diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/sdhci-st.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/sdhci-st.txt | 100 |
1 files changed, 90 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 7527db447a35..18d950df2749 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -5,20 +5,62 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the sdhci-st driver. Required properties: -- compatible : Must be "st,sdhci" -- clock-names : Should be "mmc" - See: Documentation/devicetree/bindings/resource-names.txt -- clocks : Phandle of the clock used by the sdhci controler - See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407" + to set the internal glue logic used for configuring the MMC + subsystem (mmcss) inside the FlashSS (available in STiH407 SoC + family). + +- clock-names: Should be "mmc". + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- interrupts: One mmc interrupt should be described here. +- interrupt-names: Should be "mmcirq". + +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +- reg: This must provide the host controller base address and it can also + contain the FlashSS Top register for TX/RX delay used by the driver + to configure DLL inside the flashSS, if so reg-names must also be + specified. Optional properties: -- non-removable: non-removable slot - See: Documentation/devicetree/bindings/mmc/mmc.txt -- bus-width: Number of data lines - See: Documentation/devicetree/bindings/mmc/mmc.txt +- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional + for eMMC on stih407 family silicon to configure DLL inside FlashSS. + +- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC + family. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- bus-width: Number of data lines. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for + configuring the CCONFIG3 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- resets: Phandle and reset specifier pair to softreset line of HC IP. + See: Documentation/devicetree/bindings/reset/reset.txt + +- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd + supply in eMMC/SD specs. + +- sd-uhs--sdr50: To enable the SDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-sdr104: To enable the SDR104 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-ddr50: To enable the DDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. Example: +/* Example stih416e eMMC configuration */ + mmc0: sdhci@fe81e000 { compatible = "st,sdhci"; status = "disabled"; @@ -29,5 +71,43 @@ mmc0: sdhci@fe81e000 { pinctrl-0 = <&pinctrl_mmc0>; clock-names = "mmc"; clocks = <&clk_s_a1_ls 1>; - bus-width = <8> + bus-width = <8> + +/* Example SD stih407 family configuration */ + +mmc1: sdhci@09080000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09080000 0x7ff>; + reg-names = "mmc"; + interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd1>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_1>; + resets = <&softreset STIH407_MMC1_SOFTRESET>; + bus-width = <4>; +}; + +/* Example eMMC stih407 family configuration */ + +mmc0: sdhci@09060000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09060000 0x7ff>, <0x9061008 0x20>; + reg-names = "mmc", "top-mmc-delay"; + interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_0>; + vqmmc-supply = <&vmmc_reg>; + max-frequency = <200000000>; + bus-width = <8>; + non-removable; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; }; |