diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
4 files changed, 93 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 1dd622546d06..9046ba06c47a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -12,6 +12,11 @@ Required properties: Optional properties: - fsl,cd-controller : Indicate to use controller internal card detection - fsl,wp-controller : Indicate to use controller internal write protection +- fsl,delay-line : Specify the number of delay cells for override mode. + This is used to set the clock delay for DLL(Delay Line) on override mode + to select a proper data sampling window in case the clock quality is not good + due to signal path is too long on the board. Please refer to eSDHC/uSDHC + chapter, DLL (Delay Line) section in RM for details. Examples: diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 066a78b034ca..8f3f13315358 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -52,6 +52,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. +* clock-freq-min-max: Minimum and Maximum clock frequency for card output + clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value @@ -66,6 +69,10 @@ Optional properties: * supports-highspeed: Enables support for high speed cards (up to 50MHz) +* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode + +* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode + * broken-cd: as documented in mmc core bindings. * vmmc-supply: The phandle to the regulator to use for vmmc. If this is @@ -93,8 +100,10 @@ board specific portions as listed below. dwmmc0@12200000 { clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; num-slots = <1>; supports-highspeed; + caps2-mmc-hs200-1_8v; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index ed271fc255b2..8c8908ab84ba 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed +dmas: List of DMA specifiers with the controller specific format +as described in the generic DMA client binding. A tx and rx +specifier is required. +dma-names: List of DMA request names. These strings correspond +1:1 with the DMA specifiers listed in dmas. The string naming is +to be "rx" and "tx" for RX and TX DMA requests, respectively. + +Examples: + +[hwmod populated DMA resources] + + mmc1: mmc@0x4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + ti,dual-volt; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + ti,non-removable; + }; + +[generic DMA request binding] -Example: mmc1: mmc@0x4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; @@ -30,4 +51,7 @@ Example: bus-width = <4>; vmmc-supply = <&vmmc>; /* phandle to regulator node */ ti,non-removable; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap.txt b/Documentation/devicetree/bindings/mmc/ti-omap.txt new file mode 100644 index 000000000000..8de579969763 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/ti-omap.txt @@ -0,0 +1,54 @@ +* TI MMC host controller for OMAP1 and 2420 + +The MMC Host Controller on TI OMAP1 and 2420 family provides +an interface for MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap mmc driver. + +Note that this driver will not work with omap2430 or later omaps, +please see the omap hsmmc driver for the current omaps. + +Required properties: +- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers +- ti,hwmods: For 2420, must be "msdi<n>", where n is controller + instance starting 1 + +Examples: + + msdi1: mmc@4809c000 { + compatible = "ti,omap2420-mmc"; + ti,hwmods = "msdi1"; + reg = <0x4809c000 0x80>; + interrupts = <83>; + dmas = <&sdma 61 &sdma 62>; + dma-names = "tx", "rx"; + }; + +* TI MMC host controller for OMAP1 and 2420 + +The MMC Host Controller on TI OMAP1 and 2420 family provides +an interface for MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap mmc driver. + +Note that this driver will not work with omap2430 or later omaps, +please see the omap hsmmc driver for the current omaps. + +Required properties: +- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers +- ti,hwmods: For 2420, must be "msdi<n>", where n is controller + instance starting 1 + +Examples: + + msdi1: mmc@4809c000 { + compatible = "ti,omap2420-mmc"; + ti,hwmods = "msdi1"; + reg = <0x4809c000 0x80>; + interrupts = <83>; + dmas = <&sdma 61 &sdma 62>; + dma-names = "tx", "rx"; + }; + |