diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
4 files changed, 43 insertions, 4 deletions
diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index f80887bca0d6..12ecfe9e3599 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -1,5 +1,10 @@ Davinci SPI controller device bindings +Links on DM: +Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf +dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf +OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf + Required properties: - #address-cells: number of cells required to define a chip select address on the SPI bus. Should be set to 1. @@ -24,6 +29,30 @@ Optional: cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; where first three are internal CS and last two are GPIO CS. +Optional properties for slave devices: +SPI slave nodes can contain the following properties. +Not all SPI Peripherals from Texas Instruments support this. +Please check SPI peripheral documentation for a device before using these. + +- ti,spi-wdelay : delay between transmission of words + (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module + clock periods. + + delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period + +Below is timing diagram which shows functional meaning of +"ti,spi-wdelay" parameter. + + +-+ +-+ +-+ +-+ +-+ +-+ +-+ +-+ +SPI_CLK | | | | | | | | | | | | | | | | + +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +- + +SPI_SOMI/SIMO+-----------------+ +----------- + +----------+ word1 +---------------------------+word2 + +-----------------+ +----------- + WDELAY + <--------------------------> + Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus. @@ -43,6 +72,7 @@ spi0:spi@20BF0000 { compatible = "st,m25p32"; spi-max-frequency = <25000000>; reg = <0>; + ti,spi-wdelay = <8>; partition@0 { label = "u-boot-spl"; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index 5376de40f10b..cbbe16ed3874 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -10,7 +10,12 @@ Required properties: - pinctrl-names: must contain a "default" entry. - spi-num-chipselects : the number of the chipselect signals. - bus-num : the slave chip chipselect signal number. -- big-endian : if DSPI modudle is big endian, the bool will be set in node. + +Optional property: +- big-endian: If present the dspi device's registers are implemented + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + Example: dspi0@4002c000 { diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index a3ff50fc76fb..50c3a3de61c1 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -1,7 +1,7 @@ Marvell Orion SPI device Required properties: -- compatible : should be "marvell,orion-spi". +- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi". - reg : offset and length of the register set for the device - cell-index : Which of multiple SPI controllers is this. Optional properties: diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 7bab35575817..467dec441c62 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -16,11 +16,15 @@ Required Properties: - clocks: Must contain an entry for each entry in clock-names. - clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk" for the peripheral clock. +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional Properties: + - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. -- #address-cells: should be 1. -- #size-cells: should be 0. + Example: |