diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
3 files changed, 68 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index 078060a97f95..05f705e32a4a 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -18,6 +18,8 @@ Required properties for all the ethernet interfaces: - First is the Rx interrupt. This irq is mandatory. - Second is the Tx completion interrupt. This is supported only on SGMII based 1GbE and 10GbE interfaces. +- channel: Ethernet to CPU, start channel (prefetch buffer) number + - Must map to the first irq and irqs must be sequential - port-id: Port number (0 or 1) - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 28a4781ab6d7..0ae06491b430 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -45,13 +45,13 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory -- phy_id : Specifies slave phy id +- phy_id : Specifies slave phy id (deprecated, use phy-handle) - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the property phy_id, or the sub-node - fixed-link can be specified + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt new file mode 100644 index 000000000000..c421aba0a5bc --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt @@ -0,0 +1,63 @@ +Marvell 8897/8997 (sd8897/sd8997) SDIO devices +------ + +This node provides properties for controlling the marvell sdio wireless device. +The node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897" + * "marvell,sd8997" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; |