diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power')
3 files changed, 66 insertions, 23 deletions
diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 14bd9e945ff6..f3355313c020 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -40,6 +40,12 @@ Optional properties: domain's idle states. In the absence of this property, the domain would be considered as capable of being powered-on or powered-off. +- operating-points-v2 : Phandles to the OPP tables of power domains provided by + a power domain provider. If the provider provides a single power domain only + or all the power domains provided by the provider have identical OPP tables, + then this shall contain a single phandle. Refer to ../opp/opp.txt for more + information. + Example: power: power-controller@12340000 { @@ -120,4 +126,63 @@ The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". +Optional properties: +- required-opp: This contains phandle to an OPP node in another device's OPP + table. It may contain an array of phandles, where each phandle points to an + OPP of a different device. It should not contain multiple phandles to the OPP + nodes in the same OPP table. This specifies the minimum required OPP of the + device(s), whose OPP's phandle is present in this property, for the + functioning of the current device at the current OPP (where this property is + present). + +Example: +- OPP table for domain provider that provides two domains. + + domain0_opp_table: opp-table0 { + compatible = "operating-points-v2"; + + domain0_opp_0: opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain0_opp_1: opp-1100000000 { + opp-hz = /bits/ 64 <1100000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + domain1_opp_table: opp-table1 { + compatible = "operating-points-v2"; + + domain1_opp_0: opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain1_opp_1: opp-1300000000 { + opp-hz = /bits/ 64 <1300000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + power: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + operating-points-v2 = <&domain0_opp_table>, <&domain1_opp_table>; + }; + + leaky-device0@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 0>; + required-opp = <&domain0_opp_0>; + }; + + leaky-device1@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 1>; + required-opp = <&domain1_opp_1>; + }; + [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt deleted file mode 100644 index 1b81fcd9fb72..000000000000 --- a/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt +++ /dev/null @@ -1,23 +0,0 @@ -i.mx6 Poweroff Driver - -SNVS_LPCR in SNVS module can power off the whole system by pull -PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. -If you don't want to use PMIC_ON_REQ as power on/off control, -please set status='disabled' to disable this driver. - -Required Properties: --compatible: "fsl,sec-v4.0-poweroff" --reg: Specifies the physical address of the SNVS_LPCR register - -Example: - snvs@20cc000 { - compatible = "fsl,sec-v4.0-mon", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x020cc000 0x4000>; - ..... - snvs_poweroff: snvs-poweroff@38 { - compatible = "fsl,sec-v4.0-poweroff"; - reg = <0x38 0x4>; - }; - } diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index 6858e1a804ad..615c1cb6889f 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -15,6 +15,7 @@ Required properties: * "ti,bq27520g2" - BQ27520-g2 * "ti,bq27520g3" - BQ27520-g3 * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27521" - BQ27521 * "ti,bq27530" - BQ27530 * "ti,bq27531" - BQ27531 * "ti,bq27541" - BQ27541 |