diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/arm,pl11x.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/display/arm,pl11x.txt | 109 |
1 files changed, 109 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt new file mode 100644 index 000000000000..3e3039a8a253 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -0,0 +1,109 @@ +* ARM PrimeCell Color LCD Controller PL110/PL111 + +See also Documentation/devicetree/bindings/arm/primecell.txt + +Required properties: + +- compatible: must be one of: + "arm,pl110", "arm,primecell" + "arm,pl111", "arm,primecell" + +- reg: base address and size of the control registers block + +- interrupt-names: either the single entry "combined" representing a + combined interrupt output (CLCDINTR), or the four entries + "mbe", "vcomp", "lnbu", "fuf" representing the individual + CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts + +- interrupts: contains an interrupt specifier for each entry in + interrupt-names + +- clock-names: should contain "clcdclk" and "apb_pclk" + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/binding/clock/clock-bindings.txt + +Optional properties: + +- memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer + may be located anywhere in the memory + +- max-memory-bandwidth: maximum bandwidth in bytes per second that the + cell's memory interface can handle; if not present, the memory + interface is fast enough to handle all possible video modes + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt; + when it is a TFT panel, the port's endpoint must define the + following property: + + - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values, + defining the way CLD pads are wired up; first value + contains index of the "CLD" external pin (pad) used + as R0 (first bit of the red component), second value + index of the pad used as G0, third value index of the + pad used as B0, see also "LCD panel signal multiplexing + details" paragraphs in the PL110/PL111 Technical + Reference Manuals; this implicitly defines available + color modes, for example: + - PL111 TFT 4:4:4 panel: + arm,pl11x,tft-r0g0b0-pads = <4 15 20>; + - PL110 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <1 7 13>; + - PL111 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 11 19>; + - PL111 TFT 5:6:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 10 19>; + - PL110 and PL111 TFT 8:8:8 panel: + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped: + arm,pl11x,tft-r0g0b0-pads = <16 8 0>; + + +Example: + + clcd@10020000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x10020000 0x1000>; + interrupt-names = "combined"; + interrupts = <0 44 4>; + clocks = <&oscclk1>, <&oscclk2>; + clock-names = "clcdclk", "apb_pclk"; + max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */ + + port { + clcd_pads: endpoint { + remote-endpoint = <&clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; + + }; + + panel { + compatible = "panel-dpi"; + + port { + clcd_panel: endpoint { + remote-endpoint = <&clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <25175000>; + hactive = <640>; + hback-porch = <40>; + hfront-porch = <24>; + hsync-len = <96>; + vactive = <480>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <2>; + }; + }; |