diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/omap-usb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 39 |
1 files changed, 20 insertions, 19 deletions
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 9088ab09e200..090e5e22bd2b 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -3,9 +3,6 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" - - ti,has-mailbox : to specify that omap uses an external mailbox - (in control module) to communicate with the musb core during device connect - and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num-eps : Specifies the number of endpoints. This is also a @@ -19,6 +16,9 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply up to 100mA when operating in host mode. - usb-phy : the phandle for the PHY device + - phys : the phandle for the PHY device (used by generic PHY framework) + - phy-names : the names of the PHY corresponding to the PHYs present in the + *phy* phandle. Optional properties: - ctrl-module : phandle of the control module this glue uses to write to @@ -28,11 +28,12 @@ SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; - ti,has-mailbox; multipoint = <1>; num-eps = <16>; ram-bits = <12>; ctrl-module = <&omap_control_usb>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; }; Board specific device node entry @@ -78,22 +79,22 @@ omap_dwc3 { OMAP CONTROL USB Required properties: - - compatible: Should be "ti,omap-control-usb" + - compatible: Should be one of + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register + e.g. USB2_PHY on OMAP5. + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control + e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on + DRA7 platform. - reg : Address and length of the register set for the device. It contains - the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" - depending upon omap4 or omap5. - - reg-names: The names of the register addresses corresponding to the registers - filled in "reg". - - ti,type: This is used to differentiate whether the control module has - usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to - notify events to the musb core and omap5 has usb3 phy power register to - power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 - phy power. + the address of "otghs_control" for control-phy-otghs or "power" register + for other types. + - reg-names: should be "otghs_control" control-phy-otghs and "power" for + other types. omap_control_usb: omap-control-usb@4a002300 { - compatible = "ti,omap-control-usb"; - reg = <0x4a002300 0x4>, - <0x4a00233c 0x4>; - reg-names = "control_dev_conf", "otghs_control"; - ti,type = <1>; + compatible = "ti,control-phy-otghs"; + reg = <0x4a00233c 0x4>; + reg-names = "otghs_control"; }; |