diff options
24 files changed, 1573 insertions, 129 deletions
diff --git a/arch/arm/configs/am3517_evm_defconfig b/arch/arm/configs/am3517_evm_defconfig index 232f8eeb72e3..e4f4fb522bac 100644 --- a/arch/arm/configs/am3517_evm_defconfig +++ b/arch/arm/configs/am3517_evm_defconfig @@ -774,7 +774,57 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_ARMCLCD is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set +# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set +CONFIG_OMAP2_VRAM=y +CONFIG_OMAP2_VRFB=y +CONFIG_OMAP2_DSS=y +CONFIG_OMAP2_VRAM_SIZE=4 +CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y +# CONFIG_OMAP2_DSS_RFBI is not set +CONFIG_OMAP2_DSS_VENC=y +# CONFIG_OMAP2_DSS_SDI is not set +# CONFIG_OMAP2_DSS_DSI is not set +# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set +CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 +CONFIG_FB_OMAP2=y +CONFIG_FB_OMAP2_DEBUG_SUPPORT=y +# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set +CONFIG_FB_OMAP2_NUM_FBS=3 + +# +# OMAP2/3 Display Device Drivers +# +CONFIG_PANEL_GENERIC=y +# CONFIG_PANEL_SHARP_LS037V7DW01 is not set +CONFIG_PANEL_SHARP_LQ043T1DG01=y # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig index a6dd6d1af806..b02e371b0997 100644 --- a/arch/arm/configs/omap3_evm_defconfig +++ b/arch/arm/configs/omap3_evm_defconfig @@ -911,7 +911,56 @@ CONFIG_DAB=y # # CONFIG_VGASTATE is not set CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set +# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set +CONFIG_OMAP2_VRAM=y +CONFIG_OMAP2_VRFB=y +CONFIG_OMAP2_DSS=y +CONFIG_OMAP2_VRAM_SIZE=4 +# CONFIG_OMAP2_DSS_DEBUG_SUPPORT is not set +# CONFIG_OMAP2_DSS_RFBI is not set +CONFIG_OMAP2_DSS_VENC=y +# CONFIG_OMAP2_DSS_SDI is not set +# CONFIG_OMAP2_DSS_DSI is not set +# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set +CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 +CONFIG_FB_OMAP2=y +# CONFIG_FB_OMAP2_DEBUG_SUPPORT is not set +# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set +CONFIG_FB_OMAP2_NUM_FBS=3 + +# +# OMAP2/3 Display Device Drivers +# +CONFIG_PANEL_GENERIC=y +# CONFIG_PANEL_SAMSUNG_LTE430WQ_F0C is not set +CONFIG_PANEL_SHARP_LS037V7DW01=y # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig index 473f9e13f08b..56d4928cd4c9 100644 --- a/arch/arm/configs/rx51_defconfig +++ b/arch/arm/configs/rx51_defconfig @@ -784,6 +784,7 @@ CONFIG_INPUT_KEYBOARD=y # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set CONFIG_KEYBOARD_GPIO=m +CONFIG_KEYBOARD_TWL4030=y # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set @@ -809,6 +810,7 @@ CONFIG_INPUT_MISC=y # CONFIG_INPUT_POWERMATE is not set # CONFIG_INPUT_YEALINK is not set # CONFIG_INPUT_CM109 is not set +CONFIG_INPUT_TWL4030_PWRBUTTON=y CONFIG_INPUT_UINPUT=m # @@ -1110,7 +1112,40 @@ CONFIG_RADIO_ADAPTERS=y # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set +CONFIG_FB=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y + +# Frame buffer hardware drivers +# +CONFIG_OMAP2_VRAM=y +CONFIG_OMAP2_VRFB=y +CONFIG_OMAP2_DSS=y +CONFIG_OMAP2_VRAM_SIZE=0 +# CONFIG_OMAP2_DSS_DEBUG_SUPPORT is not set +# CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS is not set +# CONFIG_OMAP2_DSS_DPI is not set +# CONFIG_OMAP2_DSS_RFBI is not set +# CONFIG_OMAP2_DSS_VENC is not set +CONFIG_OMAP2_DSS_SDI=y +# CONFIG_OMAP2_DSS_DSI is not set +# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set +CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0 +CONFIG_FB_OMAP2=y +CONFIG_FB_OMAP2_DEBUG_SUPPORT=y +CONFIG_FB_OMAP2_NUM_FBS=3 + +# +# OMAP2/3 Display Device Drivers +# +# CONFIG_PANEL_GENERIC is not set +# CONFIG_PANEL_SHARP_LS037V7DW01 is not set +# CONFIG_PANEL_SHARP_LQ043T1DG01 is not set +# CONFIG_PANEL_TOPPOLY_TDO35S is not set +# CONFIG_PANEL_TPO_TD043MTEA1 is not set +CONFIG_PANEL_ACX565AKM=y + # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -1127,6 +1162,8 @@ CONFIG_DISPLAY_SUPPORT=y # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +CONFIG_LOGO=y CONFIG_SOUND=y # CONFIG_SOUND_OSS_CORE is not set CONFIG_SND=y diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index d28e9e5702a0..ea52b034e963 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -119,6 +119,7 @@ obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \ board-rx51-sdram.o \ board-rx51-peripherals.o \ + board-rx51-video.o \ hsmmc.o obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ board-zoom-peripherals.o \ diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 962d377970e9..69b154cdc75d 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -39,6 +39,7 @@ #include <plat/board.h> #include <plat/common.h> +#include <plat/display.h> #include <plat/gpmc.h> #include <plat/nand.h> #include <plat/usb.h> @@ -106,6 +107,77 @@ static struct platform_device omap3beagle_nand_device = { .resource = &omap3beagle_nand_resource, }; +/* DSS */ + +static int beagle_enable_dvi(struct omap_dss_device *dssdev) +{ + if (gpio_is_valid(dssdev->reset_gpio)) + gpio_set_value(dssdev->reset_gpio, 1); + + return 0; +} + +static void beagle_disable_dvi(struct omap_dss_device *dssdev) +{ + if (gpio_is_valid(dssdev->reset_gpio)) + gpio_set_value(dssdev->reset_gpio, 0); +} + +static struct omap_dss_device beagle_dvi_device = { + .type = OMAP_DISPLAY_TYPE_DPI, + .name = "dvi", + .driver_name = "generic_panel", + .phy.dpi.data_lines = 24, + .reset_gpio = 170, + .platform_enable = beagle_enable_dvi, + .platform_disable = beagle_disable_dvi, +}; + +static struct omap_dss_device beagle_tv_device = { + .name = "tv", + .driver_name = "venc", + .type = OMAP_DISPLAY_TYPE_VENC, + .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO, +}; + +static struct omap_dss_device *beagle_dss_devices[] = { + &beagle_dvi_device, + &beagle_tv_device, +}; + +static struct omap_dss_board_info beagle_dss_data = { + .num_devices = ARRAY_SIZE(beagle_dss_devices), + .devices = beagle_dss_devices, + .default_device = &beagle_dvi_device, +}; + +static struct platform_device beagle_dss_device = { + .name = "omapdss", + .id = -1, + .dev = { + .platform_data = &beagle_dss_data, + }, +}; + +static struct regulator_consumer_supply beagle_vdac_supply = + REGULATOR_SUPPLY("vdda_dac", "omapdss"); + +static struct regulator_consumer_supply beagle_vdvi_supply = + REGULATOR_SUPPLY("vdds_dsi", "omapdss"); + +static void __init beagle_display_init(void) +{ + int r; + + r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset"); + if (r < 0) { + printk(KERN_ERR "Unable to get DVI reset GPIO\n"); + return; + } + + gpio_direction_output(beagle_dvi_device.reset_gpio, 0); +} + #include "sdram-micron-mt46h32m32lf-6.h" static struct omap2_hsmmc_info mmc[] = { @@ -117,15 +189,6 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ }; -static struct platform_device omap3_beagle_lcd_device = { - .name = "omap3beagle_lcd", - .id = -1, -}; - -static struct omap_lcd_config omap3_beagle_lcd_config __initdata = { - .ctrl_name = "internal", -}; - static struct regulator_consumer_supply beagle_vmmc1_supply = { .supply = "vmmc", }; @@ -181,16 +244,6 @@ static struct twl4030_gpio_platform_data beagle_gpio_data = { .setup = beagle_twl_gpio_setup, }; -static struct regulator_consumer_supply beagle_vdac_supply = { - .supply = "vdac", - .dev = &omap3_beagle_lcd_device.dev, -}; - -static struct regulator_consumer_supply beagle_vdvi_supply = { - .supply = "vdvi", - .dev = &omap3_beagle_lcd_device.dev, -}; - /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */ static struct regulator_init_data beagle_vmmc1 = { .constraints = { @@ -349,14 +402,8 @@ static struct platform_device keys_gpio = { }, }; -static struct omap_board_config_kernel omap3_beagle_config[] __initdata = { - { OMAP_TAG_LCD, &omap3_beagle_lcd_config }, -}; - static void __init omap3_beagle_init_irq(void) { - omap_board_config = omap3_beagle_config; - omap_board_config_size = ARRAY_SIZE(omap3_beagle_config); omap2_init_common_hw(mt46h32m32lf6_sdrc_params, mt46h32m32lf6_sdrc_params); omap_init_irq(); @@ -367,9 +414,9 @@ static void __init omap3_beagle_init_irq(void) } static struct platform_device *omap3_beagle_devices[] __initdata = { - &omap3_beagle_lcd_device, &leds_gpio, &keys_gpio, + &beagle_dss_device, }; static void __init omap3beagle_flash_init(void) @@ -456,6 +503,8 @@ static void __init omap3_beagle_init(void) /* Ensure SDRC pins are mux'd for self-refresh */ omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT); omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT); + + beagle_display_init(); } static void __init omap3_beagle_map_io(void) diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index 966f5f84f2bd..abdf321c2d41 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -45,6 +45,8 @@ /* list all spi devices here */ enum { RX51_SPI_WL1251, + RX51_SPI_MIPID, /* LCD panel */ + RX51_SPI_TSC2005, /* Touch Controller */ }; static struct wl12xx_platform_data wl1251_pdata; @@ -54,6 +56,16 @@ static struct omap2_mcspi_device_config wl1251_mcspi_config = { .single_channel = 1, }; +static struct omap2_mcspi_device_config mipid_mcspi_config = { + .turbo_mode = 0, + .single_channel = 1, +}; + +static struct omap2_mcspi_device_config tsc2005_mcspi_config = { + .turbo_mode = 0, + .single_channel = 1, +}; + static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { [RX51_SPI_WL1251] = { .modalias = "wl1251", @@ -64,6 +76,22 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { .controller_data = &wl1251_mcspi_config, .platform_data = &wl1251_pdata, }, + [RX51_SPI_MIPID] = { + .modalias = "acx565akm", + .bus_num = 1, + .chip_select = 2, + .max_speed_hz = 6000000, + .controller_data = &mipid_mcspi_config, + }, + [RX51_SPI_TSC2005] = { + .modalias = "tsc2005", + .bus_num = 1, + .chip_select = 0, + /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/ + .max_speed_hz = 6000000, + .controller_data = &tsc2005_mcspi_config, + /* .platform_data = &tsc2005_config,*/ + }, }; #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) diff --git a/arch/arm/mach-omap2/board-rx51-video.c b/arch/arm/mach-omap2/board-rx51-video.c new file mode 100644 index 000000000000..b743a4f42649 --- /dev/null +++ b/arch/arm/mach-omap2/board-rx51-video.c @@ -0,0 +1,109 @@ +/* + * linux/arch/arm/mach-omap2/board-rx51-video.c + * + * Copyright (C) 2010 Nokia + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/mm.h> + +#include <asm/mach-types.h> +#include <plat/mux.h> +#include <plat/display.h> +#include <plat/vram.h> +#include <plat/mcspi.h> + +#include "mux.h" + +#define RX51_LCD_RESET_GPIO 90 + +#if defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) + +static int rx51_lcd_enable(struct omap_dss_device *dssdev) +{ + gpio_set_value(dssdev->reset_gpio, 1); + return 0; +} + +static void rx51_lcd_disable(struct omap_dss_device *dssdev) +{ + gpio_set_value(dssdev->reset_gpio, 0); +} + +static struct omap_dss_device rx51_lcd_device = { + .name = "lcd", + .driver_name = "panel-acx565akm", + .type = OMAP_DISPLAY_TYPE_SDI, + .phy.sdi.datapairs = 2, + .reset_gpio = RX51_LCD_RESET_GPIO, + .platform_enable = rx51_lcd_enable, + .platform_disable = rx51_lcd_disable, +}; + +static struct omap_dss_device *rx51_dss_devices[] = { + &rx51_lcd_device, +}; + +static struct omap_dss_board_info rx51_dss_board_info = { + .num_devices = ARRAY_SIZE(rx51_dss_devices), + .devices = rx51_dss_devices, + .default_device = &rx51_lcd_device, +}; + +struct platform_device rx51_display_device = { + .name = "omapdss", + .id = -1, + .dev = { + .platform_data = &rx51_dss_board_info, + }, +}; + +static struct platform_device *rx51_video_devices[] __initdata = { + &rx51_display_device, +}; + +static int __init rx51_video_init(void) +{ + if (!machine_is_nokia_rx51()) + return 0; + + if (omap_mux_init_gpio(RX51_LCD_RESET_GPIO, OMAP_PIN_OUTPUT)) { + pr_err("%s cannot configure MUX for LCD RESET\n", __func__); + return 0; + } + + if (gpio_request(RX51_LCD_RESET_GPIO, "LCD ACX565AKM reset")) { + pr_err("%s failed to get LCD Reset GPIO\n", __func__); + return 0; + } + + gpio_direction_output(RX51_LCD_RESET_GPIO, 1); + + platform_add_devices(rx51_video_devices, + ARRAY_SIZE(rx51_video_devices)); + return 0; +} + +subsys_initcall(rx51_video_init); + +void __init rx51_video_mem_init(void) +{ + /* + * GFX 864x480x32bpp + * VID1/2 1280x720x32bpp double buffered + */ + omap_vram_set_sdram_vram(PAGE_ALIGN(864 * 480 * 4) + + 2 * PAGE_ALIGN(1280 * 720 * 4 * 2), 0); +} + +#else +void __init rx51_video_mem_init(void) { } +#endif /* defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) */ diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index b155c366c650..1b86b5bb87a2 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -36,6 +36,7 @@ #define RX51_GPIO_SLEEP_IND 162 struct omap_sdrc_params *rx51_get_sdram_timings(void); +extern void rx51_video_mem_init(void); static struct gpio_led gpio_leds[] = { { @@ -143,6 +144,7 @@ static void __init rx51_init(void) static void __init rx51_map_io(void) { omap2_set_globals_343x(); + rx51_video_mem_init(); omap34xx_map_common_io(); } diff --git a/drivers/video/omap2/displays/Kconfig b/drivers/video/omap2/displays/Kconfig index dfb57ee50861..881c9f77c75a 100644 --- a/drivers/video/omap2/displays/Kconfig +++ b/drivers/video/omap2/displays/Kconfig @@ -10,6 +10,7 @@ config PANEL_GENERIC config PANEL_SHARP_LS037V7DW01 tristate "Sharp LS037V7DW01 LCD Panel" depends on OMAP2_DSS + select BACKLIGHT_CLASS_DEVICE help LCD Panel used in TI's SDP3430 and EVM boards @@ -33,8 +34,14 @@ config PANEL_TOPPOLY_TDO35S config PANEL_TPO_TD043MTEA1 tristate "TPO TD043MTEA1 LCD Panel" - depends on OMAP2_DSS && I2C + depends on OMAP2_DSS && SPI help LCD Panel used in OMAP3 Pandora +config PANEL_ACX565AKM + tristate "ACX565AKM Panel" + depends on OMAP2_DSS_SDI + select BACKLIGHT_CLASS_DEVICE + help + This is the LCD panel used on Nokia N900 endmenu diff --git a/drivers/video/omap2/displays/Makefile b/drivers/video/omap2/displays/Makefile index e2bb32168dee..aa386095d7c4 100644 --- a/drivers/video/omap2/displays/Makefile +++ b/drivers/video/omap2/displays/Makefile @@ -5,3 +5,4 @@ obj-$(CONFIG_PANEL_SHARP_LQ043T1DG01) += panel-sharp-lq043t1dg01.o obj-$(CONFIG_PANEL_TAAL) += panel-taal.o obj-$(CONFIG_PANEL_TOPPOLY_TDO35S) += panel-toppoly-tdo35s.o obj-$(CONFIG_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o +obj-$(CONFIG_PANEL_ACX565AKM) += panel-acx565akm.o diff --git a/drivers/video/omap2/displays/panel-acx565akm.c b/drivers/video/omap2/displays/panel-acx565akm.c new file mode 100644 index 000000000000..1f8eb70e2937 --- /dev/null +++ b/drivers/video/omap2/displays/panel-acx565akm.c @@ -0,0 +1,819 @@ +/* + * Support for ACX565AKM LCD Panel used on Nokia N900 + * + * Copyright (C) 2010 Nokia Corporation + * + * Original Driver Author: Imre Deak <imre.deak@nokia.com> + * Based on panel-generic.c by Tomi Valkeinen <tomi.valkeinen@nokia.com> + * Adapted to new DSS2 framework: Roger Quadros <roger.quadros@nokia.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/spi/spi.h> +#include <linux/jiffies.h> +#include <linux/sched.h> +#include <linux/backlight.h> +#include <linux/fb.h> + +#include <plat/display.h> + +#define MIPID_CMD_READ_DISP_ID 0x04 +#define MIPID_CMD_READ_RED 0x06 +#define MIPID_CMD_READ_GREEN 0x07 +#define MIPID_CMD_READ_BLUE 0x08 +#define MIPID_CMD_READ_DISP_STATUS 0x09 +#define MIPID_CMD_RDDSDR 0x0F +#define MIPID_CMD_SLEEP_IN 0x10 +#define MIPID_CMD_SLEEP_OUT 0x11 +#define MIPID_CMD_DISP_OFF 0x28 +#define MIPID_CMD_DISP_ON 0x29 +#define MIPID_CMD_WRITE_DISP_BRIGHTNESS 0x51 +#define MIPID_CMD_READ_DISP_BRIGHTNESS 0x52 +#define MIPID_CMD_WRITE_CTRL_DISP 0x53 + +#define CTRL_DISP_BRIGHTNESS_CTRL_ON (1 << 5) +#define CTRL_DISP_AMBIENT_LIGHT_CTRL_ON (1 << 4) +#define CTRL_DISP_BACKLIGHT_ON (1 << 2) +#define CTRL_DISP_AUTO_BRIGHTNESS_ON (1 << 1) + +#define MIPID_CMD_READ_CTRL_DISP 0x54 +#define MIPID_CMD_WRITE_CABC 0x55 +#define MIPID_CMD_READ_CABC 0x56 + +#define MIPID_VER_LPH8923 3 +#define MIPID_VER_LS041Y3 4 +#define MIPID_VER_L4F00311 8 +#define MIPID_VER_ACX565AKM 9 + +struct acx565akm_device { + char *name; + int enabled; + int model; + int revision; + u8 display_id[3]; + unsigned has_bc:1; + unsigned has_cabc:1; + unsigned cabc_mode; + unsigned long hw_guard_end; /* next value of jiffies + when we can issue the + next sleep in/out command */ + unsigned long hw_guard_wait; /* max guard time in jiffies */ + + struct spi_device *spi; + struct mutex mutex; + + struct omap_dss_device *dssdev; + struct backlight_device *bl_dev; +}; + +static struct acx565akm_device acx_dev; +static int acx565akm_bl_update_status(struct backlight_device *dev); + +/*--------------------MIPID interface-----------------------------*/ + +static void acx565akm_transfer(struct acx565akm_device *md, int cmd, + const u8 *wbuf, int wlen, u8 *rbuf, int rlen) +{ + struct spi_message m; + struct spi_transfer *x, xfer[5]; + int r; + + BUG_ON(md->spi == NULL); + + spi_message_init(&m); + + memset(xfer, 0, sizeof(xfer)); + x = &xfer[0]; + + cmd &= 0xff; + x->tx_buf = &cmd; + x->bits_per_word = 9; + x->len = 2; + + if (rlen > 1 && wlen == 0) { + /* + * Between the command and the response data there is a + * dummy clock cycle. Add an extra bit after the command + * word to account for this. + */ + x->bits_per_word = 10; + cmd <<= 1; + } + spi_message_add_tail(x, &m); + + if (wlen) { + x++; + x->tx_buf = wbuf; + x->len = wlen; + x->bits_per_word = 9; + spi_message_add_tail(x, &m); + } + + if (rlen) { + x++; + x->rx_buf = rbuf; + x->len = rlen; + spi_message_add_tail(x, &m); + } + + r = spi_sync(md->spi, &m); + if (r < 0) + dev_dbg(&md->spi->dev, "spi_sync %d\n", r); +} + +static inline void acx565akm_cmd(struct acx565akm_device *md, int cmd) +{ + acx565akm_transfer(md, cmd, NULL, 0, NULL, 0); +} + +static inline void acx565akm_write(struct acx565akm_device *md, + int reg, const u8 *buf, int len) +{ + acx565akm_transfer(md, reg, buf, len, NULL, 0); +} + +static inline void acx565akm_read(struct acx565akm_device *md, + int reg, u8 *buf, int len) +{ + acx565akm_transfer(md, reg, NULL, 0, buf, len); +} + +static void hw_guard_start(struct acx565akm_device *md, int guard_msec) +{ + md->hw_guard_wait = msecs_to_jiffies(guard_msec); + md->hw_guard_end = jiffies + md->hw_guard_wait; +} + +static void hw_guard_wait(struct acx565akm_device *md) +{ + unsigned long wait = md->hw_guard_end - jiffies; + + if ((long)wait > 0 && wait <= md->hw_guard_wait) { + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(wait); + } +} + +/*----------------------MIPID wrappers----------------------------*/ + +static void set_sleep_mode(struct acx565akm_device *md, int on) +{ + int cmd; + + if (on) + cmd = MIPID_CMD_SLEEP_IN; + else + cmd = MIPID_CMD_SLEEP_OUT; + /* + * We have to keep 120msec between sleep in/out commands. + * (8.2.15, 8.2.16). + */ + hw_guard_wait(md); + acx565akm_cmd(md, cmd); + hw_guard_start(md, 120); +} + +static void set_display_state(struct acx565akm_device *md, int enabled) +{ + int cmd = enabled ? MIPID_CMD_DISP_ON : MIPID_CMD_DISP_OFF; + + acx565akm_cmd(md, cmd); +} + +static int panel_enabled(struct acx565akm_device *md) +{ + u32 disp_status; + int enabled; + + acx565akm_read(md, MIPID_CMD_READ_DISP_STATUS, (u8 *)&disp_status, 4); + disp_status = __be32_to_cpu(disp_status); + enabled = (disp_status & (1 << 17)) && (disp_status & (1 << 10)); + dev_dbg(&md->spi->dev, + "LCD panel %senabled by bootloader (status 0x%04x)\n", + enabled ? "" : "not ", disp_status); + return enabled; +} + +static int panel_detect(struct acx565akm_device *md) +{ + acx565akm_read(md, MIPID_CMD_READ_DISP_ID, md->display_id, 3); + dev_dbg(&md->spi->dev, "MIPI display ID: %02x%02x%02x\n", + md->display_id[0], md->display_id[1], md->display_id[2]); + + switch (md->display_id[0]) { + case 0x10: + md->model = MIPID_VER_ACX565AKM; + md->name = "acx565akm"; + md->has_bc = 1; + md->has_cabc = 1; + break; + case 0x29: + md->model = MIPID_VER_L4F00311; + md->name = "l4f00311"; + break; + case 0x45: + md->model = MIPID_VER_LPH8923; + md->name = "lph8923"; + break; + case 0x83: + md->model = MIPID_VER_LS041Y3; + md->name = "ls041y3"; + break; + default: + md->name = "unknown"; + dev_err(&md->spi->dev, "invalid display ID\n"); + return -ENODEV; + } + + md->revision = md->display_id[1]; + + dev_info(&md->spi->dev, "omapfb: %s rev %02x LCD detected\n", + md->name, md->revision); + + return 0; +} + +/*----------------------Backlight Control-------------------------*/ + +static void enable_backlight_ctrl(struct acx565akm_device *md, int enable) +{ + u16 ctrl; + + acx565akm_read(md, MIPID_CMD_READ_CTRL_DISP, (u8 *)&ctrl, 1); + if (enable) { + ctrl |= CTRL_DISP_BRIGHTNESS_CTRL_ON | + CTRL_DISP_BACKLIGHT_ON; + } else { + ctrl &= ~(CTRL_DISP_BRIGHTNESS_CTRL_ON | + CTRL_DISP_BACKLIGHT_ON); + } + + ctrl |= 1 << 8; + acx565akm_write(md, MIPID_CMD_WRITE_CTRL_DISP, (u8 *)&ctrl, 2); +} + +static void set_cabc_mode(struct acx565akm_device *md, unsigned mode) +{ + u16 cabc_ctrl; + + md->cabc_mode = mode; + if (!md->enabled) + return; + cabc_ctrl = 0; + acx565akm_read(md, MIPID_CMD_READ_CABC, (u8 *)&cabc_ctrl, 1); + cabc_ctrl &= ~3; + cabc_ctrl |= (1 << 8) | (mode & 3); + acx565akm_write(md, MIPID_CMD_WRITE_CABC, (u8 *)&cabc_ctrl, 2); +} + +static unsigned get_cabc_mode(struct acx565akm_device *md) +{ + return md->cabc_mode; +} + +static unsigned get_hw_cabc_mode(struct acx565akm_device *md) +{ + u8 cabc_ctrl; + + acx565akm_read(md, MIPID_CMD_READ_CABC, &cabc_ctrl, 1); + return cabc_ctrl & 3; +} + +static void acx565akm_set_brightness(struct acx565akm_device *md, int level) +{ + int bv; + + bv = level | (1 << 8); + acx565akm_write(md, MIPID_CMD_WRITE_DISP_BRIGHTNESS, (u8 *)&bv, 2); + + if (level) + enable_backlight_ctrl(md, 1); + else + enable_backlight_ctrl(md, 0); +} + +static int acx565akm_get_actual_brightness(struct acx565akm_device *md) +{ + u8 bv; + + acx565akm_read(md, MIPID_CMD_READ_DISP_BRIGHTNESS, &bv, 1); + + return bv; +} + + +static int acx565akm_bl_update_status(struct backlight_device *dev) +{ + struct acx565akm_device *md = dev_get_drvdata(&dev->dev); + int r; + int level; + + dev_dbg(&md->spi->dev, "%s\n", __func__); + + mutex_lock(&md->mutex); + + if (dev->props.fb_blank == FB_BLANK_UNBLANK && + dev->props.power == FB_BLANK_UNBLANK) + level = dev->props.brightness; + else + level = 0; + + r = 0; + if (md->has_bc) + acx565akm_set_brightness(md, level); + else if (md->dssdev->set_backlight) + r = md->dssdev->set_backlight(md->dssdev, level); + else + r = -ENODEV; + + mutex_unlock(&md->mutex); + + return r; +} + +static int acx565akm_bl_get_intensity(struct backlight_device *dev) +{ + struct acx565akm_device *md = dev_get_drvdata(&dev->dev); + + dev_dbg(&dev->dev, "%s\n", __func__); + + if (!md->has_bc && md->dssdev->set_backlight == NULL) + return -ENODEV; + + if (dev->props.fb_blank == FB_BLANK_UNBLANK && + dev->props.power == FB_BLANK_UNBLANK) { + if (md->has_bc) + return acx565akm_get_actual_brightness(md); + else + return dev->props.brightness; + } + + return 0; +} + +static const struct backlight_ops acx565akm_bl_ops = { + .get_brightness = acx565akm_bl_get_intensity, + .update_status = acx565akm_bl_update_status, +}; + +/*--------------------Auto Brightness control via Sysfs---------------------*/ + +static const char *cabc_modes[] = { + "off", /* always used when CABC is not supported */ + "ui", + "still-image", + "moving-image", +}; + +static ssize_t show_cabc_mode(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct acx565akm_device *md = dev_get_drvdata(dev); + const char *mode_str; + int mode; + int len; + + if (!md->has_cabc) + mode = 0; + else + mode = get_cabc_mode(md); + mode_str = "unknown"; + if (mode >= 0 && mode < ARRAY_SIZE(cabc_modes)) + mode_str = cabc_modes[mode]; + len = snprintf(buf, PAGE_SIZE, "%s\n", mode_str); + + return len < PAGE_SIZE - 1 ? len : PAGE_SIZE - 1; +} + +static ssize_t store_cabc_mode(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct acx565akm_device *md = dev_get_drvdata(dev); + int i; + + for (i = 0; i < ARRAY_SIZE(cabc_modes); i++) { + const char *mode_str = cabc_modes[i]; + int cmp_len = strlen(mode_str); + + if (count > 0 && buf[count - 1] == '\n') + count--; + if (count != cmp_len) + continue; + + if (strncmp(buf, mode_str, cmp_len) == 0) + break; + } + + if (i == ARRAY_SIZE(cabc_modes)) + return -EINVAL; + + if (!md->has_cabc && i != 0) + return -EINVAL; + + mutex_lock(&md->mutex); + set_cabc_mode(md, i); + mutex_unlock(&md->mutex); + + return count; +} + +static ssize_t show_cabc_available_modes(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct acx565akm_device *md = dev_get_drvdata(dev); + int len; + int i; + + if (!md->has_cabc) + return snprintf(buf, PAGE_SIZE, "%s\n", cabc_modes[0]); + + for (i = 0, len = 0; + len < PAGE_SIZE && i < ARRAY_SIZE(cabc_modes); i++) + len += snprintf(&buf[len], PAGE_SIZE - len, "%s%s%s", + i ? " " : "", cabc_modes[i], + i == ARRAY_SIZE(cabc_modes) - 1 ? "\n" : ""); + + return len < PAGE_SIZE ? len : PAGE_SIZE - 1; +} + +static DEVICE_ATTR(cabc_mode, S_IRUGO | S_IWUSR, + show_cabc_mode, store_cabc_mode); +static DEVICE_ATTR(cabc_available_modes, S_IRUGO, + show_cabc_available_modes, NULL); + +static struct attribute *bldev_attrs[] = { + &dev_attr_cabc_mode.attr, + &dev_attr_cabc_available_modes.attr, + NULL, +}; + +static struct attribute_group bldev_attr_group = { + .attrs = bldev_attrs, +}; + + +/*---------------------------ACX Panel----------------------------*/ + +static int acx_get_recommended_bpp(struct omap_dss_device *dssdev) +{ + return 16; +} + +static struct omap_video_timings acx_panel_timings = { + .x_res = 800, + .y_res = 480, + .pixel_clock = 24000, + .hfp = 28, + .hsw = 4, + .hbp = 24, + .vfp = 3, + .vsw = 3, + .vbp = 4, +}; + +static int acx_panel_probe(struct omap_dss_device *dssdev) +{ + int r; + struct acx565akm_device *md = &acx_dev; + struct backlight_device *bldev; + int max_brightness, brightness; + struct backlight_properties props; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + dssdev->panel.config = OMAP_DSS_LCD_TFT | OMAP_DSS_LCD_IVS | + OMAP_DSS_LCD_IHS; + /* FIXME AC bias ? */ + dssdev->panel.timings = acx_panel_timings; + + if (dssdev->platform_enable) + dssdev->platform_enable(dssdev); + /* + * After reset we have to wait 5 msec before the first + * command can be sent. + */ + msleep(5); + + md->enabled = panel_enabled(md); + + r = panel_detect(md); + if (r) { + dev_err(&dssdev->dev, "%s panel detect error\n", __func__); + if (!md->enabled && dssdev->platform_disable) + dssdev->platform_disable(dssdev); + return r; + } + + mutex_lock(&acx_dev.mutex); + acx_dev.dssdev = dssdev; + mutex_unlock(&acx_dev.mutex); + + if (!md->enabled) { + if (dssdev->platform_disable) + dssdev->platform_disable(dssdev); + } + + /*------- Backlight control --------*/ + + props.fb_blank = FB_BLANK_UNBLANK; + props.power = FB_BLANK_UNBLANK; + + bldev = backlight_device_register("acx565akm", &md->spi->dev, + md, &acx565akm_bl_ops, &props); + md->bl_dev = bldev; + if (md->has_cabc) { + r = sysfs_create_group(&bldev->dev.kobj, &bldev_attr_group); + if (r) { + dev_err(&bldev->dev, + "%s failed to create sysfs files\n", __func__); + backlight_device_unregister(bldev); + return r; + } + md->cabc_mode = get_hw_cabc_mode(md); + } + + if (md->has_bc) + max_brightness = 255; + else + max_brightness = dssdev->max_backlight_level; + + if (md->has_bc) + brightness = acx565akm_get_actual_brightness(md); + else if (dssdev->get_backlight) + brightness = dssdev->get_backlight(dssdev); + else + brightness = 0; + + bldev->props.max_brightness = max_brightness; + bldev->props.brightness = brightness; + + acx565akm_bl_update_status(bldev); + return 0; +} + +static void acx_panel_remove(struct omap_dss_device *dssdev) +{ + struct acx565akm_device *md = &acx_dev; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + sysfs_remove_group(&md->bl_dev->dev.kobj, &bldev_attr_group); + backlight_device_unregister(md->bl_dev); + mutex_lock(&acx_dev.mutex); + acx_dev.dssdev = NULL; + mutex_unlock(&acx_dev.mutex); +} + +static int acx_panel_power_on(struct omap_dss_device *dssdev) +{ + struct acx565akm_device *md = &acx_dev; + int r; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + + mutex_lock(&md->mutex); + + r = omapdss_sdi_display_enable(dssdev); + if (r) { + pr_err("%s sdi enable failed\n", __func__); + return r; + } + + /*FIXME tweak me */ + msleep(50); + + if (dssdev->platform_enable) { + r = dssdev->platform_enable(dssdev); + if (r) + goto fail; + } + + if (md->enabled) { + dev_dbg(&md->spi->dev, "panel already enabled\n"); + mutex_unlock(&md->mutex); + return 0; + } + + /* + * We have to meet all the following delay requirements: + * 1. tRW: reset pulse width 10usec (7.12.1) + * 2. tRT: reset cancel time 5msec (7.12.1) + * 3. Providing PCLK,HS,VS signals for 2 frames = ~50msec worst + * case (7.6.2) + * 4. 120msec before the sleep out command (7.12.1) + */ + msleep(120); + + set_sleep_mode(md, 0); + md->enabled = 1; + + /* 5msec between sleep out and the next command. (8.2.16) */ + msleep(5); + set_display_state(md, 1); + set_cabc_mode(md, md->cabc_mode); + + mutex_unlock(&md->mutex); + + return acx565akm_bl_update_status(md->bl_dev); +fail: + omapdss_sdi_display_disable(dssdev); + return r; +} + +static void acx_panel_power_off(struct omap_dss_device *dssdev) +{ + struct acx565akm_device *md = &acx_dev; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + + mutex_lock(&md->mutex); + + if (!md->enabled) { + mutex_unlock(&md->mutex); + return; + } + set_display_state(md, 0); + set_sleep_mode(md, 1); + md->enabled = 0; + /* + * We have to provide PCLK,HS,VS signals for 2 frames (worst case + * ~50msec) after sending the sleep in command and asserting the + * reset signal. We probably could assert the reset w/o the delay + * but we still delay to avoid possible artifacts. (7.6.1) + */ + msleep(50); + + if (dssdev->platform_disable) + dssdev->platform_disable(dssdev); + + /* FIXME need to tweak this delay */ + msleep(100); + + omapdss_sdi_display_disable(dssdev); + + mutex_unlock(&md->mutex); +} + +static int acx_panel_enable(struct omap_dss_device *dssdev) +{ + int r; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + r = acx_panel_power_on(dssdev); + + if (r) + return r; + + dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; + return 0; +} + +static void acx_panel_disable(struct omap_dss_device *dssdev) +{ + dev_dbg(&dssdev->dev, "%s\n", __func__); + acx_panel_power_off(dssdev); + dssdev->state = OMAP_DSS_DISPLAY_DISABLED; +} + +static int acx_panel_suspend(struct omap_dss_device *dssdev) +{ + dev_dbg(&dssdev->dev, "%s\n", __func__); + acx_panel_power_off(dssdev); + dssdev->state = OMAP_DSS_DISPLAY_SUSPENDED; + return 0; +} + +static int acx_panel_resume(struct omap_dss_device *dssdev) +{ + int r; + + dev_dbg(&dssdev->dev, "%s\n", __func__); + r = acx_panel_power_on(dssdev); + if (r) + return r; + + dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; + return 0; +} + +static void acx_panel_set_timings(struct omap_dss_device *dssdev, + struct omap_video_timings *timings) +{ + int r; + + if (dssdev->state == OMAP_DSS_DISPLAY_ACTIVE) + omapdss_sdi_display_disable(dssdev); + + dssdev->panel.timings = *timings; + + if (dssdev->state == OMAP_DSS_DISPLAY_ACTIVE) { + r = omapdss_sdi_display_enable(dssdev); + if (r) + dev_err(&dssdev->dev, "%s enable failed\n", __func__); + } +} + +static void acx_panel_get_timings(struct omap_dss_device *dssdev, + struct omap_video_timings *timings) +{ + *timings = dssdev->panel.timings; +} + +static int acx_panel_check_timings(struct omap_dss_device *dssdev, + struct omap_video_timings *timings) +{ + return 0; +} + + +static struct omap_dss_driver acx_panel_driver = { + .probe = acx_panel_probe, + .remove = acx_panel_remove, + + .enable = acx_panel_enable, + .disable = acx_panel_disable, + .suspend = acx_panel_suspend, + .resume = acx_panel_resume, + + .set_timings = acx_panel_set_timings, + .get_timings = acx_panel_get_timings, + .check_timings = acx_panel_check_timings, + + .get_recommended_bpp = acx_get_recommended_bpp, + + .driver = { + .name = "panel-acx565akm", + .owner = THIS_MODULE, + }, +}; + +/*--------------------SPI probe-------------------------*/ + +static int acx565akm_spi_probe(struct spi_device *spi) +{ + struct acx565akm_device *md = &acx_dev; + + dev_dbg(&spi->dev, "%s\n", __func__); + + spi->mode = SPI_MODE_3; + md->spi = spi; + mutex_init(&md->mutex); + dev_set_drvdata(&spi->dev, md); + + omap_dss_register_driver(&acx_panel_driver); + + return 0; +} + +static int acx565akm_spi_remove(struct spi_device *spi) +{ + struct acx565akm_device *md = dev_get_drvdata(&spi->dev); + + dev_dbg(&md->spi->dev, "%s\n", __func__); + omap_dss_unregister_driver(&acx_panel_driver); + + return 0; +} + +static struct spi_driver acx565akm_spi_driver = { + .driver = { + .name = "acx565akm", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = acx565akm_spi_probe, + .remove = __devexit_p(acx565akm_spi_remove), +}; + +static int __init acx565akm_init(void) +{ + return spi_register_driver(&acx565akm_spi_driver); +} + +static void __exit acx565akm_exit(void) +{ + spi_unregister_driver(&acx565akm_spi_driver); +} + +module_init(acx565akm_init); +module_exit(acx565akm_exit); + +MODULE_AUTHOR("Nokia Corporation"); +MODULE_DESCRIPTION("acx565akm LCD Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/video/omap2/displays/panel-sharp-ls037v7dw01.c b/drivers/video/omap2/displays/panel-sharp-ls037v7dw01.c index 8d51a5e6341c..7d9eb2b1f5af 100644 --- a/drivers/video/omap2/displays/panel-sharp-ls037v7dw01.c +++ b/drivers/video/omap2/displays/panel-sharp-ls037v7dw01.c @@ -20,10 +20,17 @@ #include <linux/module.h> #include <linux/delay.h> #include <linux/device.h> +#include <linux/backlight.h> +#include <linux/fb.h> #include <linux/err.h> +#include <linux/slab.h> #include <plat/display.h> +struct sharp_data { + struct backlight_device *bl; +}; + static struct omap_video_timings sharp_ls_timings = { .x_res = 480, .y_res = 640, @@ -39,18 +46,89 @@ static struct omap_video_timings sharp_ls_timings = { .vbp = 1, }; +static int sharp_ls_bl_update_status(struct backlight_device *bl) +{ + struct omap_dss_device *dssdev = dev_get_drvdata(&bl->dev); + int level; + + if (!dssdev->set_backlight) + return -EINVAL; + + if (bl->props.fb_blank == FB_BLANK_UNBLANK && + bl->props.power == FB_BLANK_UNBLANK) + level = bl->props.brightness; + else + level = 0; + + return dssdev->set_backlight(dssdev, level); +} + +static int sharp_ls_bl_get_brightness(struct backlight_device *bl) +{ + if (bl->props.fb_blank == FB_BLANK_UNBLANK && + bl->props.power == FB_BLANK_UNBLANK) + return bl->props.brightness; + + return 0; +} + +static const struct backlight_ops sharp_ls_bl_ops = { + .get_brightness = sharp_ls_bl_get_brightness, + .update_status = sharp_ls_bl_update_status, +}; + + + static int sharp_ls_panel_probe(struct omap_dss_device *dssdev) { + struct backlight_properties props; + struct backlight_device *bl; + struct sharp_data *sd; + int r; + dssdev->panel.config = OMAP_DSS_LCD_TFT | OMAP_DSS_LCD_IVS | OMAP_DSS_LCD_IHS; dssdev->panel.acb = 0x28; dssdev->panel.timings = sharp_ls_timings; + sd = kzalloc(sizeof(*sd), GFP_KERNEL); + if (!sd) + return -ENOMEM; + + dev_set_drvdata(&dssdev->dev, sd); + + memset(&props, 0, sizeof(struct backlight_properties)); + props.max_brightness = dssdev->max_backlight_level; + + bl = backlight_device_register("sharp-ls", &dssdev->dev, dssdev, + &sharp_ls_bl_ops, &props); + if (IS_ERR(bl)) { + r = PTR_ERR(bl); + kfree(sd); + return r; + } + sd->bl = bl; + + bl->props.fb_blank = FB_BLANK_UNBLANK; + bl->props.power = FB_BLANK_UNBLANK; + bl->props.brightness = dssdev->max_backlight_level; + r = sharp_ls_bl_update_status(bl); + if (r < 0) + dev_err(&dssdev->dev, "failed to set lcd brightness\n"); + return 0; } static void sharp_ls_panel_remove(struct omap_dss_device *dssdev) { + struct sharp_data *sd = dev_get_drvdata(&dssdev->dev); + struct backlight_device *bl = sd->bl; + + bl->props.power = FB_BLANK_POWERDOWN; + sharp_ls_bl_update_status(bl); + backlight_device_unregister(bl); + + kfree(sd); } static int sharp_ls_power_on(struct omap_dss_device *dssdev) diff --git a/drivers/video/omap2/displays/panel-taal.c b/drivers/video/omap2/displays/panel-taal.c index 4f3988a41082..aaf5d308a046 100644 --- a/drivers/video/omap2/displays/panel-taal.c +++ b/drivers/video/omap2/displays/panel-taal.c @@ -31,6 +31,7 @@ #include <linux/completion.h> #include <linux/workqueue.h> #include <linux/slab.h> +#include <linux/mutex.h> #include <plat/display.h> @@ -67,6 +68,8 @@ static int _taal_enable_te(struct omap_dss_device *dssdev, bool enable); struct taal_data { + struct mutex lock; + struct backlight_device *bldev; unsigned long hw_guard_end; /* next value of jiffies when we can @@ -510,6 +513,8 @@ static int taal_probe(struct omap_dss_device *dssdev) } td->dssdev = dssdev; + mutex_init(&td->lock); + td->esd_wq = create_singlethread_workqueue("taal_esd"); if (td->esd_wq == NULL) { dev_err(&dssdev->dev, "can't create ESD workqueue\n"); @@ -697,10 +702,9 @@ static int taal_power_on(struct omap_dss_device *dssdev) return 0; err: - dsi_bus_unlock(); - omapdss_dsi_display_disable(dssdev); err0: + dsi_bus_unlock(); if (dssdev->platform_disable) dssdev->platform_disable(dssdev); @@ -733,54 +737,96 @@ static void taal_power_off(struct omap_dss_device *dssdev) static int taal_enable(struct omap_dss_device *dssdev) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); int r; + dev_dbg(&dssdev->dev, "enable\n"); - if (dssdev->state != OMAP_DSS_DISPLAY_DISABLED) - return -EINVAL; + mutex_lock(&td->lock); + + if (dssdev->state != OMAP_DSS_DISPLAY_DISABLED) { + r = -EINVAL; + goto err; + } r = taal_power_on(dssdev); if (r) - return r; + goto err; dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; + mutex_unlock(&td->lock); + + return 0; +err: + dev_dbg(&dssdev->dev, "enable failed\n"); + mutex_unlock(&td->lock); return r; } static void taal_disable(struct omap_dss_device *dssdev) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); + dev_dbg(&dssdev->dev, "disable\n"); + mutex_lock(&td->lock); + if (dssdev->state == OMAP_DSS_DISPLAY_ACTIVE) taal_power_off(dssdev); dssdev->state = OMAP_DSS_DISPLAY_DISABLED; + + mutex_unlock(&td->lock); } static int taal_suspend(struct omap_dss_device *dssdev) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); + int r; + dev_dbg(&dssdev->dev, "suspend\n"); - if (dssdev->state != OMAP_DSS_DISPLAY_ACTIVE) - return -EINVAL; + mutex_lock(&td->lock); + + if (dssdev->state != OMAP_DSS_DISPLAY_ACTIVE) { + r = -EINVAL; + goto err; + } taal_power_off(dssdev); dssdev->state = OMAP_DSS_DISPLAY_SUSPENDED; + mutex_unlock(&td->lock); + return 0; +err: + mutex_unlock(&td->lock); + return r; } static int taal_resume(struct omap_dss_device *dssdev) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); int r; + dev_dbg(&dssdev->dev, "resume\n"); - if (dssdev->state != OMAP_DSS_DISPLAY_SUSPENDED) - return -EINVAL; + mutex_lock(&td->lock); + + if (dssdev->state != OMAP_DSS_DISPLAY_SUSPENDED) { + r = -EINVAL; + goto err; + } r = taal_power_on(dssdev); dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; + + mutex_unlock(&td->lock); + + return r; +err: + mutex_unlock(&td->lock); return r; } @@ -799,6 +845,7 @@ static int taal_update(struct omap_dss_device *dssdev, dev_dbg(&dssdev->dev, "update %d, %d, %d x %d\n", x, y, w, h); + mutex_lock(&td->lock); dsi_bus_lock(); if (!td->enabled) { @@ -820,18 +867,24 @@ static int taal_update(struct omap_dss_device *dssdev, goto err; /* note: no bus_unlock here. unlock is in framedone_cb */ + mutex_unlock(&td->lock); return 0; err: dsi_bus_unlock(); + mutex_unlock(&td->lock); return r; } static int taal_sync(struct omap_dss_device *dssdev) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); + dev_dbg(&dssdev->dev, "sync\n"); + mutex_lock(&td->lock); dsi_bus_lock(); dsi_bus_unlock(); + mutex_unlock(&td->lock); dev_dbg(&dssdev->dev, "sync done\n"); @@ -861,13 +914,16 @@ static int _taal_enable_te(struct omap_dss_device *dssdev, bool enable) static int taal_enable_te(struct omap_dss_device *dssdev, bool enable) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); int r; + mutex_lock(&td->lock); dsi_bus_lock(); r = _taal_enable_te(dssdev, enable); dsi_bus_unlock(); + mutex_unlock(&td->lock); return r; } @@ -875,7 +931,13 @@ static int taal_enable_te(struct omap_dss_device *dssdev, bool enable) static int taal_get_te(struct omap_dss_device *dssdev) { struct taal_data *td = dev_get_drvdata(&dssdev->dev); - return td->te_enabled; + int r; + + mutex_lock(&td->lock); + r = td->te_enabled; + mutex_unlock(&td->lock); + + return r; } static int taal_rotate(struct omap_dss_device *dssdev, u8 rotate) @@ -885,6 +947,7 @@ static int taal_rotate(struct omap_dss_device *dssdev, u8 rotate) dev_dbg(&dssdev->dev, "rotate %d\n", rotate); + mutex_lock(&td->lock); dsi_bus_lock(); if (td->enabled) { @@ -896,16 +959,24 @@ static int taal_rotate(struct omap_dss_device *dssdev, u8 rotate) td->rotate = rotate; dsi_bus_unlock(); + mutex_unlock(&td->lock); return 0; err: dsi_bus_unlock(); + mutex_unlock(&td->lock); return r; } static u8 taal_get_rotate(struct omap_dss_device *dssdev) { struct taal_data *td = dev_get_drvdata(&dssdev->dev); - return td->rotate; + int r; + + mutex_lock(&td->lock); + r = td->rotate; + mutex_unlock(&td->lock); + + return r; } static int taal_mirror(struct omap_dss_device *dssdev, bool enable) @@ -915,6 +986,7 @@ static int taal_mirror(struct omap_dss_device *dssdev, bool enable) dev_dbg(&dssdev->dev, "mirror %d\n", enable); + mutex_lock(&td->lock); dsi_bus_lock(); if (td->enabled) { r = taal_set_addr_mode(td->rotate, enable); @@ -925,23 +997,33 @@ static int taal_mirror(struct omap_dss_device *dssdev, bool enable) td->mirror = enable; dsi_bus_unlock(); + mutex_unlock(&td->lock); return 0; err: dsi_bus_unlock(); + mutex_unlock(&td->lock); return r; } static bool taal_get_mirror(struct omap_dss_device *dssdev) { struct taal_data *td = dev_get_drvdata(&dssdev->dev); - return td->mirror; + int r; + + mutex_lock(&td->lock); + r = td->mirror; + mutex_unlock(&td->lock); + + return r; } static int taal_run_test(struct omap_dss_device *dssdev, int test_num) { + struct taal_data *td = dev_get_drvdata(&dssdev->dev); u8 id1, id2, id3; int r; + mutex_lock(&td->lock); dsi_bus_lock(); r = taal_dcs_read_1(DCS_GET_ID1, &id1); @@ -955,9 +1037,11 @@ static int taal_run_test(struct omap_dss_device *dssdev, int test_num) goto err; dsi_bus_unlock(); + mutex_unlock(&td->lock); return 0; err: dsi_bus_unlock(); + mutex_unlock(&td->lock); return r; } @@ -971,12 +1055,16 @@ static int taal_memory_read(struct omap_dss_device *dssdev, unsigned buf_used = 0; struct taal_data *td = dev_get_drvdata(&dssdev->dev); - if (!td->enabled) - return -ENODEV; - if (size < w * h * 3) return -ENOMEM; + mutex_lock(&td->lock); + + if (!td->enabled) { + r = -ENODEV; + goto err1; + } + size = min(w * h * 3, dssdev->panel.timings.x_res * dssdev->panel.timings.y_res * 3); @@ -995,7 +1083,7 @@ static int taal_memory_read(struct omap_dss_device *dssdev, r = dsi_vc_set_max_rx_packet_size(TCH, plen); if (r) - goto err0; + goto err2; while (buf_used < size) { u8 dcs_cmd = first ? 0x2e : 0x3e; @@ -1006,7 +1094,7 @@ static int taal_memory_read(struct omap_dss_device *dssdev, if (r < 0) { dev_err(&dssdev->dev, "read error\n"); - goto err; + goto err3; } buf_used += r; @@ -1020,16 +1108,18 @@ static int taal_memory_read(struct omap_dss_device *dssdev, dev_err(&dssdev->dev, "signal pending, " "aborting memory read\n"); r = -ERESTARTSYS; - goto err; + goto err3; } } r = buf_used; -err: +err3: dsi_vc_set_max_rx_packet_size(TCH, 1); -err0: +err2: dsi_bus_unlock(); +err1: + mutex_unlock(&td->lock); return r; } @@ -1041,8 +1131,12 @@ static void taal_esd_work(struct work_struct *work) u8 state1, state2; int r; - if (!td->enabled) + mutex_lock(&td->lock); + + if (!td->enabled) { + mutex_unlock(&td->lock); return; + } dsi_bus_lock(); @@ -1084,16 +1178,19 @@ static void taal_esd_work(struct work_struct *work) queue_delayed_work(td->esd_wq, &td->esd_work, TAAL_ESD_CHECK_PERIOD); + mutex_unlock(&td->lock); return; err: dev_err(&dssdev->dev, "performing LCD reset\n"); - taal_disable(dssdev); - taal_enable(dssdev); + taal_power_off(dssdev); + taal_power_on(dssdev); dsi_bus_unlock(); queue_delayed_work(td->esd_wq, &td->esd_work, TAAL_ESD_CHECK_PERIOD); + + mutex_unlock(&td->lock); } static int taal_set_update_mode(struct omap_dss_device *dssdev, diff --git a/drivers/video/omap2/dss/Kconfig b/drivers/video/omap2/dss/Kconfig index 87afb81b2c44..43b64403eaa4 100644 --- a/drivers/video/omap2/dss/Kconfig +++ b/drivers/video/omap2/dss/Kconfig @@ -36,6 +36,12 @@ config OMAP2_DSS_COLLECT_IRQ_STATS <debugfs>/omapdss/dispc_irq for DISPC interrupts, and <debugfs>/omapdss/dsi_irq for DSI interrupts. +config OMAP2_DSS_DPI + bool "DPI support" + default y + help + DPI Interface. This is the Parallel Display Interface. + config OMAP2_DSS_RFBI bool "RFBI support" default n diff --git a/drivers/video/omap2/dss/Makefile b/drivers/video/omap2/dss/Makefile index 980c72c2db98..d71b5d9d71b1 100644 --- a/drivers/video/omap2/dss/Makefile +++ b/drivers/video/omap2/dss/Makefile @@ -1,5 +1,6 @@ obj-$(CONFIG_OMAP2_DSS) += omapdss.o -omapdss-y := core.o dss.o dispc.o dpi.o display.o manager.o overlay.o +omapdss-y := core.o dss.o dispc.o display.o manager.o overlay.o +omapdss-$(CONFIG_OMAP2_DSS_DPI) += dpi.o omapdss-$(CONFIG_OMAP2_DSS_RFBI) += rfbi.o omapdss-$(CONFIG_OMAP2_DSS_VENC) += venc.o omapdss-$(CONFIG_OMAP2_DSS_SDI) += sdi.o diff --git a/drivers/video/omap2/dss/core.c b/drivers/video/omap2/dss/core.c index 7ebe50b335ed..b3a498f22d36 100644 --- a/drivers/video/omap2/dss/core.c +++ b/drivers/video/omap2/dss/core.c @@ -482,6 +482,14 @@ static void dss_uninitialize_debugfs(void) if (dss_debugfs_dir) debugfs_remove_recursive(dss_debugfs_dir); } +#else /* CONFIG_DEBUG_FS && CONFIG_OMAP2_DSS_DEBUG_SUPPORT */ +static inline int dss_initialize_debugfs(void) +{ + return 0; +} +static inline void dss_uninitialize_debugfs(void) +{ +} #endif /* CONFIG_DEBUG_FS && CONFIG_OMAP2_DSS_DEBUG_SUPPORT */ /* PLATFORM DEVICE */ @@ -499,7 +507,7 @@ static int omap_dss_probe(struct platform_device *pdev) r = dss_get_clocks(); if (r) - goto fail0; + goto err_clocks; dss_clk_enable_all_no_ctx(); @@ -515,64 +523,64 @@ static int omap_dss_probe(struct platform_device *pdev) r = dss_init(skip_init); if (r) { DSSERR("Failed to initialize DSS\n"); - goto fail0; + goto err_dss; } -#ifdef CONFIG_OMAP2_DSS_RFBI r = rfbi_init(); if (r) { DSSERR("Failed to initialize rfbi\n"); - goto fail0; + goto err_rfbi; } -#endif r = dpi_init(pdev); if (r) { DSSERR("Failed to initialize dpi\n"); - goto fail0; + goto err_dpi; } r = dispc_init(); if (r) { DSSERR("Failed to initialize dispc\n"); - goto fail0; + goto err_dispc; } -#ifdef CONFIG_OMAP2_DSS_VENC + r = venc_init(pdev); if (r) { DSSERR("Failed to initialize venc\n"); - goto fail0; + goto err_venc; } -#endif + if (cpu_is_omap34xx()) { -#ifdef CONFIG_OMAP2_DSS_SDI r = sdi_init(skip_init); if (r) { DSSERR("Failed to initialize SDI\n"); - goto fail0; + goto err_sdi; } -#endif -#ifdef CONFIG_OMAP2_DSS_DSI + r = dsi_init(pdev); if (r) { DSSERR("Failed to initialize DSI\n"); - goto fail0; + goto err_dsi; } -#endif } -#if defined(CONFIG_DEBUG_FS) && defined(CONFIG_OMAP2_DSS_DEBUG_SUPPORT) r = dss_initialize_debugfs(); if (r) - goto fail0; -#endif + goto err_debugfs; for (i = 0; i < pdata->num_devices; ++i) { struct omap_dss_device *dssdev = pdata->devices[i]; r = omap_dss_register_device(dssdev); - if (r) - DSSERR("device reg failed %d\n", i); + if (r) { + DSSERR("device %d %s register failed %d\n", i, + dssdev->name ?: "unnamed", r); + + while (--i >= 0) + omap_dss_unregister_device(pdata->devices[i]); + + goto err_register; + } if (def_disp_name && strcmp(def_disp_name, dssdev->name) == 0) pdata->default_device = dssdev; @@ -582,8 +590,29 @@ static int omap_dss_probe(struct platform_device *pdev) return 0; - /* XXX fail correctly */ -fail0: +err_register: + dss_uninitialize_debugfs(); +err_debugfs: + if (cpu_is_omap34xx()) + dsi_exit(); +err_dsi: + if (cpu_is_omap34xx()) + sdi_exit(); +err_sdi: + venc_exit(); +err_venc: + dispc_exit(); +err_dispc: + dpi_exit(); +err_dpi: + rfbi_exit(); +err_rfbi: + dss_exit(); +err_dss: + dss_clk_disable_all_no_ctx(); + dss_put_clocks(); +err_clocks: + return r; } @@ -593,25 +622,15 @@ static int omap_dss_remove(struct platform_device *pdev) int i; int c; -#if defined(CONFIG_DEBUG_FS) && defined(CONFIG_OMAP2_DSS_DEBUG_SUPPORT) dss_uninitialize_debugfs(); -#endif -#ifdef CONFIG_OMAP2_DSS_VENC venc_exit(); -#endif dispc_exit(); dpi_exit(); -#ifdef CONFIG_OMAP2_DSS_RFBI rfbi_exit(); -#endif if (cpu_is_omap34xx()) { -#ifdef CONFIG_OMAP2_DSS_DSI dsi_exit(); -#endif -#ifdef CONFIG_OMAP2_DSS_SDI sdi_exit(); -#endif } dss_exit(); diff --git a/drivers/video/omap2/dss/display.c b/drivers/video/omap2/dss/display.c index 6a74ea116d29..ef8c8529dda2 100644 --- a/drivers/video/omap2/dss/display.c +++ b/drivers/video/omap2/dss/display.c @@ -392,7 +392,9 @@ void dss_init_device(struct platform_device *pdev, int r; switch (dssdev->type) { +#ifdef CONFIG_OMAP2_DSS_DPI case OMAP_DISPLAY_TYPE_DPI: +#endif #ifdef CONFIG_OMAP2_DSS_RFBI case OMAP_DISPLAY_TYPE_DBI: #endif @@ -413,9 +415,11 @@ void dss_init_device(struct platform_device *pdev, } switch (dssdev->type) { +#ifdef CONFIG_OMAP2_DSS_DPI case OMAP_DISPLAY_TYPE_DPI: r = dpi_init_display(dssdev); break; +#endif #ifdef CONFIG_OMAP2_DSS_RFBI case OMAP_DISPLAY_TYPE_DBI: r = rfbi_init_display(dssdev); @@ -541,7 +545,10 @@ int dss_resume_all_devices(void) static int dss_disable_device(struct device *dev, void *data) { struct omap_dss_device *dssdev = to_dss_device(dev); - dssdev->driver->disable(dssdev); + + if (dssdev->state != OMAP_DSS_DISPLAY_DISABLED) + dssdev->driver->disable(dssdev); + return 0; } diff --git a/drivers/video/omap2/dss/dss.c b/drivers/video/omap2/dss/dss.c index 54344184dd73..24b18258654f 100644 --- a/drivers/video/omap2/dss/dss.c +++ b/drivers/video/omap2/dss/dss.c @@ -223,7 +223,13 @@ void dss_dump_clocks(struct seq_file *s) seq_printf(s, "dpll4_ck %lu\n", dpll4_ck_rate); - seq_printf(s, "dss1_alwon_fclk = %lu / %lu * 2 = %lu\n", + if (cpu_is_omap3630()) + seq_printf(s, "dss1_alwon_fclk = %lu / %lu = %lu\n", + dpll4_ck_rate, + dpll4_ck_rate / dpll4_m4_ck_rate, + dss_clk_get_rate(DSS_CLK_FCK1)); + else + seq_printf(s, "dss1_alwon_fclk = %lu / %lu * 2 = %lu\n", dpll4_ck_rate, dpll4_ck_rate / dpll4_m4_ck_rate, dss_clk_get_rate(DSS_CLK_FCK1)); @@ -293,7 +299,8 @@ int dss_calc_clock_rates(struct dss_clock_info *cinfo) { unsigned long prate; - if (cinfo->fck_div > 16 || cinfo->fck_div == 0) + if (cinfo->fck_div > (cpu_is_omap3630() ? 32 : 16) || + cinfo->fck_div == 0) return -EINVAL; prate = clk_get_rate(clk_get_parent(dss.dpll4_m4_ck)); @@ -329,7 +336,10 @@ int dss_get_clock_div(struct dss_clock_info *cinfo) if (cpu_is_omap34xx()) { unsigned long prate; prate = clk_get_rate(clk_get_parent(dss.dpll4_m4_ck)); - cinfo->fck_div = prate / (cinfo->fck / 2); + if (cpu_is_omap3630()) + cinfo->fck_div = prate / (cinfo->fck); + else + cinfo->fck_div = prate / (cinfo->fck / 2); } else { cinfo->fck_div = 0; } @@ -402,10 +412,14 @@ retry: goto found; } else if (cpu_is_omap34xx()) { - for (fck_div = 16; fck_div > 0; --fck_div) { + for (fck_div = (cpu_is_omap3630() ? 32 : 16); + fck_div > 0; --fck_div) { struct dispc_clock_info cur_dispc; - fck = prate / fck_div * 2; + if (cpu_is_omap3630()) + fck = prate / fck_div; + else + fck = prate / fck_div * 2; if (fck > DISPC_MAX_FCK) continue; diff --git a/drivers/video/omap2/dss/dss.h b/drivers/video/omap2/dss/dss.h index 24326a5fd292..786f433fd571 100644 --- a/drivers/video/omap2/dss/dss.h +++ b/drivers/video/omap2/dss/dss.h @@ -242,11 +242,22 @@ int dss_calc_clock_div(bool is_tft, unsigned long req_pck, struct dispc_clock_info *dispc_cinfo); /* SDI */ +#ifdef CONFIG_OMAP2_DSS_SDI int sdi_init(bool skip_init); void sdi_exit(void); int sdi_init_display(struct omap_dss_device *display); +#else +static inline int sdi_init(bool skip_init) +{ + return 0; +} +static inline void sdi_exit(void) +{ +} +#endif /* DSI */ +#ifdef CONFIG_OMAP2_DSS_DSI int dsi_init(struct platform_device *pdev); void dsi_exit(void); @@ -270,11 +281,30 @@ void dsi_pll_uninit(void); void dsi_get_overlay_fifo_thresholds(enum omap_plane plane, u32 fifo_size, enum omap_burst_size *burst_size, u32 *fifo_low, u32 *fifo_high); +#else +static inline int dsi_init(struct platform_device *pdev) +{ + return 0; +} +static inline void dsi_exit(void) +{ +} +#endif /* DPI */ +#ifdef CONFIG_OMAP2_DSS_DPI int dpi_init(struct platform_device *pdev); void dpi_exit(void); int dpi_init_display(struct omap_dss_device *dssdev); +#else +static inline int dpi_init(struct platform_device *pdev) +{ + return 0; +} +static inline void dpi_exit(void) +{ +} +#endif /* DISPC */ int dispc_init(void); @@ -362,12 +392,23 @@ int dispc_get_clock_div(struct dispc_clock_info *cinfo); /* VENC */ +#ifdef CONFIG_OMAP2_DSS_VENC int venc_init(struct platform_device *pdev); void venc_exit(void); void venc_dump_regs(struct seq_file *s); int venc_init_display(struct omap_dss_device *display); +#else +static inline int venc_init(struct platform_device *pdev) +{ + return 0; +} +static inline void venc_exit(void) +{ +} +#endif /* RFBI */ +#ifdef CONFIG_OMAP2_DSS_RFBI int rfbi_init(void); void rfbi_exit(void); void rfbi_dump_regs(struct seq_file *s); @@ -379,6 +420,15 @@ void rfbi_transfer_area(u16 width, u16 height, void rfbi_set_timings(int rfbi_module, struct rfbi_timings *t); unsigned long rfbi_get_max_tx_rate(void); int rfbi_init_display(struct omap_dss_device *display); +#else +static inline int rfbi_init(void) +{ + return 0; +} +static inline void rfbi_exit(void) +{ +} +#endif #ifdef CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS diff --git a/drivers/video/omap2/dss/manager.c b/drivers/video/omap2/dss/manager.c index 0820986d4a68..9e1fbe531bf0 100644 --- a/drivers/video/omap2/dss/manager.c +++ b/drivers/video/omap2/dss/manager.c @@ -843,6 +843,7 @@ static void configure_manager(enum omap_channel channel) c = &dss_cache.manager_cache[channel]; + dispc_set_default_color(channel, c->default_color); dispc_set_trans_key(channel, c->trans_key_type, c->trans_key); dispc_enable_trans_key(channel, c->trans_enabled); dispc_enable_alpha_blending(channel, c->alpha_enabled); @@ -940,6 +941,22 @@ static int configure_dispc(void) return r; } +/* Make the coordinates even. There are some strange problems with OMAP and + * partial DSI update when the update widths are odd. */ +static void make_even(u16 *x, u16 *w) +{ + u16 x1, x2; + + x1 = *x; + x2 = *x + *w; + + x1 &= ~1; + x2 = ALIGN(x2, 2); + + *x = x1; + *w = x2 - x1; +} + /* Configure dispc for partial update. Return possibly modified update * area */ void dss_setup_partial_planes(struct omap_dss_device *dssdev, @@ -968,6 +985,8 @@ void dss_setup_partial_planes(struct omap_dss_device *dssdev, return; } + make_even(&x, &w); + spin_lock_irqsave(&dss_cache.lock, flags); /* We need to show the whole overlay if it is scaled. So look for @@ -1029,6 +1048,8 @@ void dss_setup_partial_planes(struct omap_dss_device *dssdev, w = x2 - x1; h = y2 - y1; + make_even(&x, &w); + DSSDBG("changing upd area due to ovl(%d) scaling %d,%d %dx%d\n", i, x, y, w, h); } diff --git a/drivers/video/omap2/dss/sdi.c b/drivers/video/omap2/dss/sdi.c index 12eb4042dd82..ee07a3cc22ef 100644 --- a/drivers/video/omap2/dss/sdi.c +++ b/drivers/video/omap2/dss/sdi.c @@ -23,13 +23,16 @@ #include <linux/clk.h> #include <linux/delay.h> #include <linux/err.h> +#include <linux/regulator/consumer.h> #include <plat/display.h> +#include <plat/cpu.h> #include "dss.h" static struct { bool skip_init; bool update_enabled; + struct regulator *vdds_sdi_reg; } sdi; static void sdi_basic_init(void) @@ -57,6 +60,10 @@ int omapdss_sdi_display_enable(struct omap_dss_device *dssdev) goto err0; } + r = regulator_enable(sdi.vdds_sdi_reg); + if (r) + goto err1; + /* In case of skip_init sdi_init has already enabled the clocks */ if (!sdi.skip_init) dss_clk_enable(DSS_CLK_ICK | DSS_CLK_FCK1); @@ -115,19 +122,12 @@ int omapdss_sdi_display_enable(struct omap_dss_device *dssdev) dssdev->manager->enable(dssdev->manager); - if (dssdev->driver->enable) { - r = dssdev->driver->enable(dssdev); - if (r) - goto err3; - } - sdi.skip_init = 0; return 0; -err3: - dssdev->manager->disable(dssdev->manager); err2: dss_clk_disable(DSS_CLK_ICK | DSS_CLK_FCK1); + regulator_disable(sdi.vdds_sdi_reg); err1: omap_dss_stop_device(dssdev); err0: @@ -137,15 +137,14 @@ EXPORT_SYMBOL(omapdss_sdi_display_enable); void omapdss_sdi_display_disable(struct omap_dss_device *dssdev) { - if (dssdev->driver->disable) - dssdev->driver->disable(dssdev); - dssdev->manager->disable(dssdev->manager); dss_sdi_disable(); dss_clk_disable(DSS_CLK_ICK | DSS_CLK_FCK1); + regulator_disable(sdi.vdds_sdi_reg); + omap_dss_stop_device(dssdev); } EXPORT_SYMBOL(omapdss_sdi_display_disable); @@ -162,6 +161,11 @@ int sdi_init(bool skip_init) /* we store this for first display enable, then clear it */ sdi.skip_init = skip_init; + sdi.vdds_sdi_reg = dss_get_vdds_sdi(); + if (IS_ERR(sdi.vdds_sdi_reg)) { + DSSERR("can't get VDDS_SDI regulator\n"); + return PTR_ERR(sdi.vdds_sdi_reg); + } /* * Enable clocks already here, otherwise there would be a toggle * of them until sdi_display_enable is called. diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c index f0ba5732d84a..eff35050e28a 100644 --- a/drivers/video/omap2/dss/venc.c +++ b/drivers/video/omap2/dss/venc.c @@ -479,12 +479,6 @@ static int venc_panel_enable(struct omap_dss_device *dssdev) goto err1; } - if (dssdev->platform_enable) { - r = dssdev->platform_enable(dssdev); - if (r) - goto err2; - } - venc_power_on(dssdev); venc.wss_data = 0; @@ -494,13 +488,9 @@ static int venc_panel_enable(struct omap_dss_device *dssdev) /* wait couple of vsyncs until enabling the LCD */ msleep(50); - mutex_unlock(&venc.venc_lock); - - return r; -err2: - venc_power_off(dssdev); err1: mutex_unlock(&venc.venc_lock); + return r; } @@ -524,9 +514,6 @@ static void venc_panel_disable(struct omap_dss_device *dssdev) /* wait at least 5 vsyncs after disabling the LCD */ msleep(100); - if (dssdev->platform_disable) - dssdev->platform_disable(dssdev); - dssdev->state = OMAP_DSS_DISPLAY_DISABLED; end: mutex_unlock(&venc.venc_lock); diff --git a/drivers/video/omap2/omapfb/omapfb-ioctl.c b/drivers/video/omap2/omapfb/omapfb-ioctl.c index 1ffa760b8545..9c7361871d78 100644 --- a/drivers/video/omap2/omapfb/omapfb-ioctl.c +++ b/drivers/video/omap2/omapfb/omapfb-ioctl.c @@ -183,13 +183,14 @@ int omapfb_update_window(struct fb_info *fbi, struct omapfb2_device *fbdev = ofbi->fbdev; int r; + if (!lock_fb_info(fbi)) + return -ENODEV; omapfb_lock(fbdev); - lock_fb_info(fbi); r = omapfb_update_window_nolock(fbi, x, y, w, h); - unlock_fb_info(fbi); omapfb_unlock(fbdev); + unlock_fb_info(fbi); return r; } diff --git a/drivers/video/omap2/omapfb/omapfb-sysfs.c b/drivers/video/omap2/omapfb/omapfb-sysfs.c index 62bb88f5c192..5179219128bd 100644 --- a/drivers/video/omap2/omapfb/omapfb-sysfs.c +++ b/drivers/video/omap2/omapfb/omapfb-sysfs.c @@ -57,7 +57,8 @@ static ssize_t store_rotate_type(struct device *dev, if (rot_type != OMAP_DSS_ROT_DMA && rot_type != OMAP_DSS_ROT_VRFB) return -EINVAL; - lock_fb_info(fbi); + if (!lock_fb_info(fbi)) + return -ENODEV; r = 0; if (rot_type == ofbi->rotation_type) @@ -105,7 +106,8 @@ static ssize_t store_mirror(struct device *dev, if (mirror != 0 && mirror != 1) return -EINVAL; - lock_fb_info(fbi); + if (!lock_fb_info(fbi)) + return -ENODEV; ofbi->mirror = mirror; @@ -137,8 +139,9 @@ static ssize_t show_overlays(struct device *dev, ssize_t l = 0; int t; + if (!lock_fb_info(fbi)) + return -ENODEV; omapfb_lock(fbdev); - lock_fb_info(fbi); for (t = 0; t < ofbi->num_overlays; t++) { struct omap_overlay *ovl = ofbi->overlays[t]; @@ -154,8 +157,8 @@ static ssize_t show_overlays(struct device *dev, l += snprintf(buf + l, PAGE_SIZE - l, "\n"); - unlock_fb_info(fbi); omapfb_unlock(fbdev); + unlock_fb_info(fbi); return l; } @@ -195,8 +198,9 @@ static ssize_t store_overlays(struct device *dev, struct device_attribute *attr, if (buf[len - 1] == '\n') len = len - 1; + if (!lock_fb_info(fbi)) + return -ENODEV; omapfb_lock(fbdev); - lock_fb_info(fbi); if (len > 0) { char *p = (char *)buf; @@ -303,8 +307,8 @@ static ssize_t store_overlays(struct device *dev, struct device_attribute *attr, r = count; out: - unlock_fb_info(fbi); omapfb_unlock(fbdev); + unlock_fb_info(fbi); return r; } @@ -317,7 +321,8 @@ static ssize_t show_overlays_rotate(struct device *dev, ssize_t l = 0; int t; - lock_fb_info(fbi); + if (!lock_fb_info(fbi)) + return -ENODEV; for (t = 0; t < ofbi->num_overlays; t++) { l += snprintf(buf + l, PAGE_SIZE - l, "%s%d", @@ -345,7 +350,8 @@ static ssize_t store_overlays_rotate(struct device *dev, if (buf[len - 1] == '\n') len = len - 1; - lock_fb_info(fbi); + if (!lock_fb_info(fbi)) + return -ENODEV; if (len > 0) { char *p = (char *)buf; @@ -416,7 +422,8 @@ static ssize_t store_size(struct device *dev, struct device_attribute *attr, size = PAGE_ALIGN(simple_strtoul(buf, NULL, 0)); - lock_fb_info(fbi); + if (!lock_fb_info(fbi)) + return -ENODEV; for (i = 0; i < ofbi->num_overlays; i++) { if (ofbi->overlays[i]->info.enabled) { |