diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display')
114 files changed, 5216 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt new file mode 100644 index 000000000000..3e3039a8a253 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -0,0 +1,109 @@ +* ARM PrimeCell Color LCD Controller PL110/PL111 + +See also Documentation/devicetree/bindings/arm/primecell.txt + +Required properties: + +- compatible: must be one of: + "arm,pl110", "arm,primecell" + "arm,pl111", "arm,primecell" + +- reg: base address and size of the control registers block + +- interrupt-names: either the single entry "combined" representing a + combined interrupt output (CLCDINTR), or the four entries + "mbe", "vcomp", "lnbu", "fuf" representing the individual + CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts + +- interrupts: contains an interrupt specifier for each entry in + interrupt-names + +- clock-names: should contain "clcdclk" and "apb_pclk" + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/binding/clock/clock-bindings.txt + +Optional properties: + +- memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer + may be located anywhere in the memory + +- max-memory-bandwidth: maximum bandwidth in bytes per second that the + cell's memory interface can handle; if not present, the memory + interface is fast enough to handle all possible video modes + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt; + when it is a TFT panel, the port's endpoint must define the + following property: + + - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values, + defining the way CLD pads are wired up; first value + contains index of the "CLD" external pin (pad) used + as R0 (first bit of the red component), second value + index of the pad used as G0, third value index of the + pad used as B0, see also "LCD panel signal multiplexing + details" paragraphs in the PL110/PL111 Technical + Reference Manuals; this implicitly defines available + color modes, for example: + - PL111 TFT 4:4:4 panel: + arm,pl11x,tft-r0g0b0-pads = <4 15 20>; + - PL110 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <1 7 13>; + - PL111 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 11 19>; + - PL111 TFT 5:6:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 10 19>; + - PL110 and PL111 TFT 8:8:8 panel: + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped: + arm,pl11x,tft-r0g0b0-pads = <16 8 0>; + + +Example: + + clcd@10020000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x10020000 0x1000>; + interrupt-names = "combined"; + interrupts = <0 44 4>; + clocks = <&oscclk1>, <&oscclk2>; + clock-names = "clcdclk", "apb_pclk"; + max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */ + + port { + clcd_pads: endpoint { + remote-endpoint = <&clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; + + }; + + panel { + compatible = "panel-dpi"; + + port { + clcd_panel: endpoint { + remote-endpoint = <&clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <25175000>; + hactive = <640>; + hback-porch = <40>; + hfront-porch = <24>; + hsync-len = <96>; + vactive = <480>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/armada/marvell,dove-lcd.txt b/Documentation/devicetree/bindings/display/armada/marvell,dove-lcd.txt new file mode 100644 index 000000000000..46525ea3e646 --- /dev/null +++ b/Documentation/devicetree/bindings/display/armada/marvell,dove-lcd.txt @@ -0,0 +1,30 @@ +Device Tree bindings for Armada DRM CRTC driver + +Required properties: + - compatible: value should be "marvell,dove-lcd". + - reg: base address and size of the LCD controller + - interrupts: single interrupt number for the LCD controller + - port: video output port with endpoints, as described by graph.txt + +Optional properties: + + - clocks: as described by clock-bindings.txt + - clock-names: as described by clock-bindings.txt + "axiclk" - axi bus clock for pixel clock + "plldivider" - pll divider clock for pixel clock + "ext_ref_clk0" - external clock 0 for pixel clock + "ext_ref_clk1" - external clock 1 for pixel clock + +Note: all clocks are optional but at least one must be specified. +Further clocks may be added in the future according to requirements of +different SoCs. + +Example: + + lcd0: lcd-controller@820000 { + compatible = "marvell,dove-lcd"; + reg = <0x820000 0x1000>; + interrupts = <47>; + clocks = <&si5351 0>; + clock-names = "ext_ref_clk_1"; + }; diff --git a/Documentation/devicetree/bindings/display/atmel,lcdc.txt b/Documentation/devicetree/bindings/display/atmel,lcdc.txt new file mode 100644 index 000000000000..ecb8da063d07 --- /dev/null +++ b/Documentation/devicetree/bindings/display/atmel,lcdc.txt @@ -0,0 +1,89 @@ +Atmel LCDC Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : + "atmel,at91sam9261-lcdc" , + "atmel,at91sam9263-lcdc" , + "atmel,at91sam9g10-lcdc" , + "atmel,at91sam9g45-lcdc" , + "atmel,at91sam9g45es-lcdc" , + "atmel,at91sam9rl-lcdc" , + "atmel,at32ap-lcdc" +- reg : Should contain 1 register ranges(address and length). + Can contain an additional register range(address and length) + for fixed framebuffer memory. Useful for dedicated memories. +- interrupts : framebuffer controller interrupt +- display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. +- default-mode: a videomode within the display with timing parameters + as specified below. + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + +Example: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9g45-lcdc"; + reg = <0x00500000 0x1000>; + interrupts = <23 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + display = <&display0>; + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + }; + +Example for fixed framebuffer memory: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9263-lcdc"; + reg = <0x00700000 0x1000 0x70000000 0x200000>; + [...] + }; + +Atmel LCDC Display +----------------------------------------------------- +Required properties (as per of_videomode_helper): + + - atmel,dmacon: dma controller configuration + - atmel,lcdcon2: lcd controller configuration + - atmel,guard-time: lcd guard time (Delay in frame periods) + - bits-per-pixel: lcd panel bit-depth. + +Optional properties (as per of_videomode_helper): + - atmel,lcdcon-backlight: enable backlight + - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG" + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed) + +Example: + display0: display { + bits-per-pixel = <32>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <9>; + atmel,lcd-wiring-mode = <1>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hback-porch = <1>; + hfront-porch = <1>; + vback-porch = <40>; + vfront-porch = <1>; + hsync-len = <45>; + vsync-len = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt new file mode 100644 index 000000000000..ebc1a914bda3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt @@ -0,0 +1,53 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver + +The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device. +See ../mfd/atmel-hlcdc.txt for more details. + +Required properties: + - compatible: value should be "atmel,hlcdc-display-controller" + - pinctrl-names: the pin control state names. Should contain "default". + - pinctrl-0: should contain the default pinctrl states. + - #address-cells: should be set to 1. + - #size-cells: should be set to 0. + +Required children nodes: + Children nodes are encoding available output ports and their connections + to external devices using the OF graph reprensentation (see ../graph.txt). + At least one port node is required. + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt new file mode 100644 index 000000000000..a6b2b2b8f3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt @@ -0,0 +1,50 @@ +Analog Device ADV7123 Video DAC +------------------------------- + +The ADV7123 is a digital-to-analog converter that outputs VGA signals from a +parallel video input. + +Required properties: + +- compatible: Should be "adi,adv7123" + +Optional properties: + +- psave-gpios: Power save control GPIO + +Required nodes: + +The ADV7123 has two video ports. Their connections are modeled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DPI input +- Video port 1 for VGA output + + +Example +------- + + adv7123: encoder@0 { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7123_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7123_out: endpoint@0 { + remote-endpoint = <&vga_connector_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt new file mode 100644 index 000000000000..96c25ee01501 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -0,0 +1,88 @@ +Analog Device ADV7511(W)/13 HDMI Encoders +----------------------------------------- + +The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, +S/PDIF, CEC and HDCP. + +Required properties: + +- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- reg: I2C slave address + +The ADV7511 supports a large number of input data formats that differ by their +color depth, color format, clock mode, bit justification and random +arrangement of components on the data bus. The combination of the following +properties describe the input and map directly to the video input tables of the +ADV7511 datasheet that document all the supported combinations. + +- adi,input-depth: Number of bits per color component at the input (8, 10 or + 12). +- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or + "yuv444". +- adi,input-clock: The input clock type, one of "1x" (one clock cycle per + pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel, + data driven on both edges). + +The following input format properties are required except in "rgb 1x" and +"yuv444 1x" modes, in which case they must not be specified. + +- adi,input-style: The input components arrangement variant (1, 2 or 3), as + listed in the input format tables in the datasheet. +- adi,input-justification: The input bit justification ("left", "evenly", + "right"). + +Optional properties: + +- interrupts: Specifier for the ADV7511 interrupt +- pd-gpios: Specifier for the GPIO connected to the power down signal + +- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps + (-1200 ps .. 1600 ps). Defaults to no delay. +- adi,embedded-sync: The input uses synchronization signals embedded in the + data stream (similar to BT.656). Defaults to separate H/V synchronization + signals. + +Required nodes: + +The ADV7511 has two video ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for the RGB or YUV input +- Video port 1 for the HDMI output + + +Example +------- + + adv7511w: hdmi@39 { + compatible = "adi,adv7511w"; + reg = <39>; + interrupt-parent = <&gpio3>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511w_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt new file mode 100644 index 000000000000..dc1452f0d5d8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt @@ -0,0 +1,50 @@ +DesignWare HDMI bridge bindings + +Required properties: +- compatible: platform specific such as: + * "snps,dw-hdmi-tx" + * "fsl,imx6q-hdmi" + * "fsl,imx6dl-hdmi" + * "rockchip,rk3288-dw-hdmi" +- reg: Physical base address and length of the controller's registers. +- interrupts: The HDMI interrupt number +- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, + as described in Documentation/devicetree/bindings/clock/clock-bindings.txt, + the clocks are soc specific, the clock-names should be "iahb", "isfr" +-port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/display/imx/hdmi.txt + * Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt + +Optional properties +- reg-io-width: the width of the reg:1,4, default set to 1 if not present +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" + +Example: + hdmi: hdmi@0120000 { + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/ps8622.txt b/Documentation/devicetree/bindings/display/bridge/ps8622.txt new file mode 100644 index 000000000000..c989c3807f2b --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ps8622.txt @@ -0,0 +1,31 @@ +ps8622-bridge bindings + +Required properties: + - compatible: "parade,ps8622" or "parade,ps8625" + - reg: first i2c address of the bridge + - sleep-gpios: OF device-tree gpio specification for PD_ pin. + - reset-gpios: OF device-tree gpio specification for RST_ pin. + +Optional properties: + - lane-count: number of DP lanes to use + - use-external-pwm: backlight will be controlled by an external PWM + - video interfaces: Device node can contain video interface port + nodes for panel according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + lvds-bridge@48 { + compatible = "parade,ps8622"; + reg = <0x48>; + sleep-gpios = <&gpc3 6 1 0 0>; + reset-gpios = <&gpc3 1 1 0 0>; + lane-count = <1>; + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/ptn3460.txt b/Documentation/devicetree/bindings/display/bridge/ptn3460.txt new file mode 100644 index 000000000000..361971ba104d --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ptn3460.txt @@ -0,0 +1,39 @@ +ptn3460 bridge bindings + +Required properties: + - compatible: "nxp,ptn3460" + - reg: i2c address of the bridge + - powerdown-gpio: OF device-tree gpio specification for PD_N pin. + - reset-gpio: OF device-tree gpio specification for RST_N pin. + - edid-emulation: The EDID emulation entry to use + +-------+------------+------------------+ + | Value | Resolution | Description | + | 0 | 1024x768 | NXP Generic | + | 1 | 1920x1080 | NXP Generic | + | 2 | 1920x1080 | NXP Generic | + | 3 | 1600x900 | Samsung LTM200KT | + | 4 | 1920x1080 | Samsung LTM230HT | + | 5 | 1366x768 | NXP Generic | + | 6 | 1600x900 | ChiMei M215HGE | + +-------+------------+------------------+ + + - video interfaces: Device node can contain video interface port + nodes for panel according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpio = <&gpy2 5 1 0 0>; + reset-gpio = <&gpx1 5 1 0 0>; + edid-emulation = <5>; + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt new file mode 100644 index 000000000000..e9e4bce40760 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for the NXP TDA998x HDMI transmitter + +Required properties; + - compatible: must be "nxp,tda998x" + + - reg: I2C address + +Optional properties: + - interrupts: interrupt number and trigger type + default: polling + + - pinctrl-0: pin control group to be used for + screen plug/unplug interrupt. + + - pinctrl-names: must contain a "default" entry. + + - video-ports: 24 bits value which defines how the video controller + output is wired to the TDA998x input - default: <0x230145> + +Example: + + tda998x: hdmi-encoder { + compatible = "nxp,tda998x"; + reg = <0x70>; + interrupt-parent = <&gpio0>; + interrupts = <27 2>; /* falling edge */ + pinctrl-0 = <&pmx_camera>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt new file mode 100644 index 000000000000..527e236e9a2a --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt @@ -0,0 +1,50 @@ +THine Electronics THC63LVDM83D LVDS serializer +---------------------------------------------- + +The THC63LVDM83D is an LVDS serializer designed to support pixel data +transmission between a host and a flat panel. + +Required properties: + +- compatible: Should be "thine,thc63lvdm83d" + +Optional properties: + +- pwdn-gpios: Power down control GPIO + +Required nodes: + +The THC63LVDM83D has two video ports. Their connections are modeled using the +OFgraph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for CMOS/TTL input +- Video port 1 for LVDS output + + +Example +------- + + lvds_enc: encoder@0 { + compatible = "thine,thc63lvdm83d"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_enc_in: endpoint@0 { + remote-endpoint = <&rgb_out>; + }; + }; + + port@1 { + reg = <1>; + + lvds_enc_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt new file mode 100644 index 000000000000..d685be898d0c --- /dev/null +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -0,0 +1,47 @@ +* Currus Logic CLPS711X Framebuffer + +Required properties: +- compatible: Shall contain "cirrus,clps711x-fb". +- reg : Physical base address and length of the controller's registers + + location and size of the framebuffer memory. +- clocks : phandle + clock specifier pair of the FB reference clock. +- display : phandle to a display node as described in + Documentation/devicetree/bindings/display/display-timing.txt. + Additionally, the display node has to define properties: + - bits-per-pixel: Bits per pixel. + - ac-prescale : LCD AC bias frequency. This frequency is the required + AC bias frequency for a given manufacturer's LCD plate. + - cmap-invert : Invert the color levels (Optional). + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + +Example: + fb: fb@800002c0 { + compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; + clocks = <&clks 2>; + lcd-supply = <®5v0>; + display = <&display>; + }; + + display: display { + model = "320x240x4"; + native-mode = <&timing0>; + bits-per-pixel = <4>; + ac-prescale = <17>; + + display-timings { + timing0: 320x240 { + hactive = <320>; + hback-porch = <0>; + hfront-porch = <0>; + hsync-len = <0>; + vactive = <240>; + vback-porch = <0>; + vfront-porch = <0>; + vsync-len = <0>; + clock-frequency = <6500000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt b/Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt new file mode 100644 index 000000000000..0c0970c210ab --- /dev/null +++ b/Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt @@ -0,0 +1,25 @@ +Analog TV Connector +=================== + +Required properties: +- compatible: "composite-video-connector" or "svideo-connector" + +Optional properties: +- label: a symbolic name for the connector + +Required nodes: +- Video port for TV input + +Example +------- + +tv: connector { + compatible = "composite-video-connector"; + label = "tv"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&venc_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/connector/dvi-connector.txt b/Documentation/devicetree/bindings/display/connector/dvi-connector.txt new file mode 100644 index 000000000000..fc53f7c60bc6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/connector/dvi-connector.txt @@ -0,0 +1,35 @@ +DVI Connector +============== + +Required properties: +- compatible: "dvi-connector" + +Optional properties: +- label: a symbolic name for the connector +- ddc-i2c-bus: phandle to the i2c bus that is connected to DVI DDC +- analog: the connector has DVI analog pins +- digital: the connector has DVI digital pins +- dual-link: the connector has pins for DVI dual-link + +Required nodes: +- Video port for DVI input + +Note: One (or both) of 'analog' or 'digital' must be set. + +Example +------- + +dvi0: connector@0 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c3>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt new file mode 100644 index 000000000000..acd5668b1ce1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt @@ -0,0 +1,29 @@ +HDMI Connector +============== + +Required properties: +- compatible: "hdmi-connector" +- type: the HDMI connector type: "a", "b", "c", "d" or "e" + +Optional properties: +- label: a symbolic name for the connector +- hpd-gpios: HPD GPIO number + +Required nodes: +- Video port for HDMI input + +Example +------- + +hdmi0: connector@1 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/connector/vga-connector.txt b/Documentation/devicetree/bindings/display/connector/vga-connector.txt new file mode 100644 index 000000000000..c727f298e7ad --- /dev/null +++ b/Documentation/devicetree/bindings/display/connector/vga-connector.txt @@ -0,0 +1,36 @@ +VGA Connector +============= + +Required properties: + +- compatible: "vga-connector" + +Optional properties: + +- label: a symbolic name for the connector corresponding to a hardware label +- ddc-i2c-bus: phandle to the I2C bus that is connected to VGA DDC + +Required nodes: + +The VGA connector internal connections are modeled using the OF graph bindings +specified in Documentation/devicetree/bindings/graph.txt. + +The VGA connector has a single port that must be connected to a video source +port. + + +Example +------- + +vga0: connector@0 { + compatible = "vga-connector"; + label = "vga"; + + ddc-i2c-bus = <&i2c3>; + + port { + vga_connector_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt b/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt new file mode 100644 index 000000000000..0fba2ee6440a --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos-mic.txt @@ -0,0 +1,51 @@ +Device-Tree bindings for Samsung Exynos SoC mobile image compressor (MIC) + +MIC (mobile image compressor) resides between decon and mipi dsi. Mipi dsi is +not capable to transfer high resoltuion frame data as decon can send. MIC +solves this problem by compressing the frame data by 1/2 before it is +transferred through mipi dsi. The compressed frame data must be uncompressed in +the panel PCB. + +Required properties: +- compatible: value should be "samsung,exynos5433-mic". +- reg: physical base address and length of the MIC registers set and system + register of mic. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "pclk_mic0", "sclk_rgb_vclk_to_mic0". +- samsung,disp-syscon: the reference node for syscon for DISP block. +- ports: contains a port which is connected to decon node and dsi node. + address-cells and size-cells must 1 and 0, respectively. +- port: contains an endpoint node which is connected to the endpoint in the + decon node or dsi node. The reg value must be 0 and 1 respectively. + +Example: +SoC specific DT entry: +mic: mic@13930000 { + compatible = "samsung,exynos5433-mic"; + reg = <0x13930000 0x48>; + clocks = <&cmu_disp CLK_PCLK_MIC0>, + <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>; + clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0"; + samsung,disp-syscon = <&syscon_disp>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mic_to_decon: endpoint { + remote-endpoint = <&decon_to_mic>; + }; + }; + + port@1 { + reg = <1>; + mic_to_dsi: endpoint { + remote-endpoint = <&dsi_to_mic>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt new file mode 100644 index 000000000000..377afbf5122a --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -0,0 +1,65 @@ +Device-Tree bindings for Samsung Exynos SoC display controller (DECON) + +DECON (Display and Enhancement Controller) is the Display Controller for the +Exynos series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be "samsung,exynos5433-decon"; +- reg: physical base address and length of the DECON registers set. +- interrupts: should contain a list of all DECON IP block interrupts in the + order: VSYNC, LCD_SYSTEM. The interrupt specifier format + depends on the interrupt controller used. +- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys" + in the same order as they were listed in the interrupts + property. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "aclk_decon", "aclk_smmu_decon0x", + "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", + "sclk_decon_eclk" +- ports: contains a port which is connected to mic node. address-cells and + size-cells must 1 and 0, respectively. +- port: contains an endpoint node which is connected to the endpoint in the mic + node. The reg value muset be 0. +- i80-if-timings: specify whether the panel which is connected to decon uses + i80 lcd interface or mipi video interface. This node contains + no timing information as that of fimd does. Because there is + no register in decon to specify i80 interface timing value, + it is not needed, but make it remain to use same kind of node + in fimd and exynos7 decon. + +Example: +SoC specific DT entry: +decon: decon@13800000 { + compatible = "samsung,exynos5433-decon"; + reg = <0x13800000 0x2104>; + clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>, + <&cmu_disp CLK_ACLK_XIU_DECON0X>, + <&cmu_disp CLK_PCLK_SMMU_DECON0X>, + <&cmu_disp CLK_SCLK_DECON_VCLK>, + <&cmu_disp CLK_SCLK_DECON_ECLK>; + clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", + "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk"; + interrupt-names = "vsync", "lcd_sys"; + interrupts = <0 202 0>, <0 203 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + decon_to_mic: endpoint { + remote-endpoint = <&mic_to_decon>; + }; + }; + }; +}; + +Board specific DT entry: +&decon { + i80-if-timings { + }; +}; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt new file mode 100644 index 000000000000..3938caacf11c --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt @@ -0,0 +1,68 @@ +Device-Tree bindings for Samsung Exynos7 SoC display controller (DECON) + +DECON (Display and Enhancement Controller) is the Display Controller for the +Exynos7 series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be "samsung,exynos7-decon"; + +- reg: physical base address and length of the DECON registers set. + +- interrupt-parent: should be the phandle of the decon controller's + parent interrupt controller. + +- interrupts: should contain a list of all DECON IP block interrupts in the + order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- interrupt-names: should contain the interrupt names: "fifo", "vsync", + "lcd_sys", in the same order as they were listed in the interrupts + property. + +- pinctrl-0: pin control group to be used for this controller. + +- pinctrl-names: must contain a "default" entry. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "pclk_decon0", "aclk_decon0", + "decon0_eclk", "decon0_vclk". +- i80-if-timings: timing configuration for lcd i80 interface support. + +Optional Properties: +- samsung,power-domain: a phandle to DECON power domain node. +- display-timings: timing settings for DECON, as described in document [1]. + Can be used in case timings cannot be provided otherwise + or to override timings provided by the panel. + +[1]: Documentation/devicetree/bindings/display/display-timing.txt + +Example: + +SoC specific DT entry: + + decon@13930000 { + compatible = "samsung,exynos7-decon"; + interrupt-parent = <&combiner>; + reg = <0x13930000 0x1000>; + interrupt-names = "lcd_sys", "vsync", "fifo"; + interrupts = <0 188 0>, <0 189 0>, <0 190 0>; + clocks = <&clock_disp PCLK_DECON_INT>, + <&clock_disp ACLK_DECON_INT>, + <&clock_disp SCLK_DECON_INT_ECLK>, + <&clock_disp SCLK_DECON_INT_EXTCLKPLL>; + clock-names = "pclk_decon0", "aclk_decon0", "decon0_eclk", + "decon0_vclk"; + status = "disabled"; + }; + +Board specific DT entry: + + decon@13930000 { + pinctrl-0 = <&lcd_clk &pwm1_out>; + pinctrl-names = "default"; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt new file mode 100644 index 000000000000..64693f2ebc51 --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -0,0 +1,120 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: deprecated, use phys and phy-names + -reg: deprecated + Base address of DP PHY register. + -samsung,enable-mask: deprecated + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -interrupt-parent: + phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + -samsung,color-space: + input video data format. + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + -samsung,dynamic-range: + dynamic range for input video data. + VESA = 0, CEA = 1 + -samsung,ycbcr-coeff: + YCbCr co-efficients for input video. + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + -samsung,color-depth: + number of bits per colour component. + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + -samsung,link-rate: + link rate supported by the panel. + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A + -samsung,lane-count: + number of lanes supported by the panel. + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/display-timing.txt + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + -samsung,hpd-gpio: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug + detection + -video interfaces: Device node can contain video interface port + nodes according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; + +Board Specific portion: + dp-controller { + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <4>; + + display-timings { + native-mode = <&lcd_timing>; + lcd_timing: 1366x768 { + clock-frequency = <70589280>; + hactive = <1366>; + vactive = <768>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <32>; + vback-porch = <10>; + vfront-porch = <12>; + vsync-len = <6>; + }; + }; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt new file mode 100644 index 000000000000..0e6f0c024858 --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -0,0 +1,103 @@ +Exynos MIPI DSI Master + +Required properties: + - compatible: value should be one of the following + "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ + "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ + "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ + "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ + "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ + - reg: physical base address and length of the registers set for the device + - interrupts: should contain DSI interrupt + - clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names + - clock-names: should include "bus_clk"and "sclk_mipi" entries + the use of "pll_clk" is deprecated + - phys: list of phy specifiers, must contain an entry for each required + entry in phy-names + - phy-names: should include "dsim" entry + - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V) + - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V) + - samsung,pll-clock-frequency: specifies frequency of the oscillator clock + - #address-cells, #size-cells: should be set respectively to <1> and <0> + according to DSI host bindings (see MIPI DSI bindings [1]) + +Optional properties: + - power-domains: a phandle to DSIM power domain node + +Child nodes: + Should contain DSI peripheral nodes (see MIPI DSI bindings [1]). + +Video interfaces: + Device node can contain video interface port nodes according to [2]. + The following are properties specific to those nodes: + + port node inbound: + - reg: (required) must be 0. + port node outbound: + - reg: (required) must be 1. + + endpoint node connected from mic node (reg = 0): + - remote-endpoint: specifies the endpoint in mic node. This node is required + for Exynos5433 mipi dsi. So mic can access to panel node + thoughout this dsi node. + endpoint node connected to panel node (reg = 1): + - remote-endpoint: specifies the endpoint in panel node. This node is + required in all kinds of exynos mipi dsi to represent + the connection between mipi dsi and panel. + - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst + mode + - samsung,esc-clock-frequency: specifies DSI frequency in escape mode + +[1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + dsi@11C80000 { + compatible = "samsung,exynos4210-mipi-dsi"; + reg = <0x11C80000 0x10000>; + interrupts = <0 79 0>; + clocks = <&clock 286>, <&clock 143>; + clock-names = "bus_clk", "sclk_mipi"; + phys = <&mipi_phy 1>; + phy-names = "dsim"; + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + power-domains = <&pd_lcd0>; + #address-cells = <1>; + #size-cells = <0>; + samsung,pll-clock-frequency = <24000000>; + + panel@1 { + reg = <0>; + ... + port { + panel_ep: endpoint { + remote-endpoint = <&dsi_ep>; + }; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + decon_to_mic: endpoint { + remote-endpoint = <&mic_to_decon>; + }; + }; + + port@1 { + reg = <1>; + dsi_ep: endpoint { + reg = <0>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + remote-endpoint = <&panel_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt new file mode 100644 index 000000000000..1fd8cf9cbfac --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -0,0 +1,43 @@ +Device-Tree bindings for drm hdmi driver + +Required properties: +- compatible: value should be one among the following: + 1) "samsung,exynos5-hdmi" <DEPRECATED> + 2) "samsung,exynos4210-hdmi" + 3) "samsung,exynos4212-hdmi" + 4) "samsung,exynos5420-hdmi" +- reg: physical base address of the hdmi and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- hpd-gpio: following information about the hotplug gpio pin. + a) phandle of the gpio controller node. + b) pin number within the gpio controller. + c) optional flags and pull up/down. +- clocks: list of clock IDs from SoC clock driver. + a) hdmi: Gate of HDMI IP bus clock. + b) sclk_hdmi: Gate of HDMI special clock. + c) sclk_pixel: Pixel special clock, one of the two possible inputs of + HDMI clock mux. + d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of + HDMI clock mux. + e) mout_hdmi: It is required by the driver to switch between the 2 + parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable + after configuration, parent is set to sclk_hdmiphy else + sclk_pixel. +- clock-names: aliases as per driver requirements for above clock IDs: + "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + +Example: + + hdmi { + compatible = "samsung,exynos4212-hdmi"; + reg = <0x14530000 0x100000>; + interrupts = <0 95 0>; + hpd-gpio = <&gpx3 7 1>; + ddc = <&hdmi_ddc_node>; + phy = <&hdmi_phy_node>; + samsung,syscon-phandle = <&pmu_system_controller>; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt new file mode 100644 index 000000000000..41eee971562b --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiddc.txt @@ -0,0 +1,15 @@ +Device-Tree bindings for hdmiddc driver + +Required properties: +- compatible: value should be one of the following + 1) "samsung,exynos5-hdmiddc" <DEPRECATED> + 2) "samsung,exynos4210-hdmiddc" + +- reg: I2C address of the hdmiddc device. + +Example: + + hdmiddc { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt new file mode 100644 index 000000000000..162f641f7639 --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmiphy.txt @@ -0,0 +1,15 @@ +Device-Tree bindings for hdmiphy driver + +Required properties: +- compatible: value should be one of the following: + 1) "samsung,exynos5-hdmiphy" <DEPRECATED> + 2) "samsung,exynos4210-hdmiphy". + 3) "samsung,exynos4212-hdmiphy". +- reg: I2C address of the hdmiphy device. + +Example: + + hdmiphy { + compatible = "samsung,exynos4210-hdmiphy"; + reg = <0x38>; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt b/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt new file mode 100644 index 000000000000..3e38128f866b --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_mixer.txt @@ -0,0 +1,26 @@ +Device-Tree bindings for mixer driver + +Required properties: +- compatible: value should be one of the following: + 1) "samsung,exynos5-mixer" <DEPRECATED> + 2) "samsung,exynos4210-mixer" + 3) "samsung,exynos4212-mixer" + 4) "samsung,exynos5250-mixer" + 5) "samsung,exynos5420-mixer" + +- reg: physical base address of the mixer and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- clocks: list of clock IDs from SoC clock driver. + a) mixer: Gate of Mixer IP bus clock. + b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of + mixer mux. + c) hdmi: Gate of HDMI IP bus clock, needed together with sclk_hdmi. + +Example: + + mixer { + compatible = "samsung,exynos5250-mixer"; + reg = <0x14450000 0x10000>; + interrupts = <0 94 0>; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt new file mode 100644 index 000000000000..27c3ce0db16a --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -0,0 +1,110 @@ +Device-Tree bindings for Samsung SoC display controller (FIMD) + +FIMD (Fully Interactive Mobile Display) is the Display Controller for the +Samsung series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be one of the following + "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ + "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ + "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ + "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ + "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ + "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ + "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ + +- reg: physical base address and length of the FIMD registers set. + +- interrupt-parent: should be the phandle of the fimd controller's + parent interrupt controller. + +- interrupts: should contain a list of all FIMD IP block interrupts in the + order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- interrupt-names: should contain the interrupt names: "fifo", "vsync", + "lcd_sys", in the same order as they were listed in the interrupts + property. + +- pinctrl-0: pin control group to be used for this controller. + +- pinctrl-names: must contain a "default" entry. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "sclk_fimd" and "fimd". + +Optional Properties: +- power-domains: a phandle to FIMD power domain node. +- samsung,invert-vden: video enable signal is inverted +- samsung,invert-vclk: video clock signal is inverted +- display-timings: timing settings for FIMD, as described in document [1]. + Can be used in case timings cannot be provided otherwise + or to override timings provided by the panel. +- samsung,sysreg: handle to syscon used to control the system registers +- i80-if-timings: timing configuration for lcd i80 interface support. + - cs-setup: clock cycles for the active period of address signal is enabled + until chip select is enabled. + If not specified, the default value(0) will be used. + - wr-setup: clock cycles for the active period of CS signal is enabled until + write signal is enabled. + If not specified, the default value(0) will be used. + - wr-active: clock cycles for the active period of CS is enabled. + If not specified, the default value(1) will be used. + - wr-hold: clock cycles for the active period of CS is disabled until write + signal is disabled. + If not specified, the default value(0) will be used. + + The parameters are defined as: + + VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|?? + : : : : : + Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX + | cs-setup+1 | : : : + |<---------->| : : : + Chip Select ???????????????|____________:____________:____________|?? + | wr-setup+1 | | wr-hold+1 | + |<---------->| |<---------->| + Write Enable ????????????????????????????|____________|??????????????? + | wr-active+1| + |<---------->| + Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>-- + +The device node can contain 'port' child nodes according to the bindings defined +in [2]. The following are properties specific to those nodes: +- reg: (required) port index, can be: + 0 - for CAMIF0 input, + 1 - for CAMIF1 input, + 2 - for CAMIF2 input, + 3 - for parallel output, + 4 - for write-back interface + +[1]: Documentation/devicetree/bindings/display/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + +SoC specific DT entry: + + fimd@11c00000 { + compatible = "samsung,exynos4210-fimd"; + interrupt-parent = <&combiner>; + reg = <0x11c00000 0x20000>; + interrupt-names = "fifo", "vsync", "lcd_sys"; + interrupts = <11 0>, <11 1>, <11 2>; + clocks = <&clock 140>, <&clock 283>; + clock-names = "sclk_fimd", "fimd"; + power-domains = <&pd_lcd0>; + status = "disabled"; + }; + +Board specific DT entry: + + fimd@11c00000 { + pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; + pinctrl-names = "default"; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/display/fsl,dcu.txt b/Documentation/devicetree/bindings/display/fsl,dcu.txt new file mode 100644 index 000000000000..ebf1be9ae393 --- /dev/null +++ b/Documentation/devicetree/bindings/display/fsl,dcu.txt @@ -0,0 +1,22 @@ +Device Tree bindings for Freescale DCU DRM Driver + +Required properties: +- compatible: Should be one of + * "fsl,ls1021a-dcu". + * "fsl,vf610-dcu". + +- reg: Address and length of the register set for dcu. +- clocks: From common clock binding: handle to dcu clock. +- clock-names: From common clock binding: Shall be "dcu". +- big-endian Boolean property, LS1021A DCU registers are big-endian. +- fsl,panel: The phandle to panel node. + +Examples: +dcu: dcu@2ce0000 { + compatible = "fsl,ls1021a-dcu"; + reg = <0x0 0x2ce0000 0x0 0x10000>; + clocks = <&platform_clk 0>; + clock-names = "dcu"; + big-endian; + fsl,panel = <&panel>; +}; diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt new file mode 100644 index 000000000000..00d5f8ea7ec6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt @@ -0,0 +1,55 @@ +Freescale imx21 Framebuffer + +This framebuffer driver supports devices imx1, imx21, imx25, and imx27. + +Required properties: +- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21 +- reg : Should contain 1 register ranges(address and length) +- interrupts : One interrupt of the fb dev + +Required nodes: +- display: Phandle to a display node as described in + Documentation/devicetree/bindings/display/display-timing.txt + Additional, the display node has to define properties: + - bits-per-pixel: Bits per pixel + - fsl,pcr: LCDC PCR value + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. +- fsl,dmacr: DMA Control Register value. This is optional. By default, the + register is not modified as recommended by the datasheet. +- fsl,lpccr: Contrast Control Register value. This property provides the + default value for the contrast control register. + If that property is omitted, the register is zeroed. +- fsl,lscr1: LCDC Sharp Configuration Register value. + +Example: + + imxfb: fb@10021000 { + compatible = "fsl,imx21-fb"; + interrupts = <61>; + reg = <0x10021000 0x1000>; + display = <&display0>; + }; + + ... + + display0: display0 { + model = "Primeview-PD050VL1"; + native-mode = <&timing_disp0>; + bits-per-pixel = <16>; + fsl,pcr = <0xf0c88080>; /* non-standard but required */ + display-timings { + timing_disp0: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <112>; + hfront-porch = <36>; + hsync-len = <32>; + vback-porch = <33>; + vfront-porch = <33>; + vsync-len = <2>; + clock-frequency = <25000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt new file mode 100644 index 000000000000..971c3eedb1c7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt @@ -0,0 +1,105 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,display-subsystem"; + ports = <&ipu_di0>; +}; + + +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- resets: phandle pointing to the system reset controller and + reset line index, see reset/fsl,imx-src.txt for details +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. + +example: + +ipu: ipu@18000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; + resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +Optional properties: +- interface_pix_fmt: How this display is connected to the + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel +- port@[0-1]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0 is the input port connected to the IPU display interface, + port 1 is the output port connected to a panel. + +example: + +display@di0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + interface-pix-fmt = "rgb24"; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; + +panel { + ... + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/imx/hdmi.txt b/Documentation/devicetree/bindings/display/imx/hdmi.txt new file mode 100644 index 000000000000..1b756cf9afb0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/hdmi.txt @@ -0,0 +1,58 @@ +Device-Tree bindings for HDMI Transmitter + +HDMI Transmitter +================ + +The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with accompanying PHY IP. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". + - gpr : should be <&gpr>. + The phandle points to the iomuxc-gpr region containing the HDMI + multiplexer control register. + - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + - port@[0-4]: Up to four port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + corresponding to the four inputs to the HDMI multiplexer. + +Optional properties: + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + +example: + + gpr: iomuxc-gpr@020e0000 { + /* ... */ + }; + + hdmi: hdmi@0120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt new file mode 100644 index 000000000000..0a175d991b52 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -0,0 +1,146 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.txt, and in + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain either an of graph link to a panel device node +or a display-timings node that describes the video timings for the connected +LVDS display as well as the fsl,data-mapping and fsl,data-width properties. + +Required properties: + - reg : should be <0> or <1> + - port: Input and output port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. + On i.MX5, the internal two-input-multiplexer is used. Due to hardware + limitations, only one input port (port@[0,1]) can be used for each channel + (lvds-channel@[0,1], respectively). + On i.MX6, there should be four input ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected + to a panel input port. Optionally, the output port can be left out if + display-timings are used instead. + +Optional properties (required if display-timings are used): + - display-timings : A node that describes the display timings as defined in + Documentation/devicetree/bindings/display/display-timing.txt. + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + /* Using an of-graph endpoint link to connect the panel */ + lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + + port@2 { + reg = <2>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + /* Using display-timings and fsl,data-mapping/width instead */ + lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; + +panel: lvds-panel { + /* ... */ + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt new file mode 100644 index 000000000000..309c47f25b87 --- /dev/null +++ b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt @@ -0,0 +1,34 @@ +PXA LCD Controller +------------------ + +Required properties: + - compatible : one of these + "marvell,pxa2xx-lcdc", + "marvell,pxa270-lcdc", + "marvell,pxa300-lcdc" + - reg : should contain 1 register range (address and length). + - interrupts : framebuffer controller interrupt. + - clocks: phandle to input clocks + +Required nodes: + - port: connection to the LCD panel (see video-interfaces.txt) + This node must have its properties bus-width and remote-endpoint set. + If the panel is not a TFT color panel, then a "lcd-type" property in + the panel should specify the panel type. + This panel node should be in the board dts. + +Example: + lcd-controller@40500000 { + compatible = "marvell,pxa2xx-lcdc"; + reg = <0x44000000 0x10000>; + interrupts = <17>; + clocks = <&clks CLK_LCD>; + status = "okay"; + + port { + lcdc_out: endpoint { + remote-endpoint = <&panel_in>; + bus-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt new file mode 100644 index 000000000000..973c27273772 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt @@ -0,0 +1,98 @@ +MIPI DSI (Display Serial Interface) busses +========================================== + +The MIPI Display Serial Interface specifies a serial bus and a protocol for +communication between a host and up to four peripherals. This document will +define the syntax used to represent a DSI bus in a device tree. + +This document describes DSI bus-specific properties only or defines existing +standard properties in the context of the DSI bus. + +Each DSI host provides a DSI bus. The DSI host controller's node contains a +set of properties that characterize the bus. Child nodes describe individual +peripherals on that bus. + +The following assumes that only a single peripheral is connected to a DSI +host. Experience shows that this is true for the large majority of setups. + +DSI host +-------- + +In addition to the standard properties and those defined by the parent bus of +a DSI host, the following properties apply to a node representing a DSI host. + +Required properties: +- #address-cells: The number of cells required to represent an address on the + bus. DSI peripherals are addressed using a 2-bit virtual channel number, so + a maximum of 4 devices can be addressed on a single bus. Hence the value of + this property should be 1. +- #size-cells: Should be 0. There are cases where it makes sense to use a + different value here. See below. + +DSI peripheral +-------------- + +Peripherals are represented as child nodes of the DSI host's node. Properties +described here apply to all DSI peripherals, but individual bindings may want +to define additional, device-specific properties. + +Required properties: +- reg: The virtual channel number of a DSI peripheral. Must be in the range + from 0 to 3. + +Some DSI peripherals respond to more than a single virtual channel. In that +case two alternative representations can be chosen: +- The reg property can take multiple entries, one for each virtual channel + that the peripheral responds to. +- If the virtual channels that a peripheral responds to are consecutive, the + #size-cells can be set to 1. The first cell of each entry in the reg + property is the number of the first virtual channel and the second cell is + the number of consecutive virtual channels. + +Example +------- + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <0>; + + /* peripheral responds to virtual channel 0 */ + peripheral@0 { + compatible = "..."; + reg = <0>; + }; + + ... + }; + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <0>; + + /* peripheral responds to virtual channels 0 and 2 */ + peripheral@0 { + compatible = "..."; + reg = <0, 2>; + }; + + ... + }; + + dsi-host { + ... + + #address-cells = <1>; + #size-cells = <1>; + + /* peripheral responds to virtual channels 1, 2 and 3 */ + peripheral@1 { + compatible = "..."; + reg = <1 3>; + }; + + ... + }; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt new file mode 100644 index 000000000000..f344b9e49198 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -0,0 +1,149 @@ +Qualcomm Technologies Inc. adreno/snapdragon DSI output + +DSI Controller: +Required properties: +- compatible: + * "qcom,mdss-dsi-ctrl" +- reg: Physical base address and length of the registers of controller +- reg-names: The names of register regions. The following regions are required: + * "dsi_ctrl" +- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should + be 0 or 1, since we have 2 DSI controllers at most for now. +- interrupts: The interrupt signal from the DSI block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "bus_clk" + * "byte_clk" + * "core_clk" + * "core_mmss_clk" + * "iface_clk" + * "mdp_core_clk" + * "pixel_clk" +- vdd-supply: phandle to vdd regulator device node +- vddio-supply: phandle to vdd-io regulator device node +- vdda-supply: phandle to vdda regulator device node +- qcom,dsi-phy: phandle to DSI PHY device node + +Optional properties: +- panel@0: Node of panel connected to this DSI controller. + See files in Documentation/devicetree/bindings/display/panel/ for each supported + panel. +- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is + driving a panel which needs 2 DSI links. +- qcom,master-dsi: Boolean value indicating if the DSI controller is driving + the master link of the 2-DSI panel. +- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is + driving a 2-DSI panel whose 2 links need receive command simultaneously. +- interrupt-parent: phandle to the MDP block if the interrupt signal is routed + through MDP block +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-n: the "sleep" pinctrl state +- port: DSI controller output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected panel's endpoint. + See Documentation/devicetree/bindings/graph.txt for device graph info. + +DSI PHY: +Required properties: +- compatible: Could be the following + * "qcom,dsi-phy-28nm-hpm" + * "qcom,dsi-phy-28nm-lp" + * "qcom,dsi-phy-20nm" +- reg: Physical base address and length of the registers of PLL, PHY and PHY + regulator +- reg-names: The names of register regions. The following regions are required: + * "dsi_pll" + * "dsi_phy" + * "dsi_phy_regulator" +- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should + be 0 or 1, since we have 2 DSI PHYs at most for now. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "iface_clk" +- vddio-supply: phandle to vdd-io regulator device node + +Optional properties: +- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY + regulator is wanted. + +Example: + mdss_dsi0: qcom,mdss_dsi@fd922800 { + compatible = "qcom,mdss-dsi-ctrl"; + qcom,dsi-host-index = <0>; + interrupt-parent = <&mdss_mdp>; + interrupts = <4 0>; + reg-names = "dsi_ctrl"; + reg = <0xfd922800 0x200>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "bus_clk", + "byte_clk", + "core_clk", + "core_mmss_clk", + "iface_clk", + "mdp_core_clk", + "pixel_clk"; + clocks = + <&mmcc MDSS_AXI_CLK>, + <&mmcc MDSS_BYTE0_CLK>, + <&mmcc MDSS_ESC0_CLK>, + <&mmcc MMSS_MISC_AHB_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_PCLK0_CLK>; + vdda-supply = <&pma8084_l2>; + vdd-supply = <&pma8084_l22>; + vddio-supply = <&pma8084_l12>; + + qcom,dsi-phy = <&mdss_dsi_phy0>; + + qcom,dual-dsi-mode; + qcom,master-dsi; + qcom,sync-dual-dsi; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdss_dsi_active>; + pinctrl-1 = <&mdss_dsi_suspend>; + + panel: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + link2 = <&secondary>; + + power-supply = <...>; + backlight = <...>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { + compatible = "qcom,dsi-phy-28nm-hpm"; + qcom,dsi-phy-index = <0>; + reg-names = + "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + reg = <0xfd922a00 0xd4>, + <0xfd922b00 0x2b0>, + <0xfd922d80 0x7b>; + clock-names = "iface_clk"; + clocks = <&mmcc MDSS_AHB_CLK>; + vddio-supply = <&pma8084_l12>; + + qcom,dsi-phy-regulator-ldo-mode; + }; diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt new file mode 100644 index 000000000000..3a20f6ea5898 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -0,0 +1,60 @@ +Qualcomm Technologies Inc. adreno/snapdragon eDP output + +Required properties: +- compatible: + * "qcom,mdss-edp" +- reg: Physical base address and length of the registers of controller and PLL +- reg-names: The names of register regions. The following regions are required: + * "edp" + * "pll_base" +- interrupts: The interrupt signal from the eDP block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "mdp_core_clk" + * "pixel_clk" + * "link_clk" +- #clock-cells: The value should be 1. +- vdda-supply: phandle to vdda regulator device node +- lvl-vdd-supply: phandle to regulator device node which is used to supply power + to HPD receiving chip +- panel-en-gpios: GPIO pin to supply power to panel. +- panel-hpd-gpios: GPIO pin used for eDP hpd. + + +Optional properties: +- interrupt-parent: phandle to the MDP block if the interrupt signal is routed + through MDP block + +Example: + mdss_edp: qcom,mdss_edp@fd923400 { + compatible = "qcom,mdss-edp"; + reg-names = + "edp", + "pll_base"; + reg = <0xfd923400 0x700>, + <0xfd923a00 0xd4>; + interrupt-parent = <&mdss_mdp>; + interrupts = <12 0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "core_clk", + "pixel_clk", + "iface_clk", + "link_clk", + "mdp_core_clk"; + clocks = + <&mmcc MDSS_EDPAUX_CLK>, + <&mmcc MDSS_EDPPIXEL_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_EDPLINK_CLK>, + <&mmcc MDSS_MDP_CLK>; + #clock-cells = <1>; + vdda-supply = <&pma8084_l12>; + lvl-vdd-supply = <&lvl_vreg>; + panel-en-gpios = <&tlmm 137 0>; + panel-hpd-gpios = <&tlmm 103 0>; + }; diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt new file mode 100644 index 000000000000..67d0a58dbb77 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -0,0 +1,52 @@ +Qualcomm adreno/snapdragon GPU + +Required properties: +- compatible: "qcom,adreno-3xx" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the gpu. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "mem_iface_clk" +- qcom,chipid: gpu chip-id. Note this may become optional for future + devices if we can reliably read the chipid from hw +- qcom,gpu-pwrlevels: list of operating points + - compatible: "qcom,gpu-pwrlevels" + - for each qcom,gpu-pwrlevel: + - qcom,gpu-freq: requested gpu clock speed + - NOTE: downstream android driver defines additional parameters to + configure memory bandwidth scaling per OPP. + +Example: + +/ { + ... + + gpu: qcom,kgsl-3d0@4300000 { + compatible = "qcom,adreno-3xx"; + reg = <0x04300000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = <GIC_SPI 80 0>; + interrupt-names = "kgsl_3d0_irq"; + clock-names = + "core_clk", + "iface_clk", + "mem_iface_clk"; + clocks = + <&mmcc GFX3D_CLK>, + <&mmcc GFX3D_AHB_CLK>, + <&mmcc MMSS_IMEM_AHB_CLK>; + qcom,chipid = <0x03020100>; + qcom,gpu-pwrlevels { + compatible = "qcom,gpu-pwrlevels"; + qcom,gpu-pwrlevel@0 { + qcom,gpu-freq = <450000000>; + }; + qcom,gpu-pwrlevel@1 { + qcom,gpu-freq = <27000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt new file mode 100644 index 000000000000..e926239e1101 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -0,0 +1,55 @@ +Qualcomm adreno/snapdragon hdmi output + +Required properties: +- compatible: one of the following + * "qcom,hdmi-tx-8994" + * "qcom,hdmi-tx-8084" + * "qcom,hdmi-tx-8974" + * "qcom,hdmi-tx-8660" + * "qcom,hdmi-tx-8960" +- reg: Physical base address and length of the controller's registers +- reg-names: "core_physical" +- interrupts: The interrupt signal from the hdmi block. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin +- qcom,hdmi-tx-ddc-data-gpio: ddc data pin +- qcom,hdmi-tx-hpd-gpio: hpd pin +- core-vdda-supply: phandle to supply regulator +- hdmi-mux-supply: phandle to mux regulator + +Optional properties: +- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-1: the "sleep" pinctrl state + +Example: + +/ { + ... + + hdmi: qcom,hdmi-tx-8960@4a00000 { + compatible = "qcom,hdmi-tx-8960"; + reg-names = "core_physical"; + reg = <0x04a00000 0x1000>; + interrupts = <GIC_SPI 79 0>; + clock-names = + "core_clk", + "master_iface_clk", + "slave_iface_clk"; + clocks = + <&mmcc HDMI_APP_CLK>, + <&mmcc HDMI_M_AHB_CLK>, + <&mmcc HDMI_S_AHB_CLK>; + qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + hdmi-mux-supply = <&ext_3p3v>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&hpd_active &ddc_active &cec_active>; + pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt new file mode 100644 index 000000000000..1a0598e5279d --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp.txt @@ -0,0 +1,48 @@ +Qualcomm adreno/snapdragon display controller + +Required properties: +- compatible: + * "qcom,mdp" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- connectors: array of phandles for output device(s) +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "lut_clk" + * "src_clk" + * "hdmi_clk" + * "mpd_clk" + +Optional properties: +- gpus: phandle for gpu device + +Example: + +/ { + ... + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + connectors = <&hdmi>; + gpus = <&gpu>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "src_clk", + "hdmi_clk", + "mdp_clk"; + clocks = + <&mmcc MDP_SRC>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc TV_SRC>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mxsfb.txt b/Documentation/devicetree/bindings/display/mxsfb.txt new file mode 100644 index 000000000000..96ec5179c8a0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mxsfb.txt @@ -0,0 +1,49 @@ +* Freescale MXS LCD Interface (LCDIF) + +Required properties: +- compatible: Should be "fsl,<chip>-lcdif". Supported chips include + imx23 and imx28. +- reg: Address and length of the register set for lcdif +- interrupts: Should contain lcdif interrupts +- display : phandle to display node (see below for details) + +* display node + +Required properties: +- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. +- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. + +Required sub-node: +- display-timings : Refer to binding doc display-timing.txt for details. + +Examples: + +lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; + reg = <0x80030000 2000>; + interrupts = <38 86>; + + display: display { + bits-per-pixel = <32>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <33500000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <164>; + hback-porch = <89>; + hsync-len = <10>; + vback-porch = <23>; + vfront-porch = <10>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt b/Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt new file mode 100644 index 000000000000..83e2cae1cc1b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ampire,am800480r3tmqwa1h.txt @@ -0,0 +1,7 @@ +Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "ampire,am800480r3tmqwa1h" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b080uan01.txt b/Documentation/devicetree/bindings/display/panel/auo,b080uan01.txt new file mode 100644 index 000000000000..bae0e2b51467 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b080uan01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 8.0" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101ean01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b101aw03.txt b/Documentation/devicetree/bindings/display/panel/auo,b101aw03.txt new file mode 100644 index 000000000000..72e088a4fb3a --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b101aw03.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101aw03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b101ean01.txt b/Documentation/devicetree/bindings/display/panel/auo,b101ean01.txt new file mode 100644 index 000000000000..3590b0741619 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b101ean01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101ean01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b101xtn01.txt b/Documentation/devicetree/bindings/display/panel/auo,b101xtn01.txt new file mode 100644 index 000000000000..889d511d66c9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b101xtn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101xtn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b116xw03.txt b/Documentation/devicetree/bindings/display/panel/auo,b116xw03.txt new file mode 100644 index 000000000000..690d0a568ef3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b116xw03.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 11.6" HD (1366x768) color TFT-LCD panel + +Required properties: +- compatible: should be "auo,b116xw03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b133htn01.txt b/Documentation/devicetree/bindings/display/panel/auo,b133htn01.txt new file mode 100644 index 000000000000..302226b5bb55 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b133htn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) color TFT-LCD panel + +Required properties: +- compatible: should be "auo,b133htn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,b133xtn01.txt b/Documentation/devicetree/bindings/display/panel/auo,b133xtn01.txt new file mode 100644 index 000000000000..7443b7c76769 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,b133xtn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "auo,b133xtn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/avic,tm070ddh03.txt b/Documentation/devicetree/bindings/display/panel/avic,tm070ddh03.txt new file mode 100644 index 000000000000..b6f2f3e8f44e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/avic,tm070ddh03.txt @@ -0,0 +1,7 @@ +Shanghai AVIC Optoelectronics 7" 1024x600 color TFT-LCD panel + +Required properties: +- compatible: should be "avic,tm070ddh03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wa01a.txt b/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wa01a.txt new file mode 100644 index 000000000000..f24614e4d5ec --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wa01a.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa101wa01a" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wb03.txt b/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wb03.txt new file mode 100644 index 000000000000..0ab2c05a4c22 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/chunghwa,claa101wb03.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa101wb03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/display-timing.txt b/Documentation/devicetree/bindings/display/panel/display-timing.txt new file mode 100644 index 000000000000..e1d4a0b59612 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/display-timing.txt @@ -0,0 +1,110 @@ +display-timing bindings +======================= + +display-timings node +-------------------- + +required properties: + - none + +optional properties: + - native-mode: The native mode for the display, in case multiple modes are + provided. When omitted, assume the first node is the native. + +timing subnode +-------------- + +required properties: + - hactive, vactive: display resolution + - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: vertical display timing parameters in + lines + - clock-frequency: display clock in Hz + +optional properties: + - hsync-active: hsync pulse is active low/high/ignored + - vsync-active: vsync pulse is active low/high/ignored + - de-active: data-enable pulse is active low/high/ignored + - pixelclk-active: with + - active high = drive pixel data on rising edge/ + sample data on falling edge + - active low = drive pixel data on falling edge/ + sample data on rising edge + - ignored = ignored + - interlaced (bool): boolean to enable interlaced mode + - doublescan (bool): boolean to enable doublescan mode + - doubleclk (bool): boolean to enable doubleclock mode + +All the optional properties that are not bool follow the following logic: + <1>: high active + <0>: low active + omitted: not used on hardware + +There are different ways of describing the capabilities of a display. The +devicetree representation corresponds to the one commonly found in datasheets +for displays. If a display supports multiple signal timings, the native-mode +can be specified. + +The parameters are defined as: + + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vback_porch | | | + | | ↓ | | | + +----------#######################################----------+-------+ + | # ↑ # | | + | # | # | | + | hback # | # hfront | hsync | + | porch # | hactive # porch | len | + |<-------->#<-------+--------------------------->#<-------->|<----->| + | # | # | | + | # |vactive # | | + | # | # | | + | # ↓ # | | + +----------#######################################----------+-------+ + | | ↑ | | | + | | |vfront_porch | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vsync_len | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + +Example: + + display-timings { + native-mode = <&timing0>; + timing0: 1080p24 { + /* 1920x1080p24 */ + clock-frequency = <52000000>; + hactive = <1920>; + vactive = <1080>; + hfront-porch = <25>; + hback-porch = <25>; + hsync-len = <25>; + vback-porch = <2>; + vfront-porch = <2>; + vsync-len = <2>; + hsync-active = <1>; + }; + }; + +Every required property also supports the use of ranges, so the commonly used +datasheet description with minimum, typical and maximum values can be used. + +Example: + + timing1: timing { + /* 1920x1080p24 */ + clock-frequency = <148500000>; + hactive = <1920>; + vactive = <1080>; + hsync-len = <0 44 60>; + hfront-porch = <80 88 95>; + hback-porch = <100 148 160>; + vfront-porch = <0 4 6>; + vback-porch = <0 36 50>; + vsync-len = <0 5 6>; + }; diff --git a/Documentation/devicetree/bindings/display/panel/edt,et057090dhu.txt b/Documentation/devicetree/bindings/display/panel/edt,et057090dhu.txt new file mode 100644 index 000000000000..4903d7b1d947 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/edt,et057090dhu.txt @@ -0,0 +1,7 @@ +Emerging Display Technology Corp. 5.7" VGA TFT LCD panel + +Required properties: +- compatible: should be "edt,et057090dhu" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/edt,et070080dh6.txt b/Documentation/devicetree/bindings/display/panel/edt,et070080dh6.txt new file mode 100644 index 000000000000..20cb38e836e4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/edt,et070080dh6.txt @@ -0,0 +1,10 @@ +Emerging Display Technology Corp. ET070080DH6 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "edt,et070080dh6" + +This panel is the same as ETM0700G0DH6 except for the touchscreen. +ET070080DH6 is the model with resistive touch. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/edt,etm0700g0dh6.txt b/Documentation/devicetree/bindings/display/panel/edt,etm0700g0dh6.txt new file mode 100644 index 000000000000..ee4b18053e40 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/edt,etm0700g0dh6.txt @@ -0,0 +1,10 @@ +Emerging Display Technology Corp. ETM0700G0DH6 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "edt,etm0700g0dh6" + +This panel is the same as ET070080DH6 except for the touchscreen. +ETM0700G0DH6 is the model with capacitive multitouch. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/foxlink,fl500wvr00-a0t.txt b/Documentation/devicetree/bindings/display/panel/foxlink,fl500wvr00-a0t.txt new file mode 100644 index 000000000000..b47f9d87bc19 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/foxlink,fl500wvr00-a0t.txt @@ -0,0 +1,7 @@ +Foxlink Group 5" WVGA TFT LCD panel + +Required properties: +- compatible: should be "foxlink,fl500wvr00-a0t" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/giantplus,gpg482739qs5.txt b/Documentation/devicetree/bindings/display/panel/giantplus,gpg482739qs5.txt new file mode 100644 index 000000000000..24b0b624434b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/giantplus,gpg482739qs5.txt @@ -0,0 +1,7 @@ +GiantPlus GPG48273QS5 4.3" (480x272) WQVGA TFT LCD panel + +Required properties: +- compatible: should be "giantplus,gpg48273qs5" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/hannstar,hsd070pww1.txt b/Documentation/devicetree/bindings/display/panel/hannstar,hsd070pww1.txt new file mode 100644 index 000000000000..7da1d5c038ff --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/hannstar,hsd070pww1.txt @@ -0,0 +1,7 @@ +HannStar Display Corp. HSD070PWW1 7.0" WXGA TFT LCD panel + +Required properties: +- compatible: should be "hannstar,hsd070pww1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/hannstar,hsd100pxn1.txt b/Documentation/devicetree/bindings/display/panel/hannstar,hsd100pxn1.txt new file mode 100644 index 000000000000..8270319a99de --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/hannstar,hsd100pxn1.txt @@ -0,0 +1,7 @@ +HannStar Display Corp. HSD100PXN1 10.1" XGA LVDS panel + +Required properties: +- compatible: should be "hannstar,hsd100pxn1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/hit,tx23d38vm0caa.txt b/Documentation/devicetree/bindings/display/panel/hit,tx23d38vm0caa.txt new file mode 100644 index 000000000000..04caaae19af6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/hit,tx23d38vm0caa.txt @@ -0,0 +1,7 @@ +Hitachi Ltd. Corporation 9" WVGA (800x480) TFT LCD panel + +Required properties: +- compatible: should be "hit,tx23d38vm0caa" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,at043tn24.txt b/Documentation/devicetree/bindings/display/panel/innolux,at043tn24.txt new file mode 100644 index 000000000000..4104226b61bc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,at043tn24.txt @@ -0,0 +1,7 @@ +Innolux AT043TN24 4.3" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at043tn24" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,g121i1-l01.txt b/Documentation/devicetree/bindings/display/panel/innolux,g121i1-l01.txt new file mode 100644 index 000000000000..2743b07cd2f2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,g121i1-l01.txt @@ -0,0 +1,7 @@ +Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel + +Required properties: +- compatible: should be "innolux,g121i1-l01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,n116bge.txt b/Documentation/devicetree/bindings/display/panel/innolux,n116bge.txt new file mode 100644 index 000000000000..081bb939ed31 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,n116bge.txt @@ -0,0 +1,7 @@ +Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "innolux,n116bge" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,n156bge-l21.txt b/Documentation/devicetree/bindings/display/panel/innolux,n156bge-l21.txt new file mode 100644 index 000000000000..7825844aafdf --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,n156bge-l21.txt @@ -0,0 +1,7 @@ +InnoLux 15.6" WXGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,n156bge-l21" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,zj070na-01p.txt b/Documentation/devicetree/bindings/display/panel/innolux,zj070na-01p.txt new file mode 100644 index 000000000000..824f87f1526d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,zj070na-01p.txt @@ -0,0 +1,7 @@ +Innolux Corporation 7.0" WSVGA (1024x600) TFT LCD panel + +Required properties: +- compatible: should be "innolux,zj070na-01p" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lb070wv8.txt b/Documentation/devicetree/bindings/display/panel/lg,lb070wv8.txt new file mode 100644 index 000000000000..a7588e5259cf --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lb070wv8.txt @@ -0,0 +1,7 @@ +LG 7" (800x480 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lb070wv8" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt b/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt new file mode 100644 index 000000000000..5e649cb9aa1a --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt @@ -0,0 +1,7 @@ +LG Corporation 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "lg,ld070wx3-sl01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt b/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt new file mode 100644 index 000000000000..824441f4e95a --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt @@ -0,0 +1,19 @@ +LG LG4573 TFT Liquid Crystal Display with SPI control bus + +Required properties: + - compatible: "lg,lg4573" + - reg: address of the panel on the SPI bus + +The panel must obey rules for SPI slave device specified in document [1]. + +[1]: Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + lcd_panel: display@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lg,lg4573"; + spi-max-frequency = <10000000>; + reg = <0>; + }; diff --git a/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt b/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt new file mode 100644 index 000000000000..a04fd2b2e73d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt @@ -0,0 +1,7 @@ +LG Corporation 5" HD TFT LCD panel + +Required properties: +- compatible: should be "lg,lh500wx1-sd03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp129qe.txt b/Documentation/devicetree/bindings/display/panel/lg,lp129qe.txt new file mode 100644 index 000000000000..9f262e0c5a2e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp129qe.txt @@ -0,0 +1,7 @@ +LG 12.9" (2560x1700 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp129qe" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt b/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt new file mode 100644 index 000000000000..1a1e653e5407 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt @@ -0,0 +1,33 @@ +LG.Philips LB035Q02 Panel +========================= + +Required properties: +- compatible: "lgphilips,lb035q02" +- enable-gpios: panel enable gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "lgphilips,lb035q02"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + enable-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/nec,nl4827hc19-05b.txt b/Documentation/devicetree/bindings/display/panel/nec,nl4827hc19-05b.txt new file mode 100644 index 000000000000..8e1914d1edb8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/nec,nl4827hc19-05b.txt @@ -0,0 +1,7 @@ +NEC LCD Technologies,Ltd. WQVGA TFT LCD panel + +Required properties: +- compatible: should be "nec,nl4827hc19-05b" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/okaya,rs800480t-7x0gp.txt b/Documentation/devicetree/bindings/display/panel/okaya,rs800480t-7x0gp.txt new file mode 100644 index 000000000000..ddf8e211d382 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/okaya,rs800480t-7x0gp.txt @@ -0,0 +1,7 @@ +OKAYA Electric America, Inc. RS800480T-7X0GP 7" WVGA LCD panel + +Required properties: +- compatible: should be "okaya,rs800480t-7x0gp" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ortustech,com43h4m85ulc.txt b/Documentation/devicetree/bindings/display/panel/ortustech,com43h4m85ulc.txt new file mode 100644 index 000000000000..de19e9398618 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ortustech,com43h4m85ulc.txt @@ -0,0 +1,7 @@ +OrtusTech COM43H4M85ULC Blanview 3.7" TFT-LCD panel + +Required properties: +- compatible: should be "ortustech,com43h4m85ulc" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f004b00.txt b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f004b00.txt new file mode 100644 index 000000000000..d328b0341bf4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f004b00.txt @@ -0,0 +1,7 @@ +Panasonic Corporation 10.1" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "panasonic,vvx10f004b00" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt new file mode 100644 index 000000000000..216c894d4f99 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt @@ -0,0 +1,45 @@ +Generic MIPI DPI Panel +====================== + +Required properties: +- compatible: "panel-dpi" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: panel enable gpio + +Required nodes: +- "panel-timing" containing video timings + (Documentation/devicetree/bindings/display/display-timing.txt) +- Video port for DPI input + +Example +------- + +lcd0: display@0 { + compatible = "samsung,lte430wq-f0c", "panel-dpi"; + label = "lcd"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt b/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt new file mode 100644 index 000000000000..dce48eb9db57 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt @@ -0,0 +1,29 @@ +Generic MIPI DSI Command Mode Panel +=================================== + +Required properties: +- compatible: "panel-dsi-cm" + +Optional properties: +- label: a symbolic name for the panel +- reset-gpios: panel reset gpio +- te-gpios: panel TE gpio + +Required nodes: +- Video port for DSI input + +Example +------- + +lcd0: display { + compatible = "tpo,taal", "panel-dsi-cm"; + label = "lcd0"; + + reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; + + port { + lcd0_in: endpoint { + remote-endpoint = <&dsi1_out_ep>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt new file mode 100644 index 000000000000..fc595d9b985b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt @@ -0,0 +1,66 @@ +Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus + +Required properties: + - compatible: "samsung,ld9040" + - reg: address of the panel on SPI bus + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel according to [1] + +The panel must obey rules for SPI slave device specified in document [2]. + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [3]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/display/display-timing.txt +[2]: Documentation/devicetree/bindings/spi/spi-bus.txt +[3]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + lcd@0 { + compatible = "samsung,ld9040"; + reg = <0>; + vdd3-supply = <&ldo7_reg>; + vci-supply = <&ldo17_reg>; + reset-gpios = <&gpy4 5 0>; + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + power-on-delay = <10>; + reset-delay = <10>; + panel-width-mm = <90>; + panel-height-mm = <154>; + + display-timings { + timing { + clock-frequency = <23492370>; + hactive = <480>; + vactive = <800>; + hback-porch = <16>; + hfront-porch = <16>; + vback-porch = <2>; + vfront-porch = <28>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <0>; + }; + }; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_dpi_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ltn101nt05.txt b/Documentation/devicetree/bindings/display/panel/samsung,ltn101nt05.txt new file mode 100644 index 000000000000..ef522c6bb85f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ltn101nt05.txt @@ -0,0 +1,7 @@ +Samsung Electronics 10.1" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "samsung,ltn101nt05" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ltn140at29-301.txt b/Documentation/devicetree/bindings/display/panel/samsung,ltn140at29-301.txt new file mode 100644 index 000000000000..e7f969d891cc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ltn140at29-301.txt @@ -0,0 +1,7 @@ +Samsung Electronics 14" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "samsung,ltn140at29-301" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt new file mode 100644 index 000000000000..25701c81b5e0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt @@ -0,0 +1,56 @@ +Samsung S6E8AA0 AMOLED LCD 5.3 inch panel + +Required properties: + - compatible: "samsung,s6e8aa0" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel as described by [1] + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - init-delay: delay after initialization sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + - flip-horizontal: boolean to flip image horizontally + - flip-vertical: boolean to flip image vertically + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/display/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + panel { + compatible = "samsung,s6e8aa0"; + reg = <0>; + vdd3-supply = <&vcclcd_reg>; + vci-supply = <&vlcd_reg>; + reset-gpios = <&gpy4 5 0>; + power-on-delay= <50>; + reset-delay = <100>; + init-delay = <100>; + panel-width-mm = <58>; + panel-height-mm = <103>; + flip-horizontal; + flip-vertical; + + display-timings { + timing0: timing-0 { + clock-frequency = <57153600>; + hactive = <720>; + vactive = <1280>; + hfront-porch = <5>; + hback-porch = <5>; + hsync-len = <5>; + vfront-porch = <13>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq101r1sx01.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq101r1sx01.txt new file mode 100644 index 000000000000..f522bb8e47e1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq101r1sx01.txt @@ -0,0 +1,49 @@ +Sharp Microelectronics 10.1" WQXGA TFT LCD panel + +This panel requires a dual-channel DSI host to operate. It supports two modes: +- left-right: each channel drives the left or right half of the screen +- even-odd: each channel drives the even or odd lines of the screen + +Each of the DSI channels controls a separate DSI peripheral. The peripheral +driven by the first link (DSI-LINK1), left or even, is considered the primary +peripheral and controls the device. The 'link2' property contains a phandle +to the peripheral driven by the second link (DSI-LINK2, right or odd). + +Note that in video mode the DSI-LINK1 interface always provides the left/even +pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it +is possible to program either link to drive the left/even or right/odd pixels +but for the sake of consistency this binding assumes that the same assignment +is chosen as for video mode. + +Required properties: +- compatible: should be "sharp,lq101r1sx01" +- reg: DSI virtual channel of the peripheral + +Required properties (for DSI-LINK1 only): +- link2: phandle to the DSI peripheral on the secondary link. Note that the + presence of this property marks the containing node as DSI-LINK1. +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties (for DSI-LINK1 only): +- backlight: phandle of the backlight device attached to the panel + +Example: + + dsi@54300000 { + panel: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + + link2 = <&secondary>; + + power-supply = <...>; + backlight = <...>; + }; + }; + + dsi@54400000 { + secondary: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt new file mode 100644 index 000000000000..0cc8981e9d49 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt @@ -0,0 +1,43 @@ +SHARP LS037V7DW01 TFT-LCD panel +=================================== + +Required properties: +- compatible: "sharp,ls037v7dw01" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: a GPIO spec for the optional enable pin. + This pin is the INI pin as specified in the LS037V7DW01.pdf file. +- reset-gpios: a GPIO spec for the optional reset pin. + This pin is the RESB pin as specified in the LS037V7DW01.pdf file. +- mode-gpios: a GPIO + ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file. + +Required nodes: +- Video port for DPI input + +This panel can have zero to five GPIOs to configure to change configuration +between QVGA and VGA mode and the scan direction. As these pins can be also +configured with external pulls, all the GPIOs are considered optional with holes +in the array. + +Example +------- + +Example when connected to a omap2+ based device: + +lcd0: display { + compatible = "sharp,ls037v7dw01"; + power-supply = <&lcd_3v3>; + enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */ + reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */ + mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ + &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ + &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/shelly,sca07010-bfn-lnn.txt b/Documentation/devicetree/bindings/display/panel/shelly,sca07010-bfn-lnn.txt new file mode 100644 index 000000000000..fc1ea9e26c94 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/shelly,sca07010-bfn-lnn.txt @@ -0,0 +1,7 @@ +Shelly SCA07010-BFN-LNN 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "shelly,sca07010-bfn-lnn" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt new file mode 100644 index 000000000000..1341bbf4aa3d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt @@ -0,0 +1,21 @@ +Simple display panel + +Required properties: +- power-supply: regulator to provide the supply voltage + +Optional properties: +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel + +Example: + + panel: panel { + compatible = "cptt,claa101wb01"; + ddc-i2c-bus = <&panelddc>; + + power-supply = <&vdd_pnl_reg>; + enable-gpios = <&gpio 90 0>; + + backlight = <&backlight>; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt b/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt new file mode 100644 index 000000000000..e12333280749 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt @@ -0,0 +1,30 @@ +Sony ACX565AKM SDI Panel +======================== + +Required properties: +- compatible: "sony,acx565akm" + +Optional properties: +- label: a symbolic name for the panel +- reset-gpios: panel reset gpio + +Required nodes: +- Video port for SDI input + +Example +------- + +acx565akm@2 { + compatible = "sony,acx565akm"; + spi-max-frequency = <6000000>; + reg = <2>; + + label = "lcd"; + reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */ + + port { + lcd_in: endpoint { + remote-endpoint = <&sdi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/toppoly,td028ttec1.txt b/Documentation/devicetree/bindings/display/panel/toppoly,td028ttec1.txt new file mode 100644 index 000000000000..7175dc3740ac --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/toppoly,td028ttec1.txt @@ -0,0 +1,30 @@ +Toppoly TD028TTEC1 Panel +======================== + +Required properties: +- compatible: "toppoly,td028ttec1" + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: td028ttec1@0 { + compatible = "toppoly,td028ttec1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; + diff --git a/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt b/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt new file mode 100644 index 000000000000..ec6d62975162 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt @@ -0,0 +1,33 @@ +TPO TD043MTEA1 Panel +==================== + +Required properties: +- compatible: "tpo,td043mtea1" +- reset-gpios: panel reset gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "tpo,td043mtea1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + reset-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt new file mode 100644 index 000000000000..c902323928f7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -0,0 +1,88 @@ +* Renesas R-Car Display Unit (DU) + +Required Properties: + + - compatible: must be one of the following. + - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU + - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU + - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU + + - reg: A list of base address and length of each memory resource, one for + each entry in the reg-names property. + - reg-names: Name of the memory resources. The DU requires one memory + resource for the DU core (named "du") and one memory resource for each + LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical + index). + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifiers for the DU interrupts. + + - clocks: A list of phandles + clock-specifier pairs, one for each entry in + the clock-names property. + - clock-names: Name of the clocks. This property is model-dependent. + - R8A7779 uses a single functional clock. The clock doesn't need to be + named. + - R8A7790 and R8A7791 use one functional clock per channel and one clock + per LVDS encoder. The functional clocks must be named "du.x" with "x" + being the channel numerical index. The LVDS clocks must be named + "lvds.x" with "x" being the LVDS encoder numerical index. + - In addition to the functional and encoder clocks, all DU versions also + support externally supplied pixel clocks. Those clocks are optional. + When supplied they must be named "dclkin.x" with "x" being the input + clock numerical index. + +Required nodes: + +The connections to the DU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each DU output. + + Port 0 Port1 Port2 +----------------------------------------------------------------------------- + R8A7779 (H1) DPAD 0 DPAD 1 - + R8A7790 (H2) DPAD LVDS 0 LVDS 1 + R8A7791 (M2) DPAD LVDS 0 - + + +Example: R8A7790 (R-Car H2) DU + + du: du@feb00000 { + compatible = "renesas,du-r8a7790"; + reg = <0 0xfeb00000 0 0x70000>, + <0 0xfeb90000 0 0x1c>, + <0 0xfeb94000 0 0x1c>; + reg-names = "du", "lvds.0", "lvds.1"; + interrupt-parent = <&gic>; + interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, + <0 268 IRQ_TYPE_LEVEL_HIGH>, + <0 269 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_DU0>, + <&mstp7_clks R8A7790_CLK_DU1>, + <&mstp7_clks R8A7790_CLK_DU2>, + <&mstp7_clks R8A7790_CLK_LVDS0>, + <&mstp7_clks R8A7790_CLK_LVDS1>; + clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + port@1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + port@2 { + reg = <2>; + du_out_lvds1: endpoint { + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt new file mode 100644 index 000000000000..668091f27674 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt @@ -0,0 +1,46 @@ +Rockchip specific extensions to the Synopsys Designware HDMI +================================ + +Required properties: +- compatible: "rockchip,rk3288-dw-hdmi"; +- reg: Physical base address and length of the controller's registers. +- clocks: phandle to hdmi iahb and isfr clocks. +- clock-names: should be "iahb" "isfr" +- rockchip,grf: this soc should set GRF regs to mux vopl/vopb. +- interrupts: HDMI interrupt number +- ports: contain a port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. For + vopb,set the reg = <0> and set the reg = <1> for vopl. +- reg-io-width: the width of the reg:1,4, the value should be 4 on + rk3288 platform + +Optional properties +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" + +Example: +hdmi: hdmi@ff980000 { + compatible = "rockchip,rk3288-dw-hdmi"; + reg = <0xff980000 0x20000>; + reg-io-width = <4>; + ddc-i2c-bus = <&i2c5>; + rockchip,grf = <&grf>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>; + clock-names = "iahb", "isfr"; + status = "disabled"; + ports { + hdmi_in: port { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_hdmi>; + }; + hdmi_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_hdmi>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-drm.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-drm.txt new file mode 100644 index 000000000000..5707af89319d --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-drm.txt @@ -0,0 +1,19 @@ +Rockchip DRM master device +================================ + +The Rockchip DRM master device is a virtual device needed to list all +vop devices or other display interface nodes that comprise the +graphics subsystem. + +Required properties: +- compatible: Should be "rockchip,display-subsystem" +- ports: Should contain a list of phandles pointing to display interface port + of vop devices. vop definitions as defined in + Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt + +example: + +display-subsystem { + compatible = "rockchip,display-subsystem"; + ports = <&vopl_out>, <&vopb_out>; +}; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt new file mode 100644 index 000000000000..d15351f2313d --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -0,0 +1,58 @@ +device-tree bindings for rockchip soc display controller (vop) + +VOP (Visual Output Processor) is the Display Controller for the Rockchip +series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be one of the following + "rockchip,rk3288-vop"; + +- interrupts: should contain a list of all VOP IP block interrupts in the + order: VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: Must contain + aclk_vop: for ddr buffer transfer. + hclk_vop: for ahb bus to R/W the phy regs. + dclk_vop: pixel clock. + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - axi + - ahb + - dclk + +- iommus: required a iommu node + +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: +SoC specific DT entry: + vopb: vopb@ff930000 { + compatible = "rockchip,rk3288-vop"; + reg = <0xff930000 0x19c>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>; + clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; + reset-names = "axi", "ahb", "dclk"; + iommus = <&vopb_mmu>; + vopb_out: port { + #address-cells = <1>; + #size-cells = <0>; + vopb_out_edp: endpoint@0 { + reg = <0>; + remote-endpoint=<&edp_in_vopb>; + }; + vopb_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint=<&hdmi_in_vopb>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt new file mode 100644 index 000000000000..c46ba641a1df --- /dev/null +++ b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt @@ -0,0 +1,33 @@ +Sunxi specific Simple Framebuffer bindings + +This binding documents sunxi specific extensions to the simple-framebuffer +bindings. The sunxi simplefb u-boot code relies on the devicetree containing +pre-populated simplefb nodes. + +These extensions are intended so that u-boot can select the right node based +on which pipeline is being used. As such they are solely intended for +firmware / bootloader use, and the OS should ignore them. + +Required properties: +- compatible: "allwinner,simple-framebuffer" +- allwinner,pipeline, one of: + "de_be0-lcd0" + "de_be1-lcd1" + "de_be0-lcd0-hdmi" + "de_be1-lcd1-hdmi" + +Example: + +chosen { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + framebuffer@0 { + compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; + allwinner,pipeline = "de_be0-lcd0-hdmi"; + clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, + <&ahb_gates 44>; + status = "disabled"; + }; +}; diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer.txt b/Documentation/devicetree/bindings/display/simple-framebuffer.txt new file mode 100644 index 000000000000..4474ef6e0b95 --- /dev/null +++ b/Documentation/devicetree/bindings/display/simple-framebuffer.txt @@ -0,0 +1,86 @@ +Simple Framebuffer + +A simple frame-buffer describes a frame-buffer setup by firmware or +the bootloader, with the assumption that the display hardware has already +been set up to scan out from the memory pointed to by the reg property. + +Since simplefb nodes represent runtime information they must be sub-nodes of +the chosen node (*). Simplefb nodes must be named "framebuffer@<address>". + +If the devicetree contains nodes for the display hardware used by a simplefb, +then the simplefb node must contain a property called "display", which +contains a phandle pointing to the primary display hw node, so that the OS +knows which simplefb to disable when handing over control to a driver for the +real hardware. The bindings for the hw nodes must specify which node is +considered the primary node. + +It is advised to add display# aliases to help the OS determine how to number +things. If display# aliases are used, then if the simplefb node contains a +"display" property then the /aliases/display# path must point to the display +hw node the "display" property points to, otherwise it must point directly +to the simplefb node. + +If a simplefb node represents the preferred console for user interaction, +then the chosen node's stdout-path property should point to it, or to the +primary display hw node, as with display# aliases. If display aliases are +used then it should be set to the alias instead. + +It is advised that devicetree files contain pre-filled, disabled framebuffer +nodes, so that the firmware only needs to update the mode information and +enable them. This way if e.g. later on support for more display clocks get +added, the simplefb nodes will already contain this info and the firmware +does not need to be updated. + +If pre-filled framebuffer nodes are used, the firmware may need extra +information to find the right node. In that case an extra platform specific +compatible and platform specific properties should be used and documented, +see e.g. simple-framebuffer-sunxi.txt . + +Required properties: +- compatible: "simple-framebuffer" +- reg: Should contain the location and size of the framebuffer memory. +- width: The width of the framebuffer in pixels. +- height: The height of the framebuffer in pixels. +- stride: The number of bytes in each line of the framebuffer. +- format: The format of the framebuffer surface. Valid values are: + - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). + - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r). + +Optional properties: +- clocks : List of clocks used by the framebuffer. Clocks listed here + are expected to already be configured correctly. The OS must + ensure these clocks are not modified or disabled while the + simple framebuffer remains active. +- display : phandle pointing to the primary display hardware node + +Example: + +aliases { + display0 = &lcdc0; +} + +chosen { + framebuffer0: framebuffer@1d385000 { + compatible = "simple-framebuffer"; + reg = <0x1d385000 (1600 * 1200 * 2)>; + width = <1600>; + height = <1200>; + stride = <(1600 * 2)>; + format = "r5g6b5"; + clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>; + display = <&lcdc0>; + }; + stdout-path = "display0"; +}; + +soc@01c00000 { + lcdc0: lcdc@1c0c000 { + compatible = "allwinner,sun4i-a10-lcdc"; + ... + }; +}; + + +*) Older devicetree files may have a compatible = "simple-framebuffer" node +in a different place, operating systems must first enumerate any compatible +nodes found under chosen and then check for other compatible nodes. diff --git a/Documentation/devicetree/bindings/display/sm501fb.txt b/Documentation/devicetree/bindings/display/sm501fb.txt new file mode 100644 index 000000000000..9d9f0098092b --- /dev/null +++ b/Documentation/devicetree/bindings/display/sm501fb.txt @@ -0,0 +1,34 @@ +* SM SM501 + +The SM SM501 is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "smi,sm501". +- reg : contain two entries: + - First entry: System Configuration register + - Second entry: IO space (Display Controller register) +- interrupts : SMI interrupt to the cpu should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- mode : select a video mode: + <xres>x<yres>[-<bpp>][@<refresh>] +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. +- little-endian: available on big endian systems, to + set different foreign endian. +- big-endian: available on little endian systems, to + set different foreign endian. + +Example for MPC5200: + display@1,0 { + compatible = "smi,sm501"; + reg = <1 0x00000000 0x00800000 + 1 0x03e00000 0x00200000>; + interrupts = <1 1 3>; + mode = "640x480-32@60"; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/display/ssd1289fb.txt b/Documentation/devicetree/bindings/display/ssd1289fb.txt new file mode 100644 index 000000000000..4fcd5e68cb6e --- /dev/null +++ b/Documentation/devicetree/bindings/display/ssd1289fb.txt @@ -0,0 +1,13 @@ +* Solomon SSD1289 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1289fb". The only supported bus for + now is lbc. + - reg: Should contain address of the controller on the LBC bus. The detail + was described in Documentation/devicetree/bindings/powerpc/fsl/lbc.txt + +Examples: +display@2,0 { + compatible = "solomon,ssd1289fb"; + reg = <0x2 0x0000 0x0004>; +}; diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt new file mode 100644 index 000000000000..d1be78db63f5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -0,0 +1,49 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for + now is i2c, and the supported chips are ssd1305, ssd1306 and ssd1307. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0]. Only required for the ssd1307. + - reset-gpios: Should contain the GPIO used to reset the OLED display + - solomon,height: Height in pixel of the screen driven by the controller + - solomon,width: Width in pixel of the screen driven by the controller + - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is + mapped to. + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + - solomon,segment-no-remap: Display needs normal (non-inverted) data column + to segment mapping + - solomon,com-seq: Display uses sequential COM pin configuration + - solomon,com-lrremap: Display uses left-right COM pin remap + - solomon,com-invdir: Display uses inverted COM pin scan direction + - solomon,com-offset: Number of the COM pin wired to the first display line + - solomon,prechargep1: Length of deselect period (phase 1) in clock cycles. + - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles. + This needs to be the higher, the higher the capacitance + of the OLED's pixels is + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +}; + +ssd1306: oled@3c { + compatible = "solomon,ssd1306fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; + solomon,com-lrremap; + solomon,com-invdir; + solomon,com-offset = <32>; +}; diff --git a/Documentation/devicetree/bindings/display/st,stih4xx.txt b/Documentation/devicetree/bindings/display/st,stih4xx.txt new file mode 100644 index 000000000000..a352ed30cd70 --- /dev/null +++ b/Documentation/devicetree/bindings/display/st,stih4xx.txt @@ -0,0 +1,241 @@ +STMicroelectronics stih4xx platforms + +- sti-vtg: video timing generator + Required properties: + - compatible: "st,vtg" + - reg: Physical base address of the IP registers and length of memory mapped region. + Optional properties: + - interrupts : VTG interrupt number to the CPU. + - st,slave: phandle on a slave vtg + +- sti-vtac: video timing advanced inter dye communication Rx and TX + Required properties: + - compatible: "st,vtac-main" or "st,vtac-aux" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + +- sti-display-subsystem: Master device for DRM sub-components + This device must be the parent of all the sub-components and is responsible + of bind them. + Required properties: + - compatible: "st,sti-display-subsystem" + - ranges: to allow probing of subdevices + +- sti-compositor: frame compositor engine + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-compositor" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + - st,vtg: phandle(s) on vtg device (main and aux) nodes. + +- sti-tvout: video out hardware block + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-tvout" + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + +- sti-hdmi: hdmi output block + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-hdmi"; + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - interrupts : HDMI interrupt number to the CPU. + - interrupt-names: names of the interrupts listed in interrupts property in + the same order + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + - clock-names: names of the clocks listed in clocks property in the same + order. + - ddc: phandle of an I2C controller used for DDC EDID probing + +sti-hda: + Required properties: + must be a child of sti-display-subsystem + - compatible: "st,stih<chip>-hda" + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + +sti-dvo: + Required properties: + must be a child of sti-display-subsystem + - compatible: "st,stih<chip>-dvo" + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + - pinctrl-0: pin control handle + - pinctrl-names: names of the pin control states to use + - sti,panel: phandle of the panel connected to the DVO output + +sti-hqvdp: + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-hqvdp" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + - st,vtg: phandle on vtg main device node. + +Example: + +/ { + ... + + vtg_main_slave: sti-vtg-main-slave@fe85A800 { + compatible = "st,vtg"; + reg = <0xfe85A800 0x300>; + interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>; + }; + + vtg_main: sti-vtg-main-master@fd348000 { + compatible = "st,vtg"; + reg = <0xfd348000 0x400>; + st,slave = <&vtg_main_slave>; + }; + + vtg_aux_slave: sti-vtg-aux-slave@fd348400 { + compatible = "st,vtg"; + reg = <0xfe858200 0x300>; + interrupts = <GIC_SPI 176 IRQ_TYPE_NONE>; + }; + + vtg_aux: sti-vtg-aux-master@fd348400 { + compatible = "st,vtg"; + reg = <0xfd348400 0x400>; + st,slave = <&vtg_aux_slave>; + }; + + + sti-vtac-rx-main@fee82800 { + compatible = "st,vtac-main"; + reg = <0xfee82800 0x200>; + clock-names = "vtac"; + clocks = <&clk_m_a2_div0 CLK_M_VTAC_MAIN_PHY>; + }; + + sti-vtac-rx-aux@fee82a00 { + compatible = "st,vtac-aux"; + reg = <0xfee82a00 0x200>; + clock-names = "vtac"; + clocks = <&clk_m_a2_div0 CLK_M_VTAC_AUX_PHY>; + }; + + sti-vtac-tx-main@fd349000 { + compatible = "st,vtac-main"; + reg = <0xfd349000 0x200>, <0xfd320000 0x10000>; + clock-names = "vtac"; + clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>; + }; + + sti-vtac-tx-aux@fd349200 { + compatible = "st,vtac-aux"; + reg = <0xfd349200 0x200>, <0xfd320000 0x10000>; + clock-names = "vtac"; + clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>; + }; + + sti-display-subsystem { + compatible = "st,sti-display-subsystem"; + ranges; + + sti-compositor@fd340000 { + compatible = "st,stih416-compositor"; + reg = <0xfd340000 0x1000>; + clock-names = "compo_main", "compo_aux", + "pix_main", "pix_aux"; + clocks = <&clk_m_a2_div1 CLK_M_COMPO_MAIN>, <&clk_m_a2_div1 CLK_M_COMPO_AUX>, + <&clockgen_c_vcc CLK_S_PIX_MAIN>, <&clockgen_c_vcc CLK_S_PIX_AUX>; + reset-names = "compo-main", "compo-aux"; + resets = <&softreset STIH416_COMPO_M_SOFTRESET>, <&softreset STIH416_COMPO_A_SOFTRESET>; + st,vtg = <&vtg_main>, <&vtg_aux>; + }; + + sti-tvout@fe000000 { + compatible = "st,stih416-tvout"; + reg = <0xfe000000 0x1000>, <0xfe85a000 0x400>, <0xfe830000 0x10000>; + reg-names = "tvout-reg", "hda-reg", "syscfg"; + reset-names = "tvout"; + resets = <&softreset STIH416_HDTVOUT_SOFTRESET>; + }; + + sti-hdmi@fe85c000 { + compatible = "st,stih416-hdmi"; + reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>; + reg-names = "hdmi-reg", "syscfg"; + interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>; + interrupt-names = "irq"; + clock-names = "pix", "tmds", "phy", "audio"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>; + }; + + sti-hda@fe85a000 { + compatible = "st,stih416-hda"; + reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>; + reg-names = "hda-reg", "video-dacs-ctrl"; + clock-names = "pix", "hddac"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>; + }; + + sti-dvo@8d00400 { + compatible = "st,stih407-dvo"; + reg = <0x8d00400 0x200>; + reg-names = "dvo-reg"; + clock-names = "dvo_pix", "dvo", + "main_parent", "aux_parent"; + clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>, + <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dvo>; + sti,panel = <&panel_dvo>; + }; + + sti-hqvdp@9c000000 { + compatible = "st,stih407-hqvdp"; + reg = <0x9C00000 0x100000>; + clock-names = "hqvdp", "pix_main"; + clocks = <&clk_s_c0_flexgen CLK_MAIN_DISP>, <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>; + reset-names = "hqvdp"; + resets = <&softreset STIH407_HDQVDP_SOFTRESET>; + st,vtg = <&vtg_main>; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt new file mode 100644 index 000000000000..e4a25cedc5cf --- /dev/null +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt @@ -0,0 +1,41 @@ +NVIDIA Tegra MIPI pad calibration controller + +Required properties: +- compatible: "nvidia,tegra<chip>-mipi" +- reg: Physical base address and length of the controller's registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mipi-cal +- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads + that need to be calibrated for a given device. + +User nodes need to contain an nvidia,mipi-calibrate property that has a +phandle to refer to the calibration controller node and a bitmask of the pads +that need to be calibrated. + +Example: + + mipi: mipi@700e3000 { + compatible = "nvidia,tegra114-mipi"; + reg = <0x700e3000 0x100>; + clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>; + clock-names = "mipi-cal"; + #nvidia,mipi-calibrate-cells = <1>; + }; + + ... + + host1x@50000000 { + ... + + dsi@54300000 { + ... + + nvidia,mipi-calibrate = <&mipi 0x060>; + + ... + }; + + ... + }; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt new file mode 100644 index 000000000000..a3bd8c050c4e --- /dev/null +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -0,0 +1,380 @@ +NVIDIA Tegra host1x + +Required properties: +- compatible: "nvidia,tegra<chip>-host1x" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. +- #address-cells: The number of cells used to represent physical base addresses + in the host1x address space. Should be 1. +- #size-cells: The number of cells used to represent the size of an address + range in the host1x address space. Should be 1. +- ranges: The mapping of the host1x address space to the CPU address space. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - host1x + +The host1x top-level node defines a number of children, each representing one +of the following host1x client modules: + +- mpe: video encoder + + Required properties: + - compatible: "nvidia,tegra<chip>-mpe" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - mpe + +- vi: video input + + Required properties: + - compatible: "nvidia,tegra<chip>-vi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - vi + +- epp: encoder pre-processor + + Required properties: + - compatible: "nvidia,tegra<chip>-epp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - epp + +- isp: image signal processor + + Required properties: + - compatible: "nvidia,tegra<chip>-isp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - isp + +- gr2d: 2D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr2d" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - 2d + +- gr3d: 3D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr3d" + - reg: Physical base address and length of the controller's registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + (This property may be omitted if the only clock in the list is "3d") + - 3d + This MUST be the first entry. + - 3d2 (Only required on SoCs with two 3D clocks) + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - 3d + - 3d2 (Only required on SoCs with two 3D clocks) + +- dc: display controller + + Required properties: + - compatible: "nvidia,tegra<chip>-dc" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dc + This MUST be the first entry. + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dc + - nvidia,head: The number of the display controller head. This is used to + setup the various types of output to receive video data from the given + head. + + Each display controller node has a child node, named "rgb", that represents + the RGB output associated with the controller. It can take the following + optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel + +- hdmi: High Definition Multimedia Interface + + Required properties: + - compatible: "nvidia,tegra<chip>-hdmi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - hdmi-supply: supply for the +5V HDMI connector pin + - vdd-supply: regulator for supply voltage + - pll-supply: regulator for PLL + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - hdmi + This MUST be the first entry. + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - hdmi + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel + +- tvo: TV encoder output + + Required properties: + - compatible: "nvidia,tegra<chip>-tvo" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +- dsi: display serial interface + + Required properties: + - compatible: "nvidia,tegra<chip>-dsi" + - reg: Physical base address and length of the controller's registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dsi + This MUST be the first entry. + - lp + - parent + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dsi + - avdd-dsi-supply: phandle of a supply that powers the DSI controller + - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying + which pads are used by this DSI output and need to be calibrated. See also + ../display/tegra/nvidia,tegra114-mipi.txt. + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel + - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang + up with in order to support up to 8 data lanes + +- sor: serial output resource + + Required properties: + - compatible: Should be: + - "nvidia,tegra124-sor": for Tegra124 and Tegra132 + - "nvidia,tegra132-sor": for Tegra132 + - "nvidia,tegra210-sor": for Tegra210 + - "nvidia,tegra210-sor1": for Tegra210 + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - sor: clock input for the SOR hardware + - parent: input for the pixel clock + - dp: reference clock for the SOR clock + - safe: safe reference for the SOR clock during power up + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - sor + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel + + Optional properties when driving an eDP output: + - nvidia,dpaux: phandle to a DispayPort AUX interface + +- dpaux: DisplayPort AUX interface + - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise, + must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where + <chip> is tegra132. + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dpaux: clock input for the DPAUX hardware + - parent: reference clock + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dpaux + - vdd-supply: phandle of a supply that powers the DisplayPort link + +Example: + +/ { + ... + + host1x { + compatible = "nvidia,tegra20-host1x", "simple-bus"; + reg = <0x50000000 0x00024000>; + interrupts = <0 65 0x04 /* mpcore syncpt */ + 0 67 0x04>; /* mpcore general */ + clocks = <&tegra_car TEGRA20_CLK_HOST1X>; + resets = <&tegra_car 28>; + reset-names = "host1x"; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x54000000 0x54000000 0x04000000>; + + mpe { + compatible = "nvidia,tegra20-mpe"; + reg = <0x54040000 0x00040000>; + interrupts = <0 68 0x04>; + clocks = <&tegra_car TEGRA20_CLK_MPE>; + resets = <&tegra_car 60>; + reset-names = "mpe"; + }; + + vi { + compatible = "nvidia,tegra20-vi"; + reg = <0x54080000 0x00040000>; + interrupts = <0 69 0x04>; + clocks = <&tegra_car TEGRA20_CLK_VI>; + resets = <&tegra_car 100>; + reset-names = "vi"; + }; + + epp { + compatible = "nvidia,tegra20-epp"; + reg = <0x540c0000 0x00040000>; + interrupts = <0 70 0x04>; + clocks = <&tegra_car TEGRA20_CLK_EPP>; + resets = <&tegra_car 19>; + reset-names = "epp"; + }; + + isp { + compatible = "nvidia,tegra20-isp"; + reg = <0x54100000 0x00040000>; + interrupts = <0 71 0x04>; + clocks = <&tegra_car TEGRA20_CLK_ISP>; + resets = <&tegra_car 23>; + reset-names = "isp"; + }; + + gr2d { + compatible = "nvidia,tegra20-gr2d"; + reg = <0x54140000 0x00040000>; + interrupts = <0 72 0x04>; + clocks = <&tegra_car TEGRA20_CLK_GR2D>; + resets = <&tegra_car 21>; + reset-names = "2d"; + }; + + gr3d { + compatible = "nvidia,tegra20-gr3d"; + reg = <0x54180000 0x00040000>; + clocks = <&tegra_car TEGRA20_CLK_GR3D>; + resets = <&tegra_car 24>; + reset-names = "3d"; + }; + + dc@54200000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54200000 0x00040000>; + interrupts = <0 73 0x04>; + clocks = <&tegra_car TEGRA20_CLK_DISP1>, + <&tegra_car TEGRA20_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 27>; + reset-names = "dc"; + + rgb { + status = "disabled"; + }; + }; + + dc@54240000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54240000 0x00040000>; + interrupts = <0 74 0x04>; + clocks = <&tegra_car TEGRA20_CLK_DISP2>, + <&tegra_car TEGRA20_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 26>; + reset-names = "dc"; + + rgb { + status = "disabled"; + }; + }; + + hdmi { + compatible = "nvidia,tegra20-hdmi"; + reg = <0x54280000 0x00040000>; + interrupts = <0 75 0x04>; + clocks = <&tegra_car TEGRA20_CLK_HDMI>, + <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; + clock-names = "hdmi", "parent"; + resets = <&tegra_car 51>; + reset-names = "hdmi"; + status = "disabled"; + }; + + tvo { + compatible = "nvidia,tegra20-tvo"; + reg = <0x542c0000 0x00040000>; + interrupts = <0 76 0x04>; + clocks = <&tegra_car TEGRA20_CLK_TVO>; + status = "disabled"; + }; + + dsi { + compatible = "nvidia,tegra20-dsi"; + reg = <0x54300000 0x00040000>; + clocks = <&tegra_car TEGRA20_CLK_DSI>, + <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; + clock-names = "dsi", "parent"; + resets = <&tegra_car 48>; + reset-names = "dsi"; + status = "disabled"; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt new file mode 100644 index 000000000000..c30f9ec189ed --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,dra7-dss.txt @@ -0,0 +1,69 @@ +Texas Instruments DRA7x Display Subsystem +========================================= + +See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,dra7-dss" +- reg: address and length of the register spaces for 'dss' +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" +- syscon: phandle to control module core syscon node + +Optional properties: + +Some DRA7xx SoCs have one dedicated video PLL, some have two. These properties +can be used to describe the video PLLs: + +- reg: address and length of the register spaces for 'pll1_clkctrl', + 'pll1', 'pll2_clkctrl', 'pll2' +- clocks: handle to video1 pll clock and video2 pll clock +- clock-names: "video1_clk" and "video2_clk" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,dra7-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + +HDMI +---- + +Required properties: +- compatible: "ti,dra7-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt new file mode 100644 index 000000000000..e1ef29569338 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt @@ -0,0 +1,211 @@ +Texas Instruments OMAP Display Subsystem +======================================== + +Generic Description +------------------- + +This document is a generic description of the OMAP Display Subsystem bindings. +Binding details for each OMAP SoC version are described in respective binding +documentation. + +The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and +a number of encoder modules. All DSS versions contain DSS Core and DISPC, but +the encoder modules vary. + +The DSS Core is the parent of the other DSS modules, and manages clock routing, +integration to the SoC, etc. + +DISPC is the display controller, which reads pixels from the memory and outputs +a RGB pixel stream to encoders. + +The encoder modules encode the received RGB pixel stream to a video output like +HDMI, MIPI DPI, etc. + +Video Ports +----------- + +The DSS Core and the encoders have video port outputs. The structure of the +video ports is described in Documentation/devicetree/bindings/graph.txt, +and the properties for the ports and endpoints for each encoder are +described in the SoC's DSS binding documentation. + +The video ports are used to describe the connections to external hardware, like +panels or external encoders. + +Aliases +------- + +The board dts file may define aliases for displays to assign "displayX" style +name for each display. If no aliases are defined, a semi-random number is used +for the display. + +Example +------- + +A shortened example of the DSS description for OMAP4, with non-relevant parts +removed, defined in omap4.dtsi: + +dss: dss@58000000 { + compatible = "ti,omap4-dss"; + reg = <0x58000000 0x80>; + status = "disabled"; + ti,hwmods = "dss_core"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc@58001000 { + compatible = "ti,omap4-dispc"; + reg = <0x58001000 0x1000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "dss_dispc"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + }; + + hdmi: encoder@58006000 { + compatible = "ti,omap4-hdmi"; + reg = <0x58006000 0x200>, + <0x58006200 0x100>, + <0x58006300 0x100>, + <0x58006400 0x1000>; + reg-names = "wp", "pll", "phy", "core"; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_hdmi"; + clocks = <&dss_48mhz_clk>, <&dss_sys_clk>; + clock-names = "fck", "sys_clk"; + }; +}; + +A shortened example of the board description for OMAP4 Panda board, defined in +omap4-panda.dts. + +The Panda board has a DVI and a HDMI connector, and the board contains a TFP410 +chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level +shifter). The video pipelines for the connectors are formed as follows: + +DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector +OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector + +/ { + aliases { + display0 = &dvi0; + display1 = &hdmi0; + }; + + tfp410: encoder@0 { + compatible = "ti,tfp410"; + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */ + + pinctrl-names = "default"; + pinctrl-0 = <&tfp410_pins>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector@0 { + compatible = "dvi-connector"; + label = "dvi"; + + i2c-bus = <&i2c3>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; + + tpd12s015: encoder@1 { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ + <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ + <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + hdmi0: connector@1 { + compatible = "hdmi-connector"; + label = "hdmi"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; +}; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_out: endpoint { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + }; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&vdac>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt new file mode 100644 index 000000000000..afcd5a86c6a4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,omap2-dss.txt @@ -0,0 +1,54 @@ +Texas Instruments OMAP2 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap2-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" + +Optional nodes: +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap2-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt + + +RFBI +---- + +Required properties: +- compatible: "ti,omap2-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" + + +VENC +---- + +Required properties: +- compatible: "ti,omap2-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC + +VENC Endpoint required properties: + +Required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt new file mode 100644 index 000000000000..dc66e1447c31 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,omap3-dss.txt @@ -0,0 +1,83 @@ +Texas Instruments OMAP3 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap3-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Optional nodes: +- Video ports: + - Port 0: DPI output + - Port 1: SDI output + +DPI Endpoint required properties: +- data-lines: number of lines used + +SDI Endpoint required properties: +- datapairs: number of datapairs used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap3-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap3-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + + +VENC +---- + +Required properties: +- compatible: "ti,omap3-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC +- clocks: handle to fclk +- clock-names: "fck" + +VENC Endpoint required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video + + +DSI +--- + +Required properties: +- compatible: "ti,omap3-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt new file mode 100644 index 000000000000..bc624db8888d --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,omap4-dss.txt @@ -0,0 +1,115 @@ +Texas Instruments OMAP4 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap4-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: RFBI, VENC, DSI, HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap4-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap4-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + +Optional nodes: +- Video port for RFBI output +- RFBI controlled peripherals + + +VENC +---- + +Required properties: +- compatible: "ti,omap4-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC +- clocks: handle to fclk +- clock-names: "fck" + +Optional nodes: +- Video port for VENC output + +VENC Endpoint required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video + + +DSI +--- + +Required properties: +- compatible: "ti,omap4-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" or "dss_dsi2" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for DSI output +- DSI controlled peripherals + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... + + +HDMI +---- + +Required properties: +- compatible: "ti,omap4-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt b/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt new file mode 100644 index 000000000000..118a486c47bb --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,omap5-dss.txt @@ -0,0 +1,96 @@ +Texas Instruments OMAP5 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap5-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: RFBI, DSI, HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap5-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap5-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + +Optional nodes: +- Video port for RFBI output +- RFBI controlled peripherals + + +DSI +--- + +Required properties: +- compatible: "ti,omap5-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" or "dss_dsi2" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for DSI output +- DSI controlled peripherals + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... + + +HDMI +---- + +Required properties: +- compatible: "ti,omap5-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/display/ti/ti,opa362.txt b/Documentation/devicetree/bindings/display/ti/ti,opa362.txt new file mode 100644 index 000000000000..f96083c0bd17 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,opa362.txt @@ -0,0 +1,38 @@ +OPA362 analog video amplifier + +Required properties: +- compatible: "ti,opa362" +- enable-gpios: enable/disable output gpio + +Required node: +- Video port 0 for opa362 input +- Video port 1 for opa362 output + +Example: + +tv_amp: opa362 { + compatible = "ti,opa362"; + enable-gpios = <&gpio1 23 0>; /* GPIO to enable video out amplifier */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + opa_in: endpoint@0 { + remote-endpoint = <&venc_out>; + }; + }; + + port@1 { + reg = <1>; + opa_out: endpoint@0 { + remote-endpoint = <&tv_connector_in>; + }; + }; + }; +}; + + + diff --git a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt b/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt new file mode 100644 index 000000000000..2cbe32a3d0bb --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt @@ -0,0 +1,41 @@ +TFP410 DPI to DVI encoder +========================= + +Required properties: +- compatible: "ti,tfp410" + +Optional properties: +- powerdown-gpios: power-down gpio + +Required nodes: +- Video port 0 for DPI input +- Video port 1 for DVI output + +Example +------- + +tfp410: encoder@0 { + compatible = "ti,tfp410"; + powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/ti/ti,tpd12s015.txt b/Documentation/devicetree/bindings/display/ti/ti,tpd12s015.txt new file mode 100644 index 000000000000..26e6d32e3f20 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ti/ti,tpd12s015.txt @@ -0,0 +1,44 @@ +TPD12S015 HDMI level shifter and ESD protection chip +==================================================== + +Required properties: +- compatible: "ti,tpd12s015" + +Optional properties: +- gpios: CT CP HPD, LS OE and HPD gpios + +Required nodes: +- Video port 0 for HDMI input +- Video port 1 for HDMI output + +Example +------- + +tpd12s015: encoder@1 { + compatible = "ti,tpd12s015"; + + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ + <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ + <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/tilcdc/panel.txt b/Documentation/devicetree/bindings/display/tilcdc/panel.txt new file mode 100644 index 000000000000..f20b31cdc59a --- /dev/null +++ b/Documentation/devicetree/bindings/display/tilcdc/panel.txt @@ -0,0 +1,66 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/display/display-timing.txt for display + timing binding details. + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt new file mode 100644 index 000000000000..a58ae7756fc6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM TFP410 output driver + +Required properties: + - compatible: value should be "ti,tilcdc,tfp410". + - i2c: the phandle for the i2c device to use for DDC + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + - powerdn-gpio: the powerdown GPIO, pulled low to power down the + TFP410 device (for DPMS_OFF) + +Example: + + dvicape { + compatible = "ti,tilcdc,tfp410"; + i2c = <&i2c2>; + pinctrl-names = "default"; + pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; + powerdn-gpio = <&gpio2 31 0>; + }; diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt new file mode 100644 index 000000000000..2136ee81e061 --- /dev/null +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -0,0 +1,56 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be "ti,am33xx-tilcdc". + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + - ti,hwmods: Name of the hwmod associated to the LCDC + +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + +Optional nodes: + + - port/ports: to describe a connection to an external encoder. The + binding follows Documentation/devicetree/bindings/graph.txt and + suppors a single port with a single endpoint. + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; + }; + + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/via,vt8500-fb.txt b/Documentation/devicetree/bindings/display/via,vt8500-fb.txt new file mode 100644 index 000000000000..2871e218a0fb --- /dev/null +++ b/Documentation/devicetree/bindings/display/via,vt8500-fb.txt @@ -0,0 +1,36 @@ +VIA VT8500 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-fb" +- reg : Should contain 1 register ranges(address and length) +- interrupts : framebuffer controller interrupt +- bits-per-pixel : bit depth of framebuffer (16 or 32) + +Required subnodes: +- display-timings: see display-timing.txt for information + +Example: + + fb@d8050800 { + compatible = "via,vt8500-fb"; + reg = <0xd800e400 0x400>; + interrupts = <12>; + bits-per-pixel = <16>; + + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/wm,prizm-ge-rops.txt b/Documentation/devicetree/bindings/display/wm,prizm-ge-rops.txt new file mode 100644 index 000000000000..a850fa011f02 --- /dev/null +++ b/Documentation/devicetree/bindings/display/wm,prizm-ge-rops.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia Graphics Engine Controller +----------------------------------------------------- + +Required properties: +- compatible : "wm,prizm-ge-rops" +- reg : Should contain 1 register ranges(address and length) + +Example: + + ge_rops@d8050400 { + compatible = "wm,prizm-ge-rops"; + reg = <0xd8050400 0x100>; + }; diff --git a/Documentation/devicetree/bindings/display/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/display/wm,wm8505-fb.txt new file mode 100644 index 000000000000..0bcadb2840a5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/wm,wm8505-fb.txt @@ -0,0 +1,33 @@ +Wondermedia WM8505 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "wm,wm8505-fb" +- reg : Should contain 1 register ranges(address and length) +- bits-per-pixel : bit depth of framebuffer (16 or 32) + +Required subnodes: +- display-timings: see display-timing.txt for information + +Example: + + fb@d8051700 { + compatible = "wm,wm8505-fb"; + reg = <0xd8051700 0x200>; + bits-per-pixel = <16>; + + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; + }; |