diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/stmmac.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/stmmac.txt | 54 |
1 files changed, 37 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index e862a922bd3f..6605d19601c2 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -17,7 +17,25 @@ Required properties: The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. + +Optional properties: +- resets: Should contain a phandle to the STMMAC reset signal, if any +- reset-names: Should contain the reset signal name "stmmaceth", if a + reset phandle is given +- max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property, the + first one should be "stmmaceth" and the second one should be "pclk". +- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is + available this clock is used for programming the Timestamp Addend Register. + If not passed then the system clock will be used and this is fine on some + platforms. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory - snps,pbl Programmable Burst Length +- snps,aal Address-Aligned Beats - snps,fixed-burst Program the DMA to use the fixed burst mode - snps,mixed-burst Program the DMA to use the mixed burst mode - snps,force_thresh_dma_mode Force DMA to use the threshold mode for @@ -29,27 +47,28 @@ Required properties: supported by this device instance - snps,perfect-filter-entries: Number of perfect filter entries supported by this device instance - -Optional properties: -- resets: Should contain a phandle to the STMMAC reset signal, if any -- reset-names: Should contain the reset signal name "stmmaceth", if a - reset phandle is given -- max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock - The optional second clock should be peripheral's register interface clock. - The third optional clock should be the ptp reference clock. - Further clocks may be specified in derived bindings. -- clock-names: One name for each entry in the clocks property. - The first one should be "stmmaceth". - The optional second one should be "pclk". - The optional third one should be "clk_ptp_ref". -- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. -- tx-fifo-depth: See ethernet.txt file in the same directory -- rx-fifo-depth: See ethernet.txt file in the same directory +- AXI BUS Mode parameters: below the list of all the parameters to program the + AXI register inside the DMA module: + - snps,lpi_en: enable Low Power Interface + - snps,xit_frm: unlock on WoL + - snps,wr_osr_lmt: max write oustanding req. limit + - snps,rd_osr_lmt: max read oustanding req. limit + - snps,kbbe: do not cross 1KiB boundary. + - snps,axi_all: align address + - snps,blen: this is a vector of supported burst length. + - snps,fb: fixed-burst + - snps,mb: mixed-burst + - snps,rb: rebuild INCRx Burst - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <256 128 64 32 0 0 0>; + }; + gmac0: ethernet@e0800000 { compatible = "st,spear600-gmac"; reg = <0xe0800000 0x8000>; @@ -65,6 +84,7 @@ Examples: tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; + snps,axi-config = <&stmmac_axi_setup>; mdio0 { #address-cells = <1>; #size-cells = <0>; |