1 files changed, 0 insertions, 87 deletions
diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
deleted file mode 100644
index 8ec4a7f2623a..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-SN65DSI86 DSI to eDP bridge chip
---------------------------------
-
-This is the binding for Texas Instruments SN65DSI86 bridge.
-http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
-
-Required properties:
-- compatible: Must be "ti,sn65dsi86"
-- reg: i2c address of the chip, 0x2d as per datasheet
-- enable-gpios: gpio specification for bridge_en pin (active high)
-
-- vccio-supply: A 1.8V supply that powers up the digital IOs.
-- vpll-supply: A 1.8V supply that powers up the displayport PLL.
-- vcca-supply: A 1.2V supply that powers up the analog circuits.
-- vcc-supply: A 1.2V supply that powers up the digital core.
-
-Optional properties:
-- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
-
-- gpio-controller: Marks the device has a GPIO controller.
-- #gpio-cells    : Should be two. The first cell is the pin number and
-                   the second cell is used to specify flags.
-                   See ../../gpio/gpio.txt for more information.
-- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
-               the cell formats.
-
-- clock-names: should be "refclk"
-- clocks: Specification for input reference clock. The reference
-	  clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
-
-- data-lanes: See ../../media/video-interface.txt
-- lane-polarities: See ../../media/video-interface.txt
-
-- suspend-gpios: specification for GPIO1 pin on bridge (active low)
-
-Required nodes:
-This device has two video ports. Their connections are modelled using the
-OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for DSI input
-- Video port 1 for eDP output
-
-Example
--------
-
-edp-bridge@2d {
-	compatible = "ti,sn65dsi86";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	reg = <0x2d>;
-
-	enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
-	suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
-
-	interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
-
-	vccio-supply = <&pm8916_l17>;
-	vcca-supply = <&pm8916_l6>;
-	vpll-supply = <&pm8916_l17>;
-	vcc-supply = <&pm8916_l6>;
-
-	clock-names = "refclk";
-	clocks = <&input_refclk>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			edp_bridge_in: endpoint {
-				remote-endpoint = <&dsi_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			edp_bridge_out: endpoint {
-				data-lanes = <2 1 3 0>;
-				lane-polarities = <0 1 0 1>;
-				remote-endpoint = <&edp_panel_in>;
-			};
-		};
-	};
-}