diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input/touchscreen')
4 files changed, 185 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt new file mode 100644 index 000000000000..e3f22d23fc8f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -0,0 +1,53 @@ +* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) + +Required properties: +- compatible : for SPI slave, use "adi,ad7879" + for I2C slave, use "adi,ad7879-1" +- reg : SPI chipselect/I2C slave address + See spi-bus.txt for more SPI slave properties +- interrupt-parent : the phandle for the interrupt controller +- interrupts : touch controller interrupt +- touchscreen-max-pressure : maximum reported pressure +- adi,resistance-plate-x : total resistance of X-plate (for pressure + calculation) +Optional properties: +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) +- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) + 13 : 2.560ms + 14 : 3.584ms + 15 : 4.096ms + This property has to be a '/bits/ 8' value +- adi,acquisition-time : 0: 2us + 1: 4us + 2: 8us + 3: 16us + This property has to be a '/bits/ 8' value +- adi,median-filter-size : 0: disabled + 1: 4 measurements + 2: 8 measurements + 3: 16 measurements + This property has to be a '/bits/ 8' value +- adi,averaging : 0: 2 middle values (1 if median disabled) + 1: 4 middle values + 2: 8 middle values + 3: 16 values + This property has to be a '/bits/ 8' value +- adi,conversion-interval: : 0 : convert one time only + 1-255: 515us + val * 35us (up to 9.440ms) + This property has to be a '/bits/ 8' value + +Example: + + ad7879@2c { + compatible = "adi,ad7879-1"; + reg = <0x2c>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt new file mode 100644 index 000000000000..b75d4cfd2c36 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt @@ -0,0 +1,95 @@ +* Cypress cyttsp touchscreen controller + +Required properties: + - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi" + - reg : Device I2C address or SPI chip select number + - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi) + - interrupt-parent : the phandle for the gpio controller + (see interrupt binding[0]). + - interrupts : (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). + - bootloader-key : the 8-byte bootloader key that is required to switch + the chip from bootloader mode (default mode) to + application mode. + This property has to be specified as an array of 8 + '/bits/ 8' values. + +Optional properties: + - reset-gpios : the reset gpio the chip is connected to + (see GPIO binding[1] for more details). + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-fuzz-x : horizontal noise value of the absolute input device + (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input device + (in pixels) + - active-distance : the distance in pixels beyond which a touch must move + before movement is detected and reported by the device. + Valid values: 0-15. + - active-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in active mode. + Valid values: 0-255. + - lowpower-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in low-power mode. + Valid values: 0-2550 + - touch-timeout-ms : minimum time in ms spent in the active power state while no + touches are detected before entering low-power mode. + Valid values: 0-2550 + - use-handshake : enable register-based handshake (boolean). This should + only be used if the chip is configured to use 'blocking + communication with timeout' (in this case the device + generates an interrupt at the end of every + scanning/processing cycle). + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + cyttsp@a { + compatible = "cypress,cyttsp-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; + + &mcspi1 { + /* ... */ + cyttsp@0 { + compatible = "cypress,cyttsp-spi"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt new file mode 100644 index 000000000000..cdf05f9b2329 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -0,0 +1,35 @@ +Freescale mx25 TS conversion queue module + +mx25 touchscreen conversion queue module which controls the ADC unit of the +mx25 for attached touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tcq". + - reg: Memory range of the device. + - interrupts: Should be the interrupt number associated with this module within + the tscadc unit (<0>). + - interrupt-parent: Should be a phandle to the tscadc unit. + - fsl,wires: Should be '<4>' or '<5>' + +Optional properties: + - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. + - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value + between 1 and 4096. It is the ratio between the internal reference voltage + and the measured voltage after the plate was precharged. Resistence between + plates and therefore the voltage decreases with pressure so that a smaller + value is equivalent to a higher pressure. + - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before + the actual touch detection to wait for an even charge distribution in the + plate. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + interrupt-parent = <&tscadc>; + interrupts = <0>; + fsl,wires = <4>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt index ac23caf518ad..bccaa4e73045 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -18,6 +18,8 @@ Optional properties for Touchscreens: - touchscreen-inverted-y : Y axis is inverted (boolean) - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) Swapping is done after inverting the axis + - touchscreen-x-mm : horizontal length in mm of the touchscreen + - touchscreen-y-mm : vertical length in mm of the touchscreen Deprecated properties for Touchscreens: - x-size : deprecated name for touchscreen-size-x |