } diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index df3bef7998fa..8c6659ed2cfc 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -53,6 +53,13 @@ Main node required properties: Optional main node properties: - hip06-sas-v2-quirk-amt : when set, indicates that the v2 controller has the "am-max-transmissions" limitation. + - hisilicon,signal-attenuation : array of 3 32-bit values, containing de-emphasis, + preshoot, and boost attenuation readings for the board. They + are used to describe the signal attenuation of the board. These + values' range is 7600 to 12400, and used to represent -24dB to + 24dB. + The formula is "y = (x-10000)/10000". For example, 10478 + means 4.78dB. Example: sas0: sas@c1000000 { diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index 76bf45b893fa..d6fe16f094af 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -21,6 +21,8 @@ Required properties: - "mediatek,mt2712-scpsys" - "mediatek,mt6797-scpsys" - "mediatek,mt7622-scpsys" + - "mediatek,mt7623-scpsys", "mediatek,mt2701-scpsys": For MT7623 SoC + - "mediatek,mt7623a-scpsys": For MT7623A SoC - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit @@ -28,10 +30,11 @@ Required properties: - clock, clock-names: clocks according to the common clock binding. These are clocks which hardware needs to be enabled before enabling certain power domains. - Required clocks for MT2701: "mm", "mfg", "ethif" + Required clocks for MT2701 or MT7623: "mm", "mfg", "ethif" Required clocks for MT2712: "mm", "mfg", "venc", "jpgdec", "audio", "vdec" Required clocks for MT6797: "mm", "mfg", "vdec" Required clocks for MT7622: "hif_sel" + Required clocks for MT7622A: "ethif" Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: diff --git a/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt b/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt index 65783de0aedf..7bb0362828ec 100644 --- a/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt +++ b/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt @@ -2,9 +2,8 @@ Required properties: - compatible: "brcm,bcm2835-i2s" -- reg: A list of base address and size entries: - * The first entry should cover the PCM registers - * The second entry should cover the PCM clock registers +- reg: Should contain PCM registers location and length. +- clocks: the (PCM) clock to use - dmas: List of DMA controller phandle and DMA request line ordered pairs. - dma-names: Identifier string for each DMA request line in the dmas property. These strings correspond 1:1 with the ordered pairs in dmas. @@ -16,8 +15,8 @@ Example: bcm2835_i2s: i2s@7e203000 { compatible = "brcm,bcm2835-i2s"; - reg = <0x7e203000 0x20>, - <0x7e101098 0x02>; + reg = <0x7e203000 0x24>; + clocks = <&clocks BCM2835_CLOCK_PCM>; dmas = <&dma 2>, <&dma 3>; diff --git a/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt new file mode 100644 index 000000000000..ea22dfe485be --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt @@ -0,0 +1,21 @@ +Nuvoton NPCM7xx timer + +Nuvoton NPCM7xx have three timer modules, each timer module provides five 24-bit +timer counters. + +Required properties: +- compatible : "nuvoton,npcm750-timer" for Poleg NPCM750. +- reg : Offset and length of the register set for the device. +- interrupts : Contain the timer interrupt with flags for + falling edge. +- clocks : phandle of timer reference clock (usually a 25 MHz clock). + +Example: + +timer@f0008000 { + compatible = "nuvoton,npcm750-timer"; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xf0008000 0x50>; + clocks = <&clk NPCM7XX_CLK_TIMER>; +}; + diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt index b4aa7ddb5b13..f82087b220f4 100644 --- a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt +++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt @@ -15,7 +15,7 @@ Required properties: - interrupts : Should be the clock event device interrupt. - clocks : The clocks provided by the SoC to drive the timer, must contain an entry for each entry in clock-names. -- clock-names : Must include the following entries: "igp" and "per". +- clock-names : Must include the following entries: "ipg" and "per". Example: tpm5: tpm@40260000 { diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 2e3740f98c41..763a2808a95c 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -75,6 +75,18 @@ maxim,max6621 PECI-to-I2C translator for PECI-to-SMBus/I2C protocol conversion maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mcube,mc3230 mCube 3-axis 8-bit digital accelerometer memsic,mxc6225 MEMSIC 2-axis 8-bit digital accelerometer +microchip,mcp4017-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4017-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4017-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4017-104 Microchip 7-bit Single I2C Digital POT (100k) +microchip,mcp4018-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4018-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4018-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4018-104 Microchip 7-bit Single I2C Digital POT (100k) +microchip,mcp4019-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4019-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4019-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4019-104 Microchip 7-bit Single I2C Digital POT (100k) microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 12e8b3e576b0..b5f978a4cac6 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -225,6 +225,7 @@ motorola Motorola, Inc. moxa Moxa Inc. mpl MPL AG mqmaker mqmaker Inc. +mscc Microsemi Corporation msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) multi-inno Multi-Inno Technology Co.,Ltd diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 107280ef0025..adc6b76fcb3a 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -11,6 +11,7 @@ Optional properties: detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. - fsl,ext-reset-output: If present the watchdog device is configured to assert its external reset (WDOG_B) instead of issuing a software reset. +- timeout-sec : Contains the watchdog timeout in seconds Examples: @@ -19,4 +20,5 @@ wdt@73f98000 { reg = <0x73f98000 0x4000>; interrupts = <58>; big-endian; + timeout-sec = <20>; }; diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt index 8a6d84cb36c9..7588cc3971bf 100644 --- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -9,9 +9,13 @@ Required properties: "amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: wdt: watchdog@c1109900 { compatible = "amlogic,meson6-wdt"; reg = <0xc1109900 0x8>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index 5b38a30e608c..859dee167b91 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -11,9 +11,13 @@ Required properties: - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: wdt: watchdog@10000000 { compatible = "mediatek,mt6589-wdt"; reg = <0x10000000 0x18>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt new file mode 100644 index 000000000000..6d593003c933 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt @@ -0,0 +1,28 @@ +Nuvoton NPCM Watchdog + +Nuvoton NPCM timer module provides five 24-bit timer counters, and a watchdog. +The watchdog supports a pre-timeout interrupt that fires 10ms before the +expiry. + +Required properties: +- compatible : "nuvoton,npcm750-wdt" for NPCM750 (Poleg). +- reg : Offset and length of the register set for the device. +- interrupts : Contain the timer interrupt with flags for + falling edge. + +Required clocking property, have to be one of: +- clocks : phandle of timer reference clock. +- clock-frequency : The frequency in Hz of the clock that drives the NPCM7xx + timer (usually 25000000). + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + +Example: + +timer@f000801c { + compatible = "nuvoton,npcm750-wdt"; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xf000801c 0x4>; + clocks = <&clk NPCM7XX_CLK_TIMER>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt index 9cbc76c89b2b..0dce5e3100b4 100644 --- a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt @@ -5,10 +5,14 @@ Required properties: - reg: Address range of tick timer/WDT register set - interrupts: interrupt number to the cpu +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + Example: timer@b0020000 { compatible = "sirf,prima2-tick"; reg = <0xb0020000 0x1000>; interrupts = <0>; + timeout-sec = <30>; }; diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt index 62dd5baad70e..ed11ce0ac836 100644 --- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -2,13 +2,19 @@ Allwinner SoCs Watchdog timer Required properties: -- compatible : should be either "allwinner,sun4i-a10-wdt" or - "allwinner,sun6i-a31-wdt" +- compatible : should be one of + "allwinner,sun4i-a10-wdt" + "allwinner,sun6i-a31-wdt" + "allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt" - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + Example: wdt: watchdog@1c20c90 { compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; + timeout-sec = <10>; }; |