diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
5 files changed, 167 insertions, 35 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs43130.txt b/Documentation/devicetree/bindings/sound/cs43130.txt new file mode 100644 index 000000000000..8b1dd5aeb004 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs43130.txt @@ -0,0 +1,67 @@ +CS43130 DAC + +Required properties: + + - compatible : "cirrus,cs43130", "cirrus,cs4399", "cirrus,cs43131", + "cirrus,cs43198" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply, VL-supply, VCP-supply, VD-supply: + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + +Optional properties: + + - reset-gpios : Active low GPIO used to reset the device + + - cirrus,xtal-ibias: + When external MCLK is generated by external crystal + oscillator, CS43130 can be used to provide bias current + for external crystal. Amount of bias current sent is + set as: + 1 = 7.5uA + 2 = 12.5uA + 3 = 15uA + + - cirrus,dc-measure: + Boolean, define to enable headphone DC impedance measurement. + + - cirrus,ac-measure: + Boolean, define to enable headphone AC impedance measurement. + DC impedance must also be enabled for AC impedance measurement. + + - cirrus,dc-threshold: + Define 2 DC impedance thresholds in ohms for HP output control. + Default values are 50 and 120 Ohms. + + - cirrus,ac-freq: + Define the frequencies at which to measure HP AC impedance. + Only used if "cirrus,dc-measure" is defined. + Exactly 10 frequencies must be defined. + If this properties is undefined, by default, + following frequencies are used: + <24 43 93 200 431 928 2000 4309 9283 20000> + The above frequencies are logarithmically equally spaced. + Log base is 10. + +Example: + +cs43130: audio-codec@30 { + compatible = "cirrus,cs43130"; + reg = <0x30>; + reset-gpios = <&axi_gpio 54 0>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD-supply = <&dummy_vreg>; + cirrus,xtal-ibias = <2>; + interrupt-parent = <&gpio0>; + interrupts = <55 8>; + cirrus,dc-measure; + cirrus,ac-measure; + cirrus,dc-threshold = /bits/ 16 <20 100>; + cirrus,ac-freq = /bits/ 16 <24 43 93 200 431 928 2000 4309 9283 20000>; +}; diff --git a/Documentation/devicetree/bindings/sound/dmic.txt b/Documentation/devicetree/bindings/sound/dmic.txt new file mode 100644 index 000000000000..54c8ef6498a8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/dmic.txt @@ -0,0 +1,16 @@ +Device-Tree bindings for Digital microphone (DMIC) codec + +This device support generic PDM digital microphone. + +Required properties: + - compatible: should be "dmic-codec". + +Optional properties: + - dmicen-gpios: GPIO specifier for dmic to control start and stop + +Example node: + + dmic_codec: dmic@0 { + compatible = "dmic-codec"; + dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt index ccb401cfef9d..551ecab67efe 100644 --- a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -31,8 +31,22 @@ Required properties - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. - Optional Properties: + - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons + detection on headset when the mbhc is powered up + by internal current source, this is a low power. + - qcom,mbhc-vthreshold-high: Array of 5 thresold voltages in mV for 5 buttons + detection on headset when mbhc is powered up + from micbias. +- qcom,micbias-lvl: Voltage (mV) for Mic Bias +- qcom,hphl-jack-type-normally-open: boolean, present if hphl pin on jack is a + NO (Normally Open). If not specified, then + its assumed that hphl pin on jack is NC + (Normally Closed). +- qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is + NO (Normally Open). If not specified, then + its assumed that gnd pin on jack is NC + (Normally Closed). - qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor connected. - qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor @@ -48,6 +62,8 @@ spmi_bus { reg-names = "pmic-codec-core"; clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; clock-names = "mclk"; + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; interrupt-parent = <&spmi_bus>; interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, <0x1 0xf0 0x1 IRQ_TYPE_NONE>, diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 7246bb268bf9..a1536fdc60e6 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -199,10 +199,10 @@ Ex) sound { compatible = "simple-scu-audio-card"; ... - simple-audio-card,cpu@0 { + simple-audio-card,cpu-0 { sound-dai = <&rcar_sound 0>; }; - simple-audio-card,cpu@1 { + simple-audio-card,cpu-1 { sound-dai = <&rcar_sound 1>; }; simple-audio-card,codec { @@ -441,79 +441,79 @@ rcar_sound: sound@ec500000 { "clk_a", "clk_b", "clk_c", "clk_i"; rcar_sound,dvc { - dvc0: dvc@0 { + dvc0: dvc-0 { dmas = <&audma0 0xbc>; dma-names = "tx"; }; - dvc1: dvc@1 { + dvc1: dvc-1 { dmas = <&audma0 0xbe>; dma-names = "tx"; }; }; rcar_sound,mix { - mix0: mix@0 { }; - mix1: mix@1 { }; + mix0: mix-0 { }; + mix1: mix-1 { }; }; rcar_sound,ctu { - ctu00: ctu@0 { }; - ctu01: ctu@1 { }; - ctu02: ctu@2 { }; - ctu03: ctu@3 { }; - ctu10: ctu@4 { }; - ctu11: ctu@5 { }; - ctu12: ctu@6 { }; - ctu13: ctu@7 { }; + ctu00: ctu-0 { }; + ctu01: ctu-1 { }; + ctu02: ctu-2 { }; + ctu03: ctu-3 { }; + ctu10: ctu-4 { }; + ctu11: ctu-5 { }; + ctu12: ctu-6 { }; + ctu13: ctu-7 { }; }; rcar_sound,src { - src0: src@0 { + src0: src-0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x85>, <&audma1 0x9a>; dma-names = "rx", "tx"; }; - src1: src@1 { + src1: src-1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x87>, <&audma1 0x9c>; dma-names = "rx", "tx"; }; - src2: src@2 { + src2: src-2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x89>, <&audma1 0x9e>; dma-names = "rx", "tx"; }; - src3: src@3 { + src3: src-3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8b>, <&audma1 0xa0>; dma-names = "rx", "tx"; }; - src4: src@4 { + src4: src-4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8d>, <&audma1 0xb0>; dma-names = "rx", "tx"; }; - src5: src@5 { + src5: src-5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8f>, <&audma1 0xb2>; dma-names = "rx", "tx"; }; - src6: src@6 { + src6: src-6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x91>, <&audma1 0xb4>; dma-names = "rx", "tx"; }; - src7: src@7 { + src7: src-7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x93>, <&audma1 0xb6>; dma-names = "rx", "tx"; }; - src8: src@8 { + src8: src-8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x95>, <&audma1 0xb8>; dma-names = "rx", "tx"; }; - src9: src@9 { + src9: src-9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x97>, <&audma1 0xba>; dma-names = "rx", "tx"; @@ -521,52 +521,52 @@ rcar_sound: sound@ec500000 { }; rcar_sound,ssi { - ssi0: ssi@0 { + ssi0: ssi-0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi1: ssi@1 { + ssi1: ssi-1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi2: ssi@2 { + ssi2: ssi-2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi3: ssi@3 { + ssi3: ssi-3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi4: ssi@4 { + ssi4: ssi-4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi5: ssi@5 { + ssi5: ssi-5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi6: ssi@6 { + ssi6: ssi-6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi7: ssi@7 { + ssi7: ssi-7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi8: ssi@8 { + ssi8: ssi-8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi9: ssi@9 { + ssi9: ssi-9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; dma-names = "rx", "tx", "rxu", "txu"; diff --git a/Documentation/devicetree/bindings/sound/rt274.txt b/Documentation/devicetree/bindings/sound/rt274.txt new file mode 100644 index 000000000000..e9a6178c78cf --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt274.txt @@ -0,0 +1,33 @@ +RT274 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt274". + +- reg : The I2C address of the device. + +Optional properties: + +- interrupts : The CODEC's interrupt output. + + +Pins on the device (for linking into audio routes) for RT274: + + * DMIC1 Pin + * DMIC2 Pin + * MIC + * LINE1 + * LINE2 + * HPO Pin + * SPDIF + * LINE3 + +Example: + +codec: rt274@1c { + compatible = "realtek,rt274"; + reg = <0x1c>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; +}; |