diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
7 files changed, 116 insertions, 16 deletions
diff --git a/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt new file mode 100644 index 000000000000..4163e7eb7763 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt @@ -0,0 +1,10 @@ +* ARM SBSA defined generic UART +This UART uses a subset of the PL011 registers and consequently lives +in the PL011 driver. It's baudrate and other communication parameters +cannot be adjusted at runtime, so it lacks a clock specifier here. + +Required properties: +- compatible: must be "arm,sbsa-uart" +- reg: exactly one register range +- interrupts: exactly one interrupt specifier +- current-speed: the (fixed) baud rate set by the firmware diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 44152261e5c5..8d63f1da07aa 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -14,7 +14,14 @@ Required properties: - interrupts: A single interrupt specifier. -- clocks: Clock driving the hardware. +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: + - "baud": The clock the baudrate is derived from + - "bus": The bus clock for register accesses (optional) + +For compatibility with older device trees an unnamed clock is used for the +baud clock if the baudclk does not exist. Do not use this for new designs. Example: @@ -22,5 +29,6 @@ Example: compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart"; reg = <0x11006000 0x400>; interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>; - clocks = <&uart_clk>; + clocks = <&uart_clk>, <&bus_clk>; + clock-names = "baud", "bus"; }; diff --git a/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt new file mode 100644 index 000000000000..04e23e63ee4f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt @@ -0,0 +1,28 @@ +* NXP LPC1850 UART + +Required properties: +- compatible : "nxp,lpc1850-uart", "ns16550a". +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clocks : phandle to the input clocks. +- clock-names : required elements: "uartclk", "reg". + +Optional properties: +- dmas : Two or more DMA channel specifiers following the + convention outlined in bindings/dma/dma.txt +- dma-names : Names for the dma channels, if present. There must + be at least one channel named "tx" for transmit + and named "rx" for receive. + +Since it's also possible to also use the of_serial.c driver all +parameters from 8250.txt also apply but are optional. + +Example: +uart0: serial@40081000 { + compatible = "nxp,lpc1850-uart", "ns16550a"; + reg = <0x40081000 0x1000>; + reg-shift = <2>; + interrupts = <24>; + clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>; + clock-names = "uartclk", "reg"; +}; diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt index 246c795668dc..fbfe53635a3a 100644 --- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -1,4 +1,5 @@ * NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART) +* i2c as bus Required properties: - compatible: Should be one of the following: @@ -31,3 +32,39 @@ Example: gpio-controller; #gpio-cells = <2>; }; + +* spi as bus + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: SPI chip select number. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this IC. +- interrupts: Specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- clocks: phandle to the IC source clock. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + sc16is750: sc16is750@0 { + compatible = "nxp,sc16is750"; + reg = <0>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 7534d46e9ad8..e84b13a8eda3 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -45,6 +45,11 @@ Required properties: Note: Each enabled SCIx UART should have an alias correctly numbered in the "aliases" node. +Optional properties: + - dmas: Must contain a list of two references to DMA specifiers, one for + transmission, and one for reception. + - dma-names: Must contain a list of two DMA names, "tx" and "rx". + Example: aliases { serial0 = &scifa0; @@ -57,4 +62,6 @@ Example: interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>; clock-names = "sci_ick"; + dmas = <&dmac0 0x21>, <&dmac0 0x22>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt index f0c39261c5d4..67e2a0aeb042 100644 --- a/Documentation/devicetree/bindings/serial/sirf-uart.txt +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -2,8 +2,7 @@ Required properties: - compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart", - "sirf,atlas7-uart" or "sirf,atlas7-bt-uart" which means - uart located in BT module and used for BT. + "sirf,atlas7-uart" or "sirf,atlas7-usp-uart". - reg : Offset and length of the register set for the device - interrupts : Should contain uart interrupt - fifosize : Should define hardware rx/tx fifo size @@ -33,15 +32,3 @@ usp@b0090000 { rts-gpios = <&gpio 15 0>; cts-gpios = <&gpio 46 0>; }; - -for uart use in BT module, -uart6: uart@11000000 { - cell-index = <6>; - compatible = "sirf,atlas7-bt-uart", "sirf,atlas7-uart"; - reg = <0x11000000 0x1000>; - interrupts = <0 100 0>; - clocks = <&clks 138>, <&clks 140>, <&clks 141>; - clock-names = "uart", "general", "noc"; - fifosize = <128>; - status = "disabled"; -} diff --git a/Documentation/devicetree/bindings/serial/uniphier-uart.txt b/Documentation/devicetree/bindings/serial/uniphier-uart.txt new file mode 100644 index 000000000000..0b3892a7a528 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/uniphier-uart.txt @@ -0,0 +1,23 @@ +UniPhier UART controller + +Required properties: +- compatible: should be "socionext,uniphier-uart". +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +- fifo-size: the RX/TX FIFO size. Defaults to 64 if not specified. + +Example: + aliases { + serial0 = &serial0; + }; + + serial0: serial@54006800 { + compatible = "socionext,uniphier-uart"; + reg = <0x54006800 0x40>; + interrupts = <0 33 4>; + clocks = <&uart_clk>; + fifo-size = <64>; + }; |