2 files changed, 108 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt b/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt
new file mode 100644
index 000000000000..510c748656ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt
@@ -0,0 +1,52 @@
+Qualcomm AOSS Reset Controller
+======================================
+
+This binding describes a reset-controller found on AOSS-CC (always on subsystem)
+for Qualcomm SDM845 SoCs.
+
+Required properties:
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be:
+		    "qcom,sdm845-aoss-cc"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: must specify the base address and size of the register
+	            space.
+
+- #reset-cells:
+	Usage: required
+	Value type: <uint>
+	Definition: must be 1; cell entry represents the reset index.
+
+Example:
+
+aoss_reset: reset-controller@c2a0000 {
+	compatible = "qcom,sdm845-aoss-cc";
+	reg = <0xc2a0000 0x31000>;
+	#reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+
+Device nodes that need access to reset lines should
+specify them as a reset phandle in their corresponding node as
+specified in reset.txt.
+
+For list of all valid reset indicies see
+<dt-bindings/reset/qcom,sdm845-aoss.h>
+
+Example:
+
+modem-pil@4080000 {
+	...
+
+	resets = <&aoss_reset AOSS_CC_MSS_RESTART>;
+	reset-names = "mss_restart";
+
+	...
+};
diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt
index 93efed629900..101743dda223 100644
--- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt
+++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt
@@ -118,3 +118,59 @@ Example:
 
 		other nodes ...
 	};
+
+
+USB3 core reset
+---------------
+
+USB3 core reset belongs to USB3 glue layer. Before using the core reset,
+it is necessary to control the clocks and resets to enable this layer.
+These clocks and resets should be described in each property.
+
+Required properties:
+- compatible: Should be
+    "socionext,uniphier-pro4-usb3-reset" - for Pro4 SoC
+    "socionext,uniphier-pxs2-usb3-reset" - for PXs2 SoC
+    "socionext,uniphier-ld20-usb3-reset" - for LD20 SoC
+    "socionext,uniphier-pxs3-usb3-reset" - for PXs3 SoC
+- #reset-cells: Should be 1.
+- reg: Specifies offset and length of the register set for the device.
+- clocks: A list of phandles to the clock gate for USB3 glue layer.
+	According to the clock-names, appropriate clocks are required.
+- clock-names: Should contain
+    "gio", "link" - for Pro4 SoC
+    "link"        - for others
+- resets: A list of phandles to the reset control for USB3 glue layer.
+	According to the reset-names, appropriate resets are required.
+- reset-names: Should contain
+    "gio", "link" - for Pro4 SoC
+    "link"        - for others
+
+Example:
+
+	usb-glue@65b00000 {
+		compatible = "socionext,uniphier-ld20-dwc3-glue",
+			     "simple-mfd";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x65b00000 0x400>;
+
+		usb_rst: reset@0 {
+			compatible = "socionext,uniphier-ld20-usb3-reset";
+			reg = <0x0 0x4>;
+			#reset-cells = <1>;
+			clock-names = "link";
+			clocks = <&sys_clk 14>;
+			reset-names = "link";
+			resets = <&sys_rst 14>;
+		};
+
+		regulator {
+			...
+		};
+
+		phy {
+			...
+		};
+		...
+	};