1 files changed, 0 insertions, 111 deletions
diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt
deleted file mode 100644
index a9c34526f4cb..000000000000
--- a/Documentation/devicetree/bindings/sound/nau8825.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-Nuvoton NAU8825 audio codec
-
-This device supports I2C only.
-
-Required properties:
-  - compatible : Must be "nuvoton,nau8825"
-
-  - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
-
-Optional properties:
-  - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
-  - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
-      otherwise pin in high impedance state.
-  - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
-  - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
-
-  - nuvoton,vref-impedance: VREF Impedance selection
-      0 - Open
-      1 - 25 kOhm
-      2 - 125 kOhm
-      3 - 2.5 kOhm
-
-  - nuvoton,micbias-voltage: Micbias voltage level.
-      0 - VDDA
-      1 - VDDA
-      2 - VDDA * 1.1
-      3 - VDDA * 1.2
-      4 - VDDA * 1.3
-      5 - VDDA * 1.4
-      6 - VDDA * 1.53
-      7 - VDDA * 1.53
-
-  - nuvoton,sar-threshold-num: Number of buttons supported
-  - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
-    SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
-    where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
-    Refer datasheet section 10.2 for more information about threshold calculation.
-
-  - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
-
-  - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
-      0 - VDDA
-      1 - VDDA
-      2 - VDDA * 1.1
-      3 - VDDA * 1.2
-      4 - VDDA * 1.3
-      5 - VDDA * 1.4
-      6 - VDDA * 1.53
-      7 - VDDA * 1.53
-
-  - nuvoton,sar-compare-time: SAR compare time
-      0 - 500 ns
-      1 - 1 us
-      2 - 2 us
-      3 - 4 us
-
-  - nuvoton,sar-sampling-time: SAR sampling time
-      0 - 2 us
-      1 - 4 us
-      2 - 8 us
-      3 - 16 us
-
-  - nuvoton,short-key-debounce: Button short key press debounce time.
-      0 - 30 ms
-      1 - 50 ms
-      2 - 100 ms
-      3 - 30 ms
-
-  - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
-  - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
-
-  - nuvoton,crosstalk-enable: make crosstalk function enable if set.
-
-  - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set.
-      Otherwise, the drive keeps normal strength.
-
-  - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The
-      default value is 125 and range between 125 to 500 ms.
-
-  - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
-      clocks described in clock-names
-  - clock-names: should include "mclk" for the MCLK master clock
-
-Example:
-
-  headset: nau8825@1a {
-      compatible = "nuvoton,nau8825";
-      reg = <0x1a>;
-      interrupt-parent = <&gpio>;
-      interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
-      nuvoton,jkdet-enable;
-      nuvoton,jkdet-pull-enable;
-      nuvoton,jkdet-pull-up;
-      nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
-      nuvoton,vref-impedance = <2>;
-      nuvoton,micbias-voltage = <6>;
-      // Setup 4 buttons impedance according to Android specification
-      nuvoton,sar-threshold-num = <4>;
-      nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
-      nuvoton,sar-hysteresis = <1>;
-      nuvoton,sar-voltage = <0>;
-      nuvoton,sar-compare-time = <0>;
-      nuvoton,sar-sampling-time = <0>;
-      nuvoton,short-key-debounce = <2>;
-      nuvoton,jack-insert-debounce = <7>;
-      nuvoton,jack-eject-debounce = <7>;
-      nuvoton,crosstalk-enable;
-
-      clock-names = "mclk";
-      clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>;
-  };