diff options
Diffstat (limited to 'Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt | 90 |
1 files changed, 0 insertions, 90 deletions
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt deleted file mode 100644 index d0fee78e6203..000000000000 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ /dev/null @@ -1,90 +0,0 @@ -* Universal Flash Storage (UFS) Host Controller - -UFSHC nodes are defined to describe on-chip UFS host controllers. -Each UFS controller instance should have its own node. - -Required properties: -- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0" - - For Qualcomm SoCs must contain, as below, an - SoC-specific compatible along with "qcom,ufshc" and - the appropriate jedec string: - "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,sm8250-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,sm8350-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - "qcom,sm8450-ufshc", "qcom,ufshc", "jedec,ufs-2.0" -- interrupts : <interrupt mapping for UFS host controller IRQ> -- reg : <registers mapping> - -Optional properties: -- phys : phandle to UFS PHY node -- phy-names : the string "ufsphy" when is found in a node, along - with "phys" attribute, provides phandle to UFS PHY node -- vdd-hba-supply : phandle to UFS host controller supply regulator node -- vcc-supply : phandle to VCC supply regulator node -- vccq-supply : phandle to VCCQ supply regulator node -- vccq2-supply : phandle to VCCQ2 supply regulator node -- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V - or 2.7-3.6V. This boolean property when set, specifies - to use low voltage range of 1.7-1.95V. Note for external - UFS cards this property is invalid and valid VCC range is - always 2.7-3.6V. -- vcc-max-microamp : specifies max. load that can be drawn from vcc supply -- vccq-max-microamp : specifies max. load that can be drawn from vccq supply -- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply - -- clocks : List of phandle and clock specifier pairs -- clock-names : List of clock input name strings sorted in the same - order as the clocks property. - "ref_clk" indicates reference clock frequency. - UFS host supplies reference clock to UFS device and UFS device - specification allows host to provide one of the 4 frequencies (19.2 MHz, - 26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is - parsed and used to update the reference clock setting in device. - Defaults to 26 MHz(as per specification) if not specified by host. -- freq-table-hz : Array of <min max> operating frequencies stored in the same - order as the clocks property. If this property is not - defined or a value in the array is "0" then it is assumed - that the frequency is set by the parent clock or a - fixed rate clock source. --lanes-per-direction : number of lanes available per direction - either 1 or 2. - Note that it is assume same number of lanes is used both - directions at once. If not specified, default is 2 lanes per direction. -- #reset-cells : Must be <1> for Qualcomm UFS controllers that expose - PHY reset from the UFS controller. -- resets : reset node register -- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP. -- reset-gpios : A phandle and gpio specifier denoting the GPIO connected - to the RESET pin of the UFS memory device. - -Note: If above properties are not defined it can be assumed that the supply -regulators or clocks are always on. - -Example: - ufshc@fc598000 { - compatible = "jedec,ufs-1.1"; - reg = <0xfc598000 0x800>; - interrupts = <0 28 0>; - - vdd-hba-supply = <&xxx_reg0>; - vcc-supply = <&xxx_reg1>; - vcc-supply-1p8; - vccq-supply = <&xxx_reg2>; - vccq2-supply = <&xxx_reg3>; - vcc-max-microamp = 500000; - vccq-max-microamp = 200000; - vccq2-max-microamp = 200000; - - clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>; - clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk"; - freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>; - resets = <&reset 0 1>; - reset-names = "rst"; - phys = <&ufsphy1>; - phy-names = "ufsphy"; - #reset-cells = <1>; - }; |