diff options
| -rw-r--r-- | arch/arm/boot/dts/at91-sama5d2_xplained.dts | 70 | ||||
| -rw-r--r-- | arch/arm/boot/dts/sama5d2.dtsi | 73 |
2 files changed, 143 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 5b65ffe0845a..21c780fab761 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -46,6 +46,7 @@ #include "sama5d2.dtsi" #include "sama5d2-pinfunc.h" #include <dt-bindings/mfd/atmel-flexcom.h> +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel SAMA5D2 Xplained"; @@ -71,11 +72,20 @@ ahb { usb0: gadget@00300000 { + atmel,vbus-gpio = <&pioA 31 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; status = "okay"; }; usb1: ohci@00400000 { num-ports = <3>; + atmel,vbus-gpio = <0 /* &pioA 41 GPIO_ACTIVE_HIGH */ + &pioA 42 GPIO_ACTIVE_HIGH + 0 + >; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_default>; status = "okay"; }; @@ -314,6 +324,18 @@ bias-disable; }; + pinctrl_key_gpio_default: key_gpio_default { + pinmux = <PIN_PB9__GPIO>; + bias-pull-up; + }; + + pinctrl_led_gpio_default: led_gpio_default { + pinmux = <PIN_PB0__GPIO>, + <PIN_PB5__GPIO>, + <PIN_PB6__GPIO>; + bias-pull-up; + }; + pinctrl_macb0_default: macb0_default { pinmux = <PIN_PB14__GTXCK>, <PIN_PB15__GTXEN>, @@ -330,6 +352,7 @@ pinctrl_macb0_phy_irq: macb0_phy_irq { pinmux = <PIN_PC9__GPIO>; + bias-disable; }; pinctrl_pdmic_default: pdmic_default { @@ -397,7 +420,54 @@ <PIN_PB12__UTXD3>; bias-disable; }; + + pinctrl_usb_default: usb_default { + pinmux = <PIN_PB10__GPIO>; + bias-disable; + }; + + pinctrl_usba_vbus: usba_vbus { + pinmux = <PIN_PA31__GPIO>; + bias-disable; + }; + }; }; }; + + gpio_keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio_default>; + + bp1 { + label = "PB_USER"; + gpios = <&pioA 41 GPIO_ACTIVE_LOW>; + linux,code = <0x104>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_gpio_default>; + status = "okay"; + + red { + label = "red"; + gpios = <&pioA 38 GPIO_ACTIVE_LOW>; + }; + + green { + label = "green"; + gpios = <&pioA 37 GPIO_ACTIVE_LOW>; + }; + + blue { + label = "blue"; + gpios = <&pioA 32 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; }; diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi index 46dd4308844e..78996bdbd3df 100644 --- a/arch/arm/boot/dts/sama5d2.dtsi +++ b/arch/arm/boot/dts/sama5d2.dtsi @@ -257,6 +257,44 @@ cache-level = <2>; }; + nand0: nand@80000000 { + compatible = "atmel,sama5d2-nand"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + reg = < /* EBI CS3 */ + 0x80000000 0x08000000 + /* SMC PMECC regs */ + 0xf8014070 0x00000490 + /* SMC PMECC Error Location regs */ + 0xf8014500 0x00000200 + /* ROM Galois tables */ + 0x00040000 0x00018000 + >; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH 6>; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + atmel,nand-has-dma; + atmel,has-pmecc; + atmel,pmecc-lookup-table-offset = <0x0 0x8000>; + status = "disabled"; + + nfc@c0000000 { + compatible = "atmel,sama5d4-nfc"; + #address-cells = <1>; + #size-cells = <1>; + reg = < /* NFC Command Registers */ + 0xc0000000 0x08000000 + /* NFC HSMC regs */ + 0xf8014000 0x00000070 + /* NFC SRAM banks */ + 0x00100000 0x00100000 + >; + clocks = <&hsmc_clk>; + atmel,write-by-sram; + }; + }; + sdmmc0: sdio-host@a0000000 { compatible = "atmel,sama5d2-sdhci"; reg = <0xa0000000 0x300>; @@ -874,6 +912,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf801c000 0x100>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(35))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(36))>; + dma-names = "tx", "rx"; clocks = <&uart0_clk>; clock-names = "usart"; status = "disabled"; @@ -883,6 +928,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf8020000 0x100>; interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(37))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(38))>; + dma-names = "tx", "rx"; clocks = <&uart1_clk>; clock-names = "usart"; status = "disabled"; @@ -892,6 +944,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf8024000 0x100>; interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(39))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(40))>; + dma-names = "tx", "rx"; clocks = <&uart2_clk>; clock-names = "usart"; status = "disabled"; @@ -1010,6 +1069,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xfc008000 0x100>; interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(41))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(42))>; + dma-names = "tx", "rx"; clocks = <&uart3_clk>; clock-names = "usart"; status = "disabled"; @@ -1018,6 +1084,13 @@ uart4: serial@fc00c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xfc00c000 0x100>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(43))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(44))>; + dma-names = "tx", "rx"; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>; clocks = <&uart4_clk>; clock-names = "usart"; |