diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm')
| -rw-r--r-- | Documentation/devicetree/bindings/arm/atmel-aic.txt | 38 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/atmel-at91.txt | 92 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/atmel-pmc.txt | 11 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/exynos/power_domain.txt | 21 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/fsl.txt | 22 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/mrvl.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/omap/intc.txt | 27 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/omap/omap.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/spear.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/tegra/emc.txt | 100 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt | 19 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/twd.txt | 48 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/vexpress.txt | 146 |
13 files changed, 544 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt new file mode 100644 index 000000000000..aabca4f83402 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -0,0 +1,38 @@ +* Advanced Interrupt Controller (AIC) + +Required properties: +- compatible: Should be "atmel,<chip>-aic" +- interrupt-controller: Identifies the node as an interrupt controller. +- interrupt-parent: For single AIC system, it is an empty property. +- #interrupt-cells: The number of cells to define the interrupts. It sould be 2. + The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. + Default flag for internal sources should be set to 4 (active high). +- reg: Should contain AIC registers location and length + +Examples: + /* + * AIC + */ + aic: interrupt-controller@fffff000 { + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + interrupt-parent; + #interrupt-cells = <2>; + reg = <0xfffff000 0x200>; + }; + + /* + * An interrupt generating device that is wired to an AIC. + */ + dma: dma-controller@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt new file mode 100644 index 000000000000..ecc81e368715 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -0,0 +1,92 @@ +Atmel AT91 device tree bindings. +================================ + +PIT Timer required properties: +- compatible: Should be "atmel,at91sam9260-pit" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the PIT which is the IRQ line + shared across all System Controller members. + +TC/TCLIB Timer required properties: +- compatible: Should be "atmel,<chip>-pit". + <chip> can be "at91rm9200" or "at91sam9x5" +- reg: Should contain registers location and length +- interrupts: Should contain all interrupts for the TC block + Note that you can specify several interrupt cells if the TC + block has one interrupt per channel. + +Examples: + +One interrupt per TC block: + tcb0: timer@fff7c000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfff7c000 0x100>; + interrupts = <18 4>; + }; + +One interrupt per TC channel in a TC block: + tcb1: timer@fffdc000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffdc000 0x100>; + interrupts = <26 4 27 4 28 4>; + }; + +RSTC Reset Controller required properties: +- compatible: Should be "atmel,<chip>-rstc". + <chip> can be "at91sam9260" or "at91sam9g45" +- reg: Should contain registers location and length + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + +RAMC SDRAM/DDR Controller required properties: +- compatible: Should be "atmel,at91sam9260-sdramc", + "atmel,at91sam9g45-ddramc", +- reg: Should contain registers location and length + For at91sam9263 and at91sam9g45 you must specify 2 entries. + +Examples: + + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + + ramc0: ramc@ffffe400 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe400 0x200 + 0xffffe600 0x200>; + }; + +SHDWC Shutdown Controller + +required properties: +- compatible: Should be "atmel,<chip>-shdwc". + <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". +- reg: Should contain registers location and length + +optional properties: +- atmel,wakeup-mode: String, operation mode of the wakeup mode. + Supported values are: "none", "high", "low", "any". +- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf). + +optional at91sam9260 properties: +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9rl properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9x5 properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt new file mode 100644 index 000000000000..389bed5056e8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt @@ -0,0 +1,11 @@ +* Power Management Controller (PMC) + +Required properties: +- compatible: Should be "atmel,at91rm9200-pmc" +- reg: Should contain PMC registers location and length + +Examples: + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt new file mode 100644 index 000000000000..6528e215c5fe --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -0,0 +1,21 @@ +* Samsung Exynos Power Domains + +Exynos processors include support for multiple power domains which are used +to gate power to one or more peripherals on the processor. + +Required Properties: +- compatiable: should be one of the following. + * samsung,exynos4210-pd - for exynos4210 type power domain. +- reg: physical base address of the controller and length of memory mapped + region. + +Optional Properties: +- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off + state during boot and remains to be turned-off until explicitly turned-on. + +Example: + + lcd0: power-domain-lcd0 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10023C00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 54bdddadf1cf..bfbc771a65f8 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -28,3 +28,25 @@ Required root node properties: i.MX6 Quad SABRE Lite Board Required root node properties: - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; + +Generic i.MX boards +------------------- + +No iomux setup is done for these boards, so this must have been configured +by the bootloader for boards to work with the generic bindings. + +i.MX27 generic board +Required root node properties: + - compatible = "fsl,imx27"; + +i.MX51 generic board +Required root node properties: + - compatible = "fsl,imx51"; + +i.MX53 generic board +Required root node properties: + - compatible = "fsl,imx53"; + +i.MX6q generic board +Required root node properties: + - compatible = "fsl,imx6q"; diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt new file mode 100644 index 000000000000..d8de933e9d81 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl.txt @@ -0,0 +1,6 @@ +Marvell Platforms Device Tree Bindings +---------------------------------------------------- + +PXA168 Aspenite Board +Required root node properties: + - compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168"; diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt new file mode 100644 index 000000000000..f2583e6ec060 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/intc.txt @@ -0,0 +1,27 @@ +* OMAP Interrupt Controller + +OMAP2/3 are using a TI interrupt controller that can support several +configurable number of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,omap2-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,omap2-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <96>; + reg = <0x48200000 0x1000>; + }; + diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index edc618a8aab2..e78e8bccac30 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -41,3 +41,9 @@ Boards: - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" + +- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x + compatible = "ti,omap3-evm", "ti,omap3" + +- AM335X EVM : Software Developement Board for AM335x + compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt new file mode 100644 index 000000000000..f8e54f092328 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear.txt @@ -0,0 +1,8 @@ +ST SPEAr Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST SPEAr600 SoC shall have the following properties: + +Required root node property: + +compatible = "st,spear600"; diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt new file mode 100644 index 000000000000..09335f8eee00 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt @@ -0,0 +1,100 @@ +Embedded Memory Controller + +Properties: +- name : Should be emc +- #address-cells : Should be 1 +- #size-cells : Should be 0 +- compatible : Should contain "nvidia,tegra20-emc". +- reg : Offset and length of the register set for the device +- nvidia,use-ram-code : If present, the sub-nodes will be addressed + and chosen using the ramcode board selector. If omitted, only one + set of tables can be present and said tables will be used + irrespective of ram-code configuration. + +Child device nodes describe the memory settings for different configurations and clock rates. + +Example: + + emc@7000f400 { + #address-cells = < 1 >; + #size-cells = < 0 >; + compatible = "nvidia,tegra20-emc"; + reg = <0x7000f4000 0x200>; + } + + +Embedded Memory Controller ram-code table + +If the emc node has the nvidia,use-ram-code property present, then the +next level of nodes below the emc table are used to specify which settings +apply for which ram-code settings. + +If the emc node lacks the nvidia,use-ram-code property, this level is omitted +and the tables are stored directly under the emc node (see below). + +Properties: + +- name : Should be emc-tables +- nvidia,ram-code : the binary representation of the ram-code board strappings + for which this node (and children) are valid. + + + +Embedded Memory Controller configuration table + +This is a table containing the EMC register settings for the various +operating speeds of the memory controller. They are always located as +subnodes of the emc controller node. + +There are two ways of specifying which tables to use: + +* The simplest is if there is just one set of tables in the device tree, + and they will always be used (based on which frequency is used). + This is the preferred method, especially when firmware can fill in + this information based on the specific system information and just + pass it on to the kernel. + +* The slightly more complex one is when more than one memory configuration + might exist on the system. The Tegra20 platform handles this during + early boot by selecting one out of possible 4 memory settings based + on a 2-pin "ram code" bootstrap setting on the board. The values of + these strappings can be read through a register in the SoC, and thus + used to select which tables to use. + +Properties: +- name : Should be emc-table +- compatible : Should contain "nvidia,tegra20-emc-table". +- reg : either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). +- clock-frequency : the clock frequency for the EMC at which this + table should be used (in kHz). +- nvidia,emc-registers : a 46 word array of EMC registers to be programmed + for operation at the 'clock-frequency' setting. + The order and contents of the registers are: + RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, + WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, + PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, + TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, + ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, + ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, + CFG_CLKTRIM_1, CFG_CLKTRIM_2 + + emc-table@166000 { + reg = <166000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 166000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; + + emc-table@333000 { + reg = <333000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = < 333000 >; + nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 >; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt new file mode 100644 index 000000000000..b5846e21cc2e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra Power Management Controller (PMC) + +Properties: +- name : Should be pmc +- compatible : Should contain "nvidia,tegra<chip>-pmc". +- reg : Offset and length of the register set for the device +- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal. + The PMU is an external Power Management Unit, whose interrupt output + signal is fed into the PMC. This signal is optionally inverted, and then + fed into the ARM GIC. The PMC is not involved in the detection or + handling of this interrupt signal, merely its inversion. + +Example: + +pmc@7000f400 { + compatible = "nvidia,tegra20-pmc"; + reg = <0x7000e400 0x400>; + nvidia,invert-interrupt; +}; diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt new file mode 100644 index 000000000000..75b8610939fa --- /dev/null +++ b/Documentation/devicetree/bindings/arm/twd.txt @@ -0,0 +1,48 @@ +* ARM Timer Watchdog + +ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core +Timer-Watchdog (aka TWD), which provides both a per-cpu local timer +and watchdog. + +The TWD is usually attached to a GIC to deliver its two per-processor +interrupts. + +** Timer node required properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-timer" + "arm,cortex-a5-twd-timer" + "arm,arm11mp-twd-timer" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD timer + register window. + +Example: + + twd-timer@2c000600 { + compatible = "arm,arm11mp-twd-timer""; + reg = <0x2c000600 0x20>; + interrupts = <1 13 0xf01>; + }; + +** Watchdog node properties: + +- compatible : Should be one of: + "arm,cortex-a9-twd-wdt" + "arm,cortex-a5-twd-wdt" + "arm,arm11mp-twd-wdt" + +- interrupts : One interrupt to each core + +- reg : Specify the base address and the size of the TWD watchdog + register window. + +Example: + + twd-watchdog@2c000620 { + compatible = "arm,arm11mp-twd-wdt"; + reg = <0x2c000620 0x20>; + interrupts = <1 14 0xf01>; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt new file mode 100644 index 000000000000..ec8b50cbb2e8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -0,0 +1,146 @@ +ARM Versatile Express boards family +----------------------------------- + +ARM's Versatile Express platform consists of a motherboard and one +or more daughterboards (tiles). The motherboard provides a set of +peripherals. Processor and RAM "live" on the tiles. + +The motherboard and each core tile should be described by a separate +Device Tree source file, with the tile's description including +the motherboard file using a /include/ directive. As the motherboard +can be initialized in one of two different configurations ("memory +maps"), care must be taken to include the correct one. + +Required properties in the root node: +- compatible value: + compatible = "arm,vexpress,<model>", "arm,vexpress"; + where <model> is the full tile model name (as used in the tile's + Technical Reference Manual), eg.: + - for Coretile Express A5x2 (V2P-CA5s): + compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress"; + - for Coretile Express A9x4 (V2P-CA9): + compatible = "arm,vexpress,v2p-ca9", "arm,vexpress"; + If a tile comes in several variants or can be used in more then one + configuration, the compatible value should be: + compatible = "arm,vexpress,<model>,<variant>", \ + "arm,vexpress,<model>", "arm,vexpress"; + eg: + - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1: + compatible = "arm,vexpress,v2p-ca15,tc1", \ + "arm,vexpress,v2p-ca15", "arm,vexpress"; + - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM: + compatible = "arm,vexpress,v2f-2xv6,ca7x3", \ + "arm,vexpress,v2f-2xv6", "arm,vexpress"; + +Optional properties in the root node: +- tile model name (use name from the tile's Technical Reference + Manual, eg. "V2P-CA5s") + model = "<model>"; +- tile's HBI number (unique ARM's board model ID, visible on the + PCB's silkscreen) in hexadecimal transcription: + arm,hbi = <0xhbi> + eg: + - for Coretile Express A5x2 (V2P-CA5s) HBI-0191: + arm,hbi = <0x191>; + - Coretile Express A9x4 (V2P-CA9) HBI-0225: + arm,hbi = <0x225>; + +Top-level standard "cpus" node is required. It must contain a node +with device_type = "cpu" property for every available core, eg.: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + +The motherboard description file provides a single "motherboard" node +using 2 address cells corresponding to the Static Memory Bus used +between the motherboard and the tile. The first cell defines the Chip +Select (CS) line number, the second cell address offset within the CS. +All interrupt lines between the motherboard and the tile are active +high and are described using single cell. + +Optional properties of the "motherboard" node: +- motherboard's memory map variant: + arm,v2m-memory-map = "<name>"; + where name is one of: + - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also + referred to as "ARM Cortex-A Series memory map": + arm,v2m-memory-map = "rs1"; + When this property is missing, the motherboard is using the original + memory map (also known as the "Legacy memory map", primarily used + with the original CoreTile Express A9x4) with peripherals on CS7. + +Motherboard .dtsi files provide a set of labelled peripherals that +can be used to obtain required phandle in the tile's "aliases" node: +- UARTs, note that the numbers correspond to the physical connectors + on the motherboard's back panel: + v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3 +- I2C controllers: + v2m_i2c_dvi and v2m_i2c_pcie +- SP804 timers: + v2m_timer01 and v2m_timer23 + +Current Linux implementation requires a "arm,v2m_timer" alias +pointing at one of the motherboard's SP804 timers, if it is to be +used as the system timer. This alias should be defined in the +motherboard files. + +The tile description must define "ranges", "interrupt-map-mask" and +"interrupt-map" properties to translate the motherboard's address +and interrupt space into one used by the tile's processor. + +Abbreviated example: + +/dts-v1/; + +/ { + model = "V2P-CA5s"; + arm,hbi = <0x225>; + compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <1>; + + chosen { }; + + aliases { + serial0 = &v2m_serial0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a5"; + reg = <0>; + }; + }; + + gic: interrupt-controller@2c001000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x2c001000 0x1000>, + <0x2c000100 0x100>; + }; + + motherboard { + /* CS0 is visible at 0x08000000 */ + ranges = <0 0 0x08000000 0x04000000>; + interrupt-map-mask = <0 0 63>; + /* Active high IRQ 0 is connected to GIC's SPI0 */ + interrupt-map = <0 0 0 &gic 0 0 4>; + }; +}; + +/include/ "vexpress-v2m-rs1.dtsi" |