diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm')
37 files changed, 485 insertions, 91 deletions
diff --git a/Documentation/devicetree/bindings/arm/al,alpine.txt b/Documentation/devicetree/bindings/arm/al,alpine.txt new file mode 100644 index 000000000000..f404a4f9b165 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/al,alpine.txt @@ -0,0 +1,88 @@ +Annapurna Labs Alpine Platform Device Tree Bindings +--------------------------------------------------------------- + +Boards in the Alpine family shall have the following properties: + +* Required root node properties: +compatible: must contain "al,alpine" + +* Example: + +/ { + model = "Annapurna Labs Alpine Dev Board"; + compatible = "al,alpine"; + + ... +} + +* CPU node: + +The Alpine platform includes cortex-a15 cores. +enable-method: must be "al,alpine-smp" to allow smp [1] + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + + +* Alpine CPU resume registers + +The CPU resume register are used to define required resume address after +reset. + +Properties: +- compatible : Should contain "al,alpine-cpu-resume". +- reg : Offset and length of the register set for the device + +Example: + +cpu_resume { + compatible = "al,alpine-cpu-resume"; + reg = <0xfbff5ed0 0x30>; +}; + +* Alpine System-Fabric Service Registers + +The System-Fabric Service Registers allow various operation on CPU and +system fabric, like powering CPUs off. + +Properties: +- compatible : Should contain "al,alpine-sysfabric-service" and "syscon". +- reg : Offset and length of the register set for the device + +Example: + +nb_service { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0xfb070000 0x10000>; +}; + +[1] arm/cpu-enable-method/al,alpine-smp diff --git a/Documentation/devicetree/bindings/arm/altera.txt b/Documentation/devicetree/bindings/arm/altera.txt new file mode 100644 index 000000000000..558735aacca8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera.txt @@ -0,0 +1,14 @@ +Altera's SoCFPGA platform device tree bindings +--------------------------------------------- + +Boards with Cyclone 5 SoC: +Required root node properties: +compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + +Boards with Arria 5 SoC: +Required root node properties: +compatible = "altr,socfpga-arria5", "altr,socfpga"; + +Boards with Arria 10 SoC: +Required root node properties: +compatible = "altr,socfpga-arria10", "altr,socfpga"; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 8fe815046140..973884a1bacf 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -8,3 +8,7 @@ Boards with the Amlogic Meson6 SoC shall have the following properties: Boards with the Amlogic Meson8 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8"; + +Board compatible values: + - "geniatech,atv1200" + - "minix,neo-x8" diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 256b4d8bab7b..e774128935d5 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -17,7 +17,10 @@ to deliver its interrupts via SPIs. - interrupts : Interrupt list for secure, non-secure, virtual and hypervisor timers, in that order. -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only where necessary to work around broken firmware which does not configure + CNTFRQ on all CPUs to a uniform correct value. Use of this property is + strongly discouraged; fix your firmware unless absolutely impossible. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. @@ -46,7 +49,8 @@ Example: - compatible : Should at least contain "arm,armv7-timer-mem". -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only when firmware has not configured the MMIO CNTFRQ registers. - reg : The control frame base address. diff --git a/Documentation/devicetree/bindings/arm/armada-39x.txt b/Documentation/devicetree/bindings/arm/armada-39x.txt new file mode 100644 index 000000000000..53d4ff9ea8ad --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-39x.txt @@ -0,0 +1,20 @@ +Marvell Armada 39x Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 39x family shall have the +following property: + +Required root node property: + + - compatible: must contain "marvell,armada390" + +In addition, boards using the Marvell Armada 398 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada398" + +Example: + +compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index ad319f84f560..2e99b5b57350 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -46,10 +46,12 @@ PIT Timer required properties: shared across all System Controller members. System Timer (ST) required properties: -- compatible: Should be "atmel,at91rm9200-st" +- compatible: Should be "atmel,at91rm9200-st", "syscon", "simple-mfd" - reg: Should contain registers location and length - interrupts: Should contain interrupt for the ST which is the IRQ line shared across all System Controller members. +Its subnodes can be: +- watchdog: compatible should be "atmel,at91rm9200-wdt" TC/TCLIB Timer required properties: - compatible: Should be "atmel,<chip>-tcb". diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt index 8240c023e202..8240c023e202 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351.txt index 0ff6560e6094..0ff6560e6094 100644 --- a/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm21664.txt index e0774255e1a6..e0774255e1a6 100644 --- a/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm21664.txt diff --git a/Documentation/devicetree/bindings/arm/bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index ac683480c486..ac683480c486 100644 --- a/Documentation/devicetree/bindings/arm/bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt diff --git a/Documentation/devicetree/bindings/arm/bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt index 6b0f49f6f499..6b0f49f6f499 100644 --- a/Documentation/devicetree/bindings/arm/bcm4708.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt index bd49987a8812..bd49987a8812 100644 --- a/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt diff --git a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index 430608ec09f0..430608ec09f0 100644 --- a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/cygnus.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,cygnus.txt index 4c77169bb534..4c77169bb534 100644 --- a/Documentation/devicetree/bindings/arm/bcm/cygnus.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,cygnus.txt diff --git a/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt b/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt deleted file mode 100644 index 93f31ca1ef4b..000000000000 --- a/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt +++ /dev/null @@ -1,14 +0,0 @@ -Broadcom Kona Family Reset Manager ----------------------------------- - -The reset manager is used on the Broadcom BCM21664 SoC. - -Required properties: - - compatible: brcm,bcm21664-resetmgr - - reg: memory address & range - -Example: - brcm,resetmgr@35001f00 { - compatible = "brcm,bcm21664-resetmgr"; - reg = <0x35001f00 0x24>; - }; diff --git a/Documentation/devicetree/bindings/arm/bcm/kona-timer.txt b/Documentation/devicetree/bindings/arm/bcm/kona-timer.txt deleted file mode 100644 index 39adf54b4388..000000000000 --- a/Documentation/devicetree/bindings/arm/bcm/kona-timer.txt +++ /dev/null @@ -1,25 +0,0 @@ -Broadcom Kona Family timer ------------------------------------------------------ -This timer is used in the following Broadcom SoCs: - BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 - -Required properties: -- compatible : "brcm,kona-timer" -- DEPRECATED: compatible : "bcm,kona-timer" -- reg : Register range for the timer -- interrupts : interrupt for the timer -- clocks: phandle + clock specifier pair of the external clock -- clock-frequency: frequency that the clock operates - -Only one of clocks or clock-frequency should be specified. - -Refer to clocks/clock-bindings.txt for generic clock consumer properties. - -Example: - timer@35006000 { - compatible = "brcm,kona-timer"; - reg = <0x35006000 0x1000>; - interrupts = <0x0 7 0x4>; - clocks = <&hub_timer_clk>; - }; - diff --git a/Documentation/devicetree/bindings/arm/bcm/kona-wdt.txt b/Documentation/devicetree/bindings/arm/bcm/kona-wdt.txt deleted file mode 100644 index 2b86a00e351d..000000000000 --- a/Documentation/devicetree/bindings/arm/bcm/kona-wdt.txt +++ /dev/null @@ -1,15 +0,0 @@ -Broadcom Kona Family Watchdog Timer ------------------------------------ - -This watchdog timer is used in the following Broadcom SoCs: - BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 - -Required properties: - - compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt"; - - reg: memory address & range - -Example: - watchdog@35002f40 { - compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt"; - reg = <0x35002f40 0x6c>; - }; diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index f28d82bbbc56..3c5c631328d3 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -94,8 +94,11 @@ specific to ARM. - compatible Usage: required Value type: <string> - Definition: must be "arm,cci-400-pmu" - + Definition: Must contain one of: + "arm,cci-400-pmu,r0" + "arm,cci-400-pmu,r1" + "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has + secure acces to CCI registers - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index a3089359aaa6..88602b75418e 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -61,7 +61,6 @@ Example: compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0x20010000 0 0x1000>; - coresight-default-sink; clocks = <&oscclk6a>; clock-names = "apb_pclk"; port { diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp new file mode 100644 index 000000000000..c2e0cc5e4cfd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp @@ -0,0 +1,52 @@ +======================================================== +Secondary CPU enable-method "al,alpine-smp" binding +======================================================== + +This document describes the "al,alpine-smp" method for +enabling secondary CPUs. To apply to all CPUs, a single +"al,alpine-smp" enable method should be defined in the +"cpus" node. + +Enable method name: "al,alpine-smp" +Compatible machines: "al,alpine" +Compatible CPUs: "arm,cortex-a15" +Related properties: (none) + +Note: +This enable method requires valid nodes compatible with +"al,alpine-cpu-resume" and "al,alpine-nb-service"[1]. + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + +-- +[1] arm/al,alpine.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 8b9e0a95de31..6aa331d11c5e 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -192,6 +192,7 @@ nodes to be present and contain the properties described below. "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" + "marvell,armada-390-smp" "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 1e097037349c..5da38c5ed476 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -22,6 +22,9 @@ Optional Properties: - pclkN, clkN: Pairs of parent of input clock and input clock to the devices in this power domain. Maximum of 4 pairs (N = 0 to 3) are supported currently. + - asbN: Clocks required by asynchronous bridges (ASB) present in + the power domain. These clock should be enabled during power + domain on/off operations. - power-domains: phandle pointing to the parent power domain, for more details see Documentation/devicetree/bindings/power/power_domain.txt diff --git a/Documentation/devicetree/bindings/arm/geniatech.txt b/Documentation/devicetree/bindings/arm/geniatech.txt deleted file mode 100644 index 74ccba40b73b..000000000000 --- a/Documentation/devicetree/bindings/arm/geniatech.txt +++ /dev/null @@ -1,5 +0,0 @@ -Geniatech platforms device tree bindings -------------------------------------------- - -Geniatech ATV1200 - - compatible = "geniatech,atv1200" diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 1e0d21201d3a..2da059a4790c 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -18,6 +18,8 @@ Main node required properties: "arm,arm11mp-gic" "brcm,brahma-b15-gic" "arm,arm1176jzf-devchip-gic" + "qcom,msm-8660-qgic" + "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 3. diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt index 925ecbf6e7b7..4f40ff3fee4b 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -42,6 +42,7 @@ board. Currently known boards are: "lacie,cloudbox" "lacie,inetspace_v2" "lacie,laplug" +"lacie,nas2big" "lacie,netspace_lite_v2" "lacie,netspace_max_v2" "lacie,netspace_mini_v2" diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt new file mode 100644 index 000000000000..06df04cc827a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt @@ -0,0 +1,84 @@ +QCOM Idle States for cpuidle driver + +ARM provides idle-state node to define the cpuidle states, as defined in [1]. +cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle +states. Idle states have different enter/exit latency and residency values. +The idle states supported by the QCOM SoC are defined as - + + * Standby + * Retention + * Standalone Power Collapse (Standalone PC or SPC) + * Power Collapse (PC) + +Standby: Standby does a little more in addition to architectural clock gating. +When the WFI instruction is executed the ARM core would gate its internal +clocks. In addition to gating the clocks, QCOM cpus use this instruction as a +trigger to execute the SPM state machine. The SPM state machine waits for the +interrupt to trigger the core back in to active. This triggers the cache +hierarchy to enter standby states, when all cpus are idle. An interrupt brings +the SPM state machine out of its wait, the next step is to ensure that the +cache hierarchy is also out of standby, and then the cpu is allowed to resume +execution. This state is defined as a generic ARM WFI state by the ARM cpuidle +driver and is not defined in the DT. The SPM state machine should be +configured to execute this state by default and after executing every other +state below. + +Retention: Retention is a low power state where the core is clock gated and +the memory and the registers associated with the core are retained. The +voltage may be reduced to the minimum value needed to keep the processor +registers active. The SPM should be configured to execute the retention +sequence and would wait for interrupt, before restoring the cpu to execution +state. Retention may have a slightly higher latency than Standby. + +Standalone PC: A cpu can power down and warmboot if there is a sufficient time +between the time it enters idle and the next known wake up. SPC mode is used +to indicate a core entering a power down state without consulting any other +cpu or the system resources. This helps save power only on that core. The SPM +sequence for this idle state is programmed to power down the supply to the +core, wait for the interrupt, restore power to the core, and ensure the +system state including cache hierarchy is ready before allowing core to +resume. Applying power and resetting the core causes the core to warmboot +back into Elevation Level (EL) which trampolines the control back to the +kernel. Entering a power down state for the cpu, needs to be done by trapping +into a EL. Failing to do so, would result in a crash enforced by the warm boot +code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to +be flushed in s/w, before powering down the core. + +Power Collapse: This state is similar to the SPC mode, but distinguishes +itself in that the cpu acknowledges and permits the SoC to enter deeper sleep +modes. In a hierarchical power domain SoC, this means L2 and other caches can +be flushed, system bus, clocks - lowered, and SoC main XO clock gated and +voltages reduced, provided all cpus enter this state. Since the span of low +power modes possible at this state is vast, the exit latency and the residency +of this low power mode would be considered high even though at a cpu level, +this essentially is cpu power down. The SPM in this state also may handshake +with the Resource power manager (RPM) processor in the SoC to indicate a +complete application processor subsystem shut down. + +The idle-state for QCOM SoCs are distinguished by the compatible property of +the idle-states device node. + +The devicetree representation of the idle state should be - + +Required properties: + +- compatible: Must be one of - + "qcom,idle-state-ret", + "qcom,idle-state-spc", + "qcom,idle-state-pc", + and "arm,idle-state". + +Other required and optional properties are specified in [1]. + +Example: + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; + +[1]. Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt index 1505fb8e131a..ae4afc6dcfe0 100644 --- a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt +++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt @@ -2,22 +2,31 @@ SPM AVS Wrapper 2 (SAW2) The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable -micro-controller that transitions a piece of hardware (like a processor or +power-controller that transitions a piece of hardware (like a processor or subsystem) into and out of low power modes via a direct connection to the PMIC. It can also be wired up to interact with other processors in the system, notifying them when a low power state is entered or exited. +Multiple revisions of the SAW hardware are supported using these Device Nodes. +SAW2 revisions differ in the register offset and configuration data. Also, the +same revision of the SAW in different SoCs may have different configuration +data due the the differences in hardware capabilities. Hence the SoC name, the +version of the SAW hardware in that SoC and the distinction between cpu (big +or Little) or cache, may be needed to uniquely identify the SAW register +configuration and initialization data. The compatible string is used to +indicate this parameter. + PROPERTIES - compatible: Usage: required Value type: <string> - Definition: shall contain "qcom,saw2". A more specific value should be - one of: - "qcom,saw2-v1" - "qcom,saw2-v1.1" - "qcom,saw2-v2" - "qcom,saw2-v2.1" + Definition: Must have + "qcom,saw2" + A more specific value could be one of: + "qcom,apq8064-saw2-v1.1-cpu" + "qcom,msm8974-saw2-v2.1-cpu" + "qcom,apq8084-saw2-v2.1-cpu" - reg: Usage: required @@ -26,10 +35,23 @@ PROPERTIES the register region. An optional second element specifies the base address and size of the alias register region. +- regulator: + Usage: optional + Value type: boolean + Definition: Indicates that this SPM device acts as a regulator device + device for the core (CPU or Cache) the SPM is attached + to. -Example: +Example 1: - regulator@2099000 { + power-controller@2099000 { compatible = "qcom,saw2"; reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + +Example 2: + saw0: power-controller@f9089000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/msm/timer.txt b/Documentation/devicetree/bindings/arm/msm/timer.txt index 74607b6c1117..5e10c345548f 100644 --- a/Documentation/devicetree/bindings/arm/msm/timer.txt +++ b/Documentation/devicetree/bindings/arm/msm/timer.txt @@ -9,11 +9,17 @@ Properties: "qcom,scss-timer" - scorpion subsystem - interrupts : Interrupts for the debug timer, the first general purpose - timer, and optionally a second general purpose timer in that - order. + timer, and optionally a second general purpose timer, and + optionally as well, 2 watchdog interrupts, in that order. - reg : Specifies the base address of the timer registers. +- clocks: Reference to the parent clocks, one per output clock. The parents + must appear in the same order as the clock names. + +- clock-names: The name of the clocks as free-form strings. They should be in + the same order as the clocks. + - clock-frequency : The frequency of the debug timer and the general purpose timer(s) in Hz in that order. @@ -29,9 +35,13 @@ Example: compatible = "qcom,scss-timer", "qcom,msm-timer"; interrupts = <1 1 0x301>, <1 2 0x301>, - <1 3 0x301>; + <1 3 0x301>, + <1 4 0x301>, + <1 5 0x301>; reg = <0x0200a000 0x100>; clock-frequency = <19200000>, <32768>; + clocks = <&sleep_clk>; + clock-names = "sleep"; cpu-offset = <0x40000>; }; diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt new file mode 100644 index 000000000000..3a4e5901ce31 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt @@ -0,0 +1,79 @@ +OMAP Control Module bindings + +Control Module contains miscellaneous features under it based on SoC type. +Pincontrol is one common feature, and it has a specialized support +described in [1]. Typically some clock nodes are also under control module. +Syscon is used to share register level access to drivers external to +control module driver itself. + +See [2] for documentation about clock/clockdomain nodes. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +[2] Documentation/devicetree/bindings/clock/ti/* + +Required properties: +- compatible: Must be one of: + "ti,am3-scm" + "ti,am4-scm" + "ti,dm814-scrm" + "ti,dm816-scrm" + "ti,omap2-scm" + "ti,omap3-scm" + "ti,omap4-scm-core" + "ti,omap4-scm-padconf-core" + "ti,omap5-scm-core" + "ti,omap5-scm-padconf-core" + "ti,dra7-scm-core" +- reg: Contains Control Module register address range + (base address and length) + +Optional properties: +- clocks: clocks for this module +- clockdomains: clockdomains for this module + +Examples: + +scm: scm@2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux@30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x230>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; +} + +&scm_clocks { + mcbsp5_mux_fck: mcbsp5_mux_fck { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x02d8>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 974624ea68f6..161448da959d 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,omap5-l3-noc" for OMAP5 family Should be "ti,dra7-l3-noc" for DRA7 family Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. diff --git a/Documentation/devicetree/bindings/arm/omap/l4.txt b/Documentation/devicetree/bindings/arm/omap/l4.txt new file mode 100644 index 000000000000..b4f8a16e7e3b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/l4.txt @@ -0,0 +1,26 @@ +L4 interconnect bindings + +These bindings describe the OMAP SoCs L4 interconnect bus. + +Required properties: +- compatible : Should be "ti,omap2-l4" for OMAP2 family l4 core bus + Should be "ti,omap2-l4-wkup" for OMAP2 family l4 wkup bus + Should be "ti,omap3-l4-core" for OMAP3 family l4 core bus + Should be "ti,omap4-l4-cfg" for OMAP4 family l4 cfg bus + Should be "ti,omap4-l4-wkup" for OMAP4 family l4 wkup bus + Should be "ti,omap5-l4-cfg" for OMAP5 family l4 cfg bus + Should be "ti,omap5-l4-wkup" for OMAP5 family l4 wkup bus + Should be "ti,dra7-l4-cfg" for DRA7 family l4 cfg bus + Should be "ti,dra7-l4-wkup" for DRA7 family l4 wkup bus + Should be "ti,am3-l4-wkup" for AM33xx family l4 wkup bus + Should be "ti,am4-l4-wkup" for AM43xx family l4 wkup bus +- ranges : contains the IO map range for the bus + +Examples: + +l4: l4@48000000 { + compatible "ti,omap2-l4", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x100000>; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/prcm.txt b/Documentation/devicetree/bindings/arm/omap/prcm.txt index 79074dac684a..3eb6d7afff14 100644 --- a/Documentation/devicetree/bindings/arm/omap/prcm.txt +++ b/Documentation/devicetree/bindings/arm/omap/prcm.txt @@ -10,14 +10,10 @@ documentation about the individual clock/clockdomain nodes. Required properties: - compatible: Must be one of: "ti,am3-prcm" - "ti,am3-scrm" "ti,am4-prcm" - "ti,am4-scrm" "ti,omap2-prcm" - "ti,omap2-scrm" "ti,omap3-prm" "ti,omap3-cm" - "ti,omap3-scrm" "ti,omap4-cm1" "ti,omap4-prm" "ti,omap4-cm2" @@ -29,6 +25,8 @@ Required properties: "ti,dra7-prm" "ti,dra7-cm-core-aon" "ti,dra7-cm-core" + "ti,dm814-prcm" + "ti,dm816-prcm" - reg: Contains PRCM module register address range (base address and length) - clocks: clocks for this module diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 75ef91d08f3b..3b5f5d1088c6 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -18,12 +18,21 @@ Required properties: "arm,arm11mpcore-pmu" "arm,arm1176-pmu" "arm,arm1136-pmu" + "qcom,scorpion-pmu" + "qcom,scorpion-mp-pmu" "qcom,krait-pmu" - interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu interrupt (PPI) then 1 interrupt should be specified. Optional properties: +- interrupt-affinity : Valid only when using SPIs, specifies a list of phandles + to CPU nodes corresponding directly to the affinity of + the SPIs listed in the interrupts property. + + This property should be present when there is more than + a single SPI. + - qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd events. diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e51ed2..60d4a1e0a9b5 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; + +- ChipSPARK PopMetal-RK3288 board: + Required root node properties: + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 51147cb5c036..c4f19b2e7dd9 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -7,8 +7,6 @@ SoCs: compatible = "renesas,emev2" - RZ/A1H (R7S72100) compatible = "renesas,r7s72100" - - SH-Mobile AP4 (R8A73720/SH7372) - compatible = "renesas,sh7372" - SH-Mobile AG5 (R8A73A00/SH73A0) compatible = "renesas,sh73a0" - R-Mobile APE6 (R8A73A40) @@ -37,8 +35,6 @@ Boards: compatible = "renesas,alt", "renesas,r8a7794" - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" - - APE6-EVM - Reference Device Tree Implementation - compatible = "renesas,ape6evm-reference", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA compatible = "renesas,armadillo800eva" - BOCK-W @@ -57,12 +53,8 @@ Boards: compatible = "renesas,kzm9d", "renesas,emev2" - Kyoto Microcomputer Co. KZM-A9-GT compatible = "renesas,kzm9g", "renesas,sh73a0" - - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation - compatible = "renesas,kzm9g-reference", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd) - compatible = "renesas,mackerel" - Marzen compatible = "renesas,marzen", "renesas,r8a7779" diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt index 067c9790062f..9a4295b54539 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt @@ -5,9 +5,12 @@ Required properties: Tegra30, must contain "nvidia,tegra30-ahb". Otherwise, must contain '"nvidia,<chip>-ahb", "nvidia,tegra30-ahb"' where <chip> is tegra124, tegra132, or tegra210. -- reg : Should contain 1 register ranges(address and length) +- reg : Should contain 1 register ranges(address and length). For + Tegra20, Tegra30, and Tegra114 chips, the value must be <0x6000c004 + 0x10c>. For Tegra124, Tegra132 and Tegra210 chips, the value should + be be <0x6000c000 0x150>. -Example: +Example (for a Tegra20 chip): ahb: ahb@6000c004 { compatible = "nvidia,tegra20-ahb"; reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */ diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt new file mode 100644 index 000000000000..ea670a5d7ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt @@ -0,0 +1,32 @@ +NVIDIA Tegra Activity Monitor + +The activity monitor block collects statistics about the behaviour of other +components in the system. This information can be used to derive the rate at +which the external memory needs to be clocked in order to serve all requests +from the monitored clients. + +Required properties: +- compatible: should be "nvidia,tegra<chip>-actmon" +- reg: offset and length of the register set for the device +- interrupts: standard interrupt property +- clocks: Must contain a phandle and clock specifier pair for each entry in +clock-names. See ../../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - actmon + - emc +- resets: Must contain an entry for each entry in reset-names. See +../../reset/reset.txt for details. +- reset-names: Must include the following entries: + - actmon + +Example: + actmon@6000c800 { + compatible = "nvidia,tegra124-actmon"; + reg = <0x0 0x6000c800 0x0 0x400>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_ACTMON>, + <&tegra_car TEGRA124_CLK_EMC>; + clock-names = "actmon", "emc"; + resets = <&tegra_car 119>; + reset-names = "actmon"; + }; |