diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
5 files changed, 40 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt index 2c1e6a43930b..e0fa61a1be0c 100644 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -19,7 +19,7 @@ Recommended properties : Example: -spi1: spi@0x4000c400 { /* USART1 */ +spi1: spi@4000c400 { /* USART1 */ #address-cells = <1>; #size-cells = <0>; compatible = "energymicro,efm32-spi"; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 5bf13960f7f4..e3c48b20b1a6 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -12,24 +12,30 @@ Required properties: - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" See the clock consumer binding, Documentation/devicetree/bindings/clock/clock-bindings.txt -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "tx" and "rx" if present. -Obsolete properties: -- fsl,spi-num-chipselects : Contains the number of the chipselect +Recommended properties: +- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip +select lines can be used, they appear to always generate a pulse between each +word of a transfer. Most use cases will require GPIO based chip selects to +generate a valid transaction. Optional properties: +- num-cs : Number of total chip selects, see spi-bus.txt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names, if present, should include "tx" and "rx". - fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register controlling the SPI_READY handling. Note that to enable the DRCTL consideration, the SPI_READY mode-flag needs to be set too. Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bdd83959019c..80710f0f0448 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -36,7 +36,21 @@ Required properties: Optional properties: - clocks : Must contain a reference to the functional clock. -- num-cs : Total number of chip-selects (default is 1) +- num-cs : Total number of chip selects (default is 1). + Up to 3 native chip selects are supported: + 0: MSIOF_SYNC + 1: MSIOF_SS1 + 2: MSIOF_SS2 + Hardware limitations related to chip selects: + - Native chip selects are always deasserted in + between transfers that are part of the same + message. Use cs-gpios to work around this. + - All slaves using native chip selects must use the + same spi-cs-high configuration. Use cs-gpios to + work around this. + - When using GPIO chip selects, at least one native + chip select must be left unused, as it will be + driven anyway. - dmas : Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index 825c39cae74a..b7f5e86fed22 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -27,7 +27,9 @@ The Meson SPICC is generic SPI controller for general purpose Full-Duplex communications with dedicated 16 words RX/TX PIO FIFOs. Required properties: - - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs. + - compatible: should be: + "amlogic,meson-gx-spicc" on Amlogic GX and compatible SoCs. + "amlogic,meson-axg-spicc" on Amlogic AXG and compatible SoCs - reg: physical base address and length of the controller registers - interrupts: The interrupt specifier - clock-names: Must contain "core" diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index df8ec31f2f07..8434a65fc12a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -18,8 +18,17 @@ Required properties: The eight register sets following the control registers refer to chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. +- clocks : pointers to the reference clocks for this device, the first + one is the one used for the clock on the spi bus, the + second one is optional and is the clock used for the + functional part of the controller + Optional properties: - interrupts : Is currently not used. +- clock-names : names of used clocks, mandatory if the second clock is + used, the name must be "core", and "axi" (the latter + is only for Armada 7K/8K). + Example: spi@10600 { |