diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 58 |
1 files changed, 48 insertions, 10 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index ade4e6ec23e0..ec92120a7952 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -511,7 +511,7 @@ 1 -- check protection requested by application. Default value is set via a kernel config option. Value can be changed at runtime via - /selinux/checkreqprot. + /sys/fs/selinux/checkreqprot. cio_ignore= [S390] See Documentation/s390/common_io.rst for details. @@ -1165,10 +1165,10 @@ efi= [EFI] Format: { "old_map", "nochunk", "noruntime", "debug", - "nosoftreserve" } + "nosoftreserve", "disable_early_pci_dma", + "no_disable_early_pci_dma" } old_map [X86-64]: switch to the old ioremap-based EFI - runtime services mapping. 32-bit still uses this one by - default. + runtime services mapping. [Needs CONFIG_X86_UV=y] nochunk: disable reading files in "chunks" in the EFI boot stub, as chunking can cause problems with some firmware implementations. @@ -1180,6 +1180,10 @@ claim. Specify efi=nosoftreserve to disable this reservation and treat the memory by its base type (i.e. EFI_CONVENTIONAL_MEMORY / "System RAM"). + disable_early_pci_dma: Disable the busmaster bit on all + PCI bridges while in the EFI boot stub + no_disable_early_pci_dma: Leave the busmaster bit set + on all PCI bridges while in the EFI boot stub efi_no_storage_paranoia [EFI; X86] Using this parameter you can use more than 50% of @@ -1245,7 +1249,8 @@ 0 -- permissive (log only, no denials). 1 -- enforcing (deny and log). Default value is 0. - Value can be changed at runtime via /selinux/enforce. + Value can be changed at runtime via + /sys/fs/selinux/enforce. erst_disable [ACPI] Disable Error Record Serialization Table (ERST) @@ -1933,9 +1938,31 @@ <cpu number> begins at 0 and the maximum value is "number of CPUs in system - 1". - The format of <cpu-list> is described above. - + managed_irq + + Isolate from being targeted by managed interrupts + which have an interrupt mask containing isolated + CPUs. The affinity of managed interrupts is + handled by the kernel and cannot be changed via + the /proc/irq/* interfaces. + + This isolation is best effort and only effective + if the automatically assigned interrupt mask of a + device queue contains isolated and housekeeping + CPUs. If housekeeping CPUs are online then such + interrupts are directed to the housekeeping CPU + so that IO submitted on the housekeeping CPU + cannot disturb the isolated CPU. + + If a queue's affinity mask contains only isolated + CPUs then this parameter has no effect on the + interrupt routing decision, though interrupts are + only delivered when tasks running on those + isolated CPUs submit IO. IO submitted on + housekeeping CPUs has no influence on those + queues. + The format of <cpu-list> is described above. iucv= [HW,NET] @@ -3978,6 +4005,19 @@ test until boot completes in order to avoid interference. + rcuperf.kfree_rcu_test= [KNL] + Set to measure performance of kfree_rcu() flooding. + + rcuperf.kfree_nthreads= [KNL] + The number of threads running loops of kfree_rcu(). + + rcuperf.kfree_alloc_num= [KNL] + Number of allocations and frees done in an iteration. + + rcuperf.kfree_loops= [KNL] + Number of loops doing rcuperf.kfree_alloc_num number + of allocations and frees. + rcuperf.nreaders= [KNL] Set number of RCU readers. The value -1 selects N, where N is the number of CPUs. A value @@ -4348,9 +4388,7 @@ See security/selinux/Kconfig help text. 0 -- disable. 1 -- enable. - Default value is set via kernel config option. - If enabled at boot time, /selinux/disable can be used - later to disable prior to initial policy load. + Default value is 1. apparmor= [APPARMOR] Disable or enable AppArmor at boot time Format: { "0" | "1" } |