diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
169 files changed, 4170 insertions, 404 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt index 5a6b16070a33..b545856a444f 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -61,7 +61,9 @@ Required Properties: - #address-cells: must be 1 - #size-cells: must be 1 - interrupts : Should be single bit error interrupt, then double bit error - interrupt. Note the rising edge type. + interrupt. +- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller +- #interrupt-cells : must be set to 2. - ranges : standard definition, should translate from local addresses Subcomponents: @@ -70,11 +72,23 @@ L2 Cache ECC Required Properties: - compatible : Should be "altr,socfpga-a10-l2-ecc" - reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. On-Chip RAM ECC Required Properties: - compatible : Should be "altr,socfpga-a10-ocram-ecc" - reg : Address and size for ECC block registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +Ethernet FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-eth-mac-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent Ethernet node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. Example: @@ -85,15 +99,37 @@ Example: #size-cells = <1>; interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>, <0 0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; ranges; l2-ecc@ffd06010 { compatible = "altr,socfpga-a10-l2-ecc"; reg = <0xffd06010 0x4>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, + <32 IRQ_TYPE_LEVEL_HIGH>; }; ocram-ecc@ff8c3000 { compatible = "altr,socfpga-a10-ocram-ecc"; reg = <0xff8c3000 0x90>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>, + <33 IRQ_TYPE_LEVEL_HIGH> ; + }; + + emac0-rx-ecc@ff8c0800 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0800 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>, + <36 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-tx-ecc@ff8c0c00 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0c00 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>, + <37 IRQ_TYPE_LEVEL_HIGH>; }; }; diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 93147c0c8a0e..fcbae6a5e6c1 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -12,14 +12,33 @@ its hardware characteristcs. * compatible: These have to be supplemented with "arm,primecell" as drivers are using the AMBA bus interface. Possible values include: - - "arm,coresight-etb10", "arm,primecell"; - - "arm,coresight-tpiu", "arm,primecell"; - - "arm,coresight-tmc", "arm,primecell"; - - "arm,coresight-funnel", "arm,primecell"; - - "arm,coresight-etm3x", "arm,primecell"; - - "arm,coresight-etm4x", "arm,primecell"; - - "qcom,coresight-replicator1x", "arm,primecell"; - - "arm,coresight-stm", "arm,primecell"; [1] + - Embedded Trace Buffer (version 1.0): + "arm,coresight-etb10", "arm,primecell"; + + - Trace Port Interface Unit: + "arm,coresight-tpiu", "arm,primecell"; + + - Trace Memory Controller, used for Embedded Trace Buffer(ETB), + Embedded Trace FIFO(ETF) and Embedded Trace Router(ETR) + configuration. The configuration mode (ETB, ETF, ETR) is + discovered at boot time when the device is probed. + "arm,coresight-tmc", "arm,primecell"; + + - Trace Funnel: + "arm,coresight-funnel", "arm,primecell"; + + - Embedded Trace Macrocell (version 3.x) and + Program Flow Trace Macrocell: + "arm,coresight-etm3x", "arm,primecell"; + + - Embedded Trace Macrocell (version 4.x): + "arm,coresight-etm4x", "arm,primecell"; + + - Qualcomm Configurable Replicator (version 1.x): + "qcom,coresight-replicator1x", "arm,primecell"; + + - System Trace Macrocell: + "arm,coresight-stm", "arm,primecell"; [1] * reg: physical base address and length of the register set(s) of the component. diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt index c453ab5553cd..917199f17965 100644 --- a/Documentation/devicetree/bindings/arm/l2c2x0.txt +++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt @@ -86,10 +86,10 @@ Optional properties: firmware) - arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly disable), <1> (forcibly enable), property absent (OS specific behavior, - preferrably retain firmware settings) + preferably retain firmware settings) - arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable), <1> (forcibly enable), property absent (OS specific behavior, - preferrably retain firmware settings) + preferably retain firmware settings) Example: diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 74d5417d0410..61c8b4620415 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -39,7 +39,9 @@ Optional properties: When using a PPI, specifies a list of phandles to CPU nodes corresponding to the set of CPUs which have a PMU of this type signalling the PPI listed in the - interrupts property. + interrupts property, unless this is already specified + by the PPI interrupt specifier itself (in which case + the interrupt-affinity property shouldn't be present). This property should be present when there is more than a single SPI. diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt index 0f7b9c2109f8..c9b9321434ea 100644 --- a/Documentation/devicetree/bindings/arm/xen.txt +++ b/Documentation/devicetree/bindings/arm/xen.txt @@ -11,10 +11,32 @@ the following properties: memory where the grant table should be mapped to, using an HYPERVISOR_memory_op hypercall. The memory region is large enough to map the whole grant table (it is larger or equal to gnttab_max_grant_frames()). + This property is unnecessary when booting Dom0 using ACPI. - interrupts: the interrupt used by Xen to inject event notifications. A GIC node is also required. + This property is unnecessary when booting Dom0 using ACPI. +To support UEFI on Xen ARM virtual platforms, Xen populates the FDT "uefi" node +under /hypervisor with following parameters: + +________________________________________________________________________________ +Name | Size | Description +================================================================================ +xen,uefi-system-table | 64-bit | Guest physical address of the UEFI System + | | Table. +-------------------------------------------------------------------------------- +xen,uefi-mmap-start | 64-bit | Guest physical address of the UEFI memory + | | map. +-------------------------------------------------------------------------------- +xen,uefi-mmap-size | 32-bit | Size in bytes of the UEFI memory map + | | pointed to in previous entry. +-------------------------------------------------------------------------------- +xen,uefi-mmap-desc-size | 32-bit | Size in bytes of each entry in the UEFI + | | memory map. +-------------------------------------------------------------------------------- +xen,uefi-mmap-desc-ver | 32-bit | Version of the mmap descriptor format. +-------------------------------------------------------------------------------- Example (assuming #address-cells = <2> and #size-cells = <2>): @@ -22,4 +44,17 @@ hypervisor { compatible = "xen,xen-4.3", "xen,xen"; reg = <0 0xb0000000 0 0x20000>; interrupts = <1 15 0xf08>; + uefi { + xen,uefi-system-table = <0xXXXXXXXX>; + xen,uefi-mmap-start = <0xXXXXXXXX>; + xen,uefi-mmap-size = <0xXXXXXXXX>; + xen,uefi-mmap-desc-size = <0xXXXXXXXX>; + xen,uefi-mmap-desc-ver = <0xXXXXXXXX>; + }; }; + +The format and meaning of the "xen,uefi-*" parameters are similar to those in +Documentation/arm/uefi.txt, which are provided by the regular UEFI stub. However +they differ because they are provided by the Xen hypervisor, together with a set +of UEFI runtime services implemented via hypercalls, see +http://xenbits.xen.org/docs/unstable/hypercall/x86_64/include,public,platform.h.html. diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 60872838f1ad..0a5b3b47f217 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -1,13 +1,14 @@ -* Broadcom SATA3 AHCI Controller for STB +* Broadcom SATA3 AHCI Controller SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: - compatible : should be one or more of - "brcm,bcm7425-ahci" - "brcm,bcm7445-ahci" - "brcm,sata3-ahci" + "brcm,bcm7425-ahci" + "brcm,bcm7445-ahci" + "brcm,bcm-nsp-ahci" + "brcm,sata3-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt new file mode 100644 index 000000000000..ce06435d28ed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -0,0 +1,36 @@ +* Amlogic GXBB Clock and Reset Unit + +The Amlogic GXBB clock controller generates and supplies clock to various +controllers within the SoC. + +Required Properties: + +- compatible: should be "amlogic,gxbb-clkc" +- reg: physical base address of the clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be +used in device tree sources. + +Example: Clock controller node: + + clkc: clock-controller@c883c000 { + #clock-cells = <1>; + compatible = "amlogic,gxbb-clkc"; + reg = <0x0 0xc883c000 0x0 0x3db>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart_AO: serial@c81004c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc81004c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc CLKID_CLK81>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt index 1bae8527eb9b..189467a7188a 100644 --- a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt +++ b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt @@ -14,6 +14,10 @@ Required properties: Optional properties: - clock-output-names : From common clock binding. +Some clocks that require special treatments are also handled by that +driver, with the compatibles: + - allwinner,sun4i-a10-pll3-2x-clk + Example: clock { compatible = "fixed-factor-clock"; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index fefb8023020f..394d725ac7e0 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -13,7 +13,8 @@ They provide the following functionalities: Required Properties: - compatible: Must be one of: - - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC + - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) + - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) - reg: Base address and length of the memory resource used by the CPG/MSSR block @@ -21,8 +22,8 @@ Required Properties: - clocks: References to external parent clocks, one entry for each entry in clock-names - clock-names: List of external parent clock names. Valid names are: - - "extal" (r8a7795) - - "extalr" (r8a7795) + - "extal" (r8a7795, r8a7796) + - "extalr" (r8a7795, r8a7796) - #clock-cells: Must be 2 - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 16ed18155160..da578ebdda28 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -17,6 +17,7 @@ Required Properties: - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2-W) MSTP gate clocks + - "renesas,r8a7792-mstp-clocks" for R8A7792 (R-Car V2H) MSTP gate clocks - "renesas,r8a7793-mstp-clocks" for R8A7793 (R-Car M2-N) MSTP gate clocks - "renesas,r8a7794-mstp-clocks" for R8A7794 (R-Car E2) MSTP gate clocks - "renesas,sh73a0-mstp-clocks" for SH73A0 (SH-MobileAG5) MSTP gate clocks diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index 2a9a8edc8f35..f8c05bb4116e 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -10,6 +10,7 @@ Required Properties: - compatible: Must be one of - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7792-cpg-clocks" for the r8a7792 CPG - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG and "renesas,rcar-gen2-cpg-clocks" as a fallback. diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt new file mode 100644 index 000000000000..cb91507ffb1e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -0,0 +1,24 @@ +Allwinner Clock Control Unit Binding +------------------------------------ + +Required properties : +- compatible: must contain one of the following compatible: + - "allwinner,sun8i-h3-ccu" + +- reg: Must contain the registers base address and length +- clocks: phandle to the oscillators feeding the CCU. Two are needed: + - "hosc": the high frequency oscillator (usually at 24MHz) + - "losc": the low frequency oscillator (usually at 32kHz) +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +ccu: clock@01c20000 { + compatible = "allwinner,sun8i-h3-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/dma/mv-xor-v2.txt b/Documentation/devicetree/bindings/dma/mv-xor-v2.txt new file mode 100644 index 000000000000..217a90eaabe7 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mv-xor-v2.txt @@ -0,0 +1,24 @@ +* Marvell XOR v2 engines + +Required properties: +- compatible: one of the following values: + "marvell,armada-7k-xor" + "marvell,xor-v2" +- reg: Should contain registers location and length (two sets) + the first set is the DMA registers + the second set is the global registers +- msi-parent: Phandle to the MSI-capable interrupt controller used for + interrupts. + +Optional properties: +- clocks: Optional reference to the clock used by the XOR engine. + +Example: + + xor0@400000 { + compatible = "marvell,xor-v2"; + reg = <0x400000 0x1000>, + <0x410000 0x1000>; + msi-parent = <&gic_v2m0>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt index 3cf0072d3141..a2b8bfaec43c 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -1,46 +1,96 @@ +Xilinx AXI VDMA engine, it does transfers between memory and video devices. +It can be configured to have one channel or two channels. If configured +as two channels, one is to transmit to the video device and another is +to receive from the video device. + Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream target devices. It can be configured to have one channel or two channels. If configured as two channels, one is to transmit to the device and another is to receive from the device. +Xilinx AXI CDMA engine, it does transfers between memory-mapped source +address and a memory-mapped destination address. + Required properties: -- compatible: Should be "xlnx,axi-dma-1.00.a" +- compatible: Should be "xlnx,axi-vdma-1.00.a" or "xlnx,axi-dma-1.00.a" or + "xlnx,axi-cdma-1.00.a"" - #dma-cells: Should be <1>, see "dmas" property below -- reg: Should contain DMA registers location and length. +- reg: Should contain VDMA registers location and length. +- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits). +- dma-ranges: Should be as the following <dma_addr cpu_addr max_len>. - dma-channel child node: Should have at least one channel and can have up to two channels per device. This node specifies the properties of each DMA channel (see child node properties below). +- clocks: Input clock specifier. Refer to common clock bindings. +- clock-names: List of input clocks + For VDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk" "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk" + For CDMA: + Required elements: "s_axi_lite_aclk", "m_axi_aclk" + FOR AXIDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axi_sg_aclk" + +Required properties for VDMA: +- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. Optional properties: -- xlnx,include-sg: Tells whether configured for Scatter-mode in +- xlnx,include-sg: Tells configured for Scatter-mode in the hardware. +Optional properties for AXI DMA: +- xlnx,mcdma: Tells whether configured for multi-channel mode in the hardware. +Optional properties for VDMA: +- xlnx,flush-fsync: Tells which channel to Flush on Frame sync. + It takes following values: + {1}, flush both channels + {2}, flush mm2s channel + {3}, flush s2mm channel Required child node properties: -- compatible: It should be either "xlnx,axi-dma-mm2s-channel" or +- compatible: + For VDMA: It should be either "xlnx,axi-vdma-mm2s-channel" or + "xlnx,axi-vdma-s2mm-channel". + For CDMA: It should be "xlnx,axi-cdma-channel". + For AXIDMA: It should be either "xlnx,axi-dma-mm2s-channel" or "xlnx,axi-dma-s2mm-channel". -- interrupts: Should contain per channel DMA interrupts. +- interrupts: Should contain per channel VDMA interrupts. - xlnx,datawidth: Should contain the stream data width, take values {32,64...1024}. -Option child node properties: -- xlnx,include-dre: Tells whether hardware is configured for Data +Optional child node properties: +- xlnx,include-dre: Tells hardware is configured for Data Realignment Engine. +Optional child node properties for VDMA: +- xlnx,genlock-mode: Tells Genlock synchronization is + enabled/disabled in hardware. +Optional child node properties for AXI DMA: +-dma-channels: Number of dma channels in child node. Example: ++++++++ -axi_dma_0: axidma@40400000 { - compatible = "xlnx,axi-dma-1.00.a"; +axi_vdma_0: axivdma@40030000 { + compatible = "xlnx,axi-vdma-1.00.a"; #dma_cells = <1>; - reg = < 0x40400000 0x10000 >; - dma-channel@40400000 { - compatible = "xlnx,axi-dma-mm2s-channel"; - interrupts = < 0 59 4 >; + reg = < 0x40030000 0x10000 >; + dma-ranges = <0x00000000 0x00000000 0x40000000>; + xlnx,num-fstores = <0x8>; + xlnx,flush-fsync = <0x1>; + xlnx,addrwidth = <0x20>; + clocks = <&clk 0>, <&clk 1>, <&clk 2>, <&clk 3>, <&clk 4>; + clock-names = "s_axi_lite_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk"; + dma-channel@40030000 { + compatible = "xlnx,axi-vdma-mm2s-channel"; + interrupts = < 0 54 4 >; xlnx,datawidth = <0x40>; } ; - dma-channel@40400030 { - compatible = "xlnx,axi-dma-s2mm-channel"; - interrupts = < 0 58 4 >; + dma-channel@40030030 { + compatible = "xlnx,axi-vdma-s2mm-channel"; + interrupts = < 0 53 4 >; xlnx,datawidth = <0x40>; } ; } ; @@ -49,7 +99,7 @@ axi_dma_0: axidma@40400000 { * DMA client Required properties: -- dmas: a list of <[DMA device phandle] [Channel ID]> pairs, +- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs, where Channel ID is '0' for write/tx and '1' for read/rx channel. - dma-names: a list of DMA channel names, one per "dmas" entry @@ -57,9 +107,9 @@ Required properties: Example: ++++++++ -dmatest_0: dmatest@0 { - compatible ="xlnx,axi-dma-test-1.00.a"; - dmas = <&axi_dma_0 0 - &axi_dma_0 1>; - dma-names = "dma0", "dma1"; +vdmatest_0: vdmatest@0 { + compatible ="xlnx,axi-vdma-test-1.00.a"; + dmas = <&axi_vdma_0 0 + &axi_vdma_0 1>; + dma-names = "vdma0", "vdma1"; } ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt deleted file mode 100644 index a1f2683c49bf..000000000000 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt +++ /dev/null @@ -1,107 +0,0 @@ -Xilinx AXI VDMA engine, it does transfers between memory and video devices. -It can be configured to have one channel or two channels. If configured -as two channels, one is to transmit to the video device and another is -to receive from the video device. - -Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream -target devices. It can be configured to have one channel or two channels. -If configured as two channels, one is to transmit to the device and another -is to receive from the device. - -Xilinx AXI CDMA engine, it does transfers between memory-mapped source -address and a memory-mapped destination address. - -Required properties: -- compatible: Should be "xlnx,axi-vdma-1.00.a" or "xlnx,axi-dma-1.00.a" or - "xlnx,axi-cdma-1.00.a"" -- #dma-cells: Should be <1>, see "dmas" property below -- reg: Should contain VDMA registers location and length. -- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits). -- dma-ranges: Should be as the following <dma_addr cpu_addr max_len>. -- dma-channel child node: Should have at least one channel and can have up to - two channels per device. This node specifies the properties of each - DMA channel (see child node properties below). -- clocks: Input clock specifier. Refer to common clock bindings. -- clock-names: List of input clocks - For VDMA: - Required elements: "s_axi_lite_aclk" - Optional elements: "m_axi_mm2s_aclk" "m_axi_s2mm_aclk", - "m_axis_mm2s_aclk", "s_axis_s2mm_aclk" - For CDMA: - Required elements: "s_axi_lite_aclk", "m_axi_aclk" - FOR AXIDMA: - Required elements: "s_axi_lite_aclk" - Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", - "m_axi_sg_aclk" - -Required properties for VDMA: -- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. - -Optional properties: -- xlnx,include-sg: Tells configured for Scatter-mode in - the hardware. -Optional properties for VDMA: -- xlnx,flush-fsync: Tells which channel to Flush on Frame sync. - It takes following values: - {1}, flush both channels - {2}, flush mm2s channel - {3}, flush s2mm channel - -Required child node properties: -- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or - "xlnx,axi-vdma-s2mm-channel". -- interrupts: Should contain per channel VDMA interrupts. -- xlnx,datawidth: Should contain the stream data width, take values - {32,64...1024}. - -Optional child node properties: -- xlnx,include-dre: Tells hardware is configured for Data - Realignment Engine. -Optional child node properties for VDMA: -- xlnx,genlock-mode: Tells Genlock synchronization is - enabled/disabled in hardware. - -Example: -++++++++ - -axi_vdma_0: axivdma@40030000 { - compatible = "xlnx,axi-vdma-1.00.a"; - #dma_cells = <1>; - reg = < 0x40030000 0x10000 >; - dma-ranges = <0x00000000 0x00000000 0x40000000>; - xlnx,num-fstores = <0x8>; - xlnx,flush-fsync = <0x1>; - xlnx,addrwidth = <0x20>; - clocks = <&clk 0>, <&clk 1>, <&clk 2>, <&clk 3>, <&clk 4>; - clock-names = "s_axi_lite_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", - "m_axis_mm2s_aclk", "s_axis_s2mm_aclk"; - dma-channel@40030000 { - compatible = "xlnx,axi-vdma-mm2s-channel"; - interrupts = < 0 54 4 >; - xlnx,datawidth = <0x40>; - } ; - dma-channel@40030030 { - compatible = "xlnx,axi-vdma-s2mm-channel"; - interrupts = < 0 53 4 >; - xlnx,datawidth = <0x40>; - } ; -} ; - - -* DMA client - -Required properties: -- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs, - where Channel ID is '0' for write/tx and '1' for read/rx - channel. -- dma-names: a list of DMA channel names, one per "dmas" entry - -Example: -++++++++ - -vdmatest_0: vdmatest@0 { - compatible ="xlnx,axi-vdma-test-1.00.a"; - dmas = <&axi_vdma_0 0 - &axi_vdma_0 1>; - dma-names = "vdma0", "vdma1"; -} ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt new file mode 100644 index 000000000000..a784cdd94790 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt @@ -0,0 +1,27 @@ +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, +memory to device and device to memory transfers. It also has flow +control and rate control support for slave/peripheral dma access. + +Required properties: +- compatible : Should be "xlnx,zynqmp-dma-1.0" +- reg : Memory map for gdma/adma module access. +- interrupt-parent : Interrupt controller the interrupt is routed through +- interrupts : Should contain DMA channel interrupt. +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 +- clock-names : List of input clocks "clk_main", "clk_apb" + (see clock bindings for details) + +Optional properties: +- dma-coherent : Present if dma operations are coherent. + +Example: +++++++++ +fpd_dma_chan1: dma@fd500000 { + compatible = "xlnx,zynqmp-dma-1.0"; + reg = <0x0 0xFD500000 0x1000>; + interrupt-parent = <&gic>; + interrupts = <0 117 4>; + clock-names = "clk_main", "clk_apb"; + xlnx,bus-width = <128>; + dma-coherent; +}; diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index e27341f8a4c7..7f3d94ae81ff 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -46,7 +46,8 @@ Optional properties: The second cell represents the MICBIAS to be used. The third cell represents the value of the micd-pol-gpio pin. - - wlf,gpsw : Settings for the general purpose switch + - wlf,gpsw : Settings for the general purpose switch, set as one of the + ARIZONA_GPSW_XXX defines. Example: diff --git a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt index 94ae9f82dcf8..fd42e7280f72 100644 --- a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -1,7 +1,7 @@ * ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs Required properties: -- compatible: Should contain "cirrus,clps711x-mctrl-gpio". +- compatible: Should contain "cirrus,ep7209-mctrl-gpio". - gpio-controller: Marks the device node as a gpio controller. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify the gpio polarity: @@ -11,7 +11,7 @@ Required properties: Example: sysgpio: sysgpio { compatible = "cirrus,ep7312-mctrl-gpio", - "cirrus,clps711x-mctrl-gpio"; + "cirrus,ep7209-mctrl-gpio"; gpio-controller; #gpio-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt index e0d0446a6b78..0a304ad29d81 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -1,7 +1,7 @@ Cirrus Logic CLPS711X GPIO controller Required properties: -- compatible: Should be "cirrus,clps711x-gpio" +- compatible: Should be "cirrus,ep7209-gpio" - reg: Physical base GPIO controller registers location and length. There should be two registers, first is DATA register, the second is DIRECTION. @@ -21,7 +21,7 @@ aliases { }; porta: gpio@80000000 { - compatible = "cirrus,clps711x-gpio"; + compatible = "cirrus,ep7312-gpio","cirrus,ep7209-gpio"; reg = <0x80000000 0x1>, <0x80000040 0x1>; gpio-controller; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max77620.txt b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt new file mode 100644 index 000000000000..410e716fd3d2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt @@ -0,0 +1,25 @@ +GPIO driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Required properties: +------------------- +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +For more details, please refer generic GPIO DT binding document +<devicetree/bindings/gpio/gpio.txt>. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + compatible = "maxim,max77620"; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 6b4a98f74be3..08dd15f89ba9 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -21,6 +21,7 @@ Required properties: maxim,max7313 maxim,max7315 ti,pca6107 + ti,pca9536 ti,tca6408 ti,tca6416 ti,tca6424 diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt new file mode 100644 index 000000000000..928ed4f43907 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -0,0 +1,47 @@ +* Oxford Semiconductor OXNAS SoC GPIO Controller + +Please refer to gpio.txt for generic information regarding GPIO bindings. + +Required properties: + - compatible: "oxsemi,ox810se-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - gpio-ranges: Interaction with the PINCTRL subsystem, it also specifies the + gpio base and count, should be in the format of numeric-gpio-range as + specified in the gpio.txt file. + +Example: + +gpio0: gpio@0 { + compatible = "oxsemi,ox810se-gpio"; + reg = <0x000000 0x100000>; + interrupts = <21>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pinctrl 0 0 32>; +}; + +keys { + ... + + button-esc { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f60e2f477e93..8da26b35b5c3 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -7,6 +7,7 @@ Required Properties: - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. + - "renesas,gpio-r8a7792": for R8A7792 (R-Car V2H) compatible GPIO controller. - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. diff --git a/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt new file mode 100644 index 000000000000..59b38557f1bb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt @@ -0,0 +1,14 @@ +APM X-Gene hwmon driver + +APM X-Gene SOC sensors are accessed over the "SLIMpro" mailbox. + +Required properties : + - compatible : should be "apm,xgene-slimpro-hwmon" + - mboxes : use the label reference for the mailbox as the first parameter. + The second parameter is the channel number. + +Example : + hwmonslimpro { + compatible = "apm,xgene-slimpro-hwmon"; + mboxes = <&mailbox 7>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/jc42.txt b/Documentation/devicetree/bindings/hwmon/jc42.txt new file mode 100644 index 000000000000..07a250498fbb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/jc42.txt @@ -0,0 +1,42 @@ +Properties for Jedec JC-42.4 compatible temperature sensors + +Required properties: +- compatible: May include a device-specific string consisting of the + manufacturer and the name of the chip. A list of supported + chip names follows. + Must include "jedec,jc-42.4-temp" for any Jedec JC-42.4 + compatible temperature sensor. + + Supported chip names: + adi,adt7408 + atmel,at30ts00 + atmel,at30tse004 + onnn,cat6095 + onnn,cat34ts02 + maxim,max6604 + microchip,mcp9804 + microchip,mcp9805 + microchip,mcp9808 + microchip,mcp98243 + microchip,mcp98244 + microchip,mcp9843 + nxp,se97 + nxp,se98 + st,stts2002 + st,stts2004 + st,stts3000 + st,stts424 + st,stts424e + idt,tse2002 + idt,tse2004 + idt,ts3000 + idt,ts3001 + +- reg: I2C address + +Example: + +temp-sensor@1a { + compatible = "jedec,jc-42.4-temp"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index 0b4a85fe2d86..bbc5a1ed5fa1 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -6,10 +6,20 @@ RK3xxx SoCs. Required properties : - reg : Offset and length of the register set for the device - - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c", - "rockchip,rk3228-i2c" or "rockchip,rk3288-i2c". + - compatible: should be one of the following: + - "rockchip,rk3066-i2c": for rk3066 + - "rockchip,rk3188-i2c": for rk3188 + - "rockchip,rk3228-i2c": for rk3228 + - "rockchip,rk3288-i2c": for rk3288 + - "rockchip,rk3399-i2c": for rk3399 - interrupts : interrupt number - - clocks : parent clock + - clocks: See ../clock/clock-bindings.txt + - For older hardware (rk3066, rk3188, rk3228, rk3288): + - There is one clock that's used both to derive the functional clock + for the device and as the bus clock. + - For newer hardware (rk3399): specified by name + - "i2c": This is used to derive the functional clock. + - "pclk": This is the bus clock. Required on RK3066, RK3188 : diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index c8d977ed847f..f31b2ad1552b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -62,6 +62,13 @@ wants to support one of the below features, it should adapt the bindings below. - wakeup-source device can be used as a wakeup source. +- reg + I2C slave addresses + +- reg-names + Names of map programmable addresses. + It can contain any map needing another address than default one. + Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first interrupt if not using interrupt names) as primary interrupt for the slave. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 539874490492..5c70ce9c1954 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -56,12 +56,77 @@ maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4531-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4532-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4532-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4532-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4532-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4541-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4541-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4541-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4541-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4542-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4542-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4542-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4542-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4551-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4551-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4551-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4551-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4552-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4552-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4552-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4552-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4561-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4561-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4561-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4561-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4562-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4562-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4562-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4562-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4631-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4631-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4631-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4631-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4632-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4632-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4632-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4632-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4641-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4641-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4641-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4641-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4642-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4642-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4642-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4642-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4651-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4651-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4651-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4651-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4652-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4652-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4652-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4652-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4661-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4661-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4661-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4661-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4662-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4662-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4662-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4662-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor national,lm85 Temperature sensor with integrated fan control national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface nuvoton,npct501 i2c trusted platform module (TPM) +nuvoton,npct601 i2c trusted platform module (TPM2) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar @@ -81,10 +146,10 @@ samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply -st-micro,24c256 i2c serial eeprom (24cxx) -stm,m41t00 Serial Access TIMEKEEPER -stm,m41t62 Serial real-time clock (RTC) with alarm -stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +st,24c256 i2c serial eeprom (24cxx) +st,m41t00 Serial real-time clock (RTC) +st,m41t62 Serial real-time clock (RTC) with alarm +st,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,ads7828 8-Channels, 12-bit ADC ti,ads7830 8-Channels, 8-bit ADC diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt new file mode 100644 index 000000000000..caaaed765ce4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt @@ -0,0 +1,41 @@ +* Broadcom's IPROC Static ADC controller + +Broadcom iProc ADC controller has 8 channels 10bit ADC. +Allows user to convert analog input voltage values to digital. + +Required properties: + +- compatible: Must be "brcm,iproc-static-adc" + +- adc-syscon: Handler of syscon node defining physical base address of the + controller and length of memory mapped region. + +- #io-channel-cells = <1>; As ADC has multiple outputs + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- io-channel-ranges: + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- clocks: Clock used for this block. + +- clock-names: Clock name should be given as tsc_clk. + +- interrupts: interrupt line number. + +For example: + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + adc: adc@180a6000 { + compatible = "brcm,iproc-static-adc"; + adc-syscon = <&ts_adc_syscon>; + #io-channel-cells = <1>; + io-channel-ranges; + clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/max1363.txt b/Documentation/devicetree/bindings/iio/adc/max1363.txt new file mode 100644 index 000000000000..94a9011dd860 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1363.txt @@ -0,0 +1,63 @@ +* Maxim 1x3x/136x/116xx Analog to Digital Converter (ADC) + +The node for this driver must be a child node of a I2C controller, hence +all mandatory properties for your controller must be specified. See directory: + + Documentation/devicetree/bindings/i2c + +for more details. + +Required properties: + - compatible: Should be one of + "maxim,max1361" + "maxim,max1362" + "maxim,max1363" + "maxim,max1364" + "maxim,max1036" + "maxim,max1037" + "maxim,max1038" + "maxim,max1039" + "maxim,max1136" + "maxim,max1137" + "maxim,max1138" + "maxim,max1139" + "maxim,max1236" + "maxim,max1237" + "maxim,max1238" + "maxim,max1239" + "maxim,max11600" + "maxim,max11601" + "maxim,max11602" + "maxim,max11603" + "maxim,max11604" + "maxim,max11605" + "maxim,max11606" + "maxim,max11607" + "maxim,max11608" + "maxim,max11609" + "maxim,max11610" + "maxim,max11611" + "maxim,max11612" + "maxim,max11613" + "maxim,max11614" + "maxim,max11615" + "maxim,max11616" + "maxim,max11617" + "maxim,max11644" + "maxim,max11645" + "maxim,max11646" + "maxim,max11647" + - reg: Should contain the ADC I2C address + +Optional properties: + - vcc-supply: phandle to the regulator that provides power to the ADC. + - vref-supply: phandle to the regulator for ADC reference voltage. + - interrupts: IRQ line for the ADC. If not used the driver will use + polling. + +Example: +adc: max11644@36 { + compatible = "maxim,max11644"; + reg = <0x36>; + vref-supply = <&adc_vref>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt new file mode 100644 index 000000000000..2962bd9a2b3d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific EC-SM OEM sensor + +http://www.atlas-scientific.com/_files/_datasheets/_oem/EC_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,ec-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@64 { + compatible = "atlas,ec-sm"; + reg = <0x64>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5755.txt b/Documentation/devicetree/bindings/iio/dac/ad5755.txt new file mode 100644 index 000000000000..f0bbd7e1029b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5755.txt @@ -0,0 +1,124 @@ +* Analog Device AD5755 IIO Multi-Channel DAC Linux Driver + +Required properties: + - compatible: Has to contain one of the following: + adi,ad5755 + adi,ad5755-1 + adi,ad5757 + adi,ad5735 + adi,ad5737 + + - reg: spi chip select number for the device + - spi-cpha or spi-cpol: is the only modes that is supported + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +See include/dt-bindings/iio/ad5755.h + - adi,ext-dc-dc-compenstation-resistor: boolean set if the hardware have an + external resistor and thereby bypasses + the internal compensation resistor. + - adi,dc-dc-phase: + Valid values for DC DC Phase control is: + 0: All dc-to-dc converters clock on the same edge. + 1: Channel A and Channel B clock on the same edge, + Channel C and Channel D clock on opposite edges. + 2: Channel A and Channel C clock on the same edge, + Channel B and Channel D clock on opposite edges. + 3: Channel A, Channel B, Channel C, and Channel D + clock 90 degrees out of phase from each other. + - adi,dc-dc-freq-hz: + Valid values for DC DC frequency is [Hz]: + 250000 + 410000 + 650000 + - adi,dc-dc-max-microvolt: + Valid values for the maximum allowed Vboost voltage supplied by + the dc-to-dc converter is: + 23000000 + 24500000 + 27000000 + 29500000 + +Optional for every channel: + - adi,mode: + Valid values for DAC modes is: + 0: 0 V to 5 V voltage range. + 1: 0 V to 10 V voltage range. + 2: Plus minus 5 V voltage range. + 3: Plus minus 10 V voltage range. + 4: 4 mA to 20 mA current range. + 5: 0 mA to 20 mA current range. + 6: 0 mA to 24 mA current range. + - adi,ext-current-sense-resistor: boolean set if the hardware a external + current sense resistor. + - adi,enable-voltage-overrange: boolean enable voltage overrange + - adi,slew: Array of slewrate settings should contain 3 fields: + 1: Should be either 0 or 1 in order to enable or disable slewrate. + 2: Slew rate settings: + Valid values for the slew rate update frequency: + 64000 + 32000 + 16000 + 8000 + 4000 + 2000 + 1000 + 500 + 250 + 125 + 64 + 32 + 16 + 8 + 4 + 0 + 3: Slew step size: + Valid values for the step size LSBs: + 1 + 2 + 4 + 16 + 32 + 64 + 128 + 256 + +Example: +dac@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "adi,ad5755"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + adi,dc-dc-phase = <0>; + adi,dc-dc-freq-hz = <410000>; + adi,dc-dc-max-microvolt = <23000000>; + channel@0 { + reg = <0>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@1 { + reg = <1>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@2 { + reg = <2>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@3 { + reg = <3>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt index d7a6deb6b21e..c7198a03c906 100644 --- a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt +++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt @@ -1,7 +1,11 @@ -BMP085/BMP18x digital pressure sensors +BMP085/BMP18x/BMP28x digital pressure sensors Required properties: -- compatible: bosch,bmp085 +- compatible: must be one of: + "bosch,bmp085" + "bosch,bmp180" + "bosch,bmp280" + "bosch,bme280" Optional properties: - chip-id: configurable chip id for non-default chip revisions @@ -10,6 +14,10 @@ Optional properties: value range is 0-3 with rising sensitivity. - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ +- reset-gpios: a GPIO line handling reset of the sensor: as the line is + active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) +- vddd-supply: digital voltage regulator (see regulator/regulator.txt) +- vdda-supply: analog voltage regulator (see regulator/regulator.txt) Example: @@ -21,4 +29,7 @@ pressure@77 { default-oversampling = <2>; interrupt-parent = <&gpio0>; interrupts = <25 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + vddd-supply = <&foo>; + vdda-supply = <&bar>; }; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index 5844cf72862d..e41fe340162b 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -64,3 +64,4 @@ Pressure sensors: - st,lps001wp-press - st,lps25h-press - st,lps331ap-press +- st,lps22hb-press diff --git a/Documentation/devicetree/bindings/input/atmel,captouch.txt b/Documentation/devicetree/bindings/input/atmel,captouch.txt new file mode 100644 index 000000000000..fe9ee5c53bcc --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,captouch.txt @@ -0,0 +1,36 @@ +Device tree bindings for Atmel capacitive touch device, typically +an Atmel touch sensor connected to AtmegaXX MCU running firmware +based on Qtouch library. + +The node for this device must be a child of a I2C controller node, as the +device communicates via I2C. + +Required properties: + + compatible: Must be "atmel,captouch". + reg: The I2C slave address of the device. + interrupts: Property describing the interrupt line the device + is connected to. The device only has one interrupt + source. + linux,keycodes: Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 8 entries. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + +Example: + + atmel-captouch@51 { + compatible = "atmel,captouch"; + reg = <0x51>; + interrupt-parent = <&tlmm>; + interrupts = <67 IRQ_TYPE_EDGE_FALLING>; + linux,keycodes = <BTN_0>, <BTN_1>, + <BTN_2>, <BTN_3>, + <BTN_4>, <BTN_5>, + <BTN_6>, <BTN_7>; + autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt new file mode 100644 index 000000000000..5b6232db7c61 --- /dev/null +++ b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt @@ -0,0 +1,20 @@ +Raydium I2C touchscreen + +Required properties: +- compatible: must be "raydium,rm32380" +- reg: The I2C address of the device +- interrupt-parent: the phandle for the interrupt controller +- interrupts: interrupt to which the chip is connected + See ../interrupt-controller/interrupts.txt +Optional properties: +- avdd-supply: analog power supply needed to power device +- vccio-supply: IO Power source +- reset-gpios: reset gpio the chip is connected to. + +Example: + touchscreen@39 { + compatible = "raydium,rm32380"; + reg = <0x39>; + interrupt-parent = <&gpio>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt index 95fa715c6046..ec908b91fd90 100644 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt @@ -22,6 +22,15 @@ See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - syna,reset-delay-ms: The number of milliseconds to wait after resetting the device. +- syna,startup-delay-ms: The number of milliseconds to wait after powering on + the device. + +- vdd-supply: VDD power supply. +See ../regulator/regulator.txt + +- vio-supply: VIO power supply +See ../regulator/regulator.txt + Function Parameters: Parameters specific to RMI functions are contained in child nodes of the rmi device node. Documentation for the parameters of each function can be found in: diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 793c20ff8fcc..5393e2a45a42 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -21,6 +21,7 @@ Main node required properties: "arm,pl390" "arm,tc11mp-gic" "brcm,brahma-b15-gic" + "nvidia,tegra210-agic" "qcom,msm-8660-qgic" "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller @@ -68,7 +69,7 @@ Optional "ic_clk" (for "arm,arm11mp-gic") "PERIPHCLKEN" (for "arm,cortex-a15-gic") "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") - "clk" (for "arm,gic-400") + "clk" (for "arm,gic-400" and "nvidia,tegra210") "gclk" (for "arm,pl390") - power-domains : A phandle and PM domain specifier as defined by bindings of diff --git a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt new file mode 100644 index 000000000000..6c6e85324b9d --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt @@ -0,0 +1,22 @@ +Aspeed Vectored Interrupt Controller + +These bindings are for the Aspeed AST2400 interrupt controller register layout. +The SoC has an legacy register layout, but this driver does not support that +mode of operation. + +Required properties: + +- compatible : should be "aspeed,ast2400-vic". + +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +Example: + + vic: interrupt-controller@1e6c0080 { + compatible = "aspeed,ast2400-vic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1e6c0080 0x80>; + }; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index af10678ea2f6..93ef6e6e43b5 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -26,7 +26,9 @@ Optional properties for child nodes: "default-on" - LED will turn on (but for leds-gpio see "default-state" property in Documentation/devicetree/bindings/gpio/led.txt) "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity + "disk-activity" - LED indicates disk activity + "ide-disk" - LED indicates IDE disk activity (deprecated), + in new implementations use "disk-activity" "timer" - LED flashes at a fixed, configurable rate - led-max-microamp : Maximum LED supply current in microamperes. This property diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index cbbeb1850910..5b1b43a64265 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -33,9 +33,9 @@ Examples: leds { compatible = "gpio-leds"; hdd { - label = "IDE Activity"; + label = "Disk Activity"; gpios = <&mcu_pio 0 GPIO_ACTIVE_LOW>; - linux,default-trigger = "ide-disk"; + linux,default-trigger = "disk-activity"; }; fault { diff --git a/Documentation/devicetree/bindings/leds/leds-pca9532.txt b/Documentation/devicetree/bindings/leds/leds-pca9532.txt new file mode 100644 index 000000000000..198f3ba0e01f --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pca9532.txt @@ -0,0 +1,39 @@ +*NXP - pca9532 PWM LED Driver + +The PCA9532 family is SMBus I/O expander optimized for dimming LEDs. +The PWM support 256 steps. + +Required properties: + - compatible: + "nxp,pca9530" + "nxp,pca9531" + "nxp,pca9532" + "nxp,pca9533" + - reg - I2C slave address + +Each led is represented as a sub-node of the nxp,pca9530. + +Optional sub-node properties: + - label: see Documentation/devicetree/bindings/leds/common.txt + - type: Output configuration, see dt-bindings/leds/leds-pca9532.h (default NONE) + - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: + #include <dt-bindings/leds/leds-pca9532.h> + + leds: pca9530@60 { + compatible = "nxp,pca9530"; + reg = <0x60>; + + red-power { + label = "pca:red:power"; + type = <PCA9532_TYPE_LED>; + }; + green-power { + label = "pca:green:power"; + type = <PCA9532_TYPE_LED>; + }; + }; + +For more product information please see the link below: +http://nxp.com/documents/data_sheet/PCA9532.pdf diff --git a/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt new file mode 100644 index 000000000000..411ccf421584 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt @@ -0,0 +1,23 @@ +The PDC driver manages data transfer to and from various offload engines +on some Broadcom SoCs. An SoC may have multiple PDC hardware blocks. There is +one device tree entry per block. + +Required properties: +- compatible : Should be "brcm,iproc-pdc-mbox". +- reg: Should contain PDC registers location and length. +- interrupts: Should contain the IRQ line for the PDC. +- #mbox-cells: 1 +- brcm,rx-status-len: Length of metadata preceding received frames, in bytes. + +Optional properties: +- brcm,use-bcm-hdr: present if a BCM header precedes each frame. + +Example: + pdc0: iproc-pdc0@0x612c0000 { + compatible = "brcm,iproc-pdc-mbox"; + reg = <0 0x612c0000 0 0x445>; /* PDC FS0 regs */ + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; /* one cell per mailbox channel */ + brcm,rx-status-len = <32>; + brcm,use-bcm-hdr; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt new file mode 100644 index 000000000000..59a47a5b924b --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -0,0 +1,59 @@ +Mediatek Video Codec + +Mediatek Video Codec is the video codec hw present in Mediatek SoCs which +supports high resolution encoding functionalities. + +Required properties: +- compatible : "mediatek,mt8173-vcodec-enc" for encoder +- reg : Physical base address of the video codec registers and length of + memory mapped region. +- interrupts : interrupt number to the cpu. +- mediatek,larb : must contain the local arbiters in the current Socs. +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property. +- clock-names: encoder must contain "venc_sel_src", "venc_sel", +- "venc_lt_sel_src", "venc_lt_sel". +- iommus : should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,vpu : the node of video processor unit + +Example: +vcodec_enc: vcodec@0x18002000 { + compatible = "mediatek,mt8173-vcodec-enc"; + reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ + <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb3>, + <&larb5>; + iommus = <&iommu M4U_PORT_VENC_RCPU>, + <&iommu M4U_PORT_VENC_REC>, + <&iommu M4U_PORT_VENC_BSDMA>, + <&iommu M4U_PORT_VENC_SV_COMV>, + <&iommu M4U_PORT_VENC_RD_COMV>, + <&iommu M4U_PORT_VENC_CUR_LUMA>, + <&iommu M4U_PORT_VENC_CUR_CHROMA>, + <&iommu M4U_PORT_VENC_REF_LUMA>, + <&iommu M4U_PORT_VENC_REF_CHROMA>, + <&iommu M4U_PORT_VENC_NBM_RDMA>, + <&iommu M4U_PORT_VENC_NBM_WDMA>, + <&iommu M4U_PORT_VENC_RCPU_SET2>, + <&iommu M4U_PORT_VENC_REC_FRM_SET2>, + <&iommu M4U_PORT_VENC_BSDMA_SET2>, + <&iommu M4U_PORT_VENC_SV_COMA_SET2>, + <&iommu M4U_PORT_VENC_RD_COMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>, + <&iommu M4U_PORT_VENC_REF_LUMA_SET2>, + <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_UNIVPLL1_D2>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "venc_sel_src", + "venc_sel", + "venc_lt_sel_src", + "venc_lt_sel"; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vpu.txt b/Documentation/devicetree/bindings/media/mediatek-vpu.txt new file mode 100644 index 000000000000..2a5bac37f9a2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vpu.txt @@ -0,0 +1,31 @@ +* Mediatek Video Processor Unit + +Video Processor Unit is a HW video controller. It controls HW Codec including +H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color convert). + +Required properties: + - compatible: "mediatek,mt8173-vpu" + - reg: Must contain an entry for each entry in reg-names. + - reg-names: Must include the following entries: + "tcm": tcm base + "cfg_reg": Main configuration registers base + - interrupts: interrupt number to the cpu. + - clocks : clock name from clock manager + - clock-names: must be main. It is the main clock of VPU + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for VPU extended memory; if not present, VPU may be located + anywhere in the memory + +Example: + vpu: vpu@10020000 { + compatible = "mediatek,mt8173-vpu"; + reg = <0 0x10020000 0 0x30000>, + <0 0x10050000 0 0x100>; + reg-names = "tcm", "cfg_reg"; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen TOP_SCP_SEL>; + clock-names = "main"; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt new file mode 100644 index 000000000000..6a12960609d8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -0,0 +1,32 @@ +Renesas R-Car Frame Compression Processor (FCP) +----------------------------------------------- + +The FCP is a companion module of video processing modules in the Renesas R-Car +Gen3 SoCs. It provides data compression and decompression, data caching, and +conversion of AXI transactions in order to reduce the memory bandwidth. + +There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP +for FDP (FCPF). Their configuration and behaviour depend on the module they +are paired with. These DT bindings currently support the FCPV only. + + - compatible: Must be one or more of the following + + - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP' + - "renesas,fcpv" for generic compatible 'FCP for VSP' + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + + - reg: the register base and size for the device registers + - clocks: Reference to the functional clock + + +Device node example +------------------- + + fcpvd1: fcp@fea2f000 { + compatible = "renesas,r8a7795-fcpv", "renesas,fcpv"; + reg = <0 0xfea2f000 0 0x200>; + clocks = <&cpg CPG_MOD 602>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 627405abd144..9b695bcbf219 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -14,6 +14,11 @@ Required properties: - interrupts: VSP interrupt specifier. - clocks: A phandle + clock-specifier pair for the VSP functional clock. +Optional properties: + + - renesas,fcp: A phandle referencing the FCP that handles memory accesses + for the VSP. Not needed on Gen2, mandatory on Gen3. + Example: R8A7790 (R-Car H2) VSP1-S node diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt new file mode 100644 index 000000000000..925ab4d72eaa --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -0,0 +1,31 @@ +* Samsung HDMI CEC driver + +The HDMI CEC module is present is Samsung SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "samsung,s5p-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "hdmicec", + corresponding to entry in the clocks property. + - samsung,syscon-phandle - phandle to the PMU system controller + +Example: + +hdmicec: cec@100B0000 { + compatible = "samsung,s5p-cec"; + reg = <0x100B0000 0x200>; + interrupts = <0 114 0>; + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + samsung,syscon-phandle = <&pmu_system_controller>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 2d5787eac91a..92c94f5ecbf1 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -21,15 +21,18 @@ Required properties: - clock-names : from common clock binding: must contain "mfc", corresponding to entry in the clocks property. - - samsung,mfc-r : Base address of the first memory bank used by MFC - for DMA contiguous memory allocation and its size. - - - samsung,mfc-l : Base address of the second memory bank used by MFC - for DMA contiguous memory allocation and its size. - Optional properties: - power-domains : power-domain property defined with a phandle to respective power domain. + - memory-region : from reserved memory binding: phandles to two reserved + memory regions, first is for "left" mfc memory bus interfaces, + second if for the "right" mfc memory bus, used when no SYSMMU + support is available + +Obsolete properties: + - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region + property instead + Example: SoC specific DT entry: @@ -43,9 +46,29 @@ mfc: codec@13400000 { clock-names = "mfc"; }; +Reserved memory specific DT entry for given board (see reserved memory binding +for more information): + +reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mfc_left: region@51000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x51000000 0x800000>; + }; + + mfc_right: region@43000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x43000000 0x800000>; + }; +}; + Board specific DT entry: codec@13400000 { - samsung,mfc-r = <0x43000000 0x800000>; - samsung,mfc-l = <0x51000000 0x800000>; + memory-region = <&mfc_left>, <&mfc_right>; }; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index d20b1034e967..585a95546288 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -22,6 +22,11 @@ Optional properties: AXP152/20X: range: 750-1875, Default: 1.5 MHz AXP22X/80X: range: 1800-4050, Default: 3 MHz +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not. + - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -79,6 +84,7 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator AXP809 regulators, type, and corresponding input supply names: diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 1857f4a6b9a9..9554292dc6cb 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -8,10 +8,13 @@ Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: - buck0 : regulator BUCK0 - buck1 : regulator BUCK1 - buck2 : regulator BUCK2 - buck3 : regulator BUCK3 + buck1 : regulator BUCK CORE + buck2 : regulator BUCK PRO + buck3 : regulator BUCK MEM + buck4 : regulator BUCK PERI + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 ldo4 : regulator LDO4 ldo5 : regulator LDO5 ldo6 : regulator LDO6 @@ -19,9 +22,6 @@ Sub-nodes: ldo8 : regulator LDO8 ldo9 : regulator LDO9 ldo10 : regulator LDO10 - ldo11 : regulator LDO11 - ldo12 : regulator LDO12 - ldo13 : regulator LDO13 The bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */ reg = <0x48>; regulators { - buck0 { + buck1 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck1 { + buck2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck2 { + buck3 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; - buck3 { + buck4 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 937785a3eddc..9e6770b105c9 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,18 +1,21 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618 is a power management IC family which integrates +3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and +a watchdog timer. The RN5T618 provides additionally a Li-ion battery +charger, fuel gauge and an ADC. It can be controlled through an I2C +interface. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/misc/ramoops.txt b/Documentation/devicetree/bindings/misc/ramoops.txt new file mode 100644 index 000000000000..cd02cec67d38 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ramoops.txt @@ -0,0 +1,48 @@ +Ramoops oops/panic logger +========================= + +ramoops provides persistent RAM storage for oops and panics, so they can be +recovered after a reboot. It is a backend to pstore, so this node is named +"ramoops" after the backend, rather than "pstore" which is the subsystem. + +Parts of this storage may be set aside for other persistent log buffers, such +as kernel log messages, or for optional ECC error-correction data. The total +size of these optional buffers must fit in the reserved region. + +Any remaining space will be used for a circular buffer of oops and panic +records. These records have a configurable size, with a size of 0 indicating +that they should be disabled. + +At least one of "record-size", "console-size", "ftrace-size", or "pmsg-size" +must be set non-zero, but are otherwise optional as listed below. + + +Required properties: + +- compatible: must be "ramoops" + +- memory-region: phandle to a region of memory that is preserved between + reboots + + +Optional properties: + +- ecc-size: enables ECC support and specifies ECC buffer size in bytes + (defaults to 0: no ECC) + +- record-size: maximum size in bytes of each dump done on oops/panic + (defaults to 0: disabled) + +- console-size: size in bytes of log buffer reserved for kernel messages + (defaults to 0: disabled) + +- ftrace-size: size in bytes of log buffer reserved for function tracing and + profiling (defaults to 0: disabled) + +- pmsg-size: size in bytes of log buffer reserved for userspace messages + (defaults to 0: disabled) + +- unbuffered: if present, use unbuffered mappings to map the reserved region + (defaults to buffered mappings) + +- no-dump-oops: if present, only dump panics (defaults to panics and oops) diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 31b35c3a5e47..3404afa9b938 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -9,8 +9,12 @@ Device Tree Bindings for the Arasan SDHCI Controller [4] Documentation/devicetree/bindings/phy/phy-bindings.txt Required Properties: - - compatible: Compatibility string. Must be 'arasan,sdhci-8.9a' or - 'arasan,sdhci-4.9a' or 'arasan,sdhci-5.1' + - compatible: Compatibility string. One of: + - "arasan,sdhci-8.9a": generic Arasan SDHCI 8.9a PHY + - "arasan,sdhci-4.9a": generic Arasan SDHCI 4.9a PHY + - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY + - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY + For this device it is strongly suggested to include arasan,soc-ctl-syscon. - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" @@ -22,6 +26,17 @@ Required Properties for "arasan,sdhci-5.1": - phys: From PHY bindings: Phandle for the Generic PHY for arasan. - phy-names: MUST be "phy_arasan". +Optional Properties: + - arasan,soc-ctl-syscon: A phandle to a syscon device (see ../mfd/syscon.txt) + used to access core corecfg registers. Offsets of registers in this + syscon are determined based on the main compatible string for the device. + - clock-output-names: If specified, this will be the name of the card clock + which will be exposed by this device. Required if #clock-cells is + specified. + - #clock-cells: If specified this should be the value <0>. With this property + in place we will export a clock representing the Card Clock. This clock + is expected to be consumed by our PHY. You must also specify + Example: sdhci@e0100000 { compatible = "arasan,sdhci-8.9a"; @@ -42,3 +57,19 @@ Example: phys = <&emmc_phy>; phy-names = "phy_arasan"; } ; + + sdhci: sdhci@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0x0 0xfe330000 0x0 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + arasan,soc-ctl-syscon = <&grf>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clock-output-names = "emmc_cardclock"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + #clock-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt deleted file mode 100644 index 59476fbdbfa1..000000000000 --- a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt +++ /dev/null @@ -1,18 +0,0 @@ -Broadcom BCM2835 SDHCI controller - -This file documents differences between the core properties described -by mmc.txt and the properties that represent the BCM2835 controller. - -Required properties: -- compatible : Should be "brcm,bcm2835-sdhci". -- clocks : The clock feeding the SDHCI controller. - -Example: - -sdhci: sdhci { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clk_mmc>; - bus-width = <4>; -}; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt new file mode 100644 index 000000000000..82847174c37d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt @@ -0,0 +1,36 @@ +* BROADCOM BRCMSTB/BMIPS SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-brcmstb driver. + +NOTE: The driver disables all UHS speed modes by default and depends +on Device Tree properties to enable them for SoC/Board combinations +that support them. + +Required properties: +- compatible: "brcm,bcm7425-sdhci" + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + + sdhci@f03e0100 { + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0000 0x100>; + interrupts = <0x0 0x26 0x0>; + sdhci,auto-cmd12; + clocks = <&sw_sdio>; + sd-uhs-sdr50; + sd-uhs-ddr50; + }; + + sdhci@f03e0300 { + non-removable; + bus-width = <0x8>; + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0200 0x100>; + interrupts = <0x0 0x27 0x0>; + sdhci,auto-cmd12; + clocks = <sw_sdio>; + mmc-hs200-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index dca56d6248f5..3e29050ec769 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -28,6 +28,8 @@ Optional properties: transparent level shifters on the outputs of the controller. Two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. +- fsl,tuning-start-tap: Specify the start dealy cell point when send first CMD19 + in tuning procedure. - fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure. The uSDHC use one delay cell as default increasing step to do tuning process. This property allows user to change the tuning step to more than one delay diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index ed23b9bedfdc..22d1e1f3f38b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -46,8 +46,12 @@ Optional properties: - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported +- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported - dsr: Value the card's (optional) Driver Stage Register (DSR) should be programmed with. Valid range: [0 .. 0xffff]. +- no-sdio: controller is limited to send sdio cmd during initialization +- no-sd: controller is limited to send sd cmd during initialization +- no-mmc: controller is limited to send mmc cmd during initialization *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt new file mode 100644 index 000000000000..78722d74cea8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt @@ -0,0 +1,37 @@ +APM X-Gene SoC MDIO node + +MDIO node is defined to describe on-chip MDIO controller. + +Required properties: + - compatible: Must be "apm,xgene-mdio-rgmii" or "apm,xgene-mdio-xfi" + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + - reg: Address and length of the register set + - clocks: Reference to the clock entry + +For the phys on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Example: + + mdio: mdio@17020000 { + compatible = "apm,xgene-mdio-rgmii"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x17020000 0x0 0xd100>; + clocks = <&menetclk 0>; + }; + + /* Board-specific peripheral configurations */ + &mdio { + menetphy: phy@3 { + reg = <0x3>; + }; + sgenet0phy: phy@4 { + reg = <0x4>; + }; + sgenet1phy: phy@5 { + reg = <0x5>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt new file mode 100644 index 000000000000..dfe287a5d6f2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt @@ -0,0 +1,59 @@ +Properties for an MDIO bus multiplexer found in Broadcom iProc based SoCs. + +This MDIO bus multiplexer defines buses that could be internal as well as +external to SoCs and could accept MDIO transaction compatible to C-22 or +C-45 Clause. When child bus is selected, one needs to select these two +properties as well to generate desired MDIO transaction on appropriate bus. + +Required properties in addition to the generic multiplexer properties: + +MDIO multiplexer node: +- compatible: brcm,mdio-mux-iproc. + +Every non-ethernet PHY requires a compatible so that it could be probed based +on this compatible string. + +Additional information regarding generic multiplexer properties can be found +at- Documentation/devicetree/bindings/net/mdio-mux.txt + + +for example: + mdio_mux_iproc: mdio-mux@6602023c { + compatible = "brcm,mdio-mux-iproc"; + reg = <0x6602023c 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + + mdio@7 { + reg = <0x7>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy1: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + mdio@10 { + reg = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + gphy0: eth-phy@10 { + reg = <0x10>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt new file mode 100644 index 000000000000..22a6f10bab05 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -0,0 +1,96 @@ +Renesas R-Car CAN FD controller Device Tree Bindings +---------------------------------------------------- + +Required properties: +- compatible: Must contain one or more of the following: + - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. + - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + +- reg: physical base address and size of the R-Car CAN FD register map. +- interrupts: interrupt specifier for the Global & Channel interrupts +- clocks: phandles and clock specifiers for 3 clock inputs. +- clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Required child nodes: +The controller supports two channels and each is represented as a child node. +The name of the child nodes are "channel0" and "channel1" respectively. Each +child node supports the "status" property only, which is used to +enable/disable the respective channel. + +Required properties for "renesas,r8a7795-canfd" compatible: +In R8A7795 SoC, canfd clock is a div6 clock and can be used by both CAN +and CAN FD controller at the same time. It needs to be scaled to maximum +frequency if any of these controllers use it. This is done using the +below properties. + +- assigned-clocks: phandle of canfd clock. +- assigned-clock-rates: maximum frequency of this clock. + +Optional property: +The controller can operate in either CAN FD only mode (default) or +Classical CAN only mode. The mode is global to both the channels. In order to +enable the later, define the following optional property. + - renesas,no-can-fd: puts the controller in Classical CAN only mode. + +Example +------- + +SoC common .dtsi file: + + canfd: can@e66c0000 { + compatible = "renesas,r8a7795-canfd", + "renesas,rcar-gen3-canfd"; + reg = <0 0xe66c0000 0 0x8000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 914>, + <&cpg CPG_CORE R8A7795_CLK_CANFD>, + <&can_clk>; + clock-names = "fck", "canfd", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&cpg>; + status = "disabled"; + + channel0 { + status = "disabled"; + }; + + channel1 { + status = "disabled"; + }; + }; + +Board specific .dts file: + +E.g. below enables Channel 1 alone in the board in Classical CAN only mode. + +&canfd { + pinctrl-0 = <&canfd1_pins>; + pinctrl-names = "default"; + renesas,no-can-fd; + status = "okay"; + + channel1 { + status = "okay"; + }; +}; + +E.g. below enables Channel 0 alone in the board using External clock +as fCAN clock. + +&canfd { + pinctrl-0 = <&canfd0_pins &can_clk_pins>; + pinctrl-names = "default"; + status = "okay"; + + channel0 { + status = "okay"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt index 7dbd158810d2..e3b8fe71762b 100644 --- a/Documentation/devicetree/bindings/net/cavium-pip.txt +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -37,6 +37,12 @@ Properties for PIP port which is a child the PIP interface: - phy-handle: Optional, see ethernet.txt file in the same directory. +- rx-delay: Delay value for RGMII receive clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + +- tx-delay: Delay value for RGMII transmit clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + Example: pip@11800a0000000 { diff --git a/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt new file mode 100644 index 000000000000..c070076bacb9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt @@ -0,0 +1,13 @@ +* Cirrus Logic CS8900/CS8920 Network Controller + +Required properties: +- compatible : Should be "cirrus,cs8900" or "cirrus,cs8920". +- reg : Address and length of the IO space. +- interrupts : Should contain the controller interrupt line. + +Examples: + eth0: eth@10000000 { + compatible = "cirrus,cs8900"; + reg = <0x10000000 0x400>; + interrupts = <10>; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 0ae06491b430..5ad439f30135 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -15,7 +15,6 @@ Required properties: - cpdma_channels : Specifies number of channels in CPDMA - ale_entries : Specifies No of entries ALE can hold - bd_ram_size : Specifies internal descriptor RAM size -- rx_descs : Specifies number of Rx descriptors - mac_control : Specifies Default MAC control register content for the specific platform - slaves : Specifies number for slaves diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 0369e25aabd2..621156ca4ffd 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -2,7 +2,10 @@ TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings --------------------------------------------------- Required properties: -- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" +- compatible : Should be "ti,davinci_mdio" + and "ti,keystone_mdio" for Keystone 2 SoCs + and "ti,cpsw-mdio" for am335x, am472x, am57xx/dra7, dm814x SoCs + and "ti,am4372-mdio" for am472x SoC - reg : physical base address and size of the davinci mdio registers map - bus_freq : Mdio Bus frequency diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt new file mode 100644 index 000000000000..d6c6e41648d4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -0,0 +1,97 @@ +Broadcom BCM53xx Ethernet switches +================================== + +Required properties: + +- compatible: For external switch chips, compatible string must be exactly one + of: "brcm,bcm5325" + "brcm,bcm53115" + "brcm,bcm53125" + "brcm,bcm53128" + "brcm,bcm5365" + "brcm,bcm5395" + "brcm,bcm5397" + "brcm,bcm5398" + + For the BCM5310x SoCs with an integrated switch, must be one of: + "brcm,bcm53010-srab" + "brcm,bcm53011-srab" + "brcm,bcm53012-srab" + "brcm,bcm53018-srab" + "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string + + For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of: + "brcm,bcm58522-srab" + "brcm,bcm58523-srab" + "brcm,bcm58525-srab" + "brcm,bcm58622-srab" + "brcm,bcm58623-srab" + "brcm,bcm58625-srab" + "brcm,bcm88312-srab" and the mandatory "brcm,nsp-srab string + + For the BCM63xx/33xx SoCs with an integrated switch, must be one of: + "brcm,bcm3384-switch" + "brcm,bcm6328-switch" + "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" + +See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +required and optional properties. + +Examples: + +Ethernet switch connected via MDIO to the host, CPU port wired to eth0: + + eth0: ethernet@10001000 { + compatible = "brcm,unimac"; + reg = <0x10001000 0x1000>; + + fixed-link { + speed = <1000>; + duplex-full; + }; + }; + + mdio0: mdio@10000000 { + compatible = "brcm,unimac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + switch0: ethernet-switch@30 { + compatible = "brcm,bcm53125"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + port0@0 { + reg = <0>; + label = "lan1"; + }; + + port1@1 { + reg = <1>; + label = "lan2"; + }; + + port5@5 { + reg = <5>; + label = "cable-modem"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + }; + + port8@8 { + reg = <8>; + label = "cpu"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + ethernet = <ð0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 9f4807f90c31..a4a570fb2494 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -1,5 +1,279 @@ -Marvell Distributed Switch Architecture Device Tree Bindings ------------------------------------------------------------- +Distributed Switch Architecture Device Tree Bindings +---------------------------------------------------- + +Two bindings exist, one of which has been deprecated due to +limitations. + +Current Binding +--------------- + +Switches are true Linux devices and can be probes by any means. Once +probed, they register to the DSA framework, passing a node +pointer. This node is expected to fulfil the following binding, and +may contain additional properties as required by the device it is +embedded within. + +Required properties: + +- ports : A container for child nodes representing switch ports. + +Optional properties: + +- dsa,member : A two element list indicates which DSA cluster, and position + within the cluster a switch takes. <0 0> is cluster 0, + switch 0. <0 1> is cluster 0, switch 1. <1 0> is cluster 1, + switch 0. A switch not part of any cluster (single device + hanging off a CPU port) must not specify this property + +The ports container has the following properties + +Required properties: + +- #address-cells : Must be 1 +- #size-cells : Must be 0 + +Each port children node must have the following mandatory properties: +- reg : Describes the port address in the switch +- label : Describes the label associated with this port, which + will become the netdev name. Special labels are + "cpu" to indicate a CPU port and "dsa" to + indicate an uplink/downlink port between switches in + the cluster. + +A port labelled "dsa" has the following mandatory property: + +- link : Should be a list of phandles to other switch's DSA + port. This port is used as the outgoing port + towards the phandle ports. The full routing + information must be given, not just the one hop + routes to neighbouring switches. + +A port labelled "cpu" has the following mandatory property: + +- ethernet : Should be a phandle to a valid Ethernet device node. + This host device is what the switch port is + connected to. + +Port child nodes may also contain the following optional standardised +properties, described in binding documents: + +- phy-handle : Phandle to a PHY on an MDIO bus. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +Example + +The following example shows three switches on three MDIO busses, +linked into one DSA cluster. + +&mdio1 { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch0@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + switch0port5: port@5 { + reg = <5>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port6 + &switch2port9>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&fec1>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; +}; + +&mdio2 { + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch1@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan3"; + phy-handle = <&switch1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-handle = <&switch1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan5"; + phy-handle = <&switch1phy2>; + }; + + switch1port5: port@5 { + reg = <5>; + label = "dsa"; + link = <&switch2port9>; + phy-mode = "rgmii-txid"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch1port6: port@6 { + reg = <6>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + }; + switch1phy1: switch1phy0@1 { + reg = <1>; + }; + switch1phy2: switch1phy0@2 { + reg = <2>; + }; + }; + }; +}; + +&mdio4 { + #address-cells = <1>; + #size-cells = <0>; + + switch2: switch2@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsa,member = <0 2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan6"; + }; + + port@1 { + reg = <1>; + label = "lan7"; + }; + + port@2 { + reg = <2>; + label = "lan8"; + }; + + port@3 { + reg = <3>; + label = "optical3"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 2 + GPIO_ACTIVE_HIGH>; + }; + }; + + port@4 { + reg = <4>; + label = "optical4"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 3 + GPIO_ACTIVE_HIGH>; + }; + }; + + switch2port9: port@9 { + reg = <9>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port5 + &switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +Deprecated Binding +------------------ + +The deprecated binding makes use of a platform device to represent the +switches. The switches themselves are not Linux devices, and make use +of an MDIO bus for management. Required properties: - compatible : Should be "marvell,dsa" @@ -43,7 +317,7 @@ Each port children node must have the following mandatory properties: Note that a port labelled "dsa" will imply checking for the uplink phandle described below. -Optionnal property: +Optional property: - link : Should be a list of phandles to another switch's DSA port. This property is only used when switches are being chained/cascaded together. This port is used as outgoing port diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt new file mode 100644 index 000000000000..23a39a309d17 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt @@ -0,0 +1,22 @@ +Hisilicon Fast Ethernet MDIO Controller interface + +Required properties: +- compatible: should be "hisilicon,hisi-femac-mdio". +- reg: address and length of the register set for the device. +- clocks: A phandle to the reference clock for this device. + +- PHY subnode: inherits from phy binding [1] +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: +mdio: mdio@10091100 { + compatible = "hisilicon,hisi-femac-mdio"; + reg = <0x10091100 0x10>; + clocks = <&crg HI3516CV300_MDIO_CLK>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@1 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac.txt b/Documentation/devicetree/bindings/net/hisilicon-femac.txt new file mode 100644 index 000000000000..d11af5ecace8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac.txt @@ -0,0 +1,39 @@ +Hisilicon Fast Ethernet MAC controller + +Required properties: +- compatible: should contain one of the following version strings: + * "hisilicon,hisi-femac-v1" + * "hisilicon,hisi-femac-v2" + and the soc string "hisilicon,hi3516cv300-femac". +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC core register base and size. + The second region is the global MAC control register. +- interrupts: should contain the MAC interrupt. +- clocks: A phandle to the MAC main clock. +- resets: should contain the phandle to the MAC reset signal(required) and + the PHY reset signal(optional). +- reset-names: should contain the reset signal name "mac"(required) + and "phy"(optional). +- mac-address: see ethernet.txt [1]. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + +Example: + hisi_femac: ethernet@10090000 { + compatible = "hisilicon,hi3516cv300-femac","hisilicon,hisi-femac-v2"; + reg = <0x10090000 0x1000>,<0x10091300 0x200>; + interrupts = <12>; + clocks = <&crg HI3518EV200_ETH_CLK>; + resets = <&crg 0xec 0>,<&crg 0xec 3>; + reset-names = "mac","phy"; + mac-address = [00 00 00 00 00 00]; + phy-mode = "mii"; + phy-handle = <&phy0>; + hisilicon,phy-reset-delays-us = <10000 20000 20000>; + }; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index b30ab6b5cbfa..04ba1dc34fd6 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -2,7 +2,7 @@ This document describes the device tree bindings associated with the keystone network coprocessor(NetCP) driver support. The network coprocessor (NetCP) is a hardware accelerator that processes -Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet +Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet switch sub-module to send and receive packets. NetCP also includes a packet accelerator (PA) module to perform packet classification operations such as header matching, and packet modification operations such as checksum diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt index 491f5bd55203..f58571f36570 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -5,11 +5,12 @@ numbered uniquely in a device dependent manner. The nodes for an MDIO bus multiplexer/switch will have one child node for each child bus. Required properties: -- mdio-parent-bus : phandle to the parent MDIO bus. - #address-cells = <1>; - #size-cells = <0>; Optional properties: +- mdio-parent-bus : phandle to the parent MDIO bus. + - Other properties specific to the multiplexer/switch hardware. Required properties for child nodes: diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt index 87496a8c64ab..8d157f0295a5 100644 --- a/Documentation/devicetree/bindings/net/micrel.txt +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -35,3 +35,13 @@ Optional properties: supported clocks: - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference input clock. Used to determine the XI input clock. + + - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode + + Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled + by the FXEN boot strapping pin. It can't be determined from the PHY + registers whether the PHY is in fiber mode, so this boolean device tree + property can be used to describe it. + + In fiber mode, auto-negotiation is disabled and the PHY can only work in + 100base-fx (full and half duplex) modes. diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt index 93eac7ce1446..cccd945fc45b 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -3,7 +3,8 @@ Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) The device node has following properties. Required properties: - - compatible: Can be one of "rockchip,rk3288-gmac", "rockchip,rk3368-gmac" + - compatible: Can be one of "rockchip,rk3228-gmac", "rockchip,rk3288-gmac", + "rockchip,rk3368-gmac" - reg: addresses and length of the register sets for the device. - interrupts: Should contain the GMAC interrupts. - interrupt-names: Should contain the interrupt names "macirq". diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 72d82d684342..2e68a3cd8513 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -17,9 +17,26 @@ Required properties: Optional properties: altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if DWMAC controller is connected emac splitter. +phy-mode: The phy mode the ethernet operates in +altr,sgmii-to-sgmii-converter: phandle to the TSE SGMII converter + +This device node has additional phandle dependency, the sgmii converter: + +Required properties: + - compatible : Should be altr,gmii-to-sgmii-2.0 + - reg-names : Should be "eth_tse_control_port" Example: +gmii_to_sgmii_converter: phy@0x100000240 { + compatible = "altr,gmii-to-sgmii-2.0"; + reg = <0x00000001 0x00000240 0x00000008>, + <0x00000001 0x00000200 0x00000040>; + reg-names = "eth_tse_control_port"; + clocks = <&sgmii_1_clk_0 &emac1 1 &sgmii_clk_125 &sgmii_clk_125>; + clock-names = "tse_pcs_ref_clk_clock_connection", "tse_rx_cdr_refclk"; +}; + gmac0: ethernet@ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; altr,sysmgr-syscon = <&sysmgr 0x60 0>; @@ -30,4 +47,6 @@ gmac0: ethernet@ff700000 { mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ clocks = <&emac_0_clk>; clock-names = "stmmaceth"; + phy-mode = "sgmii"; + altr,gmii-to-sgmii-converter = <&gmii_to_sgmii_converter>; }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 95816c5fc589..41b49e6075f5 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -47,6 +47,9 @@ Optional properties: supported by this device instance - snps,perfect-filter-entries: Number of perfect filter entries supported by this device instance +- snps,ps-speed: port selection speed that can be passed to the core when + PCS is supported. For example, this is used in case of SGMII + and MAC2MAC connection. - AXI BUS Mode parameters: below the list of all the parameters to program the AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt index 9180724e182c..8f9ced076fe1 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -1,19 +1,30 @@ -* Texas Instruments wl1271 wireless lan controller +* Texas Instruments wl12xx/wl18xx wireless lan controller -The wl1271 chip can be connected via SPI or via SDIO. This +The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This document describes the binding for the SPI connected chip. Required properties: -- compatible : Should be "ti,wl1271" +- compatible : Should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" - reg : Chip select address of device - spi-max-frequency : Maximum SPI clocking speed of device in Hz -- ref-clock-frequency : Reference clock frequency - interrupt-parent, interrupts : Should contain parameters for 1 interrupt line. Interrupt parameters: parent, line number, type. -- vwlan-supply : Point the node of the regulator that powers/enable the wl1271 chip +- vwlan-supply : Point the node of the regulator that powers/enable the + wl12xx/wl18xx chip Optional properties: +- ref-clock-frequency : Reference clock frequency (should be set for wl12xx) - clock-xtal : boolean, clock is generated from XTAL - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt @@ -21,16 +32,28 @@ Optional properties: Examples: +For wl12xx family: &spi1 { - wl1271@1 { + wlcore: wlcore@1 { compatible = "ti,wl1271"; - reg = <1>; spi-max-frequency = <48000000>; - clock-xtal; - ref-clock-frequency = <38400000>; interrupt-parent = <&gpio3>; interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; +}; + +For wl18xx family: +&spi0 { + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; }; }; diff --git a/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt new file mode 100644 index 000000000000..5b51007c6f24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt @@ -0,0 +1,27 @@ +* Broadcom NS2 PCIe PHY binding document + +Required bus properties: +- reg: MDIO Bus number for the MDIO interface +- #address-cells: must be 1 +- #size-cells: must be 0 + +Required PHY properties: +- compatible: should be "brcm,ns2-pcie-phy" +- reg: MDIO Phy ID for the MDIO interface +- #phy-cells: must be 0 + +This is a child bus node of "brcm,mdio-mux-iproc" node. + +Example: + +mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index d0231209d846..6ccce09d8bbf 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -5,6 +5,7 @@ Required properties: "brcm,bcm7425-sata-phy" "brcm,bcm7445-sata-phy" "brcm,iproc-ns2-sata-phy" + "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" - address-cells: should be 1 - size-cells: should be 0 @@ -22,7 +23,8 @@ Sub-nodes required properties: Sub-nodes optional properties: - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port - This property is not applicable for "brcm,iproc-ns2-sata-phy". + This property is not applicable for "brcm,iproc-ns2-sata-phy" and + "brcm,iproc-nsp-sata-phy". Example: sata-phy@f0458100 { diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt new file mode 100644 index 000000000000..c26478be391b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -0,0 +1,40 @@ +TI DA8xx/OMAP-L1xx/AM18xx USB PHY + +Required properties: + - compatible: must be "ti,da830-usb-phy". + - #phy-cells: must be 1. + +This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG +controllers on DA8xx SoCs. Consumers of this device should use index 0 for +the USB 2.0 phy device and index 1 for the USB 1.1 phy device. + +It also requires a "syscon" node with compatible = "ti,da830-cfgchip", "syscon" +to access the CFGCHIP2 register. + +Example: + + cfgchip: cfgchip@1417c { + compatible = "ti,da830-cfgchip", "syscon"; + reg = <0x1417c 0x14>; + }; + + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <1>; + }; + + usb20: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x200000 0x1000>; + interrupts = <58>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + }; + + usb11: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt index 555cb0f40690..e3ea55763b0a 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -7,6 +7,13 @@ Required properties: - reg: PHY register address offset and length in "general register files" +Optional clocks using the clock bindings (see ../clock/clock-bindings.txt), +specified by name: + - clock-names: Should contain "emmcclk". Although this is listed as optional + (because most boards can get basic functionality without having + access to it), it is strongly suggested. + - clocks: Should have a phandle to the card clock exported by the SDHCI driver. + Example: @@ -20,6 +27,8 @@ grf: syscon@ff770000 { emmcphy: phy@f780 { compatible = "rockchip,rk3399-emmc-phy"; reg = <0xf780 0x20>; + clocks = <&sdhci>; + clock-names = "emmcclk"; #phy-cells = <0>; }; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index 68498d560354..cc6be9680a6d 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -5,11 +5,13 @@ Required properties: "rockchip,rk3066a-usb-phy" "rockchip,rk3188-usb-phy" "rockchip,rk3288-usb-phy" - - rockchip,grf : phandle to the syscon managing the "general - register files" - #address-cells: should be 1 - #size-cells: should be 0 +Deprecated properties: + - rockchip,grf : phandle to the syscon managing the "general + register files" - phy should be a child of the GRF instead + Sub-nodes: Each PHY should be represented as a sub-node. @@ -28,14 +30,19 @@ Optional Properties: Example: -usbphy: phy { - compatible = "rockchip,rk3288-usb-phy"; - rockchip,grf = <&grf>; - #address-cells = <1>; - #size-cells = <0>; +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + #address-cells = <1>; + #size-cells = <0>; - usbphy0: usb-phy0 { - #phy-cells = <0>; - reg = <0x320>; + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt index e4277921f3e3..a73cbeb0f309 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt @@ -3,8 +3,22 @@ Broadcom iProc GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", - "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" + "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that + supports full-featured pinctrl and GPIO functions used in various iProc + based SoCs + + May contain an SoC-specific compatibility string to accommodate any + SoC-specific features + + "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or + "brcm,cygnus-crmu-gpio" for Cygnus SoCs + + "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support + disabled + + "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general + pinctrl support completely disabled in this IP block. In Stingray, a + different IP block is used to handle pinctrl related functions - reg: Define the base and range of the I/O address space that contains SoC diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt new file mode 100644 index 000000000000..603564e5fe6f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,nsp-pinmux.txt @@ -0,0 +1,79 @@ +Broadcom NSP (Northstar plus) IOMUX Controller + +The NSP IOMUX controller supports group based mux configuration. In +addition, certain pins can be muxed to GPIO function individually. + +Required properties: +- compatible: + Must be "brcm,nsp-pinmux" + +- reg: + Should contain the register physical address and length for each of + GPIO_CONTROL0, GP_AUX_SEL and IPROC_CONFIG IOMUX registers + +Properties in subnodes: +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinmux: pinmux@1803f1c0 { + compatible = "brcm,nsp-pinmux"; + reg = <0x1803f1c0 0x04>, + <0x18030028 0x04>, + <0x1803f408 0x04>; + + pinctrl-names = "default"; + pinctrl-0 = <&pwm &gpio_b &nand_sel>; + + pwm: pwm { + function = "pwm"; + groups = "pwm0_grp", "pwm1_grp"; + }; + + gpio_b: gpio_b { + function = "gpio_b"; + groups = "gpio_b_0_grp", "gpio_b_1_grp"; + }; + + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + }; + +List of supported functions and groups in Northstar Plus: + +"spi": "spi_grp" + +"i2c": "i2c_grp" + +"mdio": "mdio_grp" + +"pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" + +"gpio_b": "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp", "gpio_b_3_grp" + +"uart1": "uart1_grp" + +"uart2": "uart2_grp" + +"synce": "synce_grp" + +"sata_led_grps": "sata0_led_grp", "sata1_led_grp" + +"xtal_out": "xtal_out_grp" + +"sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +"switch_led": "switch_p05_led0_grp", "switch_p05_led1_grp" + +"nand": "nand_grp" + +"emmc": "emmc_grp" diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt new file mode 100644 index 000000000000..d6074321f730 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -0,0 +1,57 @@ +* Oxford Semiconductor OXNAS SoC Family Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +OXNAS 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configurations of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "oxsemi,ox810se-pinctrl" + - oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + +Example: + +pinctrl: pinctrl { + compatible = "oxsemi,ox810se-pinctrl"; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + pinctrl_uart2: pinctrl_uart2 { + uart2a { + pins = "gpio31"; + function = "fct3"; + }; + uart2b { + pins = "gpio32"; + function = "fct3"; + }; + }; +}; + +uart2: serial@900000 { + compatible = "ns16550a"; + reg = <0x900000 0x100000>; + clocks = <&sysclk>; + interrupts = <29>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + resets = <&reset 22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt new file mode 100644 index 000000000000..ad4fce3552bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt @@ -0,0 +1,127 @@ +Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7. + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + drive-push-pull, + drive-open-drain, + bias-pull-up, + bias-pull-down. + +Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in, + reference-out + +Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These +customised properties are required to configure FPS configuration parameters +of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more +detail of Flexible Power Sequence (FPS). + +- maxim,active-fps-source: FPS source for the GPIOs to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + GPIO is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + GPIO to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the GPIO get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the GPIO get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + + pinctrl-names = "default"; + pinctrl-0 = <&spmic_default>; + + spmic_default: pinmux@0 { + pin_gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + pin_gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + pin_gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt new file mode 100644 index 000000000000..1b52f01ddcb7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt @@ -0,0 +1,152 @@ +Qualcomm MDM9615 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MDM9615 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,mdm9615-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio87 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. + Valid values are: + gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart, + sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, + cdc_mclk + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,mdm9615-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + + gsbi8_uart: gsbi8-uart { + mux { + pins = "gpio34", "gpio35"; + function = "gsbi8"; + }; + + tx { + pins = "gpio34"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio35"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt index 77aa11790163..df9a838ec5f9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.txt @@ -52,7 +52,7 @@ Valid values for function are: gsbi2_spi_cs3_n, gsbi3, gsbi3_spi_cs1_n, gsbi3_spi_cs2_n, gsbi3_spi_cs3_n, gsbi4, gsbi5, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, gsbi11, gsbi12, hdmi, i2s, lcdc, mdp_vsync, mi2s, pcm, ps_hold, sdc1, sdc2, sdc5, tsif1, tsif2, usb_fs1, - usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, + usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs Example: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index e4d6a9d20f7d..453bd7c76d6b 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -49,6 +49,9 @@ Valid values for pins are: sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data Supports bias and drive-strength + hsic_data, hsic_strobe + Supports only mux + Valid values for function are: cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, @@ -70,7 +73,7 @@ Valid values for function are: cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, - ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio (Note that this is not yet the complete list of functions) diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index d74e631e10da..b484ba1af78c 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -9,6 +9,7 @@ of PMIC's from Qualcomm. Definition: Should contain one of: "qcom,pm8018-mpp", "qcom,pm8038-mpp", + "qcom,pm8058-mpp", "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 74e6ec0339d6..e4cf022c992e 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -72,7 +72,7 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For +bias-disable, bias-pull-up, bias-pull-down, drive-strength and power-source. For pins that have a configurable I/O voltage, the power-source value should be the nominal I/O voltage in millivolts. diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 7b4800cc251e..587bffb9cbc6 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -9,6 +9,7 @@ Pin controller node: Required properies: - compatible: value should be one of the following: (a) "st,stm32f429-pinctrl" + (b) "st,stm32f746-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to diff --git a/Documentation/devicetree/bindings/power/max8903-charger.txt b/Documentation/devicetree/bindings/power/max8903-charger.txt new file mode 100644 index 000000000000..f0f4e12b076e --- /dev/null +++ b/Documentation/devicetree/bindings/power/max8903-charger.txt @@ -0,0 +1,25 @@ +Maxim Semiconductor MAX8903 Battery Charger bindings + +Required properties: +- compatible: "maxim,max8903" for MAX8903 Battery Charger +- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided +- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided + +Optional properties: +- cen-gpios: Charge enable pin (active low, output) +- chg-gpios: Charger status pin (active low, input) +- flt-gpios: Fault pin (active low, output) +- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) +- usus-gpios: USB suspend pin (active high, output) + + +Example: + + max8903-charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm21664-resetmgr.txt b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt index 93f31ca1ef4b..93f31ca1ef4b 100644 --- a/Documentation/devicetree/bindings/reset/brcm,bcm21664-resetmgr.txt +++ b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt diff --git a/Documentation/devicetree/bindings/power/reset/reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt new file mode 100644 index 000000000000..de34f27d509e --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt @@ -0,0 +1,25 @@ +Generic reboot mode core map driver + +This driver get reboot mode arguments and call the write +interface to store the magic value in special register +or ram. Then the bootloader can read it and take different +action according to the argument stored. + +All mode properties are vendor specific, it is a indication to tell +the bootloader what to do when the system reboots, and should be named +as mode-xxx = <magic> (xxx is mode name, magic should be a none-zero value). + +For example modes common on Android platform: +- mode-normal: Normal reboot mode, system reboot with command "reboot". +- mode-recovery: Android Recovery mode, it is a mode to format the device or update a new image. +- mode-bootloader: Android fastboot mode, it's a mode to re-flash partitions on the Android based device. +- mode-loader: A bootloader mode, it's a mode used to download image on Rockchip platform, + usually used in development. + +Example: + reboot-mode { + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + } diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt new file mode 100644 index 000000000000..f7ce1d8af04a --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt @@ -0,0 +1,35 @@ +SYSCON reboot mode driver + +This driver gets reboot mode magic value form reboot-mode driver +and stores it in a SYSCON mapped register. Then the bootloader +can read it and take different action according to the magic +value stored. + +This DT node should be represented as a sub-node of a "syscon", "simple-mfd" +node. + +Required properties: +- compatible: should be "syscon-reboot-mode" +- offset: offset in the register map for the storage register (in bytes) + +Optional property: +- mask: bits mask of the bits in the register to store the reboot mode magic value, + default set to 0xffffffff if missing. + +The rest of the properties should follow the generic reboot-mode description +found in reboot-mode.txt + +Example: + pmu: pmu@20004000 { + compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd"; + reg = <0x20004000 0x100>; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x40>; + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + }; + }; diff --git a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt index 862f4a49dc49..f1d7beec45bf 100644 --- a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt +++ b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt @@ -1,7 +1,8 @@ AXP20x USB power supply Required Properties: --compatible: "x-powers,axp202-usb-power-supply" +-compatible: One of: "x-powers,axp202-usb-power-supply" + "x-powers,axp221-usb-power-supply" This node is a subnode of the axp20x PMIC. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt deleted file mode 100644 index 29b28b8f9a89..000000000000 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt +++ /dev/null @@ -1,43 +0,0 @@ -* Network - -Currently defined compatibles: -- fsl,cpm1-scc-enet -- fsl,cpm2-scc-enet -- fsl,cpm1-fec-enet -- fsl,cpm2-fcc-enet (third resource is GFEMR) -- fsl,qe-enet - -Example: - - ethernet@11300 { - compatible = "fsl,mpc8272-fcc-enet", - "fsl,cpm2-fcc-enet"; - reg = <11300 20 8400 100 11390 1>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <20 8>; - interrupt-parent = <&PIC>; - phy-handle = <&PHY0>; - fsl,cpm-command = <12000300>; - }; - -* MDIO - -Currently defined compatibles: -fsl,pq1-fec-mdio (reg is same as first resource of FEC device) -fsl,cpm2-mdio-bitbang (reg is port C registers) - -Properties for fsl,cpm2-mdio-bitbang: -fsl,mdio-pin : pin of port C controlling mdio data -fsl,mdc-pin : pin of port C controlling mdio clock - -Example: - mdio@10d40 { - compatible = "fsl,mpc8272ads-mdio-bitbang", - "fsl,mpc8272-mdio-bitbang", - "fsl,cpm2-mdio-bitbang"; - reg = <10d40 14>; - #address-cells = <1>; - #size-cells = <0>; - fsl,mdio-pin = <12>; - fsl,mdc-pin = <13>; - }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt index 55c2c03fc81e..df873d1f3b7c 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt @@ -35,7 +35,7 @@ PROPERTIES Definition: Specifies the index of the FMan unit. The cell-index value may be used by the SoC, to identify the - FMan unit in the SoC memory map. In the table bellow, + FMan unit in the SoC memory map. In the table below, there's a description of the cell-index use in each SoC: - P1023: @@ -247,7 +247,7 @@ PROPERTIES The cell-index value may be used by the FMan or the SoC, to identify the MAC unit in the FMan (or SoC) memory map. - In the tables bellow there's a description of the cell-index + In the tables below there's a description of the cell-index use, there are two tables, one describes the use of cell-index by the FMan, the second describes the use by the SoC: diff --git a/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt b/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt new file mode 100644 index 000000000000..dffb79108b61 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/opal/oppanel-opal.txt @@ -0,0 +1,14 @@ +IBM OPAL Operator Panel Binding +------------------------------- + +Required properties: +- compatible : Should be "ibm,opal-oppanel". +- #lines : Number of lines on the operator panel e.g. <0x2>. +- #length : Number of characters per line of the operator panel e.g. <0x10>. + +Example: + oppanel { + compatible = "ibm,opal-oppanel"; + #lines = <0x2>; + #length = <0x10>; + }; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index 0127be360fe8..873096be0278 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -14,7 +14,7 @@ architectures that typically run big-endian operating systems be marked that way in the devicetree. On SoCs that can be operated in both big-endian and little-endian -modes, with a single hardware switch controlling both the endianess +modes, with a single hardware switch controlling both the endianness of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS chips), "native-endian" is used to allow using the same device tree blob in both cases. diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index 7aa9b1fa6b21..58065ca9e3b4 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -1,4 +1,4 @@ -* Dialog Semiconductor DA9210 Voltage Regulator +* Dialog Semiconductor DA9210 Multi-phase 12A DCDC BUCK Converter Required properties: @@ -18,8 +18,12 @@ Example: compatible = "dlg,da9210"; reg = <0x68>; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1000000>; + interrupt-parent = <...>; + interrupts = <...>; + + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <1600000>; + regulator-max-microamp = <4600000>; regulator-boot-on; - regulator-always-on; }; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index c620493e8dbe..0f2a6f8fcafd 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,7 +1,8 @@ -* Dialog Semiconductor DA9211/DA9213/DA9215 Voltage Regulator +* Dialog Semiconductor DA9211/DA9212/DA9213/DA9214/DA9215 Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9213" or "dlg,da9215" +- compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" + or "dlg,da9214" or "dlg,da9215" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -30,6 +31,25 @@ Example 1) DA9211 regulator-max-microamp = <5000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 2) DA9212 + + pmic: da9212@68 { + compatible = "dlg,da9212"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -41,7 +61,7 @@ Example 1) DA9211 }; }; -Example 2) DA9213 +Example 3) DA9213 pmic: da9213@68 { compatible = "dlg,da9213"; reg = <0x68>; @@ -56,6 +76,24 @@ Example 2) DA9213 regulator-max-microamp = <6000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 4) DA9214 + pmic: da9214@68 { + compatible = "dlg,da9214"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -67,8 +105,7 @@ Example 2) DA9213 }; }; - -Example 3) DA9215 +Example 5) DA9215 pmic: da9215@68 { compatible = "dlg,da9215"; reg = <0x68>; diff --git a/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt new file mode 100644 index 000000000000..c35d878b0960 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt @@ -0,0 +1,237 @@ +Mediatek MT6323 Regulator Driver + +All voltage regulators are defined as subnodes of the regulators node. A list +of regulators provided by this controller are defined as subnodes of the +PMIC's node. Each regulator is named according to its regulator type, +buck_<name> and ldo_<name>. The definition for each of these nodes is defined +using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vproc, buck_vsys, buck_vpa +LDO: + ldo_vtcxo, ldo_vcn28, ldo_vcn33_bt, ldo_vcn33_wifi, ldo_va, ldo_vcama, + ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, ldo_vemc3v3, ldo_vgp1, ldo_vgp2, + ldo_vgp3, ldo_vcn18, ldo_vsim1, ldo_vsim2, ldo_vrtc, ldo_vcamaf, ldo_vibr, + ldo_vrf18, ldo_vm, ldo_vio18, ldo_vcamd, ldo_vcamio + +Example: + + pmic: mt6323 { + mt6323regulator: regulators { + mt6323_vproc_reg: buck_vproc{ + regulator-name = "vproc"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vsys_reg: buck_vsys{ + regulator-name = "vsys"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2987500>; + regulator-ramp-delay = <25000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vpa_reg: buck_vpa{ + regulator-name = "vpa"; + regulator-min-microvolt = < 500000>; + regulator-max-microvolt = <3650000>; + }; + + mt6323_vtcxo_reg: ldo_vtcxo{ + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcn28_reg: ldo_vcn28{ + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_bt_reg: ldo_vcn33_bt{ + regulator-name = "vcn33_bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_wifi_reg: ldo_vcn33_wifi{ + regulator-name = "vcn33_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_va_reg: ldo_va{ + regulator-name = "va"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcama_reg: ldo_vcama{ + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vio28_reg: ldo_vio28{ + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vusb_reg: ldo_vusb{ + regulator-name = "vusb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + regulator-boot-on; + }; + + mt6323_vmc_reg: ldo_vmc{ + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vmch_reg: ldo_vmch{ + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vemc3v3_reg: ldo_vemc3v3{ + regulator-name = "vemc3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vgp1_reg: ldo_vgp1{ + regulator-name = "vgp1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp2_reg: ldo_vgp2{ + regulator-name = "vgp2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp3_reg: ldo_vgp3{ + regulator-name = "vgp3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcn18_reg: ldo_vcn18{ + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim1_reg: ldo_vsim1{ + regulator-name = "vsim1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim2_reg: ldo_vsim2{ + regulator-name = "vsim2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vrtc_reg: ldo_vrtc{ + regulator-name = "vrtc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamaf_reg: ldo_vcamaf{ + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vibr_reg: ldo_vibr{ + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + }; + + mt6323_vrf18_reg: ldo_vrf18{ + regulator-name = "vrf18"; + regulator-min-microvolt = <1825000>; + regulator-max-microvolt = <1825000>; + regulator-enable-ramp-delay = <187>; + }; + + mt6323_vm_reg: ldo_vm{ + regulator-name = "vm"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vio18_reg: ldo_vio18{ + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamd_reg: ldo_vcamd{ + regulator-name = "vcamd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcamio_reg: ldo_vcamio{ + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ed936f0f34f2..dd6f59cf1455 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -38,13 +38,18 @@ NB: To be clear, if voltage-table is provided, then the device will be used in Voltage Table Mode. If no voltage-table is provided, then the device will be used in Continuous Voltage Mode. +Optional properties: +-------------------- +- enable-gpios: GPIO to use to enable/disable the regulator + Any property defined as part of the core regulator binding can also be used. (See: ../regulator/regulator.txt) -Continuous Voltage Example: +Continuous Voltage With Enable GPIO Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; regulator-min-microvolt = <1016000>; regulator-max-microvolt = <1114000>; regulator-name = "vdd_logic"; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 46c6f3ed1a1c..0fa3b0fac129 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -113,9 +113,9 @@ pm8916: l14, l15, l16, l17, l18 pm8941: - s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, - l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, - mvs1, mvs2 + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, + 5vs1, 5vs2 pm8994: s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt new file mode 100644 index 000000000000..57cb49ec55ca --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -0,0 +1,137 @@ +Qualcomm Hexagon Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm Hexagon core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,q6v5-pil" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the qdsp6 and + rmb register blocks + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: must be "q6dsp" and "rmb" + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog, fatal IRQs ready, handover and + stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + +- clocks: + Usage: required + Value type: <phandle> + Definition: reference to the iface, bus and mem clocks to be held on + behalf of the booting of the Hexagon core + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "iface", "bus", "mem" + +- resets: + Usage: required + Value type: <phandle> + Definition: reference to the reset-controller for the modem sub-system + +- reset-names: + Usage: required + Value type: <stringlist> + Definition: must be "mss_restart" + +- cx-supply: +- mss-supply: +- mx-supply: +- pll-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the Hexagon core + +- qcom,smem-states: + Usage: required + Value type: <phandle> + Definition: reference to the smem state for requesting the Hexagon to + shut down + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must be "stop" + +- qcom,halt-regs: + Usage: required + Value type: <prop-encoded-array> + Definition: a phandle reference to a syscon representing TCSR followed + by the three offsets within syscon for q6, modem and nc + halt registers. + += SUBNODES: +The Hexagon node must contain two subnodes, named "mba" and "mpss" representing +the memory regions used by the Hexagon firmware. Each sub-node must contain: + +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the region + += EXAMPLE +The following example describes the resources needed to boot control the +Hexagon, as it is found on MSM8974 boards. + + modem-rproc@fc880000 { + compatible = "qcom,q6v5-pil"; + reg = <0xfc880000 0x100>, + <0xfc820000 0x020>; + reg-names = "qdsp6", "rmb"; + + interrupts-extended = <&intc 0 24 1>, + <&modem_smp2p_in 0 0>, + <&modem_smp2p_in 1 0>, + <&modem_smp2p_in 2 0>, + <&modem_smp2p_in 3 0>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, + <&gcc GCC_MSS_CFG_AHB_CLK>, + <&gcc GCC_BOOT_ROM_AHB_CLK>; + clock-names = "iface", "bus", "mem"; + + qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>; + + resets = <&gcc GCC_MSS_RESTART>; + reset-names = "mss_restart"; + + cx-supply = <&pm8841_s2>; + mss-supply = <&pm8841_s3>; + mx-supply = <&pm8841_s1>; + pll-supply = <&pm8941_l12>; + + qcom,smem-states = <&modem_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + mba { + memory-region = <&mba_region>; + }; + + mpss { + memory-region = <&mpss_region>; + }; + }; diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt index 07ccdaa68324..26542690b578 100644 --- a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt @@ -2,7 +2,8 @@ BCM2835 Random number generator Required properties: -- compatible : should be "brcm,bcm2835-rng" +- compatible : should be "brcm,bcm2835-rng" or "brcm,bcm-nsp-rng" or + "brcm,bcm5301x-rng" - reg : Specifies base physical address and size of the registers. Example: @@ -11,3 +12,8 @@ rng { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; }; + +rng@18033000 { + compatible = "brcm,bcm-nsp-rng"; + reg = <0x18033000 0x14>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-opal.txt b/Documentation/devicetree/bindings/rtc/rtc-opal.txt index a1734e5cb75b..2340938cd0f5 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-opal.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-opal.txt @@ -2,7 +2,7 @@ IBM OPAL real-time clock ------------------------ Required properties: -- comapatible: Should be "ibm,opal-rtc" +- compatible: Should be "ibm,opal-rtc" Optional properties: - wakeup-source: Decides if the wakeup is supported or not diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt new file mode 100644 index 000000000000..85741cd468cc --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt @@ -0,0 +1,24 @@ +Required properties: +- compatible: should be one of the following + "st,st33htpm-spi" + "infineon,slb9670" + "tcg,tpm_tis-spi" +- spi-max-frequency: Maximum SPI frequency (depends on TPMs). + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with TPM_TIS on SPI4): + +&mcspi4 { + + status = "okay"; + + tpm_tis@0 { + + compatible = "tcg,tpm_tis-spi"; + + spi-max-frequency = <10000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 936ab5b87324..f5561ac7e17e 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,6 +42,9 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. It will use specified GPIO instead of the peripheral + function pin for the UART feature. If unsure, don't specify this property. Note: * fsl,ns16550: @@ -63,3 +66,19 @@ Example: interrupts = <10>; reg-shift = <2>; }; + +Example for OMAP UART using GPIO-based modem control signals: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index 182777fac9a2..d5f73b8f614f 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -28,10 +28,10 @@ Optional properties: - dma-names: Should contain "tx" for transmit and "rx" for receive channels - qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be used with TX DMA channel. Required when using DMA for transmission - with UARTDM v1.3 and bellow. + with UARTDM v1.3 and below. - qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be used with RX DMA channel. Required when using DMA for reception - with UARTDM v1.3 and bellow. + with UARTDM v1.3 and below. Note: Aliases may be defined to ensure the correct ordering of the UARTs. The alias serialN will result in the UART being assigned port N. If any diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 528c3b90f23c..1e4000d83aee 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -31,6 +31,8 @@ Required properties: - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. + - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. + - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, @@ -76,6 +78,10 @@ Optional properties: - dmas: Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. - dma-names: Must contain a list of two DMA names, "tx" and "rx". + - {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the + generic serial DT bindings in serial.txt. + - uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow + control, cfr. the generic serial DT bindings in serial.txt. Example: aliases { diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm.txt index 160c752484b4..160c752484b4 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/brg.txt index 4c7d45eaf025..4c7d45eaf025 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/brg.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/i2c.txt index 87bc6048667e..87bc6048667e 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/i2c.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/pic.txt index 8e3ee1681618..8e3ee1681618 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/pic.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/usb.txt index 74bfda4bb824..74bfda4bb824 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/usb.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/gpio.txt index 349f79fd7076..349f79fd7076 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/gpio.txt diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt new file mode 100644 index 000000000000..03c741602c6d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt @@ -0,0 +1,124 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; + +* HDLC + +Currently defined compatibles: +- fsl,ucc-hdlc + +Properties for fsl,ucc-hdlc: +- rx-clock-name +- tx-clock-name + Usage: required + Value type: <string> + Definition : Must be "brg1"-"brg16" for internal clock source, + Must be "clk1"-"clk24" for external clock source. + +- fsl,tdm-interface + Usage: optional + Value type: <empty> + Definition : Specify that hdlc is based on tdm-interface + +The property below is dependent on fsl,tdm-interface: +- fsl,rx-sync-clock + Usage: required + Value type: <string> + Definition : Must be "none", "rsync_pin", "brg9-11" and "brg13-15". + +- fsl,tx-sync-clock + Usage: required + Value type: <string> + Definition : Must be "none", "tsync_pin", "brg9-11" and "brg13-15". + +- fsl,tdm-framer-type + Usage: required for tdm interface + Value type: <string> + Definition : "e1" or "t1".Now e1 and t1 are used, other framer types + are not supported. + +- fsl,tdm-id + Usage: required for tdm interface + Value type: <u32> + Definition : number of TDM ID + +- fsl,tx-timeslot-mask +- fsl,rx-timeslot-mask + Usage: required for tdm interface + Value type: <u32> + Definition : time slot mask for TDM operation. Indicates which time + slots used for transmitting and receiving. + +- fsl,siram-entry-id + Usage: required for tdm interface + Value type: <u32> + Definition : Must be 0,2,4...64. the number of TDM entry. + +- fsl,tdm-internal-loopback + usage: optional for tdm interface + value type: <empty> + Definition : Internal loopback connecting on TDM layer. + +Example for tdm interface: + + ucc@2000 { + compatible = "fsl,ucc-hdlc"; + rx-clock-name = "clk8"; + tx-clock-name = "clk9"; + fsl,rx-sync-clock = "rsync_pin"; + fsl,tx-sync-clock = "tsync_pin"; + fsl,tx-timeslot-mask = <0xfffffffe>; + fsl,rx-timeslot-mask = <0xfffffffe>; + fsl,tdm-framer-type = "e1"; + fsl,tdm-id = <0>; + fsl,siram-entry-id = <0>; + fsl,tdm-interface; + }; + +Example for hdlc without tdm interface: + + ucc@2000 { + compatible = "fsl,ucc-hdlc"; + rx-clock-name = "brg1"; + tx-clock-name = "brg1"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt index 4f8930263dd9..d7afaff5faff 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt @@ -69,6 +69,58 @@ Example: }; }; +* Interrupt Controller (IC) + +Required properties: +- compatible : should be "fsl,qe-ic". +- reg : Address range of IC register set. +- interrupts : interrupts generated by the device. +- interrupt-controller : this device is a interrupt controller. + +Example: + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + interrupts = <95 2 0 0 94 2 0 0>; + }; + +* Serial Interface Block (SI) + +The SI manages the routing of eight TDM lines to the QE block serial drivers +, the MCC and the UCCs, for receive and transmit. + +Required properties: +- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain + "fsl,t1040-qe-si". +- reg : Address range of SI register set. + +Example: + + si1: si@700 { + compatible = "fsl,t1040-qe-si"; + reg = <0x700 0x80>; + }; + +* Serial Interface Block RAM(SIRAM) + +store the routing entries of SI + +Required properties: +- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain + "fsl,t1040-qe-siram". +- reg : Address range of SI RAM. + +Example: + + siram1: siram@1000 { + compatible = "fsl,t1040-qe-siram"; + reg = <0x1000 0x800>; + }; + * QE Firmware Node This node defines a firmware binary that is embedded in the device tree, for diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/firmware.txt index 249db3a15d15..249db3a15d15 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/firmware.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt index 60984260207b..60984260207b 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/par_io.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/pincfg.txt index ec6ee2e864a2..ec6ee2e864a2 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/pincfg.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ucc.txt index e47734bee3f0..e47734bee3f0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ucc.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/usb.txt index 9ccd5f30405b..9ccd5f30405b 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/usb.txt diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/serial.txt index 2ea76d9d137c..2ea76d9d137c 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/serial.txt diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt new file mode 100644 index 000000000000..8823c86c8085 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/uqe_serial.txt @@ -0,0 +1,17 @@ +* Serial + +Required Properties: +compatible : must be "fsl,<chip>-ucc-uart". For t1040, must be +"fsl,t1040-ucc-uart". +port-number : port number of UCC-UART +tx/rx-clock-name : should be "brg1"-"brg16" for internal clock source, + should be "clk1"-"clk28" for external clock source. + +Example: + + ucc_serial: ucc@2200 { + compatible = "fsl,t1040-ucc-uart"; + port-number = <0>; + rx-clock-name = "brg2"; + tx-clock-name = "brg2"; + }; diff --git a/Documentation/devicetree/bindings/sound/adi,adau17x1.txt b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt index 8dbce0e18dda..1447dec28125 100644 --- a/Documentation/devicetree/bindings/sound/adi,adau17x1.txt +++ b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt @@ -13,6 +13,11 @@ Required properties: - reg: The i2c address. Value depends on the state of ADDR0 and ADDR1, as wired in hardware. +Optional properties: + - clock-names: If provided must be "mclk". + - clocks: phandle + clock-specifiers for the clock that provides + the audio master clock for the device. + Examples: #include <dt-bindings/sound/adau17x1.h> @@ -20,5 +25,8 @@ Examples: adau1361@38 { compatible = "adi,adau1761"; reg = <0x38>; + + clock-names = "mclk"; + clocks = <&audio_clock>; }; }; diff --git a/Documentation/devicetree/bindings/sound/adi,adau7002.txt b/Documentation/devicetree/bindings/sound/adi,adau7002.txt new file mode 100644 index 000000000000..f144ee1abf85 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau7002.txt @@ -0,0 +1,19 @@ +Analog Devices ADAU7002 Stereo PDM-to-I2S/TDM Converter + +Required properties: + + - compatible: Must be "adi,adau7002" + +Optional properties: + + - IOVDD-supply: Phandle and specifier for the power supply providing the IOVDD + supply as covered in Documentation/devicetree/bindings/regulator/regulator.txt + + If this property is not present it is assumed that the supply pin is + hardwired to always on. + +Example: + adau7002: pdm-to-i2s { + compatible = "adi,adau7002"; + IOVDD-supply = <&supply>; + }; diff --git a/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt new file mode 100644 index 000000000000..b139e66d2a11 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt @@ -0,0 +1,67 @@ +BROADCOM Cygnus Audio I2S/TDM/SPDIF controller + +Required properties: + - compatible : "brcm,cygnus-audio" + - #address-cells: 32bit valued, 1 cell. + - #size-cells: 32bit valued, 0 cell. + - reg : Should contain audio registers location and length + - reg-names: names of the registers listed in "reg" property + Valid names are "aud" and "i2s_in". "aud" contains a + set of DMA, I2S_OUT and SPDIF registers. "i2s_in" contains + a set of I2S_IN registers. + - clocks: PLL and leaf clocks used by audio ports + - assigned-clocks: PLL and leaf clocks + - assigned-clock-parents: parent clocks of the assigned clocks + (usually the PLL) + - assigned-clock-rates: List of clock frequencies of the + assigned clocks + - clock-names: names of 3 leaf clocks used by audio ports + Valid names are "ch0_audio", "ch1_audio", "ch2_audio" + - interrupts: audio DMA interrupt number + +SSP Subnode properties: +- reg: The index of ssp port interface to use + Valid value are 0, 1, 2, or 3 (for spdif) + +Example: + cygnus_audio: audio@180ae000 { + compatible = "brcm,cygnus-audio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x180ae000 0xafd>, <0x180aec00 0x1f8>; + reg-names = "aud", "i2s_in"; + clocks = <&audiopll BCM_CYGNUS_AUDIOPLL_CH0>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH1>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH2>; + assigned-clocks = <&audiopll BCM_CYGNUS_AUDIOPLL>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH0>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH1>, + <&audiopll BCM_CYGNUS_AUDIOPLL_CH2>; + assigned-clock-parents = <&audiopll BCM_CYGNUS_AUDIOPLL>; + assigned-clock-rates = <1769470191>, + <0>, + <0>, + <0>; + clock-names = "ch0_audio", "ch1_audio", "ch2_audio"; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + + ssp0: ssp_port@0 { + reg = <0>; + status = "okay"; + }; + + ssp1: ssp_port@1 { + reg = <1>; + status = "disabled"; + }; + + ssp2: ssp_port@2 { + reg = <2>; + status = "disabled"; + }; + + spdif: spdif_port@3 { + reg = <3>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/bt-sco.txt b/Documentation/devicetree/bindings/sound/bt-sco.txt index 29b8e5d40203..641edf75e184 100644 --- a/Documentation/devicetree/bindings/sound/bt-sco.txt +++ b/Documentation/devicetree/bindings/sound/bt-sco.txt @@ -4,7 +4,7 @@ This device support generic Bluetooth SCO link. Required properties: - - compatible : "delta,dfbmcs320" + - compatible : "delta,dfbmcs320" or "linux,bt-sco" Example: diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt new file mode 100644 index 000000000000..acfb47525b49 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l33.txt @@ -0,0 +1,126 @@ +CS35L33 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l33" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : gpio used to reset the amplifier + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L33 are delivered to. + - interrupts : IRQ line info CS35L33. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is + 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with + a value of 1 and will increase at a step size of 100mV until a maximum of + 8000mV. + + - cirrus,ramp-rate : On power up, it affects the time from when the power + up sequence begins to the time the audio reaches a full-scale output. + On power down, it affects the time from when the power-down sequence + begins to when the amplifier disables the PWM outputs. If this property + is not set then soft ramping will be disabled and ramp time would be + 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms, + 60ms,100ms,175ms respectively for 48KHz sample rate. + + - cirrus,boost-ipk : The maximum current allowed for the boost converter. + The range starts at 1850000uA and goes to a maximum of 3600000uA + with a step size of 15625uA. The default is 2500000uA. + + - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON + ADC data word. This property can be set as a value of 0 for bits 15 down + to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8. + + +Optional H/G Algorithm sub-node: + +The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable +the internal H/G Algorithm. + + - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that + controls the amplifier supplies. + +Optional properties for the "cirrus,hg-algo" sub-node: + + - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in + LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory + depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles. + + cirrus,release-rate : The number of consecutive LRCLK periods before + allowing release condition tracking updates. The number of LRCLK periods + start at 3 to a maximum of 255. + + - cirrus,ldo-thld : Configures the signal threshold at which the PWM output + stage enters LDO operation. Starts as a default value of 50mV for a value + of 1 and increases with a step size of 50mV to a maximum of 750mV (value of + 0xF). + + - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G + algorithm uses the max detection path. If not present, the LDO + detection path is used. + + - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G + algorithm switches to the LDO voltage. This property can be set to values + from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms. + The default is 100ms. + + - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg + automatic updating is enabled. + + - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's + reference to the VP voltage for when to start generating a boosted VBST. + The reference voltage starts at 3000mV with a value of 0x3 and is increased + by 100mV per step to a maximum of 5500mV. + + - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is + allowed to increase to a higher voltage when using VPhg automatic + tracking. This property can be set to values from 0 to 3 with rates of 128 + periods, 2048 periods, 32768 periods, and 524288 periods. + The default is 32768 periods. + + - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking + using VPMON. This property can be set to values from 0 to 6 starting at + 1800mV with a step size of 50mV up to a maximum value of 1750mV. + Default is 1800mV. + +Example: + +cs35l33: cs35l33@40 { + compatible = "cirrus,cs35l33"; + reg = <0x40>; + + VA-supply = <&ldo5_reg>; + VP-supply = <&ldo5_reg>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&cs47l91 34 0>; + + cirrus,ramp-rate = <0x0>; + cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */ + cirrus,boost-ipk = <0xE0>; /* 3600mA */ + cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */ + + cirrus,hg-algo { + cirrus,mem-depth = <0x3>; + cirrus,release-rate = <0x3>; + cirrus,ldo-thld = <0x1>; + cirrus,ldo-path-disable = <0x0>; + cirrus,ldo-entry-delay=<0x4>; + cirrus,vp-hg-auto; + cirrus,vp-hg=<0xF>; + cirrus,vp-hg-rate=<0x2>; + cirrus,vp-hg-va=<0x0>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs53l30.txt b/Documentation/devicetree/bindings/sound/cs53l30.txt new file mode 100644 index 000000000000..4dbfb8274cd9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs53l30.txt @@ -0,0 +1,44 @@ +CS53L30 audio CODEC + +Required properties: + + - compatible : "cirrus,cs53l30" + + - reg : the I2C address of the device + + - VA-supply, VP-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. + + - mute-gpios : a GPIO spec for the MUTE pin. The active state can be either + GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW, which would be handled + by the driver automatically. + + - cirrus,micbias-lvl : Set the output voltage level on the MICBIAS Pin. + 0 = Hi-Z + 1 = 1.80 V + 2 = 2.75 V + + - cirrus,use-sdout2 : This is a boolean property. If present, it indicates + the hardware design connects both SDOUT1 and SDOUT2 + pins to output data. Otherwise, it indicates that + only SDOUT1 is connected for data output. + * CS53l30 supports 4-channel data output in the same + * frame using two different ways: + * 1) Normal I2S mode on two data pins -- each SDOUT + * carries 2-channel data in the same time. + * 2) TDM mode on one signle data pin -- SDOUT1 carries + * 4-channel data per frame. + +Example: + +codec: cs53l30@48 { + compatible = "cirrus,cs53l30"; + reg = <0x48>; + reset-gpios = <&gpio 54 0>; + VA-supply = <&cs53l30_va>; + VP-supply = <&cs53l30_vp>; +}; diff --git a/Documentation/devicetree/bindings/sound/designware-i2s.txt b/Documentation/devicetree/bindings/sound/designware-i2s.txt index 7bb54247f8e8..6a536d570e29 100644 --- a/Documentation/devicetree/bindings/sound/designware-i2s.txt +++ b/Documentation/devicetree/bindings/sound/designware-i2s.txt @@ -12,6 +12,10 @@ Required properties: one for receive. - dma-names : "tx" for the transmit channel, "rx" for the receive channel. +Optional properties: + - interrupts: The interrupt line number for the I2S controller. Add this + parameter if the I2S controller that you are using does not support DMA. + For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties please check: * resource-names.txt diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt index ceaef5126989..f749e2744824 100644 --- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -58,7 +58,7 @@ Required properties: * DMIC (stands for Digital Microphone Jack) Note: The "Mic Jack" and "AMIC" are redundant while - coexsiting in order to support the old bindings + coexisting in order to support the old bindings of wm8962 and sgtl5000. Optional properties: diff --git a/Documentation/devicetree/bindings/sound/max98504.txt b/Documentation/devicetree/bindings/sound/max98504.txt new file mode 100644 index 000000000000..583ed5fdfb28 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98504.txt @@ -0,0 +1,44 @@ +Maxim MAX98504 class D mono speaker amplifier + +This device supports I2C control interface and an IRQ output signal. It features +a PCM and PDM digital audio interface (DAI) and a differential analog input. + +Required properties: + + - compatible : "maxim,max98504" + - reg : should contain the I2C slave device address + - DVDD-supply, DIOVDD-supply, PVDD-supply: power supplies for the device, + as covered in ../regulator/regulator.txt + - interrupts : should specify the interrupt line the device is connected to, + as described in ../interrupt-controller/interrupts.txt + +Optional properties: + + - maxim,brownout-threshold - the PVDD brownout threshold, the value must be + from 0, 1...21 range, corresponding to 2.6V, 2.65V...3.65V voltage range + - maxim,brownout-attenuation - the brownout attenuation to the speaker gain + applied during the "attack hold" and "timed hold" phase, the value must be + from 0...6 (dB) range + - maxim,brownout-attack-hold-ms - the brownout attack hold phase time in ms, + 0...255 (VBATBROWN_ATTK_HOLD, register 0x0018) + - maxim,brownout-timed-hold-ms - the brownout timed hold phase time in ms, + 0...255 (VBATBROWN_TIME_HOLD, register 0x0019) + - maxim,brownout-release-rate-ms - the brownout release phase step time in ms, + 0...255 (VBATBROWN_RELEASE, register 0x001A) + +The default value when the above properties are not specified is 0, +the maxim,brownout-threshold property must be specified to actually enable +the PVDD brownout protection. + +Example: + + max98504@31 { + compatible = "maxim,max98504"; + reg = <0x31>; + interrupt-parent = <&gpio_bank_0>; + interrupts = <2 0>; + + DVDD-supply = <®ulator>; + DIOVDD-supply = <®ulator>; + PVDD-supply = <®ulator>; +}; diff --git a/Documentation/devicetree/bindings/sound/max9860.txt b/Documentation/devicetree/bindings/sound/max9860.txt new file mode 100644 index 000000000000..e0d4e95e31b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max9860.txt @@ -0,0 +1,28 @@ +MAX9860 Mono Audio Voice Codec + +Required properties: + + - compatible : "maxim,max9860" + + - reg : the I2C address of the device + + - AVDD-supply, DVDD-supply and DVDDIO-supply : power supplies for + the device, as covered in bindings/regulator/regulator.txt + + - clock-names : Required element: "mclk". + + - clocks : A clock specifier for the clock connected as MCLK. + +Examples: + + max9860: max9860@10 { + compatible = "maxim,max9860"; + reg = <0x10>; + + AVDD-supply = <®_1v8>; + DVDD-supply = <®_1v8>; + DVDDIO-supply = <®_3v0>; + + clock-names = "mclk"; + clocks = <&pck2>; + }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt new file mode 100644 index 000000000000..3e623a724e55 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -0,0 +1,150 @@ +Mediatek AFE PCM controller for mt2701 + +Required properties: +- compatible = "mediatek,mt2701-audio"; +- reg: register location and size +- interrupts: Should contain AFE interrupt +- clock-names: should have these clock names: + "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_mux1_div", + "top_audio_mux2_div", + "top_audio_48k_timing", + "top_audio_44k_timing", + "top_audpll_mux_sel", + "top_apll_sel", + "top_aud1_pll_98M", + "top_aud2_pll_90M", + "top_hadds2_pll_98M", + "top_hadds2_pll_294M", + "top_audpll", + "top_audpll_d4", + "top_audpll_d8", + "top_audpll_d16", + "top_audpll_d24", + "top_audintbus_sel", + "clk_26m", + "top_syspll1_d4", + "top_aud_k1_src_sel", + "top_aud_k2_src_sel", + "top_aud_k3_src_sel", + "top_aud_k4_src_sel", + "top_aud_k5_src_sel", + "top_aud_k6_src_sel", + "top_aud_k1_src_div", + "top_aud_k2_src_div", + "top_aud_k3_src_div", + "top_aud_k4_src_div", + "top_aud_k5_src_div", + "top_aud_k6_src_div", + "top_aud_i2s1_mclk", + "top_aud_i2s2_mclk", + "top_aud_i2s3_mclk", + "top_aud_i2s4_mclk", + "top_aud_i2s5_mclk", + "top_aud_i2s6_mclk", + "top_asm_m_sel", + "top_asm_h_sel", + "top_univpll2_d4", + "top_univpll2_d2", + "top_syspll_d5"; + +Example: + + afe: mt2701-afe-pcm@11220000 { + compatible = "mediatek,mt2701-audio"; + reg = <0 0x11220000 0 0x2000>, + <0 0x112A0000 0 0x20000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AUDIO>, + <&topckgen CLK_TOP_AUD_MUX1_SEL>, + <&topckgen CLK_TOP_AUD_MUX2_SEL>, + <&topckgen CLK_TOP_AUD_MUX1_DIV>, + <&topckgen CLK_TOP_AUD_MUX2_DIV>, + <&topckgen CLK_TOP_AUD_48K_TIMING>, + <&topckgen CLK_TOP_AUD_44K_TIMING>, + <&topckgen CLK_TOP_AUDPLL_MUX_SEL>, + <&topckgen CLK_TOP_APLL_SEL>, + <&topckgen CLK_TOP_AUD1PLL_98M>, + <&topckgen CLK_TOP_AUD2PLL_90M>, + <&topckgen CLK_TOP_HADDS2PLL_98M>, + <&topckgen CLK_TOP_HADDS2PLL_294M>, + <&topckgen CLK_TOP_AUDPLL>, + <&topckgen CLK_TOP_AUDPLL_D4>, + <&topckgen CLK_TOP_AUDPLL_D8>, + <&topckgen CLK_TOP_AUDPLL_D16>, + <&topckgen CLK_TOP_AUDPLL_D24>, + <&topckgen CLK_TOP_AUDINTBUS_SEL>, + <&clk26m>, + <&topckgen CLK_TOP_SYSPLL1_D4>, + <&topckgen CLK_TOP_AUD_K1_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K2_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K3_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K4_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K5_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K6_SRC_SEL>, + <&topckgen CLK_TOP_AUD_K1_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K2_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K3_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K4_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K5_SRC_DIV>, + <&topckgen CLK_TOP_AUD_K6_SRC_DIV>, + <&topckgen CLK_TOP_AUD_I2S1_MCLK>, + <&topckgen CLK_TOP_AUD_I2S2_MCLK>, + <&topckgen CLK_TOP_AUD_I2S3_MCLK>, + <&topckgen CLK_TOP_AUD_I2S4_MCLK>, + <&topckgen CLK_TOP_AUD_I2S5_MCLK>, + <&topckgen CLK_TOP_AUD_I2S6_MCLK>, + <&topckgen CLK_TOP_ASM_M_SEL>, + <&topckgen CLK_TOP_ASM_H_SEL>, + <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_UNIVPLL2_D2>, + <&topckgen CLK_TOP_SYSPLL_D5>; + + clock-names = "infra_sys_audio_clk", + "top_audio_mux1_sel", + "top_audio_mux2_sel", + "top_audio_mux1_div", + "top_audio_mux2_div", + "top_audio_48k_timing", + "top_audio_44k_timing", + "top_audpll_mux_sel", + "top_apll_sel", + "top_aud1_pll_98M", + "top_aud2_pll_90M", + "top_hadds2_pll_98M", + "top_hadds2_pll_294M", + "top_audpll", + "top_audpll_d4", + "top_audpll_d8", + "top_audpll_d16", + "top_audpll_d24", + "top_audintbus_sel", + "clk_26m", + "top_syspll1_d4", + "top_aud_k1_src_sel", + "top_aud_k2_src_sel", + "top_aud_k3_src_sel", + "top_aud_k4_src_sel", + "top_aud_k5_src_sel", + "top_aud_k6_src_sel", + "top_aud_k1_src_div", + "top_aud_k2_src_div", + "top_aud_k3_src_div", + "top_aud_k4_src_div", + "top_aud_k5_src_div", + "top_aud_k6_src_div", + "top_aud_i2s1_mclk", + "top_aud_i2s2_mclk", + "top_aud_i2s3_mclk", + "top_aud_i2s4_mclk", + "top_aud_i2s5_mclk", + "top_aud_i2s6_mclk", + "top_asm_m_sel", + "top_asm_h_sel", + "top_univpll2_d4", + "top_univpll2_d2", + "top_syspll_d5"; + }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt b/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt new file mode 100644 index 000000000000..05574446ceb6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt2701-cs42448.txt @@ -0,0 +1,43 @@ +MT2701 with CS42448 CODEC + +Required properties: +- compatible: "mediatek,mt2701-cs42448-machine" +- mediatek,platform: the phandle of MT2701 ASoC platform +- audio-routing: a list of the connections between audio +- mediatek,audio-codec: the phandles of cs42448 codec +- mediatek,audio-codec-bt-mrg the phandles of bt-sco dummy codec +- pinctrl-names: Should contain only one value - "default" +- pinctrl-0: Should specify pin control groups used for this controller. +- i2s1-in-sel-gpio1, i2s1-in-sel-gpio2: Should specify two gpio pins to + control I2S1-in mux. + +Example: + + sound:sound { + compatible = "mediatek,mt2701-cs42448-machine"; + mediatek,platform = <&afe>; + /* CS42448 Machine name */ + audio-routing = + "Line Out Jack", "AOUT1L", + "Line Out Jack", "AOUT1R", + "Line Out Jack", "AOUT2L", + "Line Out Jack", "AOUT2R", + "Line Out Jack", "AOUT3L", + "Line Out Jack", "AOUT3R", + "Line Out Jack", "AOUT4L", + "Line Out Jack", "AOUT4R", + "AIN1L", "AMIC", + "AIN1R", "AMIC", + "AIN2L", "Tuner In", + "AIN2R", "Tuner In", + "AIN3L", "Satellite Tuner In", + "AIN3R", "Satellite Tuner In", + "AIN3L", "AUX In", + "AIN3R", "AUX In"; + mediatek,audio-codec = <&cs42448>; + mediatek,audio-codec-bt-mrg = <&bt_sco_codec>; + pinctrl-names = "default"; + pinctrl-0 = <&aud_pins_default>; + i2s1-in-sel-gpio1 = <&pio 53 0>; + i2s1-in-sel-gpio2 = <&pio 54 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt index 5bfa6b60530b..29dce2ac8773 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt @@ -1,8 +1,9 @@ -MT8173 with RT5650 CODECS +MT8173 with RT5650 CODECS and HDMI via I2S Required properties: - compatible : "mediatek,mt8173-rt5650" - mediatek,audio-codec: the phandles of rt5650 codecs + and of the hdmi encoder node - mediatek,platform: the phandle of MT8173 ASoC platform Optional subnodes: @@ -12,12 +13,17 @@ Required codec-capture subnode properties: <&rt5650 0> : Default setting. Connect rt5650 I2S1 for capture. (dai_name = rt5645-aif1) <&rt5650 1> : Connect rt5650 I2S2 for capture. (dai_name = rt5645-aif2) +- mediatek,mclk: the MCLK source + 0 : external oscillator, MCLK = 12.288M + 1 : internal source from mt8173, MCLK = sampling rate*256 + Example: sound { compatible = "mediatek,mt8173-rt5650"; - mediatek,audio-codec = <&rt5650>; + mediatek,audio-codec = <&rt5650 &hdmi0>; mediatek,platform = <&afe>; + mediatek,mclk = <0>; codec-capture { sound-dai = <&rt5650 1>; }; diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt index 0741dff048dd..6f6c2f8e908d 100644 --- a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt +++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt @@ -8,6 +8,8 @@ Required properties: - interrupts: Interrupt number for McPDM - interrupt-parent: The parent interrupt controller - ti,hwmods: Name of the hwmod associated to the McPDM +- clocks: phandle for the pdmclk provider, likely <&twl6040> +- clock-names: Must be "pdmclk" Example: @@ -19,3 +21,11 @@ mcpdm: mcpdm@40132000 { interrupt-parent = <&gic>; ti,hwmods = "mcpdm"; }; + +In board DTS file the pdmclk needs to be added: + +&mcpdm { + clocks = <&twl6040>; + clock-names = "pdmclk"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index c7b29df4a963..15a7316e4c91 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -373,6 +373,8 @@ Optional properties: - #clock-cells : it must be 0 if your system has audio_clkout it must be 1 if your system has audio_clkout0/1/2/3 - clock-frequency : for all audio_clkout0/1/2/3 +- clkout-lr-asynchronous : boolean property. it indicates that audio_clkoutn + is asynchronizes with lr-clock. SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 6e86d8aa29b4..4ea29aa9af59 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -23,6 +23,11 @@ Required properties: - rockchip,playback-channels: max playback channels, if not set, 8 channels default. - rockchip,capture-channels: max capture channels, if not set, 2 channels default. +Required properties for controller which support multi channels +playback/capture: + +- rockchip,grf: the phandle of the syscon node for GRF register. + Example for rk3288 I2S controller: i2s@ff890000 { diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index e24436fc5ea9..9cabfc18cb57 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -8,6 +8,11 @@ Required properties: - reg : The I2C address of the device. +Optional properties: + +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt deleted file mode 100644 index 9148f72319e1..000000000000 --- a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt +++ /dev/null @@ -1,35 +0,0 @@ -Samsung Exynos Odroid X2/U3 audio complex with MAX98090 codec - -Required properties: - - compatible : "samsung,odroidx2-audio" - for Odroid X2 board, - "samsung,odroidu3-audio" - for Odroid U3 board - - samsung,model : the user-visible name of this sound complex - - samsung,i2s-controller : the phandle of the I2S controller - - samsung,audio-codec : the phandle of the MAX98090 audio codec - - samsung,audio-routing : a list of the connections between audio - components; each entry is a pair of strings, the first being the - connection's sink, the second being the connection's source; - valid names for sources and sinks are the MAX98090's pins (as - documented in its binding), and the jacks on the board - For Odroid X2: - * Headphone Jack - * Mic Jack - * DMIC - - For Odroid U3: - * Headphone Jack - * Speakers - -Example: - -sound { - compatible = "samsung,odroidu3-audio"; - samsung,i2s-controller = <&i2s0>; - samsung,audio-codec = <&max98090>; - samsung,model = "Odroid-X2"; - samsung,audio-routing = - "Headphone Jack", "HPL", - "Headphone Jack", "HPR", - "IN1", "Mic Jack", - "Mic Jack", "MICBIAS"; -}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 0e5e4eb3ef1b..5666da7b8605 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -7,6 +7,14 @@ Required properties: - clocks : the clock provider of SYS_MCLK +- VDDA-supply : the regulator provider of VDDA + +- VDDIO-supply: the regulator provider of VDDIO + +Optional properties: + +- VDDD-supply : the regulator provider of VDDD + - micbias-resistor-k-ohms : the bias resistor to be used in kOmhs The resistor can take values of 2k, 4k or 8k. If set to 0 it will be off. @@ -15,17 +23,9 @@ Required properties: - micbias-voltage-m-volts : the bias voltage to be used in mVolts The voltage can take values from 1.25V to 3V by 250mV steps - If this node is not mentionned or the value is unknown, then + If this node is not mentioned or the value is unknown, then the value is set to 1.25V. -- VDDA-supply : the regulator provider of VDDA - -- VDDIO-supply: the regulator provider of VDDIO - -Optional properties: - -- VDDD-supply : the regulator provider of VDDD - Example: codec: sgtl5000@0a { diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index cf3979eb3578..59d862801e59 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -30,7 +30,7 @@ Optional subnodes: sub-nodes. This container may be omitted when the card has only one DAI link. See the examples and the - section bellow. + section below. Dai-link subnode properties and subnodes: diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 4d9a83d9a017..16bcdfb6760e 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -33,11 +33,11 @@ Required properties: "tx" for "st,sti-uni-player" compatibility "rx" for "st,sti-uni-reader" compatibility - - version: IP version integrated in SOC. + - st,version: IP version integrated in SOC. - dai-name: DAI name that describes the IP. - - IP mode: IP working mode depending on associated codec. + - st,mode: IP working mode depending on associated codec. "HDMI" connected to HDMI codec and support IEC HDMI formats (player only). "SPDIF" connected to SPDIF codec and support SPDIF formats (player only). "PCM" PCM standard mode for I2S or TDM bus. @@ -47,7 +47,7 @@ Required properties ("st,sti-uni-player" compatibility only): - clocks: CPU_DAI IP clock source, listed in the same order than the CPU_DAI properties. - - uniperiph-id: internal SOC IP instance ID. + - st,uniperiph-id: internal SOC IP instance ID. Optional properties: - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for @@ -84,9 +84,9 @@ Example: dmas = <&fdma0 4 0 1>; dai-name = "Uni Player #2 (DAC)"; dma-names = "tx"; - uniperiph-id = <2>; - version = <5>; - mode = "PCM"; + st,uniperiph-id = <2>; + st,version = <5>; + st,mode = "PCM"; }; sti_uni_player3: sti-uni-player@3 { @@ -100,9 +100,9 @@ Example: dmas = <&fdma0 7 0 1>; dma-names = "tx"; dai-name = "Uni Player #3 (SPDIF)"; - uniperiph-id = <3>; - version = <5>; - mode = "SPDIF"; + st,uniperiph-id = <3>; + st,version = <5>; + st,mode = "SPDIF"; }; sti_uni_reader1: sti-uni-reader@1 { @@ -115,7 +115,7 @@ Example: dmas = <&fdma0 6 0 1>; dma-names = "rx"; dai-name = "Uni Reader #1 (HDMI RX)"; - version = <3>; + st,version = <3>; st,mode = "PCM"; }; diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt new file mode 100644 index 000000000000..7b526ec64991 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -0,0 +1,34 @@ +* Allwinner A10 I2S controller + +The I2S bus (Inter-IC sound bus) is a serial link for digital +audio data transfer between devices in the system. + +Required properties: + +- compatible: should be one of the followings + - "allwinner,sun4i-a10-i2s" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the I2S interrupt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should contain followings: + - "apb" : clock for the I2S bus interface + - "mod" : module clock for the I2S controller +- #sound-dai-cells : Must be equal to 0 + +Example: + +i2s0: i2s@01c22400 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-i2s"; + reg = <0x01c22400 0x400>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&apb0_gates 3>, <&i2s0_clk>; + clock-names = "apb", "mod"; + dmas = <&dma SUN4I_DMA_NORMAL 3>, + <&dma SUN4I_DMA_NORMAL 3>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 523341a0e113..8bc95e2fc47f 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -11,7 +11,6 @@ Required properties: - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" @@ -21,6 +20,9 @@ See the clock consumer binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { @@ -29,7 +31,6 @@ ecspi@70010000 { compatible = "fsl,imx51-ecspi"; reg = <0x70010000 0x4000>; interrupts = <36>; - fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ <&gpio3 25 0>; /* GPIO3_25 */ dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 42d595425dfb..17822860cb98 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -8,11 +8,10 @@ in slave mode. The SPI master node requires the following properties: - #address-cells - number of cells required to define a chip select - address on the SPI bus. + address on the SPI bus. - #size-cells - should be zero. - compatible - name of SPI bus controller following generic names - recommended practice. -- cs-gpios - (optional) gpios chip select. + recommended practice. No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -22,11 +21,12 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. -Optional property: -- num-cs : total number of chipselects +Optional properties: +- cs-gpios - gpios chip select. +- num-cs - total number of chipselects. -If cs-gpios is used the number of chip select will automatically increased -with max(cs-gpios > hw cs) +If cs-gpios is used the number of chip selects will be increased automatically +with max(cs-gpios > hw cs). So if for example the controller has 2 CS lines, and the cs-gpios property looks like this: @@ -45,29 +45,30 @@ SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. - compatible - (required) name of SPI device following generic names - recommended practice -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz + recommended practice. +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz. - spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode + inverse clock polarity (CPOL) mode. - spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode + shifted clock phase (CPHA) mode. - spi-cs-high - (optional) Empty property indicating device requires - chip select active high + chip select active high. - spi-3wire - (optional) Empty property indicating device requires - 3-wire mode. + 3-wire mode. - spi-lsb-first - (optional) Empty property indicating device requires LSB first mode. -- spi-tx-bus-width - (optional) The bus width(number of data wires) that +- spi-tx-bus-width - (optional) The bus width (number of data wires) that is used for MOSI. Defaults to 1 if not present. -- spi-rx-bus-width - (optional) The bus width(number of data wires) that +- spi-rx-bus-width - (optional) The bus width (number of data wires) that is used for MISO. Defaults to 1 if not present. - spi-rx-delay-us - (optional) Microsecond delay after a read transfer. - spi-tx-delay-us - (optional) Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 +wires (QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is -only 1(SINGLE), 2(DUAL) and 4(QUAD). +only 1 (SINGLE), 2 (DUAL) and 4 (QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed diff --git a/Documentation/devicetree/bindings/spi/spi-clps711x.txt b/Documentation/devicetree/bindings/spi/spi-clps711x.txt new file mode 100644 index 000000000000..4c3ec13f423f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-clps711x.txt @@ -0,0 +1,33 @@ +Serial Peripheral Interface on Cirrus Logic CL-PS71xx, EP72xx, EP73xx + +Required properties +- #address-cells: must be <1> +- #size-cells: must be <0> +- compatible: should include "cirrus,ep7209-spi" +- reg: Address and length of one register range +- interrupts: one interrupt line +- clocks: One entry, refers to the SPI bus clock +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +An additional register is present in the system controller, +which is assumed to be in the same device tree, with and marked +as compatible with "cirrus,ep7209-syscon3". + +Example: + +spi@80000500 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cirrus,ep7209-spi"; + reg = <0x80000500 0x4>; + interrupts = <15>; + clocks = <&clks CLPS711X_CLK_SPI>; + status = "disabled"; +}; + +syscon3: syscon@80002200 { + compatible = "cirrus,ep7209-syscon3", "syscon"; + reg = <0x80002200 0x40>; +}; + diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index d1e914adcf6e..f5916c92fe91 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -21,7 +21,7 @@ Required properties: IP to the interrupt controller within the SoC. Possible values are 0 and 1. Manual says one of the two possible interrupt lines can be tied to the interrupt controller. Set this - based on a specifc SoC configuration. + based on a specific SoC configuration. - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 98bc69815eb3..4f629cc7634a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -8,7 +8,15 @@ Required properties: - "marvell,armada-380-spi", for the Armada 38x SoCs - "marvell,armada-390-spi", for the Armada 39x SoCs - "marvell,armada-xp-spi", for the Armada XP SoCs -- reg : offset and length of the register set for the device +- reg : offset and length of the register set for the device. + This property can optionally have additional entries to configure + the SPI direct access mode that some of the Marvell SoCs support + additionally to the normal indirect access (PIO) mode. The values + for the MBus "target" and "attribute" are defined in the Marvell + SoC "Functional Specifications" Manual in the chapter "Marvell + Core Processor Address Decoding". + The eight register sets following the control registers refer to + chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. Optional properties: - interrupts : Is currently not used. @@ -23,3 +31,42 @@ Example: interrupts = <23>; status = "disabled"; }; + +Example with SPI direct mode support (optionally): + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */ + <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */ + <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */ + <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */ + <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */ + <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */ + <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */ + <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ + <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ + interrupts = <23>; + status = "disabled"; + }; + +To enable the direct mode, the board specific 'ranges' property in the +'soc' node needs to add the entries for the desired SPI controllers +and its chip-selects that are used in the direct mode instead of PIO +mode. Here an example for this (SPI controller 0, device 1 and SPI +controller 1, device 2 are used in direct mode. All other SPI device +are used in the default indirect (PIO) mode): + soc { + /* + * Enable the SPI direct access by configuring an entry + * here in the board-specific ranges property + */ + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */ + <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */ + <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */ + <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */ + +For further information on the MBus bindings, please see the MBus +DT documentation: +Documentation/devicetree/bindings/bus/mvebu-mbus.txt diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 1b14d69d8903..d2ca153614f9 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -6,10 +6,13 @@ and display controllers using the SPI communication interface. Required Properties: - compatible: should be one of the following. - "rockchip,rk3066-spi" for rk3066. - "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. - "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. - "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. + "rockchip,rk3036-spi" for rk3036 SoCS. + "rockchip,rk3066-spi" for rk3066 SoCs. + "rockchip,rk3188-spi" for rk3188 SoCs. + "rockchip,rk3228-spi" for rk3228 SoCS. + "rockchip,rk3288-spi" for rk3288 SoCs. + "rockchip,rk3368-spi" for rk3368 SoCs. + "rockchip,rk3399-spi" for rk3399 SoCs. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 6dbdeb3c361a..49028a4f5df1 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -9,7 +9,8 @@ Required SoC Specific Properties: - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - - samsung,exynos7-spi: for exynos7 platforms + - samsung,exynos5433-spi: for exynos5433 compatible controllers + - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED> - reg: physical base address of the controller and length of memory mapped region. @@ -23,6 +24,15 @@ Required SoC Specific Properties: - dma-names: Names for the dma channels. There must be at least one channel named "tx" for transmit and named "rx" for receive. +- clocks: specifies the clock IDs provided to the SPI controller; they are + required for interacting with the controller itself, for synchronizing the bus + and as I/O clock (the latter is required by exynos5433 and exynos7). + +- clock-names: string names of the clocks in the 'clocks' property; for all the + the devices the names must be "spi", "spi_busclkN" (where N is determined by + "samsung,spi-src-clk"), while Exynos5433 should specify a third clock + "spi_ioclk" for the I/O clock. + Required Board Specific Properties: - #address-cells: should be 1. @@ -40,6 +50,9 @@ Optional Board Specific Properties: - cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) +- no-cs-readback: the CS line is disconnected, therefore the device should not + operate based on CS signalling. + SPI Controller specific data in SPI slave nodes: - The spi slave nodes should provide the following information which is required diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 50b14f6b53a3..e65fde4a7388 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -20,7 +20,7 @@ Optional properties: chipselect register and offset of that register. NOTE: TI QSPI controller requires different pinmux and IODelay -paramaters for Mode-0 and Mode-3 operations, which needs to be set up by +parameters for Mode-0 and Mode-3 operations, which needs to be set up by the bootloader (U-Boot). Default configuration only supports Mode-0 operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be specified in the slave nodes of TI QSPI controller without appropriate diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt index 27cfc7d7ccd7..8d6e4fd2468e 100644 --- a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt +++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt @@ -9,7 +9,7 @@ Required properties: one) - clocks: phandle to the source clock (usually the AHB clock) -Optionnal properties: +Optional properties: - resets: phandle to a reset controller asserting the timer Example: diff --git a/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt new file mode 100644 index 000000000000..3ca89cd1caef --- /dev/null +++ b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt @@ -0,0 +1,17 @@ +Oxford Semiconductor OXNAS SoCs Family RPS Timer +================================================ + +Required properties: +- compatible: Should be "oxsemi,ox810se-rps-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupts of the two timers +- clocks : The phandle of the timer clock source + +example: + +timer0: timer@200 { + compatible = "oxsemi,ox810se-rps-timer"; + reg = <0x200 0x40>; + clocks = <&rpsclk>; + interrupts = <4 5>; +}; diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt index 87f0b0042bae..a41b184d5538 100644 --- a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt +++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt @@ -1,7 +1,9 @@ -Rockchip rk3288 timer +Rockchip rk timer Required properties: -- compatible: shall be "rockchip,rk3288-timer" +- compatible: shall be one of: + "rockchip,rk3288-timer" - for rk3066, rk3036, rk3188, rk322x, rk3288, rk3368 + "rockchip,rk3399-timer" - for rk3399 - reg: base address of the timer register starting with TIMERS CONTROL register - interrupts: should contain the interrupts for Timer0 - clocks : must contain an entry for each entry in clock-names diff --git a/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt new file mode 100644 index 000000000000..71c0777960e9 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt @@ -0,0 +1,26 @@ +* Universal Flash Storage (UFS) DesignWare Host Controller + +DWC_UFS nodes are defined to describe on-chip UFS host controllers and MPHY. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : compatible list must contain the PHY type & version: + "snps,g210-tc-6.00-20bit" + "snps,g210-tc-6.00-40bit" + complemented with the Controller IP version: + "snps,dwc-ufshcd-1.40a" + complemented with the JEDEC version: + "jedec,ufs-1.1" + "jedec,ufs-2.0" + +- reg : <registers mapping> +- interrupts : <interrupt mapping for UFS host controller IRQ> + +Example for a setup using a 1.40a DWC Controller with a 6.00 G210 40-bit TC: + dwc-ufs@d0000000 { + compatible = "snps,g210-tc-6.00-40bit", + "snps,dwc-ufshcd-1.40a", + "jedec,ufs-2.0"; + reg = < 0xd0000000 0x10000 >; + interrupts = < 24 >; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 66f6adf8d44d..a99ed5565b26 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -4,8 +4,8 @@ UFSHC nodes are defined to describe on-chip UFS host controllers. Each UFS controller instance should have its own node. Required properties: -- compatible : must contain "jedec,ufs-1.1", may also list one or more - of the following: +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may + also list one or more of the following: "qcom,msm8994-ufshc" "qcom,msm8996-ufshc" "qcom,ufshc" diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 1084e2bcbe1c..341dc67f3472 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -93,7 +93,7 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; - gadget-itc-setting = <0x4>; /* 4 micro-frames */ + itc-setting = <0x4>; /* 4 micro-frames */ /* Incremental burst of unspecified length */ ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 19233b7365e1..9df456968596 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -14,7 +14,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" -- resets : phandle + reset specifier pair +- resets : a list of phandle + reset specifier pairs Example: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2c2500df0dce..b9361816fc32 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -128,6 +128,7 @@ idt Integrated Device Technologies, Inc. ifi Ingenieurburo Fur Ic-Technologie (I/F/I) iom Iomega Corporation img Imagination Technologies Ltd. +infineon Infineon Technologies inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation @@ -214,6 +215,7 @@ raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International raspberrypi Raspberry Pi Foundation +raydium Raydium Semiconductor Corp. realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation richtek Richtek Technology Corporation @@ -254,6 +256,7 @@ syna Synaptics Inc. synology Synology, Inc. SUNW Sun Microsystems, Inc tbs TBS Technologies +tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt new file mode 100644 index 000000000000..c5e74d7b4406 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt @@ -0,0 +1,16 @@ +Aspeed Watchdog Timer + +Required properties: + - compatible: must be one of: + - "aspeed,ast2400-wdt" + - "aspeed,ast2500-wdt" + + - reg: physical base address of the controller and length of memory mapped + region + +Example: + + wdt1: watchdog@1e785000 { + compatible = "aspeed,ast2400-wdt"; + reg = <0x1e785000 0x1c>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt new file mode 100644 index 000000000000..c7fe36fa739c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt @@ -0,0 +1,16 @@ +Meson GXBB SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson-gxbb-wdt" +- reg : Specifies base physical address and size of the registers. +- clocks : Should be a phandle to the Watchdog clock source, for GXBB the xtal + is the default clock source. + +Example: + +wdt: watchdog@98d0 { + compatible = "amlogic,meson-gxbb-wdt"; + reg = <0 0x98d0 0x0 0x10>; + clocks = <&xtal>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt index 4726924d034e..41aeaa2ff0f8 100644 --- a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt @@ -7,6 +7,10 @@ Required properties : "qcom,kpss-wdt-msm8960" "qcom,kpss-wdt-apq8064" "qcom,kpss-wdt-ipq8064" + "qcom,kpss-wdt-ipq4019" + "qcom,kpss-timer" + "qcom,scss-timer" + "qcom,kpss-wdt" - reg : shall contain base register location and length - clocks : shall contain the input clock diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index b9512f1eb80a..da24e3133417 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -1,7 +1,11 @@ Renesas Watchdog Timer (WDT) Controller Required properties: -- compatible : Should be "renesas,r8a7795-wdt", or "renesas,rcar-gen3-wdt" +- compatible : Should be "renesas,<soctype>-wdt", and + "renesas,rcar-gen3-wdt" as fallback. + Examples with soctypes are: + - "renesas,r8a7795-wdt" (R-Car H3) + - "renesas,r8a7796-wdt" (R-Car M3-W) When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the generic |