diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
7 files changed, 240 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt index 35d4a979bb7b..89a84f8aa621 100644 --- a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt +++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt @@ -30,6 +30,13 @@ Mandatory properties: 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as pre-fetchable. +Optional properties: +- clocks: when present, this should contain the peripheral clock (PCLK) and the + PCI clock (PCICLK). If these are not present, they are assumed to be + hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz. +- clock-names: when present, this should contain "PCLK" for the peripheral + clock and "PCICLK" for the PCI-side clock. + Mandatory subnodes: - For "faraday,ftpci100" a node representing the interrupt-controller inside the host bridge is mandatory. It has the following mandatory properties: diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index e3d5680875b1..cf92d3ba5a26 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -33,6 +33,10 @@ Optional properties: - reset-gpio-active-high: If present then the reset sequence using the GPIO specified in the "reset-gpio" property is reversed (H=reset state, L=operation state). +- vpcie-supply: Should specify the regulator in charge of PCIe port power. + The regulator will be enabled when initializing the PCIe host and + disabled either as part of the init process or when shutting down the + host. Additional required properties for imx6sx-pcie: - clock names: Must include the following additional entries: diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt new file mode 100644 index 000000000000..68ffa0fbcd73 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt @@ -0,0 +1,50 @@ +HiSilicon Kirin SoCs PCIe host DT description + +Kirin PCIe host controller is based on Designware PCI core. +It shares common functions with PCIe Designware core driver +and inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt. + +Additional properties are described here: + +Required properties +- compatible: + "hisilicon,kirin960-pcie" for PCIe of Kirin960 SoC +- reg: Should contain rc_dbi, apb, phy, config registers location and length. +- reg-names: Must include the following entries: + "dbi": controller configuration registers; + "apb": apb Ctrl register defined by Kirin; + "phy": apb PHY register defined by Kirin; + "config": PCIe configuration space registers. +- reset-gpios: The gpio to generate PCIe perst assert and deassert signal. + +Optional properties: + +Example based on kirin960: + + pcie@f4000000 { + compatible = "hisilicon,kirin-pcie"; + reg = <0x0 0xf4000000 0x0 0x1000>, <0x0 0xff3fe000 0x0 0x1000>, + <0x0 0xf3f20000 0x0 0x40000>, <0x0 0xF4000000 0 0x2000>; + reg-names = "dbi","apb","phy", "config"; + bus-range = <0x0 0x1>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x02000000 0x0 0x00000000 0x0 0xf5000000 0x0 0x2000000>; + num-lanes = <1>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &gic 0 0 0 282 4>, + <0x0 0 0 2 &gic 0 0 0 283 4>, + <0x0 0 0 3 &gic 0 0 0 284 4>, + <0x0 0 0 4 &gic 0 0 0 285 4>; + clocks = <&crg_ctrl HI3660_PCIEPHY_REF>, + <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>, + <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>, + <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>, + <&crg_ctrl HI3660_ACLK_GATE_PCIE>; + clock-names = "pcie_phy_ref", "pcie_aux", + "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk"; + reset-gpios = <&gpio11 1 0 >; + }; diff --git a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt new file mode 100644 index 000000000000..fe80dda9bf73 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt @@ -0,0 +1,130 @@ +MediaTek Gen2 PCIe controller which is available on MT7623 series SoCs + +PCIe subsys supports single root complex (RC) with 3 Root Ports. Each root +ports supports a Gen2 1-lane Link and has PIPE interface to PHY. + +Required properties: +- compatible: Should contain "mediatek,mt7623-pcie". +- device_type: Must be "pci" +- reg: Base addresses and lengths of the PCIe controller. +- #address-cells: Address representation for root ports (must be 3) +- #size-cells: Size representation for root ports (must be 2) +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - free_ck :for reference clock of PCIe subsys + - sys_ck0 :for clock of Port0 + - sys_ck1 :for clock of Port1 + - sys_ck2 :for clock of Port2 +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pcie-rst0 :port0 reset + - pcie-rst1 :port1 reset + - pcie-rst2 :port2 reset +- phys: List of PHY specifiers (used by generic PHY framework). +- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. +- power-domains: A phandle and power domain specifier pair to the power domain + which is responsible for collapsing and restoring power to the peripheral. +- bus-range: Range of bus numbers associated with this controller. +- ranges: Ranges for the PCI memory and I/O regions. + +In addition, the device tree node must have sub-nodes describing each +PCIe port interface, having the following mandatory properties: + +Required properties: +- device_type: Must be "pci" +- reg: Only the first four bytes are used to refer to the correct bus number + and device number. +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- #interrupt-cells: Must be 1 +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- num-lanes: Number of lanes to use for this port. + +Examples: + + hifsys: syscon@1a000000 { + compatible = "mediatek,mt7623-hifsys", + "mediatek,mt2701-hifsys", + "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pcie: pcie-controller@1a140000 { + compatible = "mediatek,mt7623-pcie"; + device_type = "pci"; + reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ + <0 0x1a142000 0 0x1000>, /* Port0 registers */ + <0 0x1a143000 0 0x1000>, /* Port1 registers */ + <0 0x1a144000 0 0x1000>; /* Port2 registers */ + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 0>; + interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <&hifsys CLK_HIFSYS_PCIE0>, + <&hifsys CLK_HIFSYS_PCIE1>, + <&hifsys CLK_HIFSYS_PCIE2>; + clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2"; + resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>, + <&hifsys MT2701_HIFSYS_PCIE1_RST>, + <&hifsys MT2701_HIFSYS_PCIE2_RST>; + reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2"; + phys = <&pcie0_phy>, <&pcie1_phy>, <&pcie2_phy>; + phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>; + bus-range = <0x00 0xff>; + ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */ + 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ + + pcie@0,0 { + device_type = "pci"; + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@1,0 { + device_type = "pci"; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@2,0 { + device_type = "pci"; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index e15f9b19901f..9d418b71774f 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -8,6 +8,7 @@ - "qcom,pcie-apq8064" for apq8064 - "qcom,pcie-apq8084" for apq8084 - "qcom,pcie-msm8996" for msm8996 or apq8096 + - "qcom,pcie-ipq4019" for ipq4019 - reg: Usage: required @@ -87,7 +88,7 @@ - "core" Clocks the pcie hw block - "phy" Clocks the pcie PHY block - clock-names: - Usage: required for apq8084 + Usage: required for apq8084/ipq4019 Value type: <stringlist> Definition: Should contain the following entries - "aux" Auxiliary (AUX) clock @@ -126,6 +127,23 @@ Definition: Should contain the following entries - "core" Core reset +- reset-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "axi_m" AXI master reset + - "axi_s" AXI slave reset + - "pipe" PIPE reset + - "axi_m_vmid" VMID reset + - "axi_s_xpu" XPU reset + - "parf" PARF reset + - "phy" PHY reset + - "axi_m_sticky" AXI sticky reset + - "pipe_sticky" PIPE sticky reset + - "pwr" PWR reset + - "ahb" AHB reset + - "phy_ahb" PHY AHB reset + - power-domains: Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 34712d6fd253..bd27428dda61 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -1,4 +1,4 @@ -* Renesas RCar PCIe interface +* Renesas R-Car PCIe interface Required properties: compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; diff --git a/Documentation/devicetree/bindings/pci/tango-pcie.txt b/Documentation/devicetree/bindings/pci/tango-pcie.txt new file mode 100644 index 000000000000..244683836a79 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/tango-pcie.txt @@ -0,0 +1,29 @@ +Sigma Designs Tango PCIe controller + +Required properties: + +- compatible: "sigma,smp8759-pcie" +- reg: address/size of PCI configuration space, address/size of register area +- bus-range: defined by size of PCI configuration space +- device_type: "pci" +- #size-cells: <2> +- #address-cells: <3> +- msi-controller +- ranges: translation from system to bus addresses +- interrupts: spec for misc interrupts, spec for MSI + +Example: + + pcie@2e000 { + compatible = "sigma,smp8759-pcie"; + reg = <0x50000000 0x400000>, <0x2e000 0x100>; + bus-range = <0 3>; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + msi-controller; + ranges = <0x02000000 0x0 0x00400000 0x50400000 0x0 0x3c00000>; + interrupts = + <54 IRQ_TYPE_LEVEL_HIGH>, /* misc interrupts */ + <55 IRQ_TYPE_LEVEL_HIGH>; /* MSI */ + }; |